Cub Cadet 13B726HD603 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur
Stanley Black & Decker Outdoor GmbH • Saarbrücken • Germany
G22
769-13003I
3
EN
FR
DE
NL
IT
ES
SV
DA
NO
FI
PT
EL
HU
PL
English ............................. 8
(Original operating instructions)
Français ............................. 19
(Notice d’instructions originale)
Deutsch ............................. 31
(Originalbetriebsanleitung)
Nederlands ........................... 42
(Originele gebruiksaanwijzing)
Italiano ............................. 53
(Istruzioni per l’uso originali)
Español ............................. 65
(Instrucciones de funcionamiento originales)
Svenska ............................. 77
(Originalbruksanvisning)
Dansk ............................. 88
(Originale driftsvejledning)
Norsk ............................. 99
(Originale driftsanvisningen)
Suomi ............................. 110
(Alkuperäinen käyttöohjekirja)
Português ............................ 121
(Instruções de serviço originais)
Ελληνικά............................. 133
(Αυθεντικές οδηγίες χειρισμού)
Magyar ............................. 145
(Eredeti üzemeltetési útmutató)
Polski ............................. 156
(Oryginalna instrukcja obsługi)
8
For your safety
EN
Contents
Identification plate information
These specications are very important for subse-
quent identication when ordering spare parts and
for customer service. You will nd the rating plate
under the driver’s seat. Copy all information stated
on the identication plate into the following space.
You can nd these and further details on the device
in the separate CE declaration of conformity, which
is a constituent part of this operating manual.
For your safety
Use the device properly
This device is designed to be used
- as a riding mower for mowing lawns of houses
and gardens.
- with accessories which are approved expressly for
use with this lawn tractor,
- In accordance with the descriptions and safety
instructions given in these operating instructions.
Any other use is not an intended use. Improper use
is not covered by the warranty and the manufacturer
will reject any liability. The user is liable for all inju-
ries to third parties and damage to their property.
Unauthorised changes to the device exclude liability
of the manufacturer for any resulting damage and/
or injury.
This mower is not licensed for use on public roads
or for transporting people.
General safety instructions
Before operating the appliance for the rst time,
please read these operating instructions carefully
and act accordingly.
Inform other users how to operate the machine
properly.
Operate the mower only in the technical condition
in which it has been provided and delivered by the
manufacturer.
Keep these operating instructions in a safe place
where they are readily available whenever the
machine is used. If the device changes ownership,
hand over the operating manual with it.
Spare parts and accessories must satisfy the
requirements specied by the manufacturer.
Therefore only use original spare parts and original
accessories or spare parts and accessories that
have been authorised by the manufacturer.
Arrange for repair work to be carried out by a spe-
cialist workshop only.
Before working with the device
Do not use the device if you are tired or ill.
Any person intending to use this device must not be
under the inuence of intoxicants such as alcohol,
drugs or medicines.
Persons under the age of 16 are not permitted to
operate this mower.
This device is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and/
or knowledge, unless they are under supervision or
have received instructions concerning how to use
the device by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the device.
Before you begin work, make sure that you are
familiar with all attachments and operating controls
as well as their functions.
Store fuel only in approved containers and never
close to sources of heat (e.g. stoves or hot-water
boilers).
Replace the exhaust unit, tank or fuel cap if they
become damaged.
Observe guidelines when connecting towed items
or attachments to the mower. Driving performance,
especially steering, braking capability, and overall
stability are aected by attachments, towed items,
ballast weights and the weight of a grass catcher
when full.
When working with the device
When working with or on the unit, wear appropri-
ate work clothes (e.g. safety boots, long trousers,
tight-tting clothing, goggles and hearing protection).
For your safety........................................................ 8
Assembly .............................................................. 10
Your mower at a glance .........................................11
Operation .............................................................. 12
Tips on lawn care ................................................. 14
Transporting ......................................................... 15
Cleaning/servicing ................................................ 15
Shutting down the unit .......................................... 17
Warranty ............................................................... 17
Information on the engine ..................................... 17
Troubleshooting .................................................... 18
9
For your safety
EN
Working without ear protection may result in loss of
hearing.
Do not operate the mower unless it is in perfect and
safe working order.
Never change the engine settings pre-congured in
the factory.
Do not rell the fuel tank while the engine is running
or still hot.
Only refuel the mower outside.
Prevent naked ames and spark formation, and do
not smoke.
Make sure that at all times there are no persons,
especially children, or animals in the working area.
Check the terrain on which the mower is to be used
and remove all objects which could be thrown out by
the mower. This will avoid endangering people and
damaging the mower.
Do not mow on slopes with an incline greater than
20%. Working on slopes is dangerous; the mower
may overturn or slip. Start o slowly and brake
gently on slopes. Keep the clutch engaged and
proceed slowly when driving downhill. Do not travel
across the face of a slope; always drive straight up
and down.
Operate this mower only in daylight or good articial
light.
The device is not licensed for transporting people.
Before carrying out any work on the mower
Protect yourself against injury. Before all work on
this device.
- Switch o the engine.
- Withdraw the ignition key.
- Actuate the parking brake.
- Wait until all moving parts have come to a stand-
still; the engine must have cooled down.
- Pull the spark plug connector o the engine so
that the engine cannot inadvertently start.
After working with the device
Do not leave the mower unattended until you have
turned o the engine, applied the parking brake and
removed the ignition key.
Safety devices
Safety equipment is designed for your protection
and must always be in functioning order.
You must never make any modications to safety
equipment or bypass their functions.
Safety features are:
Grass catcher/discharge flap/mulch locking
component
Fig. 6
These parts protect you from the cutting blade or
ejected objects. The device may only be operated
with attached grass catcher (a) connected to the
discharge duct (b), deector ap (c) or mulch locking
component (d).
Safety locking system
The safety locking system will only allow the engine
to start when
- The driver is sitting on the seat.
- the parking brake has been actuated,
- the direction-of-travel lever is set to "N",
- the discharge ap, the mulch locking component
or the discharge chute is tted,
- the cutter deck has been switched o.
The safety interlock system switches the engine
o as soon as the operator leaves his seat without
actuating the parking brake or switching o the
cutter deck.
The safety interlock system prevents mowing with-
out attached grass catcher (engine automatically
switches o).
If devices do not feature the OCR function or if the
OCR function is deactivated, the safety interlock
system will prevent reversing while the cutter deck is
switched on (automatic switching o of the motor).
Therefore, switch o the cutter deck before
reversing.
Symbols on the device
On the device you will nd various symbols as adhe-
sive labels. They have the following meanings:
Caution! Before switching on, read the
operating instructions!
Keep third parties out of the danger
area!
10
Assembly
EN
Injury hazard due to rotating blades or
other moving parts.
Injury hazard due to rotating blades
or other moving parts. Keep hands
and feet out of the openings when the
machine is running.
MAX 20%
Working on steep slopes can be
dangerous.
Injury hazard due to grass or solid
objects thrown out by mower.
Caution! Danger of explosion.
Battery acid/risk of chemical burns.
When getting on and o, never step
on the cutter deck.
Danger! Unintended activation.
Before working on the device, unplug
the spark plug connector. Keep your
hands and feet away from rotating
parts.
Before beginning any work on this
device, remove the ignition key and
observe all information contained in
these instructions.
3E
Old batteries must not be disposed of
with domestic waste.
Caution!
Wear safety goggles.
Danger! No re, sparks, naked ames,
nor smoking
Before tipping the device, remove the battery.
The mower may only be operated with attached grass
catcher connected to the discharge chute, discharge
ap or mulch locking component.
Ensure these symbols mounted on the unit remain
legible.
Replace damaged or illegible symbols.
Symbols in the operating instructions
The following symbols are used in these operating
instructions:
Danger
Draws your attention to sources of potential
danger associated with the task you are
undertaking at the time which constitute a
danger to persons.
Attention
Draws your attention to potential hazards
associated with the task you are undertaking
at the time which could result in damage to
the mower.
Note
This indicates important information and
application tips.
Disposal instructions
Dispose of packaging remnants, old mowers, etc. in
accordance with local regulations.
Location details
Whenever a location on the mower is specied (e.g.
left, right), this is always from the perspective of the
driver, sitting in the seat, and facing forward.
Assembly
Assembling the device
The assembly of the device is illustrated at the end
of the operating manual or on a supplementary
sheet. Your device may dier from the illustration in
certain details.
11
Your mower at a glance
EN
Putting the battery into operation
Danger
Risk of poisoning and injury from battery
acid
Wear safety goggles and protective gloves. Do not
allow battery acid to come into contact with skin.
If you get battery acid on your face or in your eyes,
wash o immediately with cold water and consult a
doctor.
If you accidentally swallow battery acid, drink plenty
of water and consult a doctor immediately.
Store batteries out of the reach of children.
Never tilt the battery, as battery acid may run out.
Hand over any remaining battery acid to your dealer
or to a waste management company.
Attention
Risk of re, explosion and corrosion
caused by battery acid and gases emitted
by battery acid
Immediately clean parts of the mower splashed
by battery acid. Battery acid is corrosive. Do not
smoke, keep burning and hot objects away.
Possible short-circuit when working on the battery
Do not place any tools or metal objects on the
battery.
Disconnect and connect the battery in the correct
sequence.
Only operate the battery with the battery-terminal
cover tted (depending on the model, as a cover ap
on the positive terminal or as a complete protective
battery cover) .
Disconnection
First disconnect the black cable (–), then the red
cable (+).
Connection
First connect the red cable (+), then the black
cable (–).
The battery is lled with battery acid and sealed at
the factory. But even a “maintenance-free” battery
needs servicing to ensure it has a certain service
life.
Keep the battery clean.
Avoid tipping the battery over Electrolyte liquid will
run out of even a “sealed” battery if it is tilted.
Before starting up the device for the rst time,
charge the battery using a 12V battery charger
(maximum charging current 1.1A) for a period of
12 to 14 hours.
After charging the battery, rst pull out the battery
charger plug, then disconnect the battery (see
also operating instructions for the battery charger).
Your mower at a glance
Caution! Damage to the device.
This rst describes the functions of the controls
and display elements. Do not execute any of these
functions yet!
Fig. 1
1 Lever for speed settings/parking brake
Speed (Figure 4a):
Low speed
= Lever to "1".
High speed
= Lever to "6" or "7" (optional).
Increase speed
= Adjust drive positions without actuating the
clutch/brake pedal.
Reduce speed
= Adjust drive positions by actuating the clutch/
brake pedal (depress halfway).
Parkingbrake(g.4b):
Actuate the parking brake: Fully depress clutch/
brake pedal, push lever for speed setting to .
Release the parking brake: Fully depress clutch/
brake pedal, push lever to a speed setting.
2 Clutch/brake pedal
Clutching = Depress pedal half way.
Braking = Depress pedal all the way.
Note
Is also used to activate/deactivate the park-
ing brake.
3 Cutting height adjustment lever
Using the lever set the dierent cutting height
levels (1 to max. 5 - depending on model).
Level 1 = Lowest cutting height - cutter deck all
the way down.
Level 5* = Highest cutting height - cutter deck all
the way up.
(* Depending on model. Highest number corre-
sponds to the highest cutting height.)
4 Tank contents display (depending on model)
The inspection window indicates the level of fuel
in the fuel tank (Figure 7).
5 Direction-of-travel lever
Do not make any adjustments until the device is
at a standstill. To do this, fully depress and hold
down the brake pedal.
Forwards = Lever to “F/
Idling = Lever to “N”
Reverse = Lever to “R/
12
Operation
EN
6 PTO lever
The PTO lever mechanically switches the cutter
deck on and o.
Switchothecutterdeck
= Press lever out of recess and pull all the way
backwards.
Switch on the cutter deck .
= Slowly press lever forwards and engage in
recess.
7 Ignition lock (depending on model)
Ignition lock
Fig. 5a
Starting: Turn the key to the right to
until the engine is running, then release. Key is
turned to .
Stopping: Turn the key to the left, to .
Ignition lock with OCR function (depending on
model)
Fig. 5b
This is an ignition lock with OCR function (= us-
er-controlled mowing in reverse).
Starting: Turn key to the right until the engine is
running, then release. The key at (normal)
allows mowing in the drive direction.
OCR position: Turn key to left from the normal
position to reverse mowing position and
press the switch (1). The indicator light (2) comes
on and indicates to the user that the device can
now mow in reverse and forward gear.
Stopping: Turn the key to the left, to .
8 Throttle
Set engine speed continuously.
Fast engine speed = .
Slow engine speed = .
9 Choke (depending on model)
To start a cold engine, pull out the choke (9a) or
set the throttle to position (9b).
10 Fuel cap
Refuel
11 Oilllerneck
Fill up the oil and check the oil level
12 Battery
13 Grass catcher
Pick up cuttings.
14 Discharge chute
Convey cuttings to the grass catcher.
15 Can holder
16 Hitch (depending on model)
Cannot be used unless grass catcher removed.
17 Fill level indicator (depending on model)
Operation
Follow the instructions in the engine handbook!
Danger
Risk of injury
No person, especially children, and/or animals
should be allowed to stand close to the mower while
it is in use. They could be injured by stones or simi-
lar objects that might be thrown out.
Children must never be allowed to operate the
mower.
Be particularly careful when mowing in reverse gear
(mowers with OCR switch). There must be nobody
in the working area of the unit.
Never empty the grass catcher attachment while the
cutter deck is running.
While emptying the grass catcher attachment, you or
other persons may be injured by ejected clippings.
When mowing on steep slopes, there is a risk of the
mower tipping over and you could be injured as a
result. Do not drive across the face of a slope, but
only straight up and down. The device should not
be driven on slopes with a maximum incline greater
than 20%. Do not turn the mower round while you
are still on the slope. If the ground is wet the mower
could slip due to reduced traction and overturn. Only
cut the grass when the ground is dry.
Excessive speed can increase the risk of an
accident.
When mowing closed to the lawn edges, maintain
a safe distance at all times e.g. close to particularly
steep slopes, trees, bushes and hedges.
Pay particular attention when you are travelling in
reverse while mowing at the same time.
Inspect the ground on which the device is going to
be used and remove any loose objects that could be
picked up and thrown out again by the device.
If the cutter strikes a foreign object (e.g. stone) or if
the mower starts vibrating unusually:
Immediately switch o the engine. Before continuing
to use the device, have it checked for damage by a
specialist workshop
When rotary mowing, never stand in front of the
grass discharge openings.
Never place your hands or feet on or under rotating
parts.
Switch o the engine and remove the ignition key
and the spark-plug connector before loosening
obstructions or removing blockages from the dis-
charge channel.
Do not use the mower in adverse weather condi-
tions, e.g. if there is a risk of rain or a storm.
Danger of carbon monoxide asphyxiation
Run the internal combustion engine outdoors only.
Danger of explosion and risk of re
Petrol vapour is explosive and petrol itself is
extremely ammable.
Fill up will petrol before you start the engine. Do not
remove the fuel cap while the engine is running or
if it is still hot. Fill the fuel tank only after the engine
has been switched o and allowed to cool down.
Prevent naked ames and spark formation, and do
not smoke. Only refuel the mower outside.
Do not start the engine if any petrol has been spilt.
Push the mower away from the area where the
petrol was spilt and wait until the petrol fumes have
evaporated.
To prevent a re hazard, keep the following parts
free from grass and leaking oil: Engine, exhaust, fuel
tank.
13
Operation
EN
Danger
Injury hazard due to defective mower
Do not operate the mower if it is not in perfect work-
ing order. Before operating the unit, always carry out
a visual inspection. Pay particular attention to safety
devices, the cutting mechanism and its supporting
brackets, operating controls and threaded connec-
tions, and check that they are not damaged and are
securely attached.
Replace damaged parts before operating.
Danger
Risk of injury
While the engine is running or hot, do not check,
inspect or service/adjust the mower.
Operating times
Comply with the national/municipal regula-
tions concerning the times when the appli-
ance may be used (if required, contact your
local authority).
Before operating the unit, always
Check:
all guards,
the engine oil level (see engine manual),
The fuel level,
the tyre pressure,
ventilation slots in the engine area for dirt and
grass clippings.
Fill up with fuel and check the oil level
Note
The engine has already been lled with oil at
the factory - please check the oil; if required
rell.
Fill up with lead-free petrol. See engine manual.
Fill fuel tank up to max. 2.5 cm below the lower
edge of the inlet nozzle.
Close fuel tank tightly.
Check the oil level. The oil level must be between
the “Full/Max.” and “Add/Min.” mark (Also see
engine manual).
Check tyre pressure
Note
For production reasons the tyre pressure
may be higher than required.
Check tyre pressure. If required, correct (see
section “Maintenance”):
- front: 1.0 bar
- rear: 0.7 bar
Adjusting the drivers seat
Fig. 2
Move seat to the required position.
Adjusting the steering wheel(depending
on model)
Fig. 3
Press the locking button and put the steering
wheel into the desired position (a, b, c).
Note
Ensure that the locking button engages
correctly!
Starting the engine
Note
Some models have no choke. The engine
is automatically set to the particular starting
process.
Turn on the fuel tap (if tted – see engine manual).
Sit on the driver’s seat.
Switch o and raise the cutter deck:
- Move PTO lever to the O position .
- Set cutting height adjustment lever to “5” (cutter
deck up).
Actuate the parking brake.
Move direction of travel lever to “N”.
Move throttle to .
If the engine is cold, pull out the choke or set the
throttle to .
Turn the ignition key to until the engine is
running (attempt to start the engine for max. 5
seconds, wait 10 seconds before attempting to
start the engine again).When the engine is
running, set the ignition key to / .
As soon as the engine is running, slowly push
back the choke/throttle until the engine is running
smoothly.
Stopping the engine
Move the throttle to the middle position.
Let the engine run for approx. 20seconds.
Set ignition key to .
Remove the ignition key.
Before leaving the mower, actuate the parking
brake.
Driving
Danger
Abrupt starting, sudden stopping, and driving at an
excessively high speed increases the risk of acci-
dents and may damage the device. Be particularly
careful when reversing. Never set/adjust the driver’s
seat while the unit is moving.
Caution! Damage to the device.
Never change the direction of travel without rst
bringing the mower to a standstill.
Start the engine as indicated.
14
Tips on lawn care
EN
Release the parking brake: Fully depress clutch/
brake pedal, push lever to a speed setting.
Move the direction of travel lever to the corre-
sponding position.
Slowly release the clutch/brake pedal, the unit
moves o.
Stopping the mower
Depress the clutch/brake pedal until the unit stops.
Mowing
In normal mode / (see Operation,
ignition lock): Before reversing the machine,
switch o and raise the cutter deck.
In reverse mowing mode (see Opera-
tion, ignition lock): Exercise extreme caution when
reverse mowing and do not activate unless
absolutely necessary.
Do not change direction when the mower is
coasting or driving.
Start the engine as indicated.
To ensure adequate power output, move the
throttle to .
Release the parking brake: Fully depress clutch/
brake pedal, push lever to a speed setting.
Move the direction-of-travel lever to “F”/ forwards.
Switch on the cutter deck:
- Switch on PTO .
Lower the cutter deck.
Slowly release the clutch/brake pedal, the unit
moves o.
Emptying the grass catcher
If grass cuttings are left lying on the ground or if
the ll level indicator (17, Fig. 1) indicates that the
basket is full:
Stop the mower.
Actuate the parking brake.
Switch o the cutting mechanism.
Fig. 10a
Pull grass catcher upwards using the rear handle
and empty.
or
Fig. 10b
Stop the engine and wait until all moving parts
have come to a standstill.
Remove the grass catcher.
Empty out the contents.
Re-attach the grass catcher.
General
When adjusting the cutting height and travel speed,
ensure that the mower is not overloaded.
To ensure problem-free mowing, the cutting height
and driving speed must be adjusted according to the
length, type and moisture of the clippings. If block-
ages occur, reduce the driving speed and increase
the cutting height.
Switching the device off
Stop the mower.
Step on the brake pedal and actuate the parking
brake.
Switch o and raise the cutter deck.
Move the throttle to the middle position.
After 20 seconds set ignition key to .
Remove the ignition key.
Note
Leave engine to cool down before placing
the mower in an enclosed space.
Accessories (optional)
Risk of injury from the cutter
Wear safety gloves.
Fig. 6
Mowing with side discharge
Accessories: Deector ap (c)
Set the cutting height adjustment lever to "1"
(cutter deck bottom).
Remove discharge duct (b).
Attach discharge ap (c).
Mulching
Accessories: Mulch locking part (d)
Set the cutting height adjustment lever to "1"
(cutter deck bottom).
Remove discharge chute (b).
Fit mulch locking part (d).
Note
Due to the safety interlock system, the
grass catcher (a) must also be attached
when mowing with side discharge or when
mulching.
Tips on lawn care
Here are some tips to help you keep your lawn look-
ing healthy and ensure uniform growth.
Mowing
A lawn is made up of various dierent types of
grass. If you mow more frequently, the grown of
strongly-rooting grasses is favoured resulting in
rm turf. If you only rarely mow the grass, you will
encourage the development of high-growing types of
grass and other weeds (e.g., clover and daisies).
The normal height of a lawn is approx. 4-5 cm.
15
Transporting
EN
Only 1/3 of the total height should be mown;
therefore cut 7–8 cm long grass to normal height.
Preferably do not cut the lawn shorter than 4 cm,
otherwise the turf will be damaged in a dry period.
If the grass has grown particularly high (e.g. during
a holiday period), cut it back to its normal height in
stages.
Mulching (using the accessories)
With mulching, the grass is cut into small pieces
(approx. 1 cm) during mowing and is left on the
ground. Lots of nutrients in the cut grass are
retained.
For the best possible result the grass must always
be kept short, see also section “Mowing”.
Follow the instructions for mulching below:
- Do not mow wet grass.
- Never cut more than 2 cm of the total grass
length.
- Mow slowly.
- Use maximum engine speed.
- Clean the cutter deck regularly.
Transporting
Drive the mower only short distances otherwise
transport it by vehicle. Transport the device on a
transport vehicle over long distances.
Note: The mower is not approved for public thor-
oughfares in accordance with national road legisla-
tion (StVO).
Short distances
Danger
Solid objects may be hit/propelled by the rotating
cutter deck causing damage.
Switch o the cutter deck before driving the
mower.
Long distances
Warning: Transport damages
The mode of transport used (e.g. transport vehicle,
loading ramp) must be in accordance with guide-
lines (refer to the respective operating instructions).
During transport the device must be secured against
slipping.
Environmental hazard due to leaked fuel
The device must not be tilted when it is transported.
Prepare a suitable transport vehicle.
Attach the loading ramp to the vehicle.
Manually push the mower in neutral onto the
loading surface.
Actuate the parking brake.
Secure the power tool against slipping.
Cleaning/servicing
Danger
Injury hazard if engine is started inadver-
tently
Protect yourself against injury. Before all work on
this device.
- Switch o the engine.
- Withdraw the ignition key.
- Actuate the parking brake.
- Wait until all moving parts have come to a stand-
still; the engine must have cooled down.
- Pull the spark plug connector o the engine so
that the engine cannot inadvertently start.
Caution
Do not clean the device with a high-pressure cleaner.
Cleaning
Note
After use, always thoroughly clean the mower.
- Park the mower on rm and level ground.
- Actuate the parking brake.
Cleaning the cutter deck
Danger
Injury hazard due to sharp cutting blades
Wear safety gloves.
Caution when cleaning the cutters.
Warning: Motor damage
The device must not be tilted to an angle greater
than 30°. This might cause fuel to run into the com-
bustion chamber and could lead to engine damage.
Raise the cutter deck fully.
Clean the cutting compartment with a scrubbing
brush, hand brush or cloth.
Cutters with cleaning nozzle (according to the
model)
Figure 9
Place the mower on an even surface free of debris,
stones, etc., and engage the locking brake.
1. Use a commercially available quick-release cou-
pling to attach a water hose. Turn on water.
2. Start the engine.
3. Lower the cutter deck, and switch on for a few
minutes.
4. Switch OFF the cutter deck and engine.
5. Detach the water hose.
Repeat steps 1 to 5 for the second cleaning nozzle
(if provided).
At the end of cleaning process (steps 1 to 5):
Raise the cutters to the top.
Start the engine, and switch on the cutter deck for
a few minutes to dry it.
16
Cleaning/servicing
EN
Cleaning the grass catcher
Remove and empty the grass catcher.
The grass catcher can be cleaned with a powerful
water jet, for example from a garden hose.
Allow the grass catcher to dry o completely be-
fore using it again.
Maintenance
Observe the servicing instructions in the engine
manual. At the end of the season, have the mower
inspected and serviced by a service centre.
Attention: Motor damage
Engine oil is hazardous to the environ-
ment
After changing the oil, take the waste oil to a waste
oil collecting point or to a waste disposal company.
Batteries are an environmental hazard
Do not throw used batteries away with domestic
waste. Hand over used batteries to your dealer or to
a waste management company. Remove the battery
before scrapping the mower.
Using jump leads
Danger
Never bridge a defective or frozen battery with jump
leads. Ensure that the devices and the jump lead
clips do not touch each other and that the ignitions
are switched o.
Connect the red jump lead to the positive ter-
minal (+) of the at battery and the donor battery.
Connect the black jump lead rst to the negative
terminal (-) of the donor battery. Connect the other
clip to the frame of the engine block of the vehicle
with the at battery (as far away from the battery
as possible).
Note
If the donor battery is installed in a vehicle,
this vehicle must not be started during the
jump starting process.
Start the vehicle with the at battery and actuate
the parking brake.
Disconnect the jump leads in reverse sequence.
Tyre pressure
Caution
Never exceed the maximum permitted tyre pressure
(see tyre wall). When pumping up the tyres, do not
stand in front of or over the tyre.
The recommended operating tyre pressure is:
- front: 1.0 bar
- rear: 0.7 bar
Excessive tyre pressure reduces the service life of
the tyres. Always check the tyre pressure before
driving.
After 5 operating hours
First engine oil change. See engine manual for
subsequent intervals. Use the oil channel (op-
tional, Fig. 8) to drain.
After 10 operating hours
Lubricate all rotating and bearing points (operating
lever, height adjustment of the cutter deck ...) with
several drops of light oil.
Clean battery terminals.
Every 25 operating hours
Lubricate all blade shafts, tensioning pulleys and
tensioning pulley holders via the grease nipples
using grease type 251H EP. Arrange for this work
to be carried out by a specialist workshop.
Apply multipurpose grease to the teeth on the
steering gear.
Lubricate the steering linkage with a few drops of
light oil.
Lubricate the wheel bearings and front wheel axes
with a multipurpose grease applied to the grease
nipples.
Every 50 operating hours
Dirt and grass remnants must be removed from
the drive gear by a specialist workshop.
If required
Charge the battery
If you are not using the device for a prolonged
period, removal of the battery from the device and
charging prior to storage is recommended, as well
as every 2 months during storage, and before start-
ing up the device again.
Note
Follow the instructions in the operating man-
ual for your battery charger.
17
Shutting down the unit
EN
Replace fuses
Replace defective fuses only with ones of an
equal rating.
Once a season
Apply multipurpose grease to the teeth on the
steering gear.
Lubricate the steering linkage with a few drops of
light oil.
Lubricate all rotating and bearing points (operating
lever, height adjustment of the cutter deck ...) with
several drops of light oil.
Clean the spark plug and check the gap between
the electrodes or replace the plug. See engine
handbook.
The rear axles must be lubricated with a spe-
cial-purpose (water-repellent) grease in a spe-
cialist workshop.
The cutting blade must be sharpened or replaced
by a specialist workshop.
Shutting down the unit
Attention
Material damage to the device
Only store the mower once the engine has cooled in
a clean and dry room or area.
During prolonged storage, e.g. in winter, ensure that
the device is protected against rust.
At the end of the season or if the unit will not be
used for longer than a month:
Clean the mower and grass catcher attachment.
Wipe all metal parts with an oily rag or spray them
with oil to protect them from rust.
Charge battery with a battery charger.
When shutting down the appliance for the winter,
remove the battery, charge it and store in a dry/
cool location (protected from frost). Charge the
battery every 4–6 weeks as well as before re-in-
stalling it.
Drain the fuel (outdoors only) and shut down the
engine as described in the engine manual.
Inate tyres according to the specications on the
tyre walls. If tyres have no specications on the
tyre walls, inate to a pressure of 0.9 bar.
Store the mower in a clean, dry room.
Warranty
The warranty rules issued by our company or the
importer apply to every country.
Under the terms of the warranty we will repair faults
on your device free of charge, insofar as material or
manufacturing defects are the cause.
To make a claim under warranty please contact your
seller or your nearest branch.
Information on the engine
The engine manufacturer is liable for all engine-re-
lated problems with respect to power, power mea-
surement, technical specications, warranty and
service. Information can be found in the owner’s/
user handbook supplied separately by the engine
manufacturer.
18
Troubleshooting
EN
Troubleshooting
Danger
Injury hazard if engine is started inadver-
tently
Protect yourself against injury. Before all work on
this device.
- Switch o the engine.
- Withdraw the ignition key.
- Actuate the parking brake.
- Wait until all moving parts have come to a stand-
still; the engine must have cooled down.
- Pull the spark plug connector o the engine so
that the engine cannot inadvertently start.
Faults which occur while you are using your mower
often have simple causes which you should know
and may be able to rectify yourself. If you are in any
doubt however, your specialist workshop will be
happy to provide assistance.
Problem Possible cause(s) Remedy
Starter does not turn. Safety locking system has
actuated. To start the engine, sit on the driver’s seat,
fully depress brake pedal or apply parking
brake. Switch o the cutting mechanism.
Attach grass catcher together with dis-
charge channel or discharge ap or mulch
locking part.
Battery not connected correctly. Connect red cable to the (+) battery termi-
nal and black cable to (–) battery terminal.
Discharged or low battery. Charge the battery.
Fuse has tripped. Replace fuse. If the fuse blows repeatedly,
determine the cause (usually a short-cir-
cuit).
Loose earth cable between
engine and frame. Connect earth cable.
Starter turns but engine does not
start. Choke and throttle in wrong
position. Pull out choke.
Move throttle to .
Carburettor not receiving any
fuel, fuel tank empty. Top up with fuel.
Defective or dirty spark plug. Check spark plug; see engine manual.
No ignition spark. Arrange for the ignition to be checked in a
specialist workshop.
Engine producing smoke. Too much oil in engine. Switch the device o immediately.
Check engine oil level.
Engine defective. Switch the device o immediately. Arrange
for a specialist workshop to check the
engine.
Strong vibrations. Damaged blade shaft or defec-
tive cutter. Switch the device o immediately. Defec-
tive parts must be replaced by a specialist
workshop.
Cutter deck does not discharge
grass or cuts unevenly. Engine speed too low. Increase throttle.
Travelling speed too high. Set to a lower travelling speed.
Cutting blade is blunt. Arrange for a specialist workshop to sharp-
en or replace the blade.
Engine is running, cutter deck
is not mowing. V-belt torn. The V-belt must be replaced in a specialist
workshop.
19
Pour votre sécurité
FR
Sommaire
Indications à propos de la plaque signa-
létique
Ces indications sont très importantes pour l’iden-
tication ultérieure de l’appareil en vue de la com-
mande des pièces de rechange de l’appareil et pour
le service après-vente. Vous trouverez la plaque
signalétique sous le siège du conducteur. Veuillez
reporter dans le champ ci-dessous toutes les indi-
cations gurant sur la plaque signalétique de votre
appareil.
Ces indications ainsi que d’autres indications à
propos de l’appareil gurent sur la déclaration de
conformité CE séparée, qui fait partie intégrante de
la présente notice d’utilisation.
Pour votre sécurité
Utilisation correcte de l'appareil
Cet appareil est destiné à servir
- de tondeuse autoportée pour tondre les surfaces
gazonnées du jardin de la maison et d'un jardin
d'agrément,
- avec des accessoires expressément homologués
pour cette tondeuse à gazon autoportée,
- conformément aux descriptions et aux consignes
de sécurité gurant dans les présentes instruc-
tions d'emploi.
Toute autre utilisation est non conforme. Toute
utilisation non conforme à la destination prévue
implique la perte de la garantie et le refus du fabri-
cant d'assumer une quelconque responsabilité.
L'utilisateur répond de tous les dommages causés
aux tiers et à leurs biens.
Les modications apportées arbitrairement à l'appa-
reil dégagent le fabricant de toute responsabilité à
l'égard des dommages en résultant.
Cet appareil n’est pas autorisé à fonctionner sur la
voie publique ni à transporter des passagers.
Consignes de sécurité générales
Avant la première utilisation de l’appareil, lisez atten-
tivement la présente notice d’utilisation dans son
intégralité et respectez toutes les consignes qu’elle
contient.
Informez les autres utilisateurs de son utilisation
correcte.
N’utilisez l’appareil que dans l’état technique prescrit
et livré par le fabricant.
Conservez soigneusement ce mode d'emploi et gar-
dez-le à portée de main pour chaque intervention.
En cas de changement de propriétaire, remettez-lui
également le mode d’emploi avec l’appareil.
Les pièces de rechange et les accessoires doivent
satisfaire aux exigences dénies par le fabricant.
N’utilisez donc que des pièces de rechange et
accessoires d’origine ou des pièces de rechange et
accessoires homologués par le fabricant.
Conez exclusivement les réparations à un atelier
spécialisé.
Avant le travail avec l’appareil
En cas de fatigue ou de maladie, il est interdit d’utili-
ser l’appareil.
Les personnes utilisant l’appareil ne doivent pas se
trouver sous l’emprise de substances psychoactives
(p. ex. alcool, drogues ou médicaments).
L’utilisation de cet appareil est interdite aux per-
sonnes âgées de moins de 16 ans.
Cet appareil n’est pas destiné à être utilisé par des
personnes (y compris les enfants) présentant des
capacités physiques, sensorielles ou mentales res-
treintes, ou en l’absence de l’expérience et/ou des
connaissances requises, sauf si elles sont surveil-
lées par une personne responsable de leur sécurité,
ou si elles ont reçu de sa part des instructions sur la
façon d’utiliser l’appareil.
Surveiller les enfants an de garantir qu’ils ne jouent
pas avec l’appareil.
Avant de commencer le travail, familiarisez-vous
avec tous les équipements et éléments de com-
mande ainsi que leurs fonctions.
Ne stockez le carburant que dans des récipients
autorisés à cet eet et jamais à proximité de sources
de chaleur (p. ex. fours ou accumulateurs d'eau
chaude).
En cas de détérioration, remplacez le tuyau d’échap-
pement, le réservoir de carburant ou le bouchon de
réservoir.
Accouplez les remorques ou appareils rapportés en
respectant les prescriptions.
Pour votre sécurité ............................................... 19
Montage................................................................ 22
Vue d’ensemble de votre appareil ........................ 22
Utilisation .............................................................. 23
Conseils pour l'entretien de la pelouse ................. 26
Transport .............................................................. 27
Nettoyage / Maintenance...................................... 27
Mise hors service.................................................. 29
Garantie ................................................................ 29
Information sur le moteur...................................... 29
Dérangements et remèdes ................................... 30
20
Pour votre sécurité
FR
Ces derniers, la remorque ou les poids de ballast
ainsi que les bacs de ramassage pleins inuencent
le comportement de conduite de l’appareil, notam-
ment sa maniabilité, sa capacité de freinage et sa
propension au renversement.
Pendant le travail avec l’appareil
Lorsque vous vous servez de l’appareil ou le mani-
pulez, portez des vêtements de travail appropriés
tels que des chaussures de sécurité, des pantalons
longs, des vêtements moulants, des lunettes de
protection et une protection auditive.
Le fait de travailler sans casque anti-bruit risque
d'entraîner une perte auditive.
Utilisez uniquement l’appareil à condition qu’il soit
dans un état technique irréprochable.
Ne modiez jamais les réglages du moteur précon-
gurés en usine.
Ne faites jamais le plein lorsque le moteur tourne ou
lorsqu'il est chaud.
Remplissez le réservoir uniquement en plein air.
Evitez toute amme nue ainsi que la production
d’étincelles et ne fumez pas.
Assurez-vous qu’aucune personne, notamment des
enfants, ni des animaux ne se trouvent dans la zone
de travail.
Examinez le terrain sur lequel doit passer le trac-
teur et retirez-en tous les objets susceptibles d’être
happés puis catapultés. Vous éviterez ainsi toute
mise en danger de personnes et tous dommages
sur l’appareil.
Ne tondez pas sur des pentes ayant une déclivité
supérieure à 20 %. Le travail sur les pentes est
dangereux ; l’appareil peut basculer ou glisser. Sur
les pentes, démarrer et freiner toujours le plus en
douceur possible, laisser le moteur embrayé dans
les descentes et rouler lentement. Ne roulez jamais
transversalement à la pente, mais toujours unique-
ment vers la montée et vers la descente.
Avec l’appareil, ne travaillez que de jour ou avec un
éclairage articiel susant.
L’appareil n’est pas homologué pour le transport de
personnes.
Avant tous les travaux sur l'appareil
Protégez-vous contre les blessures. Avant tous les
travaux sur cet appareil.
- Arrêtez le moteur.
- Retirez la clé de contact.
- Serrez le frein de stationnement.
- Attendre que toutes les pièces mobiles se soient
entièrement immobilisées ; le moteur doit avoir
refroidi.
- Débranchez la cosse de la bougie d'allumage
sur le moteur pour en empêcher tout démarrage
intempestif.
Après le travail avec l’appareil
Ne descendez de l’appareil qu’après avoir éteint
le moteur, serré le frein à main et retiré la clé de
contact.
Dispositifs de sécurité
Les dispositifs de sécurité servent à vous protéger
et doivent toujours être opérationnels.
Il vous est interdit de modier les dispositifs de
sécurité ou d’en contrer le fonctionnement.
Voici les dispositifs de sécurité :
Bac de ramassage d’herbe / clapet d’éjection /
pièce obturatrice pour le paillage
Fig. 6
Ces pièces vous protègent contre les blessures par
la lame ou par des objets catapultés. L'utilisation de
cet appareil est uniquement autorisée à condition
que le dispositif de récupération d'herbe (a) soit
monté en liaison avec le canal d'éjection (b) ou la
trappe d'éjection (c) ou la pièce obturatrice pour
paillage (d).
Système de coupure de sécurité
Le système de coupure de sécurité ne permet le
démarrage du moteur que
- si le conducteur a pris place sur son siège,
- le frein de stationnement est actionné,
- le levier inverseur du sens de roulage se trouve
sur « N »,
- le clapet d’éjection, la pièce obturatrice pour le
paillage ou le canal d’éjection sont montés,
- le mécanisme de coupe est désactivé.
Le système de coupure de sécurité éteint le moteur
dès que l’utilisateur quitte le siège sans actionner
le frein à main et sans désactiver le mécanisme de
coupe.
Le système de coupure de sécurité empêche de
tondre sans bac de ramassage d’herbe (coupure
automatique du moteur).
Sur les appareils sans fonction OCR ou avec fonc-
tion OCR désactivée, le système de coupure de
sécurité empêche toute marche arrière tant que le
mécanisme de coupe est activé (arrêt automatique
du moteur).
Pour cette raison, désactivez le mécanisme de
coupe avant la marche arrière.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168

Cub Cadet 13B726HD603 Manuel utilisateur

Catégorie
Tondeuses à gazon
Taper
Manuel utilisateur