Smooth Fitness 935 Manuel utilisateur

USER’S MANUAL

935 MOTORIZED TREADMILL

USER WEIGHT LIMITATION: 400lbs(181kgs).

SERIAL NUMBER (found on frame):

2 935i TREADMILL

PRECAUTIONS

For future service or related questions:

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Precautions:

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions

and information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are

adequately informed of all warnings and precautions.

• Use the treadmill only as described in this manual.

• Place on a level surface, with 6 feet 2 X1m

of clearance behind it. Do not place the treadmill on any surface that blocks air

openings. To protect the floor or carpet from damage, place a mat under the treadmill.

• When choosing a location for the treadmill be sure that the location and position permit access to a plug.

• Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near

water.

• Do not operate the treadmill where aerosol products are used or where oxygen is being administered.

• Keep children under the age of 12 and pets away from the treadmill at all times.

• The treadmill should not be used by persons weighing more than 400LBS (181 Kgs).

•

Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the treadmill.

Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both

men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in

sandals.

• When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same

circuit.

• Always straddle the belt and allow it to start moving before stepping onto the belt.

• Always examine your treadmill before using to ensure all parts are in working order.

• Allow the belt to fully stop before dismounting.

• Never insert any object or body parts into any opening.

• Follow the safety information in regards to plugging in your treadmill.

• Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not

operate the treadmill with a damaged or frayed power cord.

• Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an

authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these

instructions will void the treadmill warranty.

• Never leave the treadmill unattended while it is running.

• Use “safety key” when operating the treadmill and make sure the “safety key” is clipped to the users clothing.

• Remove the “safety key” and store it in a safe place when the treadmill is not in use. Keep the “safety key” away from

children.

www.smoothfitness.com

3

PRECAUTIONS

Pour réparations futures ou questions connexes :

Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.

Name: ______________________________ Phone Number: ___________________ Receipt: ______________________

Précautions:

AVERTISSEMENT : Pour réduire les risques de brûlures, d’incendie, de choc électrique ou de blessures aux personnes, lire les

précautions importantes et l’information suivantes avant de se servir du tapis roulant. Il revient au propriétaire de s’assurer que tous

les utilisateurs de ce tapis ont bien été informés de tous les avertissements et précautions.

• Utiliser le tapis seulement comme il est décrit dans ce manuel.

• Le placer sur une surface plane, en laissant 2X1m d’espace libre en arrière. Ne pas placer le tapis roulant sur une surface

qui bloque les ouvertures d’air.

• Pour protéger le plancher ou un tapis de dommages, placer un petit tapis sous le tapis roulant.

• Choisir pour le tapis roulant un emplacement et une position qui permettent d’avoir accès à une prise murale.

• Garder le tapis roulant à l’intérieur, à un endroit sans humidité ni poussière. Ne pas mettre le tapis roulant dans un garage,

sur une terrasse couverte ou près de l’eau.

• Ne pas faire fonctionner le tapis roulant pendant la vaporisation de produits aérosol ou l’administration d’oxygène.

• Ne pas laisser les enfants de moins de 12 ans et les animaux s’approcher du tapis roulant.

• Le tapis roulant ne doit pas être utilisé par des personnes pesant plus de 181 kg (400lb).

• Il ne doit jamais y avoir plus d’une personne sur le tapis à la fois. Porter des vêtements d’exercice appropriés pour utiliser

le tapis roulant. Ne pas porter de vêtements lâches qui pourraient être pris dans le tapis roulant. Les vêtements de soutien

athlétiques sont recommandés tant pour les hommes que pour les femmes. Porter toujours des chaussures d’athlétisme.

Ne pas être pieds nus, ou porter seulement des chaussettes ou des sandales lors de l’utilisation du tapis roulant.

• Brancher le cordon d’alimentation dans un circuit avec mise à la terre. Aucun autre appareil ne doit être sur le même

circuit.

• Toujours enjamber le tapis et le laisser commencer à rouler avant de monter dessus.

• Toujours examiner votre tapis roulant avant de l’utiliser pour s’assurer que toutes les pièces fonctionnent correctement.

• Laisser le tapis s’arrêter complètement avant de descendre.

• Ne jamais insérer d’objets ou de parties du corps dans une ouverture.

• Suivre les directives de sécurité en ce qui concerne le branchement de votre tapis roulant.

• Garder le cordon d’alimentation éloigné des roues inclinées et ne pas faire passer le cordon d’alimentation sous votre

tapis roulant. Ne pas faire fonctionner le tapis roulant si le cordon d’alimentation est endommagé ou effiloché.

• Débrancher toujours le tapis roulant avant de le nettoyer ou de le réparer.

• Toute réparation au tapis doit être effectuée par un réparateur agréé, à moins d’autorisation ou de directives contraires du

fabricant. Le non-respect de ces instructions annulera la garantie du tapis roulant.

• Ne jamais laisser le tapis roulant sans surveillance lorsque la clé de sécurité est insérée.

• Utiliser la « clé de sécurité » pour faire fonctionner le tapis roulant et s’assurer qu’elle est accrochée aux vêtements des

utilisateurs.

• Retirer la « clé de sécurité » et la ranger dans un endroit sûr lorsque le tapis roulant n’est pas en fonction. Garder la « clé

de sécurité » hors de la portée des enfants.

4 935i TREADMILL

POWER REQUIREMENTS

Power Requirements:

IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC

SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE

PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT

THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and

noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of

treadmill damage, always use a surge protector (not included) with your treadmill.

Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a

UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an

electrical rating 120VAC, 15 amps.

This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric

current, should the treadmill malfunction. This treadmill is equipped with an electrical cord that has an equipment-grounding

conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing

below.

GFCI outlets and GFCI / AFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI / AFCI

Circuit Breakers may cause this equipment to function improperly.

www.smoothfitness.com

5

POWER REQUIREMENTS

Alimentation :

UN MAUVAIS BRANCHEMENT DU CONNECTEUR DE MISE À LA TERRE DE L’ÉQUIPEMENT POURRAIT PROVOQUER UN

CHOC ÉLECTRIQUE. EN CAS DE DOUTE, CONSULTER UN ÉLECTRICIEN OU UN RÉPARATEUR QUALIFIÉ POUR SAVOIR

SI LE PRODUIT EST CORRECTEMENT MIS À LA TERRE. NE PAS MODIFIER LA FICHE FOURNIE AVEC LE PRODUIT. SI

ELLE N’ENTRE PAS DANS LA PRISE, FAIRE INSTALLER UNE PRISE APPROPRIÉE PAR UN ÉLECTRICIEN

PROFESSIONNEL.

Ce tapis roulant pourrait être gravement endommagé en cas de changement soudain de tension dans votre alimentation électrique.

Les conditions météorologiques ou la mise sous tension ou hors tension d’autres appareils électriques peuvent provoquer des

pointes de tension, des surtensions ou un brouillage. Pour réduire la possibilité que le tapis soit endommagé, toujours utiliser un

limiteur de surtension (non inclus) avec votre tapis roulant.

Il est possible d’acheter des limiteurs de surtension dans la plupart des quincailleries. Le fabricant recommande un limiteur de

surtension UL 1449 à prise unique comme suppresseur de tension transitoire (TVSS) ayant un taux de suppression de tension de

400 V ou moins et une tension électrique de 110 V C.A., 15 A.

Ce tapis roulant doit être mis à la terre pour réduire le risque de choc électrique. La mise à la terre fournit une voie de moindre

résistance au courant électrique en cas de mauvais fonctionnement du tapis roulant. Ce tapis roulant est équipé d’un cordon

électrique avec un conducteur de mise à la terre et une fiche de mise à la terre. Brancher toujours le cordon électrique dans un

limiteur de surtension et brancher le limiteur de surtension dans une prise appropriée, correctement installée et mise à la terre

conformément à tous les codes locaux et ordonnances.

Ce produit doit être utilisé avec un circuit nominal de 110 volts et à une fiche de mise à la terre qui ressemble à celle illustrée ci-

dessous.

Les prises avec disjoncteur de fuite de terre et les disjoncteurs de fuite de terre ne sont PAS recommandés pour ce produit. Les

prises avec disjoncteur de fuite de terre et les disjoncteurs de fuite de terre pourraient provoquer un mauvais fonctionnement de cet

équipement.

6 935i TREADMILL

BEFORE YOU BEGIN

Open the boxes:

Open the boxes of your new equipment. Inventory all parts included in the boxes, and Supplied Hardware lists

on pages 7 for a full count of the parts included. If you are missing any parts or have any questions contact us

directly at 888-800-1167

Gather your tools:

Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit

properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.

Clear your work area:

Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is

free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a

comfortable amount of free area around the unit for unobstructed operation.

Invite a friend:

Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another

person when assembling this product.

User Weight Limitation:

Please note that there is a weight limitation for this product. If you weigh more than 350LBS (Approx. 160 Kgs). It is

not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown

here. This product is not intended to support users whose weight exceeds this limit.

Care and maintenance:

The safety level can be maintained only if it is examined for damage and wear.

Replace any defective components immediately and stop all use of the equipment until repaired.

Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails.

Dismount from the equipment only after all parts have stopped.

Always check the wear and tear components like pulley, belts, etc.…To prevent injury.

There is an emergency stop, in the form of a SAFETY KEY, to prevent injury; you can stop the treadmill immediately

by actuating the emergency stop for emergency dismount.

www.smoothfitness.com

7

SUPPLIED COMPONENTS / SUPPLIED HARDWARE

This list identifies the major components you will use to assemble this product.

No. Description Qty.

A1

Treadmill Base

1

A2

Console Assembly

1

935i -301

Right Upright

1

935i -302

Left Upright

1

935i -306

Right Handle Bar

1

935i -307

Left Handle Bar

1

Hardware Kit

935i -303

M8x15mm Bolt

20

935i -304

M8 Curve Washer

4

935i -305

M8 Washer

16

A

5mmx76 Allen Key

1

B

5mmx114 Allen Key

1

C

6mm Allen Key

D

Silicone Lubricant

1

935i -232

Safety Key

1

Millimeters

A1

302 301

A2

307 306

305

304

303

B

A

D

232

C

8 935i TREADMILL

COMPLETE PARTS LIST

Item No. Description Qty.

935i -100

935i -101

Lift arm

1

935i -102

Rear wheel 2

935i -103

Bolt M10*70mm 2

935i -104

Washer M10

4

935i -105

Wheel axle center 2

935i -106

Nut M10 4

935i -107

Adjustment pad 2

935i -108

Bolt M8*20mm 2

935i -109

Running deck frame 1

935i -110

Bushing 2

935i -111

Bolt 1/2”*82mm

2

935i -112

Washer M13 4

935i -113

Nut 1/2” 2

935i -114

Wire set plate 1

935i -115

Electric socket 1

935i -116

On-off switch 1

935i -117

Power breaker 1

935i -118

Bolt M3*8mm 2

935i -119

Bolt M4*10mm 2

935i -120

Incline motor 1

935i -121

Bolt M10*45mm 1

935i -122

Bolt M10*60mm 1

935i -123

Bolt M12*80mm 2

935i -124

DC motor

1

935i -125

Bolt M10*35mm 4

935i -126

S Washer M10 4

935i -127

Washer M10 4

935i -128

Bolt M8*90mm 1

935i -129

Washer M8 1

935i -130

Nut M8 2

935i -131

Motor control board

1

935i -132

Fixing bracket, motor control 1

935i -133

Power cord 1

935i -134

Lower console wire

1

935i -135

Bolt M4*10mm 15

935i -136

Bolt M4*10mm 4

935i -137

Sensor 1

935i -138

Bolt M3*8mm 2

935i -139

Rubber cushion-1 6

935i -140

bolt M8*15mm 6

www.smoothfitness.com

9

COMPLETE PARTS LIST

Item No. Description Qty.

935i -

141

Tooth plate

2

935i -142

Rubber cushion-2

2

935i -143

Drive belt

1

935i -144

Front roller

1

935i -145

Bolt M8*35mm

2

935i -

146

Rear roller

1

935i -

147

S Washer M8

4

935i -

148

Bolt M8*70mm

2

935i -149

Running deck

1

935i -150

Running belt

1

935i -151

Bolt M8*35mm

2

935i -152

Bolt M8*40mm

2

935i -

153

Right side rail

1

935i -

154

Left side rail

1

935i -155

Bolt M5*10mm

10

935i -156

Side rail fixer

10

935i -157

Upper side rail

2

935i -158

Fixing bracket, right roller cover

1

935i -

159

Fixing bracket, left roller cover

1

935i -

160

Bolt M4*10mm

4

935i -

161

Right roller cover

1

935i -162

Left roller cover

1

935i -163

Fixing bracket, protective cover

2

935i -164

Tooth plate

6

935i -165

Bolt M4*15mm

6

935i -

166

Upper motor cover

1

935i -

167

Adaptor

1

10 935i TREADMILL

Item No. Description Qty.

935i -200

935i -201

Console frame

1

935i -202

Hand pulse upper cover

2

935i -203 Hand pulse lower cover 2

935i -204

Bolt M3*20mm

4

935i -205

Hand pulse plate

4

935i -206 Upper console cover 1

935i -207

Console housing

1

935i -208

Panel, console

1

935i -209

Bolt M3*6mm

14

935i -210

Safety key base

1

935i -211

Fan

1

935i -212

Bolt M3*30mm

4

935i -213

Speaker

2

935i -214

Bolt M4*12mm

17

935i -215

IHP

1

935i -216 Bolt M2.6*8mm 2

935i -217

USB charger

1

935i -218

Bolt M2*6mm

6

935i -219

Tablet Shelf

1

935i -220

Audio jack

1

935i -221

Bolt M2*5mm

2

935i -222

Receiver

1

935i -223

Handle button wire

6

935i -224

Washer M4

4

935i -225

Screw location fixer

2

935i -226 Lower console cover 1

935i -227

Bolt M4*15mm

6

935i -228

Bolt M4*10mm

2

935i -229

Operational button

1

935i -230

Hand pulse wire

1

935i -231

Console wire

1

935i -232

Safety key

1

935i -233 Software update cap

1

935i -234

Right handle button cover

1

935i -235

Left handle button cover

1

935i -236 Handle button sticker 2

935i -237

Spring

2

935i -238

M4 washer

2

935i -239

Bolt M3*10mm

2

935i -240

Tablet left support

1

935i -241

Table right support

1

935i -242

Adaptor wire

1

www.smoothfitness.com

11

COMPLETE PARTS LIST

Item No. Description Qty.

935i -300

935i -301 Right upright 1

935i -302 Left upright 1

935i -303 Bolt M8*15mm 20

935i -304 M8 curve washer 4

935i -305 M8 washer 16

935i -306 Right handle bar 1

935i -307 Left handle bar 1

12 935i TREADMILL

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED

www.smoothfitness.com

13

PARTS DIAGRAM

MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.

14 935i TREADMILL

PARTS DIAGRAM

A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY.

www.smoothfitness.com

15

ASSEMBLY – PLEASE READ ALL STEPS BEFORE BEGINNING YOUR WORK.

STEP 1:

1). Remove the motor cover(166) screws.

166

Screw location

16 935i TREADMILL

ASSEMBLY

STEP 2: Attach the Console Mast to the Base Frame.

NOTE: Make sure all wires are recessed into the frame. DO NOT trap or

pinch the wires. DO NOT tighten any bolts until STEP4.

Before attaching the Right

upright (301) first wrap the fish wire (preinstalled from

the factory in the right upright) to the computer data wire located on the base

frame.fish wire in the upright. This will allow you to pull the data cable up through

the upright during installation.

1). Attach Left and Right Uprights into base frame, and secure using the 8 x

M8x15mm Bolt (303) with 8 x M8 Washer (305).

303

X8

305 X8

Caution Pinch point! Do not pinch wires between frame.

303

305

Green plastic wrap

Clear plastic wrap

Fish wire

Computer wire

location

Feed the computer

wire through the

upright tube

Do not tighten bolts until step 3

www.smoothfitness.com

17

ASSEMBLY

STEP 3:

1). Place the motor cover(166) back on tot the treadmill base.

2). Do not install the screws until after step four has been completed.

166

18 935i TREADMILL

ASSEMBLY

STEP 4: Attach the Handle Bars

1). Connect handlebar button wire (223) to the console set handlebar button wire.

2). Attach the right and left handle bar and secure using the 4 x M8x15mm bolt

(303) with M8 Washer (305).

Assembly is now complete.

303

X4

305 X4

Tighten all bolts and fasteners now

223

303

305

223

Speed

Incline

www.smoothfitness.com

19

ASSEMBLY

STEP 5: Attach the Console to the Left and Right Uprights

Make sure all wires are recessed into the frame. DO NOT trap or

pinch the wires.

1). Connect the Upper Console Wires from the console set to the Lower Console

Wires in the right upright, each connector are different sizes so each connector

will only connect to its proper match. Place the excess wire and the connectors

into right upright.

2). Place the entire console set onto the uprights, and secure the left side using

4 x M8x15mm Bolt (303) with 2 x M8 Washer (305) and 2 x M8 Curve Washer

(304).

3). Repeat the above process for the Right side.

4). Fully tighten all bolts from steps 2, 3 and 4.

303

X8

305 X4

304 X4

Tighten all bolts and fasteners now

206

134

303

305

304

303

242

Caution pinch point

20 935i TREADMILL

ASSEMBLY

STEP 6:

1). Attach the power cord (133) to the front of the treadmill base.

133

La page charge ...

Smooth Fitness 935 Manuel utilisateur

Smooth Fitness 935 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents