RENNSTALL MOTO RMC-011200 Manuel utilisateur

Marque: RENNSTALL MOTO

Modèle: RMC-011200

Taper: Manuel utilisateur

Front fairing

for:

Triumph Speed Twin 1200 (Model Year 2022)

Part number: RMC-011200

Instruction Manual

Version: 1

Date: 21.03.2022

Read and save this manual for future

reference. Before attempting to assemble,

install, operate the products, please

ensure a complete understanding of the

instructions and any other documents

related to the products, including but not

limited to a provided disclaimer. Failure to

comply with instructions in this manual

could result in serious injury, death and/or

property damage. This manual is subject

to change without notice.

Important note

Products of Rennstall Moto or any of its affiliates (collectively, "Rennstall")

are sold "AS IS" without any express or implied warranties. To the fullest

extent permitted by law, Rennstall disclaims any and all warranties.

Installation or usage of Rennstall's products may affect warranties of utilized

vehicles, such as motorcycles.

ANY BUYER OR USER OF PRODUCTS OF RENNSTALL EXPRESSLY AND

VOLUNTARILY ASSUMES ANY AND ALL RISKS INCLUDING, BUT NOT

LIMITED TO, DEATH, DISABILITY, AND/OR SERIOUS PHYSICAL INJURY,

RELATED TO THE INSTALLATION OR USAGE OF SUCH PRODUCTS BY

BUYER, USER OR ANY THIRD PARTY.

Under no circumstances are Rennstall's products to be used on public roads

or any other streets, highways, or off-road areas. Rennstall's products are

solely intended for use on vehicles operated on closed-course facilities,

show events or racetracks, each with appropriate supervision of qualified

individuals to ensure safety of all involved parties.

Always use caution when installing or using Rennstall's products, adhere to

all instructions, only utilize provided hardware or tools, and do not modify

or otherwise alter the products.

Prior to any usage of Rennstall's products, a buyer or user shall inspect and

verify the integrity of the entire vehicle upon which such products are

mounted, installed, or otherwise attached. Vehicles are to be inspected

before each use for evidence of damage, defect, or wear to ensure the

vehicle is fit and ready for operation. Without limiting the generality of the

foregoing, buyer or user shall specifically inspect all bolts after each usage

in excess of Two Hundred (200) kilometers or One Hundred Twenty-Five

(125) miles.

Under no circumstances and under no legal theory whether in tort, contract,

or otherwise shall Rennstall or its employees, agents, representatives,

successors, or assigns, be liable to a buyer, user or any other person for any

direct, indirect, special, incidental, or consequential damages of any kind

arising out of or relating to the installation or usage of the products,

even if Rennstall has been informed of the possibility of such

damages, or for any claim by any other party.

Front Fairing (Fig.1)

Part Number: RMC-011200

Time:

approx. 1h

Preparation:

Remember headlight height/position.

(Tip: Switch the headlight on and mark the border

between light and dark on the wall with a piece of

tape.)

Steps:

Remove the two M8 bolts either side of the

headlight. Be careful the headlight doesn‘t

drop down.

Fig.2

Position the cylindrical spacers on the outside

of the headlight brackets, the side with the

smaller diameter pointing towards the

headlight (possibly already pre-assembled

inside the fairing).

(Tip: Hold spacers in place with some sealant

or modeling clay.)

Fig.3

Fit the fairing and put the headlight back into

position. Loosely insert the two new TX M8

bolts and countersunk washers. Do not yet

tighten.

Adjust the headlight height according to the

marking on the wall you made earlier. Now

torque down the two TX M8 bolts to 18Nm

(13.3 ft·lb).

Fig.1

Insert the cylindrical part of the “anti twist

bracket“ into the underside of the head tube.

Use the long hole on the bracket and torque

the bolt down to 6Nm (4.4 ft·lb). The bracket

can be positioned and bent into shape to

achieve the desired angle of the fairing

(depending on the type of handlebar and

height of fairing in relation to triple trees).

Fix the other side to the inside of the fairing

using the TX M6 bolt, countersunk washer and

tooth nut. Torque down to 8Nm (5.9 ft·lb).

Fig.4

Fig.1

Fig.2

Fig.3

Fig.4

RENNSTALL MOTO RMC-011200 Manuel utilisateur

Marque: RENNSTALL MOTO

Modèle: RMC-011200

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: RENNSTALL MOTO RMC-011200 User manual

Documents connexes

RENNSTALL MOTO RMC-011000 Manuel utilisateur

RENNSTALL MOTO RMC-011200 Manuel utilisateur

RENNSTALL MOTO RMC-011200 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents