MINN KOTA PowerDrive Installation Instructions Manual

ULTERRA™

BOW-MOUNT TROLLING MOTOR

INSTALLATION INSTRUCTIONS

2 | minnkotamotors.com

INTRODUCTION

Made by Minn Kota

Johnson Outdoors

Marine Electronics, Inc.

121 Power Drive

Mankato, MN 56001 USA

Trolling Motors

Produced in 2015

SER NO R365 MK12345

ULTERRA 80/US2/IPLINK-45"_BT

MODEL 1358923

NOTE: The serial number on your Ulterra is located

inside the mount near the motor rests.

EXAMPLE

THANK YOU

Thank you for choosing Minn Kota. We believe that you should spend more time ﬁshing and less time positioning your boat.

That’s why we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling

motor is thought out and rethought until it’s good enough to bear our name. Countless hours of research and testing provide you

the Minn Kota advantage that can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we

are never done helping you catch more ﬁsh.

MOTOR INFORMATION (FOR CUSTOMER REFERENCE ONLY)

Model: __________________________________________________________________________________________________________________________

Serial Number: ________________________________________________________________________________________________________________

Purchase Date: ________________________________________________________________________________________________________________

Store Where Purchased: _____________________________________________________________________________________________________

REGISTRATION

Remember to keep your receipt and immediately register

your trolling motor. A registration card is included with your

motor or you can complete registration on our website at

minnkotamotors.com.

SERIAL NUMBER

Your Minn Kota 11-character serial number is very important.

It helps to determine the speciﬁc model and year of

manufacture. When contacting Consumer Service or registering

your product, you will need to know your product’s serial

number. We recommend that you write the serial number

down so that you have it available for future reference.

NOTE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit.

You may obtain service by: calling Minn Kota at (800) 227-6433; returning your motor to the Minn Kota Factory Service

Center; sending or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is

available on our website, at minnkotamotors.com. Please include proof of purchase, serial number and purchase date for

warranty service with any of the above options.

minnkotamotors.com | 3

SAFETY CONSIDERATIONS

WARNING

You are responsible for the safe and prudent operation of your vessel. We have designed your Minn Kota product to be an

accurate and reliable tool that will enhance boat operation and improve your ability to catch ﬁsh. This product does not relieve

you from the responsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a

permanent watch so you can respond to situations as they develop. You must always be prepared to regain manual control of

your boat. Learn to operate your Minn Kota product in an area free from hazards and obstacles.

WARNING

Never run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected

from the power source when it is not in use or is oﬀ the water. When connecting the power-supply cables of the motor to the

battery, ensure that they are not kinked or subject to chafe and route them in such a way that persons cannot trip over them.

Before using the motor make sure that the insulation of the power cables is not damaged. Disregarding these safety precautions

may result in electric shorts of battery(s) and/or motor. Always disconnect motor from battery(s) before cleaning or checking

the propeller. Avoid submerging the complete motor as water may enter the lower unit through control head and shaft. If the

motor is used while water is present in the lower unit considerable damage to the motor can occur. This damage will not be

covered by warranty.

WARNING

Take care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects.

The motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming

and for ﬂoating objects. Persons whose ability to run the motor or whose reactions are impaired by alcohol, drugs, medication,

or other substances are not permitted to use this motor. This motor is not suitable for use in strong currents. The constant noise

pressure level of the motor during use is less than 70dB(A). The overall vibration level does not exceed 2,5 m/sec2.

Please thoroughly read the user manual. Follow all instructions and heed all safety and cautionary notices. Use of this motor

is only permitted for persons that have read and understood these user instructions. Minors may use this motor only under

adult supervision.

WARNING

When stowing or deploying the motor, keep ﬁngers clear of all hinge and pivot points and all moving parts. In the event of

unexpected operation, remove power leads from the battery.

WARNING

It is recommended to only use Johnson Outdoors approved accessories with your Minn Kota motor. Using non-approved

accessories including to mount or control your motor may cause damage, unexpected motor operation and injury. Be sure to use

the product and approved accessories, including remotes, safely and in the manner directed to avoid accidental or unexpected

motor operation. Keep all factory installed parts in place including motor and accessory covers, enclosures and guards.

4 | minnkotamotors.com

KNOW YOUR BOAT

Keel

Bow

Hull

Bow

Stern

Port

Port Starboard

Starboard

Gunwale

Transom

Inboard

Outboard

minnkotamotors.com | 5

INSTALLATION

INSTALLING THE ULTERRA

Your new Ulterra comes with everything you’ll need to directly install it to the boat. This motor can be directly mounted to the

boat or it may be coupled with a Minn Kota quick release bracket for ease of mounting and removal. For installation with a quick

release bracket, refer to the installation instructions provided with the bracket. For compatible quick release mounting bracket,

please visit minnkotamotors.com. To install the motor directly to the boat, please follow the instructions provided in this manual.

Please review the parts list, mounting considerations and tools needed for installation prior to getting started. For additional

product support and to locate your nearest dealer, please visit minnkotamotors.com.

INSTALLATION PARTS LIST

10

11

16

17

15

13

14

6

7

8

19 20 18

21

1

9

22

4

5

3

12

BB

CC

DD

AA

2

Item /

Assembly

Part # Description Qty.

1

✖

MOTOR ASSEMBLY

1

AA

2994859

BAG ASY-TERROVA/V2,RUB.BUMPERS

1

2

2325110

PAD, FOOTPEDAL

5

BB

2994917

BAG ASSY, ULTERRA MTG HARDWARE

1

3

2203430

SCREW-1/4-20 X 2.0 HHCS SS

6

4

2203431

SCREW-1/4-20 X 0.5 HHCS SS

6

5

2201725

WASHER-CLIPPED, 1/4", 1.00" OD

6

2261713

WASHER-1/4 FLAT 18-8 SS

6

7

2263103

NUT-1/4-20 NYLOCK SS

6

8

2301720

WASHER-MOUNTING - RUBBER

6

9

2203800 STRAP, HOLD DOWN

1

10 2994075 t

REMOTE ASSEMBLY, IPILOT

1

11 2994076 t

REMOTE ASSEMBLY LINK

TOUCHSCREEN

1

p

2397101 t MANUAL, QUICK REF., iPILOT 1.6 1

p

2397103 t MANUAL-QUICK REF., iPILOT 3.0 1

12 2390800 t

LANYARD, REMOTE W/ CARABINER

1

13

2373241 t CABLE, USB REMOTE CHARGER LINK

1

14

2375901 t ADAPTER, USB DC POWER LINK

1

15

2996400 t

HEADING SENSOR SEMBLY 1

16

490389-1 t CABLE, ETH (M12-M-M12-F, 30'

1

17

2211415 CABLE-EXTENSION, PD/AP 110"

1

CC

1378132 80# THRUST PROP KIT

1

DD

1378160 112# THRUST PROP KIT

1

18

2262658 PIN-DRIVE 1" X 3/16" S/S

1

19

2091701 WASHER-PROP (LARGE) MAX101

1

20

2093101 NUT-PROP,NYLOC,LG,MX101 3/8 SS

1

21

2331160 PROP-WW2 (4") w/ADP.RING

1

2341160 PROP-WW2 (4.5) w/ADP.RING

1

p

2207113 MANUAL, INSTALL GUIDE, ULTERRA

1

22

2994740 FOOT PEDAL ASSY, ULTERRA

1

p Not shown on Parts Diagram.

✖ This part is included in an assembly and cannot be ordered individually.

t Only available with models factory installed with i-Pilot or i-Pilot Link.

6 | minnkotamotors.com

INSTALLING THE ULTERRA

• #2 Phillips Screwdriver

• #3 Phillips Screwdriver

• Drill

• 9/32" Drill Bit

• A person to help with

installation

MOUNTING CONSIDERATIONS

TOOLS AND RESOURCES REQUIRED

INSTALLATION

a. Place the mount on an elevated, level surface

such as a workbench or the tailgate of a pickup.

The motor, as removed from the box, should be in

the stowed position.

b. Remove the four sideplate screws using a #3 or

#2 Phillips screwdriver. Two of these screws will

be located on each side of the mount.

It is recommended that the motor be mounted as close to the keel or centerline of

the boat as possible. Make sure the area under the mounting location is clear to drill

holes and install nuts and washers. Make sure the motor rest is positioned far enough

beyond the edge of the boat. The motor must not encounter any obstructions as it is

lowered into the water or raised into the boat when stowed and deployed. Consider

a quick release or adapter bracket with the installation of your motor. To view a list of

accessories, please visit minnkotamotors.com.

c. Remove the Right Sideplate to access the

Mounting Slots.

d. Remove the Left Sideplate to access the

Mounting Holes.

1

2

View accessories

available for your

trolling motor at

minnkotamotors.

com.

NOTE: This motor weighs approximately 70 lbs.

We recommend having a second person help with

the installation.

Deployed

Stowed

2d

Left Sideplate

Right

Sideplate

2c

Right

Sideplate

1b

Screw

1b

Left Sideplate

Screw

Installing the Ulterra

minnkotamotors.com | 7

INSTALLING THE ULTERRA

e. Under the Left Sideplate, the Extension Damper

obstructs access to the left front Mounting Hole.

f. Using a small Screw Driver, remove the two

5/16" E-clips holding the Extension Damper in

place. Once the E-clips are removed, slide the

Extension Damper oﬀ the Mount to expose the

left rear Mounting Hole. Set the two E-clips and

Extension Damper in a safe place so they are not

misplaced before they are reassembled later in

the installation.

3

g. Make sure the Power Cables from the battery

are disconnected, or that the breaker, if equipped,

is “oﬀ”.

4

5

E-clips

Extension Damper

E-clip

Mounting Hole

Power Cables

Deck of Boat

Keel

Mount

h. Place the motor on the bow of the boat. Place

the motor as close to the centerline or keel of

the boat as possible. The motor can be installed

on either the Port or Starboard side of the boat

based on personal preference. Reviewing the

mounting considerations at the beginning of the

installation section.

WARNING

Make sure the motor is mounted on a level surface and is not

connected to a power source.

WARNING

Do not deploy the motor until it is fully mounted to the boat.

Illustrations are for reference only. Deploying your motor

before it is mounted to the boat may cause injury.

3e

3f

NOTE: The Emergency Strap (Item #9) is used

for Manually Stowing the Ulterra. The Emergency

Strap is not secured during installation. Store it

on your boat in the event that you would need

to manually stow the motor. To learn how, please

refer to the "Manually Stowing the Ulterra"

section of the Owner's Manual.

8 | minnkotamotors.com

INSTALLING THE ULTERRA

6

i. Make sure the slot on the underside of the Base

Extrusion is aligned with the outermost part of

the gunwale of the boat. This will ensure that the

Shaft has a minimum clearance of 1-1/2" when

it is deployed. The lower unit when stowed and

deployed must not encounter any obstructions.

j. Check to be sure that the Mount is level. Use the

Rubber Washers (Item #8) provided to create a

level surface if necessary.

Gunwale

Slot

Base

Extrusion

7

Bow

k. It is recommended to mark at least 4 of the 6

holes in the Base Extrusion to have a minimum

of two bolts on each side that are located the

farthest apart. Ideal installation would allow for

6 bolts to be used, with a minimum of 4.

l. Make sure the area under the mounting location

is clear to drill holes and install nuts and washers.

Drill through the marked holes using a 9/32"

drill bit.

ITEM(S) NEEDED

Mounting Holes

Mounting Slots

Base Extrusion

#8 x 6

Shaft

Gunwale

1-1/2"

Minimum

WARNING

Do not deploy the motor until it is fully mounted to the boat.

Illustrations are for reference only. Deploying your motor

before it is mounted to the boat may cause injury.

minnkotamotors.com | 9

INSTALLING THE ULTERRA

m. Mount the motor to the boat using the provided

hardware. Place the installation hardware for the

side of the mount where the Power Tilt is located

ﬁrst. This is the opposite side of the mount from

where the Extension Damper was removed. The

base of the Mount where the Power Tilt is located

has Mounting Slots and the side where the

Extension Damper is located has Mounting Holes.

8

NOTE: To prevent seizing of the stainless steel

hardware, do not use high speed installation

tools. Wetting the screws or applying an anti-

seize may help prevent seizing.

NOTE: The Long Bolts, Flat Washers and

Nylock Nut are not used when installing the

Ulterra with a Quick Release Bracket.

9

9n

UTION

Use extra care to avoid pinching and damaging the sensor

wires that run along side of the Base Extrusion when installing

and tightening the motor mounting bolts.

Power Tilt

Mounting Slots

Clipped

Washer

Quick Release Bracket

Hex Head Bolt

#3 x 3 #6 x 3 #5 x 3 #7 x 3 #4 x 3

ITEM(S) NEEDED

n. If installing with a Quick Release Bracket,

install the motor with the Hex Head Bolts (Item

#4) and Clipped Washers (Item #5). Orientate

the Clipped Washers so that the ﬂat side of the

washer is towards the Base Extrusion. The Bolt

should pass through the Clipped Washer and

into a Quick Release Bracket. Leave at least 1/4"

space between the Hex Head Bolt and Clipped

Washer in order to slide the Base Extrusion under

the Clipped Washer and into place.

10 | minnkotamotors.com

INSTALLING THE ULTERRA

o. If installing directly to the boat deck, install

the motor with the Long Bolts (Item #3), Clipped

Washer (Item #5), Flat Washer (Item #6) and

Nylock Nut (Item #7). Orientate the Clipped

Washers so that the ﬂat side of the washer is

towards the Base Extrusion. The Bolt should pass

through the Clipped Washer, the Rubber Washer

and then through the Boat Deck. The Bolt should

be secured by ﬁrst adding the Flat Washer (Item

#6) to the Bolt and securing with a Nylock Nut

(Item #7). Leave at least 1/4" space between the

Hex Head Bolt and Clipped Washer and the deck

of the boat. This will leave enough space to slide

the Base Extrusion between the Clipped Washer

and Rubber Washer and into place.

NOTE: The Short Bolts are not used when

installing the Ulterra directly to the boat.

p. Slide the Base Extrusion into place under the

Bolts that were just installed.

q. If installing with a Quick Release Bracket,

the Base Extrusion should slide between the

Quick Release Bracket and the Clipped Washers.

Hold the Clipped Washers up on the Hex Head

Bolt, so the Clipped Washer will sit on top of the

Base Extrusion.

r. If installing directly to the boat deck, the

Base Extrusion should slide between the Clipped

Washer and the Rubber Washer. Hold the Clipped

Washers up on the Long Bolt, so the Clipped

Washer will sit on top of the Base Extrusion.

11q

11r

Boat Deck

Power Tilt

Base

Extrusion

Base Extrusion

Power Tilt

Quick Release Bracket

Boat Deck

10

11

10o

Long Bolts

Clipped

Washer

Clipped

Washer

Clipped

Washer

Rubber Washer

Rubber

Washer

Flat Washer

Nylock Nut

Power

Tilt

minnkotamotors.com | 11

INSTALLING THE ULTERRA

12

s. Place the hardware on the Damper side of the

mount into the Mounting Holes to secure the

Base Extrusion.

t. If installing with a Quick Release Bracket,

install the motor with the Hex Head Bolts (Item

#4) and Clipped Washers (Item #5). Orientate

the Clipped Washers so that the ﬂat side of the

washer is towards the Base Extrusion. The Bolt

should pass through the Clipped Washer, Base

Extrusion and into a Quick Release Bracket.

u. If installing directly to the boat deck, install

the motor with the Long Bolts (Item #3), Clipped

Washer (Item #5), Flat Washer (Item #6) and

Nylock Nut (Item #7). Orientate the Clipped

Washers so that the ﬂat side of the washer is

towards the Base Extrusion. The Bolt should pass

through the Clipped Washer, the Base Extrusion,

the Rubber Washer and then through the Boat

Deck. The Bolt should be secured by ﬁrst adding

the Flat Washer (Item #6) and then securing with

a Nylock Nut (Item #7).

ITEM(S) NEEDED

UTION

Use extra care to avoid pinching and damaging the sensor

wires that run along side of the Base Extrusion when installing

and tightening the motor mounting bolts.

NOTE: To prevent seizing of the stainless steel

hardware, do not use high speed installation

tools. Wetting the screws or applying an anti-

seize may help prevent seizing.

NOTE: The Long Bolts, Flat Washers and

Nylock Nut are not used when installing the

Ulterra with a Quick Release Bracket.

NOTE: The Short Bolts are not used when

installing the Ulterra directly to the boat.

12s

12t

12u

Mounting Holes

Mounting

Holes

Quick Release Bracket

Mounting Holes

Boat Deck

Hex Head Bolt

Clipped

Washer

Long Bolts

Clipped

Washer

Rubber

Washer

Flat Washer

Nylock Nut

#3 x 3 #6 x 3 #5 x 3 #7 x 3 #4 x 3

12 | minnkotamotors.com

INSTALLING THE ULTERRA

13

14

v. At this point in the installation process the

Mount should be secured to the deck of the boat,

and the Motor can now be reassembled. The

Extension Damper can be slid back in place on

the Motor. This should be done so the shaft on

the Damper is pointing inboard. Reinstall the two

5/16" E-clips.

w. Replace the Right Sideplate.

x. Replace the Left Sideplate.

y. Replace the four sideplate Screws using a #2 or

#3 Phillips Screw Driver.

14w

14x

Left Sideplate

Screw

NOTE: The pads are recommended when using

the Foot Pedal on non-carpeted surfaces.

15

Foot Pedal

Bottom

Foot Pedal

Pad Placement

ITEM(S) NEEDED

#18 x 4 #EE x 1

z. Take the Foot Pedal (Item #EE) and turn it over.

Put a Foot Pedal Pad (Item #18) in each of the

pad locations.

Right Sideplate

Screw

E-clips

Extension Damper

minnkotamotors.com | 13

ROUTING UNIVERSAL SONAR & -PILOT LINK CABLESi

Routing Universal Sonar & i-Pilot Link Cables

Your trolling motor may be pre-installed with a Universal Sonar transducer system. Universal Sonar is a 2D sonar transducer

with a temperature sensor that is integrated into the lower unit of the trolling motor. It has an operating frequency of 83/200

kHz. Connecting this transducer to a compatible ﬁsh ﬁnder* gives you a 2D sonar view of what is happening directly below your

trolling motor. The integrated design protects the transducer from underwater hazards, and prevents tangles and damage to the

transducer cables.

In certain situations, air bubbles may adhere to the surface of the Universal Sonar transducer, and aﬀect the performance. If this

happens simply wipe the surface of the transducer with your ﬁnger.

All Universal Sonar motors are equipped with an internal bonding wire, incorrect rigging will cause sonar interference and can

damage your trolling motor, electronics and other boat accessories. Please refer to the Battery & Wiring Installation and Motor

Wiring Diagram sections of this manual for correct rigging instructions.

NOTE: Universal Sonar only provides 2D sonar that operates at 83/200 kHz. It does not support imaging screens

that require higher frequencies such as 455 kHz or 800 kHz (Down Imaging, Side Imaging, etc.). Down Imaging (DI)

speciﬁc units are not compatible with Universal Sonar. See compatibility chart for a list of compatible ﬁsh ﬁnders at

minnkotamotors.com. *Requires an adapter that is sold separately. For a current list of compatible ﬁsh ﬁnders and the

correct adapter cable, please visit minnkotamotors.com.

Your trolling motor may be pre-installed with a Universal Sonar transducer system. For compatibility and more information on

Universal Sonar, please visit minnkotamotors.com. Your trolling motor may also be pre-installed with either i-Pilot or i-Pilot

Link. To learn more about the GPS capabilities available with your i-Pilot or i-Pilot Link navigation system, please refer to the

corresponding Owner's Manual by visiting minnkotamotors.com.

Both the Universal Sonar and i-Pilot Link features require cables to be connected to an output device. These connections are

present on the trolling motor below the Control Head. The i-Pilot system does not need an external wired connection. If only one

connection is present, it is because your motor is equipped with the i-Pilot system. If only a single connection is present, it is to

connect the Universal Sonar. If two cables are present, one is to connect the Universal Sonar, and the other is to connect the

i-Pilot Link connection. Please follow the Minn Kota recommendations on routing the cables to optimize mobility and maximize

functionality.

The routing will be the same regardless of the number of cables present. Use the following instructions to properly

route cables.

The Universal Sonar Cables are shielded to minimize interference. To protect this shielding the cables should not be pulled tight

against sharp angles or hard objects. If using cable ties, do not over-tighten. Any excess cable should be bundled in a loose loop

of no less than 4” in diameter.

To minimize trolling motor interference, ensure that the ﬁsh ﬁnder and trolling motor are powered by separate batteries. Please

refer to the Battery & Wiring Installation and Motor Wiring Diagram sections of this manual for correct rigging instructions.

To better identify cables present that exit the Control Head, refer to the diagrams below that detail what the Universal Sonar and

i-Pilot Link cable connectors look like.

Four Pin Connector

Universal Sonar Cable

from Control Head

i-Pilot Link Cable from

Control Head

Universal Sonar

Extension Cable

i-Pilot Link Cable

Locking Collar

Eight Pin Connector

14 | minnkotamotors.com

ROUTING UNIVERSAL SONAR & -PILOT LINK CABLES

a. Place the motor in the deployed position.

b. Locate the Universal Sonar and/or the i-Pilot Link

cable(s), at the base of the Control Head.

c. The Universal Sonar Cable and/or i-Pilot Link

cable should be fed all the way through the Coil

Cord. It/they should exit the Coil Cord at the

bottom of the Coil Cod, where it connects to the

Mount.

1

UTION

Not following the recommended wire routing for the

Universal Sonar and/or i-Pilot Link cable(s), if equipped,

may cause damage to the product and void your product

warranty. Route cables away from pinch points or other

areas that may cause them to bend in sharp angles.

Routing the cables in any way other than directed may

cause damage to the cables by being pinched or severed.

Control Head

Coil Cord

Mount

Universal

Sonar

i-Pilot Link

NOTE: After the Universal Sonar Cable and/or i-Pilot

Link Cable exits the Coil Cord, it should be routed

through an established routing system on the boat, in

an area with minimal interference. Inspect the selected

route carefully to ensure that there are no sharp

edges, obstacles, or obstructions that may damage

the cables.

i

minnkotamotors.com | 15

CONNECTING A UNIVERSAL SONAR EXTENSION CABLE

Four Pin Connector

Universal Sonar

Cable from

Control Head

NOTE: Your ﬁsh ﬁnder should be turned

oﬀ until this procedure is complete.

NOTE: If the cable length does not reach the desired

ﬁsh ﬁnder installation location, a 14.5’ extension cable

is available (MKR-US2-11) (sold separately).

a. Place the motor in the deployed position.

b. Locate the Universal Sonar, if equipped, at the

base of the Mount.

c. Locate the Universal Sonar four pin connector at

the end of Universal Sonar Extension Cable. The

connector is black with a stainless steel threaded

locking collar.

1

The Universal Sonar Cable may not be long enough to reach the ﬁsh ﬁnder. If the cable length does not reach the desired ﬁsh

ﬁnder installation location, a 14.5’ extension cable is available. Minn Kota recommends using the MKR-US2-11.

Connecting a Universal Sonar Extension Cable

2

Four Pin Connector

Universal Sonar Cable

from Control Head

Universal Sonar

Extension Cable

Locking Collar

d. Align the pins of the Universal Sonar connector

plug from the Control Head with the matching

socket end of the appropriate Universal Sonar

Extension Cable for your ﬁsh ﬁnder. Firmly

push the connector plug into the socket of the

Universal Sonar connection. Twist the locking

collar until it is snug.

e. Connect the other end of your adapter plug to

your ﬁsh ﬁnder following the manufacturer’s

instructions.

NOTE: The connectors are keyed to prevent reversed

installation.

Control Head

Coil Cord

Mount

Universal

Sonar

16 | minnkotamotors.com

INSTALLING THE PROP

1

Installing the Prop

ITEM(S) NEEDED

#18 x 1#20 x 1

#19 x 1

#21 x 1

UTION

Disconnect the motor from the battery before beginning

any prop work.

a. Take the Drive Pin (Item #18) and slide it through

the Hole in the Armature Shaft. Position the

Drive Pin horizontal by grasping the Armature

Shaft and rotating it with the Drive Pin in place.

b. Align the Propeller (Item #21) so it is also

horizontal and parallel with the Drive Pin. Slide

the Propeller onto the Armature Shaft and Drive

Pin until it is seated against the lower unit.

c. Install the Prop Washer (Item #19) and the Prop

Nut (Item #20) onto the end of the Armature

Shaft.

d. Holding the end of the Armature Shaft with a Flat

Blade Screwdriver, tighten the Prop Nut with a

9/16" Open End Wrench.

e. Tighten the Prop Nut 1/4 turn past snug to

25-35 in-lbs.

UTION

Do not over tighten as this can damage the prop.

Propeller

Prop Nut

Prop Washer

Drive Pin

Propeller

Prop Nut

Prop Washer

Drive Pin

Armature Shaft

1a

1b

1d

minnkotamotors.com | 17

STOWING AND DEPLOYING THE MOTOR WITH THE FOOT PEDAL

c. On the Foot Pedal, press the Mode Button until

the amber LED in the center of the Indicator

Panel on the Foot Pedal is illuminated. This puts

the Foot Pedal in Ulterra Mode.

d. To deploy the motor, when it is stowed, double

press the Stow/Deploy button. To stow the

motor, when it is deployed, press the Stow/

Deploy button.

1

Use the following procedure to stow and deploy the motor. Keep in mind that if your motor is stalling at a

45-degree angle when attempting to stow, this indicates that batteries are too low to fully stow the motor. If

this occurs, reengage power, deploy the motor, trim the motor to its highest setting, and turn power oﬀ until

batteries can be recharged. Once batteries are charged, attempt to stow motor again.

Stowing and Deploying the Motor with the Foot Pedal

NOTE: You can only stow and deploy your motor

while in Ulterra mode.

NOTE: To stow and deploy the Ulterra with the

i-Pilot or i-Pilot Link remote, please refer to the

corresponding product literature.

SYSTEM READY

POWER

STATUS

a. Locate the Indicator Panel at the base of

the Mount.

b. Make sure that the motor is on by checking

that the green LED next to the System Ready

Indicator is on.

2

Power Button

System Ready

Indicator

WARNING

When stowing or deploying the motor, keep ﬁngers

clear of all hinges, pivot points and all moving parts.

When stowing and deploying the motor, ensure

that it doesn’t contact the boat, trailer, or any

other obstruction.

AUTOPILOT

SPOT-LOCK

MODE

CONSTANT

AUTOPILOT

SPOT-LOCK

MODE

CONSTANT

Stow/Deploy

MODE

NOTE: The deploy sequence can be stopped at any

time pressing the stow/deploy button. The stow

sequence can be stopped at any time by pressing

either trim button or the stow/deploy button.

18 | minnkotamotors.com

DEPLOYING THE MOTOR WITH I-PILOT

Deploying the Motor with i-Pilot

a. Press the Home button.

b. Use the Menu Up and Menu Down buttons

to ﬁnd the Deploy menu at the bottom of the

display screen.

1

2

1a

2d 2e

1b

NOTE: The Deploy menu at the bottom of the

display screen can only be found when the motor

is stowed.

c. Use the Right Softkey

to select the Deploy

menu by double pressing it. Once selected the

motor will automatically deploy.

d. While the Motor is deploying, it is possible to

stop the action. Use either the Left Softkey

to select the Stow menu or the Right Softkey

to select the Pause menu.

e. If the Motor continues, it will complete the

deploy process, normal motor operation will

follow.

WARNING

As soon as the Deploy menu is selected, the motor will

automatically deploy. Be sure the motor is clear from

obstructions and has a clear path of travel. The Prop is

disabled while the motor is stowed and being deployed

to prevent accidental contact with the rotating

propeller.

Stowing the Motor with i-Pilot

a. Press the Home button.

b. Use the Menu Up and Menu Down buttons

to ﬁnd the Stow menu at the bottom of the

display screen.

1

1a 1b

NOTE: The Stow menu at the bottom of the

display screen can only be found when the motor

is deployed.

minnkotamotors.com | 19

DEPLOYING THE MOTOR WITH I-PILOT LINK

c. Use the Right Softkey to select the

Stow menu. Once selected the motor will

automatically stow.

2

2d 2e

d. While the Motor is stowing, it is possible to stop

the action. Use either the Left Softkey

to

select the Deploy menu or the Right Softkey

to select the Pause menu.

e. If the Motor continues, it will complete the Stow

process and the Prop will be disabled.

WARNING

As soon as the Stow menu is selected, the motor will

automatically stow. Be sure the motor is clear from

obstructions and has a clear path of travel. The Prop is

disabled while the motor is being stowed to prevent

accidental contact with the rotating propeller.

Deploying the Motor with i-Pilot Link

a. Press the Home button.

b. Scroll through the Content Area using either your

ﬁnger or the Screen Navigation

button to ﬁnd

the Ulterra

button.

c. Select the Ulterra button using either your

ﬁnger or by pressing the Ok

button to open the

Ulterra Menu.

1

1c 1c

NOTE: The Ulterra button can only be found

in the Content Area with the Home Control

Buttons on i-Pilot Link systems on an Ulterra

motor. Certain Home Screen Buttons may be

locked out while the motor is stowed because

those functions require the motor to be

deployed to operate.

20 | minnkotamotors.com

DEPLOYING THE MOTOR WITH I-PILOT LINK

2g

2

d. Once in the Ulterra Menu, ﬁnd the Deploy

button and select it. The Deploy

button

requires a double press to engage.

e. The Ulterra motor will deploy. While the Motor

is deploying, it is possible to pause the action. To

pause the action, ﬁnd the Pause

button and

select it.

f. To resume the Deploy action, select the Deploy

button.

g. If the Motor continues, it will complete the

deploy process and normal motor operation will

follow.

WARNING

As soon as the Deploy button is selected, the motor will

automatically deploy. Be sure the motor is clear from

obstructions and has a clear path of travel. The Prop is

disabled while the motor is stowed and being deployed

to prevent accidental contact with the rotating

propeller.

2d 2e

2f

La page charge ...

MINN KOTA PowerDrive Installation Instructions Manual

Ce manuel convient également à

MINN KOTA PowerDrive Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents