Windsor Chariot 2 iScrub 20 Deluxe with ORB Technology Le manuel du propriétaire

Register

your product

www.kaercher.com/welcome

86398220-H 10/31/19

Chariot 2 iScrub 20

English 02

From Serial Number (Ref No. 1*)

* See Serial Number page in Spare

Parts List or call manufacturer.

2 86398220 Operators Manual - Chariot-2 iScrub 20

Machine Data Label

Overview

The Chariot Scrubber is a battery powered, stand-on, hard floor scrubber intended for commercial use. The

appliance applies a cleaning solution onto a hard floor, scrubs the floor with brush or pad, and then vacuums the

soiled water back into the recovery tank.

Warranty Registration

Thank you for purchasing a Kärcher North America product. Warranty registration is quick

and easy. Your registration will allow us to serve you better over the lifetime of the product.

To register your product go to :

http://warranty.karcherna.com

For customer assistance:

1-800-444-7654

MODELS:

CS20 1.006-125.0

CSC20 1.006-133.0

CSX20 1006-137.0

CSXC20 1.006-138.0

CS22SP 1.006-130.0

CSC22SP 1.006-134.0

CSXM20 1.006-170.0

CSXCM20 1.006-171.0

CSM22SP 1.006-172.0

CSCM22SP 1.006-173.0

CSXBCM20 1.006-181.0

CSXBC20 1.006-182.0

CSXBM20 1.006-183.0

CSXB20 1.006-184.0

3

Table of Contents

Machine Data Label . . . . . . . . . . . . . . . . . . . . . . . . . .2

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .3

How To Use This Manual . . . . . . . . . . . . . . . . . . . . .4

Safety

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . .5

HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . .7

SAFETY LABEL LOCATIONS . . . . . . . . . . . . . . . . .9

Operations

Technical Specifications . . . . . . . . . . . . . . . . . . . . .10

How This Machine Works . . . . . . . . . . . . . . . . . . . .12

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Drive Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Scrub Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Scrub Controls - Squeegee. . . . . . . . . . . . . . . . . . .20

Scrub Controls - Solution Flow Rate. . . . . . . . . . . .22

Pre-Run Machine Inspection. . . . . . . . . . . . . . . . . .23

Starting Machine . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Emergency Stop Procedure . . . . . . . . . . . . . . . . . .23

Filling Solution Tank . . . . . . . . . . . . . . . . . . . . . . . .23

Normal Scrubbing . . . . . . . . . . . . . . . . . . . . . . . . . .24

To Begin Scrubbing . . . . . . . . . . . . . . . . . . . . . . . .24

Double Scrub . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Finish Removal (on select orbital models) . . . . . . .26

Emptying and Cleaning Tanks . . . . . . . . . . . . . . . .27

Models with Chemical Metering System . . . . . . . . .28

Maintenance

Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . .30

Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Changing Batteries . . . . . . . . . . . . . . . . . . . . . . . . .36

Delta Q IC650 Charger Maintenance Instructions .37

Delta Q IC650 Charger Operating Instructions. . . .38

Charge Tracking Data. . . . . . . . . . . . . . . . . . . . . . .41

To Remove Squeegee Assembly . . . . . . . . . . . . . .42

Squeegee Blades-Cylindrical . . . . . . . . . . . . . . . . .43

Scrub Brush-Disk . . . . . . . . . . . . . . . . . . . . . . . . . .45

Scrub Brush-Orbital . . . . . . . . . . . . . . . . . . . . . . . .45

Finished Floors . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Replacing or Installing Scrub Brushes (Disk) . . . . .46

Replacing or Installing Scrub Pad (Orbital). . . . . . .46

Replacing or Installing Scrub Brushes (Cylindrical) 46

Removal or Installation of Debris Bin (Cylindrical) .47

To Replace Scrub Brush Motor - Disk . . . . . . . . . .48

To Replace Scrub Brush Motor - Orbital. . . . . . . . .48

Scrub Deck Actuator Removal / Replacement . . . .50

Circuit Protection. . . . . . . . . . . . . . . . . . . . . . . . . . .51

Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Tank Assembly Removal . . . . . . . . . . . . . . . . . . . .54

Drive Unit Removal . . . . . . . . . . . . . . . . . . . . . . . . .55

Vacuum & Float Shutoff . . . . . . . . . . . . . . . . . . . . .56

Vacuum Motor Carbon Brush Replacement . . . . . .57

Drive Motor-From Serial Number (4*) . . . . . . . . . . .58

Drive Motor Carbon Brush Replacement . . . . . . . .58

Drive Chain Tension . . . . . . . . . . . . . . . . . . . . . . . .58

Transporting Machine . . . . . . . . . . . . . . . . . . . . . . .58

Brake Override . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Inclines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Drive Motor-Prior to Serial Number(4*). . . . . . . . . .60

Drive Chain Tension . . . . . . . . . . . . . . . . . . . . . . . .60

Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Inclines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Machine Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . .62

Machine Tie-Downs (Deluxe) . . . . . . . . . . . . . . . . .63

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .64

Battery Discharge Indicator Troubleshooting . . . . .66

Suggested Spare Parts - Disk. . . . . . . . . . . . . . . . 67

Suggested Spare Parts - Orbital . . . . . . . . . . . . . . 68

Suggested Spare Parts - Cylindrical . . . . . . . . . . . 69

86398220 Operators Manual - Chariot-2 iScrub 20

4

How To Use This Manual

This manual contains the following sections:

• HOW TO USE THIS MANUAL

• SAFETY

•OPERATIONS

• MAINTENANCE

The HOW TO USE THIS MANUAL section will tell you

how to find important information for ordering correct

repair parts.

Parts may be ordered from authorized dealers. When

placing an order for parts, the machine model and

machine serial number are important. Refer to the

MACHINE DATA box which is filled out during the

installation of your machine. The MACHINE DATA box

is located on the inside of the front cover of this manual.

The model and serial number of your machine is

located on the back of the machine.

The SAFETY section contains important information

regarding hazardous or unsafe practices of the

machine. Levels of hazards are identified that could

result in product damage, personal injury, or severe

injury resulting in death.

The OPERATIONS section is to familiarize the operator

with the operation and function of the machine.

The MAINTENANCE section contains preventive main-

tenance to keep the machine and its components in

good working condition. They are listed in this general

order:

• Batteries

• Scrub Brush

• Squeegee

• Service Schedule

• Machine Troubleshooting

NOTE: The manual part number is located on the

lower right corner of the front cover.

Model:

Date of Purchase:

Serial Number:

Dealer:

Address:

Phone Number:

Sales Representative:

86398220 Operators Manual - Chariot-2 iScrub 20

5

Safety

IMPORTANT SAFETY INSTRUCTIONS

When using this machine, basic precaution

must always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.

To reduce the risk of fire, electric shock, or injury:

Use only indoors. Do not use outdoors or expose to rain.

Use only as described in this manual. Use only manufacturer's recommended components and attachments.

If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to

an authorized service center.

Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.

This machine is not suitable for picking up hazardous dust.

Do not operate this machine near flammable fluids, dust or vapors.

Maintenance and repairs must be done by qualified personnel.

If foam or liquid comes out of machine, switch off immediately.

Disconnect battery before cleaning or servicing.

Before the machine is discarded, the batteries must be removed and properly disposed of.

Make sure all warning and caution labels are legible and properly attached to the machine.

During operation, attention shall be paid to other persons, especially children.

Before use all covers and doors shall be put in the positions specified in the instructions.

When leaving unattended, secure against unintentional movement.

The machine shall only be operated by instructed and authorized persons.

When leaving unattended, switch off or lock the main power switch to prevent unauthorized use.

Only chemicals recommended by the manufacturer shall be used.

This appliance has been designed for use with the brushes specified by the manufacturer. The fitting of other

brushes may affect its safety.

Do not use on surfaces having a gradient of over 10% (6 degrees).

READ AND SAVE THESE INSTRUCTIONS

86398220 Operators Manual - Chariot-2 iScrub 20

6

Safety

MESURES DE SÉCURITÉ IMPORTANTES

Lors de l'utilisation d'un appareil à batteries, il est nécessaire de respecter

systématiquement des mesures de sécurité de base, comme suit :

PRENEZ NOTE DE TOUTES CES MESURES AVANT D'UTILISER CETTE MACHINE.

Pour réduire les risques d'incendie, de chocs électriques, ou de blessures :

N'utiliser cette machine qu'en intérieur. Ne jamais l'utiliser à l'extérieur ou dans la pluie.

Utiliser cet appareil conformément aux instructions du présent manuel uniquement. N'utiliser que les composants

et les accessoires conseillés par le fabricant.

Lorsque la machine ne fonctionnant pas correctement, a fait l'objet d'une chute ou d'une détérioration, a été laissée

à l'extérieur, est tombée dans l'eau, la retourner au centre de service agréé.

Ne pas opérer la machine lorsque les conduits de ventilation sont bloquées. Débarrasser les débris des conduits,

car ils peuvent réduire l'écoulement d'air.

Cette machine n'est pas adaptée au ramassage de poussières dangereuses

Ne pas l'utiliser près de liquides, de poussières ou de vapeurs inflammables.

L'entretien et les réparations de la machine doivent être effectuées par un personnel qualifié.

Si de la mousse ou du liquide sort de la machine, la mettre hors tension immédiatement.

Déconnecter les batteries avant de nettoyer la machine ou de la soumettre à un entretien.

Avant de se débarrasser de la machine, il est nécessaire de retirer les batteries et de les jeter correctement.

S'assurer que toutes les plaques d'avertissement ou de précaution sont lisibles et fixées correctement sur la

machine.

Durant la manoeuvre de la machine, prendre garde aux personnes environnantes et notamment aux enfants.

Avant l'utilisation de la machine, veiller à positionner tous les couvercles et portes comme indiqué dans les instruc-

tions.

Lorsque la machine est laissée sans surveillance, s'assurer qu'elle ne se déplace pas de manière accidentelle.

Cette machine ne doit être manoeuvrée que par un personnel expérimenté et qualifié.

Lorsque la machine est laissée sans surveillance, la mettre hors tension ou verrouiller l'interrupteur principal afin

d'empêcher un emploi non autorisé.

Seuls les produits chimiques recommandés par le fabricant doivent être utilisés.

Cette machine a été conçue pour être utilisée avec des brosses spécifiées par le fabricant.

L'utilisation d'autres brosses peut affecter sa sûreté.

N'employez pas sur des surfaces ayant un gradient de plus de 10% (6 degrés).

CONSERVER CES INSTRUCTIONS

86398220 Operators Manual - Chariot-2 iScrub 20

7

Safety

The following symbols are used throughout this guide as indicated in their descriptions:

HAZARD INTENSITY LEVEL

There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY.

The level of hazard intensity is determined by the following definitions:

WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.

FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.

Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating

condition. Following is information that signals some potentially dangerous conditions to the operator or the equip-

ment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the

machine. Please take the necessary steps to train the machine operating personnel.

FOR SAFETY:

DO NOT OPERATE MACHINE:

Unless Trained and Authorized.

Unless Operation Guide is Read and understood.

In Flammable or Explosive areas.

In areas with possible falling objects.

WHEN SERVICING MACHINE:

Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use

approved replacement parts.

Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep battery

compartment open during charging. Keep sparks and flames away from the batteries. Do not smoke

around batteries.

Disconnect batteries before working on machine. Only qualified personnel should work inside machine.

Always wear eye protection and protective clothing when working on or near batteries. Avoid skin contact

with the acid contained in the batteries.

Never allow metal to lie across battery tops.

86398220 Operators Manual - Chariot-2 iScrub 20

8

Safety

Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions :

DEGRÉS DE RISQUES EN CAS DE DANGER

Il existe trois degrés de risques identifiés par les termes signalétiques -AVERTISSEMENT et ATTENTION et POUR

VOTRE SÉCURITÉ. Le degré de risque est défini de la manière suivante:

AVERTISSEMENT - Dangers ou méthodes dangereuses qui POURRAIENT provoquer de graves blessures ou

entraîner la mort.

ATTENTION - Dangers ou méthodes dangereuses qui pourraient provoquer des blessures légères ou une détério-

ration du produit ou des biens immobiliers.

POUR VOTRE SÉCURITÉ: ce signe permet d'identifier les mesures de précaution à prendre pour assurer un bon

fonctionnement du matériel.

Rendre compte immédiatement d'une défaillance ou d'une détérioration de la machine. Ne pas utiliser la machine

si celle-ci ne fonctionne pas correctement. Lire soigneusement les informations ci-dessous signalant certains

dangers potentiels pour l'opérateur de la machine. L'opérateur doit être absolument au courant de ces dangers

potentiels. Localiser tous les dispositifs de sécurité sur la machine. Il est conseillé de prendre les mesures néces-

saires pour former le personnel opérateur.

POUR VOTRE SÉCURITÉ:

NE PAS MANOEUVRER LA MACHINE:

Lorsqu'on n'est pas expérimenté ou qualifié.

Lorsque le guide d'utilisation n'est pas été lu ou compris.

Dans des zones inflammables ou explosives.

Dans des zones où des objets peuvent tomber.

LORS DE L'ENTRETIEN DE LA MACHINE:

Éviter les parties amovibles. Ne pas porter de vêtements amples, tels que des vestes, des chemises ou des

vêtements avec manches lors de l'utilisation de la machine. Utiliser les pièces détachées homologuées.

Les batteries émettent le gaz d'hydrogène. L'explosion ou le feu peut résulter. Étincelles de subsistance et

flamme nue loin. Compartiment de batterie de subsistance ouvert en chargeant. Étincelles et flammes de

subsistance loin des batteries. Ne fumez pas autour des batteries.

Déconnecter les batteries avant de travailler sur la machine. La machine ne doit être confiée qu'à un

personnel qualifié. Porter systématiquement des lunettes et des vêtements de protection lors d'une inter-

vention sur les batteries ou aux alentours. Éviter tout contact de la peau avec l'acide contenu dans les

batteries.

Ne jamais placer d'objets métalliques sur le dessus des batteries.

86398220 Operators Manual - Chariot-2 iScrub 20

9

Safety

SAFETY LABEL LOCATIONS

These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible,

promptly replace them.

EMPLACEMENT DE L'ÉTIQUETTE DE SÉCURITÉ

REMARQUE : Ces dessins indiquent l'emplacement des étiquettes de sécurité sur la machine. Si, à tout moment,

les étiquettes deviennent illisibles, contactez votre représentant autorisé pour un remplacement rapide.

CAUTION

BATTERY

86252520

WARNING LABEL

86244300

CAUTION

CAUTION LABEL

86244310

CAUTION LABEL

86335010 (1X)

LABEL

WARNING

86385070

CAUTION LABEL

86335010

(ON BOARD CHARGER

MODELS ONLY)

CAUTION LABEL

86335010

(1X ON DISK DECK)

(2X ON ORBITAL DECK)

86398220 Operators Manual - Chariot-2 iScrub 20

10

Operations

Technical Specifications

ITEM DIMENSION/CAPACITY

Nominal Power-Disk 1080 W

Nominal Power-Orbital 936 W

Nominal Power-Cylindrical 1512 W

Rated Voltage 36 Volts DC

Rated Amperage -Disk 30 amps

Rated Amperage -Orbital 26 amps

Rated Amperage -Cylindrical 42 amps

Batteries 3 X12 Volt 130 AH @ 20 hr. rate

Battery Compartment Dimensions 20-1/2 in. x 13 in. x 10 in. tall (330mm x 521mm x 254mm)

Scrub Brush Motor - Disk Machine 1 x .28 HP (209 W)

Scrub Brush Motor - Orbital Machine 1 x .5 HP (373 W)

Scrub Brush Motor - Cylindrical Machine 1 x .8 HP (600 W)

Vacuum Motor .63 HP (470 W)

Maximum flow rate of vacuum motor 72 cfm (33.98 liters per second)

Maximum suction of vacuum motor 47.3 inches of water (11.7 kPa)

Propelling Motor .38 HP (280 W)

Mass (GVW) 827 lbs (375 kg)

Weight empty without batteries - Disk 209 lbs (96 kg)

Weight empty without batteries - Orbital 271 lbs (123 kg)

Weight empty without batteries - Cylindrical 255 lbs (116 kg)

Solution Control Gravity, 1/3 GPM average

Solution capacity 10 gal (38 L)

Recovery capacity 10 gal (38 L)

Scrub brush diameter - Disk 20 inch (508 mm)

Scrub brush length - Cylindrical 22 inch (559 mm)

Scrub brush pressure - Disk / Orbital 50 lbs (222N)

Scrub brush pressure - Cylindrical 46 lbs (21 kg)

Scrub brush speed - Disk 180 rpm

Scrub brush speed - Cylindrical 1500 rpm

Tires 8 in. (203mm) drive, 6 in. (156mm) rear, polyurethane

Maximum Speed 2.4 mph (3.7 kph)

Brake Electrical parking brake,sets automatically whenever operator stops.

Minimum aisle u-turn width 51in. (1295 mm)

Maximum rated climb and descent angle 10% (6 degrees)

Vibration, hands - Disk 1.6 m/s²

Vibration, feet - Disk 0.54 m/s²

Uncertainty - Disk 0.5 m/s²

Sound pressure level - Disk 68.0 dBA

Sound power level - Disk 81.1 dBA

Uncertainty - Disk 3.0 dBA

Vibration, hands - Cylindrical 1.5 m/s²

Vibration, feet - Cylindrical 0.9 m/s²

Uncertainty - Cylindrical 0.5 m/s²

Sound pressure level - Cylindrical 71.5 dBA

Sound pressure level - Cylindrical 84.7 dBA

Uncertainty - Cylindrical 3.0 dBA

86398220 Operators Manual - Chariot-2 iScrub 20

11

Operations

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure

that they do not play with the appliance.

Cet appareil n'est pas prévu à l'usage des personnes (enfants y compris) avec des possibilités physiques, sensori-

elles ou mentales réduites, ou le manque d'expérience et de connaissance, à moins qu'ils aient été donnés la

surveillance ou l'instruction au sujet de l'utilisation de l'appareil par une personne chargée de leur sûreté. Des

enfants devraient être dirigés pour s'assurer qu'ils ne jouent pas avec l'appareil.

ITEM MEASURE

Height 51.8 in (1316mm)

Length 44.0 in (1118mm)

Width without squeegee - Disk / Orbital 23.4 in (594mm)

Width without squeegee - Cylindrical 25.4 in (645mm)

Width of squeegee - Disk / Orbital 27.2 in (691mm)

Width of squeegee - Cylindrical 29.3 in (744mm)

Width of scrub path - Disk / Orbital 20 in (508mm)

Width of scrub path - Cylindrical 22 in (559mm)

WIDTH

LENGTH

HEIGHT

86398220 Operators Manual - Chariot-2 iScrub 20

12

Operations

How This Machine Works

The Chariot® is a battery powered, self-propelled, hard

floor scrubber intended for commercial use. The

appliance applies a cleaning solution onto a hard floor,

scrubs the floor with a brush, and then vacuums the

soiled water back into the recovery tank.

The machine's primary systems are the solution

system, scrub system, recovery system, and operator

control system.

The function of the solution system is to store cleaning

solution and deliver it to the scrub system. The solution

system consists of the solution tank, strainer, metering

valve and solenoid valve. The solution tank stores

cleaning solution (water and detergent) until it is

delivered to the scrub system. The strainer protects the

valves from debris. The solenoid valve automatically

prevents solution flow unless the scrub brush is turned

on and the machine is being propelled.

The function of the scrub system is to scrub the floor.

The disk scrub system consists of one rotary type disk

scrub brush, motor, scrub deck skirt and lift actuator.

The brush scrubs the floor as the motor drives the

brush. The brush drive hub allows the scrub brush to

follow irregularities and changes in the floor without

losing contact with the floor. The scrub deck skirt

controls the cleaning solution on the floor so that the

squeegee can pick it up.

The cylindrical scrub system consists of two cylindrical

brushes, motor, side squeegees, and lift actuator. The

two counter rotating brushes scrub the floor, driven by a

single motor. The brush deck “floats” with constant

brush pressure. The side squeegees keep the cleaning

solution within the brush deck width, allowing the main

squeegee to pick the solution up.

The function of the recovery system is to vacuum the

soiled water back into the recovery tank. The recovery

system consists of the squeegee, vacuum motor, float

ball, recovery tank. The squeegee wipes the dirty

solution off the floor as the machine moves forward.

The vacuum motor provides suction to draw the dirty

solution off the floor and into the recovery tank. The

float ball filter protects the vacuum fan from debris and

foam. The recovery tank stores the dirty solution.

The function of the operator control system is to control

the direction and speed of the machine. The directional

control system consists of the direction control drive

reset switch, throttle pedal, emergency stop/brake

switch, steering wheel, propel controller, and drive

wheel. The directional control drive reset switch signals

forward or reverse direction and makes sure the

operator is on the platform before machine will propel.

The controller interprets signals from the throttle pedal

to command the drive wheel to propel or slow the

machine. The steering wheel points the drive wheel in

the direction desired by the operator. The parking brake

automatically engages when the operator stop the

machine. The emergency stop/brake can be used to

hold the machine on slopes.

86398220 Operators Manual - Chariot-2 iScrub 20

13

Operations

Components

1. Drive Control

2. Scrub Controls

3. Control Console

4. Pedal Platform

5. Solution Tank

6. Recovery Tank

7. Recovery Sight Dome

8. Recovery Drain Hose

9. Scrub Deck Skirt

10. Solution Cover

11. Solution Drain Hose/Solution Level Indicator

12. Squeegee

86398220 Operators Manual - Chariot-2 iScrub 20

Cylindrical

Deluxe Disk & Cylindrical

12

10

9

10

12

1

2

3

4

5

6

7

8

9

11

14

Operations

Drive Controls

1

2

3

4

5

6

7

8

9

10

86398220 Operators Manual - Chariot-2 iScrub 20

15

Operations

1. Key Switch

2. Emergency Stop/Brake Switch

3. Directional Control / Drive Reset Switch

4. Throttle Pedal

5. Horn Button

6. Steering Wheel

7. Speed Control

8. Battery Discharge Indicator

9. Hour Meter

10. Operator Presence Switch

1. KEY SWITCH

Controls the power for machine functions.

To turn the machine power on, rotate key clock-

wise.

To turn the machine off, rotate key counterclock-

wise.

When the key is turned on the battery symbol will

flash once and stay on continuously.

2. EMERGENCY STOP/BRAKE SWITCH

This safety feature is designed to cut all power to

the machine at any time and apply parking brake.

To shut the machine power off, push the

Emergency Stop Switch, this will also engage the

parking brake and cause the machine to stop

immediately.

To reset the machine, rotate the switch clockwise.

3. DIRECTIONAL CONTROL / DRIVE RESET

SWITCH

This safety feature is designed to ensure safe

engagement of propel drive. Each time the

machine power is turned on, or each time an

operator steps on to the platform, the Drive Reset

Switch must be pushed before machine will propel.

The switch controls the direction of travel of the

vehicle. The lighted arrow on the switch indicates

direction of travel.

To travel forward, press the top of the switch.

To travel in reverse, press the bottom of the switch.

86398220 Operators Manual - Chariot-2 iScrub 20

16

Operations

4. THROTTLE PEDAL

Controls the speed of the vehicle within the speed control setting selected. Pressing the pedal causes the

machine to travel in the direction selected by the Directional Control Switch.

To increase speed, increase pressure on the pedal.

To decrease speed, decrease pressure on the pedal.

5. HORN BUTTON

The horn is activated by pressing the horn button.

6. STEERING WHEEL

The steering wheel turns the front wheel causing the machine to change direction.

7. SPEED CONTROL

Controls the maximum speed of the machine. There are two settings, slow and fast.

To change speed, rotate the dial to either slow or fast position. The slow position is to the left (counterclock-

wise), fast to the right (top position).

The throttle pedal will always regulate the speed between 0 and maximum.

86398220 Operators Manual - Chariot-2 iScrub 20

17

Operations

8. BATTERY DISCHARGE INDICATOR

Indicates the charge level of the batteries.

The indicator will be illuminated if the batteries have a sufficient charge. A slow, continuous flash indicates the

batteries require charging.

The Battery Lockout function will activate when the batteries are low.

Once active, the LED status indicator will begin to flash slowly and the controller will inhibit the scrub motor and

water solenoid. The vacuum and drive remain functional. The “vacuum only” selection (position ‘B’) can be

used to vacuum up any remaining water. Return the unit to the charging station and charge the batteries.

NOTE: Continuing usage may damage the batteries.

When the machine is left overnight with less than a full charge, the display may initially indicate a full charge. It

will also indicate a full charge if the batteries are disconnected, then reconnected. After a few minutes of

operation the indicator will give the correct charge level.

9. HOUR METER

Records the number of hours the machine has been in scrubbing operation. This information is useful in deter-

mining when to service the machine.

86398220 Operators Manual - Chariot-2 iScrub 20

18

Operations

Scrub Controls

1. FUNCTION MODE SWITCH

The first two positions are for transport only. See drive controls section.

Light cleaning

This mode is used for light cleaning. In this mode the machine will propel at fast speed. The

‘floating’ scrub deck and squeegee is in the down position. The water will flow. Water will auto-

matically shut off in neutral and restarts when scrubbing is resumed. The vacuum will draw the

water into the recovery tank.

Deep cleaning

This mode is used for deep cleaning. In this mode the machine will propel at a low speed. The

‘floating’ scrub deck and squeegee is in the down position. The water will flow. Water will auto-

matically shut off in neutral and restarts when scrubbing is resumed. The vacuum will draw the

water into the recovery tank.

1

LABEL WITH CHEMICAL METERING OPTION.

LABEL WITH FINISH REMOVAL MODE.

86398220 Operators Manual - Chariot-2 iScrub 20

19

Operations

Vacuum only mode

This mode is used for picking up solution only. The brush and water will both be up and off. In

this mode the machine will propel at fast speed. The squeegee is lowered and the vacuum will

come on.

Double Scrub cleaning (with chemical metering on equipped models)

This mode is used for putting down solution and scrubbing without picking it back up. The

squeegee is set manually by connecting the two double scrub support cables. In this mode the

machine will propel at a slow speed. The scrub deck will lower. The solution will flow. The brush

and water will shut off when the machine is in neutral. They will resume when propelling is

resumed.

Light cleaning with chemical metering

Chemical dilution rate to be set by chemical metering selection switch.

Deep cleaning with chemical metering

Chemical dilution rate to be set by chemical metering selection switch.

Finish removal (on select orbital models)

This mode is used for removing floor finish without the use of chemicals. In this mode the

machine will propel at a very slow speed. The 'floating' scrub deck and squeegee are in the

down position. The water will flow while propelling and will automatically shut off in neutral.

Water flow rate is controlled by the flow shut-off valve. The vacuum will draw water into the

recovery tank.

86398220 Operators Manual - Chariot-2 iScrub 20

20

Operations

Scrub Controls - Squeegee

1. Squeegee Latch

2. Squeegee Hose and Tube

3. Squeegee Wheels (3)

4. Double Scrub Support Cable

5. Double Scrub Cable Hook

1

2

3

5

4

DISK / ORBITAL

86398220 Operators Manual - Chariot-2 iScrub 20

La page charge ...

Windsor Chariot 2 iScrub 20 Deluxe with ORB Technology Le manuel du propriétaire

Ce manuel convient également à

Windsor Chariot 2 iScrub 20 Deluxe with ORB Technology Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents