Windsor Chariot 2 iScrub 20 Le manuel du propriétaire

Catégorie
Scrubber
Taper
Le manuel du propriétaire
Register
your product
www.kaercher.com/welcome
86398220-H 10/31/19
Chariot 2 iScrub 20
English 02
From Serial Number (Ref No. 1*)
* See Serial Number page in Spare
Parts List or call manufacturer.
2 86398220 Operators Manual - Chariot-2 iScrub 20
Machine Data Label
Overview
The Chariot Scrubber is a battery powered, stand-on, hard floor scrubber intended for commercial use. The
appliance applies a cleaning solution onto a hard floor, scrubs the floor with brush or pad, and then vacuums the
soiled water back into the recovery tank.
Warranty Registration
Thank you for purchasing a Kärcher North America product. Warranty registration is quick
and easy. Your registration will allow us to serve you better over the lifetime of the product.
To register your product go to :
http://warranty.karcherna.com
For customer assistance:
1-800-444-7654
MODELS:
CS20 1.006-125.0
CSC20 1.006-133.0
CSX20 1006-137.0
CSXC20 1.006-138.0
CS22SP 1.006-130.0
CSC22SP 1.006-134.0
CSXM20 1.006-170.0
CSXCM20 1.006-171.0
CSM22SP 1.006-172.0
CSCM22SP 1.006-173.0
CSXBCM20 1.006-181.0
CSXBC20 1.006-182.0
CSXBM20 1.006-183.0
CSXB20 1.006-184.0
3
Table of Contents
Machine Data Label . . . . . . . . . . . . . . . . . . . . . . . . . .2
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .3
How To Use This Manual . . . . . . . . . . . . . . . . . . . . .4
Safety
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . .5
HAZARD INTENSITY LEVEL . . . . . . . . . . . . . . . . . .7
SAFETY LABEL LOCATIONS . . . . . . . . . . . . . . . . .9
Operations
Technical Specifications . . . . . . . . . . . . . . . . . . . . .10
How This Machine Works . . . . . . . . . . . . . . . . . . . .12
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Drive Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Scrub Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Scrub Controls - Squeegee. . . . . . . . . . . . . . . . . . .20
Scrub Controls - Solution Flow Rate. . . . . . . . . . . .22
Pre-Run Machine Inspection. . . . . . . . . . . . . . . . . .23
Starting Machine . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Emergency Stop Procedure . . . . . . . . . . . . . . . . . .23
Filling Solution Tank . . . . . . . . . . . . . . . . . . . . . . . .23
Normal Scrubbing . . . . . . . . . . . . . . . . . . . . . . . . . .24
To Begin Scrubbing . . . . . . . . . . . . . . . . . . . . . . . .24
Double Scrub . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Finish Removal (on select orbital models) . . . . . . .26
Emptying and Cleaning Tanks . . . . . . . . . . . . . . . .27
Models with Chemical Metering System . . . . . . . . .28
Maintenance
Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . .30
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Changing Batteries . . . . . . . . . . . . . . . . . . . . . . . . .36
Delta Q IC650 Charger Maintenance Instructions .37
Delta Q IC650 Charger Operating Instructions. . . .38
Charge Tracking Data. . . . . . . . . . . . . . . . . . . . . . .41
To Remove Squeegee Assembly . . . . . . . . . . . . . .42
Squeegee Blades-Cylindrical . . . . . . . . . . . . . . . . .43
Scrub Brush-Disk . . . . . . . . . . . . . . . . . . . . . . . . . .45
Scrub Brush-Orbital . . . . . . . . . . . . . . . . . . . . . . . .45
Finished Floors . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Replacing or Installing Scrub Brushes (Disk) . . . . .46
Replacing or Installing Scrub Pad (Orbital). . . . . . .46
Replacing or Installing Scrub Brushes (Cylindrical) 46
Removal or Installation of Debris Bin (Cylindrical) .47
To Replace Scrub Brush Motor - Disk . . . . . . . . . .48
To Replace Scrub Brush Motor - Orbital. . . . . . . . .48
Scrub Deck Actuator Removal / Replacement . . . .50
Circuit Protection. . . . . . . . . . . . . . . . . . . . . . . . . . .51
Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Tank Assembly Removal . . . . . . . . . . . . . . . . . . . .54
Drive Unit Removal . . . . . . . . . . . . . . . . . . . . . . . . .55
Vacuum & Float Shutoff . . . . . . . . . . . . . . . . . . . . .56
Vacuum Motor Carbon Brush Replacement . . . . . .57
Drive Motor-From Serial Number (4*) . . . . . . . . . . .58
Drive Motor Carbon Brush Replacement . . . . . . . .58
Drive Chain Tension . . . . . . . . . . . . . . . . . . . . . . . .58
Transporting Machine . . . . . . . . . . . . . . . . . . . . . . .58
Brake Override . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Inclines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Drive Motor-Prior to Serial Number(4*). . . . . . . . . .60
Drive Chain Tension . . . . . . . . . . . . . . . . . . . . . . . .60
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Inclines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Machine Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . .62
Machine Tie-Downs (Deluxe) . . . . . . . . . . . . . . . . .63
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Battery Discharge Indicator Troubleshooting . . . . .66
Suggested Spare Parts - Disk. . . . . . . . . . . . . . . . 67
Suggested Spare Parts - Orbital . . . . . . . . . . . . . . 68
Suggested Spare Parts - Cylindrical . . . . . . . . . . . 69
86398220 Operators Manual - Chariot-2 iScrub 20
4
How To Use This Manual
This manual contains the following sections:
HOW TO USE THIS MANUAL
SAFETY
•OPERATIONS
MAINTENANCE
The HOW TO USE THIS MANUAL section will tell you
how to find important information for ordering correct
repair parts.
Parts may be ordered from authorized dealers. When
placing an order for parts, the machine model and
machine serial number are important. Refer to the
MACHINE DATA box which is filled out during the
installation of your machine. The MACHINE DATA box
is located on the inside of the front cover of this manual.
The model and serial number of your machine is
located on the back of the machine.
The SAFETY section contains important information
regarding hazardous or unsafe practices of the
machine. Levels of hazards are identified that could
result in product damage, personal injury, or severe
injury resulting in death.
The OPERATIONS section is to familiarize the operator
with the operation and function of the machine.
The MAINTENANCE section contains preventive main-
tenance to keep the machine and its components in
good working condition. They are listed in this general
order:
Batteries
Scrub Brush
Squeegee
Service Schedule
Machine Troubleshooting
NOTE: The manual part number is located on the
lower right corner of the front cover.
Model:
Date of Purchase:
Serial Number:
Dealer:
Address:
Phone Number:
Sales Representative:
86398220 Operators Manual - Chariot-2 iScrub 20
5
Safety
IMPORTANT SAFETY INSTRUCTIONS
When using this machine, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
To reduce the risk of fire, electric shock, or injury:
Use only indoors. Do not use outdoors or expose to rain.
Use only as described in this manual. Use only manufacturer's recommended components and attachments.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to
an authorized service center.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
This machine is not suitable for picking up hazardous dust.
Do not operate this machine near flammable fluids, dust or vapors.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
Disconnect battery before cleaning or servicing.
Before the machine is discarded, the batteries must be removed and properly disposed of.
Make sure all warning and caution labels are legible and properly attached to the machine.
During operation, attention shall be paid to other persons, especially children.
Before use all covers and doors shall be put in the positions specified in the instructions.
When leaving unattended, secure against unintentional movement.
The machine shall only be operated by instructed and authorized persons.
When leaving unattended, switch off or lock the main power switch to prevent unauthorized use.
Only chemicals recommended by the manufacturer shall be used.
This appliance has been designed for use with the brushes specified by the manufacturer. The fitting of other
brushes may affect its safety.
Do not use on surfaces having a gradient of over 10% (6 degrees).
READ AND SAVE THESE INSTRUCTIONS
86398220 Operators Manual - Chariot-2 iScrub 20
6
Safety
MESURES DE SÉCURITÉ IMPORTANTES
Lors de l'utilisation d'un appareil à batteries, il est nécessaire de respecter
systématiquement des mesures de sécurité de base, comme suit :
PRENEZ NOTE DE TOUTES CES MESURES AVANT D'UTILISER CETTE MACHINE.
Pour réduire les risques d'incendie, de chocs électriques, ou de blessures :
N'utiliser cette machine qu'en intérieur. Ne jamais l'utiliser à l'extérieur ou dans la pluie.
Utiliser cet appareil conformément aux instructions du présent manuel uniquement. N'utiliser que les composants
et les accessoires conseillés par le fabricant.
Lorsque la machine ne fonctionnant pas correctement, a fait l'objet d'une chute ou d'une détérioration, a été laissée
à l'extérieur, est tombée dans l'eau, la retourner au centre de service agréé.
Ne pas opérer la machine lorsque les conduits de ventilation sont bloquées. Débarrasser les débris des conduits,
car ils peuvent réduire l'écoulement d'air.
Cette machine n'est pas adaptée au ramassage de poussières dangereuses
Ne pas l'utiliser près de liquides, de poussières ou de vapeurs inflammables.
L'entretien et les réparations de la machine doivent être effectuées par un personnel qualifié.
Si de la mousse ou du liquide sort de la machine, la mettre hors tension immédiatement.
Déconnecter les batteries avant de nettoyer la machine ou de la soumettre à un entretien.
Avant de se débarrasser de la machine, il est nécessaire de retirer les batteries et de les jeter correctement.
S'assurer que toutes les plaques d'avertissement ou de précaution sont lisibles et fixées correctement sur la
machine.
Durant la manoeuvre de la machine, prendre garde aux personnes environnantes et notamment aux enfants.
Avant l'utilisation de la machine, veiller à positionner tous les couvercles et portes comme indiqué dans les instruc-
tions.
Lorsque la machine est laissée sans surveillance, s'assurer qu'elle ne se déplace pas de manière accidentelle.
Cette machine ne doit être manoeuvrée que par un personnel expérimenté et qualifié.
Lorsque la machine est laissée sans surveillance, la mettre hors tension ou verrouiller l'interrupteur principal afin
d'empêcher un emploi non autorisé.
Seuls les produits chimiques recommandés par le fabricant doivent être utilisés.
Cette machine a été conçue pour être utilisée avec des brosses spécifiées par le fabricant.
L'utilisation d'autres brosses peut affecter sa sûreté.
N'employez pas sur des surfaces ayant un gradient de plus de 10% (6 degrés).
CONSERVER CES INSTRUCTIONS
86398220 Operators Manual - Chariot-2 iScrub 20
7
Safety
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY.
The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating
condition. Following is information that signals some potentially dangerous conditions to the operator or the equip-
ment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the
machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use
approved replacement parts.
Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep battery
compartment open during charging. Keep sparks and flames away from the batteries. Do not smoke
around batteries.
Disconnect batteries before working on machine. Only qualified personnel should work inside machine.
Always wear eye protection and protective clothing when working on or near batteries. Avoid skin contact
with the acid contained in the batteries.
Never allow metal to lie across battery tops.
86398220 Operators Manual - Chariot-2 iScrub 20
8
Safety
Les symboles ci-dessous sont utilisés à travers ce manuel comme illustré dans leurs descriptions :
DEGRÉS DE RISQUES EN CAS DE DANGER
Il existe trois degrés de risques identifiés par les termes signalétiques -AVERTISSEMENT et ATTENTION et POUR
VOTRE SÉCURITÉ. Le degré de risque est défini de la manière suivante:
AVERTISSEMENT - Dangers ou méthodes dangereuses qui POURRAIENT provoquer de graves blessures ou
entraîner la mort.
ATTENTION - Dangers ou méthodes dangereuses qui pourraient provoquer des blessures légères ou une détério-
ration du produit ou des biens immobiliers.
POUR VOTRE SÉCURITÉ: ce signe permet d'identifier les mesures de précaution à prendre pour assurer un bon
fonctionnement du matériel.
Rendre compte immédiatement d'une défaillance ou d'une détérioration de la machine. Ne pas utiliser la machine
si celle-ci ne fonctionne pas correctement. Lire soigneusement les informations ci-dessous signalant certains
dangers potentiels pour l'opérateur de la machine. L'opérateur doit être absolument au courant de ces dangers
potentiels. Localiser tous les dispositifs de sécurité sur la machine. Il est conseillé de prendre les mesures néces-
saires pour former le personnel opérateur.
POUR VOTRE SÉCURITÉ:
NE PAS MANOEUVRER LA MACHINE:
Lorsqu'on n'est pas expérimenté ou qualifié.
Lorsque le guide d'utilisation n'est pas été lu ou compris.
Dans des zones inflammables ou explosives.
Dans des zones où des objets peuvent tomber.
LORS DE L'ENTRETIEN DE LA MACHINE:
Éviter les parties amovibles. Ne pas porter de vêtements amples, tels que des vestes, des chemises ou des
vêtements avec manches lors de l'utilisation de la machine. Utiliser les pièces détachées homologuées.
Les batteries émettent le gaz d'hydrogène. L'explosion ou le feu peut résulter. Étincelles de subsistance et
flamme nue loin. Compartiment de batterie de subsistance ouvert en chargeant. Étincelles et flammes de
subsistance loin des batteries. Ne fumez pas autour des batteries.
Déconnecter les batteries avant de travailler sur la machine. La machine ne doit être confiée qu'à un
personnel qualifié. Porter systématiquement des lunettes et des vêtements de protection lors d'une inter-
vention sur les batteries ou aux alentours. Éviter tout contact de la peau avec l'acide contenu dans les
batteries.
Ne jamais placer d'objets métalliques sur le dessus des batteries.
86398220 Operators Manual - Chariot-2 iScrub 20
9
Safety
SAFETY LABEL LOCATIONS
These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible,
promptly replace them.
EMPLACEMENT DE L'ÉTIQUETTE DE SÉCURITÉ
REMARQUE : Ces dessins indiquent l'emplacement des étiquettes de sécurité sur la machine. Si, à tout moment,
les étiquettes deviennent illisibles, contactez votre représentant autorisé pour un remplacement rapide.
CAUTION
BATTERY
86252520
WARNING LABEL
86244300
CAUTION
CAUTION LABEL
86244310
CAUTION LABEL
86335010 (1X)
LABEL
WARNING
86385070
CAUTION LABEL
86335010
(ON BOARD CHARGER
MODELS ONLY)
CAUTION LABEL
86335010
(1X ON DISK DECK)
(2X ON ORBITAL DECK)
86398220 Operators Manual - Chariot-2 iScrub 20
10
Operations
Technical Specifications
ITEM DIMENSION/CAPACITY
Nominal Power-Disk 1080 W
Nominal Power-Orbital 936 W
Nominal Power-Cylindrical 1512 W
Rated Voltage 36 Volts DC
Rated Amperage -Disk 30 amps
Rated Amperage -Orbital 26 amps
Rated Amperage -Cylindrical 42 amps
Batteries 3 X12 Volt 130 AH @ 20 hr. rate
Battery Compartment Dimensions 20-1/2 in. x 13 in. x 10 in. tall (330mm x 521mm x 254mm)
Scrub Brush Motor - Disk Machine 1 x .28 HP (209 W)
Scrub Brush Motor - Orbital Machine 1 x .5 HP (373 W)
Scrub Brush Motor - Cylindrical Machine 1 x .8 HP (600 W)
Vacuum Motor .63 HP (470 W)
Maximum flow rate of vacuum motor 72 cfm (33.98 liters per second)
Maximum suction of vacuum motor 47.3 inches of water (11.7 kPa)
Propelling Motor .38 HP (280 W)
Mass (GVW) 827 lbs (375 kg)
Weight empty without batteries - Disk 209 lbs (96 kg)
Weight empty without batteries - Orbital 271 lbs (123 kg)
Weight empty without batteries - Cylindrical 255 lbs (116 kg)
Solution Control Gravity, 1/3 GPM average
Solution capacity 10 gal (38 L)
Recovery capacity 10 gal (38 L)
Scrub brush diameter - Disk 20 inch (508 mm)
Scrub brush length - Cylindrical 22 inch (559 mm)
Scrub brush pressure - Disk / Orbital 50 lbs (222N)
Scrub brush pressure - Cylindrical 46 lbs (21 kg)
Scrub brush speed - Disk 180 rpm
Scrub brush speed - Cylindrical 1500 rpm
Tires 8 in. (203mm) drive, 6 in. (156mm) rear, polyurethane
Maximum Speed 2.4 mph (3.7 kph)
Brake Electrical parking brake,sets automatically whenever operator stops.
Minimum aisle u-turn width 51in. (1295 mm)
Maximum rated climb and descent angle 10% (6 degrees)
Vibration, hands - Disk 1.6 m/s²
Vibration, feet - Disk 0.54 m/s²
Uncertainty - Disk 0.5 m/s²
Sound pressure level - Disk 68.0 dBA
Sound power level - Disk 81.1 dBA
Uncertainty - Disk 3.0 dBA
Vibration, hands - Cylindrical 1.5 m/s²
Vibration, feet - Cylindrical 0.9 m/s²
Uncertainty - Cylindrical 0.5 m/s²
Sound pressure level - Cylindrical 71.5 dBA
Sound pressure level - Cylindrical 84.7 dBA
Uncertainty - Cylindrical 3.0 dBA
86398220 Operators Manual - Chariot-2 iScrub 20
11
Operations
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure
that they do not play with the appliance.
Cet appareil n'est pas prévu à l'usage des personnes (enfants y compris) avec des possibilités physiques, sensori-
elles ou mentales réduites, ou le manque d'expérience et de connaissance, à moins qu'ils aient été donnés la
surveillance ou l'instruction au sujet de l'utilisation de l'appareil par une personne chargée de leur sûreté. Des
enfants devraient être dirigés pour s'assurer qu'ils ne jouent pas avec l'appareil.
ITEM MEASURE
Height 51.8 in (1316mm)
Length 44.0 in (1118mm)
Width without squeegee - Disk / Orbital 23.4 in (594mm)
Width without squeegee - Cylindrical 25.4 in (645mm)
Width of squeegee - Disk / Orbital 27.2 in (691mm)
Width of squeegee - Cylindrical 29.3 in (744mm)
Width of scrub path - Disk / Orbital 20 in (508mm)
Width of scrub path - Cylindrical 22 in (559mm)
WIDTH
LENGTH
HEIGHT
86398220 Operators Manual - Chariot-2 iScrub 20
12
Operations
How This Machine Works
The Chariot® is a battery powered, self-propelled, hard
floor scrubber intended for commercial use. The
appliance applies a cleaning solution onto a hard floor,
scrubs the floor with a brush, and then vacuums the
soiled water back into the recovery tank.
The machine's primary systems are the solution
system, scrub system, recovery system, and operator
control system.
The function of the solution system is to store cleaning
solution and deliver it to the scrub system. The solution
system consists of the solution tank, strainer, metering
valve and solenoid valve. The solution tank stores
cleaning solution (water and detergent) until it is
delivered to the scrub system. The strainer protects the
valves from debris. The solenoid valve automatically
prevents solution flow unless the scrub brush is turned
on and the machine is being propelled.
The function of the scrub system is to scrub the floor.
The disk scrub system consists of one rotary type disk
scrub brush, motor, scrub deck skirt and lift actuator.
The brush scrubs the floor as the motor drives the
brush. The brush drive hub allows the scrub brush to
follow irregularities and changes in the floor without
losing contact with the floor. The scrub deck skirt
controls the cleaning solution on the floor so that the
squeegee can pick it up.
The cylindrical scrub system consists of two cylindrical
brushes, motor, side squeegees, and lift actuator. The
two counter rotating brushes scrub the floor, driven by a
single motor. The brush deck “floats” with constant
brush pressure. The side squeegees keep the cleaning
solution within the brush deck width, allowing the main
squeegee to pick the solution up.
The function of the recovery system is to vacuum the
soiled water back into the recovery tank. The recovery
system consists of the squeegee, vacuum motor, float
ball, recovery tank. The squeegee wipes the dirty
solution off the floor as the machine moves forward.
The vacuum motor provides suction to draw the dirty
solution off the floor and into the recovery tank. The
float ball filter protects the vacuum fan from debris and
foam. The recovery tank stores the dirty solution.
The function of the operator control system is to control
the direction and speed of the machine. The directional
control system consists of the direction control drive
reset switch, throttle pedal, emergency stop/brake
switch, steering wheel, propel controller, and drive
wheel. The directional control drive reset switch signals
forward or reverse direction and makes sure the
operator is on the platform before machine will propel.
The controller interprets signals from the throttle pedal
to command the drive wheel to propel or slow the
machine. The steering wheel points the drive wheel in
the direction desired by the operator. The parking brake
automatically engages when the operator stop the
machine. The emergency stop/brake can be used to
hold the machine on slopes.
86398220 Operators Manual - Chariot-2 iScrub 20
13
Operations
Components
1. Drive Control
2. Scrub Controls
3. Control Console
4. Pedal Platform
5. Solution Tank
6. Recovery Tank
7. Recovery Sight Dome
8. Recovery Drain Hose
9. Scrub Deck Skirt
10. Solution Cover
11. Solution Drain Hose/Solution Level Indicator
12. Squeegee
86398220 Operators Manual - Chariot-2 iScrub 20
Cylindrical
Deluxe Disk & Cylindrical
12
10
9
10
12
1
2
3
4
5
6
7
8
9
11
14
Operations
Drive Controls
1
2
3
4
5
6
7
8
9
10
86398220 Operators Manual - Chariot-2 iScrub 20
15
Operations
1. Key Switch
2. Emergency Stop/Brake Switch
3. Directional Control / Drive Reset Switch
4. Throttle Pedal
5. Horn Button
6. Steering Wheel
7. Speed Control
8. Battery Discharge Indicator
9. Hour Meter
10. Operator Presence Switch
1. KEY SWITCH
Controls the power for machine functions.
To turn the machine power on, rotate key clock-
wise.
To turn the machine off, rotate key counterclock-
wise.
When the key is turned on the battery symbol will
flash once and stay on continuously.
2. EMERGENCY STOP/BRAKE SWITCH
This safety feature is designed to cut all power to
the machine at any time and apply parking brake.
To shut the machine power off, push the
Emergency Stop Switch, this will also engage the
parking brake and cause the machine to stop
immediately.
To reset the machine, rotate the switch clockwise.
3. DIRECTIONAL CONTROL / DRIVE RESET
SWITCH
This safety feature is designed to ensure safe
engagement of propel drive. Each time the
machine power is turned on, or each time an
operator steps on to the platform, the Drive Reset
Switch must be pushed before machine will propel.
The switch controls the direction of travel of the
vehicle. The lighted arrow on the switch indicates
direction of travel.
To travel forward, press the top of the switch.
To travel in reverse, press the bottom of the switch.
86398220 Operators Manual - Chariot-2 iScrub 20
16
Operations
4. THROTTLE PEDAL
Controls the speed of the vehicle within the speed control setting selected. Pressing the pedal causes the
machine to travel in the direction selected by the Directional Control Switch.
To increase speed, increase pressure on the pedal.
To decrease speed, decrease pressure on the pedal.
5. HORN BUTTON
The horn is activated by pressing the horn button.
6. STEERING WHEEL
The steering wheel turns the front wheel causing the machine to change direction.
7. SPEED CONTROL
Controls the maximum speed of the machine. There are two settings, slow and fast.
To change speed, rotate the dial to either slow or fast position. The slow position is to the left (counterclock-
wise), fast to the right (top position).
The throttle pedal will always regulate the speed between 0 and maximum.
86398220 Operators Manual - Chariot-2 iScrub 20
17
Operations
8. BATTERY DISCHARGE INDICATOR
Indicates the charge level of the batteries.
The indicator will be illuminated if the batteries have a sufficient charge. A slow, continuous flash indicates the
batteries require charging.
The Battery Lockout function will activate when the batteries are low.
Once active, the LED status indicator will begin to flash slowly and the controller will inhibit the scrub motor and
water solenoid. The vacuum and drive remain functional. The “vacuum only” selection (position ‘B’) can be
used to vacuum up any remaining water. Return the unit to the charging station and charge the batteries.
NOTE: Continuing usage may damage the batteries.
When the machine is left overnight with less than a full charge, the display may initially indicate a full charge. It
will also indicate a full charge if the batteries are disconnected, then reconnected. After a few minutes of
operation the indicator will give the correct charge level.
9. HOUR METER
Records the number of hours the machine has been in scrubbing operation. This information is useful in deter-
mining when to service the machine.
86398220 Operators Manual - Chariot-2 iScrub 20
18
Operations
Scrub Controls
1. FUNCTION MODE SWITCH
The first two positions are for transport only. See drive controls section.
Light cleaning
This mode is used for light cleaning. In this mode the machine will propel at fast speed. The
‘floating’ scrub deck and squeegee is in the down position. The water will flow. Water will auto-
matically shut off in neutral and restarts when scrubbing is resumed. The vacuum will draw the
water into the recovery tank.
Deep cleaning
This mode is used for deep cleaning. In this mode the machine will propel at a low speed. The
‘floating’ scrub deck and squeegee is in the down position. The water will flow. Water will auto-
matically shut off in neutral and restarts when scrubbing is resumed. The vacuum will draw the
water into the recovery tank.
1
LABEL WITH CHEMICAL METERING OPTION.
LABEL WITH FINISH REMOVAL MODE.
86398220 Operators Manual - Chariot-2 iScrub 20
19
Operations
Vacuum only mode
This mode is used for picking up solution only. The brush and water will both be up and off. In
this mode the machine will propel at fast speed. The squeegee is lowered and the vacuum will
come on.
Double Scrub cleaning (with chemical metering on equipped models)
This mode is used for putting down solution and scrubbing without picking it back up. The
squeegee is set manually by connecting the two double scrub support cables. In this mode the
machine will propel at a slow speed. The scrub deck will lower. The solution will flow. The brush
and water will shut off when the machine is in neutral. They will resume when propelling is
resumed.
Light cleaning with chemical metering
Chemical dilution rate to be set by chemical metering selection switch.
Deep cleaning with chemical metering
Chemical dilution rate to be set by chemical metering selection switch.
Finish removal (on select orbital models)
This mode is used for removing floor finish without the use of chemicals. In this mode the
machine will propel at a very slow speed. The 'floating' scrub deck and squeegee are in the
down position. The water will flow while propelling and will automatically shut off in neutral.
Water flow rate is controlled by the flow shut-off valve. The vacuum will draw water into the
recovery tank.
86398220 Operators Manual - Chariot-2 iScrub 20
20
Operations
Scrub Controls - Squeegee
1. Squeegee Latch
2. Squeegee Hose and Tube
3. Squeegee Wheels (3)
4. Double Scrub Support Cable
5. Double Scrub Cable Hook
1
2
3
5
4
86398220 Operators Manual - Chariot-2 iScrub 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Windsor Chariot 2 iScrub 20 Le manuel du propriétaire

Catégorie
Scrubber
Taper
Le manuel du propriétaire

dans d''autres langues