Poulan Pro 96092002200 Manuel utilisateur

Marque: Poulan Pro

Modèle: 96092002200

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

433107

OPERATOR'S MANUAL

MODEL:

PRRT900

REAR TINE TILLER

ALWAYS WEAR EYE PROTECTION DURING OPERATION

Visit our website: www.poulan-pro.com

WARNING:

Read this Man u al and follow all Warnings

and Safety Instructions. Fail ure to do so

can re sult in serious in ju ry.

IMPORTANT MANUAL Do Not Throw Away

12.21.09 SR

Printed in the U.S.A.

• Keep children and pets away.

• Do not overload the machine capacity by attempting

to till too deep at too fast a rate.

• Never operate the machine at high speeds on slippery

surfaces. Look behind and use care when backing.

• Never allow bystanders near the unit.

• Use only attachments and accessories approved by

the manufacturer of the tiller.

• Never operate the tiller without good visibility or light.

• Be careful when tilling in hard ground. The tines may

catch in the ground and propel the tiller forward. If this

occurs, let go of the handlebars and do not restrain the

machine.

MAINTENANCE AND STORAGE

• Keep machine, attachments, and accessories in safe

work ing condition.

• Check shear pins, engine mounting bolts, and other

bolts at frequent intervals for proper tightness to be

sure the equip ment is in safe working condition.

• Never store the machine with fuel in the fuel tank inside

a building where ignition sources are present, such

as hot water and space heaters, clothes dryers, and

the like. Allow the engine to cool before storing in any

enclosure.

• Always refer to the operator’s guide instructions for

im por tant details if the tiller is to be stored for an ex-

tended period.

- IMPORTANT -

CAUTIONS, IMPORTANTS, AND NOTES ARE A MEANS OF

ATTRACTING ATTENTION TO IMPORTANT OR CRIT I CAL

IN FOR MA TION IN THIS MANUAL.

IMPORTANT: USED TO ALERT YOU THAT THERE IS A

POS SI BIL I TY OF DAM AG ING THIS EQUIP MENT.

NOTE: Gives essential information that will aid you to bet-

ter understand, incorporate, or execute a particular set of

instructions.

Look for this symbol to point out im-

por tant safety precautions. It means

CAUTION!!! BE COME ALERT!!! YOUR

SAFE TY IS INVOLVED.

CAUTION: Always disconnect spark

plug wire and place wire where it can-

not contact spark plug in order to pre-

vent ac ci den tal starting when setting

up, trans port ing, adjusting or making

re pairs.

SAFETY RULES

Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers

TRAINING

• Read the Owner’s Manual care ful ly. Be thor ough ly

fa mil iar with the controls and the proper use of the

equip ment. Know how to stop the unit and disengage

the controls quickly.

• Never allow children to operate the equipment. Never

allow adults to op er ate the equipment without proper

instruction.

• Keep the area of operation clear of all persons, par-

tic u lar ly small children, and pets.

PREPARATION

• Thoroughly inspect the area where the equipment is

to be used and remove all foreign objects.

• Disengage all clutches and shift into neutral before

starting the engine (mo tor).

• Do not operate the equipment with out wearing ad e -

quate outer gar ments. Wear footwear that will im prove

footing on slippery surfaces.

• Handle fuel with care; it is highly flammable.

• Use an approved fuel container.

• Never add fuel to a running engine or hot engine.

• Fill fuel tank outdoors with extreme care. Never fill fuel

tank indoors.

• Replace gasoline cap securely and clean up spilled

fuel before restarting.

• Use extension cords and receptacles as specified by

the manufacturer for all units with electric drive motors

or electric starting motors.

• Never attempt to make any adjustments while the

engine (motor) is running (except where specifically

rec om mend ed by manufacturer).

OPERATION

• Do not put hands or feet near or under rotating parts.

• Exercise extreme caution when op er at ing on or cross-

ing gravel drives, walks, or roads. Stay alert for hidden

hazards or traffic. Do not carry pas sen gers.

• After striking a foreign object, stop the engine (motor),

remove the wire from the spark plug, thoroughly in spect

the tiller for any damage, and repair the damage before

restarting and op er at ing the tiller.

• Exercise caution to avoid slipping or falling.

• If the unit should start to vibrate ab nor mal ly, stop the

engine (motor) and check immediately for the cause.

Vi bra tion is generally a warning of trouble.

• Stop the engine (motor) when leaving the operating

position.

• Take all possible precautions when leav ing the ma chine

unattended. Disengage the tines, shift into neutral, and

stop the engine.

• Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent accidental starting. Disconnect

the cord on electric motors.

• Do not run the engine indoors; exhaust fumes are

dangerous.

• Never operate the tiller without proper guards, plates,

or other safety protective devices in place.

WARNING

The engine exhaust from this product con-

tains chem i cals known to the State of Cal i -

for nia to cause cancer, birth defects, or other

reproductive harm.

CONGRATULATIONS on your purchase of a new tiller. It

has been designed, en gi neered and manu fac tured to give

you the best pos sible de penda bil ity and per form ance.

Should you experience any prob lems you can not easily

remedy, please contact your nearest authorized service

center. We have com pe tent, well-trained tech ni cians and

the proper tools to service or repair this unit.

Please read and retain this manual. The in struc tions will

enable you to assemble and main tain your tiller prop erly.

Always observe the “SAFETY RULES”.

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.

• Follow a regular schedule in maintaining, caring for

and using your tiller.

• Follow instructions under “Maintenance” and “Stor age”

sections of this Owner’s Manual.

IMPORTANT: THIS UNIT IS EQUIPPED WITH AN INTERNAL

COMBUSTION ENGINE AND SHOULD NOT BE USED ON

OR NEAR ANY UNIMPROVED FOREST-COVERED, BRUSH-

COVERED OR GRASS COVERED LAND UNLESS THE

ENGINE'S EXHAUST SYSTEM IS EQUIPPED WITH A SPARK

ARRESTER MEETING APPLICABLE LOCAL LAWS (IF ANY).

IF A SPARK ARRESTER IS USED, IT SHOULD BE MAINTAINED

IN EFFECTIVE WORK ING ORDER BY THE OPERATOR.

IN THE STATE OF CALIFORNIA, A SPARK ARRESTER IS

REQUIRED BY LAW (SECTION 4442 OF THE CALIFORNIA

PUBLIC RESOURCES CODE). OTHER STATES MAY HAVE

SIMILAR LAWS. FEDERAL LAWS APPLY ON FEDERAL LANDS.

SEE YOUR AUTHORIZED SERVICE CENTER/DEPARTMENT

FOR SPARK ARRESTER.

MAINTENANCE ...................................................11-13

SERVICE & ADJUSTMENTS ...............................14-17

STORAGE .................................................................. 18

TROUBLESHOOTING ...............................................19

WARRANTY ...............................................................20

TABLE OF CONTENTS

SAFETY RULES ..........................................................2

CUSTOMER RESPONSIBILITIES ...............................3

PRODUCT SPECIFICATIONS .....................................3

ASSEMBLY ...............................................................4-6

OPERATION ...........................................................7-10

MAINTENANCE SCHEDULE ....................................11

PRODUCT SPECIFICATIONS

Gasoline Capacity: 3 Quarts

Unleaded Reg u lar (2,8L)

OIL (API-SG-SL): SAE 30 Above 32°F/0°C

(Capacity 20 oz/0,6L) SAE 5w30 Below 32°F/0°C

Spark Plug: Champion

RC12YC

(Gap: .030"/0.76mm)

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard

wrench sizes are listed.

(1) Utility knife

(1) Tire pressure gauge

(1) Pair of pliers

(1) 9/16" wrench

OPERATOR’S POSITION (See Fig. 1)

When right or left hand is mentioned in this manual, it

means when you are in the operating position (standing

behind tiller handles).

Your new tiller has been assembled at the factory with exception of those parts left unassembled for shipping purposes.

To ensure safe and proper operation of your tiller all parts and hardware you assemble must be tightened securely. Use

the correct tools as necessary to insure proper tightness.

FRONT

OPERATOR’S

POSITION

LEFT

RIGHT

Fig. 1

(1) Hairpin Clip

(1) Carriage Bolt

3/8-16 UNC x 1 Grade 5

(1) Center Locknut

3/8-16 UNC

(1) Handle Lock Lever

(1) Flat Washer 13/32 x 1 x 11 Gauge

CONTENTS OF HARDWARE PACK

(2) Handle Locks

(1) Pivot Bolt

3/8-16 UNC Grade 5

Extra Shear Pins & Clips

ASSEMBLY

rton_3

han

_10

ASSEMBLY

• Grasp handle assembly. Hold in “up” position. Be sure

handle lock remains in gearcase notch. Slide handle

assembly into position.

HANDLE ASSEMBLY

"UP" POSITION

Fig. 4

UNPACKING CARTON (See Fig. 2)

CAUTION: Be careful of exposed

sta ples when handling or disposing

of cartoning material.

IMPORTANT: WHEN UN PACK ING AND AS SEM BLING TILLER,

BE CAREFUL NOT TO STRETCH OR KINK CABLES.

• While holding handle assembly, cut cable ties se cur ing

handle assembly to top frame and depth stake. Let

handle assembly rest on tiller.

• Remove top frame of carton.

• Slowly ease handle assembly up and place on top of

carton.

• Cut down right hand front and right hand rear cor ners

of carton, lay side carton wall down.

• Remove packing material from handle assembly.

Fig. 2

SHIFT ROD

INSTALL HANDLE (See Figs. 3, 4, and 5)

• Insert one handle lock (with teeth facing outward) in

gearcase notch. (Apply grease on smooth side of

handle lock to aid in keeping lock in place until handle

assembly is lowered into position.)

HANDLE

AS SEM BLY

Fig. 3

HANDLE ASSEMBLY

GEARCASE

NOTCH

HANDLE

LOCK

VIEWED FROM R.H. SIDE OF TILLER

LOOSEN HANDLE

LOCK LEVER TO MOVE

TIGHTEN HANDLE LOCK

LEVER TO HOLD

les_

CARRIAGE

BOLT

SLOT

GEARCASE

HANDLE

LOCK

FLAT

WASHER

HANDLE LOCK

LEVER

PIVOT BOLT

LOCKNUT

HANDLE

BASE

Fig. 5

• Rotate handle assembly down. Insert rear carriage bolt

first, with bolt head on L.H. side of tiller and loosely

assemble locknut (See Fig. 5).

• Insert pivot bolt in front part of plate and tighten.

• Cut down remaining corners of carton and lay panels

flat.

• Lower the handle assembly. Tighten nut on carriage

bolt so handle moves with some resistance. This will

allow for easier adjustment.

• Place flat washer on threaded end of handle lock le-

ver.

• Insert handle lock lever through handle base and

gearcase. Screw in handle lock lever just enough to

hold lever in place.

• Insert second handle lock (with teeth in ward) in the

slot of the handle base (just inside of washer).

• With handle assembly in lowest position, securely

tight en handle lock lever by rotating clockwise. Leav-

ing handle assembly in lowest position will make it

easier to remove tiller from carton.

ASSEMBLY

SHIFT

ROD

HAIRPIN

CLIP

SHIFT

LEVER

INDICATOR

REMOVE TILLER FROM CRATE

• Make sure shift lever indicator is in “N” position (See

Fig. 7)

• Tilt tiller forward by lifting handle. Separate cardboard

cover from leveling shield.

• Rotate tiller handle to the right and pull tiller out of

carton.

CONNECT SHIFT ROD (See Fig. 7)

• Insert end of shift rod into hole of shift lever indicator.

• Insert hairpin clip through hole of shift rod to secure.

Fig. 7

Fig. 6

END OF CLUTCH

CABLE

CONTROL

BAR

CONTROL BAR

BRACKET

CONTROL BAR

BRACKET

CLUTCH

CABLE

ATTACH CLUTCH CABLE (See Fig. 6)

• Hook end of clutch cable through hole in control bar

bracket.

CHECK TIRE PRESSURE

The tires on your unit were overinflated at the factory for

shipping purposes. Correct and equal tire pressure is

important for best tilling performance.

• Reduce tire pressure to 20 PSI (1.4 kg/cm

HANDLE HEIGHT

• Handle height may be adjusted to better suit operator.

(See “TO ADJUST HANDLE HEIGHT” in the Service

and Adjustments section of this manual).

KNOW YOUR TILLER

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TILLER.

Compare the illustrations with your tiller to familiarize yourself with the location of various controls and adjustments. Save

this manual for future reference.

These symbols may appear on your Tiller or in literature supplied with the product. Learn and understand their

meaning.

Fig. 8

MEETS ANSI SAFETY REQUIREMENTS

Our tillers conform to the safety standards of the American National Standards Institute.

CHOKE CONTROL - Used when starting a cold engine.

DEPTH STAKE - Controls depth at which tiller will dig.

DRIVE CONTROL BAR - Used to engage tines.

LEVELING SHIELD - Levels tilled soil.

RECOIL STARTER HANDLE - Used to start the engine.

SHIFT LEVER - Used to shift transmission gears.

SHIFT LEVER INDICATOR - Shows which gear the trans-

mis sion is in.

THROTTLE CONTROL - Controls engine speed.

DRIVE

CONTROL

BAR

DEPTH STAKE

SHIFT LEVER

LEVELING

SHIELD

RECOIL

STARTER

HANDLE

SHIFT LEVER IN DI CA TOR

THROTTLE

CONTROL

CHOKE CONTROL

OPERATION

TURNING

• Release the drive control bar.

• Move throttle control to “SLOW” position.

• Place shift lever indicator in “F” (forward) position. Tines

will not turn.

• Lift handle to raise tines out of ground.

• Swing the handle in the opposite direction you wish

to turn, being careful to keep feet and legs away from

tines.

OPERATION

00155

HOW TO USE YOUR TILLER

Know how to operate all controls before adding fuel and

oil or attempting to start engine.

STOPPING (See Fig. 9)

TINES AND DRIVE

• Release drive control bar to stop movement.

• Move shift lever to “N” (neutral) position.

ENGINE

• Move throttle control to “STOP” position.

• Never use choke to stop engine.

TINE OPERATION - WITH WHEEL DRIVE

• Always release drive control bar before moving shift

lever into another position.

• Tine movement is achieved by moving shift lever to

( ) till position and engaging drive control bar.

FORWARD - WHEELS ONLY/TINES

STOPPED

• Release drive control bar and move shift lever in di ca tor

to “F” (forward) position. Engage drive control bar and

tiller will move forward.

REVERSE - WHEELS ONLY/TINES STOPPED

• DO NOT STAND DIRECTLY BEHIND TILLER.

• Release the drive control bar.

• Move throttle control to “SLOW” position.

• Move shift lever indicator to “R” (reverse) position.

• Hold drive control bar against the handle to start tiller

movement.

HARD TO SHIFT GEARS

• Briefly engage drive control bar and release or rock tiller

forward and backward until are able to shift gears.

DEPTH STAKE (See Fig. 10)

The depth stake can be raised or lowered to allow you more

versatile tilling and cul ti vat ing, or to more easily transport

your tiller.

Fig. 9

pth_st

TILLING (See Fig. 11)

• Release depth stake pin. Pull the depth stake up for

increased tilling depth. Place depth stake pin in hole

of depth stake to lock in position.

• Place shift lever indicator in tilling position.

• Hold the drive control bar against the handle to start

tilling movement. Tines and wheels will both turn.

• Move throttle control to “FAST” position for deep tilling.

To cultivate, throttle control can be set at any desired

speed, depending on how fast or slow you wish to

cultivate.

IMPORTANT: ALWAYS RELEASE DRIVE CONTROL

BAR BEFORE MOVING SHIFT LEVER INTO ANOTHER

POSITION.

TRANSPORT

POSITION

DEEPEST

TILLING

DEPTH

STAKE

SHALLOWEST

TILLING

(CULTIVATING)

Fig. 10

The operation of any tiller can result in foreign objects thrown into the eyes, which can

result in severe eye damage. Always wear safety glasses or eye shields before starting

your tiller and while tilling. We recommend a wide vision safety mask for over spectacles

or standard safety glasses.

DRIVE CONTROL BAR

“ENGAGED” PO SI TION

SHIFT LEVER

DRIVE CONTROL BAR

“DISENGAGED” PO SI TION

depth

ake_16

NUT

“B”

NUT

“A”

SIDE SHIELD

DEPTH STAKE PIN

“RELEASED” POSITION

“LOCKED”

POSITION

Fig. 11

• When you have completed your turn-around, release

the drive control bar and lower handle. Place shift

lever in till position and move throttle control to de sired

speed. To begin tilling, hold drive control bar against

the handle.

TO TRANSPORT

CAUTION: Before lifting or trans port ing,

allow tiller engine and muffler to cool.

Disconnect spark plug wire. Drain

gasoline from fuel tank.

AROUND THE YARD

• Release the depth stake pin. Move the depth stake

down to the top hole for transporting the tiller. Place

depth stake pin in hole of depth stake to lock in posi-

tion. This prevents tines from scuffing the ground.

• Place shift lever indicator in “F” (forward) position for

transporting.

• Hold the drive control bar against the handle to start

tiller movement. Tines will not turn.

• Move throttle control to desired speed.

AROUND TOWN

• Disconnect spark plug wire.

• Drain fuel tank.

• Transport in upright position to prevent oil leakage.

OPERATION

engin

OIL

LEVEL

OIL DRAIN

PLUG

OIL

FILLER

PLUG

Fig. 12

BEFORE STARTING ENGINE

IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT

TO ENTER THE ENGINE WHEN CHECKING OR ADDING

OIL OR FUEL. USE CLEAN OIL AND FUEL AND STORE IN

AP PROVED, CLEAN, COVERED CONTAINERS. USE CLEAN

FILL FUNNELS.

CHECK ENGINE OIL LEVEL (See Fig.12)

• The engine in your unit has been shipped, from the

factory, already filled with SAE 30 summer weight oil.

• With engine level, clean area around oil filler plug and

remove plug.

• Engine oil should be to point of overflowing when engine

is level. For ap proxi mate capacity see “PROD UCT

SPEC I FI CA TIONS” on page 3 of this manual. All oil

must meet A.P.I. Service Classification SG-SL.

• For cold weather operation you should change oil for

easier starting (See oil viscosity chart in the Mainte-

nance sec tion of this manual).

• To change engine oil, see the Maintenance section in

this manual.

TO START ENGINE (See Fig. 13)

CAUTION: Keep drive control bar in

“DISENGAGED” position when start-

ing en gine.

When starting engine for the first time or if engine has run

out of fuel, it will take extra pulls of the recoil starter to

move fuel from the tank to the engine.

• Make sure spark plug wire is prop er ly connected.

• Move shift lever indicator to “N” (neutral) position.

• Place throttle control in “FAST” position.

• Turn fuel shut-off valve 1/4 turn to open position.

• Move choke control to choke position.

• Grasp recoil starter handle with one hand and grasp

tiller handle with other hand. Pull rope out slowly until

engine reaches start of com pres sion cycle (rope will

pull slightly harder at this point).

• Pull recoil starter handle quickly. Do not let starter

handle snap back against starter.

• If engine fires but does not start, move choke control

to half choke position. Pull recoil starter handle until

engine starts.

ADD GASOLINE

• Fill fuel tank to bottom of filler neck. Do not overfill.

Use fresh, clean, regular un lead ed gasoline with a

minimum of 87 octane. (Use of leaded gasoline will

increase carbon and lead oxide deposits and reduce

valve life). Do not mix oil with gasoline. Purchase fuel

in quan ti ties that can be used within 30 days to assure

fuel freshness.

CAUTION: Fill to within 1/2 inch of top

of fuel tank to prevent spills and to allow

for fuel expansion. If gasoline is ac-

ci den tal ly spilled, move machine away

from area of spill. Avoid creating any

source of ignition until gasoline vapors

have disappeared.

Wipe off any spilled oil or fuel. Do not

store, spill or use gasoline near an

open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES

BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE

GAS O LINE TO HELP INSURE GOOD COLD WEATHER

START ING.

CAUTION: Alcohol blended fuels (called

gas o hol or using ethanol or methanol) can at-

tract moisture which leads to sep a ra tion and

for ma tion of acids during storage. Acidic gas

can damage the fuel system of an engine while

in storage. To avoid engine problems, the fuel

system should be emptied before stor age of

30 days or longer. Drain the gas tank, start

the engine and let it run until the fuel lines

and carburetor are empty. Use fresh fuel next

sea son. See Storage In struc tions for additional

information. Never use engine or carburetor

cleaner products in the fuel tank or permanent

damage may occur.

OPERATION

• Soil conditions are important for proper tilling. Tines will

not readily penetrate dry, hard soil which may con trib ute

to excessive bounce and difficult handling of your tiller.

Hard soil should be mois tened before tilling; however,

extremely wet soil will “ball-up” or clump during tilling.

Wait until the soil is less wet in order to achieve the

best results. When tilling in the fall, re move vines and

long grass to prevent them from wrapping around the

tine shaft and slowing your tilling operation.

• Do not lean on handle. This takes weight off the wheels

and reduces traction. To get through a really tough

section of sod or hard ground, apply upward pressure

on handle or lower the depth stake.

321

Fig. 14

CULTIVATING

Cultivating is destroying the weeds between rows to pre-

vent them from robbing nourishment and moisture from the

plants. At the same time, breaking up the upper layer of

soil crust will help retain moisture in the soil. Best digging

depth is 1" to 3" (2.5-7.5 cm). Lower the outer side shields

to protect small plants from being buried.

• Cultivate up and down the rows at a speed which will

allow tines to uproot weeds and leave the ground in

rough condition, promoting no further growth of weeds

and grass (See Fig. 15).

Fig. 15

TILLING HINTS

CAUTION: Until you are accustomed to

handling your tiller, start actual field use

with throttle in slow position (mid-way

between “FAST” and “IDLE”).

• Tilling is digging into, turning over, and breaking up

packed soil before planting. Loose, unpacked soil helps

root growth. Best tilling depth is 4" to 6" (10-15 cm).

A tiller will also clear the soil of unwanted vege ta tion.

The de com po si tion of this vegetable mat ter enriches

the soil. Depending on the climate (rain fall and wind),

it may be advisable to till the soil at the end of the

growing season to further condition the soil.

• You will find tilling much easier if you leave a row

untilled between passes. Then go back between tilled

rows. (See Fig. 14) There are two reasons for doing

this. First, wide turns are much easier to negotiate than

about-faces. Sec ond, the tiller won’t be pulling itself,

and you, toward the row next to it.

Fig. 13

TINE SHEAR PINS

The tine assemblies on your tiller are secured to the tine

shaft with shear pins (See “TINE REPLACEMENT” in the

Service and Ad just ments section of this manual).

If the tiller is unusually overloaded or jammed, the shear

pins are designed to break before internal damage occurs

to the trans mis sion.

• If shear pin(s) break, replace only with those shown in

the Repair Parts section of this manual.

• When engine starts, slowly move choke control to

"RUN" position as engine warms up.

NOTE: A warm engine requires less choking to start.

• Move throttle control to desired running position.

• Allow engine to warm up for a few minutes before

engaging tines.

NOTE: If at a high altitude (3000 feet) or in cold tem per a tures

(below 32°F), the carburetor fuel mixture may need to be

adjusted for best engine performance. See "TO AD JUST

CARBURETOR" in the Service and Adjustments section

of this manual.

NOTE: If engine does not start, see troubleshooting

points.

CHOKE

CON TROL

SPARK PLUG

RECOIL

STARTER

THROTTLE

CONTROL

MAINTENANCE

GENERAL RECOMMENDATIONS

The warranty on this tiller does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must main tain tiller

as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your tiller.

All adjustments in the Service and Adjustments section

of this manual should be checked at least once each

season.

• Once a year you should replace the spark plug, clean

or replace air filter, and check tines and belts for wear.

A new spark plug and clean air filter assure proper

air-fuel mixture and help your engine run better and

last longer.

BEFORE EACH USE

• Check engine oil level.

• Check tine operation.

• Check for loose fasteners.

LUBRICATION

Keep unit well lubricated (See “LUBRICATION CHART”).

SAE 30 OR 10W-30 MOTOR OIL

d REFER TO MAINTENANCE “EN GINE” SECTION

e EP #1 GREASE

LUBRICATION CHART

c WHEEL

HUB

d ENGINE

c IDLER

BRACKET

c LEVELING

SHIELD

HINGES

c DEPTH

STAKE PIN

e RH GEAR CASE

GREASE FITTIG

MAINTENANCE

SCHEDULE

FILL IN DATES

AS YOU COMPLETE

REGULAR SERVICE

Check Engine Oil Level

Change Engine Oil

Oil Pivot Points

Inspect Air Screen

Inspect Spark Arrester / Muffler

Clean or Replace Air Cleaner Cartridge

Clean Engine Cylinder Fins

Replace Spark Plug

BEFORE EACH USE

EVERY 25 HOURS

EVERY 5 HOURS

EVERY 50 HOURS

SERVICE DATES

1,2

1 - Change more often when operating under a heavy load or in high ambient temperatures.

2 - Service more often when operating in dirty or dusty conditions.

EVERY SEASON

RH Gear Case Grease Fitting (1oz.)

AIR CLEANER

CARTRIDGE

COVER

AIR CLEANER

SCREW

MAINTENANCE

OIL FILLER

PLUG

OIL LEVEL

OIL

DRAIN

PLUG

Fig. 16

Disconnect spark plug wire before performing any maintenance (except car bu re tor adjustment) to

prevent accidental start ing of engine.

Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank

before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris.

Do not touch hot muffler or cylinder fins as contact may cause burns.

Fig. 17

TO CHANGE ENGINE OIL (See Figs. 16 and 17)

Determine temperature range expected before oil change.

All oil must meet API service classification SG-SL.

• Be sure tiller is on level surface.

• Oil will drain more freely when warm.

• Use a funnel to prevent oil spill on tiller, and catch oil

in a suitable con tain er.

• Remove drain plug. For easier removal of plug use

7/16 12 Pt. socket with extension.)

• Tip tiller forward to drain oil.

• After oil has drained completely, replace oil drain plug

and tighten securely.

• Remove oil filler plug. Be careful not to allow dirt to

enter the engine.

• Refill engine with oil. See “CHECK ENGINE OIL LEVEL”

in the Operation section of this manual.

ENGINE

LUBRICATION

Use only high quality detergent oil rated with API service

classification SG-SL. Select the oil’s SAE vis cos i ty grade

according to your expected temperature.

NOTE: Although multi-viscosity oils (5W-30, 10W-30, etc.)

improve starting in cold weather, these multi-viscosity oils

will result in increased oil consumption when used above

40°F (4°C). Check your engine oil level more frequently to

avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at

least once a year if the tiller is not used for 25 hours in

one year.

Check the crankcase oil level before starting the engine

and after each five (5) hours of continuous use. Add SAE

30 motor oil or equivalent. Tighten oil filler plug securely

each time you check the oil level.

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

SAE VISCOSITY GRADES

-20 0 30 40

100

-30

-20 4

20 30 40

-10

10W-30 / 5W-30

SAE 30

oil_visc_chart5_e(drt)

Fig. 18

AIR CLEANER (See Fig. 18)

Service air cleaner cartridge every twenty-five hours, more

often if engine is used in very dusty conditions.

• Loosen air cleaner screws, one on each side of

cover.

• Remove air cleaner cover.

• Carefully remove air cleaner cartridge. Be care ful. Do

not allow dirt or de bris to fall into carburetor.

• Clean by tapping gently on a flat surface.

• If very dirty or damaged, replace cartridge.

• Clean and re place cover. Tighten screws securely.

IMPORTANT: PETROLEUM SOLVENTS, SUCH AS KER O SENE,

ARE NOT TO BE USED TO CLEAN THE CAR TRIDGE. THEY

MAY CAUSE DETERIORATION OF THE CARTRIDGE. DO

NOT OIL CARTRIDGE. DO NOT USE PRESSURIZED AIR TO

CLEAN OR DRY CARTRIDGE.

COOLING SYSTEM (See Fig. 19)

Your engine is air cooled. For proper engine performance

and long life keep your engine clean.

• Clean air screen frequently using a stiff-bristled

brush.

• Keep cylinder fins, levers, and linkage free of dirt and

chaff.

MAINTENANCE

Fig. 19

MUFFLER

Do not operate tiller without muffler. Do not tamper with

exhaust system. Damaged mufflers or spark arresters could

create a fire hazard. Inspect pe ri odi cally and re place if

nec es sary. If your engine is equipped with a spark arrester

screen assembly, re move every 50 hours for cleaning and

inspection. Re place if dam aged.

SPARK PLUG

Replace spark plugs at the beginning of each tilling sea-

son or after every 50 hours of use, whichever comes first.

Spark plug type and gap setting is shown in “PRODUCT

SPEC I FI CA TIONS” on page 3 of this manual.

TRANSMISSION

Once a season, lubricate the right hand side gear case

grease fitting with 1 oz. of EP #1 Grease.

CLEANING

Do not clean your tiller when the engine and transmission

are hot. We do not rec om mend using pressurized water

(gar den hose, etc.) to clean your unit un less the gasket

area around the trans mis sion and the engine muf fler, air

fil ter and car bu re tor are cov ered to keep wa ter out. Wa ter

in en gine will short en the useful life of your tiller.

• Clean engine, wheels, finish, etc. of all foreign mat-

ter.

• Keep finished surfaces and wheels free of all gas o line,

oil, etc.

• Protect painted surfaces with au to mo tive type wax.

AIR SCREEN

BLOW ER

HOUS ING

MUFFLER

CYLINDER FINS

SERVICE AND ADJUSTMENTS

CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come

into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT (See Fig. 20)

Select handle height best suited for your tilling conditions.

Handle height will be different when tiller digs into soil.

• First loosen handle lock lever.

• Handle can be positioned at different settings between

“HIGH” and “LOW” positions.

• Retighten handle lock lever securely after adjusting.

Fig. 20

HANDLE

(LOW POSITION)

HANDLE LOCK

LEVER

HANDLE

(HIGH POSITION)

Fig. 22

SCREW

AND

WASHER

HEX NUT

AND WASHER

(LOCATED

BEHIND

TIRE)

BELT GUARD

SCREW

AND WASHER

HAIRPIN CLIP AND

CLEVIS PIN

TO REMOVE BELT GUARD (See Fig. 22)

NOTE: For ease of removal, remove hairpin clip and

clevis pin from left wheel. Pull wheel out from tiller about

1 inch.

• Remove two (2) screws from side of belt guard.

• Remove hex nut and washer from bottom of belt guard

(located behind wheel).

• Pull belt guard out and away from unit.

• Replace belt guard by reversing above procedure.

TIRE CARE

CAUTION: When mounting tires, un-

less beads are seated, over in fla tion

can cause an explosion.

• Maintain 20 pounds of tire pressure. If tire pressures

are not equal, tiller will pull to one side.

• Keep tires free of gasoline or oil which can damage

rubber.

TO REMOVE WHEEL (See Fig. 21)

• Place blocks under trans mis sion to keep tiller from

tipping.

• Remove hairpin clip and clevis pin from wheel.

• Remove wheel and tire.

• Repair tire and reassemble.

CLEVIS PIN

HAIRPIN CLIP

Fig. 21

SERVICE AND ADJUSTMENTS

CABLE CLIP

SCREW

DRIVE

CONTROL

CABLE

EXTENSION

SPRING

ENGINE

PULLEY

IDLER

PULLEY

TRANS MIS SION PULLEY

LESS

TEN SION

5/8"

TEN SION

TO REPLACE GROUND DRIVE BELT

(See Fig. 23)

• Remove belt guard (See “TO REMOVE BELT GUARD”

in this section of this manual).

• Remove old belt by slipping off engine pulley first then

remove from transmission pulley.

• Place new belt in groove of transmission pulley and

into engine pulley. BELT MUST BE IN GROOVE ON

TOP OF IDLER PULLEY. NOTE POSITION OF BELT

TO GUIDES.

• Check belt adjustment as described below.

• Replace belt guard.

• Reposition wheel and replace clevis pin and hairpin

clip.

Fig. 23

GROUND DRIVE BELT ADJUSTMENT

(See Fig. 23)

For proper belt tension, the extension spring should

have about 5/8 inch stretch when drive control bar is in

“EN GAGED” position. This tension can be attained as

follows:

• Loosen cable clip screw securing the drive control

cable.

• Slide cable forward for less tension and rearward for

more tension until about 5/8 inch stretch is obtained

while the drive control bar is engaged.

• Tighten cable clip screw securely.

SERVICE AND ADJUSTMENTS

Fig. 25

• To maintain the superb tilling performance of this ma-

chine the tines should be checked for sharpness, wear,

and bending, particularly the tines which are next to

the transmission. If the gap between the tines ex ceeds

3-1/2 inches they should be replaced or straight ened

as necessary.

• New tines should be assembled as shown in Fig.

26. Sharp ened tine edges will rotate rearward from

above.

Fig. 26

TINE REPLACEMENT (See Figs. 24, 25 and

26)

CAUTION: Tines are sharp. Wear

gloves or other protection when han-

dling tines.

A badly worn tine causes your tiller to work harder and dig

more shallow. Most important, worn tines cannot chop and

shred organic matter as effectively nor bury it as deeply as

good tines. A tine this worn needs to be replaced.

NEW TINE

WORN TINE

Fig.24

tine_13

SHARP EDGE

HAIRPIN CLIP

SHARP

EDGES

COUNTER

TINE

ROTATION

SHARP EDGES

SHARP EDGE

SHEAR PIN

HAIRPIN CLIP

SHARP

EDGE

tine_3

TINE

3-1/2" MAX

(9 CM)

TRANS MIS SION

SERVICE AND ADJUSTMENTS

ENGINE

TO AD JUST CARBURETOR

The carburetor has been preset at the factory and ad just ment

should not be necessary. However, engine per for mance

can be affected by dif fer enc es in fuel, tem per a ture, al ti tude

or load. If the carburetor does need ad just ment, contact

your nearest authorized service center/de part ment

IMPORTANT: NEVER TAMPER WITH THE ENGINE

GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE

SPEED. OVER SPEED ING THE ENGINE ABOVE THE FACTORY

HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK

THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING,

CONTACT YOUR NEAREST AUTHORIZED SERVICE CENTER/

DEPARTMENT, WHICH HAS THE PROPER EQUIP MENT AND

EXPERIENCE TO MAKE ANY NEC ES SARY ADJUSTMENTS.

Immediately prepare your tiller for storage at the end of the

season or if the unit will not be used for 30 days or more.

WARNING: Never store the tiller with

gasoline in the tank inside a build ing

where fumes may reach an open flame

or spark. Allow the engine to cool before

storing in any en clo sure.

TILLER

• Clean entire tiller (See “CLEANING” in the Maintenance

section of this manual).

• Inspect and replace belts, if necessary (See belt re-

place ment instructions in the Service and Ad just ments

section of this manual).

• Lubricate as shown in the Maintenance section of this

manual.

• Be sure that all nuts, bolts and screws are securely

fastened. Inspect moving parts for damage, break age

and wear. Replace if necessary.

• Touch up all rusted or chipped paint surfaces; sand

lightly before painting.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS

FROM FORMING IN ES SEN TIAL FUEL SYS TEM PARTS SUCH

AS THE CAR BU RE TOR, FUEL FILTER, FUEL HOSE, OR TANK

DURING STOR AGE. ALSO, EXPERIENCE INDICATES THAT

AL CO HOL BLENDED FUELS (CALLED GASOHOL OR USING

ETHA NOL OR METHA NOL) CAN ATTRACT MOIS TURE WHICH

LEADS TO SEPA RA TION AND FORMATION OF ACIDS DUR ING

STOR AGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM

OF AN ENGINE WHILE IN STOR AGE.

• Empty the fuel tank by starting the engine and let it run

until the fuel lines and carburetor are empty.

• Never use engine or carburetor cleaner products in the

fuel tank or permanent.

• Use fresh fuel next season.

NOTE: Fuel stablizer is an acceptable alternative in

minimizing the formation of fuel gum deposits during

storage. Add stabilizer to gasoline in fuel tank or storage

container. Always follow the mix ratio found on stablizer

container. Run engine at least 10 minutes after adding

stablizer to allow the stabilizer to reach the carburetor.

Do not empty the gas tank and carburetor if using fuel

stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean oil. (See

“ENGINE” in the Maintenance section of this man ual).

CYLINDER(S)

• Remove spark plug.

• Pour 1 ounce (29 ml) of oil through spark plug hole into

cylinder.

• Pull starter handle slowly several times to distribute

oil.

• Replace with new spark plug.

OTHER

• Do not store gasoline from one season to an-

other.

• Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

• If possible, store your unit indoors and cover it to give

protection from dust and dirt.

• Cover your unit with a suitable protective cover that

does not retain moisture. Do not use plastic. Plastic

cannot breathe which allows condensation to form and

will cause your unit to rust.

IMPORTANT: NEVER COVER TILLER WHILE EN GINE AND

EX HAUST AREAS ARE STILL WARM.

STORAGE

Will not start 1. Out of fuel. 1. Fill fuel tank.

2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section.

3. Engine flooded. 3. Wait several minutes before attempting to start.

4. Dirty air cleaner. 4. Clean or replace air cleaner cartridge.

5. Water in fuel. 5. Empty fuel tank and carburetor, and refill tank with fresh,

clean gasoline.

6. Clogged fuel tank. 6. Remove fuel tank and clean.

7. Loose spark plug wire. 7. Make sure spark plug wire is seated properly on plug.

8. Bad spark plug or improper gap. 8. Replace spark plug or adjust gap.

9. Carburetor out of adjustment. 9. Make necessary adjustments.

10. Oil soaked air filter. 10. Replace air filter.

Hard to start 1. Throttle control not set properly. 1. Place throttle control in “FAST” position.

2. Dirty air cleaner. 2. Clean or replace air cleaner cartridge.

3. Bad spark plug or improper gap. 3. Replace spark plug or adjust gap.

4. Stale or dirty fuel. 4. Empty fuel tank and refill tank with fresh, clean gasoline.

5. Loose spark plug wire. 5. Make sure spark plug wire is seated properly on plug.

6. Carburetor out of adjustment. 6. Make necessary adjustments.

Loss of power 1. Engine is overloaded. 1. Set depth stake for shallower tilling.

2. Dirty air cleaner. 2. Clean or replace air cleaner cartridge.

3. Low oil level/dirty oil. 3. Check oil level/change oil.

4. Faulty spark plug. 4. Clean and regap or change spark plug.

5. Oil in fuel. 5. Empty and clean fuel tank and refill tank, and clean

car bu re tor.

6. Stale or dirty fuel. 6. Empty fuel tank and refill tank with fresh, clean gasoline.

7. Water in fuel. 7. Empty fuel tank and carburetor, and refill tank with fresh,

clean gasoline.

8. Clogged fuel tank. 8. Remove fuel tank and clean.

9. Spark plug wire loose. 9. Connect and tighten spark plug wire.

10. Dirty engine air screen. 10. Clean engine air screen.

11. Dirty/clogged muffler. 11. Clean/replace muffler.

12. Carburetor out of adjustment. 12. Make necessary adjustments.

13. Poor compression. 13. Contact an authorized service center/department.

Engine overheats 1. Low oil level/dirty oil. 1. Check oil level/change oil.

2. Dirty engine air screen. 2. Clean engine air screen.

3. Dirty engine. 3. Clean cylinder fins, air screen, and muffler area.

4. Partially plugged muffler. 4. Remove and clean muffler.

5. Improper carburetor adjustment. 5. Adjust carburetor to richer position.

Excessive bounce/ 1. Ground too dry and hard. 1. Moisten ground or wait for more favorable soil

difficult handling conditions.

Soil balls up or clumps 1. Ground too wet. 1. Wait for more favorable soil conditions.

Engine runs but tiller 1. Drive control bar is not engaged. 1. Engage drive control.

won’t move 2. V-belt not correctly adjusted. 2. Inspect/adjust V-belt.

3. V-belt is off pulley(s). 3. Inspect V-belt.

Engine runs but labors 1. Tilling too deep. 1. Set depth stake for shallower tilling.

when tilling 2. Throttle control not properly adjusted. 2. Check throttle control setting.

3. Carburetor out of adjustment. 3. Make necessary adjustments.

Tines will not rotate 1. Shear pin(s) broken. 1. Replace shear pin(s).

PROBLEM CAUSE CORRECTION

TROUBLESHOOTING POINTS

LIMITED WARRANTY

The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de-

fects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer

purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any

part which we find to be defective due to materials or workmanship. This Warranty is subject to the following limita-

tions and exclusions.

1. This warranty does not apply to the engine or components parts thereof. Please refer to the applicable manu-

facturer's warranty on these items.

2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of

the pur chaser. Transportation charges for any parts submitted for replacement under this warranty must be paid

by the purchaser unless such return is requested by the manufacturer.

3. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date

of original purchase.

4. This Warranty applies only to products which have been properly assembled, adjusted, operated, and main-

tained in ac cor dance with the instructions furnished. This Warranty does not apply to any product which has

been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal

wear of the product.

5. Exclusions: Excluded from this Warranty are belts, tines, tine adapters, normal wear, normal adjustments, stan-

dard hard ware and normal maintenance.

6. In the event you have a claim under this Warranty, you must return the product to an authorized service deal-

er.

Should you have any unanswered questions concerning this Warranty, please contact:

giving the model number, serial number and date of purchase of your product and the name and address of the

authorized dealer from whom it was purchased.

THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED

WAR RAN TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WAR-

RANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied

Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific

legal rights, and you may have other rights which vary from locale to locale.

This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.

In Canada contact:

HOP

7075 Ordan Drive

Mississauga, Ontario

L5T 1K6

HOP

Customer Service Dept.

1030 Stevens Creek Road

Augusta, GA 30907 USA

La page charge ...

Poulan Pro 96092002200 Manuel utilisateur

Marque: Poulan Pro

Modèle: 96092002200

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Poulan Pro 96092002200 User manual

Poulan Pro 96092002200 Manuel utilisateur

Poulan Pro 96092002200 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents