Esoteric F-05 Le manuel du propriétaire

F-05

D01286021A

OWNER’S MANUAL .................... 3

MODE D’EMPLOI ...................... 29

MANUAL DEL USUARIO ........... 55

Integrated Amplifier

3

English

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR

A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS

BEEN REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

Model for USA

This equipment has been tested and found to comply with the lim-

its for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular instal-

lation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Model for Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

This product complies with the European

Directives request, and the other Commission

Regulations.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to oper-

ate the equipment.

China RoHS

o The information in the following table is only applicable to products for sale in the People’s Republic of China.

o The products sold in the European area are manufactured in accordance with the European RoHS Directive.

*%7

)

*%7

4

IMPORTANT SAFETY INSTRUCTIONS (continued)

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete

outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

WARNING

Products with Class ! construction are equipped with a power

supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective

grounding connection.

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a

book case or similar unit.

o The apparatus should be located close enough to the AC

outlet so that you can easily reach the power cord plug at any

time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine,

fire or excessive heat.

o CAUTION for products that use replaceable lithium batter-

ies: there is danger of explosion if a battery is replaced with

an incorrect type of battery. Replace only with the same or

equivalent type.

5

English

MEXCEL is a registered trademark of Mitsubishi Cable Industries, Ltd. in Japan and other countries.

ESOTERIC is a trademark of TEAC CORPORATION, registered in the U.S. and other countries.

Other company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners.

V

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to

fire, injury or the staining of nearby things. Please read and observe

the following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and nega-

tive (^) orientations.

o Use batteries of the same type. Never use different types of batter-

ies together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery

compartment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The bat-

teries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal

waste stream via collection facilities designated by the govern-

ment or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valu-

able resources and prevent any potential negative effects on

human health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or

cadmium (Cd) as defined in the Battery Directive

(2006/66/EC), then the chemical symbols for those

elements will be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

6

Contents

Thank you for purchasing this Esoteric product.

Read this manual carefully to get the best performance from this

product. After reading it, keep it in a safe place with the warranty card

for future reference.

IMPORTANT SAFETY INSTRUCTIONS ...............................3

Before use .........................................................6

Precautions for use ................................................7

Connections ....................................................... 8

Connecting speakers .............................................10

Notes about the protection circuits ...............................11

Connections for use as a preamp .................................12

Connections for use as a power amp ..............................12

Notes about the remote control ..................................13

Names and functions of parts (main unit) .........................14

Using headphones ...............................................15

Names and functions of parts (remote control) ....................16

Basic operation ...................................................17

Settings ..........................................................21

Settings Menu 1 ..................................................22

Settings Menu 2 ..................................................23

Settings Menu 3 ..................................................24

Restoring factory settings .........................................25

Troubleshooting ..................................................26

Specifications .....................................................27

Dimensional drawings ............................................28

Before use

What’s in the box

Check to be sure the box includes all the supplied accessories shown

below. Please contact the store where you purchased this unit if

any of these accessories are missing or have been damaged during

transportation.

Power cord × 1

Remote control (RC-1301) × 1

Batteries for remote control (AAA) × 2

Felt pads* × 4

Owner’s manual (this document) × 1

Warranty card × 1

* Apply the included felt pads to the bottoms of the feet to avoid

scratching the surface where the unit is placed.

7

English

Precautions for use

o Place the unit in a stable location near the audio system that you

will use with it.

o Do not install this unit in a location that could become hot. This

includes places that are exposed to direct sunlight or near a radia-

tor, heater, stove or other heating equipment. Moreover, do not

place it on top of another amplifier or equipment that generates

heat.

o Avoid locations that are subject to vibrations or exposed to exces-

sive dust, cold or moisture.

o In order to enable good heat dissipation, leave at least 20 cm (8")

between this unit and walls and other equipment when installing

it. If you put it in a rack, take precautions to prevent overheating

by leaving at least 20 cm (8") open above the top of the unit and

at least 10 cm (4") open behind it. Failure to provide these gaps

could cause heat to build up inside and result in fire.

o Do not install the unit face up or on its side.

o Do not place anything, not even CDs, CD-Rs, LP records or cassette

tapes, on top of the unit. Do not put cloth on top of the unit or

place the unit on top of bedding or thick carpet.

o Do not move the unit during use.

o Be careful to avoid injury when moving the unit due to its weight.

Have someone help you move it if necessary.

o The voltage supplied to the unit should match the voltage printed

on the rear panel. If you are in any doubt regarding this matter,

consult an electrician.

o Do not open the body of the unit as this might result in damage

to the circuitry or cause electric shock. If a foreign object should

get into the unit, contact your dealer.

o When removing the power plug from the wall outlet, always pull

directly on the plug; never yank on the cord.

Maintenance

Use a soft dry cloth to wipe the surface of the unit clean.

For stubborn smudges, use a damp cloth that has been thoroughly

wrung out to remove excess moisture.

V

For safety, disconnect the power plug from the out-

let before cleaning.

o Never spray liquid directly on this unit.

o Do not use chemically-treated wipes, thinner or similar substances

because they could damage the surface of the unit.

o Avoid allowing rubber or plastic materials to touch the unit for

long periods of time because they could damage the cabinet.

8

Connections

V

Precautions when making connections

o After completing all other connections, plug the power plug into a power outlet.

o Read the owner’s manuals of all devices that will be connected, and follow their instructions.

o Do not bundle connecting cables with power cords. Doing so could cause noise.

A

DC

B

FA

E

XLR pin assignment

1. COMMON

2. HOT (+)

3. COLD (−)

Included power cord

Record player

RCA audio cables

XLR audio cables

Audio outputs

(AUDIO OUT, etc.)

Audio outputs

(AUDIO OUT, etc.)

Super Audio CD player,

tuner, etc.

Super Audio CD player,

etc.

Audio input

(AUDIO IN, etc.)

CD recorder, etc.

Change the phase inversion set-

ting when connecting a device

with 3 HOT (+) (page 22).

c

wall outlet

9

English

A Analog input (INPUTS) connectors

Connect the analog output connectors of Super Audio CD play-

ers, DVD players, cassette decks, tuners and other equipment to

these connectors.

Connect the R connector of a pair on this unit to the right (R)

connector of an output device and the L connector of the same

pair on this unit to the left (L) connector of the output device.

Use commercially-available cables for connections.

For XLR connectors: Use a balanced XLR audio cable.

Insert a balanced XLR plug until the connector lever locks.

Press this lever when disconnecting.

For RCA connectors: Use an RCA audio cable.

Connect the white pin plugs to the white (L) connectors and

connect the red pin plugs to the red (R) connectors.

o The XLR input connectors can be switched to 3 HOT (+)

(page 22).

Connecting record players

This unit has a built-in phono equalizer. When connecting a

record player, use the PHONO connectors.

o Always connect the record player’s ground to the SIGNAL

GND grounding connector on this unit.

o Use the PHONO MM/MC button to set the cartridge type

being used (page 19).

B SIGNAL GND grounding connector

Using a commercially-available sheathed wire to connect this

to the grounding terminal of a Super Audio CD player, power

amplifier or other device might improve the audio quality.

o This is not an electrical safety ground.

C Preamp input (EXT. PRE IN) connectors

Connect an external preamp here to use this unit as a power

amp (page 12).

D Analog output (PRE OUT/REC OUT) connectors

These output 2 channels of analog audio.

Connect these to the analog input connectors on another device.

When connecting these to a CD recorder or other audio input

device, set the PRE OUT output (page 23) according to the use.

To use this unit as a preamp, see “Connections for use as a pre-

amp” on page 12.

Connect the R connector of a pair on this unit to the right (R)

connector of an input device and the L connector of the same

pair on this unit to the left (L) connector of the input device.

Use commercially-available cables for connections.

For XLR connectors: Use a balanced XLR audio cable.

Insert a balanced XLR plug into the connector until it locks.

For RCA connectors: Use an RCA audio cable.

Connect the white pin plugs to the white (L) connectors and

connect the red pin plugs to the red (R) connectors.

E Optional board slot

This slot is for installing optional boards that are sold separately.

F AC power inlet (~IN)

Connect the included power cord to this socket. After complet-

ing all other connections, plug the power plug into a power

outlet.

V

Use only a genuine Esoteric power cord. Use of

other power cords could result in fire or electric

shock.

At Esoteric, we use Esoteric MEXCEL stressfree cables for

reference.

For detailed information, access the following website.

http://www.esoteric.jp/products/esoteric/accessory/indexe.html

10

Connecting speakers

Notes about speaker cables

o Use commercially-available speaker cables to connect the speakers.

o Use the shortest speaker cables possible. The longer the cable, the

greater the resistance value and the more that damping perfor-

mance is reduced. Moreover, length also increases impedance and

capacitance, degrading the sound quality of high frequencies.

o Use left and right speaker cables that have the same length.

How to connect speaker cables

Use commercially-available speaker cables to connect the + terminal

of the unit to the + terminal of the speaker and the − terminal of the

unit to the − terminal of the speaker.

o Use speakers with at least 4Ω impedance.

o If you plan to output sound from two sets of speakers at the same

time, use speakers with at least 8Ω impedance.

o If the exposed tip of the core wire of a speaker cable contacts

another cord or terminal, a short could occur.

Never allow a speaker cable to short.

o Do not connect more than one amplifier to a speaker.

o Do not bundle speaker cables with power cords. Doing so could

cause noise.

V

The power plug should always be disconnected

when connecting speaker cables.

Right speaker Left speaker

11

English

When using bare wires

Loosen the cap and insert the core wire into the hole in the terminal.

Then, tighten the cap.

When using spade lugs

Loosen the cap and insert the lug between the cap and base of the

terminal. Then, tighten the cap.

o When using a spade lug to connect, use one with an inside diam-

eter of at least 8 mm (3/8").

When using banana plugs

With the cap tightened, insert the plug into the opening in the end

of the terminal.

o Carefully read the instructions for the banana plugs that you are

using.

Notice about the European model

In accordance with European safety regulations, connecting

banana plugs to speaker terminals is not allowed on European

models. The holes into which banana plugs could be inserted

have been covered with black caps. Connect speakers using bare

wires or spade lugs. If a black cap should become separated from

its terminal, return it to its original position.

This unit has a DC protection circuit, an overcurrent protection circuit

and an overheating protection circuit built-in.

When a protection circuit is operating, the ring around the POWER

button blinks and one of the following error messages blinks on the

display.

DCout ERR!

The DC protection circuit is active.

Turn the unit off once and wait several minutes before turning it

on again.

OverCURNT!

The overcurrent protection circuit is active.

A short might have occurred with the +/− speaker cables. In this

case, turn the unit off and check the speaker cable connections.

Over TEMP!

The overheating protection circuit is active.

The internal temperature has become high. Turn the unit off and

wait a while for the temperature to decrease. You can also change

the installation conditions to improve ventilation.

o If the overheating protection circuit continues to operate for

30 seconds, the unit will automatically turn itself off. After this,

the POWER button will be disabled for as long as the internal

temperature remains high.

If the indicator continues to blink even after likely causes have been

eliminated, contact the store where you purchased the unit.

Notes about the protection circuits

12

Connections for use as a preamp

Power amplifier

Connect using a set

of only one type.

RCA audio cables

XLR audio cables

AUDIO IN

Connections

Use commercially-available XLR or RCA cables to connect the analog

output (PRE OUT/REC OUT) connectors on this unit to the analog

input connectors on the power amp.

Settings

Using Settings Menu 3, set the operation mode to PREAMP (page

25).

V

Precautions when making connections

After completing all other connections, plug the power plug into a

power outlet.

Read the owner’s manuals of all devices that will be connected, and

follow their instructions.

Do not bundle connecting cables with power cords. Doing so could

cause noise.

Connections for use as a power amp

XLR audio cables

Preamplifier

AUDIO OUT

Connections

Use commercially-available XLR cables to connect the preamp input

(EXT. PRE IN) connectors on this unit to the audio output connectors

on the preamp.

Settings

Using Settings Menu 3, set the operation mode to PWRAMP (page

25).

V

Precautions when making connections

After completing all other connections, plug the power plug into a

power outlet.

Read the owner’s manuals of all devices that will be connected, and

follow their instructions.

Do not bundle connecting cables with power cords. Doing so could

cause noise.

13

English

Notes about the remote control

Precautions for use

When using the remote control, point it toward the remote control

signal receiver on the main unit from a distance of 7 m (23 ft) or less.

Do not place obstructions between the main unit and the remote

control.

Moreover, operation from an angle can make reception difficult, so

use the remote facing the front of the main unit as much as possible.

7 m/23 ft

Remote control signal receiver

o The remote control might not work if the remote control signal

receiver is exposed to direct sunlight or bright light.

o Beware that use of this remote control could cause the unin-

tentional operation of other devices that can be controlled by

infrared rays.

Installing batteries

Remove the cover from the back of the remote control and insert

two AAA batteries with their ¥/^ oriented as shown in the case.

Replace the cover.

When to replace batteries

If the distance required between the remote and the main unit

decreases or if the unit stops responding to the remote buttons,

replace both batteries with new ones.

Dispose of the used batteries according to the instructions on them

or requirements set by your local municipality.

CAUTION

V

Misuse of batteries could cause them to rupture

or leak, which might result in fire, injury or the

staining of nearby materials.

Please read and observe the precautions on

page 5 carefully.

14

Names and functions of parts (main unit)

A INPUT knob

Turn this knob to select the active input. Select the input that is

connected to the device you want to use.

o You can change the names that are shown on the display for

the connectors (page 22).

When the Settings Screen is open, use this to change setting

values.

When inputting a source name, use this to move the cursor.

B Remote control signal receiver

This receives signals from the remote control. When using the

remote control, point the end of it toward this receiver panel

(page 13).

C Display

Shows the current input source name, volume, setting items, etc.

D VOLUME knob

Use to adjust the volume.

Turn this knob clockwise to increase the volume and counter-

clockwise to decrease it.

o The VOLUME knob will not affect input sources set to through

output (page 24).

V

Sudden loud noises might cause hearing damage and

other trouble. Always minimize the volume before

starting playback, and adjust it to an appropriate level

after playback begins.

E POWER button

Press to turn the unit on and off.

When the unit is on, the ring around the button lights blue.

o When not using the unit, turn it off.

o To protect your speakers, follow the proper procedures when

you turn the unit on or off (pages 17 and 18).

A

B C

F G H I J K LE

D

15

English

F Tone controls

Use these to adjust the levels of different frequency ranges.

Turn toward + to increase the level, and turn toward − to decrease

it.

Set to the o mark for a flat response (no adjustment).

BASS

Adjust the level of low frequencies.

MIDDLE

Adjust the level of medium frequencies.

TREBLE

Adjust the level of high frequencies.

o These adjustments only effect the output when TONE BYPASS

is off.

o When TONE BYPASS is off, “TONE” appears at the top of the

display.

G TONE BYPASS button

Use this to turn tone bypass on and off.

Press at least three seconds to open the Settings Screen.

H PHONO MM/MC button

Set for the cartridge type (MM/MC) used by the player con-

nected to the PHONO connectors (page 19).

I SPEAKER SELECT button

This selects which speaker connectors to use.

When the Settings Screen is open, press this to close it.

J BALANCE knob

Adjust the left-right volume balance.

K MUTE button

Press this button to temporarily mute the sound.

o When muted, “MUTE” blinks on the screen.

L PHONES jack

Connect standard 6.3mm stereo plugs here.

o When a headphone plug is inserted, speaker sound output

will stop.

Connect a headphone plug (standard 6.3mm stereo) to the PHONES

jack, and adjust the volume to a suitable level.

V

When using headphones, be careful not to turn the

volume up too much.

Using headphones

16

Names and functions of parts (remote control)

o The buttons not explained here do not function with this unit.

o This remote control can also be used for other Esoteric products.

a Setting (STANDBY/ON) button

On the Settings Screen, use to confirm selection of some set-

tings and to input connector names.

o This button does not turn the unit on/off.

b INPUT (k/j) buttons

Press these buttons to switch between input sources. Select the

connector that is connected to the device you want to play.

When the Settings Screen is open, use this to change setting

values.

When inputting a source name, use this to move the cursor.

c SETUP button

Use with Settings Screen Menus 1 and 2 (page 21).

d DIMMER button

Use to adjust the brightness of the display and indicators (page

20).

e VOLUME buttons (+/−)

Use to adjust the volume. Press the + button to increase the vol-

ume and the − button to decrease it.

o The VOLUME buttons (+/−) will not affect input sources set to

through output (page 24).

f MUTE button

Press this button to temporarily mute the sound.

Press again to restore the volume setting (page 18).

o When muted, “MUTE” blinks on the screen.

If both the main unit and the remote control have buttons with

the same function, we only explain procedures using one of them

in this manual. However, the other can also be used in the same

manner.

a

c

e

f

d

b

17

English

Basic operation

4 Play the source, and then adjust the volume by turn-

ing the VOLUME knob.

V

Sudden loud noises might cause hearing damage

and other trouble. Always minimize the volume

before starting playback, and adjust it to an

appropriate level after playback begins.

Turning the unit on

1 Turn on the connected input source devices.

2 Press the POWER button to turn the unit on.

The ring around the button lights blue.

o When using this unit as a preamp, turn on the power ampli-

fier last.

3 Turn the INPUT knob to select an input source.

18

Turning the unit off

There might be noise from the speakers if the unit is turned off sud-

denly. When you turn the unit off, follow the steps below.

1 If a connected device is playing back, stop playback.

o When using this unit as a preamp, turn off the power ampli-

fier first.

2 Turn the unit’s VOLUME knob counterclockwise to

minimize the volume.

V

Always turn the volume to the minimum level

before you turn the unit on or off. Failure to do so

could cause sudden loud noises that might result

in harm to your hearing or damage to the speakers

when you turn the unit on.

3 Press the POWER button to turn the unit o.

4 Turn o the connected input source devices.

Muting the output

Press the MUTE button to temporarily mute the sound. Press again to

restore the volume setting.

o When muted, “MUTE” blinks on the screen.

o You can also restore the sound by turning the VOLUME knob or by

pressing the VOLUME buttons (+/−).

Basic operation (continued)

19

English

Tone controls

You can separately adjust the levels of low (BASS), medium (MIDDLE)

and high (TREBLE) frequencies.

The o at the center marks the unadjusted level.

o These adjustments have no effect when TONE BYPASS is on.

Before adjusting them, press the TONE BYPASS button so that

“TONE” appears at the top of the display.

Tone bypass

When TONE BYPASS is on, audio signals do not pass through the tone

circuit before amplification.

When TONE BYPASS is off, “TONE” appears at the top of the display.

Setting the cartridge type

Set the cartridge type being used by the record player connected to

the PHONO connectors.

Turn the INPUT knob to set the input source to PHONO before press-

ing the PHONO MM/MC button to change the setting.

20

Selecting speakers

Press the SPEAKER SELECT button to cycle through the following

speaker selections.

A

c

B

c

A+B

Adjusting the balance

Adjust the balance between the left and right output channels.

Dimmer

Each time you press the DIMMER button, the brightness of the dis-

play and indicators change as follows.

DIMMER3

c

DIMMER2

c

DIMMER1

c

Off

(normal brightness)

o Even when set to off, the display will light at normal brightness for

a few seconds when you press a button or turn a knob. If TONE

BYPASS is on, however, this will not light when the tone controls

are turned.

o In setting mode, the display lights at normal brightness.

Basic operation (continued)

La page charge ...

Esoteric F-05 Le manuel du propriétaire

Esoteric F-05 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents