EarthWise SN75022 Mode d'emploi

Model SN75022

OWNER’S MANUAL

22-IN Corded Snow Thrower

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY,

PARTS, SERVICE QUESTIONS? GO TO AMERICANLAWNMOWER.COM OR

CALL 1-800-633-1501 BETWEEN 8 AM – 5 PM EST, MONDAY-FRIDAY FOR

ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

This product has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the owner’s manual

before using this product.

Quick Start Instruction

From Page 9

Precautions that involve your safety.

CAUTION! Read the instruction manual and follow the warning and safety instructions!

CAUTION! Remove plug from outlet immediately if the cable is damaged or cut.

SWITCH OFF! the machine, wait until it comes to a complete standstill and remove plug from outlet

prior to maintenance, cleaning or repair work!

CAUTION! Always wear eye and ear protection.

Wear safe, sturdy, nonskid footwear!

DANGER! objects may be thrown out at high speed when motor is running. Do not walk in front of running

machine.

Keep bystanders at a safe distance.

DANGER! Rotating blades. Keep hands and feet at a safe distance.

Do not place hand under auger.

Keep the electrical cord free of the auger. The auger may damage the cord and cause contact with live

parts.

Do not place hand in front of chute deflector.

Do not expose to rain or use in damp locations.

DANGER! Risk of electric shock.

Do not use in rain or electrical storms.

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your Local Authority or retailer for recycling advice.

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

2

Model SN75022

TO REDUCE RISK OF INJURY: Before any use

be sure everyone using this product reads and

understands all safety instructions and other

information contained in this manual.

CAUTION: Wear appropriate personal hearing

protection during use. Under some conditions

and duration of use, noise from this product may

contribute to hearing loss.

Save these instructions and review frequently prior

to use and in instructing others.

WARNING: When using electric appliances,

basic safety precautions should always be followed

to reduce risk of fire, electric shock, and personal

injury, including the following:

READ ALL INSTRUCTIONS

CHECK FOR DAMAGED PARTS - Before further use

of the product, any part that is damaged should be

carefully checked to determine that it will operate

properly and perform its intended function. Check for

alignment of moving parts, binding of moving parts,

breakage of parts, mounting and any other condition

that may affect its operation. Any part that is damaged

should be properly repaired or replaced. For assistance

call our customer service help line at 1-800-633-1501.

AVOID DANGEROUS ENVIRONMENTS - Do not

operate in gaseous or explosive atmospheres. Motors

in these products normally spark, and the sparks might

ignite fumes.

KEEP CHILDREN AWAY - All visitors, children and

pets should stay at a safe distance from the work area.

DRESS PROPERLY- Don’t wear loose clothing or

jewelry and wear protective hair covering to contain

long hair. They can be caught in moving parts.

Wear safe, sturdy, nonskid footwear. Maintain good

footing at all times, especially on slopes.

USE SAFETY GLASSES - Wear safety glasses with

side shields or goggles that are marked to comply with

ANSI Z87.1 standard when operating this product.

DOUBLE INSULATION – The snow thrower has double

insulation. This means that all external metal parts are

insulated from the electrical supply. This is achieved by

introducing an insulation layer between electrical and

mechanical parts. The double insulation guarantees

you the greatest possible safety.

WARNING: Use outdoor extension cords marked

SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or

SJTOWA. These cords are rated for outdoor use and

reduce the risk of electric shock.

POLARIZED PLUGS-To reduce the risk of electric

shock, this product has a polarized plug. Polarized

connections will fit together only one way.Make sure

that the receptacle end of the extension cord has large

and small blade slot widths. If the plug does not fit fully

into the extension cord, reverse the plug. If it still does

not fit, obtain a suitable extension cord. If the extension

cord does not fit fully into the outlet, contact a qualified

electrician to install the proper outlet. Do not change

the plug on the tool or the extension cord in any way.

EXTENSION CORD. Make sure your extension

cord is in good condition. When using an extension

cord be sure it is heavy enough to carry the current

your product will draw. An undersized extension

cord will cause a drop in line voltage resulting in

loss of power and overheating. The following table

shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt,

use the next heavier gage. The smaller the gage

number, the heavier the cord.

It is possible to tie two extension cords together in

a knot to prevent them from

becoming disconnected during

use. Make the knot as shown,

then connect the plug end of

the power cord into the recepta-

cle end of the extension cord.

This method can also be used

to tie two extension cords together.

Use one of the plug-receptacle retaining straps or

connectors described in this manual.

WARNING: Keep all connections dry and off the

ground. Do not touch plug with wet hands. Failure

to do so can result in serious personal injury or

death.

Be aware of the extension cord while operating the

snow thrower. Be careful not to trip on the cord.

Always keep the cord away from the auger.

IMPORTANT SAFETY WARNINGS

GENERAL SAFETY

3

Model SN75022

Minimum Gage for Cord Sets

Volts Total Length of cord in Feet

120V 0-25 26-50 51-100 101-150

Ampere Rating

More Not More American wire Gage

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

Operation of the snow thrower in the hand-held

position is unsafe except in accordance with the

special instructions for such use provided in the

operator’s manual.

CAUTION: Never throw snow towards people,

pets or cars and never allow anyone in front of the

snow thrower while in operation.

Objects that might clog the snow thrower or cause

other damage can be hidden in the snow. Clear the

area of doormats, sleds, boards, wires and other

debris prior to use.

If the auger strikes a foreign object, stop the snow

thrower and examine it for signs of damage. Make

any necessary repairs before restarting and

continuing to work.

STAY ALERT - Watch what you are doing. Use

common sense. Do not operate the snow thrower

when you are tired or under the influence of drugs,

alcohol or medications.

If the snow thrower starts to vibrate abnormally, turn

it off immediately and check for the cause. Vibration

is generally a warning of trouble.

Always turn off the snow thrower, wait until the

auger comes to a complete stop and disconnect

from the power supply before carrying out

maintenance or repairs.

Never operate the snow thrower without proper

guards and other safety protective devices in place

and working.

When servicing use only identical replacement

parts.

CAUTION: Auger does not stop immediately

after the snow thrower is turned off.

CAUTION: Risk of injury. This snow thrower is

capable of causing serious injury. Do not put hands,

feet or any body part or clothing near the rotating

auger.

WARNING: California Proposition 65:

This product contains chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm.

WARNING: Cancer and Reproductive Harm

www.P65Warnings.ca.gov.

GROUND FAULT CIRCUIT INTERRUPTER (GFCI)

protection should be provided on the circuit or outlet

to be used for the snow thrower. Receptacles are

available having built-in GFCI protection and may

be used.

WARNING: Never put your hands near the auger

to remove snow, sticks or other debris. Blocked au-

ger can “spring back” when cleared and may cause

personal injury even when the snow thrower is

stopped. Always use a wooden stick such as a

broom handle to clear blockages.

DISCONNECT UNIT from the power supply when

not in use or when servicing or cleaning. Do not

leave unattended.

DON’T ABUSE CORD - Never carry this product

by the cord or yank the cord to disconnect from the

receptacle. Keep cord from heat, oil, and sharp

edges.

USE RIGHT APPLIANCE - Do not use this product

for any job except that for which it is intended.

DO NOT OVERLOAD the snow thrower by using at

too fast a rate to clear the snow. The snow thrower

will perform better and safer at the rate for which it

was designed.

DON’T OVERREACH - Guide the snow thrower at a

walking pace only. Keep proper footing and balance

at all times.

LIGHTING - Only operate your snow thrower in

daylight or good artificial light.

STORE IDLE UNIT INDOORS-When not in use, the

snow thrower should be stored indoors in a dry area

out of reach of children.

MAINTAIN UNIT WITH CARE-Keep clean for best

performance and to reduce the risk of injury. Inspect

extension cord periodically and replace if damaged.

Keep handles dry, clean and free from oil.

Do not operate the snow thrower on a slope that is

too steep for safe operation. When on slopes, slow

down and make sure you have good footing.

Before starting the snow thrower make sure the

auger is not touching any object and is free to move.

Do not attempt to clear snow from a gravel or

crushed rock surface. This product is only intended

for use on hard, flat surfaces free of sand, stone and

debris, wires or any other objects.

GENERAL SAFETY

4

Model SN75022

PRODUCT SPECIFICATIONS

Model: SN75022

Power supply voltage: 120V-60HZ Clearing width: 22 inches (560 mm)

Idle speed: 2300 RPM Max clearing depth: 12 inches (305 mm)

Power consumption: 15 Amp Clearing capacity: 880 pounds/minute

Weight: 31 pounds Throwing distance: Up to 30 feet

5

Model SN75022

PARTS LIST

7 Knob

8 Cable retainer

No. Description

9 Center handle

10 Cotter Pin

11 Auxiliary handle

12 Lower handle

13 Wheel assy.

14 Scraper blade

15 Auger

16 Side cover

17 Discharge chute

18 Chute deflector

No. Description

1 Upper handle

2 Bail wire

3 Switch button

4 Cable clip

5 Crank handle

5A Upper crank

5B Lower crank

6 J bolt

ASSEMBLY

6

Model SN75022

UNPACKING

This product requires assembly.

Carefully remove everything from the box. Make sure that

all items listed in the packing list are included.

Inspect all items carefully to make sure no breakage or

damage occurred during shipping.

Do not discard the packing material until you have

carefully inspected and satisfactorily operated the snow

thrower.

PACKING LIST

- Snow Thrower

- Handle Assembly

- Chute Crank

- Chute Deflector

- Owner’s Manual

- Hardware bag

INSTALLING CENTER HANDLE

 Position the center handle and make sure the bracket

is pointed downward. (See Fig 1)

 Align the holes on the center handle with the holes in

the lower handle as shown. (See Fig 2)

 Insert J-bolt through both handles with the threaded

end at the bottom and facing inside. (See Fig 3)

 Install the handle knob and tighten securely to secure

the bolt in place. (See Fig 4)

 Repeat on the opposite side to secure the center

handle in place. (See Fig 5)

Fig. 1

Fig. 5

Fig. 4

Fig. 3

Fig. 1

Fig. 2

INSTALLING CHUTE CRANK

 Install the upper chute crank through the bracket

located on the center handle. (See Fig 8)

 Align the holes in the upper and lower cranks and

insert the cotter pin through the holes as shown to

secure. (See Fig 9 and Fig 10)

 Turn the lever left and right to verify the proper

functioning of the crank and the chute.

ASSEMBLY

7

Model SN75022

INSTALLING UPPER HANDLE

 Align the holes on the upper handle with the holes in

the center handle as shown. (See Fig 6)

 Insert threaded end of J bolt through both handles

with the threaded end facing inside.

 Install the handle knob and tighten secure.

 Repeat on the opposite side.

 Secure the cable clip to handles. (See Fig 7). Fig. 8

Fig. 9

Fig. 10

Fig. 7

Fig. 6

INSTALLING CHUTE DEFLECTOR

 Take the washer out of hardware bag. (See Fig 11)

 Position the washer onto the discharge chute. (See

Fig 12)

 Position the chute deflector over the discharge chute.

Align the holes and place the washer between the

deflector and chute. (See Fig 13)

 Tighten the knobs firmly. (See Fig 14 - 15)

Fig. 12

Fig. 11

ASSEMBLY

8

Model SN75022

Fig. 14

Fig. 15

Fig. 13

Position the discharge chute so that snow will discharge

in a safe direction. Do not direct the discharge towards

people or areas where property can be damaged. Keep

children, pets and others away for the work area. Do not

walk in front of the snow thrower when it is running.

Direct the discharge to the right or left by turning the

discharge chute with the chute crank. The chute can be

adjusted up to 180 degrees.

The chute deflector on the top of the discharge chute

controls the height of the discharge. Loosen both of the

knobs to raise or lower the deflector to the desired height

and tighten the knobs to secure the deflector.

NOTE: Do not over-tighten the knobs.

For the most efficient snow removal throw the snow

downwind and slightly overlap each swath.

Push the snow thrower forward at a comfortable rate of

speed, yet slow enough to clear the path completely. The

width and depth of the snow determines your forward

speed.

Start your clearing path near the electrical outlet and

work outward, throwing snow in a back and forth motion.

When turning at the end of a swath, step over the cord

and turn the snow thrower. Use the wheel on one side as

the pivot point. Slightly tilt the snow thrower on this pivot

point while turning.

The snow thrower can remove up to 12 inches deep in

one pass.

Clear snow often, before it gets too deep. It is best to

remove the snow as soon as possible after it falls.

Some parts of the snow thrower may freeze under

extreme temperature conditions. If parts freeze while the

snow thrower is in use, stop the snow thrower, unplug the

extension cord and inspect for frozen parts. Free all parts

of ice before restarting or operating the snow thrower. Do

not attempt to operate the snow thrower with frozen parts

or try to force controls that are frozen.

OPERATING

9

Model SN75022

Turning On and Off

WARNING: The auger starts rotating immediately

after the snow thrower is switched on. Keep hands and

feet away from the auger.

To switch ON, make sure the auger is not touching any

surface. Press down and hold the safety lock off button

(1). While holding down the button pull back on bail wire

(2). Once the snow thrower is started you can release the

safety lock off button.

To switch off simply release the bail wire.

LED HEADLIGHTS

LED headlights are located on the upper handle to

illuminate your path when using the snow blower in low

light conditions.

Power on the snow thrower, press on/off button to turn

the headlights on and off. (See Fig 16)

Removing snow

Before starting work, thoroughly inspect the area where

the equipment is to be used and remove all doormats

sleds, boards, wires and any other foreign objects.

Check the condition of the snow thrower before operating

it to ensure that the auger turns freely.

Check the auger for wear and tear at regular intervals.

Make sure all fasteners on the snow thrower (screws,

nuts, etc.) are fully tightened.

Fig 16

ON/ OFF BUTTON

OPERATING

After clearing the snow, continue to run the snow thrower

for a few minutes to prevent ice from freezing on moving

parts. Then switch off the motor, wait for all moving parts

to stop, and wipe the ice and snow from the snow

thrower with a clean rag.

WARNING: To avoid serious personal injury, do not

use hands or feet to unclog the chute.

Before unclogging the chute, shut off the snow thrower

and disconnect from the power supply. Wait for the auger

to stop turning. Clean out the chute with a wooden stick

such as a broom handle.

If the snow thrower should start to vibrate abnormally,

immediately stop the motor and check for the cause.

Vibration is generally a warning of trouble.

Look behind and use care when backing up with the

snow thrower.

For large areas a definite pattern of operation is required

to thoroughly clean an area of snow. These patterns

will avoid throwing snow in unwanted places as well as

eliminating a second removal of snow.

Pattern A: Throw the snow to the right or left side

where it is possible. For areas such as a long driveway

it is advantageous to start in the middle. Plow from one

end to the other, throwing snow to both sides.

Pattern B: If the snow can only be thrown to one side

of the area to be cleared, start on the opposite side.

Overload Protection

The over current protection will automatically turn off the

snow thrower when the circuit overloads. If the motor

stops, you can restart the snow thrower in 1 to 3 minutes.

10

Model SN75022

MAINTENANCE

Replacing the scraper

The scraper is located at the base of the snow thrower

beneath the auger housing.

Remove the screws that secure the scraper to the snow

thrower.

Install the new scraper and fasten it securely with the

screws. (See Fig 17)

Replacing the auger belt

Contact Earthwise for new belts and installation kit.

Under normal operating conditions it should not be

necessary to replace the auger belt. However, should the

auger jam or malfunction the belt could be damaged. To

replace the belt follow these instructions.

Belt drive system structure (See Fig 18)

11

Model SN75022

Regular cleaning and maintenance of your snow thrower

will ensure efficiency and prolong the life of the product.

Check all fasteners at frequent intervals for proper

tightness to be sure the snow thrower is in safe working

condition.

After each use, let the motor run for a few minutes so that

moving parts do not freeze. Then shut off the motor, wait

for all moving parts to stop, and wipe the ice and snow

from the snow thrower. Rotate the chute crank several

times to remove snow.

Only use a cloth soaked with hot water and a soft brush

to clean the snow thrower. Never wet or spray water on

the machine!

Do not use detergents or solvents as these could cause

irreparable damage to the snow thrower. Chemicals can

destroy the plastic parts.

To protect the snow thrower from corrosion when storing

for long periods, lightly oil the metal parts.

Store the snow thrower in a dry area out of reach of

children.

For the user’s safety, worn or damaged parts must be

replaced. Replace with original replacement parts only.

Parts from another snow thrower may not fit properly

causing an unsafe situation.

Lubricating the snow thrower

You do not need to lubricate the snow thrower. All of the

bearings are sealed and were lubricated at the factory for

the life of the snow thrower.

Replacing the rubber plates on auger

Detach the worn rubber plate by removing the two sets of

nuts, bolts, and washers used to secure it.

Install the new rubber plate.

Insert the bolt with the small flat washer into the

corresponding holes on each end of the rubber plate.

Use a large flat washer and locknut to secure the bolt

on each end.

Install the other rubber plate in the same manner.

Main Drive Belt

Auger Pulley

Auger Belt

Drive Pulley

Fig. 18

Fig 17

Before carrying out maintenance operations, disconnect power supply.

MAINTENANCE

1. Open the left side plate by removing three screws.

(Fig. 19)

2. Use your right hand to turn the rib side of the belt

up and pull upwards while turning the auger pulley

counterclockwise with your left hand. The belt can be

easily removed from the pulley. (Fig. 20 - 21)

12

Model SN75022

3. Put the belt on the drive pulley first and then place

the belt at the lower end of the auger pulley. (Fig. 22)

4. Use right hand to press the belt with ribbed side

down. (Fig. 23)

5. While holding the belt down with your right hand use

your left hand to turn the auger forward so that the

auger pulley rotates in a clockwise direction. (Fig. 24)

Fig. 21

Fig. 20

Fig. 22

Fig. 23

Fig. 24

Screw

Fig. 19

MAINTENANCE

6. Keep pressure on the belt with your right hand (rib

side down and flat side up) while rotating the auger.

The belt will be gradually pushed down onto the

pulley. When the belt is seated on the pulley, adjust

it so that the ribs of the belt match the grooves on

the pulley. (Fig. 25 - 28)

Fig. 25

13

Model SN75022

7. After belt is installed, replace the side plate and

secure it with the three screws. (Fig. 29)

Fig. 27

Fig. 26

Fig. 29

Fig. 28

Screws

Run the snow thrower for a few minutes to melt away any

snow on the snow thrower.

Disconnect the extension cord from the snow thrower.

Examine the extension cord thoroughly for signs of wear

or damage. Replace it if it is worn or damaged.

Examine the snow thrower thoroughly for worn, loose, or

damaged parts. Check connections and screws and

tighten if necessary. To repair or replace parts, contact

our customer service help line at 1-800-633-1501.

Store the snow thrower, along with the disconnected

extension cord, in a clean, dry place out of reach of

children. Cover loosely with a tarp for added protection.

STORAGE

TROUBLESHOOTING

Problem Possible causes Remedy

Motor does not start Unit not plugged in.

No electricity.

Defective cable.

Plug in the unit.

Check power supply.

Check cable. Repair or replace if required.

Poor results Drive belt worn or damaged.

Auger worn or damaged.

Discharge chute blocked.

Replace the drive belt.

Replace the rubber plates on auger. Ensure the screws

and nuts are properly tightened.

Switch off the snow thrower and clean the discharge chute.

Abnormal vibrations Drive belt worn or damaged.

Auger worn or damaged.

Scraper blade worn or damaged.

Replace the drive belt.

Replace the rubber plates on auger. Ensure the screws

and nuts are properly tightened.

Replace the scraper blade. Ensure the screws are proper-

ly tightened.

Motor shuts off during

operation Current too high Restart the snow thrower after 1 to 3 minutes.

14

Model SN75022

Call us first with questions about operating or maintaining your product at 1-800-633-1501

between 8:00 a.m. – 5:00 p.m. Eastern Standard Time, or get assistance on americanlawnmower.com.

CALL US FIRST !!

Call us first with questions about operating or maintaining your product at 1-800-633-1501

between 8:00 a.m. – 5:00 p.m. Eastern Standard Time, or get assistance on americanlawnmower.com.

SERVICE

For parts or service, please call 1-800-633-1501 or visit us online at americanlawnmower.com. Be sure

to provide all relevant information when you call or visit.

REPAIR PARTS

The model number of this tool is found on a plate or label attached to the housing. Please record the

serial number in the space provided below.

• NAME OF ITEM Snow Thrower

• MODEL NUMBER SN75022

• SERIAL NUMBER

CALL US FIRST !!

15

Model SN75022

Always mention the model number when ordering kits/items for this tool.

No. Kit/Item Number Description QTY

1 SN22-SB 22" Scraper Blade Kit 1

2 SN22-AK 22" Auger Kit 1

4 SN18-HWK-1 Hardware kit

1

5 SN18-ACK-1 Adjusting Cover Kit

1

6 SN2018-Belt Belt kit 1

7 WK-TC-SN Wheel Kit 1

8 SN18-CKH-1 Crank Handle Kit

1

3 SN18-CHK-1 Center Handle Kit 1

PARTS AND SERVICE

American Lawn Mower Company

The Great States Corporation

7444 Shadeland Station Way，

Indianapolis, IN 46256

Phone 1-800-633-1501

www.americanlawnmower.com

In a continued commitment to improve quality, the Manufacturer reserves the right to

make component changes or design changes when necessary.

OWNER’S MANUAL

SN75022 22-IN Corded Snow Thrower

Rev. 06/24/2021

WARRANTY POLICY

Two (2) year limited warranty on Earthwise outdoor power equipment.

Earthwise warrants to the original owner that each new product and service part is free from defects in

materials and workmanship and agrees to repair or replace any defective product or part for the warranty period

as stated above from the original date of purchase except for the conditions and circumstances listed below:

This warranty applies only to the original purchaser at

retail and may not be transferred.

Warranty applies if the product is used for personal,

household or family use. Warranty is void if product is

used for commercial, industrial or rental purposes.

Warranty does not include repairs necessary due to

operator’s abuse or negligence (including overloading

the product beyond capacity or immersion in water), or

the failure to assemble, operate, maintain or store the

product according to the instructions in the operator’s

manual.

This warranty is not transferable and

only applies to product sold directly

from an authorized retailer. This warranty

does not apply to any product, new or used, purchased

through unauthorized third-party channels.

ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL

LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT

FROM ANY DEFECT, FAILURE OR MALFUNCTION

OF THE PRODUCT IS NOT COVERED BY THE

WARRANTY. Some states do not allow the exclusion or

limitation on how long an implied warranty lasts, so the

above limitation may not apply to you.

Products sold damaged or incomplete, sold “as is”, or

sold as reconditioned are not covered under the warranty.

Damage or liability caused by shipping, improper

handling, improper assembly, incorrect voltage, improper

wiring, improper maintenance, improper modification or

the use of accessories and/or attachments not specifically

recommended is not covered by this warranty.

Expendable items that become worn during normal use

are not covered by the warranty.

Warranty does not cover damage caused by cold, heat,

rain, excessive humidity, corrosive environments and

materials, or other contaminants.

Warranty does not include installation, assembly or

normal adjustments explained in the owner’s manual.

The expense of delivering the product to the vendor and

the expense of returning the product or replacement parts

to the owner is not covered by the warranty.

The warranty does not cover normal deterioration of the

exterior finish, including but not limited to scratches,

dents, paint chips or any corrosion or discoloration

caused by heat, abrasive and chemical cleaners.

Proof of purchase, original dated sales receipt, must accompany all

warranty claims.

Modelo SN75022

MANUAL DEL OPERARIO

Lanzador de nieve con cable de

560 mm (22 pulg.)

Muchas gracias por su compra.

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE EL FUNCIONAMIENTO, EL

MONTAJE, LAS PIEZAS Y EL MANTENIMIENTO? IR A AMERICANLAWNMOWER.COM O LLAME AL

1-800-633-1501 ENTRE LAS 8:00 AM Y LAS 5:00 PM, HORA DEL ESTE DE LOS ESTADOS UNIDOS. DE

LOS ESTADOS UNIDOS.

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

Este producto fue diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de operación y seguridad

para el operario. Si se trata con cuidado, esta herramienta le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender

el manual del operario antes de usar este producto.

Instrucción de inicio rápido

De la pagina 9

Los productos eléctricos no se deben desechar junto con los residuos domésticos. Recicle

donde haya centros para tal fin. Consulte a la autoridad local o al distribuidor minorista para

obtener asesoramiento sobre reciclado.

SÍMBOLOS

Algunos de los siguientes símbolos pueden aparecer en este producto. Tenga a bien estudiarlos y aprender su significado.

La adecuada interpretación de estos símbolos le permitirá operar el producto mejor y de manera más segura.

2

Modelo SN75022

Precauciones para su seguridad.

PRECAUCIÓN: Lea el manual de instrucciones y atienda las instrucciones se seguridad y

advertencia.

PRECAUCIÓN: Retire el enchufe del tomacorriente de inmediato si el cable está dañado o cortado.

APAGUE la máquina, espere hasta que se detenga por completo y retire el enchufe del

tomacorriente antes de realizar alguna tarea de mantenimiento, limpieza o reparación.

PRECAUCIÓN: Use siempre protecciones para sus ojos y oídos.

Use calzado seguro, resistente y antideslizante.

¡PELIGRO! Pueden ser lanzados objetos a gran velocidad cuando el motor está en funcionamiento.

No pase delante de la máquina cuando está funcionando.

Mantenga a las personas que se encuentran en el lugar a una distancia segura.

¡PELIGRO! Cuchillas giratorias. Mantenga manos y pies a una distancia segura.

No colocar la mano debajo de la barrena.

Mantenga el cable eléctrico lejos de la barrena. La barrena puede dañar el cable y producir un contacto con

piezas activas.

No colocar la mano enfrente del deflector de descarga.

No exponga la unidad a la lluvia ni la use en lugares húmedos.

¡PELIGRO! Riesgos de descargas eléctricas.

No usar en la lluvia. No usar durante tormentas eléctricas.

PARA REDUCIR EL RIESGO DE LESIONES: Antes

de utilizar este producto, cerciórese de que todos

los usuarios lean y comprendan las instrucciones

de seguridad y la demás información incluida

en este manual.

PRECAUCIÓN: Use protección auditiva apropiada

mientras trabaja. En ciertas condiciones y con cierta

duración de uso, el ruido generado por este producto

puede contribuir a la pérdida de la audición.

Guarde estas instrucciones y revíselas con frecuencia

antes de usar la herramienta y para impartirlas a otros.

ADVERTENCIA: Al utilizar aparatos eléctricos,

se recomienda respetar siempre las precauciones

de seguridad básicas que se detallan a continuación,

a fin de reducir riesgos de incendios, descargas

eléctricas y lesiones personales.

LEA TODAS LAS INSTRUCCIONES

CONTROLE SI HAY PIEZAS DAÑADAS. Antes de seguir

usando el producto, se deberán revisar las piezas

dañadas en forma exhaustiva para determinar

si la herramienta funcionará correctamente y realizará

el trabajo previsto. Compruebe la alineación y las uniones

de las piezas móviles, el montaje, averías

de componentes y otros factores que puedan afectar

el funcionamiento. Se debe reparar o reemplazar

cualquier pieza dañada en forma adecuada. Para recibir

asistencia, comuníquese con nuestra línea de ayuda

de atención al cliente al 1-800-633-1501.

EVITE AMBIENTES PELIGROSOS. No trabaje

en entornos donde existan gases o sustancias explosivas.

Por lo general, los motores de estos productos producen

chispas que podrían inflamar los gases.

MANTENGA ALEJADOS A LOS NIÑOS. Todos

los visitantes, niños y mascotas deben mantenerse

a una distancia segura de la zona de trabajo.

USE ROPA ADECUADA. No use prendas sueltas

ni artículos de joyería. Use protección para cubrir y sujetar

el cabello largo, ya que puede quedar atrapado

en las piezas móviles.

Use calzado seguro, resistente y antideslizante.

En todo momento mantenga una buena base

de apoyo, especialmente en pendientes.

USE GAFAS DE SEGURIDAD. Al trabajar con este

producto, use gafas de seguridad con protectores

laterales que cumplan con la norma ANSI Z87.1.

DOBLE AISLAMIENTO. La sopladora de nieve tiene

doble aislamiento. Es decir que todas las piezas metálicas

externas están aisladas del suministro eléctrico.

Esto se logra con la introducción de una capa de

aislamiento entre las piezas eléctricas y las mecánicas.

El doble aislamiento garantiza la mayor seguridad posible.

ADVERTENCIA: Use cables de extensión para

exteriores rotulados con las siguientes inscripciones: SW-

A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, o

SJTOWA. Estos cables están especificados para usar al

aire libre y reducir el riesgo de descarga eléctrica.

ENCHUFES POLARIZADOS. Para reducir el riesgo

de descarga eléctrica, este producto tiene un enchufe

polarizado. Las conexiones polarizadas encajan

de una sola manera. Cerciórese de que el extremo

del receptáculo del cable de extensión tenga ranuras

de anchos diferentes para los contactos. Invierta

el enchufe si no encaja totalmente en el cable

de extensión. Si aún así no encaja, consiga un cable

de extensión adecuado. Si el cable de extensión no

se adapta bien al tomacorriente, llame a un electricista

competente para que instale un tomacorriente adecuado.

No modifique el enchufe de la herramienta ni el cable

de extensión de ningún modo.

CABLE DE EXTENSIÓN. Asegúrese de que el cable

de extensión esté en buenas condiciones. Además,

compruebe que tenga el grosor suficiente para

transportar la corriente que necesitará el producto.

Un cable de extensión muy pequeño provocará una

disminución en la tensión de la línea y, como resultado,

una pérdida de potencia y recalentamiento. La siguiente

tabla muestra el tamaño correcto que se debe usar

según la longitud del cable y el amperaje de la etiqueta.

Ante la duda, utilice el siguiente calibre más grueso.

Cuanto más bajo es el número de calibre, más grueso es el

cable.

Es posible unir dos cables

de extensión con un nudo para evitar

que se desconecten durante el uso.

Realice el nudo como se muestra

en la imagen y luego conecte

el enchufe del cable de alimentación

en el receptáculo del cable

de extensión.

Utilice una de las correas de sujeción del receptáculo o

Conectores descritos en este manual.

ADVERTENCIA: Mantenga todas las conexiones

secas y alejadas del suelo. No toque el enchufe

con las manos mojadas. De lo contrario, se pueden

producir lesiones personales graves o la muerte.

Tenga presente el cable de extensión mientras opera

la sopladora de nieve. Tenga cuidado de no tropezar con

el cable y manténgalo siempre alejado de la barrena.

ADVERTENCIAS DE SEGURIDAD IMPORTANTES

NORMAS GENERALES DE SEGURIDAD

3

Modelo SN75022

Calibre mínimo para los cables

Voltios Longitud total del cable en pies

120V 0-25 26-50 51-100 101-150

Amperaje

Más No más Calibre AWG

de de

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 No se recomienda

El funcionamiento de la sopladora de nieve en posición

manual no es seguro a menos que se utilice conforme

a las instrucciones especiales provistas en el manual

del operario.

PRECAUCIÓN: Nunca arroje nieve a las personas,

mascotas o automóviles y no permita que nadie

esté frente a la sopladora de nieve mientras está

en funcionamiento.

Es posible que los objetos que pueden tapar

la sopladora de nieve o causar daños estén escondidos

en la nieve. Antes de usar la máquina, despeje el área

de felpudos, trineos, tablas, cables y otros desechos.

Si la barrena golpea un cuerpo extraño, detenga

la sopladora de nieve y verifique que no haya signos

de daños. Haga las reparaciones necesarias antes

de volver a empezar y continuar el trabajo.

PONGA ATENCIÓN. Observe lo que está haciendo.

Use el sentido común. No opere la sopladora de nieve

si está cansado o bajo la influencia de drogas,

alcohol o medicamentos.

Si la sopladora de nieve comienza a vibrar de manera

inusual, apáguela de inmediato y revísela para

detectar la causa. Generalmente, la vibración advierte

la existencia de un problema.

Antes de realizar tareas de mantenimiento

o reparaciones, apague la herramienta, desconéctela

del suministro eléctrico y espere hasta que la barrena

se detenga por completo.

Nunca opere la sopladora de nieve si los protectores

adecuados y otros dispositivos de protección no están

en su lugar y en buenas condiciones.

Al efectuar el mantenimiento, use sólo repuestos

idénticos.

PRECAUCIÓN: La barrena no se detiene de

inmediato cuando se apaga la sopladora de nieve.

PRECAUCIÓN: Riesgo de lesiones. La sopladora

de nieve puede provocar lesiones graves. No acerque

ninguna parte de su cuerpo, ni prendas de vestir

a la barrena giratoria.

ADVERTENCIA: Proposición 65 de California:

Este producto contiene sustancias químicas al estado

de California como causantes de cáncer, defectos de

nacimiento u otros problemas reproductivos.

ADVERTENCIA: Cáncer y Daño

Reproductivo - www.P65Warnings.ca.gov.

INTERRUPTOR DE CIRCUITO POR FALLA A TIERRA

(ICFT). El circuito o tomacorriente que se usen para

la sopladora de nieve deben contar con esta protección.

Se pueden utilizar receptáculos que tengan la protección

de ICFT incorporada.

ADVERTENCIA: Nunca coloque las manos cerca

de la barrena para quitar nieve, palos u otros desechos.

Al limpiar la barrena, esta puede destrabarse

repentinamente y provocar lesiones, aún cuando

la sopladora de nieve se haya detenido. Para destapar

una obstrucción, use siempre un palo de madera como

el del mango de una escoba.

DESCONECTE LA UNIDAD del suministro eléctrico

cuando no esté en uso o durante el servicio

de mantenimiento o la limpieza. No deje la herramienta

sin vigilancia.

NO MALTRATE EL CABLE. Nunca tire del cable para

trasladar este producto ni para desconectarlo

del receptáculo. Aleje el cable del calor, el aceite

y los bordes filosos.

USE LA HERRAMIENTA CORRECTA. No utilice este

producto en trabajos para los que no esté indicado.

NO SOBRECARGUE la sopladora de nieve usándola

a una velocidad excesiva. La máquina funcionará

mejor y de manera más segura a la velocidad para

la que fue diseñada.

NO ADOPTE UNA POSTURA INCÓMODA. Guíe

la sopladora de nieve sólo a paso de hombre.

Mantenga una base de apoyo firme y buen equilibrio

en todo momento.

ILUMINACIÓN. Trabaje con la sopladora de nieve sólo

con luz natural o buena luz artificial.

GUARDE LA UNIDAD BAJO TECHO. Cuando no esté

en uso, la sopladora de nieve se deberá guardar en un

lugar seco, fuera del alcance de los niños.

MANTENGA LA UNIDAD EN CONDICIONES.

Consérvela limpia para lograr un óptimo funcionamiento y

reducir el riesgo de lesiones. Revise el cable de extensión

periódicamente y reemplácelo si está dañado. Mantenga

los mangos secos, limpios y libres de aceite.

Para un funcionamiento seguro, no utilice la sopladora

de nieve en pendientes demasiado pronunciadas.

Cuando trabaje en pendientes, disminuya la velocidad

y asegúrese de tener una buena base de apoyo.

Antes de encender la sopladora de nieve, cerciórese

de que la barrena no esté en contacto con ningún objeto

y de que tenga libre movimiento.

No intente limpiar la nieve en una superficie de grava

o de roca triturada. Este producto está diseñado sólo para

usar sobre superficies rígidas y planas sin arena, piedras

y desechos, cables o cualquier otro objeto.

NORMAS GENERALES DE SEGURIDAD

4

Modelo SN75022

La page charge ...

EarthWise SN75022 Mode d'emploi

EarthWise SN75022 Mode d'emploi

dans d''autres langues

Documents connexes