14-EN
01GB05CDA9887.fm
ALPINE CDA-9887 68-08564Z20-A (EN)
Setting EQ mode
This setting gives you a choice of 5-band parametric, or 7-band graphic
equalizer.
1
Press and hold FUNC./SETUP for at least 2
seconds to setup the Selection mode.
2
Turn the Rotary encoder to select AUDIO mode,
and then press / /ENT.
Bluetooth GENERAL AUDIO DISPLAY
TUNER
*
Bluetooth
* Only when HD Radio/SAT Radio is connected.
3
Turn the Rotary encoder to select EQ Mode, and
then press / /ENT.
4
Turn the Rotary encoder to select the desired
equalizer characteristic, and then press / /ENT.
Parametric EQ Graphic EQ
(Initial setting)
PEQ: 5-band Parametric EQ (Initial setting)
GEQ: 7-band Graphic EQ
5
Press and hold FUNC./SETUP for at least 2
seconds to return to normal mode.
• Pressing /RTN during the procedure will return to the previous
mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is canceled.
• This function is inoperable when DEFEAT is set to ON (page 13).
• Press and hold /ESC for at least 2 seconds, the setting mode is
canceled.
Adjusting and Storing the Parametric
Equalizer Curve
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste. To adjust the Parametric Equalizer
Curve, set the EQ mode to Parametric EQ. For details, refer to “Setting
EQ mode” (page 14).
1
Press A.SEL to recall the DSP adjust mode.
Media Xpander Crossover T.Correction
Parametric EQ/Graphic EQ Media Xpander
2
Turn the Rotary encoder to select Parametric EQ
mode, and then press / /ENT.
3
Press BAND to select the band to be adjusted.
Band1 Band2 Band3 Band4 Band5 Band1
4
Press or to select frequency bands.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
Band-1: 20 Hz~80 Hz (63 Hz)
Band-2: 50 Hz~200 Hz (150 Hz)
Band-3: 125 Hz~3.2 kHz (400 Hz)
Band-4: 315 Hz~8 kHz (1 kHz)
Band-5: 800 Hz~20 kHz (2.5 kHz)
5
Turn the Rotary encoder to adjust the level.
Adjustable level: -6 to +6 dB
6
Press SOURCE/ to set the bandwidth (Q).
Adjustable bandwidth: 1, 1.5, 3
7
To adjust another band, repeat steps 3 to 6 and
adjust all bands.
8
When the setting has been completed, select any
one of the preset buttons (1 through 6), press
and hold the desired preset buttons for at least 2
seconds.
9
Turn the Rotary encoder to select PROTECT
YES/NO, and then press / /ENT to store the
adjusted contents.
PROTECT YES PROTECT NO
(Initial setting)
• If YES is selected, the adjusted contents are protected and stored into
the preset buttons. When you want to store the parameter into a
protected preset button, “REPLACE NO/YES” can be selected.
• If NO is selected, the preset is stored.
10
After setting, press and hold /ESC for at least 2
seconds to return to normal mode.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• This function is inoperable when DEFEAT is set to ON (page 13).
• While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
• The stored contents are not deleted even when resetting the unit or
disconnecting the battery.
• The stored contents can be recalled by performing operation in
“Recalling the Stored Equalizer Curve” (page 15).
• Pressing /RTN when Parametric EQ is adjusted will return to the
previous item.
• If MultEQ is turned on, the A.SEL button is ineffective. For details,
refer to “Turning MultEQ on/off ” (page 13).
• If no operation is performed for 60 seconds, the unit will return to the
normal mode.
Adjusting and Storing the Graphic
Equalizer Curve
You can modify the equalizer settings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ mode to Graphic EQ. For details, refer to “Setting EQ mode”
(page 14).
1
Press A.SEL to recall the DSP adjust mode.
Media Xpander Crossover T.Correction
Parametric EQ/Graphic EQ Media Xpander
2
Turn the Rotary encoder to select Graphic EQ
mode, and then press / /ENT.
3
Press BAND to select the band to be adjusted.
Band1 Band2 Band3 Band4 Band5
Band6 Band7 Band1
Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /
Band-7 (17.5 kHz)
68-08564Z20-A_F.book Page 14 Thursday, March 15, 2007 3:36 PM