JB F6-DP-308 F6-DP-250 AU/EU Refrigerant Recovery Unit Manuel utilisateur

TM WWW.JBIND.COM 800.323.0811 [email protected]

JB INDUSTRIES

CONNECT WITH US

OPERATING INSTRUCTIONS

FOR MODELS: F6-DP-250 AND F6-DP-250-AU

TO LEARN MORE

ABOUT THE F6-DP-250

SCAN HERE:

TABLE OF CONTENTS

SAFETY FIRST �� 3

PRODUCT SAFETY �� 3

RESPONSIBILITY �� 3

COPYRIGHT AND DECLARATION OF CONFORMITY �� 4

SAFETY PRECAUTIONS �� 5

SPECIFICATIONS, FEATURES AND WARRANTY �� 6

F6-DP-250 SPECIFICATIONS �� 6

WARRANTY �� 6

ANATOMY OF THE F6 �� 7

SETUP AND OPERATION �� 8

GETTING STARTED�� 8

STANDARD RECOVERY OPERATION �� 9

PURGING F6-DP-250 �� 10

PUSH-PULL OPERATION �� 11

COOLING THE RECOVERY TANK �� 11

SPECIAL OPERATING NOTES �� 12

MAINTENANCE ��13

TROUBLESHOOTING ��13

SERVICE ��14

TM2

JB INDUSTRIES

Thank you for buying the JB Industries F6-DP-250 Refrigerant Recovery Machine�

For optimal F6-DP-250 performance, read this manual carefully before use�

For additional questions or assistance, contact JB Industries�

USA: +1.800.323.0811 or sales@jbind.com

SAFETY FIRST

This symbol is intended to alert the presence of critical items regarding operating,

safety and maintenance (servicing) instructions in this manual�

PRODUCT SAFETY

F6-DP-250 is a recovery machine for a broad range of refrigerants� Recovering refrigerants

into separate storage tanks involves a process of gas compression� This results in high

pressures within the machine, the connecting hoses, and the storage tank�

High pressure systems can cause accident or injury if not handled properly,

and with care�

Refrigerant hoses must have shut-off devices within 30�5 cm (12 in�) of the ends, to reduce the

likelihood of refrigerant leakage to the atmosphere when changing tanks or setups�

RESPONSIBILITY

Do not use F6-DP-250 unless properly trained in the recovery process� Operation of

this machine by unqualiﬁed personnel is potentially dangerous�

3

JB INDUSTRIES

COPYRIGHT AND DECLARATION OF CONFORMITY

Reproduction or adaptation of any part of this manual without permission is unlawful�

This declaration is issued under the sole responsibility of the manufacturer

JB Industries, Inc� The object of the declaration is to certify that this equipment,

designed and manufactured by JB Industries, Inc�, is in conformity with the relevant

Community harmonization legislation� It has been constructed in accordance with good

engineering practice in safety matters in force in the Community and does

not endanger the safety of persons, domestic animals or property when properly

installed and maintained and used in applications for which it was made�

Equipment Description: F6-DP-250/F6-DP-250-AU

Refrigerant Recovery Machine

Applicable Directives: 2014/30/EU General EMC

2011/65/EU RoHS

2014/35/EU Low Voltage Directive

Applicable Standards:

Safety: EN 60335-1:2012/A11:2014

Household and similar electrical appliances –

Safety – Part 1: General requirements

Emissions: EN 55014-1:2006/A2:2011 / CISPR 14-1:2005/A2:2011

Electromagnetic compatibility – Requirements – for

household appliances, electric tools and similar

apparatus – Part 1: Emissions

RoHS: EN 50581:2013

Technical documentation for the assessment of

electrical and electronic products with respect to the

restriction of hazardous substances

CE Implementation Date April 20, 2016

Authorized Representative Dave Madden

Director of Manufacturing

Any questions relative to this declaration or to the safety of JB Industries products

should be directed, in writing, to the quality assurance department at JB Industries, Inc�,

601 North Farnsworth, Aurora, IL 60505�

TM4

JB INDUSTRIES

SAFETY PRECAUTIONS

Read this manual before using F6-DP-250 to become familiar with its speciﬁcations and

operation� Review the Safety Data Sheets (SDS) and the Temperature/Vapor Pressure

information for the proper safety and handling requirements regarding the refrigerants

being recovered�

Wear gloves, eye protection and foot protection when working on refrigeration systems�

Refrigerant vapor can be hazardous and its by-products can be lethal�

Motors and switches can generate sparks and can be especially dangerous in

ﬂammable environments� Work only in well-ventilated areas, with mechanical ventilation

that provides at least four air change rates per hour� Do not work in an enclosed

area without appropriate safety equipment� It may be necessary to install a separate

circulation fan�

Never use oxygen for leak detection� Oxygen can become an explosive mixture in the

presence of oil and pressure� Perform leak detection in accordance with recommended

practice only� For best results, use a refrigerant leak detector, such as JB Industries

Aurora or Prowler�

Never mix refrigerants� Use separate storage cylinders, hoses, and ﬁlters for each type

of refrigerant recovered� Store refrigerants in a cool, dry place�

Never overﬁll a storage container� Overﬁlled tanks can rupture and explode� Use a

refrigerant scale such as JB Industries ATLAS to prevent overﬁll�

When opening service or cylinder valves, open slowly, to ensure all connections are

secure and free of danger�

Disconnect power before moving or servicing F6-DP-250�

The risk of electric shock and exposure to hot compressor parts is possible if the

F6-DP-250 covers are removed� F6-DP-250 should only be opened by a qualiﬁed

technician who has been trained in basic electronics and refrigeration�

Use only the power cord supplied by JB Industries� If the cord is lost or damaged,

contact JB Industries for information on obtaining a replacement�

When connected to the F6-DP-250, extension cord wiring can overheat under

conditions of high current draw� If an extension cord is necessary, use the shortest

possible length and only size 14 AWG or larger for 115 V (ac) or 1�00 mm2 or larger

for 230 V (ac)�

Do not use F6-DP-250 near open containers of gasoline or other ﬂammable liquids�

This product is designed for use with refrigerants only� Only approved for use with

A1 (nonﬂammable) and A2L (mildly ﬂammable) refrigerants� Any other uses of this

product are not recommended by JB Industries and could result in personal injury�

Use of this product other than intended is done at the user‘s own risk�

5

JB INDUSTRIES

SPECIFICATIONS, FEATURES AND WARRANTY

F6-DP-250 SPECIFICATIONS

Refrigerants�� R-12, R-1234yf, R-134a, R-22, R-32, R-401A, R-401B,

R-401C, R-402A, R-402B, R-404A, R-407A, R-407B,

R-407C, R-408A, R-409A, R-410A, R-500, R-502, R-507

Power ��230 V (ac), 50/60 Hz, 5�5A

Protection �� High pressure switch cutoff at 550 PSI

(3�8 MPa, 38 bar) Compressor motor thermally protected

Pressure �� Low side design pressure 350 PSI (2�4 MPa, 24 bar)

High side design pressure 550 PSI (3�8 MPa, 38 bar)

Temperature �� Operating range 10 to 40°C (50 to 104°F)

Pollution degree ��2

Ingress protection ��IP20

WARRANTY

JB Industries warrants the F6-DP-250 Refrigerant Recovery Machine to be free from defects

of materials or workmanship for three years from the date of purchase� JB Industries does not

warrant any machine that has been subjected to misuse, negligence, or accident, or has been

repaired or altered by anyone other than JB Industries�

The compressor is warranted for a period of three years by the manufacturer� To keep this

warranty in force, a ﬁlter (included) must be used on the inlet port or hose at all times to

prevent particulates from entering the compressor� Failure to use the included ﬁlter will void the

compressor warranty�

JB Industries liability is limited to repairing or replacing, at its option, a defective machine or

part� If a defect arises, a valid claim must be received by JB Industries, with transportation

prepaid, no later than thirty (30) days after the warranty period expires� JB Industries will

determine whether the machine has malfunctioned due to defective materials or workmanship�

This warranty is in lieu of all other warranties, expressed or implied, whether of merchantability,

ﬁtness for a particular purpose, or otherwise� All such other warranties are expressly

disclaimed�

JB Industries shall have no liability in excess of the price paid to JB Industries for F6-DP-250,

plus return transportation charges prepaid� JB Industries shall have no liability for any

incidental or consequential damages� All such liabilities are excluded�

TM6

JB INDUSTRIES

F6 FEATURES

ANATOMY OF THE F6

Heavy-Duty Metal Handle with

Comfortable Rubber Grip

-Micro-Channel Condenser

for Industry Leading

Recovery Rates

-Large Fan for Superior

Heat Dissipation

-1 Full Horsepower Motor

-Powerful Dual Piston Compressor

-Circuit Breaker

-Simple Two-Valve Operation

Carrying Strap with

Shoulder Pad

Rugged Blow Molded

Outer Shell

Recessed Gauges

Sturdy Metal Knobs

Easy-to-Access

Filter

Detachable and

Replaceable Power

Cord for Easy

Maintenance

Self-Purge Without

Changing Hoses

7

JB INDUSTRIES

SETUP AND OPERATION

GETTING STARTED

Review the full contents of this manual before operating the F6-DP-250�

Failure to follow proper safety precautions can result in personal injury or death�

Do not use the F6-DP-250 unless properly trained in the recovery process�

1 Install the included ﬁlter on the inlet� F6-DP-250 has a female refrigerant ﬂare ﬁtting,

and connects with male ﬂare ﬁttings� Ensure the protective plugs are removed

from the ﬁlter�

2 Attach the hoses to the ﬁlter�

Do not use an adapter ﬁtting in place of a ﬁlter� Use of an adapter ﬁtting can

damage the valves and will void the warranty�

3 Attach a hose from the discharge valve to the recovery tank� Connect other hoses

between system components as shown in Figure 1 on page 9�

4 Connect the AC power cord to a circuit protected by an appropriately sized circuit

breaker� If an extension cord is absolutely necessary, make sure it meets the

following conditions:

• Length is not excessive

• Contains a safety ground wire

• Wire size 14 AWG or larger for 115 V (ac) or 1.0 mm2 or larger for 230 V (ac)

Overﬁlled tanks can rupture and explode� When operating in standard recovery or push-pull

mode, it is possible to overﬁll the tank� Use a refrigerant scale to ensure that the tank does not

exceed 80% of its capacity by weight� Check the tank weight before transporting�

Do not allow the F6-DP-250 to recover large amounts of liquid too quickly�

NOTE: During the refrigerant recovery process, when a signiﬁcant amount of liquid is

present and enters the recovery machine too quickly, it can sometimes be

referred to as a “liquid slug” or “slugging�”

A liquid slug can activate the High Pressure shutoff and prolong the refrigerant recovery

process� If the F6-DP-250 recovers large amounts of liquid too quickly (or a liquid slug is

present),

a loud knocking will sound from the compressor�

Compressor damage caused by recovering a large amount of liquid too quickly is not covered

by the compressor warranty�

Monitor the recovery process carefully� If the compressor begins to knock:

• Throttle the INLET valve clockwise, or

• Adjust the MANIFOLD gauge valves until the knocking stops.

TM8

JB INDUSTRIES

STANDARD RECOVERY OPERATION

1 Connect all cables and hoses as described in Setup and Operation on page 8�

NOTE: Make sure all connections are tight, and that the cables and

hoses do not interfere with the recovery process (See Figure 1).

2 Make sure the hose connecting the F6-DP-250 to the recovery tank is attached to

the LIQUID port (LP)�

3 OPEN the LP valve on the tank — Keep the VAPOR port CLOSED�

4 Rotate the INLET valve (V1) to CLOSE�

5 Set the PURGE/RECOVER valve (V2) to the RECOVER position�

6 Slowly rotate the LIQUID valve on the MANIFOLD gauge to OPEN� Make sure there

are no leaks�

7 Turn on F6-DP-250�

8 Monitor the inlet pressure (LP, Low Pressure Gauge) and slowly rotate the INLET valve

(V1) to OPEN�

The compressor may emit a knocking sound if the F6-DP-250 attempts to recover a

signiﬁcant amount of liquid� To prevent damage to the compressor, throttle the LIQUID

valve on the MANIFOLD gauge set, or the F6-DP-250 INLET valve (V1)�

9 Once the liquid has been recovered, transfer the remaining vapor; rotate the INLET

valve (V1) to OPEN� Make sure the LIQUID and VAPOR valves on the MANIFOLD

gauge are OPEN�

Figure 1 - Setup Procedure for Standard Refrigerant Recovery

9

JB INDUSTRIES

10 Continue to operate until the LP gauge indicates the required vacuum has been

obtained�

11 Turn off the F6-DP-250 and close the INLET valve (V1) — Wait ﬁve minutes�

If the MANIFOLD gauge indicates pressure has risen above 0 PSIG (0 bar), refrigerant is

still present�

• Open the INLET valve (V1) and turn on F6-DP-250.

• Run the F6-DP-250 until the required vacuum is reached again.

• Wait ﬁve minutes. Repeat this process until all refrigerant is removed and

pressure is 0 PSIG (0 bar), or less.

12 Immediately purge the F6-DP-250� Purging is necessary to remove any residual

refrigerant from inside the F6-DP-250 internal components as well as the hose from

the outlet to the recovery tank� Refer to Purging the F6-DP-250 and Figure 2 below�

PURGING F6-DP-250

1 While the F6-DP-250 is off, rotate the PURGE/RECOVER valve (V2) to PURGE�

See (See Figure 2).

2 Turn on the F6-DP-250 and slowly rotate the INLET valve (V1) to PURGE�

3 Run the F6-DP-250 and monitor the LP gauge until a vacuum of 20 In/Hg (0�7 bar)

or more is achieved�

4 Turn off the F6-DP-250 and immediately close the valves on the recovery tank�

Rotate the inlet valve (V1) to CLOSE�

The hose and the discharge port will contain a small amount of pressurized refrigerant�

Exercise care when removing this hose�

Figure 2 - Setup Procedure for Purging

TM10

JB INDUSTRIES

COOLING THE RECOVERY TANK

The F6-DP-250 can be used to pre-cool (or sub-cool) the recovery tank, if the head pressure

is too high to complete the recovery process� If the ambient pressure is too high, high head

pressure can occur when working with certain refrigerants that have a high vapor pressure�

NOTE: The recovery tank must contain ﬁve pounds or more of liquid,

to allow the pressure differential to develop�

Sub-cooling the tank before starting the recovery process may provide little or no beneﬁt�

If the recovery process stalls because of high head pressure, turn off the F6-DP-250, close the

hose valves, and reconﬁgure the setup as shown in (See Figure 4).

PUSH-PULL OPERATION

The push-pull recovery method is used to move large amounts of liquid refrigerant� During

this process, the recovery unit pulls vapor from the recovery cylinder and produces a high

pressure discharge gas that pushes liquid out of the HVAC system and back into the recovery

cylinder� Recovery rates above 15 pounds per minute can be achieved when using this

procedure�

NOTE: Do not attempt the push-pull process unless the system contains

at least 15 pounds (7 Kg) of liquid that can be easily isolated�

To prevent overﬁll, use the scale to make sure the tank does not surpass 80% capacity

by weight� Monitor the tank weight carefully as 80% capacity maybe reached quickly during

push-pull due to its rapid transfer�

Connect the refrigerant hoses (See Figure 3). A sight glass, not included, can help determine

when the liquid has been transferred and vapor remains�

Figure 3 - Setup Procedure For Push-Pull Method

11

JB INDUSTRIES

1 Rotate V2 on the F6-DP-250 to RECOVER and open the LIQUID and

VAPOR valves on the cylinder�

2 Turn on the F6-DP-250�

3 Rotate V1 to OPEN�

4 On the cylinder, throttle the ﬂow of liquid by slowly closing the LIQUID

valve to achieve a minimum pressure differential of 100 PSIG (0�7 MPa, 7 bar)

between the LP and the HP gauges�

NOTE: To prevent the HP cutoff switch from actuating, do not allow the

HP gauge to exceed 550 PSIG (3�8 MPa, 38 bar)�

5 Once the recovery tank is cold, turn off the F6-DP-250 and reconﬁgure the

setup for standard recovery� Repeat as needed�

SPECIAL OPERATING NOTES

During standard operation, the High Pressure switch will reset when the head pressure drops

below approximately 425 PSI (2�9 MPa, 29 bar), and the F6-DP-250 will restart automatically�

Figure 4 - Setup Procedure for Sub-Cooling Method

TM12

JB INDUSTRIES

MAINTENANCE

With minimal but important maintenance, the F6-DP-250 can provide many seasons of reliable

service� After each use, clean the F6-DP-250 with a damp cloth to remove dirt and oils�

Do not use gasoline or other hazardous solvents to clean F6-DP-250; this can damage

the plastic enclosure� Standard household detergent or isopropyl alcohol may be used,

but do not allow liquid to penetrate the outer case�

Make sure the inlet and discharge ports are protected during transit and storage; keep the

inner diameter and the outer threads clear and clean�

NOTE: For best results, leave the ﬁlter connected to the inlet port,

and change the ﬁlter regularly�

TROUBLESHOOTING

PROBLEM CAUSE ACTION

F6-DP-250 will not

turn on; compressor

does not start

1. Power cord is not attached

2. No voltage at receptacle

3. Circuit breaker has opened

4. Discharge pressure is too high;

HP switch has opened

5. Electronics failure in motor

1. Attach power cord

2. Verify voltage at job site

3. Identify cause of breaker

activation, rectify and reset

4. Reduce pressure; rotate V2 to

Purge, then back to Recovery

5. Factory service required

Compressor starts,

but falters within

minutes; pressure

indication on HP

gauge is high

1. Recovery tank valve is not open

2. Discharge hose blocked

3. Air in system/tank

1. Open tank valve

2. Check and clear blockage

3. Bleed air from system/tank

Compressor stops

intermittently

1. Vapor pressure of refrigerant in

tank is close to HP trip point

2. Thermal overload switch in

compressor is activating

1. Reduce tank temperature

2. Reduce amount of liquid being

pumped; let machine cool

before proceeding

13

JB INDUSTRIES

SERVICE

The F6-DP-250 uses electrical components recognized by international safety agencies or

components that have been specially designed for this application�

Do not change any of these components, as it could compromise safety� All service

work must be performed at a JB Industries-approved facility to maintain the safety rating

and the warranty�

If defective, do not return F6-DP-250 directly to the factory� For technical assistance or service

information, contact JB Industries or your wholesaler�

PROBLEM CAUSE ACTION

F6-DP-250 overheats Excessive head pressure, due to:

1. High ambient temperature

2. Restricted discharge hose

3. Air in recovery tank

1. Reduce tank temperature

2. Check and clear restriction

3. Bleed air from tank

Recovery process

too slow

1. Head pressure is too high

2. System refrigerant is frozen

3. Compressor seals are worn

1. Reduce tank temperature or

change tanks

2. Interrupt process to allow ice to

dissipate

3. Rebuild compressor with

service kit — contact wholesaler

for assistance

TM14

JB INDUSTRIES

THANK YOU FOR

PURCHASING

THE F6

TO SEE THE FULL LINE

OF JB PRODUCTS

VISIT US AT

JBIND.COM

DS-20000S

WIRELESS REFRIGERANT

CHARGING SCALE

PATRIOTTM 2-VALVE

MANIFOLD

KOBRA® CLE

SERIES HOSE

EMPTY REFRIGERANT

TANK CYLINDERS

15

JB INDUSTRIES

ÍNDICE

NORMAS DE SEGURIDAD� ��17

SEGURIDAD DEL PRODUCTO �� 17

RESPONSABILIDAD �� 17

COPYRIGHT Y DECLARACIÓN DE CONFORMIDAD �� 18

PRECAUCIONES DE SEGURIDAD ��19

ESPECIFICACIONES, FUNCIONES Y GARANTÍA ��20

ESPECIFICACIONES DE F6-DP-250 �� 20

GARANTÍA �� 20

ANATOMÍA DE LA F6 ��21

CONFIGURACIÓN Y FUNCIONAMIENTO ��22

PRIMEROS PASOS �� 22

FUNCIONAMIENTO DE LA RECUPERACIÓN ESTÁNDAR �� 23

PURGA DE F6-DP-250 �� 24

FUNCIONAMIENTO DEL MÉTODO PUSH-PULL �� 25

REFRIGERACIÓN DEL DEPÓSITO DE RECUPERACIÓN� �� 25

NOTAS SOBRE EL FUNCIONAMIENTO ESPECIAL �� 26

MANTENIMIENTO ��27

RESOLUCIÓN DE PROBLEMAS ��27

REVISIÓN ��28

TM16

JB INDUSTRIESJB INDUSTRIES F6-DP-250 INSTRUCCIONES DE FUNCIONAMIENTO

Le agradecemos que haya comprado el Equipo de recuperación de refrigerante F6-DP-250

de JB Industries� Para conseguir un rendimiento óptimo de F6-DP-250, lea este manual

detenidamente antes de usar el equipo�

Si tiene preguntas adicionales o necesita ayuda, póngase en contacto con JB Industries�

Estados Unidos: +1.800.323.0811 / sales@jbind.com

NORMAS DE SEGURIDAD

El objetivo de este símbolo consiste en advertir al usuario de la existencia de aspectos

importantes relacionados con las instrucciones de mantenimiento (revisión), seguridad

y funcionamiento de este manual�

SEGURIDAD DEL PRODUCTO

F6-DP-250 es un equipo de recuperación para una amplia gama de refrigerantes� La

recuperación de refrigerantes en depósitos de almacenamiento independientes implica un

proceso de compresión de gas que provoca altas presiones en el equipo, las mangueras de

conexión y el depósito de almacenamiento�

Los sistemas de alta presión pueden provocar accidentes o lesiones si no se

manipulan correctamente y con cuidado�

Las mangueras refrigerantes deben incluir dispositivos de parada a unos 30,5 cm

(12 pulgadas) de los extremos para reducir la probabilidad de fuga de refrigerante a la

atmósfera al cambiar los depósitos o las conﬁguraciones�

RESPONSABILIDAD

No utilice F6-DP-250 a menos que haya recibido la formación adecuada en el proceso

de recuperación� El uso de este equipo por parte de personal que no esté cualiﬁcado

puede ser peligroso�

17

JB INDUSTRIESJB INDUSTRIES

F6-DP-250 INSTRUCCIONES DE FUNCIONAMIENTO

COPYRIGHT Y DECLARACIÓN DE CONFORMIDAD

Es ilegal reproducir o adaptar cualquier parte de este manual sin permiso�

Por la presente se certiﬁca que este equipo, diseñado y fabricado por JB Industries Inc�,

601 N Farnsworth Ave; Aurora, IL 60505, EE� UU�, cumple los requisitos de seguridad

esenciales y se comercializa en el mercado de acuerdo con ellos� Se ha fabricado de

acuerdo con buenas prácticas de ingeniería en cuestiones de seguridad vigentes en

la Comunidad y no representa un peligro para la seguridad de las personas, animales

domésticos o propiedades siempre que se instale y se mantenga adecuadamente y se use

para las aplicaciones para las que está destinado�

Descripción del equipo: F6-DP-250/F6-DP-250-AU

Máquina de recuperación de refrigerante

Directrices aplicables: 2014/30/EU General EMC

2011/65/EU RoHS

2014/35/EU Directiva de bajo voltaje

Normas aplicables:

Seguridad: EN 60335-1:2012/A11:2014

Aparatos electrodomésticos y análogos -

Seguridad - Parte 1: Requisitos generales

Emisiones: EN 55014-1:2006/A2:2011 / CISPR 14-1:2005/A2:2011

Compatibilidad electromagnética - Requisitos - para

Electrodomésticos, herramientas eléctricas y similares

- Parte 1: Emisiones

RoHS: EN 50581:2013

Documentación técnica para la evaluación de

productos eléctricos y electrónicos en relación con la

restricción de sustancias peligrosas

Fecha de implantación de la CE 20 de Abril de 2016

Representante autorizado Dave Madden

Director de Fabricación

Todas las preguntas relacionadas con esta declaración o con la seguridad de los productos

de JB Industries se deben dirigir por escrito al departamento de garantía de calidad en la

dirección indicada anteriormente� 601 North Farnsworth, Aurora, IL 60505 (EE� UU)�

TM18

JB INDUSTRIES F6-DP-250 INSTRUCCIONES DE FUNCIONAMIENTO

JB INDUSTRIES

PRECAUCIONES DE SEGURIDAD

Lea este manual antes de utilizar F6-DP-250 para familiarizarse con sus especiﬁcaciones y

su funcionamiento� Revise las hojas de datos de seguridad (SDS)anipulación y seguridad

adecuados con relación a los refrigerantes que se van a recuperar�

Use guantes, gafas protectoras y calzado de seguridad cuando trabaje con sistemas

de refrigeración�

El vapor refrigerante puede ser peligroso y su inhalación a través de los productos

puede ser letal�

Los motores y conmutadores pueden generar chispas y ser especialmente peligrosos

en entornos inﬂamables� Trabaje solo en zonas que estén bien ventiladas, con

ventilación mecánica que proporcione al menos cuatro renovaciones de aire por

hora� No trabaje en un área cerrada sin el equipo de seguridad adecuado� Puede ser

necesario instalar un ventilador de circulación independiente�

No utilice nunca oxígeno para la detección de fugas� El oxígeno se puede convertir en

una mezcla explosiva en presencia de combustible y presión� Realice una detección de

fugas de conformidad únicamente con la práctica recomendada� Para obtener mejores

resultados, utilice un detector de refrigerante como, por ejemplo, JB Industries Aurora o

Prowler�

No mezcle nunca los refrigerantes� Utilice ﬁltros, mangueras y cilindros de

almacenamiento independientes para cada tipo de refrigerante recuperado� Almacene

los refrigerantes en un lugar frío y seco�

No llene nunca el contenedor de almacenamiento en exceso� Los depósitos llenados

en exceso pueden romperse y explotar� Utilice una balanza para refrigerante como, por

ejemplo, JB Industries ATLAS, para evitar el llenado excesivo�

Al abrir válvulas de cilindro o de mantenimiento, hágalo lentamente para garantizar que

todas las conexiones estén bien sujetas y fuera de peligro�

Desconecte la electricidad antes de mover F6-DP-250 o realizar tareas de

mantenimiento en el equipo�

Si se retiran las cubiertas de F6-DP-250, puede existir el riesgo de descarga eléctrica

y de exposición a las piezas calientes del compresor� F6-DP-250 solo debe abrirse

por un técnico cualiﬁcado que haya recibido formación en electrónica básica y

refrigeración�

Utilice únicamente el cable de alimentación proporcionado por JB Industries� Si el

cable se ha perdido o ha sufrido daños, póngase en contacto con JB Industries para

obtener información sobre cómo solicitar uno de recambio�

Al conectarse a F6-DP-250, los cables de extensión pueden sobrecalentarse en

condiciones de consumo alto de corriente� Si es necesario utilizar un cable de

extensión, utilice el que tenga la longitud más corta posible y un calibre mínimo de 14

AWG para una corriente de 115 V (CA) o de 1 mm2 para una corriente de 230 V (CA)�

No utilice F6-DP-250 cerca de contenedores abiertos de gasolina u otros líquidos

inﬂamables�

Este producto está diseñado para utilizarlo únicamente con refrigerantes� Solo está

aprobado para utilizarlo con refrigerantes de tipo A1 (no inﬂamables) y A2L (ligeramente

inﬂamables)� JB Industries no recomienda ningún otro uso para este producto, ya que

podría provocar daños personales; el uso del producto en situaciones diferentes a las

previstas queda bajo responsabilidad del usuario�

19

JB INDUSTRIESJB INDUSTRIES

F6-DP-250 INSTRUCCIONES DE FUNCIONAMIENTO

ESPECIFICACIONES, FUNCIONES Y GARANTÍA

ESPECIFICACIONES DE F6-DP-250

Refrigerantes �� R-12, R-1234yf, R-134a, R-22, R-32, R-401A, R-401B,

R-401C, R-402A, R-402B, R-404A, R-407A, R-407B,

R-407C, R-408A, R-409A, R-410A, R-500, R-502, R-507

Alimentación ��230 V (ac), 50/60 Hz, 5�5A

Protección ��Bloqueo del conmutador de alta presión en motor

de compresor de 550 PSI (3�8 MPa, 38 Bar) con protección térmica

Presión �� Presión de diseño lateral baja de 350 PSI, (2�4 MPa, 24 bar);

Presión de diseño lateral alta de 550 PSI (3�8 MPa, 38 bar)

Temperatura �� Intervalo de funcionamiento de 10 a 40 °C (de 50 a 104 °F)

Grado de contaminación ��2

Protección frente a polvo y líquido. ��IP20

GARANTÍA

JB Industries garantiza que el Equipo de recuperación de refrigerante F6-DP-250 estará libre

de cualquier defecto de fabricación o materiales durante un período de tres años a partir de la

fecha de compra� JB Industries no ofrece garantía para ningún equipo que se haya utilizado

de forma indebida, que haya sido dañado por negligencia o accidente, o que haya sido

reparado o alterado por cualquier persona ajena a JB Industries�

El fabricante ofrece una garantía de tres años para el compresor� Para mantener vigente

esta garantía, se debe utilizar un ﬁltro (incluido) en la manguera o en el puerto de entrada en

cualquier momento para evitar que las partículas entren en el compresor� Si no se utiliza el

ﬁltro incluido, se anulará la garantía del compresor�

La responsabilidad de JB Industries se limita, según considere oportuno, a la reparación o

sustitución del equipo o de la pieza defectuosos� Si se detecta un defecto, se debe enviar

una reclamación válida a JB Industries, con los gastos de transporte pagados previamente,

en un plazo no superior a treinta (30) días desde la fecha de vencimiento de la garantía� JB

Industries determinará si los problemas de funcionamiento del equipo se deben a defectos en

la fabricación o en los materiales�

Esta garantía sustituye a cualquier otra garantía, expresa o implícita, ya sea de

comerciabilidad, adecuación a un ﬁn especíﬁco o de cualquier otro tipo� Se renuncia

expresamente a cualquier otra garantía de este tipo�

JB Industries no asumirá ninguna responsabilidad superior al precio abonado a JB

Industries por F6-DP-250 más los gastos de transporte para la devolución que se abonaron

previamente� JB Industries no asumirá ninguna responsabilidad por daños derivados o

fortuitos� Se excluyen todas las responsabilidades de este tipo�

TM20

JB INDUSTRIES F6-DP-250 INSTRUCCIONES DE FUNCIONAMIENTO

JB INDUSTRIES

La page charge ...

JB F6-DP-308 F6-DP-250 AU/EU Refrigerant Recovery Unit Manuel utilisateur

JB F6-DP-308 F6-DP-250 AU/EU Refrigerant Recovery Unit Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents