MTD Tiller 450 Manuel utilisateur

Marque: MTD

Modèle: Tiller 450

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

Ce manuel convient également à

IMPORTANT: READ

MTD PRODUCTS LTD. P.O. BOX 1386 KITCHENER, ON N2G 4J1

REAR TINE

TILLER

MODEL

450 Series

PRINTED IN THE U.S.A.

772C0731

SAFETY RULES AND

INSTRUCTIONS CAREFULLY

(10/04)

OPERATOR’S MANUAL

TABLE OF CONTENTS

FINDING MODEL NUMBER

This Operator’s Manual is an important part of your new equipment. It will help you assemble, prepare and maintain the unit for

best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the equipment and copy the

information from it in the space provided below. A sample model plate is also given below. You can locate the model

plate by standing at the operating position and looking down at the rear of the deck . This information will be

necessary to use the manufacturer’s web site and/or help from the Customer Support Department or an authorized

service dealer.

ENGINE INFORMATION

The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating, specifications,

warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual packed separately with your unit for

more information.

CALLING CUSTOMER SUPPORT

Please do NOT return the unit to the retailer from which it was purchased, without first contacting Customer Support.

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance

of this unit, please call a Customer Support Representataive.

For US Customers: 1- (330) 220-4MTD (4683) or 1- (800)-800-7310

For Canadian Customers: 1-800-668-1238

Please have your unit’s model number and serial number ready when you call. See previous section to locate this information.

You will be asked to enter the serial number in order to process your call.

HOW TO OBTAIN SERVICE

Service is available, WITH PROOF OF PURCHASE, through your local authorized service dealer. To locate the

dealer in your area;

In the U.S.A.

: Check your Yellow Pages, or contact customer support listed about MTD LLC at P.O. Box 361131,

Cleveland, Ohio 44136-0019, or call 1-800-800-7310 or 1-330-220-4683 or log on to our Web site at

www.mtdproducts.com.

In Canada

: Contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 1-800-668-1238 or log on to our Web

site at www.mtdcanada.com.

Content Page

Customer Support 2

Important Safe Operation Practices 3

Loose Parts 5

Assembly 6

Controls 8

Operation 9

How To Use Your Tiller 10

Adjustments 11

Lubrication 11

Maintenance 11

Off-Season Storage 12

Trouble Shooting Guide 13

Parts Lists/Pièces détachées 14

Warranty 20

Content Page

MTD PRODUCTS LIMITED

KITCHENER, ON N2G 4J1

1-800-668-1238

XXXXXXXXXX

XXXXXXXXXXX

Model Number

Numéro de modèle

Serial Number

Numéro de série

www.mtdcanada.com

This is where your model number will be.

This is where your serial number will be.

Copy the model number here:

Copy the serial number here:

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could endanger

the personal safety and/or property of yourself and others. Read and follow all instructions in this manual

before attempting to operate your tiller. Failure to comply with these instructions may result in personal

injury. when you see this symbol— HEED ITS WARNING

DANGER: Your tiller was built to be operated according to the rules for safe operation in this manual.

As with any type of power equipment, carelessness or error on the part of the operator can result in

serious injury. This tiller is capable of amputating hands and feet. Failure to observe the following safety

instructions could result in serious injury or death.

TRAINING

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe

place for future and regular reference and for

ordering replacement parts.

2. Be familiar with all controls and their proper

operation. Know how to stop the machine and

disengage them quickly.

3. Never allow children under 14 years old to operate

this machine. Children 14 years old and over should

read and understand the operation instructions and

safety rules in this manual and should be trained

and supervised by a parent.

4. Never allow adults to operate this machine without

proper instruction.

5. Keep bystanders, helpers, children and pets at

least 75 feet from the machine while it is in

operation. Stop machine if anyone enters the area.

PREPARATION

1. Thoroughly inspect the area where the equipment

is to be used. Remove all stones, sticks, wire, and

other foreign objects which could be tripped over

and cause personal injury.

2. Wear sturdy, rough-soled work shoes and close-

fitting slacks and shirts. Loose fitting clothes and

jewelry can be caught in movable parts. Never

operate this machine in bare feet or sandals.

3. Disengage clutch levers and shift (if provided)

lever into neutral ("N") before starting the engine.

4. Never leave this machine unattended with the

engine running.

5. Never attempt to make any adjustments while the

engine is running, except where specifically

recommended in the operator’s manual.

6. To avoid personal injury or property damage use

extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are

explosive. Serious personal injury can occur when

gasoline is spilled on yourself or your clothes

which can ignite. Wash your skin and change

clothes immediately.

7. Use only an approved gasoline container.

8. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

9. Never fuel machine indoors.

10. Never remove gas cap or add fuel while the

engine is hot or running.

11. Allow engine to cool at least two minutes before

refueling.

12. Never over fill fuel tank. Fill tank to no more than

½ inch below bottom of filler neck to allow space

for fuel expansion.

13. Replace gasoline cap and tighten securely.

14. If gasoline is spilled, wipe it off the engine and

equipment. Move unit to another area. Wait 5

minutes before starting the engine.

15. Never store the machine or fuel container inside

where there is an open flame, spark or pilot light

as on a water heater, space heater, furnace,

clothes dryer or other gas appliances.

16. Allow a machine to cool at least 5 minutes before

storing.

OPERATION

1. Do not put hands or feet near rotating parts.

Contact with the rotating parts can amputate

hands and feet.

2. Do not operate the machine while under the

influence of alcohol or drugs.

3. Never operate this machine without good visibility

or light. Always be sure of your footing and keep a

firm hold on the handles.

4. Keep bystanders, helpers, children and pets at

least 75 feet from the machine while it is in

operation. Stop machine if anyone enters the area.

5. Be careful when tilling in hard ground. The tines

may catch in the ground and propel the tiller

forward. If this occurs, let go of the handle bars and

do not restrain the machine.

6. Exercise extreme caution when operating on or

crossing gravel surfaces. Stay alert for hidden

hazards or traffic. Do not carry passengers.

7. Never operate the machine at high transport

speeds on hard or slippery surfaces.

8. Exercise caution to avoid slipping or falling.

9. Look down and behind and use care when in

reverse or pulling machine towards you.

10. Start the engine according to the instructions

found in this manual and keep feet well away from

the tines at all times.

11. After striking a foreign object, stop the engine,

disconnect the spark plug wire(s) and ground

against the engine. Thoroughly inspect the

machine for any damage. Repair the damage

before starting and operating.

12. Disengage all clutch levers and stop the engine

before you leave the operating position (behind the

handles). Wait until the tines come to a complete

stop before unclogging the tines, making any

adjustments, or inspections.

13. Never run an engine indoors or in a poorly

ventilated area. Engine exhaust contains carbon

monoxide, an odorless, and deadly gas.

14. Muffler and engine become hot and can cause a

burn. Do not touch.

15. Use caution when tilling near fences, buildings and

underground utilities. Rotating tines can cause

property damage or personal injury.

16. Do not overload machine capacity by attempting to

till soil too deep at too fast of a rate.

17. If the machine should start making unusual noise

or vibration, stop the engine, disconnect the spark

plug wire and ground it against the engine. Inspect

thoroughly for damage. Repair any damage before

starting and operating.

18. Keep all shields, guards and safety devices in

place and operating properly.

19. Never pick up or carry machine while the engine is

running.

20. Use only accessories and attachments approved

for this machine by the machine manufacturer.

Failure to do so, can result in serious injury.

21. If situations occur which are not covered in this

manual, use care and good judgment. Contact

your authorized dealer for assistance.

MAINTENANCE & STORAGE

1. Never tamper with safety devices. Check their

proper operation regularly.

2. Check bolts and screws for proper tightness at

frequent intervals to keep the machine in safe

working condition. Also, visually inspect machine

for any damage.

3. Before cleaning, repairing, or inspecting, make

certain the tine(s) and all moving parts have

stopped. Disconnect the spark plug wire and

ground against the engine to prevent unintended

starting.

4. Do not change the engine governor settings or

over-speed the engine. The governor controls the

maximum safe operating speed of the engine.

5. Maintain or replace safety and instruction labels,

as necessary.

6. Follow this manual for safe loading, unloading,

transporting, and storage of this machine.

7. Never store the machine or fuel container inside

where there is an open flame, spark or pilot light

as on a water heater, space heater, furnace,

clothes dryer or other gas appliances.

8. Always refer to the operator’s manual for proper

instructions on off-season storage.

9. If the fuel tank has to be drained, do this outdoors.

10. Observe proper disposal laws and regulations for

gas, oil, etc. to protect the environment.

WARNING — YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read,

understand and follow the warnings and instructions in this manual and on the machine.

Figure 1 Safety labels found on your unit

SECTION 2: LOOSE PARTS

Handle

Assembly

Depth

Stake

Assembly

Control

Rod

NOTE: All hardware needed for assembly is attached to the loose parts or the tiller.

NOTE: Cable tie not shown.

SECTION 3: ASSEMBLY INSTRUCTIONS

IMPORTANT: This unit is shipped WITHOUT

GASOLINE or OIL. After assembly, see separate

engine manual for proper fuel and engine oil

recommendations.

NOTE: Left and right is determined from the

operator’s position, standing behind the tiller.

TOOLS REQUIRED FOR ASSEMBLY

Adjustable Wrenches

Pair of Pliers

Screw Driver

TO REMOVE UNIT FROM CARTON

1. Remove staples, break glue on top flaps, or cut

tape at carton end and peel along top flap to open

carton.

2. Remove loose parts included with unit (i.e.,

operator’s manual, etc.).

3. Cut corners and lay carton down flat.

4. Remove packing material.

5. Roll or slide unit out of carton. Check carton

thoroughly for loose parts.

6. Extend control cable and lay on the floor. Be

careful not to bend or kink control cable.

Figure 1

WARNING: Disconnect the spark plug

wire and ground against the engine to

prevent unintended starting.

ATTACHING DEPTH STAKE ASSEMBLY

1. Tip the tiller forward so it rests on front

counterweight.

2. Raise the tine shield hinge flap assembly. Remove

"T" knob, flat washer and hex bolt from depth

stake. Insert the depth stake assembly in front of

spacer (under the tine shield) and up through the

tine shield assembly as shown in Figure 1.

3. Insert clevis pin through the tine shield and the

second hole from top of the depth stake. Secure

with hairpin clip.

4. Insert hex bolt into the top hole of the depth stake

assembly. Place flat washer on hex bolt and

thread “T” knob onto the hex bolt. See Figure 1.

Tighten securely.

5. Tip the tiller back down so it rests on the depth

stake (transport position).

ATTACHING THE HANDLE ASSEMBLY

Figure 2

1. Remove top two bolts and flange lock nuts from

handle mounting brackets as shown in Figure 2.

Do not remove the bottom bolt and nut.

2. Place handle assembly in position between the

handle mounting brackets. See Figure 2.

3. Line up holes in handle with holes in handle

mounting brackets. Secure with hardware

removed in step 1.

T-Knob

Flat Washer

Hex Bolt

Hairpin Clip

Clevis Pin

Depth Stake

Rear Tine

Shield

Remove

Handle

Assembly

Handle

Bracket

Figure 3

ATTACHING THE CLUTCH CABLE

Attach the clutch cable to the handle as follows (be

careful not to kink the cable).

1. Remove threaded eyebolt and nut from the end of

the cable.

2. Route the clutch cable to the right side of the

handle mounting brackets and underneath the

handle.

3. Push the cable through the hole in the center of

the handle and snap in the plastic fitting. See

Figure 3.

4. Remove slot head screw, nut and two flat washers

from the clutch bail.

5. Fasten the threaded eyebolt onto bail as shown in

Figure 4. The parts go together from top to bottom

as follows: Slot Head Screw, Flat Washer, Clip,

Eyebolt, Flat Washer and 1/4” Nut.

6. Thread eyebolt and #10 nut, removed in step 1,

into the internally threaded tube at the end of the

cable. Thread engagement should be about 3/4”.

Tighten nut against tube at end of cable. See

Figure 4.

NOTE: Do not overtighten control wire. Too much

tension may cause it to break.

WARNING:

Be certain to check the

clutch cable adjustment before operating

the tiller.

Figure 4

ATTACHING THE CONTROL ROD

• Make sure the handle assembly is in the highest

position.

• Remove hairpin clips from control rod, (rubber

washers to remain on control rod).

• Insert the shorter, (angled), end of the control rod

through the indicator bracket on the shift cover and

secure with hairpin clip that was removed in step 1.

See Figure 5.

• Insert the longer end of the control rod through the

hole in the gear selector handle and secure with

hairpin clip.See Figure 6.

Figure 5

CHECKING THE CLUTCH ADJUSTMENT

IMPORTANT:

Service the engine with oil and

gasoline before checking this adjustment. Refer to the

separate engine manual packed with your tiller for

proper fuel and engine oil recommendations.

Position the tiller so the front counterweight is against

a solid object, such as a wall. With the gear selection

lever in NEUTRAL, start the engine. Refer to the

separate engine manual.

Standing on the right side of the tiller, examine the belt

(inside the belt cover). It should not be turning.

Plastic Fitting

Internally Threaded

Tube

Slot Head Screw,

Nut, Flat Washers

Slot Head Screw

Flat Washers

Threaded

Eyebolt

Internally

Threaded

Tube

Clutch

Bail

”

1/4”

Nut

#10

Nut

Control Rod

Rubber

Washer

Indicator Bracket

Hairpin Clip

Idler Pulley Rod

WARNING: Do not put fingers under the

belt cover.

If the belt turns without bail engaged, adjust by

unthreading the internally threaded tube at the end of

the cable a few turns clockwise (when standing in

operator’s position), and then retighten the nut against

the tube.

Now move the shift lever to FORWARD (Wheels

Forward) position. Carefully engage the clutch by lifting

the clutch control bail against the handle. The wheels

should spin.

If the wheels do not spin with the unit in forward,

adjust by unthreading the tube at the end of the cable a

few turns counter-clockwise, (when standing in

operator’s position), and then retighten the nut against

the tube.

Recheck both adjustments, and readjust as necessary.

NOTE: A secondary cable adjustment is available if

you reach the point that additional adjustment is

needed. Remove the belt cover and move the hex nuts

at the other end of the cable towards the end of the

casing. Then readjust the hex nuts at the handle.

TIRE PRESSURE

The tires on your unit may be over-inflated for shipping

purposes. Reduce the tire pressure before operating

the unit. Recommended operating tire pressure is

approximately 20 p.s.i. (check sidewall of tire for tire

manufacturer’s recommended pressure).

WARNING: Maximum tire pressure

under any circumstances is 30 p.s.i. Equal

tire pressure should be maintained on

both tires.

SECTION 4: CONTROLS

THROTTLE CONTROL

The throttle control lever is located on the engine. It

controls the engine speed and stops the engine. See

Engine manual for further information.

CHOKE LEVER (if equipped)

The choke lever is located to the left of the throttle. It is

used to enrich the fuel mixture in the carburetor when

starting a cold engine. See Engine manual for further

information.

Figure 6

GEAR SELECTION HANDLE

The gear selection handle is located in the center of

the handle on the tiller. It is used to select NEUTRAL,

REVERSE, or one of the FORWARD modes (see

below). Pull or push the handle so that the indicator on

top of shift cover points to the operating mode desired.

See Figure 6.

NEUTRAL—Transmission is in neutral.

REVERSE—Reverse wheel drive.

FORWARD Modes:

Wheels Forward— Forward wheel drive only.

Tines Reverse— Forward wheel drive and reverse

tine drive.

Tines Forward— Forward wheel and tine drive.

IMPORTANT: Use the reverse tine drive when

tilling virgin ground, sod, or hard soil. Use the forward

tine drive when cultivating or tilling soft ground.

NOTE: If difficulty is encountered in moving the gear

selection handle, move the tiller forward or backward

slightly to allow the gears to synchronize.

• To shift into forward or reverse wheel drive,

move tiller forward slightly then backward to

allow the gears to synchronize.

• To shift into forward wheels and tine drive, push

forward slightly on the gear selection handle and

slowly engage the clutch control allowing the

gears to synchronize.

• To stop forward movement and tine drive,

release the clutch control. Do not shift gears

with the clutch control engaged except when

engaging the tines.

WARNING: Make certain unit is in

NEUTRAL when starting the engine.

Height

Adjustment

Lever

Control

Rod

Gear

Selection

Handle

Clutch

Control

Bail

Clutch

Cable

Cable Tie

DEPTH STAKE

The depth bar controls the tilling depth. Refer to

SECTION 6: HOW TO USE YOUR TILLER on page

10.

ENGINE CONTROLS

See the separate engine manual for additional

information and functions of the engine controls.

PRIMER BUTTON (if equipped)

The primer button is located behind the air cleaner. It

is used to enrich the fuel mixture in the carburetor

when starting a cold engine.

HANDLE ADJUSTMENT

The handle may be adjusted to be raised or lowered in

line with the tiller. To adjust the handle position loosen

the handle height adjustment crank a few turns. Pivot

handle up or down to desired position. Tighten crank.

See Figure 6.

CLUTCH CONTROL BAIL

The clutch control bail is located below the handle.

See Figure 6. Lifting the clutch control bail against the

handle engages the wheel and tine drive mechanisms.

NOTE: Never engage clutch lever while shifting.

SECTION 5: OPERATION

NOTE: Engine is shipped WITHOUT oil.

WARNING: Read, understand, and

follow all instructions and warnings on

the machine and in this manual before

operating.

BEFORE STARTING

Service engine with gasoline and oil as instructed in

the separate engine manual packed with your tiller.

Read instructions carefully.

WARNING: Use extreme care when

handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

Never fuel machine indoors or while the

engine is hot or running.

TO START ENGINE

NOTE: When pushing the unit with the engine off,

you will hear a ratcheting sound (gear noise) which is

normal.

WARNING: Be Sure No One Is Standing

In Front Of The Tiller While The Engine Is

Running Or Being Started.

1. Place gear selection lever in NEUTRAL.

2. Place the throttle control lever in the FAST (rabbit)

position. Place the engine speed control in the

START position.

3. Move choke lever to CHOKE position or if

equipped, push primer two (2) or three (3) times.

Wait about two (2) seconds between each push.

NOTE: A warm engine may not require choking.

4. Stand at side of tiller. Grasp the starter handle and

pull out slowly, until it pulls slightly harder. Let rope

rewind slowly.

5. Pull starter handle rapidly. Do not allow handle to

snap back. Allow it to rewind slowly while keeping

a firm hold on the starter handle.

6. Repeat steps 3 and 4 until engine starts.

7. As engine warms up and begins to operate evenly,

move choke lever gradually to RUN position. If

engine falters, return to choke position, then slowly

move to RUN position.

NOTE: Refer to engine manual for additional engine

information.

NOTE: After starting engine and prior to using the

tiller, be certain to check the clutch adjustment as

described in “Checking the Clutch Adjustment” section

of Assembly Instructions.

TO STOP ENGINE

1. Move throttle control to the STOP position.

2. Disconnect spark plug wire and ground to prevent

accidentally starting while equipment is

unattended.

NOTE: After the first ten hours of operation, recheck

the clutch adjustment. Refer to “Checking the Clutch

Adjustment” section of the Assembly Instructions.

SECTION 6: HOW TO USE YOUR TILLER

WARNING: Be certain the spark plug

wire is disconnected and grounded

against the engine when performing any

adjustments.

Tilling depth is controlled by the depth stake which can

be adjusted to five different settings. See Figure 7.

Adjust the side shields as shown in Figure 7, as you

adjust the depth stake. Be certain spark plug wire is

disconnected and grounded against the engine.

1. When using the tiller for the first time, use the

second adjustment hole from the top (1" of tilling

depth). See Figure 7.

2. When breaking up sod and for shallow cultivation,

use the setting which gives 1" of tilling depth

(second hole from the top). Place the side shields

in their lowest position. For further depth, raise the

depth stake and side shields and make one or two

more passes over the area.

3. When tilling loose soil, depth stake may be raised

to its highest position (use bottom adjustment

hole) to give the deepest tilling depth. Raise the

side shields to their highest position.

4. To transport tiller, lower the depth stake (use top

adjustment hole).

To adjust the depth stake, remove the clevis pin and

hairpin clip. See Figure 7. Move the depth stake to the

desired setting and secure with the clevis pin and

hairpin clip.

To adjust the side shields, remove the wing nuts. See

Figure 7. Place side shield in position desired. Replace

wing nuts and tighten securely.

TO OPERATE THE TILLER:

1. Select the depth stake setting.

2. Start engine as instructed on page 9.

3. Move gear selection handle to one of the forward

modes or reverse.

WARNING: Do not move the gear

selection handle with the wheels or tines

engaged. Make certain the unit is stopped

completely before changing the gear

selection.

IMPORTANT: Use the reverse tine drive when

tilling virgin ground, sod or hard soil. Use the forward

tine drive when cultivating or tilling soft ground.

4. Squeeze the clutch control bail against the handle

to engage the wheels and tines.

NOTE: Make certain the gear selection indicator is

correctly positioned before engaging the clutch handle.

If it is between gears, the engine will stall.

Figure 7

To transport tiller, do not engage the tines. Select the

wheel drive only.

WARNING: Do not push down on the

handles so that the wheels are lifted off

the ground while using the reverse tine

drive, or the tiller could move backward

and cause personal injury.

For best results, it is recommended the garden be tilled

twice (lengthwise, then widthwise) to pulverize the soil.

Use This

Position

First Time

Transport Position

1”

3”

5”

7”

Clevis Pin

Use This Hole For

Lowest (shallowest)

Position

Use This Hole For

Highest (Deepest)

Position

Side Shields

SECTION 7: ADJUSTMENTS

WARNING: Never attempt to make any

adjustments while the engine is running,

except where specified in operator’s

manual.

HANDLE ADJUSTMENT

The handle height may be adjusted. Refer to the

Control section for details of handle adjustment.

BELT TENSION ADJUSTMENT

Periodic adjustment of the belt tension may be

required due to normal stretch and wear on the belt.

Adjustment is needed if the tines or wheels seem to

hesitate while turning, but the engine maintains the

same speed.

To adjust the tension on the belt, refer to clutch

adjustment information in “Checking the Clutch

Adjustment” section of the Assembly Instructions.

After belt tension has been adjusted, if the belt is

excessively stretched, you may need to adjust the idler

pulley rod. This can easily be checked.

With the engine off and the clutch control bail

disengaged, shift the gear selection handle to each

forward mode. If the indicator bracket touches the idler

pulley rod, (with the clutch control bail disengaged),

then an adjustment is necessary.

1. Disconnect and ground out spark plug wire against

the engine.

2. Remove the belt cover as described in the belt

replacement section on page 12.

3. Remove the hairpin clip and flat washer from the

idler pulley rod. See Figure 9.

4. Move the idler pulley rod to the lower hole in the

idler bracket. See Figure 9.

5. Replace the wave washer and hairpin clip.

6. Check clearance of the idler pulley rod to the

indicator bracket by shifting to each forward mode,

as before.

CARBURETOR ADJUSTMENT

WARNING: If any adjustments are made

to the engine while the engine is running,

(e.g. carburetor), disengage all clutches

and tines. Keep clear of all moving parts.

Be careful of heated surfaces and muffler.

Never make unnecessary adjustments. The factory

settings are correct for most applications. If

adjustments are needed, refer to the separate engine

manual packed with your tiller.

SECTION 8: LUBRICATION

Transmission—The transmission is pre-lubricated

and sealed at the factory. It requires no checking

unless the transmission is disassembled. To fill with

grease, lay the right half of the transmission on its

side. Add 30 ounces of Benalene 920 grease. Apply a

bead of RTV or silicone sealant to the right half of the

transmission, all the way around the gear

compartment. Assemble the left half to it. This grease

can be obtained at your nearest authorized dealer.

Order part number 737-0300.

Clutch Bail—Lubricate the pivot point on the clutch

bail and the cable at least once a season with light oil.

The control must operate freely in both directions.

Pivot Points—Lubricate all pivot points and linkages

at least once a season with light oil.

Tine Shaft—Remove tines at least once a season and

lubricate with oil.

Wheel Axle—Remove the wheel assemblies at least

once a season and lubricate with oil.

SECTION 9: MAINTENANCE

WARNING: Disconnect the spark plug

wire and ground it against the engine

before performing any repairs or

maintenance.

ENGINE

Refer to the separate engine manual for engine

maintenance instructions.

Maintain engine oil as instructed in the separate

engine manual packed with your unit. Read and follow

instructions carefully.

Service air cleaner every ten hours under normal

conditions. Clean every hour under extremely dusty

conditions. Poor engine performance and flooding

usually indicates that the air cleaner should be

serviced. To service the air cleaner, refer to the

separate engine manual packed with your unit.

IMPORTANT: Never run your engine without air

cleaner completely assembled.

The spark plug should be cleaned and the gap reset

every 25 hours of engine operation. Spark plug

replacement is recommended at the start of each tiller

season; check engine manual for correct plug type and

gap specification.

Clean the engine regularly with a cloth or brush. Keep

the cooling system (blower housing area) clean to

permit proper air circulation which is essential to

engine performance and life. Be certain to remove all

dirt and combustible debris from muffler area.

CLEANING THE TINE AREA

Clean the underside of the tine shield after each use.

The dirt washes off the tines easier if washed off

immediately instead of after it dries. Always towel dry

the tiller afterwards and apply a light coat of oil or

silicone to prevent rusting or water damage.

IMPORTANT: Never use a "pressure washer" to

clean your tiller. Water can penetrate tight areas of the

tiller and its chain case and cause serious damage to

the unit.

BELT REPLACEMENT

Your tiller has been engineered with a belt made of

special material (Kevlar Tensile) for longer life and

better performance. It should not be replaced with an

off-the-shelf belt.

If belt replacement is required, order belt or belts by

part number from your nearest authorized dealer.

Part No. 754-0434—‘‘V’’ Belt

1. Disconnect and ground the spark plug wire against

the engine.

2. Remove the belt cover from the left side of the

tiller as follows: See Figure 8. Remove two torx

screws from the top of belt cover.

3. Remove the hex cap nut and flat washer from the

side of the belt cover. Remove the hex screw at the

bottom of the front of the cover.

4. Remove the belt keeper bracket located behind

the engine pulley by removing two hex bolts and

lock washers. See Figure 9.

5. Remove belt. Reassemble new belt, following

instructions in reverse order.

NOTE: Upon reassembly, make certain the belt is

routed over the idler pulley and inside of belt keepers

by engine pulley. See Figure 9.

Figure 8

Figure 9

TIRES

Recommended operating tire pressure is

approximately 20 p.s.i. (check sidewall of tire for tire

manufacturer’s recommended pressure). Maximum

tire pressure under any circumstances is 30 p.s.i.

Equal tire pressure should be maintained on both tires.

When installing a tire to the rim, be certain rim is clean

and free of rust. Lubricate both the tire and rim

generously. Never inflate to over 30 p.s.i. to seat

beads.

WARNING: Excessive pressure (over 30

p.s.i.) when seating beads may cause tire/

rim assembly to burst with force sufficient

to cause serious injury.

SECTION 10: OFF-SEASON STORAGE

If the tiller will not be used for a period longer than 30

days, the following steps should be taken to prepare

the tiller for storage.

1. Clean the exterior of engine and the entire tiller

thoroughly. Lubricate the tiller as described in the

lubrication instructions.

2. We do NOT recommend the use of pressure

washers to clean your unit. They may cause

damage to electric components, spindles, pulleys,

bearings or the engine. The use of pressure

washers will result in shortened life and reduced

serviceability.

Torx Screws

Belt Cover

Hex Cap Nut

Self Tap

Screw

Engine

Pulley

Belt Keeper

Idler

Brkt.

Idler

Pulley

Rod

Brkt.

3. Refer to the engine manual for correct engine

storage instructions.

4. Wipe tines with oiled rag to prevent rust.

5. Store tiller in a clean, dry area. Do not store next

to corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment

in an unventilated or metal storage shed, care

should be taken to rustproof the equipment. Using a

light oil or silicone, coat the equipment, especially

any springs, bearings and cables.

SECTION 11: TROUBLE SHOOTING GUIDE

NOTE: For repairs beyond the minor adjustments above, contact your local authorized service dealer.

Trouble Possible Cause(s) Corrective Action

Engine fails to

start

Fuel tank empty, or stale fuel.

Throttle control lever not in correct

starting position (if so equipped).

Blocked fuel line.

Dirty aircleaner.

Choke not in ON position.

Spark plug wire disconnected.

Faulty spark plug.

Engine flooded.

Fill tank with clean, fresh gasoline. Fuel will not last over

thirty days unless a fuel stabilizer is used.

Move throttle lever to start position.

Clean fuel line.

Refer to the engine manual packed with your unit.

Move switch to ON position.

Connect wire to spark plug.

Clean, adjust gap or replace.

Refer to the engine manual packed with your unit.

Engine runs

erratic

Unit running on CHOKE.

Spark plug wire loose.

Blocked fuel line or stale fuel.

Vent in gas cap plugged.

Water or dirt in fuel system.

Dirty air cleaner.

Carburetor out of adjustment.

Move choke lever to OFF position.

Connect and tighten spark plug wire.

Clean fuel line; fill tank with clean, fresh gasoline. Fuel will

not last over thirty days unless a fuel stabilizer is used.

Clear vent.

Drain fuel tank. Refill with fresh fuel.

Refer to the engine manual packed with your unit.

Engine over-

heats

Engine oil level low.

Dirty air cleaner.

Air flow restricted.

Carburetor not adjusted properly.

Fill crankcase with proper oil.

Refer to the engine manual packed with your unit.

Adjust carburetor as instructed in separate engine manual.

Tines do not

engage

Foreign object lodged in tines.

Tine clevis pin(s) missing.

Pulley and idler not in correct

adjustment.

Not shifting properly.

Control cable not adjusted properly.

Belt worn and/or stretched.

Dislodge foreign object.

Replace tine clevis pin(s).

Take unit to authorized service dealer.

Refer to Controls section of operator’s manual for proper

shifting procedures.

Adjust control cable (see assembly instructions).

Replace belt.

Tines skip over

ground

Improper rotation. Forward rotation should only be used on soil that has

already been tilled, not on virgin soil.

Wheels do not

engage

Clevis pin missing.

Tiller is not being shifted properly.

Control cable not adjusted properly.

Belt worn and/or stretched.

Replace clevis pin.

Refer to Controls section of operator’s manual for proper

shifting procedures.

Adjust control cable (see assembly instructions).

Replace belt.

REF.

NO.

N°. DE

RÉF.

PART

NO.

N° DE

PIÈCE DESCRIPTION DESCRIPTION

1 611-0020 Wheel Shaft Ass'y 33T Arbre de roue 33 dents

2 611-0021 Tine Shaft Ass'y 18T Arbre de dents - 18 dents

3 611-0128 Jack Shaft Ass'y Arbre secondaire

4 611-0129 Input Shaft Ass'y Arbre

5 617-0058 Rev. Idler Gear Ass'y 30T Engrenage 30 dents

6 617-0059 Fr. Idler Gear Ass'y 30 T Engrenage 30 dents

7 617-0060 Tine Input Sprocket Ass'y 9T Pignon - 9 dents

8 617-0061 Wheel Input Sprocket Ass'y 10T Engrenage 10 dents

9 617-0062 Gear Ass'y 11T Engrenage 11 dents

10 686-0108 RH Housing Ass'y Boîtier de transmission - droite

11 710-0376 Hex. Scr 5/16-18 x 1.00 Gr. 5 Vis à tête hex. 5/16-18 x 1,00 Qual. 5

12 710-0599 Hex Wash S-Tapp Scr 1/4-20 x .50 Vis autotaraudeuse à rondelle hex. de 1/4-20 x 0,5

13 710-0604A Self-tapping Screw 5/16-18 x .625 Vis autotaraudeuse 5/16-18 x 0,625 po

14 710-3008 Hex Bolt 5/16-18 x .75" Lg. Gr. 5 Boulon hex. 5/16-18 x 0,75 po de lg. Qual. 5

15 711-1349 Input Shaft Arbre

16 712-0378 Hex Nut 7/16-20 Écrou à six pans 7/16-20

17 712-3004A Hex Flange L-Nut 5/16-18 Gr. 5 Contre-écrou de collet hex. 5/16-18 Qual. 5

18 713-0367 #420 Chain 1/2 Pitch x 50 Links-Endless Chaîne, no 420 pas de 1/2 x 50 maillons

19 713-0484 #50 Chain 5/8 Pitch x 54 Links Chaîne no 50, 5/8 x 54 maillons

20 716-0865 Snap Ring Joint

21 717-0853 Shifting Fork Fourchette

22 717-1582 Spur Gear 44T Engrenage 44 dents

23 717-1583 Spur Gear 30T Engrenage 30 dents

24 717-1584 Spur Gear 30T Engrenage 30 dents

25 717-1585 Spur Gear 44T Engrenage 44 dents

26 717-1587 Spur Gear 44T Engrenage 44 dents

27 717-1594 Spur Gear 16T Engrenage 16 dents

28 721-0378 Seal 1.0" Shaft Joint de 1,0 diam. arbre

29 721-0379 Seal .75 Shaft Joint de 0,75 diam. arbre

31 726-0277 Taper Cap Plug Bouchon à capuchon effilé

32 732-0496 Compression Spring .50" Lg. Ressort de compression 0,50 po de lg

33 736-0163 Flat Washer 1.03 ID x 1.62 OD x .03 Rondelle plate 1,03 DI x 1,62 DE x 0,03

34 736-0351 Flat Washer .76 ID x 1.5 OD x .03 Rondelle plate 0,76 DI x 1,5 DE x 0,03

35 736-0226 Flat Washer .469 ID x .88 OD x .063 Rondelle plate 0,469 DI x 0,88 DE x 0,063

36 736-0518 Thrust Wash. .445 ID x 1.92 OD Rondelle de butée 0,445 DI x 1,92 DE

37 736-3088 Flat Washer .635" ID x 1.59 OD Rondelle plate 0,635 DI x 1,59 DE

40 738-0645 Detent Shaft 1/2" Dia. Arbre à cliquet de 1/2 po de diamètre

41 738-0648 Jack Shaft 5/8" Dia. x 2.38 Arbre secondaire 5/8" diam. x 2,38

42 738-1013 Jack Shaft .625 x 5.0 Arbre secondaire 0,625 x 5,0

43 741-0124 Ball Bearing Roulement à billes

44 741-0420 Tine Shaft Brg. 1.002 x 2.50 Roulement de l'arbre des dents - 1,002 x 2,50

45 741-0421 Wheel Brg. .752" x 2.5” Roulement 0,752 po x 2,50 po

46 741-0563 Ball Bearing w/snap ring Roulement à billes avec bague

47 741-0862 Ball Detent .250 DIA Bille de verrouillage 0,250 dia.

48 750-0258 Spacer .315" ID x .375" Lg. Entretoise 0,315 DI x 0,375 po de lg.

49 750-0570 Step Spacer Cale d'espacement

50 750-0664 Spacer .505 ID x .88 OD Entretoise 0,505 DI x 0,88 DE

51 750-0671 Spacer .75" ID x .50" Lg. Entretoise 0,75 DI x 0,50 po de lg

52 786-0171 LH Chain Case Ass'y Ensemble de carter de chaîne de gauche

53 786-0238 Gear Positioner Bracket Support

54 736-0171 Lockwasher 7/16 ID Rondelle frein 7/16 DI

55 736-0407 Cupped Washer, .45 x 1.0 x .062 Rondelle creuse 0,45 x 1,0 x 0,062 po

686-0107 Gear Case Ass'y Complete Ensemble de carter de l'engrenage complet

214-450

11.28.03

REF.

NO.

N°. DE

RÉF.

PART

NO.

N° DE

PIÈCE DESCRIPTION DESCRIPTION

1 747-1152 Shift Rod Tige de changement de vitesses

2 649-0041 Upper Handle Assembly Guidon supérieur

3 649-0034 Lower Handle Ass'y Guidon inférieur

4 710-3005 Hex Bolt 3/8-16 x 1.25 Boulon hex. 3/8-16 x 1,25

5 710-3056 Hex Bolt 5/16-18 x 3.25 Boulon hex. 5/16-18 x 3,25

6 711-0415 Clevis Pin 3/8 Dia Axe de chape 3/8 Dia.

7 712-0379 Hex Flange Nut 3/8-24 Thd. Écrou à six pans à collet de 3/8 - fil. 24

8 712-0429 Hex Ins. L-Nut 5/16-18 Gr. 5 Nylon Contre-écrou de blocage 5/16-18 Qual. 5 nylon

9 714-0147 Hairpin Goupille

10 720-0313 Grip Poignée

11 720-0210A Small "T" Knob Bouton en <<T>> (Petite)

12 720-0278A Foam Grip (2 req'd) Poignée de mousse (qté. 2)

14 726-0317 Cable Tie Attache câble

15 735-0246 Vinyl End Plug Bouchon - vinyl

16 736-0117 Flat Washer .385 ID x .62 OD x .033 Rondelle plate 0,385 DI x 0,62 DE x 0,033

17 736-0242 Cupped Washer .340 ID x .872 OD x .060 Rondelle creuse 0,340 DI x 0,872 DE x 0,060

18 738-0958 Shoulder Spacer Cale d'épaulement

19 784-0190 Handle Adj. Crank Manivelle de réglage du guidon

20 784-0191 Bracket Hex Nut Retainer Support de retenue à écrou à six pans

21 786-0120 Depth Bar Barre de profondeur d'attelage

22 747-1219 Clutch Bail Barre de commande de l'embrayage

23 786-0181 Shift Lever Rod Tige de levier de changement de vitesses

24 686-0044A Tine Shield Cover Ass'y Couvercle

25 710-0176 Hex Scr 5/16-18 x 2.75 Vis à tête hexagonale 5/16 x 2,75

26 710-3008 Hex Bolt 5/16-18 x .75" Lg. Gr. 5 Boulon hex. 5/16-18 x 0,75 po de lg. qual. 5

27 710-3097 Carriage Bolt 3/8-16 x 1.0" Lg. Boulon ordinaire 3/8-16 x 1,0 po de lg

28 712-0421 Wing Nut Écrou à oreilles

29 736-0169 L-Wash 3/8 ID Rondelle frein 3/8 DI

30 712-3004A Hex Flange L-Nut 5/16-18 Gr. 5 Contre-écrou de collet hex. 5/16-18 Qual. 5

31 726-0106 Push Cap Coiffe

32 738-0849 Hex Screw 5/16-18 x .75 Vis à tête hex. 5/16-18 x 0,75

33 747-0432 Tiller Flap Rod Tige de protecteur de dents

34 750-0885A Spacer .322 ID x .625 OD Entretoise 0,322 DI x 0,625 DE

35 786-0090 Side Shield Dispositif de protection latéral

36 786-0113 Rear Tine Shield Protecteur de dents

37 786-0176 RH Handle Brkt. Support du guidon - droite

38 786-0177 LH Handle Brkt. Support du guidon - gauche

39 786-0178 Tine Shield Bouclieur de dents

40 786-0179 Tine Shield Brkt. Support de bouclier de dents

41 786-0180 Shoulder Spacer Brkt. Support

42 686-0109 Shift Crank Ass'y Manivelle de changement de la vitesse

44 710-1017 Torx Mach. AB-Tapp Scr. 1/4 x .62" Lg. Vis torx AB 1/4 x 0,62 po de lg

46 715-0120 Spring Pin Roll 3/16 Dia. Goupille ronde à ressort de 5/16

49 784-0208C Shift Cover Couvercle

50 784-0160 Tine Adapter Ass'y 18” Adaptateur des dents 18 po

51 712-3054 Hex L-Nut 3/8-24 (Grade 5) Écrou de blocage 3/8-24 (qual. 5)

53 742-0305 13" Dia. Articulating Tine Dent d'articulation de 13 po de diamètre

54 738-0689 Shld. Scr. 1/2 Dia. x .175 Vis à épaulement 1/2 x 0,175

55 736-0208 Flat Washer .51 ID x 1.50 OD x .075 Rondelle plate 0,51 DI x 1,50 DE x 0,075

56 736-0253 Cupped Washer .505 ID x 1.00 OD x .075 Rondelle creuse 0,505 DI x 1,00 DE x 0,075

57 738-0688 Shld. Bolt 1/2" Dia. x .320 Boulon épaulée 1/2 diam. x 0,320

58 784-0205 Tine Ass'y Comp. 18” Ensemble des dents 18 po

59 714-0149B Internal Cotter Pin Goupille fendue interne

60 735-0127 Rubber Washer Rondelle en caoutchouc

61 714-0104 Int. Cotter Pin 5/16 Dia. Goupille fendue 5/16 dia.

62 710-3022 Hex Screw 3/8-16 x 2.75" Lg. Vis à tête hex 3/8-16 x 2,75 po de lg.

63 736-0204 Flat Washer .34 ID x .62 OD x .03 Rondelle plate 0,34 DI x 0,62 DE x 0,03

64 712-0431 Flanged Lock Nut 3/8-16 Gr. F Contre-écrou de collet hex. 3/8-16 Qual. F

65 736-0169 L-Wash 3/8 ID Rondelle frein 3/8 DI

66 712-3017 Hex Nut 3/8-16 Gr. 5 Écrou hex. 3/8-16 Qual. 5

67 710-0946 Truss Mach. Scr. 1/4-20 x .62" LG. Vis taraudée 1/4-20 x 0,62 po de lg

68 712-0324 Hex Ins. Locknut 1/4-20 Gr. 8 Nylon Écrou de blocage 1/4-20 Qual. 8 nylon

69 726-0273 Battery Hose Clamp Collier

70 736-3090 Flat Washer .260 x .72 x .060 Rondelle plate 0,260 x 0,72 x 0,060

214-4501

10.12.04

REF.

NO.

N°. DE

RÉF.

PART

NO.

N° DE

PIÈCE DESCRIPTION DESCRIPTION

1 686-0111 Belt Cover Brkt Ass'y Support de couvercle de la courroie

2 710-0237 Hex Screw 5/16-24 x .625 Gr. 5 Vis à tête hexagonale 5/16-24 x 0,625 Qual. 5

3 710-0412 Hex Scr 1/4-28 x .75 Vis à tête hexagonale 1/4-28 x 0,75

4 710-0502A Hex Washer Scr 3/8-16 x 1.25 Vis à chapeau à six pans 3/8-16 x 1,25 po

5 710-0152 Hex Scr 3/8-24 x 1.00 Vis à tête hexagonale 3/8-24 x 1,00

6 710-0599 Hex Wash S-Tapp Scr 1/4-20 x .50 Vis autotaraudeuse à rondelle hex. de 1/4-20 x 0,5

7 710-0723 Hex Screw 3/8-16 x 1.25 Vis à tête hexagonale 3/8-16 x 1,25

8 712-0266 Hex Cent L-Nut 3/8-16 Contre-écrou de blocage 3/8-16

10 714-0104 Int. Cotter Pin 5/16 Dia. Goupille fendue 5/16 dia.

11 736-0104 Internal L-Washer Rondelle frein interne

12 736-0119 L-Wash 5/16 ID Rondelle frein 5/16 DI

13 736-0176 Flat Washer .265 ID x .938 OD x .120 Rondelle plate 0,265 DI x 0,938 DE x 0,120

14 736-0271 Shakeproof Spring Washer Rondelle anti-vibration

15 736-0329 L-Wash 1/4 ID Rondelle frein 1/4 DI

16 736-0452 Cupped Washer .396 ID x 1.140 OD Rondelle creuse 0,396 DI x 1,140 DE

17 738-0876 Shoulder Nut 7/16-20 Écrou à épaulement 7/16-20

18 746-1117 Clutch Cable Câble de l'embrayage

19 747-1159 Idler Pulley Rod Tige de poulie tendeur

20 754-0434 Belt: 4L x 58.16" Lg. Courroie: 4L x 58,16 po de lg.

21 756-0405 Flat Idler w/flanges 3-3/4" OD Tendeur plat à brides de 3-3/4 de po de DE

22 756-0971 Inner Engine Pulley Half Moitié intérieure de la poulie motrice

23 756-0972 Outer Engine Pulley Half Moitié extérieure de la poulie motrice

24 756-1162 Input Pulley Poulie

25 786-0064A Idler Bracket Support de tendeur

26 785-0186 Belt Keeper Brkt. Support

27 786-0187 Shift Cover Brkt. Support

28 786-0193 Idler Belt Keeper Protecteur de la courroie

29 634-0238 Wheel Ass'y RH 16 x 4 x 8 Gray Ensemble de roue CD 16 x 4 x 8 gris

634-0239 Wheel Ass'y LH 16 x 4 x 8 Gray Ensemble de roue CG 16 x 4 x 8 gris

734-0808 Tire Only (16") Pneu seulement (16 po.)

30 634-0108 Rim Only Jante seulement

31 734-0255 Air Valve Soupape à air

32 711-1017 Clevis Pin Axe de chape

33 710-0805 Hex Bolt 5/16-18 x 1.50" Lg. Gr. 5 Boulon hexagonal 5/16-18 x 1,50 po de lg Qual. 5

34 710-0382 Hex Bolt 1/2-13 x 5.00" Lg. Vis à tête hex. 1/2-13 x 5,00

35 712-0206 Hex Nut 1/2-13 Écrou hexagonal 1/2-13

36 723-0381 Counterweight 40 Lbs. Contre poids 40 lbs.

37 736-0326 Flat Washer .510 ID x 1.00 OD x .125 Rondelle plate 0,510 DI x 1,00 DE x 0,125

38 736-0921 L-Washer 1/2" ID Rondelle frein 1/2 DI

39 710-0653 Hex Wash HD Tapp Scr 1/4-20 x .38 Vis auto-taraudeuse hexagonale 1/4-20 x 0,38

40 710-1017 Torx Mach. AB-Tapp Scr. 1/4 x .62" Lg. Vis torx AB 1/4 x 0,62 po de lg.

41 712-0392 Hex Lock Stop Nut 1/4-28 Contre-écrou d'arrêt 1/4-28

42 736-3020 Flat Washer .266 ID x .625 OD Rondelle plate 0,266 DI x 0,625 DE

43 784-0158A Belt Cover Couvercle courroie

44 736-0242 Cupped Washer .340 ID x .872 OD x .060 Rondelle creuse 0,340 DI x 0,872 DE x 0,060

45 712-3010 Hex Nut 5/16-18 hd. Gr. 5 Écrou hexagonal 5/16-18 Qual. 5

737-0298 Oil Drain Tube Tuyau de vidange d'huile

737-0132 Pipe Cap 1/4 x 18 N.P.T. Capuchon de tuyau 1/4 x 18

215-4502

10.22.04

TWO YEAR LIMITED WARRANTY

For TWO YEARS from the date of retail purchase within Canada, MTD PRODUCTS LIMITED will, at its option, re

pair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or

workmanship.

This warranty does not cover:

1. Any part which has become inoperative due to misuse, commercial use, abuse, neglect, accident, im

proper maintenance or alteration; or

2. The unit if it has not been operated and/or maintained in accordance with the owner’s instructions fur

nished with the unit; or

3. The engine or motor or component parts thereof which carry separate warranties from their manufac

turers. Please refer to The applicable manufacturer’s warranty on these items; or

4. Batteries and normal wear parts except as noted below. Log splitter pumps, valves and cylinders or

component parts thereof are covered by a one year warranty; or

5 Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or adjustments

such as brake, clutch or deck; or

6. Normal deterioration of the exterior finish due to use or exposure.

Full Ninety Day Warranty on Battery: For ninety (90) days from the date of retail purchase, if any battery included

with this unit proves defective in material or workmanship and our testing determines the battery will not hold a

charge, MTD PRODUCTS LIMITED will replace the battery at no charge to the original purchaser.

Additional Limited Thirty Day Warranty on Battery: After ninety (90) days but within one hundred twenty (120)

days from the date of purchase, MTD PRODUCTS LIMITED will replace the defective battery, for the original pur-

chaser, for a cost of one-half (1/2) of the current retail price of the battery in effect at the date of return.

Full Sixty Day Warranty on Normal Wear Parts: Normal wear parts are defined as belts, blade adapters, blades,

grass bags, seats, tires, rider deck wheels and clutch parts (friction wheels). These parts are warranted to the origi-

nal purchaser to be free from defects in material and workmanship for a period of sixty (60) days from the date of

retail purchase.

How to Obtain Service: Warranty service is available, with proof of purchase, through your local authorized ser-

vice dealer or distributor. If you do not know the dealer or distributor in your area, please write to the Service

Department of MTD PRODUCTS LIMITED, P. O. BOX 1386, KITCHENER, Ontario, N2G 4J1. The return of a com

plete unit will not be accepted by the factory unless prior written permission has been extended by MTD

PRODUCTS LIMITED.

Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment

are the responsibility of the purchaser. Transportation charges for any part submitted for replacement under this

warranty must be paid by the purchaser unless such return is requested in writing by MTD PRODUCTS LIMITED.

Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is lim

ited in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty

provide the sole and exclusive remedy of MTD PRODUCTS LIMITED obligations arising from the sale of its prod

ucts.

MTD PRODUCTS LIMITED will not be liable for incidental or consequential loss or damage.

La page charge ...

MTD Tiller 450 Manuel utilisateur

Marque: MTD

Modèle: Tiller 450

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: MTD Tiller 450 User manual

MTD Tiller 450 Manuel utilisateur

Ce manuel convient également à

MTD Tiller 450 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents