NEC 60XM5, PX-60XM5A Manuel utilisateur

Marque: NEC

Modèle: 60XM5, PX-60XM5A

Catégorie: Téléviseurs à écran plasma

Taper: Manuel utilisateur

Ce manuel convient également à

NEC Corporation of America

PlasmaSync

™

60XM5

PX-60XM5A

Start up Guide

PlasmaSync Plasma Monitor

Start up Guide

Guide rapide

Guía de inicio

Guia de iniciação

Start up Guide

(Enhanced split screen Model)

For the operation of your plasma monitor, refer to the CD-ROM.

Contents

Important Information .................................. En-2

Installation .................................................. En-4

Ventilation Requirements for enclosure mounting ...... En-4

Creating a video wall ........................................... En-5

Cable Management..............................................En-5

Caution when placing the plasma monitor in portrait

mode .............................................................. En-6

Using the remote control ....................................... En-6

Battery Installation and Replacement ..................... En-6

Using the wired remote control mode .................... En-6

Operating Range .................................................... En-6

Part Names and Function .............................. En-7

Front View .......................................................... En-7

Rear View/ Terminal Board ................................... En-8

Remote Control .................................................... En-9

Basic Operations ......................................... En-10

POWER ............................................................ En-10

To turn the unit ON and OFF: .............................. En-10

VOLUME .......................................................... En-10

To adjust the sound volume: ................................. En-10

MUTE ............................................................... En-10

To mute the audio: ............................................... En-10

DISPLAY ............................................................ En-10

To check the settings: ........................................... En-10

DIGITAL ZOOM ................................................. En-10

AUTO ADJUST .................................................. En-10

To adjust the size or quality of the picture

automatically: .................................................... En-10

OFF TIMER ........................................................ En-10

To set the off timer: .............................................. En-10

To check the remaining time: ............................... En-10

To cancel the off timer: ........................................ En-10

OSM (On Screen Menu) Controls ................... En-11

Menu Operations ............................................... En-11

Menu Tree ......................................................... En-12

Troubleshooting .......................................... En-14

Specifications ............................................. En-15

Limited Warranty Plasma Monitors ................. En-16

User’s Manual on CD-ROM

䢇 The complete user’s manual is supplied on the CD-ROM in

PDF (Portable Document Format) and provides detailed

product and useage information for your NEC plasma monitor.

You must have Adobe Acrobat Reader™ or Adobe Reader™

in order to view and/or print the PDF files.

NOTE:

Adobe Acrobat Reader or Adobe Reader can be

downloaded from Adobe’s website.

Visit http://www.adobe.com and obtain the current version for

your OS.

䢇 Viewing the User’s Manual (PDF)

[Windows]

1. Insert the supplied CD-ROM in your computer’s CD-ROM drive.

2. A menu should be displayed automatically.

If this does not happen:

1) On the Windows desktop, double-click the [My Computer] icon.

2) Double-click the [NECPLASMA-UM] CD-ROM drive letter.

3) Double-click the “start_menu.pdf”.

3. Click your product name.

The user’s manual will be displayed on the screen.

[Macintosh]

1. Insert the supplied CD-ROM in your Macintosh’s CD-ROM drive.

2. Double-click the [NECPLASMA-UM] CD-ROM icon.

3. Double-click the “start_menu.pdf”.

The Start Menu will be shown.

4. Click your product name.

The user’s manual will be displayed on the screen.

䢇 Copying the User’s Manual (PDF) to your computer

The user’s manual on the supplied CD-ROM can be copied

onto your computer’s hard drive.

ENGLISH

Contents of the Package

䡺 Plasma monitor (⳯1)

䡺 Power cord (⳯1, 3 m/9.8 feet)

䡺 Remote control (⳯1)

䡺 AAA Batteries (⳯2, Manganese battery for remote

control)

䡺 Manuals (Start up Guide and CD-ROM)

䡺 Ferrite cores for power cord (⳯2), bands for power cord

(⳯2)

䡺 Ferrite core for remote cable (⳯2)

䡺 Cable clampers (⳯3), beads bands (⳯3)

Options

• Wall mount unit

• Ceiling mount unit

• Tilt mount unit

• Tabletop Stand

• Attachable speakers

En-2

Precautions

Please read this manual carefully before using your plasma monitor and

keep the manual handy for future reference.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER. NO USER-SERVICEABLE

PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This symbol warns the user that uninsulated voltage

within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any

kind of contact with any part inside of this unit.

This symbol alerts the user that important literature

concerning the operation and maintenance of this unit

has been included.

Therefore, it should be read carefully in order to avoid

any problems.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT’S

POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR

OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY

INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE

ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

Warnings and Safety Precaution

This plasma monitor is designed and manufactured to provide

long, trouble-free service. No maintenance other than cleaning

is required. Please see the section “Plasma monitor cleaning

procedure”.

The plasma display panel consists of fine picture

elements (cells) with more than 99.99 percent active cells. There

may be some cells that do not produce light or remain lit.

For operating safety and to avoid damage to the unit, read

carefully and observe the following instructions.

To avoid shock and fire hazards:

1. Provide adequate space for ventilation to avoid internal heat build-

up. Do not cover rear vents or install the unit in a closed cabinet or

shelves.

If you install the unit in an enclosure, make sure there is adequate

space at the top of the unit to allow hot air to rise and escape. If the

monitor becomes too hot, the overheat protector will be activated and

the monitor will be turned off. If this happens, turn off the power to the

monitor and unplug the power cord. If the room where the monitor is

installed is particularly hot, move the monitor to a cooler location, and

wait for 60 minutes to cool the monitor. If the problem persists, contact

your dealer for service.

2. Do not use this unit’s polarized plug with extension cords or outlets

unless the prongs can be completely inserted.

3. Do not expose the unit to water or moisture.

4. Avoid damage to the power cord, and do not attempt to modify the

power cord.

5. Unplug the power cord during electrical storms or if the unit will

not be used over a long period.

6. Do not open the cabinet which has potentially dangerous high voltage

components inside. If the unit is damaged in this way the warranty will

be void. Moreover, there is a serious risk of electric shock.

7. Do not attempt to service or repair the unit. The manufacturer is not

liable for any bodily harm or damage caused if unqualified persons

attempt service or open the back cover. Refer all service to authorized

Service Centers.

8. This equipment shall be connected to a MAIN outlet with a protective

earth-ground connection.

9. The outlet shall be installed near the equipment and shall be easily

accessible.

To avoid damage and prolong operating life:

1. Use only with 100 V to 240 V 50 Hz/60 Hz AC power supply. Continued

operation at line voltages greater than 100 V to 240 V AC will shorten

the life of the unit, and might even cause a fire hazard.

2. Handle the unit carefully when installing it and do not drop.

3. Set the unit away from heat, excessive dust, and direct sunlight.

4. Protect the inside of the unit from liquids and small metal objects. In

case of accident, unplug the power cord and have it serviced by an

authorized Service Center.

5. Do not hit or scratch the panel surface as this causes flaws on the surface

of the screen.

6. For correct installation and mounting it is strongly recommended to

use a trained, authorized dealer.

7. As is the case with any phosphor-based display (like a CRT monitor,

for example) light output will gradually decrease over the life of a Plasma

Display Panel.

8. To avoid sulfurization it is strongly recommended not to place the unit

in a dressing room in a public bath or hot spring bath.

9. Do not use in a moving vehicle, as the unit could drop or topple over

and cause injuries.

10. Do not place the unit on its side, upside-down or with the screen facing

up or down, to avoid combustion or electric shock.

11. To prevent a fire hazard, do not place near an open flame (such as a

lighted candle).

Plasma monitor cleaning procedure:

1. Use a soft dry cloth to clean the front panel and bezel area. Never use

solvents such as alcohol or thinner to clean these surfaces.

2. Clean plasma ventilation areas with a vacuum cleaner with a soft brush

nozzle attachment.

3. To ensure proper ventilation, cleaning of the ventilation areas must be

carried out monthly. More frequent cleaning may be necessary

depending on the environment in which the plasma monitor is installed.

Recommendations to avoid or minimize image retention:

Like all phosphor-based display devices and all other gas plasma displays,

plasma monitors can be susceptible to image retention under certain

circumstances. Certain operating conditions, such as the continuous

display of a static image over a prolonged period of time, can result in

image retention if proper precautions are not taken. To protect your

investment in this plasma monitor, please adhere to the following

guidelines and recommendations for minimizing the occurrence of image

retention:

* Always enable and use your computer’s screen saver function

during use with a computer input source.

* Display a moving image whenever possible.

* Change the position of the menu display from time to time.

* Always power down the monitor when you are finished using it.

If the plasma monitor is in long term use or continuous operation take the

following measures to reduce the likelihood of image retention:

* Lower the Brightness and Contrast levels as much as possible without

impairing image readability.

* Display an image with many colors and color gradations (i.e.

photographic or photo-realistic images).

* Create image content with minimal contrast between light and dark

areas, for example white characters on black backgrounds. Use

complementary or pastel color whenever possible.

* Avoid displaying images with few colors and distinct, sharply defined

borders between colors.

Plasma monitor driving sound

The panel of the Plasma monitor is composed of extremely fine pixels and

these pixels emit light according to received video signals. This principle

may cause you to hear a buzz or electrical hum coming from the Plasma

monitor. Also note that the rotation speed of the cooling fan motor increases

when the ambient temperature of the Plasma monitor becomes high. You

may hear the sound of the motor at that time.

Note:

The following items are not coverd by the warranty.

• Image retention

• Panel generated sound, examples: Fan motor noise, and electrical

circuit humming /glass panel buzzing.

Contact your dealer for other recommended procedures that will best

suit your particular application needs.

Important Information

En-3

Warning

Not for use in a computer room as defined in the

Standard for the Protection of Electronic Computer/

Data Processing Equipment ANSI/NFPA 75.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV

technician for help.

This Class B digital apparatus complies with

Canadian ICES-003.

CAUTION

When disposing of used batteries, please comply

with governmental regulations or environmental

public instruction’s rules that apply in your country/

area.

Disposing of your used

product

EU-wide legislation as implemented in

each Member State requires that used electrical

and electronic products carrying the mark (left)

must be disposed of separately from normal

household waste. This includes plasma monitors

and their electrical accessories. When you dispose

of such products, please follow the guidance of

your local authority and/or ask the shop where you

purchased the product.

After collecting the used products, they are reused

and recycled in a proper way. This effort will help

us reduce the wastes as well as the negative

impact to the human health and the environment

at the minimum level.

The mark on the electrical and electronic products

only applies to the current European Union

Member States.

core

Remote cable (not supplied)

To plasma monitor

WARNING

This product equipped with a three-wire grounding

(earthed) plug - a plug that has a third (grounding)

pin. This plug only fits a grounding-type power

outlet. If you are unable to insert the plug into an

outlet, contact a licensed electrician to replace the

outlet with a properly grounded one. Do not defeat

the safety purpose of the grounding plug.

Operating Environment

Operating environment temperature and humidity:

0 °C to +40 °C (+32 °F to +104 °F); less than 80

%RH (cooling vents not blocked)

Do not install this unit in a poorly ventilated area,

or in locations exposed to high humidity or direct

sunlight (or strong artificial light)

NOTE:

When you use the power cable (supplied), use the supplied

ferrite cores. Set the ferrite cores (supplied) on both ends

of the power cable (supplied), and then use the bands

(supplied) to fasten the ferrite cores (supplied) to the power

cable (supplied). If you do not this, this monitor will not

conform to mandatory FCC standards.

cable

(

lie

)

core

NOTE:

When you use a remote cable (not supplied), use the

supplied ferrite core. Wind the remote cable (not supplied)

around the ferrite core (supplied) once, and then fasten

the catch. If you do not this, this monitor will not conform

to mandatory FCC standards.

NOTE:

When you use an RGB cable (not supplied), use an RGB

cable including the ferrite core (not supplied) on both ends

of the cable. If you do not this, this monitor will not

conform to mandatory FCC standards.

CAUTION

When changing batteries, use only conventional

non-rechageable alkaline or manganese batteries

(2).

Risk of explosion if battery is replaced by an

incorrect type. Dispose of used batteries according

to the institutions.

En-4

50 mm (2")

Wall

50 mm (2")

You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:

* While it is upright. (See Drawing A)

* As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the

monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.

* Do not touch or hold the screen face when carrying the unit.

• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall

mount unit, Stand, etc.)

• For correct installation and mounting it is strongly recommended to use a trained, authorized

dealer.

Failure to follow correct mounting procedures could result in damage to the equipment or injury

to the installer.

Product warranty does not cover damage caused by improper installation.

* Use only a mounting kit or stand recommended by the manufacturer and listed as an accessory.

Drawing B

Drawing A

Ventilation Requirements for

enclosure mounting

To allow heat to disperse, leave space between surrounding

objects as shown on the diagram when installing.

Installation

CAUTION

• Install the device following the installation manual of the optional accessory.

• Install the device in a stable and level environment that is strong enough to support the weight.

• Use the specified clasps for installing.

• After installation, take appropriate measures to prevent the plasma from tipping over or falling.

• Make sure to move or install the device with more than one person(s).

En-5

Note:

1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT.

When LOOP OUT is ON, do not connect an OUTPUT signal from another unit as it may damage the other unit due to an

extraordinary load.

2. LOOP OUT can not be turned ON while signals are input to the RGB1 terminal.

3. LOOP OUT can be turned ON while signals are input to the RGB1 terminal if the POWER is switched ON.

Information

• To loop signals out to another plasma display, set the LOOP OUT to ON.

• To create a video wall, set the VIDEO WALL menu items properly.

• To connect monitors, please use a 1 m to 2 m (3.3 feet to 6.6 feet) BNC cable (any commercially available cable).

• If the image quality is poor, do not use the monitor’s out terminal. Use a distribution amplifier (any commercially

available distribution amplifier) to connect the split signals to the respective monitor INPUT terminals.

• Being used as a video wall function, maximaly 4-screen is rough-standard with lower than 1024⳯768, 60 Hz

signal.

• A distribution amplifier is particularly recommended when creating a 3⳯3 (or greater) video wall.

• When looping from plasma to plasma, a 1 m to 2 m (3.3 feet to 6.6 feet) 15 pin male D-Sub - 5BNC conversion

cable is required.

Creating a video wall

With built-in matrix display capability, you can create a (2⳯2, 3⳯3, 4⳯4, 5⳯5, 5⳯1, 1⳯5) video wall.

• Connect signal cables and remote cables as shown below.

Video signal RGB/DVD/HD signal

VIDEO

(IN/OUT)

AUDIO

DVD

/ HD

(

MONO

)

YCb/PbCr/Pr

RGB

/ DVD

/ HD

RGB

VDHD

DVI

(

Digital RGB

)

AUDIO

(

MONO

)

AUDIO

(

MONO

)

R/Cr/Pr G /Y B/Cb/Pb

RGB

IN OUT

REMOTE

EXTERNAL CONTROL

OUT

Remote

control

Remote

control

BNC connector

RCA phono plug

OUT

VIDEO Signal

VIDEO

(IN/OUT)

AUDIO

DVD

(

MONO

)

Y Cb /Pb Cr/Pr

RGB

DVD

RGB

VDHD

DVI

(

Digital RGB

)

AUDIO

(

MONO

)

AUDIO

(

MONO

)

R/Cr/Pr G /Y B /Cb/P b

RGB

IN OUT

REMOTE

EXTERNAL CONTROL

BNC connector

RGB signal/

DVD/HD signal

OUT

Remote

control

RGB signal/

DVD/HD signal

Remote

control

Cable Management

Using the cable clampers and beads bands provided with

the plasma display; Bundle the signal and audio cables at

the back of the unit to connect to the display.

Back of the unit

mounting holes

To attach

Insert q into a mounting hole, then

snap w into the back of q to fix the

clamper.

Clampers are designed to be difficult

to undo once in place. Please attach

carefully. Cables can be routed to the

right or left.

To detach

Using pliers, twist the clamper 90° and

pull it outward. In some cases the

clamper may have deteriorated over

time and may get damaged when

removed.

Bunch separated cables together and

secure them with the provided beads

bands.

Do not allow excessive stress to be

placed on the ends of cables.

En-6

MENU/ENTER

INPUT SELECT

DOWN UP LEFT/

RIGHT/

/EXIT

VOLUME

MENU/ENTER

INPUT SELECT

DOWN UP LEFT/

RIGHT/

/EXIT

VOLUME

Top side

Bottom side

90°

: RGB

: AUTO

: 1080B

: OFF

1024ⴒ768

EXIT

SEL.

RETURN

MENU/ENTER

OPTION1

OSM

BNC INPUT

D-SUB INPUT

RGB SELECT

HD SELECT

INPUT SKIP

ALL RESET

Caution when placing the plasma monitor in portrait mode

• Use the optional mount. Contact your store to purchase before installing.

• Rotate 90° clockwise as seen from the front when installing.

• After installing, make sure the NEC logo is located at the

left hand side of the screen when facing the plasma from

the front.

• Be sure to set “OSM ANGLE” to “V” when using.

* Failure to heed the above cautions may lead to malfunction.

Using the remote control

Battery Installation and Replacement

Designated batteries:

Please use size AAA (R03) or AAA (LR03).

Insert the 2 “AAA” batteries, making sure to set them in

with the proper polarity.

1.Press and open the cover.

2.Align the batteries according to the and

indication inside the case.

3.Replace the cover.

* The 1/8 Stereo Mini cable must be purchased separately.

OUT

REMOTE

EXTERNAL CONTROL

Remote Control

Cable*

To Remote Jack

Operating Range

* Use the remote control within a distance of about 7 m/ 23

ft. from the front of the monitor’s remote control sensor

and at horizontal and vertical angles of up to approximately

30°.

* The remote control operation may not function if the

monitor’s remote control sensor is exposed to direct

sunlight or strong artificial light, or if there is an obstacle

between the sensor and the remote control.

Using the wired remote control mode

Connect the remote cable* to the remote control’s remote

jack and the “REMOTE IN” terminal on the monitor.

When the cable is connected, the mode automatically

switches to wired remote control. When the wired remote

control mode is used, the remote control can be operated

even if no batteries are loaded.

Approx.

7 m/23 ft

CAUTION

• Use only the specified batteries.

• Make sure to insert the batteries correctly according

to the indications of and .

• Do not drop or mishandle the remote control.

• Do not get the remote control wet. If the remote

control gets wet, wipe it dry immediately.

• Avoid heat and humidity.

• When not using the remote control for a long period,

remove the batteries.

• Do not use new and old batteries together, or use

different types together.

• Do not take apart the batteries, heat them, or throw

them into a fire.

• When using the remote control in the wireless

condition, be sure to unplug the remote cable from

the REMOTE IN terminal on the monitor.

En-7

q Power

Turns the monitor’s power on and off.

w Remote sensor window

Receives the signals from the remote control.

e POWER/STANDBY indicator

When the power is on ............................. Lights green.

When the power is in the standby mode ... Lights red.

r INPUT SELECT / EXIT

Switches the input.

Functions as the EXIT buttons in the On-Screen Menu

(OSM) mode.

Front View

MENU/ENTER

INPUT SELECT

DOWN UP LEFT/

RIGHT/

/EXIT

VOLUME

MENU/ ENTER

INPUT SELECT

DOWN UP LEFT/

RIGHT/

/ EXIT

VOLUME

t LEFT/– and RIGHT/+

Functions as the CURSOR (





) buttons and used

to adjust the picture parameters in the On-Screen Menu

(OSM) mode.

y VOLUME DOWN and UP

Adjusts the volume.

Functions as the CURSOR (▲/▼) buttons in the On-

Screen Menu (OSM) mode.

u MENU/ENTER

Sets the On-Screen Menu (OSM) mode and displays

the main menu.

WARNING

The Power on/off switch does not completely

disconnect power from the display.

Part Names and Function

En-8

VIDEO

(IN/OUT)

AUDIO

DVD

/ HD

(

MONO

)

Y Cb/Pb Cr/Pr

RGB

/ DVD

/ HD

RGB

VDHD

DVI

(

Digital RGB

)

AUDIO

(

MONO

)

AUDIO

(

MONO

)

R/Cr/Pr G/Y B/ Cb/ Pb

RGB

IN OUT

REMOTE

EXTERNAL CONTROL

VIDEO

(IN/OUT)

AUDIO

DVD

/ HD

YL/R L/RCb/Pb Cr/Pr

RGB

/ DVD

/ HD

RGB

VD L/RHD

DVI

AUDIO

R/Cr/Pr G/Y B/C b/Pb

RGB

EXTERNAL CONTROL

IN OUT

REMOTE

CE F GHIJK

A AC IN

Connect the included power cord here.

B EXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the

(positive) speaker wire to the

EXT SPEAKER terminal and the (negative)

speaker wire to the

EXT SPEAKER terminal on

both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

C VIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here.

VIDEO1 can be used for Input or Output.

D AUDIO1, AUDIO2, AUDIO3

These are audio input terminals.

The input is selectable. Set which video image

corresponds to the audio input from the audio menu

screen.

E DVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc.

here.

F RGB2/ DVD2/ HD2

RGB2: You can connect an analog RGB signal

and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High

Definition sources, Laser Discs, etc.

here.

This input can be set for use with an

RGB or component source.

G RGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output.

H RGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a

DVI output.

This input can be set for use with an RGB3.

I EXTERNAL CONTROL

This terminal is used when operating and controlling

the monitor externally with a control system (by RS-

232C).

J REMOTE IN

Connect the remote cable to the remote control’s

remote jack to obtain wired remote control.

K REMOTE OUT

Connect the remote cable to the REMOTE IN jack of

the other display monitor to obtain wired remote

control.

L Handles

Use when installing or carrying the plasma monitor.

Rear View/ Terminal Board

En-9

q POWER ON/STANDBY

Switches the power on/standby.

(This does not operate when the POWER/STANDBY

indicator of the plasma is off.)

w RGB/PC

Press this button to select RGB/PC as the source.

RGB/PC can also be selected using the INPUT

SELECT button on the monitor.

e DVD / HD

Press this button to select DVD/HD as the source.

DVD/HD can also be selected using the INPUT

SELECT button on the monitor.

r VIDEO

Press this button to select VIDEO as the source.

VIDEO can also be selected using the INPUT SELECT

button on the monitor.

t MENU/ENTER

Press this button to access the OSM controls.

Press this button during the display of the main menu

to go to the sub menu.

y CURSOR (▲ / ▼ /





)

Use these buttons to select items or settings and to

adjust settings or switch the display patterns.

u EXIT

Press this button to exit the OSM controls in the main

menu. Press this button during the display of the sub

menu to return to the previous menu.

i POINTER

Press this button to display the pointer.

o ZOOM (+ /–)

Enlarges or reduces the image.

!0 VOLUME (+ /–)

Adjusts the audio volume.

!1 MUTE

Mutes the audio.

!2 WIDE

Press this button to select and switch the screen sizes.

WIDE button is not active for all signals.

!3 DISPLAY

Displays the source settings on the screen.

!4 OFF TIMER

Activates the off timer for the unit.

!5 SIDE BY SIDE

Press this button to show a couple of pictures in the

side-by-side mode.

!6 PICTURE IN PICTURE

Press this button to show a couple of pictures in the

picture-in-picture mode.

!7 SINGLE

Cancels the split screen mode.

!8 SELECT/FREEZE

Press this button to select the active picture in a split

screen mode.

When the PIC FREEZE function is operating, this button

can be used to display still images on the sub screen.

!9 AUTO ADJUST

Press this button to adjust Fine Picture, Picture ADJ,

Position, and Contrast automatically. Press this button

in video mode and the Auto Adjust switches to ZOOM

mode automatically when a letter box image is

displayed.

@0 ID SELECT

Set the ID number in the remote control. The remote

control can then be used only for a display with the

same ID number. When several displays are used

together they can be controlled individually.

@1 CLEAR/SEAMLESS SW

Clears the number set by the ID SELECT button.

When the SEAMLESS SW function is operating, this

button can be used to switch the input source quickly.

@2 Remote control signal transmitter

Transmits the remote control signals.

@3 Remote Jack

Insert the plug of the remote cable (The 1/8 Stereo

Mini cable) here when using the supplied remote

control in the wired condition.

Remote Control

→ VIDEO1 → VIDEO2 → VIDEO3

En-10

Basic Operations

POWER

To turn the unit ON and OFF:

1. Plug the power cord into an active AC power outlet.

2. Press the Power button (on the unit).

The monitor’s POWER/STANDBY indicator turns red

and the standby mode is set.

3. Press the POWER ON button (on the remote control) to

turn on the unit.

The monitor’s POWER/STANDBY indicator will light

up (green) when the unit is on.

Press the POWER STANDBY button (on the remote control)

or the Power button (on the unit) to turn off the unit.

The monitor’s POWER/STANDBY indicator turns red

and the standby mode is set (only when turning off the

unit with the remote control).

VOLUME

To adjust the sound volume:

1. Press and hold the VOLUME button (on the remote

control or the unit) to increase to the desired level.

2. Press and hold the VOLUME

button (on the remote

control or the unit) to decrease to the desired level.

MUTE

To mute the audio:

Press the MUTE button on the remote control to mute the

audio; press again to restore.

DISPLAY

To check the settings:

1. Press the DISPLAY button to display the display mode.

2. If the button is not pressed for approximately three seconds,

the menu turns off.

DIGITAL ZOOM

Digital zoom specifies the picture position and enlarges

the picture.

1. (Be sure ZOOM NAV is off.)

Press the POINTER button to display the pointer. (

)

To change the size of the picture:

Press the ZOOM+ button and enlarge the picture.

The pointer will change to resemble a magnifying glass.

(

)

A press of the ZOOM- button will reduce the picture

and return it to its original size.

To change the picture position:

Select the position with the ▲▼





buttons.

2. Press the POINTER button to delete the pointer.

AUTO ADJUST

To adjust the size or quality of the picture

automatically:

Press the AUTO ADJUST button.

Information

 AUTO ADJUST ON setting

When RGB (still picture) input is selected:

Fine Picture, Picture ADJ, Position, and Contrast will

be adjusted automatically.

When RGB (motion picture), VIDEO, or Y/Pb/Pr

(component) input is selected:

The screen size switches to ZOOM mode automatically

when a letter box image is displayed.

OFF TIMER

To set the off timer:

The off timer can be set to turn the power off after 30, 60,

90 or 120 minutes.

1. Press the OFF TIMER button to start the timer at 30

minutes.

2. Press the OFF TIMER button to the desired time.

3. The timer starts when the menu turns off.

→ 30 → 60 → 90 → 120 → 0

OFF TIMER 30

To check the remaining time:

1. Once the off timer has been set, press the OFF TIMER

button once.

2. The remaining time is displayed, then turns off after a few

seconds.

3. When five minutes remain the remaining time appears

until it reaches zero.

OFF TIMER 28

To cancel the off timer:

1. Press the OFF TIMER button twice in a row.

2. The off timer is canceled.

OFF TIMER 0

Note:

After the power is turned off with the off timer ...

A slight current is still supplied to the monitor. When you

are leaving the room or do not plan to use the system for a

long period of time, turn off the power to the monitor.

En-11

Menu Operations

The OSM window is displayed with respect to the

screen as shown on the diagram.

* Depending on the screen’s mode, the OSM may be

displayed differently.

In the explanation, the OSM section is shown close up.

SEL.

MAIN MENU 1 / 2

PICTURE

AUDIO

IMAGE ADJUST

OPTION1

ADVANCED OSM

: OFF

EXIT

MENU/ENTER

EXIT

The following describes how to use the menus and the

selected items.

1. Press the MENU/ENTER button on the remote control to

display the MAIN MENU.

SEL.

MAIN MENU 1 / 2

PICTURE

AUDIO

IMAGE ADJUST

OPTION 1

ADVANCED OSM

: OFF

EXIT

MENU/ENTER

EXIT

SEL.

MAIN MENU 2 / 2

LANGUAGE

COLOR SYSTEM

SOURCE INFORMATION

EXIT

MENU/ENTER

EXIT

2. Press the cursor buttons ▲ ▼ on the remote control to

highlight the menu you wish to enter.

3. Press the MENU/ENTER button on the remote control to

select a sub menu or item.

SEL. ADJ. RETURN

PICTURE 1 / 2

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

PICTURE MODE

: NORMAL

: OFF

: 52

: 32

: 16

: 32

EXIT

4. Adjust the level or change the setting of the selected item

by using the cursor buttons





on the remote control.

5. The adjustments or settings are then stored in memory.

The change is stored until another change is made.

6. Repeat steps 2 – 5 to adjust an additional item, or press

the EXIT button on the remote control to return to the

main menu.

* When adjusting using the bar at the bottom of the screen,

press the





button within 5 seconds. If not, the

current setting is stored and the previous screen appears.

Note:

The main menu disappears by pressing the EXIT

button.

Information

 Advanced menu mode

When “ADVANCED OSM” is set to “ON” in the main

menu (1/2), full menu items will be shown.

SEL.

MAIN MENU 1 / 2

PICTURE

AUDIO

IMAGE ADJUST

OPTION1

OPTION2

OPTION3

OPTION4

ADVANCED OSM

: ON

EXIT

MENU/ENTER

EXIT

* The actual screen may be different from the ones in

this manual.

OSM (On Screen Menu) Controls

En-12

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

PICTURE CONTRAST ←→ 0←52→72 YES YES En-21

BRIGHTNESS ←→ 0←32→64 YES YES En-21

SHARPNESS ←→ 0←16→32 YES YES En-21

COLOR ←→ 0←32→64 YES YES En-21

TINT R←→G 0←32→64 YES YES En-21

PICTURE MODE BRIGHT/NORMAL/THEAT.1/THEAT.2/DEFAULT YES YES En-21

NR OFF/NR-1/NR-2/NR-3 YES YES En-21

COLOR TEMP. LOW/MID LOW/MID/HIGH YES YES En-21

WHITE BALANCE GAIN RED ←→  0←40→70 YES NO En-22

GAIN GREEN ←→ 0←40→70 YES NO En-22

GAIN BLUE ←→ 0←40→70 YES NO En-22

BIAS RED ←→ 0←40→70 YES NO En-22

BIAS GREEN ←→ 0←40→70 YES NO En-22

BIAS BLUE ←→ 0←40→70 YES NO En-22

RESET OFF←→ON YES NO En-22

GAMMA 1←→2←

…

→4 YES NO En-22

LOW TONE *

MODE1←→MODE2 YES NO En-22

COLOR TUNE RED Y←→M0←32→64 YES NO En-22

GREEN C←→Y0←32→64 YES NO En-22

BLUE M←→C0←32→64 YES NO En-22

YELLOW G←→R0←32→64 YES NO En-22

MAGENTA R←→B0←32→64 YES NO En-22

CYAN B←→G0←32→64 YES NO En-22

RESET OFF←→ON YES NO En-22

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

AUDIO BASS ←→ 0←13→26 YES YES En-23

TREBLE ←→ 0←13→26 YES YES En-23

BALANCE L←→R -22←0→+22 YES YES En-23

AUDIO INPUT1 VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES YES En-23

AUDIO INPUT2 VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES YES En-23

AUDIO INPUT3 VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES YES En-23

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

IMAGE ADJUST ASPECT MODE NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9/UNDERSCAN/TRUE*

— YES En-23

V-POSITION ←→ -64←0→+64 YES YES En-23

H-POSITION ←→ -128←0→+127 YES YES En-23

V-HEIGHT ←→ 0←→64 YES YES En-23

H-WIDTH ←→ 0←→64 YES YES En-23

AUTO PICTURE OFF←→ON*

NO YES En-23

FINE PICTURE*

←→*

0←→64 YES YES En-23

PICTURE ADJ.*

←→*

0←→64 YES YES En-23

UNDERSCAN OFF←→ON YES NO En-23

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

OPTION1 OSM DISPLAY OSM OFF←→ON YES YES En-24

OSM ADJ. 1←

…

→6 YES YES En-24

OSM ANGLE H←→V YES YES En-24

OSM ORBITER OFF←→ON YES YES En-24

OSM CONTRAST LOW←→NORMAL YES YES En-24

BNC INPUT RGB←→COMP. YES YES En-24

D-SUB INPUT RGB — YES En-24

RGB SELECT AUTO YES YES En-24

HD SELECT 1080B/1035I/1080A NO YES En-25

INPUT SKIP OFF←→ON YES YES En-25

ALL RESET OFF←→ON — YES En-25

:Shaded areas indicate the default value.

←→

: Press the





button to adjust.

:Menu items in a ruled box are available when the ADVANCED OSM is set to ON.

Menu Tree

* For further details of each menu item, please refer to the CD-ROM.

En-13

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

OPTION2 PWR. MGT. OFF←→ON YES NO En-26

CINEMA MODE OFF←→ ON YES NO En-26

LONG LIFE PLE AUTO/LOCK 1/LOCK 2/LOCK 3 YES NO En-26

ORBITER AUTO 1 YES NO En-27

AUTO 2 YES NO En-27

MANUAL H-DOT/V-LINE/TIME YES NO En-27

OFF YES NO En-27

INVERSE OFF YES NO En-27

ON WORKING TIME/WAITING TIME YES NO En-27

WHITE YES NO En-27

SCREEN WIPER OFF YES NO En-28

ON WORKING TIME/WAITING TIME/SPEED YES NO En-28

SOFT FOCUS OFF/1/2/3/4 YES NO En-28

GRAY LEVEL 0←

…

→3←

…

→15 YES NO En-28

S1/S2 AUTO←→OFF YES NO En-29

PICTURE SIZE*

OFF←→ON YES NO En-29

DVI SET UP PLUG/PLAY PC←→STB/DVD NO NO En-29

BLACK LEVEL LOW←→HIGH NO NO En-29

PROTOCOL SET OFF←→ON YES NO En-29

CLOSECAPTION OFF←→CC1~4←→TEXT1~4 YES NO En-30

CAPTION CONT LOW←→NORMAL YES NO En-30

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

OPTION3 TIMER PRESENT TIME

DAYLIGHT SAVING TIME

OFF←→ON NO NO En-30

DAY/HOUR/MINUTES NO NO En-30

TIMER OFF YES NO En-31

PROGRAM DAY/ON/OFF(HOUR, MINUTES)/INPUT/FUNC. YES NO En-31

REPEAT SINGLE/MULTI/VIDEO-W YES NO En-31

PWR. ON MODE INPUT LAST /MULTI/ VIDEO 1-3 / DVD/HD 1-2 / RGB 1-3 YES NO En-32

VOLUME LAST←→0←

…

→42 YES NO En-32

CONTROL LOCK OFF←→ON YES NO En-32

IR REMOTE OFF←→ON YES NO En-33

LOOP OUT OFF←→ON YES NO En-33

REMOTE ID ALL←→1←

…

→4 NO NO En-33

ID NUMBER ALL←→1←

…

→256 YES NO En-33

VIDEO WALL DIVIDER OFF/1/22/33/44/55/51/15 YES NO En-34

POSITION

No.1←

…

→No.4/No.7←

…

→No.15/No.16←

…

→No.31/No.32←

…

→No.56

— NO En-34

DISP. MODE SPLIT←→BLANK YES NO En-34

AUTO ID OFF←→ON YES NO En-34

IMAGE ADJUST ASPECT MODE

NORMAL/FULL/STADIUM/ZOOM/2.35:1/14:9/UNDERSCAN/TRUE

— NO En-35

V-POSITION/H-POSITION/V-HEIGHT/H-WIDTH/AUTO PICTURE/

FINE PICTURE*

/PICTURE ADJ.*

/UNDERSCAN

P. ON DELAY OFF/ON/MODE1/MODE2 YES NO En-35

PLE LINK OFF←→ON YES NO En-35

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

OPTION4 SUB. PICTURE SUB. P DETECT OFF←→AUTO YES NO En-36

SUB. P RATE 20%←

…

→100% YES NO En-36

DISPLAY FADE←→NORMAL YES NO En-36

ZOOM NAV OFF←→S BY S←→BTM LFT←→BTM RGT←→TOP RGT←→TOP LFT YES NO En-36

PIC FREEZE OFF←→S BY S1←→S BY S2←→BTM LFT←→BTM RGT←→TOP RGT←→TOP LFT YES NO En-36

SEAMLESS SW OFF YES NO En-37

ON SELECT1/SELECT2 YES NO En-37

TEXT INSERT OFF/BOTTOM-1/BOTTOM-2/BOTTOM-3/MID. LOW/MID. HIGH/TOP-3/TOP-2/TOP-1/LEFT/RIGHT YES NO En-37

INPUT/SUB. P DETECT/PIC. RATE/DISPLAY YES NO En-37

Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET OSM ANGLE “V” REFERENCE

ADVANCED OSM OFF←→ON YES NO En-38

LANGUAGE ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/У/PORTUGUÊS NO NO En-38

COLOR SYSTEM AUTO/3.58 NTSC/4.43 NTSC/PAL/PAL 60/PAL-N/PAL-M/SECAM NO YES En-38

SOURCE INFORMATION

— — YES En-38

*1 Only when AUTO PICTURE is OFF.

*2 RGB only.

*3 “PICTURE SIZE” and “TRUE” are only for 50 and 60 inch types.

*4 “LOW TONE” is only for 50 inch type.

Information

 Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

En-14

Troubleshooting

Remedy

• If there are no abnormalities in the image and sound,

the noise is caused by the cabinet reacting to

changes in temperature. This will not affect

performance.

• Leave some space between the display and the

connected components.

• Replace both batteries with new ones.

• Set IR REMOTE OFF on OPTION3 menu.

• Set an ID number with the ID SELECT button, or set

the ID number to ALL.

• Plug the monitor’s power cord into a power outlet.

• Press the power button on the monitor to turn on the

power.

• Replace both batteries with new ones.

• Set IR REMOTE ON.

• Set an ID number with the ID SELECT button, or set

the ID number to ALL.

• Point the remote control at the monitor’s remote

control sensor when pressing buttons, or remove the

obstacle.

• Eliminate the light by closing curtains, pointing the

light in a different direction, etc.

• Replace both batteries with new ones.

• Unplug the remote cable from the monitor.

• Set the Control Lock to OFF.

• Plug the monitor’s power cord into a power outlet.

• Increase the volume.

• Press the remote control’s MUTE button.

• Connect the speakers properly.

• Set AUDIO INPUT on the AUDIO menu correctly.

• Adjust picture control as needed.

Try another location for the monitor.

Be sure all connections are secure.

• Adjust picture controls as needed.

Check pin assignments and connections.

• Adjust the tint and color (under PICTURE).

• Turn on the computer’s power.

• Connect source to the monitor.

• Operate the computer (move the mouse, etc.).

• Set LOOP OUT OFF.

• Adjust the IMAGE ADJUST properly.

• Press the WIDE button on the remote control and

adjust properly.

• Set to the proper resolution.

• Check the input signal.

• Promptly switch off the power of the main unit and

wait until the internal temperature drops. See*1.

• Prompty switch off the power of the main unit. See

*2.

If the picture quality is poor or there is some other problem, check the adjustments, operations, etc., before requesting service.

Symptom

The unit emits a crackling sound.

Picture is disturbed.

Sound is noisy.

Remote control operates erroneously.

The remote control does not work.

Monitor’s power does not turn on when the

remote control’s power button is pressed.

Monitor does not operate when the remote

control’s buttons are pressed.

The front panel buttons of the main unit do

not function.

No sound or picture is produced.

Picture appears but no sound is produced.

Poor picture with VIDEO signal input.

Poor picture with RGB signal input.

Tint is poor or colors are weak.

Nothing appears on screen.

Part of picture is cut off or picture is not

centered.

Image is too large or too small.

Picture is unstable.

POWER/STANDBY indicator is lighted in red.

POWER/STANDBY indicator is blinking in

red.

POWER/STANDBY indicator is blinking in

green and red, or green.

Checks

• Are the image and sound normal?

• Is a connected component set directly in front or at

the side of the display?

• Are the remote control’s batteries worn out?

• Is IR REMOTE set to ON?

• Has an ID number been set for the main unit?

• Is the monitor’s power cord plugged into a power

outlet?

• Are all the monitor’s indicators off?

• Are the remote control’s batteries worn out?

• Is IR REMOTE set to OFF?

• Has an ID number been set for the main unit?

• Is the remote control pointed at the monitor, or is

there an obstacle between the remote control and

the monitor?

• Is direct sunlight or strong artificial light shining on

the monitor’s remote control sensor?

•

Are the remote control’s batteries worn out?

• The remote cable is plugged into the REMOTE IN

terminal (Wired).

• The front panel buttons do not function during

Control Lock.

• Is the monitor’s power cord plugged into a power

outlet?

• Is the volume set at the minimum?

• Is the mute mode set?

• Are the speakers properly connected?

• Is AUDIO INPUT set correctly?

• Improper control setting.

Local interference.

Cable interconnections.

Input impedance is not correct level.

• Improper control setting.

Incorrect 15 PIN connector pin connections.

• Are the tint and colors properly adjusted?

• Is the computer’s power turned on?

• Is a source connected?

• Is the power management function in the standby

or off mode?

• Is LOOP OUT set to ON?

• Is the position adjustment appropriate?

• Is the screen size adjustment appropriate?

• Is the computer’s resolution setting appropriate?

• Horizontal and / or vertical sync signal is not

present when the Intelligent Power Manager

control is on.

• The temperature inside the main unit has become

too high and has activated the protector.

——————

*1 Overheat protector

If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor

and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location and wait for the monitor

to cool for 60 minutes. If the problem persists, contact your dealer.

*2 In the following case, power off the monitor immediately and contact your dealer or authorized Service Center.

The monitor turns off 5 seconds after powering on and then the POWER/STANDBY indicator blinks. It indicates that the power supply circuit, plasma

display panel, temperature sensor, or one or more fans have been damaged.

En-15

Specifications

Screen Size 51.9 inches(H)⳯29.2 inches(V)

1319 mm(H)⳯742 mm(V)

diagonal 60 inches

Aspect Ratio 16 : 9

Resolution 1365 pixels(H)⳯768 pixels(V)

Pixel Pitch 0.038 inches(H)⳯0.038 inches(V)

0.97 mm(H)⳯0.97 mm(V)

Signals

Synchronization Range Horizontal : 15.5 kHz to 110.0 kHz

(automatic : step scan)

Vertical : 50.0 Hz to 120.0 Hz

(automatic : step scan)

Input Signals RGB, NTSC (3.58/4.43), PAL (B,G,M,N),

PAL60, SECAM, HD*

, DVD*

, DTV*

Input Terminals (VIDEO1 and RGB1 can also be used as OUTPUT terminals)

RGB

Visual 1 (Analog) mini D-sub 15-pin⳯1

Visual 2 (Analog) BNC (R, G, B, HD, VD)⳯1*

Visual 3 (Digital) DVI-D 24-pin⳯1*

Video

Visual 1 BNC⳯1

Visual 2 RCA-pin⳯1

Visual 3 S-Video: DIN 4-pin⳯1

DVD/HD

Visual 1 RCA-pin (Y, Cb/Pb, Cr/Pr)⳯1*

Visual 2 BNC (Y, Cb/Pb, Cr/Pr)⳯1*

Visual 3 DVI-D 24-pin⳯1*

Audio Stereo RCA⳯3 (Selectable)

External Control D-sub 9-pin⳯ 1 (RS-232C)

Remote In Mini jack⳯1

Remote Out Mini jack⳯1

Sound output 9 W+9 W at 6 ohm

Power Supply AC100 V to 240 V 50 Hz/60 Hz

Current Rating 7.0 A (maximum)

Power Consumption 440 W (typical)

Dimensions 57.9 inches(W)⳯34.7 inches(H)⳯4.8 inches(D)

1470 mm(W)⳯880 mm(H)⳯122 mm(D)

Weight 135.6 lbs / 61.5 kg (without stand)

Environmental Considerations

Operating Temperature 0 °C to 40 °C / 32 °F to 104 °F

Humidity 20 % to 80 % (no condensation)

Storage Temperature -10 °C to 50 °C / 14 °F to 122 °F

Humidity 10 % to 90 % (no condensation)

Other Features Motion compensated 3D Scan Converter (NTSC,

PAL, 480I, 576I, 525I, 625I, 1035I, 1080I), 2-3

pull down Converter (NTSC, 480I, 525I, 1035I,

1080I (60 Hz)), 2-2 pull down Converter (PAL,

576I, 625I, NTSC, 480I, 525I), Digital Zooming

(100 % to 900 % Selectable), Video Wall 4-25

multi screens, Self Diagnosis via RS232C,

Long Life Mode (PEAK BRIGHT, ORBITER,

INVERSE, WHITE, SCREEN WIPER, SOFT

FOCUS, etc.), Control Lock (Except power SW),

Input Skip, Color Tune, Programmable Timer,

Loop Throughout Interface, Plug and play

(DDC1, DDC2b, RGB3: DDC2b only), Enhanced

Split Screen, Protocol Set, etc.

Accessories Power cord (⳯1), Remote control (⳯1), AAA

batteries (⳯2), Manuals (Start up Guide and

CD-ROM), Ferrite cores for power cord (⳯2),

bands for power code (⳯2), Cable clampers

(⳯3), beads bands (⳯3), Ferrite core for

remote cable (⳯2).

Regulations UL 60950-1, CAN/CSA-C22.2 No.60950-1-03,

FCC class B, ICES-003 class B

The features and specifications may be subject to change without

notice.

HD/DVD/DTV input signals supported on this system.

480P (60 Hz) 480I (60 Hz) 525P (60 Hz)

525I (60 Hz) 576P (50 Hz) 576I (50 Hz)

625P (50 Hz) 625I (50 Hz) 720P (60 Hz)

720P (50 Hz) 1035I (60 Hz) 1080I (50 Hz)

1080I (60 Hz) 1080P (50 Hz) 1080P (60 Hz)

The 5-BNC connectors are used as RGB2 and DVD/HD2 input.

Select one of them under “BNC INPUT”.

Compatible with HDCP.

Supported Signals

• 640ⴒ480P @ 59.94/60 Hz • 1440 (720)ⴒ480I @ 59.94/60 Hz

• 720ⴒ480P @ 59.94/60 Hz • 1440 (720)ⴒ576I @ 50 Hz

• 720ⴒ576P @ 50 Hz • 1920ⴒ1080I @ 59.94/60 Hz

• 1280ⴒ720P @ 59.94/60 Hz • 1920ⴒ1080I @ 50 Hz

• 1280ⴒ720P @ 50 Hz

• 1920ⴒ1080P @ 59.94/60 Hz

• 1920ⴒ1080P @ 50 Hz

Note: In some cases a signal on the plasma monitor may not be displayed

properly. The problem may be an inconsistency with standards from

the source equipment (DVD, Set-top box, etc.). If you do experience

such a problem please contact NEC Corporation of America and also

the manufacturer of the source equipment.

Units are in inch

(mm)

1.8"

(45)

57.9" (1470)

34.7" (880)

51.9" (1319)

29.2" (742)

4.8"

(122)

3.0"

(77)

En-16

NEC Corporation of America warrants this product to be

free from defects in material and workmanship under the

following terms and, subject to the conditions set forth

below, agrees to repair or replace (at NEC Corporation of

America’ sole option) any part of the enclosed unit which

proves defective. Replacement parts or products may be

new or refurbished and will meet specifications of the

original parts or products.

HOW LONG IS THE WARRANTY?

Parts and labor are warranted for (1) one year from the

date of the first customer purchase.

WHO IS PROTECTED?

This warranty may be enforced only by the first purchaser.

WHAT IS COVERED AND WHAT IS NOT COVERED

Except as specified below, this warranty covers all defects

in material or workmanship in this product. The following

are not covered by the warranty:

1. Any product which is not distributed in the U.S.A. or Canada by

NEC Corporation of America or which is not purchased in the

U.S.A. or Canada from an authorized NEC Corporation of

America dealer.

2. Any product of which the serial number has been defaced,

modified or removed.

3. Damage, deterioration or malfunction resulting from:

a. Accident, misuse, abuse, neglect, fire, water, lightning or other

acts of nature, unauthorized product modification, or failure

to follow instructions supplied with the product.

b. Repair or attempted repair by anyone not authorized by NEC

Corporation of America.

c. Any shipment of the product (claims must be presented to the

carrier).

d. Removal or installation of the product.

e. Any other cause which does not relate to a product defect.

f. Burns or residual images upon the phosphor of the panel.

4. Cartons, carrying cases, batteries, external cabinets, magnetic

tapes, or any accessories used in connection with the product.

5. Service outside of the U.S.A. and Canada.

WHAT WE WILL PAY FOR AND WHAT WE WILL

NOT PAY FOR

We will pay labor and material expenses for covered items,

but we will not pay for the following:

1. Removal or installation charges.

2. Costs of initial technical adjustments (set-up), including

adjustment of user controls. These costs are the responsibility of

the NEC Corporation of America dealer from whom the product

was purchased.

3. Shipping charges.

HOW YOU CAN GET WARRANTY SERVICE

1. To obtain service on your product, consult the dealer from whom

you purchased the product.

2. Whenever warranty service is required, the original dated invoice

(or a copy) must be presented as proof of warranty coverage.

Please also include in any mailing your name, address and a

description of the problem(s).

3. For the name of the nearest NEC Corporation of America

authorized service center, call NEC Corporation of America at

800-836-0655.

LIMITATIONS OF LIABILITY

Except for the obligations specifically set forth in this

warranty statement, we will not be liable for any direct,

indirect, special, incidental, consequential, or other types

of damages, whether based on contract, tort, or any other

legal theory, whether or not we have been advised of the

possibility of such damages. This warranty is in lieu of all

other warranties expressed or implied, including, but not

limited to, the implied warranties of merchantability or

fitness for a particular purpose.

EXCLUSION OF DAMAGES

NEC Corporation of America’ liability for any defective

product is limited to the repair or replacement of the

product at our option. NEC Corporation of America shall

not be liable for:

1. Damage to other property caused by any defects in this

product, damages based upon inconvenience, loss of use of

the product, loss of time, commercial loss; or

2. Any other damages whether incidental, consequential or

otherwise. Some states do not allow limitation on how long

an implied warranty lasts and/or do not allow the exclusion

or limitation of incidental or consequential damages, so the

above limitations and exclusions may not apply to you.

HOW STATE LAW RELATES TO THE WARRANTY

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

FOR MORE INFORMATION,

TELEPHONE 800-836-0655

NEC CORPORATION OF AMERICA

1250 N. Arlington Heights Road, Suite 400

Itasca, Illinois 60143-1248

Note:

All products returned to NEC Corporation of

America for service MUST have prior approval. To get

approval, call NEC Corporation of America at 800-836-

0655.

Limited Warranty Plasma Monitors

Guide rapide

(Modèle à découpe d’image avancée)

Pour le fonctionnement de votre moniteur plasma, référez-vous au CD-ROM.

FRANÇAIS

Manuel d’utilisation sur CD-ROM

䢇 Le manuel d’utilisation complet est fourni sur le CD-ROM en

format PDF (Portable Document Format) et fournit des

informations détaillées concernant le produit et son utilisation

pour votre moniteur plasma NEC.

Vous devez avoir Acrobat Reader™ ou Adobe Reader ™ pour

pouvoir visionner et/ou imprimer les fichiers PDF.

REMARQUE:

Adobe Acrobat Reader ou Adobe Reader peuvent

être téléchargés sur le site d’Adobe.

Rendez-vous sur http://www.adobe.com pour obtenir la version

correspondant à votre système d’exploitation.

䢇 Visionner le manuel d’utilisation (PDF)

[Windows]

1. Insérez le CD-ROM fourni dans le lecteur de CD-ROM de votre

ordinateur.

2. Un menu doit s’afficher automatiquement.

Si ce n’est pas le cas :

1) Sur le bureau Windows, double-cliquez sur l’icône [Mon

ordinateur].

2) Double-cliquez sur la lettre du lecteur de CD-ROM

[NECPLASMA-UM].

3) Double-cliquez sur “start_menu.pdf”.

3. Cliquez sur le nom de votre produit.

Le guide de l’utilisateur s’affichera à l’écran.

[Macintosh]

1. Insérez le CD-ROM fourni dans le lecteur de CD-ROM de votre

Macintosh.

2. Double-cliquez sur l’icône du CD-ROM [NECPLASMA-UM].

3. Double-cliquez sur “start_menu.pdf”.

Le menu de départ s’affichera.

4. Cliquez sur le nom de votre produit.

Le guide de l’utilisateur s’affichera à l’écran.

䢇 Copier le manuel d’utilisation (PDF) sur votre ordinateur

Le manuel d’utilisation se trouvant sur le CD-ROM fourni peut

être copié sur le disque dur de votre ordinateur.

Table des matière

Recommandations importantes ..................... Fr-2

Installation .................................................. Fr-4

Ventilation requise pour le montage de l’ensemble.........Fr-4

Créer un mur d’images ..............................................Fr-5

Fixation des câbles ....................................................Fr-5

Faire attention lorsque le moniteur plasma est installé

verticalement .........................................................Fr-6

Comment utiliser la télécommande...............................Fr-6

Mise en place et remplacement des piles ...................... Fr-6

Utilisation du mode télécommande à câble .................. Fr-6

Distance de fonctionnement ......................................... Fr-6

Noms des composants et leur fonction ........... Fr-7

Vue de face...............................................................Fr-7

Vue arrière / Raccordements ......................................Fr-8

Télécommande ..........................................................Fr-9

Fonctions de base ....................................... Fr-10

POWER (MARCHE/ARRÊT) ......................................Fr-10

Pour mettre en marche et arrêter l’appareil :............... Fr-10

VOLUME ................................................................Fr-10

Pour régler le volume sonore : ................................... Fr-10

MUTE (SOURDINE) ..................................................Fr-10

Pour mettre le son en sourdine : ................................. Fr-10

DISPLAY (AFFICHAGE) .............................................Fr-10

Pour vérifier les réglages : .......................................... Fr-10

ZOOM NUMERIQUE ...............................................Fr-10

AUTO ADJUST (REGLAGE AUTO) ............................Fr-10

Pour régler automatiquement le format et la qualité de

l’image: ................................................................... Fr-10

OFF TIMER (ARRÊT TEMPORISÉ) ...............................Fr-10

Réglage de la temporisation de l’alimentation : .......... Fr-10

Vérification du temps restant avant l’arrêt

automatique: ............................................................ Fr-10

Annulation de la temporisation de l’alimentation: ...... Fr-10

Commandes OSM (MENUS ÉCRAN) ................. Fr-11

Opérations de menu ................................................Fr-11

Arborescence de menus ...........................................Fr-12

Dépannage................................................. Fr-14

Caractéristiques ......................................... Fr-15

Garantie limitée

Moniteurs Plasma....................... Fr-16

Contenu du colis

䡺 Moniteur à plasma (⳯1)

䡺 Cordon d’alimentation (⳯1, 3 m/9,8 pieds)

䡺 Télécommande (⳯1)

䡺 Piles AAA (⳯2, Piles au manganèse pour la

télécommande)

䡺 Manuels (Guide rapide et CD-ROM)

䡺 Âmes en ferrite pour cordon d’alimentation (⳯2),

bandes pour cordon d’alimentation (⳯2)

䡺 Âme en ferrite pour câble télécommande (⳯2)

䡺 Serre-câbles (⳯3), Colliers à perles (⳯3)

Options

• Unité de montage mural

• Unité de montage au plafond

• Unité de montage incliné

• Support sur table

• Haut-parleurs amovibles

Fr-2

Précaution

Veuillez lire avec attention ce manuel avant d’utiliser le moniteur à plasma

et le conserver accessible pour s’y référer ultérieurement.

ATTENTION..

RISQUE D’ELECTROCUTION

NE PAS OUVRIR

ATTENTION:

POUR EVITER TOUT RISQUE D’ELECTROCUTION,

NE PAS OUVRIR LE BOITIER. A L’INTERIEUR,

AUCUNE PIECE NE NECESSITE L’INTER-VENTION

DE L’UTILISATEUR. EN CAS DE PROBLEME,

S’ADRESSER A UN REPARATEUR SPECIALISTE.

Ce symbole est une mise en garde contre les risques

d’électrocution que présentent certaines parties

dépourvues d’isolation à l’intérieur de l’appareil. Il est

donc dangereux d’établir le moindre contact avec ces

parties.

Ce symbole avertit l’utilisateur que d’importantes

informations sont fournies sur le fonctionnement ou

l’entretien de cet appareil. De ce fait, il faut lire

attentivement ces instruc-tions pour éviter tout problèm.

AVERTISSEMENT

AFIN D’EVITER TOUT RISQUE D’INCENDIE OU

D’ELECTROCUTION, NE PAS EXPOSER CET APPAREIL A LA

PLUIE OU A L’HUMIDITE. NE PAS BRANCHER LA PRISE

D’ALIMENTATION POLARISEE DANS UNE PRISE MURALE

AVEC UNE RALLONGE OU UN ADAPTATEUR MULTIPRISE

SI LES FICHES NE PEUVENT ETRE INSEREES

COMPLETEMENT. EVITER D’OUVRIR LE BOITIER CAR

CELUI-CI PROTEGE DES COMPOSANTS FONCTIONNANT

A HAUTE TENSION. EN CAS DE PROBLEME, S’ADRESSER

A UN REPARATEUR SPECIALISTE.

Avertissements et précautions de

sécurité

Ce moniteur à plasma a été conçu et fabriqu pour une utilisation

fiable et durable. Il ne nécessite aucun entretien en dehors du

nettoyage. Voir la section “Méthode de nettoyage du moniteur à

plasma” plus loin.

Le panneau à affichage plasma est constitué de fines particules

d’images (cellules) dont plus de 99,99 % sont actives. Certaines

d’entre elles ne produisent pas de lumière ou restent allumées.

Pour des raisons de sécurité et pour éviter d’endommager l’appareil,

lire attentivement les instructions suivantes.

Pour éviter les risques d’éléctrocution et d’incendie:

Laisser suffisamment d’espace autour de l’appareil pour la ventilation et

éviter toute augmentation excessive de la température interne. Ne pas couvrir

les fentes d’aération ou installer l’appareil dans un endroit trop exigu.

Si vous installez l’appareil dans un espace clos, assurezvous qu’il y ait

suffisamment d’espace au dessus pour permettre l’air chaud de s’élever

et de s’évacuer.

Si la température du moniteur devient excessive, la protection contre

les surchauffes entrera en action et coupera l’alimentation. Dans ce cas,

éteindre l’appareil et débrancher le câble d’alimentation. Si la

température de la pièce dans laquelle se trouve le moniteur est

particulièrement élevée, déplacer celui-ci dans un endroit plus frais et

attendre environ 60 minutes qu’il refroidisse. Si le problème persiste,

prendre contact avec votre revendeur.

2. Ne pas raccorder la prise d’alimentation polarisée de ce périphérique à

une rallonge ou une prise murale si les fiches ne peuvent pas être

complètement insérées.

3. Ne pas exposer cet appareil à la pluie ou à l’humidité.

4. Eviter d’endommager le câble d’alimentation et ne pas le modifier.

5. Débrancher le câble d’alimentation électrique pendant les orages ou les

longues périodes d’inactivité.

6. Ne pas ouvrir le boîtier protégeant les parties dangereuses fonctionnant

hauts voltages. Si l’appareil est endommagé de cette manière, la garantie

sera annulée. De plus, les risques d’électrocution grave sont grands.

7. Ne pas essayer d’intervenir ou de réparer l’appareil. Le fabricant décline

toute responsabilité en cas de blessure corporelle ou de dégâts matériels

résultant d’une opération d’entretien quelconque effectuée par des

personnes non qualifiées ou résultant de l’ouverture du couvercle arrière.

S’adresser au service après-vente autorisé.

8. Cet équipement doit être connecté à une prise secteur (MAIN) équipée

d’une mise à la terre.

9. La prise secteur doit se trouver près de l’équipement et doit être facile

d’accès.

Pour éviter tout dommage et assurer une utilisation durable:

Utiliser seulement une alimentation en courant de 100 V à 240 V 50 Hz/60 Hz.

Toute utilisation prolongée avec un courant supérieur à 100 V à 240 V risque

de diminuer la durée de vie de l’appareil et même de provoquer un incendie.

2. Manipuler l’appareil avec précautions lors de son installation, ne pas le

laisser tomber.

3. L’installer loin de toute source de chaleur ou de poussière. Ne pas

l’exposer au soleil.

Eviter la pénétration de liquides ou petits objets métalliques l’intérieur de

l’appareil. En cas d’incident de ce genre, débrancher le câble d’alimentation

électrique et confier le moniteur à un service après-vente agréé.

5. Ne pas cogner ou rayer la surface de l’écran, des déformations de l’image

en résulteraient.

6. Pour un montage et une installation correcte, il est fortement

recommandé de faire appel à un revendeur agréé et qualifié.

7. Comme c’est le cas pour tout affichage à base de phosphore (comme

un moniteur CRT, par exemple), la puissance de lumière baisse

graduellement au cours de la vie du panneau d’affichage à plasma.

8. Pour éviter tout risque de sulfuration, il est fortement conseillé de ne

pas installer l’appareil dans un vestiaire, un bain public ou un bain de

source thermale.

9. Ne pas utiliser dans un véhicule en marche car l’unité pourrait tomber

ou glisser et provoquer des blessures.

10. Pour éviter l ‘inflammation ou les chocs électriques, ne pas placer l’unité

sur la tranche, à l’envers ou avec l’écran vers le bas ou vers le haut.

11. Pour éviter les risques d’incendie, ne placez aucune flamme nue (telle

qu’une bougie allumée) sur l’appareil.

Méthode de nettoyage du moniteur à plasma:

1. Nettoyer le panneau avant et le cadre en procédant à l’aide d’un chiffon

doux et sec. Ne jamais utiliser de solvents du type alcool ou diluant

pour le nettoyage de ces surfaces.

2. Nettoyer les prises d’aération du plasma en procédant à l’aide d’une

brosse à poils doux fixée à un aspirateur.

Pour garantir la bonne ventilation du moniteur, nettoyer les prises d’air

tous les mois. Un nettoyage plus fréquent peut s’avérer nécessaire selon

les conditions environnantes dans lesquelles le moniteur à plasma est utilisé.

Pour éviter les risques de brûlage du luminophore, les mesures

suivantes sont recommandées:

Comme tous les périphériques d’affichage à base luminophore et tous les

autres affichages gaz plasma, les moniteurs plasma peuvent être sujets au

brûlage du luminophore dans certaines circonstances. Certaines conditions

d’utilisation, telles que l’affichage continu d’une image statique pour une

durée prolongée, peuvent causer le brûlage du luminophore si aucune

précaution n’est prise. Pour protéger votre investissement dans ce moniteur

à plasma, veuillez suivre les directives et les conseils suivantes pour

minimiser l’occurence le marquage de l’écran:

* S’assurer de mettre en marche et d’utiliser l’économiseur d’écran chaque

fois que c’est possible, pendant l’utilisation avec une source d’entrée

venant d’ un ordinateur.

* Afficher une image en mouvement aussi souvent que possible.

* Changer la position de l’affichage de menu de temps à autre.

* Toujours couper l’alimentation après la fin de l’utilisation du moniteur.

Si le moniteur à plasma est en usage continu ou de longue durée, prendre

les mesures suivantes afin d’éviter l’occurence le brûlage du luminophore:

* Abaisser le niveau de l’image (contraste, luminance) autant que possible,

sans faire perdre la lisibilit de l’image.

* Afficher une image avec de nombreuses couleurs et graduations de

couleur (par ex. des images photo-graphiques ou photo-réalistes).

Créer un contenu d’image avec un contraste minimal entre les zones sombres

et les zones claires, par exemple des caractères blancs sur un fond noir.

Utiliser des couleurs complémentaires ou pastels le plus souvent possible.

* Eviter d’afficher des images avec peu de couleurs et des limites nettes et

clairement définies entre les couleurs.

Son de fonctionnement du moniteur plasma

Le panneau du moniteur plasma est composé de pixels extrêmement fins et

ces pixels émettent de la lumière en fonction des signaux vidéo reçus. Ce

principe peut créer un bourdonnement ou un ronflement électrique venant

du moniteur plasma. Veuillez également noter que la vitesse de rotation du

ventilateur de refroidissement peut augmenter lorsque la température

ambiante du moniteur plasma augmente. Lorsque cela se produit, il est

possible que vous entendiez le moteur du ventilateur.

Remarque:

Les éléments suivants ne sont pas couverts par la garantie.

• Rémanence

• Sons générés par le panneau, par exemple : Bruit du moteur de

ventilateur, ronflement du circuit électrique / bourdonnement du

panneau de verre.

Contactez un revendeur agréé ou un revendeur de marque pour d'autres

procédures qui conviendront le mieux à vos besoins particuliers.

Recommandations importantes

La page charge ...

NEC 60XM5, PX-60XM5A Manuel utilisateur

Marque: NEC

Modèle: 60XM5, PX-60XM5A

Catégorie: Téléviseurs à écran plasma

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: NEC 60XM5, PX-60XM5A User manual
español: NEC 60XM5, PX-60XM5A Manual de usuario
português: NEC 60XM5, PX-60XM5A Manual do usuário

NEC 60XM5, PX-60XM5A Manuel utilisateur

Ce manuel convient également à

NEC 60XM5, PX-60XM5A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents