Hobart CLeN Blower Dryer Manuel utilisateur

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com

E

F41108 (March 2019)

CLeN-SERIES DISHWASHERS

BLOWER-DRYER

LAVE-VAISSELLE DE LA GAMME CLEN

TUNNEL DE SÉCHAGE

LAVAVAJILLAS SERIE-CLEN

SECADOR DE AIRE

ELECTRIC (CLeN SERIES) ML-138211

ÉLECTRIQUE (GAMME CLeN) ML-138212

SISTEMA ELÉCTRICO ML-138213

(SERIE CLeN) ML-138214

STEAM (CLeN SERIES) ML-138226

VAPEUR (GAMME CLeN) ML-138227

SISTEMA A VAPOR ML-138228

(SERIE CLeN) ML-138229

– 2 –

TABLE OF CONTENTS

GENERAL ....................................................................3

INSTALLATION ................................................................3

Unpacking .................................................................3

Installation Codes ...........................................................3

Drill Holes .................................................................4

Mount Blower-Dryer to Dishwasher ..............................................6

Install Template/Stiffener ......................................................7

Mount Adjustable Legs .......................................................7

Adjust Blower-Dryer Feet for Firm Mounting .......................................7

  AdjustAirDeector ..........................................................7

Install Connecting Rods .......................................................7

Track Adjustment ............................................................8

Dish Table Assembly .........................................................8

Mount Blower Motor ..........................................................9

Blower Motor Connections ................................................10

Electrical Connections .......................................................10

Control Connections .....................................................10

Power Connections .....................................................11

Blower Motor Rotation ...................................................12

Steam Connection (When Blower-Dryer is Equipped with Steam Heat) .................12

Condensate Return Piping ................................................14

Panel Assembly ............................................................16

Drain Connection ...........................................................16

Exhaust Connection .........................................................17

    DeectorPan ..........................................................18

Adjusting the Vents on the Blower-Dryer and Dishwasher ........................18

OPERATION .................................................................19

CLEANING ..................................................................19

  RemovingtheDeectorTray ..................................................19

Dos and Don'ts for Your New Hobart Blower-Dryer .................................19

– 3 –

Installation, Operation and Care Of

CLeN-SERIES BLOWER-DRYER

SAVE THESE INSTRUCTIONS

GENERAL

The CLeN-series Blower-Dryer unit is designed to assist the drying of dishware by

drawing room air through a heated plenum into the unloading end of the dishwasher.

The unit is powered by a 2 HP electric motor and is available with three-phase

electric service only.

A condensation tight, forced exhaust system to the outside is necessary for removal

of humid drying air. This exhaust system is to be supplied by the customer. Refer

to Exhaust Connections for recommended exhaust requirements.

INSTALLATION

UNPACKING

Immediately after unpacking the blower-dryer, check for possible shipping damage.

If the machine is found to be damaged, save the packaging material and contact

the carrier within 5 days of delivery.

Priortoinstallation,verifythattheelectricalserviceagreeswiththespecications

on the machine data plate, which is located on the rear of the unit.

After unpacking the blower-dryer, remove the items that were shipped loose (hardware,

blower motor, legs) from inside the unit. Remove shipping braces and discard.

INSTALLATION CODES

Installation must be in accordance with state and local codes, or in the absence

of local codes, with the National Electrical Code ANSI / NFPA 70 (latest edition).

In Canada, the installation standard is: CSA C22.2 No. 1 (latest edition).

– 4 –

Fig. 1

DRILL HOLES

REMOVE UPPER TRIM COVER (FIG. 1) FROM UNLOAD END OF MACHINE

AND DISCARD. Position the hole template/stiffener (Fig. 2) over the existing bolt

heads on the unload end of the dishwasher (Fig. 1) per directions on template.

Mark hole locations and drill necessary holes per template. Hole diameters shown

in Fig. 2. (Save template for use in later step.)

HOLE

TEMPLATE / STIFFENER

REMOVE UPPER TRIM

COVER AND DISCARD

– 5 –

Fig. 2

CENTER PUNCH FOR 5/16" HOLE DIA, 7 PLC

CENTER PUNCH FOR 1-1/4" HOLE DIA, 2 PLC

CENTER PUNCH FOR 5/16" HOLE DIA, 6 PLC

HOLE TEMPLATE STIFFENER

CLeR BLOWER - DRYER TEMPLATE

– 6 –

5/16

MOUNTING

STUDS

ADJUSTABLE LEGS

5" FOAM

TAPE

1 " FOAM

TAPE

1/4-20 x (12)

MOUNTING

HOLES

Fig. 3

MOUNT BLOWER-DRYER TO DISHWASHER

NOTE: Thedishwashermustbeinitsnalposition,adjustedforproperheightand

properly leveled before blower-dryer can be mounted.

To mount the blower-dryer, apply the 11⁄2" foam sealant tape (supplied) along the

edges of the dishwasher to prevent leakage (Fig. 3). Also apply the 5” foam sealant

tape (supplied) below the tank lip on the dishwasher (Fig. 3). Position the blower-

dryer against the dishwasher and assemble using the ¼-20 bolts and nuts provided

(Fig. 3). Do not tighten at this time.

– 7 –

INSTALL TEMPLATE/STIFFENER

Remove knockouts from template/stiffener. Align the holes and attach the template/

stiffener to inside bottom of blower-dryer (Fig. 4) with 1/4-20 bolts and nuts provided.

Assemble remaining bolts and nuts through chamber. Tighten all bolts and nuts.

Fig. 4

MOUNT ADJUSTABLE LEGS

Mount the adjustable legs (Fig. 3) to the last set of studs in the base of the blower-

dryer using the 5/16" nuts and lock washers already attached.

ADJUST BLOWER-DRYER FEET FOR FIRM MOUNTING

Turntheadjustablefeetinwardoroutward,asnecessary,untilblower-dryerisrmly

mounted.

ADJUST AIR DEFLECTOR

Raisetheairdeectortightagainstthechamberandsecureinplacebytightening

the 5/16" bolt. See Fig. 5.

INSTALL CONNECTING RODS

Preassemble (1) elastic nut on each end of both rods, approximately 1.00" onto

the threads (Fig. 5). Route the connecting rods through the tank end. Assemble

the rods through the cross members of both cradles and add the second elastic

nut. Do not completely tighten the elastic nuts. A small gap of 0.15"- 0.020"

will allow better cradle alignment. Assure spacing between the last dog on the

parentmachineandtherstdogontheblowerdryerisequaldistanceinthefront

and rear of conveyor.

ASSEMBLE

TEMPLA

TE/STIFFENER

TO INSIDE LOAD END

OF BLOWER-DRYER

(SEE FIG. 2)

RACK

GUIDE

– 8 –

Fig. 5

CONNECTING RODS

ASSEMBLE ELASTIC STOP NUTS AT END

OF RODS FOR CORRECT ADJUSTMENT.

DO NOT OVERTIGHTEN NUTS.

THIS MAY CAUSE CONVEYOR TO BIND

0.15 - 0.020" GAP IS PREFERRED.

(4 PLACES)

TRACK ROD

APPROX. 1"

TANK END

AIR DEFLECT

OR

CONVEYOR

CROSS

MEMBERS

Fig. 6

TRACK ADJUSTMENT

Place a rack on the track in the center of the Blower-Dryer unit. Verify that there

is less than 0.25" total gap between the rack and the track. Adjust track rod as

needed (Fig. 5).

DISH TABLE ASSEMBLY

Dishtablesshouldbettedintotheblower-dryer(Figs.6,7&8).Usesiliconesealant

between table and lip of tank to prevent leakage. Rack track height should be from

1/4 to 5/16" (Fig. 7) above the tank lip. Dish tables should be sloped so that any water

carried from the dishwasher will drain back into the machine.

NOTE: Theblower-dryermustbeinitsnalposition,adjustedforproperheight

and properly leveled before table assembly and plumbing connections are made.

– 9 –

Fig. 7 Fig. 8

MOUNT BLOWER MOTOR

Take care when installing the blower motor to avoid damaging wiring

and electrical components.

Remove front and rear panels as necessary. The top and side panel unit can be

loosened on the exit side to ease installation. However, do not remove the top and

side panel unit. Take care to avoid damaging the wiring and electrical components

mounted on the side panel.

NOTE: Remove shipping brackets from sides of blower prior to installing.

Apply 1" foam sealant tape (supplied) along the edges of the blower motor to prevent

leakage. Carefully position the blower motor and the protective mylar cover (Fig. 10)

over the opening in the blower-dryer chamber top and bolt in place using 1/4-20

hardware provided.

Fig. 9

3-PHASE MOTOR

CONNECTIONS

GROUND

CONNECTION

LEVER TYPE WIRE

CONNECTORS

ELECTRONIC

OVERLOAD RELAY

– 10 –

PROTECTIVE COVER

BLOWER HARDWARE

Fig. 10

Blower Motor Connections

Carefully route the blower motor cable through the p-clip, located at the center front

of the component baseplate, to the electronic overload relay. Connect the three-

phase wiring and ground pigtail leads from the overload relay to the blower motor

cable connections using the wire connectors. Refer to the blower motor connection

chart located on the blower motor for additional information (208/480 VAC only).

Make certain the blower motor cable and connections are securely routed

away from the motor fan blades to avoid damage to the connections.

ELECTRICAL CONNECTIONS

Beforemakingelectricalconnections,checkthemachinespecicationstoensure

that they agree with those of your electrical service.

Electrical and grounding connections must comply with the

applicable portions of the National Electrical Code, NFPA 70 (latest edition)

and / or other local electrical codes.

Disconnect the electrical power to the dishwasher and follow

lockout / tagout procedures. There may be multiple circuits. Be sure all

circuits are disconnected.

Control Connections

Carefully route the control cable to the control box on top of the dishwasher. Insert

the cable into the back of the control box through the strain relief (provided) and

collect extra cable inside control box. Use wire ties (provided) to secure cable

between the blower-dryer and dishwasher control box.

Make certain the control cable is securely routed along the top of the

dishwasher unit to avoid damage.

Connect the three control cable leads to the same-named terminal block connections

as shown in Fig. 11. Refer to the electrical diagram located inside the control box

cover for additional information.

– 11 –

Power Connections

Remove two screws securing the component baseplate and slide the baseplate

forwardtogainaccesstoeldwiringterminalblock.Routetheeldwiringleads

through hole in the side of the blower-dryer unit using appropriate conduit and

ttings.Allowextralengthinleadsforproperconnections.

Connect the leads to the terminal block located at the back of the blower-dryer unit.

Connect the ground wire to the ground terminal located beside the main terminal

block. Refer to the table below for proper connection information. Slide component

baseplate back in position and secure with two bolts.

BRANCH CIRCUIT SIZE AND PROTECTION

Electric Steam

Electrical

Specs.

Rated

Amps

Min. Supply

Circuit

Conductor

Ampacity

Max.

Protective

Device Amps

Electrical

Specs.

Rated

Amps

Min. Supply

Circuit

Conductor

Ampacity

Max.

Protective

Device Amps

208/60/3 34.2 45 45 208/60/3 4.5 15 15

240/60/3 30.7 40 40 240/60/3 4.5 15 15

380/60/3 17.8 25 25 380/60/3 2.6 15 15

480/60/3 15.7 20 20 480/60/3 2.6 15 15

600/60/3 12.6 20 20 600/60/3 2.1 15 15

200/50/3 33.0 45 45 200-240/50/3 4.5 15 15

380-415/50/3 17.8 25 25 380-415/50/3 2.6 15 15

Fig. 11

– 12 –

Blower Motor Rotation

Before placing the blower-dryer into service, check to verify that the

blower motor rotates in the correct direction (arrow in blower housing indicates

correct rotation). Incorrect rotation will result in unacceptable performance.

To check the blower motor's rotation:

Turn the power disconnect switch ON and momentarily activate the blower-dryer.

The main dishwasher must be operating during this procedure.

Be careful not to touch any uninsulated electrical parts that are exposed. If the

blower motor does not rotate in the proper direction, disconnect the electrical power

supply to the machine.

Disconnect the electrical power to the machine and follow

lockout / tagout procedures. There may be multiple circuits. Be sure all

circuits are disconnected.

Reverse any two of the blower motor cable leads at the overload relay using the

lever-type wire connectors. Reconnect the electrical power supply to the machine.

Re-check the blower motor's rotation.

STEAM CONNECTION (When Blower-Dryer is Equipped with Steam Heat)

Steam supply pressure must be between 10 to 25 psig differential

pressureandprovide55poundsperhour.Ifowingpressureexceeds25psig,a

pressure regulator (customer supplied) must be installed in the supply line. Steam

owiscontrolledbyasolenoidvalve.Twoconnectionsarerequired,oneforthe

steam supply and one for the condensate return.

The example shown depicts Right to Left direction. Left to Right will have plumbing

mirrored.

To install the steam connections:

With rear panel removed, install the elbow (shipped loose) to steam inlet line on

the blower dryer (pipe sealant required).

STEAM INLET LINE

Fig. 12

– 13 –

Locate inlet piping assembly 814498 and separate at union. Connect to the elbow

as shown in Figure 13 (pipe sealant required).

Partially install support bracket to the chamber with bolt and nut as shown below.

Install remaining portion of inlet piping assembly as shown in Figure 15.

INLET PIPING ASSEMBLY (814498)

Fig. 13

SUPPORT BRACKET

Fig. 14

INLET PIPING ASSEMBLY

Fig. 15

– 14 –

Bring support bracket into position to support the inlet piping and install 2nd bolt

on chamber.

Disconnect the electrical power to the dishwasher and follow

lockout / tagout procedures. There may be multiple circuits. Be sure all

circuits are disconnected.

Remove the cover on the steam solenoid valve enclosure and remove knock-out

closesttowherethecordwillberouted.Installthestrain-reliefttinginthevalve

enclosure and connect the lead wires to the appropriate terminals. Install the valve

cover.

Condensate Return Piping

Install the top half of the support bracket to the bottom of the blower dryer as shown

in Figure 17.

2nd SUPPORT BRACKET BOLT

Fig. 16

SUPPORT BRACKET

Fig. 17

– 15 –

Locate condensate return piping assembly (814499) and break at the union. Install

the elbow on the outlet of the blower dryer heat exchanger as shown below.

Connect the remaining piping to the union as shown in Figure 19.

Install the steam trap and remaining piece of lower support bracket as shown below.

CONDENSATE RETURN

PIPING ASSEMBLY (814499)

Fig. 18

REMAINING PIPE

STEAM TRAP

LOWER BRACKET

Fig. 19

Fig. 20 Fig. 21

– 16 –

PANEL ASSEMBLY

Position front and rear panels and bolt in place with 1/4-20 truss head bolts provided.

DRAIN CONNECTION

Plumbing connections must comply with applicable sanitary,

safety and plumbing codes.

Plumbing for drain is not supplied.

Connect the 1" drain connection under the blower-dryer to a suitable drain

(Fig. 23). The drain for the blower-dryer requires only one connection to the drain. On

CLeN models only, the drain can be connected to the end of the common drain pipe

(Fig.24)forthedishwasherunitoritcanbeindependentlyconnectedtotheoor

drain. To connect to the dishwasher unit, remove the pipe plug from the common

drainpipeandconnecttheblower-dryerdrainusingappropriatettings(notsupplied).

DRAIN CONNECTION

AT EITHER END

Fig. 22

Fig. 24

Fig. 23

REAR

PANEL

FRONT

PANEL

– 17 –

EXHAUST CONNECTION

Moist air escapes from each end of the conveyor type dishwasher. The recommended

exhaust requirement is 200 CFM at the entrance end of the dishwasher and

400CFMatthedischargeend.Sufcientmake-upairmustbeprovidedsothe

exhaustowresultsinapositivebuildingpressureintheroominwhichtheunit

is located (more outside air than exhaust air). Hoods are provided with 4" x 16"

vent connectors with vent dampers which allow adjustment during installation.

Typical construction is for 'Pant-Leg' hood connections to the 4" x 16" vent connectors

(Fig.25).Ventstacksmustbewatertightandtinsidetheventconnectoropenings.

NOTE: Canopy hood installation cannot be used with blower dryer.

Fig. 25

4" X 16"

VENT

CONNECTOR

ENTRANCE

VENT STACK

DAMPER

EXIT

VENT STACK

DAMPER

ADJUST INTERNAL

VENT TO 60˚ ANGLE

DEFLECTOR PAN

PANT-LEG DUCT

– 18 –

Deector Pan

Assembledeectorpanoverdrainconectionnuts.Panisremovableforcleaning.

Adjusting the Vents on the Blower-Dryer and Dishwasher

To maintain good wash tank temperature, it is critical to adjust the vents to reduce

airowmovementcausedbythedryerfan.Therststepistoadjustdishwasher

vent system per Exhaust Spec. To help maintain tank heat, adjust the entrance and

exit dampers so the draw stops vapor from escaping into room. Excess draw can

pull tank heat from the entrance or exit of machine. Next, set the blower dryer vent

angle (located at the exit end of the blower dryer). Without removing any panels,

the damper can be adjusted by reaching into the chamber and rotating damper.

Adjust the damper to approximately 60 degrees. Next, let the dishwasher reach

mimimum temperature requirement, then turn the dishwasher ON and observe

both the entrance and discharge of the dishwasher. The curtains should be hanging

nearly straight down.

If the discharge curtain is moving excessively as pictured above, adjust the discharge

vent enough to remove steam and adjust vent on the blower dryer (air to blower

dryer) reducing the opening (angle) to approximately 45°.

BLOWER-DRYER VENT

BAFFLE

Fig. 27

Fig. 28

EXCESSIVE MOVEMENT

OF CURTAIN

ENSURE DEFLECTOR AND

BLOWER DR

YER ENTRANCE

BAFFLE ARE INSTALLED

Fig. 26

– 19 –

OPERATION

The blower-dryer comes on anytime the pumps are ON. The blower-dryer remains

ON for approximately 15 seconds after the pumps have been turned OFF by

theauto-timerorthetablelimitswitch.If15secondsisinsufcient,timecanbe

increased to a maximum of 10 minutes. Contact Hobart Service for adjustment of

timer setting. The blower-dryer turns OFF immediately when the main machine

power switch is turned OFF.

If the Over Temperature light is ON, there is a failure in the

Blower Dryer. Contact Hobart Service immediately.

CLEANING

The machine must be thoroughly cleaned at the end of each working shift, or at

least twice a day. Use only products formulated to be safe on stainless steel. Use

a damp cloth and mild soapy water.

Never use steel wool to clean warewasher surfaces. Use only products

formulated to be safe on stainless steel.

Removing the Deector Tray

Thedeectortraycanberemovedforcleaningandmaintenance.

DOs and DON'Ts for your New Hobart Blower-Dryer

DO pre-scrap dishes thoroughly.

DO, at the end of the day, thoroughly clean the machine, rinse and dry.

DO use only products formulated to be safe on stainless steel.

DO NOT allow food soil to accumulate on the tank bottom.

DO NOT use steel wool to clean ware or warewasher surfaces.

DO NOT allow foreign objects to enter the unit, especially metallic contaminants.

NOTE: Failure to follow use, care and maintenance instructions may void your

Hobart warewasher warranty.

– 20 –

F41108 (March 2019) PRINTED IN U.S.A.

La page charge ...

Hobart CLeN Blower Dryer Manuel utilisateur

Hobart CLeN Blower Dryer Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents