Hathaway BG2015 Manuel utilisateur

Marque: Hathaway

Modèle: BG2015

Taper: Manuel utilisateur

8' HOT S

HOT ARCADE BALL TABLE

ASSEMBLY INSTRUCTIONS

NG2015

Please Do Not Hesitate to

Contact Our Consumer Hotline

800-759-0977

with

Any Questions That May

Arise During

Assembly or

Use of This Product!

Ver. 1116

THANK YOU!

Thank you for purchasing this product. We work around the clock and around the globe to ensure

that our products maintain the highest possible quality. However, in the rare case of issues during

assembly or use of this product, please contact our Consumer Hotline at 800-759-0977 for immediate

assistance before contacting your retailer. Please read the warranty information at the back of these

assembly instructions for further details.

CARE AND USE

1. This

product is intended for INDOOR use only.

2. Do NOT drag the table when moving it, as this will damage the legs.

ASSEMBLY TIPS

1. Find a clean, level surface to begin the assembly of your game table. We recommend that two adults

work together to assemble this game. You may want to carefully cut or tear the four corners of the box

so that the bottom of the box can be used as your work surface.

2. Remove all of the contents from box and verify that you have all of the parts shown on the Parts

List before you begin assembly. Note: Some parts may be pre-installed or pre-assembled.

3. Some figures or drawings may not look exactly like product.

4. When installing parts that have more than one screw or bolt, hand tighten all screws or bolts

in place before final tightening with screwdriver or wrench.

5. Electric screwdrivers may be helpful during assembly; however, please set a low torque and use

extreme caution because screws may be stripped or overtightened, resulting in damaged parts, if the

electric screwdriver’s torque is set too high.

WARNINGS!

READ AND FOLLOW ALL ASSEMBLY, OPERATION AND SAFETY INSTRUCTIONS CAREFULLY.

CHOKE HAZARD - THIS ITEM MAY CONTAIN SMALL BALLS AND PARTS

NOT SUITABLE FOR CHILDREN UNDER 3 YEARS OF AGE.

IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS

IN ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT.

8’ HOT SHOT ARCADE

BALL TABLE - NG2015

Parts List

PARTS

P1L NGP5856

P1R NGP5857 P2L NGP5858 P2R NGP5859 P3L NGP5860 P3R NGP5861 P4 NGP5862

P5 NGP5863 P6L NGP5864 P6R NGP5865 P7L NGP58661 P7R NGP58671 P8 NGP5868

FRONT END

APRION

P9 NGP5870

P10 NGP5871

P11 NGP5872 P12 NGP5873 P13 NGP5874

BACK UPPER

PANEL

LEFT FRONT LEG

RIGHT BACK

LEG

FRONT BOTTOM

PANEL

LEFT BACK LEG

SPREADER

LEFT FRONT

SIDE APRON

LEFT BACK

SIDE APRON

RIGHT BACK

SIDE APRON

CROSSBEAM

NET FRAME

FRONT

FRONT TOP

PANEL

CONNECT HINGE

SET

BACK BOTTOM

PANEL

P16 NGP5877

TARGET BOARD

P14 NGP5875

BACKBOARD

P15 NGP5876

ELECTRONIC

SCORER

7/15

P17 NGP5878

P18 NGP5879 P19 NGP5880 P20 NGP5881

NET

NET FRAME

BACK

P21 NGP5882

NET SPACER

BAR

RIGHT FRONT

LEG

LEFT MIDDLE

LEG

RIGHT MIDDLE

LEG

RIGHT FRONT

SIDE APRON

P23 NGP58831P22 NGP5884

SUPPORT PANEL

BALL

“L” SUPPORT

PANEL

P24 NGP58851 A1 NGP5886

P13

P17

P15

P7R

P6R

P6L

P24

P3L

P2L

P1L

P11

P1R

P16

P10

P2R

P3R

P14

P20

P18

P19

P23

RESET SWITCH

NGP5888

RUBBER

GEAR HINGE

NGP5890

REAR APRON

TRIANGULAR

INSERT

P7L

NGP58761*

TARGET BOARD

WIRING HARNESS

NGP58762*

TARGET BOARD

FLIP SWITCH

*Pre-assembled

on Target Board

P25 NGP5885

COVER PANEL

Illustrations Not to Scale

For replacement parts please call 800-759-0977.

H1 H2 H3 H4 H5 H6

5/16” BOLT

5/16” WASHER

1-1/4” SCREW

ADDITIONAL EQUIPMENT

REQUIRED:

PHILLIPS HEAD

SCREWDRIVER

H11 T1

ALLEN WRENCH

1/4” FLAT

WASHER

1/4”X1-1/4” BOLT

1/4”X1” BOLT

1/4” FLAT

WASHER

3/4” SCREW

3/8” SCREW

3/4” FLAT

SCREW

HARDWARE PACK - NGP5887

T2 NGP58763

POWER

ADAPTER

H10

1-1/4” FLAT

SCREW

7/15

Illustrations Not to Scale

ASSEMBLY INSTRUCTIONS

Unfinished Side Up

Black Side Down

P10

P21

Figure 1

1. Find a clean, level place to begin the assembly of your game. We recommend building the unit on the shipping carton to

protect the parts during assembly. Note: The two main units are assembled upside down then turned over for final assembly.

2. Attach the SUPPORT PANEL, P21, to the FRONT BOTTOM PANEL, P10, using (3) SCREWS, H8, through the two

outer holes as shown in Figure 1. Note: The P10 panel and P21 support panel both have pre-drilled holes for screws.

3. Place the LEFT FRONT SIDE APRON, P6L, and RIGHT FRONT SIDE APRON, P6R, upside down and approx. 2 feet

apart, as shown in Figure 2.

4. Insert FRONT TOP PANEL, P9, with finished white side down, into lower grooves of SIDE APRONS, P6L and P6R.

Make sure the end of P9 with the cutouts is on the same end as gear hinge as shown in Figure 2. Slide P9 forward until

the end with cutouts is flush with SIDE APRON ends above gear hinges. With help from another adult, hold this assembly

firmly and attach pieces together using (2) SCREWS, H1, and pre-drilled holes on each side.

5. Attach FRONT END APRON, P5, with groove facing in, using (2) SCREWS, H1, and pre-drilled holes on each side.

Note: Don’t tighten screws all the way until you complete Step 6. This will make it easier to get P10 into P5 groove.

6. Insert FRONT BOTTOM PANEL, P10, with unfinished side up, into upper grooves of SIDE APRONS, P6L and P6R.

Slide P10 forward until the end is flush with SIDE APRON ends above gear hinges, even with panel P9. Tighten P5 Screws.

Note: This unit is assembled

upside down.

P6L

Note: Location

of gear hinge

P6R

Note: Location

of gear hinge

Note: Location

of these cutouts

P10

Unfinished

Side Up

Slide both

panels in grooves

White

Side Down

Figure 2

7. Attach CROSSBEAM, P8, with cutout opening facing down and to the left, using (2) SCREWS, H1, and pre-drilled

holes on each side, as shown in Figure 3.

8. Attach LEFT and RIGHT FRONT LEGS, P1L and P1R, using (2) BOLTS, H2, and (2) WASHERS, H3, on each leg, as

shown in Figure 3. Note: Hand tighten for now, and then do final tightening with ALLEN WRENCH, T1, once P4 Spreader

is attached in next step.

9. Attach SPREADER, P4, using (4) SCREWS, H1, as shown in figure 3. Note: Hand place screws in all four pre-drilled

holes to align panel before tightening.

CAUTION:

P4 SPREADER MUST BE CENTERED

CORRECTLY ONTO PRE-DRILLED HOLES

IN LEGS BEFORE ATTACHING WITH H1

SCREWS.

Figure 3

NOTE: Location

of gear hinge

P1L

P1R

ASSEMBLY INSTRUCTIONS (CONT.)

10. Attach the SUPPORT PANEL, P21, to the FRONT BOTTOM PANEL, P10, using (3) SCREW, H8, through the

three holes as shown in Figure 4. Note: The P12 panel and P21 support panel both have pre-drilled holes for screws.

Unfinished Side Up

Black Side Down

P12

P21

Figure 4

Figure 5

THANK YOU!ASSEMBLY INSTRUCTIONS (CONT.)

P7L

P7R

P23

11. Attach REAR APRON, P23,and CROSSBEAM, P8, to the LEFT BACK SIDE APROS,P7L, and RIGHT BACK SIDE

APROS, P7R using (4) SCREW, H1 as shown in Figure 5.

Figure 6

ASSEMBLY INSTRUCTIONS (CONT.)

Slide both

panels in grooves

Note: Location

of gear hinge

Note: Location

of these cutouts

P12

P11

12. Insert BACK BOTTOM PANEL, P12, with unfinished side down, into lower grooves of SIDE APRONS, P7L and P7R.

Slide P12 forward until the end is flush with SIDE APRON ends below gear hinges, as shown in Figure 6.

White side up

13. Insert BACK TOP PANEL, P11, with finished white side up, into upper grooves of SIDE APRONS, P7L and P7R.

Make sure the end of P11 with the cutouts is on the same end as gear hinge as shown in Figure 6. Slide P11 forward until

the end with cutout is flush with SIDE APRON ends above gear hinges. With help from another adult, hold this assembly

firmly and attach pieces together using (3) SCREWS, H1, and pre-drilled holes on each side.

P7L

P7R

ASSEMBLY INSTRUCTIONS (CONT.)

Figure 7

14. Assemble LEFT and RIGHT MIDDLE LEGS, P2L and P2R, together with SPREADER, P4, using (4) SCREWS, H1,

as shown in Figure 7. Note: Hand place screws in all four pre-drilled holes to align panel before tightening. Attach “L”

SUPPORT PANEL, P22, in same manner using (6) SCREWS, H10, as shown.

15. Attach Middle Leg Assembly between assembled sides, P7L and P7R, using (2) BOLTS, H2, and (2) WASHERS, H3,

on each leg, as shown in Figure 7. Note: Velcro will be used as wire harness in future step.

16. Attach LEFT and RIGHT BACK LEGS, P3L and P3R, using (2) BOLTS, H2, and (2) WASHERS, H3, on each leg, as

shown in Figure 7. Note: Hand tighten for now, and then do final tightening with ALLEN WRENCH, T1, once P4 Spreader

is attached in next step.

17. Attach SPREADER, P4, between Legs using (4) SCREWS, H1, as shown in Figure 7.

Note: Hand place screws in all four pre-drilled holes to align panel before tightening.

CAUTION:

P4 SPREADER MUST BE CENTERED

CORRECTLY ONTO PRE-DRILLED HOLES

IN LEGS BEFORE ATTACHING WITH H1

SCREWS.

P3L

P3R

Note: Correct location

Velcro

P22

H2 H3

P2L

P2R

H10

P22

of Support Panel to Legs

ASSEMBLY INSTRUCTIONS (CONT.)

Figure 8

H5 Bolt

Washer

P15

Note: Hinge Gear Assemblies Must Mesh

Note: This Hinge is Threaded and Must Be on Inside

CAUTION:

Pinch Point

CAUTION:

Pinch Point

Reset Button

Reset

Button

No Gap

Ligature

Bundle of

White Wire

P16

Hinge Set

P16

Hinge Set

P7R

Back Side

Apron

P6R

Front Side

Apron

Note: This Hinge is NOT Threaded

and Must Be on Outside

Washer

18. With the help of another adult, set both completed assemblies upright and position so gears face each other as shown

in Figure 8. Using (2) HINGE SETS, P16, connect assemblies using BOLT, H5, and Washer, H7, as shown in Figure 8.

The bolts should be snug, but NOT over tightened as this is a pivot area. Note: Hinge gear assemblies must mesh together,

per diagram, and there should be no gap between playfields. Also, only one hinge plate per set is threaded and must be

installed on the inside of each playfield side.

20. Place TARGET BOARD, P15, with red hole at the top, into position with the sides resting in the grooves of the braces

on the side panels and against the front of the ramp.

21. Attach the RESET BUTTON, with the long white wire, through the hole in the FRONT END APRON, P5, by removing

the washer and nut on the back of the Reset Button, feeding the Reset Button and wire through the hole from the front and

re-attaching the washer and nut. Note: Be careful not to damage or break wire connections while attaching Reset Button.

Reset Button -

(this ships

pre-wired to

Target Board)

P24

19. Attach TRIANGULAR PATCH, P24, on each side aprons using (2) BOLTS, H4, and (2) WASHERS, H6, on each patch,

as shown in Figure 8.

ASSEMBLY INSTRUCTIONS (CONT.)

22. Feed the long white wire through the cutouts in all CROSSBEAMS, P8, and the Velcro on P22, toward the

back and up through the hole in the BACK BOTTOM PANEL, P12. This will connect to the short white wire on the wiring

harness.

23. Feed the Target Board’s Wiring Harness through the round hole in the BACKBOARD, P13, and attach the Backboard

between the TTRIANGLE PATCH using (4) SCREWS, H1, as shown in figure 9. Note: Hand place screws in all four

pre-drilled holes to align panel before tightening.

24. Attach ELECTRONIC SCORER, P14, to Backboard using (4) SCREWS, H9, as shown. Connect the Wiring Harness

from the Electronic Scorer to the Target Board’s Wiring Harness.

26. Plug in the AC Power Adapter (DO NOT use batteries with adapter), or install four (4) “AA” batteries (not included),

into the backside of the Electronic Scorer, P14. Remove protective plastic film from face of Electronic Scorer.

P14

Figure 9

P13

H11

P25

25. Attach COVER PANEL, P25, over Wiring Harness and to Backboard using (4) SCREWS, H11, as shown in Figure 9.

FINAL SET-UP & HOW TO PLAY

1. Using two adults, set the unit in a suitable location in your game room.

2. Plug in the AC Power Adapter (DO NOT use batteries with adapter), or install four (4) “AA”

batteries (not included), into the backside of the Electronic Scorer, P14

3. Turn the power switch to the ON position.

4. When all “zeroes” are showing on the score board, press the reset button on the front of the

unit. You are now ready to play.

5. Each player rolls six (6) balls per game trying to reach the highest score. If a ball is rolled

and it doesn’t score, you may roll that ball again. The player with the highest score wins.

6. After both players have rolled their six balls, press the Reset Button to play again.

7. Turn the power OFF when not in use.

CAUTION: DO NOT THROW the ball at the target board as this may cause damage to the

game. The correct and safe way is to always ROLL the ball along the runway.

P17

Net

P20

Spacer Bars

P19

Frame

Back

(Smaller)

P18

Frame

Front

(Larger)

ASSEMBLY INSTRUCTIONS (CONT.)

Figure 10

27. Loosely attach NET FRAME FRONT, P18, and NET FRONT BACK, P19, to the Back Side Aprons and Triangle Patch

using (4) BOLTS, H4, and WASHERS, H6, through the eye hole at the bottom of the frames.

28. Attach (2) NET SPACER BARS, P20, between the Front and Back Frames, on either side, by inserting the curved

ends into the frame receptacle as shown in Figure 10.

29. Drape the NET, P17, over the frame with the longest side, and corner rivets, running side to side. The net will angle

down toward the front. Now remove Bolts loosely attached in Step 27, one at a time, and re-insert Bolt through Corner

Rivets and back through Frame Eye Hole until all four are securely attached. Use Velcro on Net to secure Net to Frame.

180-DAY LIMITED WARRANTY

This product is warranted to the original purchaser to be free from defects in material or workmanship

for a period of 180 days from the date of the original retail purchase.

This warranty does not cover defects or damage due to improper installation, alteration, accident or

any other event beyond the control of the manufacturer. Defects or damage resulting from misuse,

abuse or negligence will void this warranty. This warranty does not cover scratching or damage that

may result from normal usage.

This product is not intended for institutional or commercial use; the manufacturer does not assume

any liability for such use. Institutional or commercial use will void this warranty.

This warranty is nontransferable and is expressly limited to the repair or replacement of the defective

product. During the warranty period, the manufacturer shall repair or replace defective parts at no

cost to the purchaser. Shipping charges and insurance are not covered and are the responsibility of

the purchaser. Labor charges and related expenses for removal, installation or replacement of the

product or components are not covered under this warranty.

The manufacturer reserves the right to make substitutions to warranty claims if parts are unavailable

or obsolete.

The manufacturer shall not be liable for loss of use of the product or other consequential or incidental

costs, expenses or damages incurred by the consumer of any other use. The user assumes all risk of

injury resulting from the use of this product.

This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of

. Neither the manufac-

turer nor any of its representatives assumes any other liability in connection with this product.

All warranty claims must be made through the retailer where the product was originally

purchased. A purchase receipt or other proof of date of purchase will be required to process

all warranty claims. The model number and part numbers found within the assembly

instructions will be required when submitting any parts requests or warranty claims.

For further warranty information or inquiries, please call 800-759-0977

Ver. 1116

TABLE DE BALLON D'ARCADE

HOT SHOT 2,43 m

INSTRUCTIONS D’ASSEMBLAGE

NG2015

Contactez

notre

service à la clientèle au

800-759-0977

avec des questions sur le montage

ou l'utilisation de ce produit.

MERCI!

Merci d’avoir acheté notre produit. Nous travaillons 24 heures sur 24, partout dans le monde, à garantir

que nos produits sont de la meilleure qualité possible. Toutefois, dans les rares cas de problèmes lors

du montage ou de l'utilisation de ce produit, se il vous plaît communiquer avec notre service à la clientèle

au 800-759-0977 pour une aide immédiate avant de contacter votre revendeur. Pour obtenir de plus amples

renseignements, veuillez lire l'information relative à la garantie au verso de ce guide d’instructions.

ENTRETIEN ET USAGE

1. Ce produit doit être utilisé À L’INTÉRIEUR seulement.

2. NE JAMAIS déplacer la table en la traînant, cela pourrait endommager

les pieds.

INSTRUCTIONS D’ASSEMBLAGE

1. Trouver une surface propre et plane, pour commencer le montage de votre table de jeu. La table

s’assemble à l’envers pour être ensuite retournée sur ses pieds, une fois l’assemblage complété.

Cette table est lourde et nécessite au moins deux adultes forts pour la soulever et la retourner.

2. Retirez le contenu de la boîte, avant de commencer l’assemblage, assurez-vous d’avoir toutes

les pièces telles que listées et illustrées au tableau d’identification. Avis : certaines pièces sont

préassemblées ou préinstallées.

3. Certaines illustrations ou dessins peuvent ne pas ressembler au produit que vous avez acheté.

4. Quand vous fixez en place une pièce avec plus d’une vis ou écrou, veuillez, en premier, les

visser à la main et terminer la fixation avec un tournevis ou une clé.

5. Un tournevis électrique peut être utile lors de l’assemblage, mais veuillez le régler à basse torque

et l’utiliser avec prudence; si la torque est trop élevée, la vis peut se défaire ou être trop serrée.

AVERTISSEMENTS!

LIRE TOUTES LES INSTRUCTIONS D’ASSEMBLAGE ET LES CONSIGNES DE SÉCURITÉ ATTENTIVEMENT.

RISQUE D’ÉTOUFFEMENT – CERTAINS ÉLÉMENTS DU PRODUIT CONTIENNENT

DE PETITES PIÈCES - NE CONVIENT PAS À UN ENFANT DE MOINS DE TROIS ANS.

IMPORTANT! VEUILLEZ LIRE, EN ENTIER, TOUTES LES

INSTRUCTIONS AVANT D’ASSEMBLER VOTRE PRODUIT.

TABLE DE BALLON D'ARCADE HOT SHOT 2,43 m - NG2015

Liste des pièces

PIED

GAUCHE AVANT

ÉCARTEUR

PIED

DROIT AVANT

PIED

GAUCHE CENTRE

PIED

DROIT CENTRE

PIED

GAUCHE ARRIÈRE

PIED

DROIT ARRIÈRE

TABLIER AVANT

TABLIER

GAUCHE AVANT

TABLIER

AVANT DROIT

TABLIER

ARRIÈRE GAUCHE

TABLIER

ARRIÈRE DROIT

TRAVERSE

PANNEAU

SUPÉRIEUR AVANT

PANNEAU

INFÉRIEUR AVANT

PANNEAU

SUPÉRIEUR ARRIÈRE

PANNEAU

INFÉRIEUR ARRIÈRE

PANNEAU

ARRIÈRE

MARQUEUR

ÉLECTRONIQUE

PANNEAU CIBLE

ENSEMBLE

DE CHARNIÈRE

FILET

CADRE

AVANT FILET

CADRE

ARRIÈRE FILET

ÉCARTEUR

POUR FILET

PANNEAU

DE SOUTIEN

TABLIER ARRIÈRE

PANNEAU DE

SOUTIEN EN ῝L῝

INSÉRER

TRIANGULAIRE

BALLON

VITESSE

CHARNIÈRE

COMMUTATEUR DE

RÉINITIALISATION

P1L NGP5856

P1R NGP5857 P2L NGP5858 P2R NGP5859 P3L NGP5860 P3R NGP5861 P4 NGP5862

P5 NGP5863 P6L NGP5864 P6R NGP5865 P7L NGP58661 P7R NGP58671 P8 NGP5868 P9 NGP5870

P10 NGP5871

P11 NGP5872 P12 NGP5873 P13 NGP5874

P16 NGP5877

P14 NGP5875

P15 NGP5876

P17 NGP5878

P18 NGP5879 P19 NGP5880 P20 NGP5881 P21 NGP5882

P23 NGP58831P22 NGP5884

P24 NGP58851 P25 NGP5885

P13

P17

P15

P7R

P6R

P6L

P24

P3L

P2L

P1L

P11

P1R

P16

P10

P2R

P3R

P14

P20

P18

P19

P23

P7L

PIÈCES

7/15

*pré-assemblé sur panneau cible

FAISCEAU DE CÂBLAGE INTERRUPTEUR BASCULE

PANNEAU CIBLEPANNEAU CIBLE

A1 NGP5886 NGP5888 NGP5890 NGP58761* NGP58762*

PANNEAU DE

COUVERTURE

illustrations non à l'échelle

Pour commander une pièce de remplacement,

veuillez téléphoner au 1 800 759-0977

H1 H2 H3 H4 H5 H6

VIS 3,1 cm

H11 T1

TROUSSE DE QUINCAILLERIE – NGP5887

BOULON 0,79 cm RONDELLE 0,79 cm

BOULON

3,1 cm x 0,64 cm

BOULON

2,5 cm x 0,64 cm

RONDELLE

PLATE 0,64 cm

RONDELLE

PLATE 0,64 cm

VIS 1,90 cm VIS 0,95 cm VIS 1,8 cm

CLÉ HEXAGONALE

TOURNEVIS

CRUCUFORME

ÉQUIPEMENT

ADDITIONNEL REQUIS :

T2 NGP58763

ADAPTATEUR

SECTEUR

H10

VIS 3,18 cm

7/15

illustrations non à l'échelle

Pour commander une pièce de remplacement,

veuillez téléphoner au 1 800 759-0977

INSTRUCTIONS D’ASSEMBLAGE

Côté non fini vers le haut

Côté noir en dessous

P10

P21

Figure 1

1. Commencez d’assembler votre table de jeu dans un lieu propre et lisse et de niveau. Il est conseillé de le monter sur les

cartons d’expédition afin de ne pas abîmer les pièces lors de l’assemblage. Avis : Les deux structures principales sont

assemblées à l’envers et ensuite retournées pour terminer l’assemblage.

2. Fixez le PANNEAU DE SUPPORT (P21) au PANNEAU INFÉRIEUR AVANT (P10) en insérant trois VIS (H8) dans les

ouvertures extérieures tel qu’illustré à la Figure 1. Avis : le panneau (P10) et le panneau de support (P21) sont dotés de

trous prépercés pour y insérer les vis.

3. Placez le TABLIER LATÉRAL GAUCHE AVANT (P6L) et le TABLIER LATÉRAL DROIT AVANT (P6R) à l’envers, à

environ 65 cm de distance tel qu’illustré à la Figure 2.

4. Insérez le PANNEAU SUPÉRIEUR AVANT (P9), côté blanc en dessous, dans les rainures inférieures du TABLIERS

LATÉRAL GAUCHE AVANT (P6L) et du TABLIER LATÉRAL DROIT AVANT (P6R). Assurez-vous que les entailles

situées à l’extrémité du panneau P9 soient sur le même côté que la charnière tel qu’illustré à la Figure 2. Faites glisser le

panneau P9 jusqu’à ce que les entailles affleurent les extrémités du TABLIER LATÉRAL par-dessus les charnières. Avec

l’aide d’un adulte, retenez fermement cet assemblage et fixez les pièces ensemble et insérez deux VIS (H1) dans les

ouvertures pré-percées situées sur chacun des côtés.

5. Fixez le TABLIER D’EXTRÉMITÉ AVANT (P5) avec les rainures orientées vers l’intérieur insérez deux VIS (H1) dans

les ouvertures pré-percées situées sur chacun des côtés. Avis : Ne pas serrer les vis complètement jusqu'à ce que vous

accomplissez l’étape 6. Cela facilitera l’insertion du panneau P10 dans les rainures du tablier P5.

6. Insérez le PANNEAU INFÉRIEUR AVANT (P10), avec le côté non fini vers le haut, dans les rainures supérieures du

TABLIER LATÉRAL (P6L) et du TABLIER LATÉRAL (P6R). Faites glisser le panneau P10 vers l’avant jusqu’à ce que les

extrémités affleurent le TABLIER LATÉRAL par-dessus les charnières, égalisez à l’aide du panneau P9. Serrez les vis P5.

Avis : cette table de jeu

s’assemble à l’envers.

P6L

Avis : emplacement

de la charnière

P6R

Avis : emplacement

de la charnière

Avis : emplacement

des entailles

P10

Côté non fini

vers le haut

Insérer les deux

panneaux dans

les rainures

Côté blanc

en-dessous

Figure 2

7. Fixez la TRAVERSE (P8), avec les entailles orientées vers le bas à gauche à l’aide de deux VIS (H1) et des ouvertures

pré-perforées situées sur chacun des côtés, tel qu’illustré à la Figure 3.

8. Fixez le PIED GAUCHE AVANT (P1L) et le PIED DROIT AVANT (P1R) à l’aide de deux BOULONS (H2) et de RON-

DELLES (H13) pour chaque pied, tel qu’illustré à la Figure 3. Avis : pour l’instant, serrez les boulons manuellement et

complétez le serrage à l’aide de la CLÉ HEXAGONALE (T1) dès que l’espaceur (P4) est fixé à la prochaine étape.

9. Fixez l’ÉCARTEUR (P4) à l’aide de quatre VIS (H1), tel qu’illustré à la figure 3. Avis : insérez manuellement les vis à

l’intérieur des quatre ouvertures pré-perforées et alignez le panneau avant de serrer.

Figure 3

Avis : emplacement

de la charnière

P1L

P1R

ATTENTION:

ÉCARTEUR (P4) DOIT ÊTRE BIEN CENTRÉ

CORRECTEMENT DANS DES TROUS

PRÉ-PERCÉS DANS DES JAMBES AVANT

AVANT VIS DE FIXATION (H1).

INSTRUCTIONS D’ASSEMBLAGE (suite)

10. Fixez la PANNEAU DE SUPPORT (P21) au PANNEAU INFÉRIEUR AVANT (P10) à l’aide trois VIS (H8) à travers les

trois trous comme illustré à la Figure 4. Avis : le panneau P12 et le PANNEAU DE SUPPORT (P21) sont dotés d’ouvertures

pré-perforées pour les vis.

Côté non fini

vers le haut

Côté noir

en-dessous

P12

P21

Figure 4

Figure 5

P7L

P7R

P23

11. Fixez TABLIER ARRIÈRE, P23, et TRAVERSE, P8, aux TABLIER ARRIÈRE GAUCHE, P7L, et TABLIER

ARRIÈRE DROIT, P7R, utilisant (4) VIS, H1, comme illustré à la Figure 5.

THANK YOU!INSTRUCTIONS D’ASSEMBLAGE (suite)

La page charge ...

Hathaway BG2015 Manuel utilisateur

Marque: Hathaway

Modèle: BG2015

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Hathaway BG2015 User manual

Hathaway BG2015 Manuel utilisateur

Hathaway BG2015 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents