TEAC AP-505 Le manuel du propriétaire

Marque: TEAC

Modèle: AP-505

Catégorie: Équipement musical supplémentaire

Taper: Le manuel du propriétaire

D01343221A

AP-505

Stereo Power Amplifier

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

ENGLISH

FRANÇAIS

ESPAÑOL

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete

outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the manufac-

turer, or sold with the apparatus. When a

cart is used, use caution when moving the

cart/apparatus combination to avoid injury

from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume)

from earphones or headphones can cause hearing loss.

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batter-

ies: there is danger of explosion if a battery is replaced with

an incorrect type of battery. Replace only with the same or

equivalent type.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

IN USA/CANADA, USE ONLY ON 120V SUPPLY.

The nameplate is located on the bottom of the unit as shown below.

Front side

Nameplate

IMPORTANT SAFETY INSTRUCTIONS (continued)

Model for USA

Supplier’s Declaration of Conformity

Responsible party:

Pioneer & Onkyo U.S.A. Corporation

Address: 22828 Lockness Avenue, Torrance, CA90501 U.S.A.

Telephone number: 1-201-785-2600

This device complies with Part.15 of FCC Rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Information

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the equipment and/or the receiving

antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

Model for Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

This product complies with the European

Directives request, and the other Commission

Regulations.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/

accumulators should be disposed of separately from the

municipal waste stream via collection facilities designated by

the government or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valuable

resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC, 2013/56/EU), then the chemical symbols

for those elements will be indicated beneath the

WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

, Hg,

Company names and product names in this document are the trademarks or registered trademarks of their respective owners.

Contents

Check to be sure the box contains all the included items shown

below.

Please contact the store where you purchased this unit if any

of these items are missing or have been damaged during

transportation.

Power cord × 1

Rubber pads × 3

Owner’s manual (this document, incluading warranty) × 1

o For information about the warranty, users living in the USA and

Canada should see pages 50–51 and the back cover (war-

ranty document). Users living in Europe and other regions should

see page51.

Maintenance

Wipe dirt from the top cover and other panel surfaces using a

soft cloth that has been slightly dampened with a diluted neutral

cleanser.

Do not wipe with chemical cleaning cloths, thinner or other chemi-

cal agents. Doing so could damage the surface.

For your safety, disconnect the power cord from

the outlet before cleaning.

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

In the TEAC Downloads section, click the desired language to open

the Downloads website page for that language.

Included accessories

IMPORTANT SAFETY INSTRUCTIONS ...............................2

Included accessories ............................................... 5

Maintenance ......................................................5

Using the TEAC Global Site .........................................5

Before use .........................................................6

Note about pinpoint feet .......................................6

Front panel names and functions ..................................7

Rear panel names and functions ...................................8

Connecting speakers ..............................................9

Notes about speaker cables ....................................9

How to connect speakers .......................................9

Connections ......................................................10

Using STEREO output mode ...................................10

Using BI-AMP output mode ...................................11

Using BTL output mode .......................................12

Basic operation ...................................................13

Turning the power on .........................................13

Turning the power off .........................................13

Dimmer .......................................................14

Changing level meter operation ...............................14

Automatic power saving function .............................15

Restoring default settings .....................................15

Troubleshooting ..................................................16

Specifications .....................................................17

Amplifier ......................................................17

General .......................................................17

Included accessories ..........................................17

Thank you for choosing TEAC.

Read this manual carefully to get the best performance from this

unit.

After reading it, keep it in a safe place for future reference.

Placement precautions

o Place the unit in a stable location near the audio system that you

will use with it.

o Do not install this unit in a location that could become hot.

This includes places that are exposed to direct sunlight or near

a radiator, heater, stove or other heating equipment. Moreover,

do not place it on top of an amplifier or other equipment that

generates heat. Doing so could cause discoloration, deformation

or malfunction.

Also avoid locations that are subject to vibrations or exposed to

excessive dust, cold or moisture.

o When installing this unit, leave a little space (at least 3cm or 1")

between it and walls and other devices in order to allow good

heat dissipation.

If you put it in a rack, for example, leave at least 5cm (2") open

above it and at least 10cm (4") open behind it. Failure to provide

these gaps could cause heat to build up inside and result in fire.

o You may stack this unit with a PD-501HR, NT-505 or other

501/503/505 series units. However, if heat should cause the pro-

tection circuit to be activated and sound output stops suddenly,

place this unit on top and with sufficient distance between it and

walls and other devices in order to improve heat dissipation.

o Do not place CDs, CD-Rs, cassette tapes, other audio equipment

or other items that are susceptible to heat on top of the unit.

Doing so could damage these items.

o Do not put cloth on top of the unit or place the unit on top of

bedding or thick carpets. Doing so could cause the unit to over-

heat and damage it.

o Do not move the unit during use.

o The voltage supplied to the unit should match the voltage

printed on the bottom of the unit. If you are in any doubt regard-

ing this matter, consult an electrician.

o Do not open the body of the unit as this might result in damage

to the circuitry or cause electric shock. If a foreign object should

get into the unit, contact your dealer.

o When removing the power plug from the wall outlet, always pull

directly on the plug; never yank on the cord.

Before use

Note about pinpoint feet

High-precision metal pinpoint feet are attached firmly to the bot-

tom plate of this unit.

The stands for these feet are loose, but when the unit is placed in

position, it is supported by these pinpoint feet, which will effectively

disperse vibrations.

Chassis Pinpoint foot (metal)

Foot-stand (metal)

Screws that attach

foot-stand

o The included rubber pads are intended to protect the surface

where the unit is placed. Apply them to the bottoms of the

foot-stands.

Front panel names and functions

A STANDBY/ON switch

Use to put the unit into standby mode or turn it on.

B Level meters

These show the output levels.

C DIMMER/METER GAIN button

The brightness of the level meters changes each time you press

this button (page14).

Press and hold this button for three seconds to change level

meter operation (page14).

By using this button together with the STANDBY/ON switch,

you can change the automatic power saving setting and restore

various settings to their factory default values (page15).

B CA

Rear panel names and functions

ABCDE

A Analog audio input (INPUTS) connectors

Use these to input stereo analog audio. Connect these con-

nectors to the audio output connectors of a preamplifier or

another device such as a DAC that has a preamplifier function.

o This unit’s XLR connectors are 2: HOT.

Use commercially-available audio cables for connections.

RCA: RCA cables

XLR: XLR cables

Using with STEREO output mode

Connect this unit’s R input connector to the R output connec-

tor of the audio output device, and this unit’s L input connector

to the L output connector of the other device (page10).

Using with BI-AMP or BTL output mode

Connect this unit’s L connector to the L or R connector of the

audio output device. The R connector of this device is not used

(pages 11 and 12).

B INPUT SELECTOR switch

Use this to switch between input sources.

Do not switch this when the unit is on.

Failure to do so could result in sudden loud noises

that could damage speakers and harm your

hearing.

C OUTPUT MODE switch

This sets the output mode.

STEREO: stereo power amplifier (page10)

BI-AMP: mono bi-amplifier (page11)

BTL: mono power amplifier (page12)

Always disconnect speakers before changing

the output mode. Reconnect the speakers after

changing the mode.

D SPEAKERS terminals

This unit supports speakers that have a nominal impedance of

4Ω – 16Ω when the output mode is STEREO or BI-AMP and

8Ω – 16Ω when BTL.

Use commercially-available speaker cables to connect

the speakers.

E Power inlet (~IN)

Connect the supplied power cord here.

After all other connections are complete, connect the power

cord’s plug to a wall outlet.

Do not use any power cord other than the one

included with this unit. Use of other power cords

could result in fire or electric shock.

Unplug the cord from the outlet when not using

the unit for a long time.

F Maintenance port

This is used for maintenance. Do not connect anything to this

port unless instructed to do so by our service department.

Notes about speaker cables

o Use commercially-available speaker cables to connect the

speakers.

o Use the shortest speaker cables possible. The longer the cable,

the greater the resistance value and the more that damping

performance is reduced. Moreover, length also increases induc-

tance and capacitance, degrading the sound quality of high

frequencies.

o Use left and right speaker cables that have the same length.

Precautions when connecting speakers

o Connect the power plugs after all connections have been made.

o Carefully read the manuals of the devices that you are connect-

ing and follow their instructions when making connections.

o When the left and right grounds are shared in a sub woofer

with a built-in amplifier, for example, use might not be possible

depending on connection conditions.

ATTENTION

o This unit supports speakers that have a nominal impedance of

4Ω–16Ω when the output mode is STEREO or BI-AMP and

8Ω–16Ω when BTL. If speakers with lower impedance ratings

are used, the protection circuit could operate, causing sound

output to stop. In some cases, their use could even cause dam-

age to this unit or the speakers.

o This unit’s red terminal is positive (¥) and its black terminal

is negative (^). Generally, the ¥ wire of the speaker cable is

marked to distinguish it from the ^ wire of the cable. Connect

the marked wire to the red ¥ terminal and the unmarked wire

to the black ^ terminal.

o If the exposed end of a core wire in a speaker cable contacts

another cable or terminal, a short could occur.

o Never allow speaker cables to cause a short.

o To prevent hum and noise, avoid bundling the cables together

with the AC power cord or other cables.

Connecting speakers

How to connect speakers

1 Remove about one centimeter (1/2") of insu-

lation from the end of the speaker cable and

twist the core wires well.

2 Turn the terminal cap counterclockwise to

loosen it.

3 Insert the wire into the hole in the terminal

post and turn the terminal cap clockwise to

securely connect it.

o Connect it so that none of the wire insulation is touching

the terminal.

4 Conrm that the cable is fastened securely by

gently pulling the cable.

Connecting with banana plugs

You can also make connections using commercially-available

banana plugs. First, connect the banana plugs to the speaker cables

and then connect the plugs to the terminals.

o Keep the caps tightened when in use.

o Carefully read the instructions for the banana plugs that you are

using.

ATTENTION

Notice about the European model

In accordance with European safety regulations, connecting

banana plugs to speaker terminals is not allowed on European

models.

The holes into which banana plugs could be inserted have been

covered with black caps. Connect speakers using bare wires or

spade lugs.

If a black cap should become separated from its terminal, return

it to its original position.

Using STEREO output mode

Set the OUTPUT MODE switch to STEREO.

Connection example

Set the OUTPUT MODE

switch to STEREO.

Preamplifier or other device with

a preamplifier function

(such as a DAC)

XLR cables

RCA cables

Included power cord

Wall outlet

Connect a set of

cables of one type

or the other.

Speakers

Select the connectors

being used.

R L

Audio output

(PRE OUT, etc.)

R L

XLR pin assignment

1. COMMON

2. HOT (+)

3. COLD (−)

CAUTION

This unit does not have a volume adjustment function. Connect

this unit to a preamplifier or another device such as a DAC that has

a preamplifier function, and use that device to adjust the volume. If

you connect this unit to a device that cannot be used to adjust the

output volume, you will not be able to adjust the volume during

playback. Sound might be output from the speakers at a very loud

volume, which could harm hearing or damage equipment.

IMPORTANT NOTICE

When connecting this unit to a UD-505, NT-505, UD-503 or NT-503,

set the LINE OUT LEVEL to VARIABLE.

Connections

The use of this unit’s two built-in amplifier channels depends on the

OUTPUT MODE switch setting.

Connection examples for each mode are provided below.

Complete all other connections before setting the STANDBY/ON switch to ON.

o Carefully read the manuals of the devices that you are connecting and follow their instructions when making connections.

o Do not bundle connecting cables with power cords. Doing so could cause noise.

o Connect all plugs completely.

Using BI-AMP output mode

This unit can be used as a mono bi-amplifier.

Set the OUTPUT MODE switches on the units for the L and R chan-

nels to BI-AMP.

In BI-AMP mode, use two of these units for stereo playback.

What is bi-amp connection?

This method operates amplifiers independently for low-frequency

and high-frequency speaker units.

NOTE

o Sound input through the analog audio INPUTS L connector will

be output from both the L and R SPEAKERS connectors.

o Sound input through the analog audio INPUTS R connector will

not be output from the SPEAKERS connectors.

ATTENTION

o Bi-amplification is not possible with speakers that do not have

both low and high frequency connectors.

o When using bi-amp connections, remove speaker terminal links

and disconnect the connections between speaker ¥ connectors

and between ^ connectors.

Connection example

Set the OUTPUT MODE

switch to BI-AMP.

Set the OUTPUT MODE

switch to BI-AMP.

o Set the INPUT SELECTOR and OUTPUT MODE switches for

the R channel the same as for the L channel.

XLR cable

RCA cable

Wall outlet

Included power cord

Connect a set of

cables of one type

or the other.

Speaker

Select the connectors

being used.

R L

Audio output

(PRE OUT, etc.)

Speaker

AP-505 for R channel AP-505 for L channel

Wall outlet

Included power cord

Connect a set of

cables of one type

or the other.

RCA cable

XLR pin assignment

1. COMMON

2. HOT (+)

3. COLD (−)

Preamplifier or other device with

a preamplifier function

(such as a DAC)

Select the connectors

being used.

Using BTL output mode

This unit can be used as a mono BTL amplifier.

Set the OUTPUT MODE switches on the units for the L and R channels

to BTL.

In BTL mode, use two of these units for stereo playback.

What is BTL connection?

Two amplifier channels are used to drive the speaker for one chan-

nel. This is effective to realize high output for speakers with high

impedance.

NOTE

o Sound input through the analog audio INPUTS L connector will

be output from both the L and R SPEAKERS connectors.

o In BTL mode, sound input through the analog audio INPUTS R

connector will not be output from the SPEAKERS connectors.

ATTENTION

o Do not connect anything to the SPEAKERS ^ output connectors.

Connections (continued)

Connection example

R L

Set the OUTPUT MODE

switch to BTL.

Set the OUTPUT MODE

switch to BTL.

o Set the INPUT SELECTOR and OUTPUT MODE switches for

the R channel the same as for the L channel.

XLR cable

RCA cable

Wall outlet

Included power cord

Connect a set of

cables of one type

or the other.

Speaker

Select the connectors

being used.

R L

Audio output

(PRE OUT, etc.)

Speaker

AP-505 for R channel AP-505 for L channel

Wall outlet

Connect a set of

cables of one type

or the other.

RCA cable

XLR pin assignment

1. COMMON

2. HOT (+)

3. COLD (−)

Preamplifier or other device with

a preamplifier function

(such as a DAC)

Select the connectors

being used.

In order to protect the speakers, turn the power for systems that this

unit is connected to on and off in the following order.

NOTE

This explanation assumes that a preamplifier is connected to this

unit.

When connecting a UD-505, NT-505, UD-503 or NT-503

IMPORTANT NOTICE

Set the LINE OUT LEVEL to VARIABLE on the UD-505, NT-505, UD-503

or NT-503 in advance.

NOTE

o The UD-505, NT-505, UD-503 and NT-503 are equivalent to

preamplifiers.

o When using a UD-505, NT-505, UD-503 or NT-503 as a USB DAC

or using an NT-505 or NT-503 as a network player, it functions as

a preamplifier and a source device.

Connection example

Source device

CD player or other audio out-

put device

Preamplifier

Preamplifier or other device

with a preamplifier function

(such as a DAC)

AP-505

Turning the power on

1 Minimize the volume of the preamplier.

If using a device that cannot have its volume adjusted when it

is off, minimize the volume after turning it on.

2 Turn the source device on.

3 Turn the preamplier on.

Basic operation

4 Turn this unit on.

The level meters will blink and the mute function will turn on.

When the amplifier operation stabilizes, they will light and the

mute function will turn off.

5 Start playback on the source device, and adjust

the volume on the preamplier.

Adjust the preamplifier volume after the level meters on this

unit stop blinking and stay lit.

Turning the power off

1 If a connected device is playing back, stop

playback.

2 Minimize the volume of the preamplier.

3 Put the unit into standby mode.

4 Turn the preamplier o.

5 Turn the source device o.

Dimmer

You can change the brightness of the level meters.

Press the DIMMER/METER GAIN button to cycle through the bright-

ness settings in the following order.

Bright meters

Medium meters

Dim meters

Unlit meters

Changing level meter operation

Press and hold the DIMMER/METER GAIN button for three seconds

to cycle through the following operation modes.

Press for

3seconds

Normal

+20dB

Off

o When level meter operation is +20dB, needle movement will be

greater than usual.

Basic operation (continued)

Automatic power saving function

This unit has an automatic power saving function.

If the automatic power saving function is set to on, the unit will

automatically enter standby mode if there is no audio input for

about 30 minutes.

Turning automatic power saving on and off

1 While pressing the DIMMER/METER GAIN

button, set the STANDBY/ON switch to ON.

2 Immediately after setting the STANDBY/ON

switch to ON, release the DIMMER/METER GAIN

button.

Release immediately after setting

the STANDBY/ON switch to ON.

Releasing the DIMMER/METER GAIN button will switch the

automatic power saving function between on and off and the

level meters will blink.

You can check the automatic power saving setting by the blink-

ing of the level meters at this time.

Automatic power saving function on

Meters blink every 3seconds.

Automatic power saving function off

After blinking twice at 0.4-second intervals, meters continue to

alternately become lit and unlit at 3-second intervals.

Restoring default settings

1 While pressing the DIMMER/METER GAIN

button, set the STANDBY/ON switch to ON.

2 When the level meters blink, release the

DIMMER/METER GAIN button.

Keep pressing until the level

meters blink.

The factory default settings will be restored, and after the level

meters blink twice at 0.4-second intervals, the unit will enter

standby.

If you experience a problem with the unit, please take a moment

to review the following information before requesting service. If it

still does not operate correctly, contact the retailer where you pur-

chased the unit.

The unit does not turn on.

e Check that the power cord is completely plugged into the

power outlet. If the outlet is switched, confirm that the switch

is in the ON position.

e Connect a different electrical device to the outlet to confirm

that it is supplying power.

Noise occurs.

e Place the unit as far away as possible from TVs, microwave

ovens and other devices that have strong magnetism.

There is a humming noise.

e If a connecting cable is near a power cord, fluorescent light or

similar cause of interference, increase the distance between

them as much as possible.

No sound is output.

e Use the preamplifier volume knob to adjust the volume

(page13).

e Use the preamplifier input knob to select the source that you

want to hear (page13).

e Reconfirm the connections with other equipment.

e Check the INPUT SELECTOR switch setting on the back of the

unit.

The level meter lights are blinking and no sound is

output.

e The ¥ and ^ speaker cables might have shorted. Set the

STANDBY/ON switch to STANDBY, and check the speaker

connections.

Troubleshooting

Sound output stops suddenly and the level meter

lights are blinking.

e The protection circuit might have activated due to high tem-

perature, excessive load or another cause. Set the STANDBY/

ON switch to STANDBY, check the power and speaker connec-

tions, and wait several minutes before setting it to ON again.

If this unit is becoming hot, increase the amount of space

between it and walls and other devices to increase the dis-

sipation of heat.

Automatic power saving caused the unit to enter

standby.

e Set the STANDBY/ON switch to STANDBY once and then set it

to ON again.

Specifications

General

Power supply

Model for Europe ........................ AC 220–240V, 50/60Hz

Model for USA/Canada .......................... AC 120V, 60Hz

Power consumption

Models for Europe and USA/Canada ........................ 58W

External dimensions (W × H × D, including protrusions)

290 × 84.5 × 271mm (11 1/2" × 3 3/8" × 10 3/4")

Weight ............................................. 4.4kg (9 3/4lb)

Operating temperature range ....................... +5°C to +35°C

Operating humidity range ............. 5% – 85% (no condensation)

Storage temperature range ......................... −20°C to +55°C

Included accessories

Power cord × 1

Rubber pads × 3

Owner’s manual (this document, including warranty) × 1

o For information about the warranty, users living in the USA and

Canada should see pages50–51 and the back cover (warranty

document). Users living in Europe and other regions should see

page51.

o Design and specifications are subject to change without notice.

o Weight and dimensions are approximate.

o Illustrations in this manual might differ slightly from production

models.

Amplifier

Maximum effective output

STEREO or BI-AMP operation ...................... 170W + 170W

(4Ω, 1kHz, JEITA)

95W + 95W

(8Ω, 1kHz, JEITA)

BTL operation .............................................350W

(8Ω, 1kHz, JEITA)

Rated output

STEREO or BI-AMP operation ...................... 125W + 125W

(4Ω, THD 0.8%, 1kHz)

70W + 70W

(8Ω, THD 0.8%, 1kHz)

BTL operation .............................................230W

(8Ω, THD 0.8%, 1kHz)

Allowable speaker impedance

STEREO or BI-AMP operation .............................. 4–16Ω

BTL operation ............................................ 8–16Ω

Total harmonic distortion .................................. 0.0015%

(8Ω, 1kHz, 12.5W, JEITA)

S/N ratio (input short). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113dB

(8Ω, 1kHz, IHF-A)

Frequency response .................. 10Hz – 50kHz (+0dB, −5dB)

(8Ω, 1kHz, 1W, JEITA)

Input sensitivity

RCA connectors ........................................... 0.66V

(with 8Ω output, THD 1%)

XLR connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3V

(with 8Ω output, THD 1%)

Input impedance

RCA connectors .................................. 10kΩ or more

XLR connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10kΩ or more

INSTRUCTIONS DE SÉCURITÉ IMPORTANTES

ATTENTION : POUR RÉDUIRE LE RISQUE

D’ÉLECTROCUTION, NE RETIREZ PAS LE CAPOT (OU

L’ARRIÈRE). AUCUNE PIÈCE INTERNE N’EST RÉPARABLE

PAR L’UTILISATEUR. CONFIEZ TOUTE RÉPARATION À

UN SERVICE APRÈS-VENTE QUALIFIÉ.

Le symbole d’éclair à tête de flèche dans un triangle

équilatéral sert à prévenir l’utilisateur de la présence

dans l’enceinte du produit d’une «tension dangereuse»

non isolée d’une grandeur suffisante pour constituer un

risque d’électrocution pour les personnes.

Le point d’exclamation dans un triangle équilatéral

sert à prévenir l’utilisateur de la présence d’instructions

importantes de fonctionnement et de maintenance

(entretien) dans les documents accompagnant l’appareil.

AVERTISSEMENT: POUR PRÉVENIR LES RISQUES

D’INCENDIE ET D’ÉLECTROCUTION, N’EXPOSEZ

PAS CET APPAREIL À LA PLUIE NI À L’HUMIDITÉ.

ATTENTION

o NE RETIREZ PAS LES CAPOTS EXTERNES OU BOÎTIERS POUR

EXPOSER L’ÉLECTRONIQUE. AUCUNE PIÈCE INTERNE N’EST

RÉPARABLE PAR L’UTILISATEUR.

o SI VOUS RENCONTREZ DES PROBLÈMES AVEC CE PRODUIT,

CONTACTEZ LE MAGASIN OÙ VOUS AVEZ ACHETÉ L’UNITÉ.

N’UTILISEZ PAS LE PRODUIT TANT QU’IL N’A PAS ÉTÉ RÉPARÉ.

o L’UTILISATION DE COMMANDES, DE RÉGLAGES OU LE SUIVI

DE PROCÉDURES AUTRES QUE CE QUI EST DÉCRIT DANS CE

DOCUMENT PEUT PROVOQUER UNE EXPOSITION À UN

RAYONNEMENT DANGEREUX.

1) Lisez ces instructions.

2) Conservez ces instructions.

3) Tenez compte de tous les avertissements.

4) Suivez toutes les instructions.

5) N’utilisez pas cet appareil avec de l’eau à proximité.

6) Ne nettoyez l’appareil qu’avec un chiffon sec.

7) Ne bloquez aucune ouverture de ventilation. Installez-le confor-

mément aux instructions du fabricant.

8) N’installez pas l’appareil près de sources de chaleur telles que

des radiateurs, bouches de chauffage, poêles ou autres appareils

(y compris des amplificateurs) dégageant de la chaleur.

9) Ne neutralisez pas la fonction de sécurité de la fiche polarisée

ou de terre. Une fiche polarisée a deux broches, l’une plus large

que l’autre. Une fiche de terre a deux broches identiques et une

troisième broche pour la mise à la terre. La broche plus large ou

la troisième broche servent à votre sécurité. Si la fiche fournie

n’entre pas dans votre prise, consultez un électricien pour le

remplacement de la prise obsolète.

10) Évitez de marcher sur le cordon d’alimentation et de le pincer,

en particulier au niveau des fiches, des prises secteur, et du

point de sortie de l’appareil.

11) N’utilisez que des fixations/accessoires spécifiés par le fabricant.

12) Utilisez-le uniquement avec des chariots,

socles, trépieds, supports ou tables spécifiés

par le fabricant ou vendus avec l’appareil.

Si un chariot est utilisé, faites attention à ne

pas être blessé par un renversement lors

du déplacement de l’ensemble chariot/

appareil.

13) Débranchez cet appareil en cas d’orage ou de non utilisation

prolongée.

14) Confiez toute réparation à des techniciens de maintenance quali-

fiés. Une réparation est nécessaire si l’appareil a été endommagé

d’une quelconque façon, par exemple si le cordon ou la fiche

d’alimentation est endommagé, si du liquide a été renversé sur

l’appareil ou si des objets sont tombés dedans, si l’appareil a été

exposé à la pluie ou à l’humidité, s’il ne fonctionne pas normale-

ment, ou s’il est tombé.

o L’appareil tire un courant nominal de veille de la prise secteur

quand son interrupteur POWER ou STANDBY/ON n’est pas en

position ON.

o La fiche secteur est utilisée comme dispositif de déconnexion et

doit donc toujours rester disponible.

o Des précautions doivent être prises en cas d’utilisation d’écouteurs

ou d’un casque avec le produit car une pression sonore excessive

(volume trop fort) dans les écouteurs ou dans le casque peut cau-

ser une perte auditive.

ATTENTION

o N’exposez pas cet appareil aux gouttes ni aux éclaboussures.

o Ne placez pas d’objet rempli de liquide sur l’appareil, comme

par exemple un vase.

o N’installez pas cet appareil dans un espace confiné comme

une bibliothèque ou un meuble similaire.

o L’appareil doit être placé suffisamment près de la prise de

courant pour que vous puissiez à tout moment attraper facile-

ment la fiche du cordon d’alimentation.

o Si le produit utilise des piles/batteries (y compris un pack de

batteries ou des piles installées), elles ne doivent pas être

exposées au soleil, au feu ou à une chaleur excessive.

o PRÉCAUTION pour les produits qui utilisent des batteries rem-

plaçables au lithium: remplacer une batterie par un modèle

incorrect entraîne un risque d’explosion. Remplacez-les uni-

quement par un type identique ou équivalent.

AVERTISSEMENT

Les produits ayant une construction de Classe ! sont équipés

d’un cordon d’alimentation avec une fiche de terre. Le cordon

d’un tel produit doit être branché dans une prise secteur avec

terre de sécurité.

AUX USA/CANADA, UTILISEZ UNIQUEMENT UNE TENSION

D’ALIMENTATION DE 120V.

La plaque signalétique se trouve sous l’unité comme représenté

ci-dessous.

Façade

Plaque signalétique

INSTRUCTIONS DE SÉCURITÉ IMPORTANTES (suite)

Modèle pour le Canada

Déclaration de conformité d’Industrie Canada :

CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA

NORME NMB-003 DU CANADA

Modèle pour l’Europe

Ce produit est conforme aux directives euro-

péennes et aux autres réglementations de la

Commission européenne.

Pour les consommateurs européens

Mise au rebut des équipements électriques et électro-

niques et des piles et/ou accumulateurs

a) Tout équipement électrique/électronique et pile/accumula-

teur hors d’usage doit être traité séparément de la collecte

municipale d’ordures ménagères dans des points de collecte

désignés par le gouvernement ou les autorités locales.

b) En vous débarrassant correctement des équipements élec-

triques/électroniques et piles/accumulateurs hors d’usage, vous

contribuerez à la sauvegarde de précieuses ressources et à la

prévention de potentiels effets négatifs sur la santé humaine et

l’environnement.

c) Le traitement incorrect des équipements électriques/électro-

niques et piles/accumulateurs hors d’usage peut avoir des effets

graves sur l’environnement et la santé humaine en raison de la

présence de substances dangereuses dans les équipements.

d) Le symbole de déchets d’équipements électriques et

électroniques (DEEE), qui représente une poubelle à rou-

lettes barrée d’une croix, indique que les équipements

électriques/électroniques et piles/accumulateurs

doivent être collectés et traités séparément des déchets

ménagers.

Si une pile ou un accumulateur contient plus que les

valeurs de plomb (Pb), mercure (Hg) et/ou cadmium

(Cd) spécifiées dans la directive sur les piles et accumu-

lateurs (2006/66/CE, 2013/56/UE), alors les symboles

chimiques de ces éléments seront indiqués sous le

symbole DEEE.

e) Des systèmes de retour et de collecte sont disponibles pour

l’utilisateur final. Pour des informations plus détaillées sur la

mise au rebut des vieux équipements électriques/électro-

niques et piles/accumulateurs hors d’usage, veuillez contacter

votre mairie, le service d’ordures ménagères ou le magasin dans

lequel vous avez acquis l’équipement.

, Hg,

Les noms de société et de produit cités dans ce document sont des marques commerciales ou déposées de leurs détenteurs respectifs.

La page charge ...

TEAC AP-505 Le manuel du propriétaire

Marque: TEAC

Modèle: AP-505

Catégorie: Équipement musical supplémentaire

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: TEAC AP-505 Owner's manual
español: TEAC AP-505 El manual del propietario

TEAC AP-505 Le manuel du propriétaire

TEAC AP-505 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents