Allen-Bradley FLEX I/O 1794-IR8 Installation Instructions Manual

Marque
Allen-Bradley
Modèle
FLEX I/O 1794-IR8
Taper
Installation Instructions Manual

  " #!!  % $# # 
$#  ' & 
   

(Cat. No. 1794-IR8)
 
This module mounts on a 1794 terminal base unit.
1. Rotate keyswitch (1) on terminal base unit (2) clockwise to position
3
as required for this type of module.
2. Make certain the flexbus connector (3) is pushed all the way to the left
to connect with the neighboring terminal base/adapter. You cannot
install the module unless the connector is fully extended.
3. Make sure that the pins on the bottom of the module are straight so
they will align properly with the connector in the terminal base unit.
4. Position the module (4) with its alignment bar (5) aligned with the
groove (6) on the terminal base.
5. Press firmly and evenly to seat the module in the terminal base unit.
The module is seated when the latching mechanism (7) is locked into
the module.
Installation Instructions
Allen-Bradley
24V dc FLEX I/O RTD Input Module2
   
!
ATTENTION: Remove field-side power before
removing or inserting this module. This module is
designed so you can remove and insert it under
backplane power. When you remove or insert a module
with field-side power applied, an electrical arc may
occur. An electrical arc can cause personal injury or
property damage by:
• sending an erroneous signal to your system’s field
devices causing unintended machine motion
• causing an explosion in a hazardous environment
Repeated electrical arcing causes excessive wear to
contacts on both the module and its mating connector.
Worn contacts may create electrical resistance.
   
If this product has the CE mark it is approved for installation within the
European Union and EEA regions. It has been designed and tested to meet
the following directives.
EMC Directive
This product is tested to meet Council Directive 89/336/EEC
Electromagnetic Compatibility (EMC) and the following standards, in
whole or in part, documented in a technical construction file:
• EN 50081-2 EMC – Generic Emission Standard, Part 2 – Industrial
Environment
• EN 50082-2 EMC – Generic Immunity Standard, Part 2 – Industrial
Environment
This product is intended for use in an industrial environment.
Low Voltage Directive
This product is tested to meet Council Directive 73/23/EEC Low Voltage,
by applying the safety requirements of EN 61131–2 Programmable
Controllers, Part 2 – Equipment Requirements and Tests.
For specific information required by EN 61131-2, see the appropriate
sections in this publication, as well as the following Allen-Bradley
publications:
• Industrial Automation Wiring and Grounding Guidelines For Noise
Immunity, publication 1770-4.1
• Automation Systems Catalog, publication B111
This equipment is classified as open equipment and must be mounted in
an enclosure during operation to provide safety protection.
24V dc FLEX I/O RTD Input Module 3
Publication 1794Ć5.22 - May 1999

1. Connect the individual high and low signal wiring to numbered
terminals on the 0–15 row (A) on the terminal base unit as indicated
in the wiring table.
2. Connect 24V dc common to terminal 16 on row (B).
!
ATTENTION: You must power this module from the same
power supply that supplies the adapter module so they both
power up or down together. You must cycle power for the
adapter to recognize this module.
3. Connect individual channel signal returns to the associated terminal
on row (B) as shown in the wiring table.
Important: Use the following Belden cables for connecting the RTD to
the terminal base unit:
        
2Ćwire Not applicable 9501
3Ćwire Less than 100ft (30.5m) with normal humidity 9533
Over 100ft (30.5m)  high humidity
1
83503
1
Greater than 55% for more than 8 hours
4. Connect individual channel shield returns to the associated terminal
on row (B) for 1794-TB3 and -TB3S or row (C) for the 1794-TB3T or
-TB3TS as shown in the wiring table.
5. Connect +24V dc to terminal 34 on the 34-51 row (C).
ATTENTION: To reduce susceptibility to noise, power
analog modules and digital modules from separate power
supplies. Do not exceed a length of 33 ft (10m) for dc
power cabling.
ATTENTION: Do not daisy chain power or ground from
this terminal base unit to any ac or dc digital module
terminal base units.
6. If daisy-chaining 24V dc common, connect jumper from terminal 33
to terminal 16 on the next terminal base unit.
7. If daisy-chaining +24V dc, connect jumper from terminal 51 to
terminal 34 on the next terminal base unit.
Allen-Bradley
24V dc FLEX I/O RTD Input Module4
Publication 1794Ć5.22 - May 1999
8. Connect the shield to functional earth ground as near as possible to
the module.
ATTENTION: Total current draw through the terminal
base unit is limited to 10A. Separate power connections to
the terminal base unit may be necessary.
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16
12 34567891011121314150
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
34
1794ĆTB3, ĆTB3S, ĆTB3T
0 -15
34-51
16-33
A
B
C
RTD
1794ĆTB3 and ĆTB3S Terminal Base Units
RTD
Channel
High Signal
Terminal
Low Signal
Terminal
Signal
Return
1
Shield
Return
0 0 1 17 18
1 2 3 19 20
2 4 5 21 22
3 6 7 23 24
4 8 9 25 26
5 10 11 27 28
6 12 13 29 30
7 14 15 31 32
24V dc Common 16 thru 33
+24V dc power 34 thru 51
1
When using a 2Ćwire RTD, jumper the signal return to the low signal terminal.
24V dc FLEX I/O RTD Input Module 5
Publication 1794Ć5.22 - May 1999
RTD
1794ĆTB3T and ĆTB3TS Terminal Base Units
RTD
Channel
High Signal
Terminal
Low Signal
Terminal
Signal
Return
Shield
Return
1
0 0 1 17 39
1 2 3 19 40
2 4 5 21 41
3 6 7 23 42
4 8 9 25 43
5 10 11 27 44
6 12 13 29 45
7 14 15 31 46
24V dc Common 16, 17, 19, 21, 23, 25, 27, 29, 31 and 33
+24V dc power 34 and 51
1
Terminals 39 to 46 are chassis ground.
Example of 2Ć, 3Ć and 4Ćwire RTD Wiring to a 1794ĆTB3 Base Unit
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16
12 34567891011121314150
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
34
1794ĆTB3
0 -15
34-51
16-33
A
B
C
4ĆWire RTD 2ĆWire RTD3ĆWire RTD
Clip or tieback
4th lead.
Attention: Keep exposed area of inner conductor as short as possible.
Allen-Bradley
24V dc FLEX I/O RTD Input Module6
.'% -%)( 1 0 
Example of 2Ć, 3Ć and 4Ćwire RTD Wiring to a 1794ĆTB3T Base Unit
                
    

 
                

1794ĆTB3T
0 -15
34-51
16-33
A
B
C
3ĆWire RTD 2ĆWire RTD
4ĆWire RTD
'%* )+ -%" &
-$ '"!
Attention: ""* "/*),"! +" )# %(("+ )(!. -)+ , ,$)+- , *),,%'"
Indicators
       
   
3


AB
+
_
+
_
+
_
+
_
+
_
+
_
+
_
+
_

A = Status Indicator – indicates diagnostics results and
configuration status.
B = Insertable label for writing individual input designations.
24V dc FLEX I/O RTD Input Module 7
Publication 1794Ć5.22 - May 1999
Block Transfer Read and Write
The following block transfer read and write word bit information is
presented for experienced users only. Refer to the user manual
(publication 1794-6.5.4) for this product for complete information on
programming and configuring your module.
Read Words
Dec. Bit
Word
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
0 Reserved
1 Channel 0 Input Data
2 Channel 1 Input Data
3 Channel 2 Input Data
4 Channel 3 Input Data
5 Channel 4 Input Data
6 Channel 5 Input Data
7 Channel 6 Input Data
8 Channel 7 Input Data
9 Overrange Bits Underrange Bits
10 0 0 0 0 0
Bad
Cal
Cal
Dne
Cal
Rng
RIUP
Critical Error
Bits
Pwr
Up
Res. 0 0
Write Words
Dec. Bit
Word
15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
0 8Ćbit Calibration Mask
Cal
Clk
Cal
Hi
Cal
Lo
Filter Cutoff Enh MDT
1 RTD3Type RTD2Type RTD1Type RTD0Type
2 RTD7Type RTD6Type RTD5Type RTD4Type
Where: Enh = Enhanced mode
MDT = Module data type
Allen-Bradley
24V dc FLEX I/O RTD Input Module8
Publication 1794Ć5.22 - May 1999
Data Type
Word Description
Write word
0
Module Data Type
0
01 00 Bits
0 0
o
C (default)
0 1
o
F
1 0 Bipolar counts scaled between -32768 and +32767
1 1 Unipolar counts scaled between 0 and 65535
RTD Type
Word Description
RTD Type - Range
Write Word 1
Bit 03 02 01 00 Channel 0
0 0 0 0 Resistance (default)
0 0 0 1 No sensor connected - do not scan
0 0 1 0 100 ohm Pt α = 0.00385 Euro (-200 to +870
o
C)
0 0 1 1 100 ohm Pt α = 0.003916 U.S. (-200 to +630
o
C)
0 1 0 0 200 ohm Pt α = 0.00385 Euro (-200 to +630
o
C)
0 1 0 1 500 ohm Pt α = 0.00385 Euro (-200 to +630
o
C)
0 1 1 0 Reserved
0 1 1 1 10 ohm Copper (-200 to +260
o
C)
1 0 0 0 120 ohm Nickel (-60 to +250
o
C)
1 0 0 1 100 ohm Nickel (-60 to +250
o
C)
1 0 1 0 200 ohm Nickel (-60 to +250
o
C)
1 0 1 1 500 ohm Nickel (-60 to +250
o
C)
1 1 0 0 Reserved
24V dc FLEX I/O RTD Input Module 9
#" &  % 
  
 "  
"#
"
     ! "!  $ 
"#
     ! "!  $ 
     ! "!  $ 
 "   "
     ! "!  $ 
     ! "!  $ 
     ! "!  $ 
     ! "!  $ 
Allen-Bradley
24V dc FLEX I/O RTD Input Module10
Publication 1794Ć5.22 - May 1999
   
CSA
certifies products for general use as well as for use in hazardous locations. 
        as shown below, and not by
statements in any user documentation.
Example of the CSA certification product label
To comply with CSA certification for use in hazardous locations, the following information
becomes a part of the product literature for CSAĆcertified AllenĆBradley industrial control
products.
• This equipment is suitable for use in Class I, Division 2,
Groups A, B, C, D, or nonĆhazardous locations only.
• The products having the appropriate CSA markings (that is, Class I Division 2, Groups
A, B, C, D), are certified for use in other equipment where the suitability of combination
(that is, application or use) is determined by the CSA or the local inspection office
having jurisdiction.
 Due to the modular nature of a PLC
control system, the product with the
highest temperature rating determines the overall temperature code rating of a PLC
control system in a Class I, Division 2 location. The temperature code rating is marked on
the product label as shown.
Temperature code rating
Look for temperature code
rating here
The following warnings apply to products having CSA certification for use in hazardous
locations.
24V dc FLEX I/O RTD Input Module 11
Publication 1794Ć5.22 - May 1999
CSA Hazardous Location Approval
!
ATTENTION: Explosion hazard Ċ
• Substitution of components may impair suitability for Class I,
Division 2.
• Do not replace components unless power has been switched off or
the area is known to be nonĆhazardous.
• Do not disconnect equipment unless power has been switched off or
the area is known to be nonĆhazardous.
• Do not disconnect connectors unless power has been switched off or
the area is known to be nonĆhazardous. Secure any userĆsupplied
connectors that mate to external circuits on an AllenĆBradley product
using screws, sliding latches, threaded connectors, or other means
such that any connection can withstand a 15 Newton (3.4 lb.)
separating force applied for a minimum of one minute.
Approbation d'utilisation dans des emplacements dangereux par la CSA
La CSA
certifie les produits d'utilisation générale aussi bien que ceux qui s'utilisent dans
des emplacements dangereux. La certification CSA en vigueur est indiquée par
l'étiquette du produit et non par des affirmations dans la documentation à l'usage des
utilisateurs.
Exemple d'étiquette de certification d'un produit par la CSA
I
Pour satisfaire à la certification de la CSA dans des endroits dangereux, les informations
suivantes font partie intégrante de la documentation des produits industriels de contrôle
AllenĆBradley certifiés par la CSA.
• Cet équipement convient à l'utilisation dans des emplacements de Classe I, Division 2,
Groupes A, B, C, D, ou ne convient qu'à l'utilisation dans des endroits non dangereux.
• Les produits portant le marquage approprié de la CSA (c'est à dire, Classe I, Division
2, Groupes A, B, C, D) sont certifiés à l'utilisation pour d'autres équipements où la
convenance de combinaison (application ou utilisation) est déterminée par la CSA ou
le bureau local d'inspection qualifié.
Important: Par suite de la nature modulaire du système de contrôle PLC
, le produit
ayant le taux le plus élevé de température détermine le taux d'ensemble du code de
température du système de contrôle d'un PLC dans un emplacement de Classe I, Division
2. Le taux du code de température est indiqué sur l'étiquette du produit.
Allen-Bradley
24V dc FLEX I/O RTD Input Module12
Publication 1794Ć5.22 - May 1999
CSA Hazardous Location Approval
Approbation d'utilisation dans des emplacements dangereux par la CSA
Le taux du code de
température est indiqué ici
Taux du code de température
I
Les avertissements suivants s'appliquent aux produits ayant la certification CSA pour leur
utilisation dans des emplacements dangereux.
!
AVERTISSEMENT: Risque d'explosion Ċ
• La substitution de composants peut rendre ce matériel inacceptable
pour lesemplacements de Classe I, Division 2.
• Couper le courant ou s'assurer quel'emplacement est désigné non
dangereux avant de remplacer lescomposants.
• Avant de débrancher l'équipement, couper le courant ou s'assurer
que l'emplacement est désigné non dangereux.
• Avant de débrancher les connecteurs, couper le courant ou
s'assurer que l'emplacement est reconnu non dangereux. Attacher
tous connecteurs fournis par l'utilisateur et reliés aux circuits
externes d'un appareil AllenĆBradley à l 'aide de vis, loquets
coulissants, connecteurs filetés ou autres moyens permettant aux
connexions de résister à une force de séparation de 15 newtons (3,4
lb. Ć 1,5 kg) appliquée pendant au moins une minute.
Le sigle CSA est la marque déposée de l'Association des Standards pour le Canada.
PLC est une marque déposée de AllenĆBradley Company, Inc.
CSA logo is a registered trademark of the Canadian Standards Association
PLC is a registered trademark of AllenĆBradley Company, Inc.
24V dc FLEX I/O RTD Input Module 13
Publication 1794Ć5.22 - May 1999
Specifications - 1794ĆIR8 RTD Input Module
Number of Inputs 8 Channels
Module Location Cat. No. 1794ĆTB3, ĆTB3S, ĆTB3T, and ĆTB3TS
Terminal Base Units
Signal Input Range 1 to 433 ohms
Sensors Supported Resistance:
100 ohm Pt α = 0.00385 Euro (-200 to +870
o
C)
100 ohm Pt α = 0.003916 U.S. (-200 to +630
o
C)
200 ohm Pt α = 0.00385 Euro (-200 to +630
o
C)
500 ohm Pt α = 0.00385 Euro (-200 to +630
o
C)
100 ohm Nickel α = 0.00618 (-60 to +250
o
C)
120 ohm Nickel α = 0.00672 (-60 to +250
o
C)
200 ohm Nickel α = 0.00618 (-60 to +250
o
C)
500 ohm Nickel α = 0.00618 (-60 to +250
o
C)
10 ohm Copper α = 0.00427 (-200 to +260
o
C)
Resolution 16 bits across 435 ohms
Data Format 16Ćbit 2's complement or offset binary
Normal Mode Noise Rejection 60db @ 60Hz for A/D filter cutoff @ 10Hz
Accuracy without calibration (at low
humidity)
Normal mode: 0.05% Full Scale (maximum)
Enhanced mode: 0.01% Full Scale (typical)
Common Mode Rejection -120db @ 60Hz; -100db @ 50Hz with A/D filter
cutoff @ 10Hz
Common Mode Voltage 0V between channels (common return)
System Throughput
Normal mode:
Enhanced mode:
Programmable from 28ms/channel to
325ms/channel
325ms (1 channel scanned)
2.6s (8 channels scanned)
Programmable from 56ms/channel to
650ms/channel
650ms (1 channel scanned)
2.925s (8 channels scanned)
Settling Time to 100% of final value Available at system throughput rate
Open RTD Detection Out of range reading (upscale)
Open Wire Detection Time Available at system throughput rate
Overvoltage Capability 35V dc, 25V ac continuous @ 25
o
C
250V peak transient
Channel Bandwidth dc to 2.62Hz (-3db)
Specifications continued on next page.
Allen-Bradley
24V dc FLEX I/O RTD Input Module14
Publication 1794Ć5.22 - May 1999
    
RFI Immunity Error of less than 1% of range at 10V/M
27 to 1000MHz
Input Offset Drift with Temperature 1.5 milliohm/
o
C maximum
Gain Drift with Temperature Normal mode: 20 ppm/
o
C maximum
Enhanced mode: 10 ppm/
o
C maximum
RTD Excitation Current 718.39µA
Indicators 1 red/green status indicator
Flexbus Current 20mA
Power Dissipation 3W maximum @ 31.2V dc
Thermal Dissipation Maximum 10.2 BTU/hr @ 31.2V dc
Keyswitch Position 3
Cable Requirements 2Ćwire, Belden 9501
3 Ćwire, less than 100ft (30.5m) with normal
humidity- Belden 9533
3 Ćwire, greater than 100ft (30.5m)  high
humidity (>55% for >8 hrs)- Belden 83503
 
External dc Power
Supply Voltage
Voltage Range
Supply Current
24V dc nominal
19.2 to 31.2V dc (includes 5% ac ripple)
19.2V dc for ambient temperatures < 55
o
C
24V dc for ambient temperatures < 55
o
C
31.2V dc for ambient temperatures < 40
o
C
See derating curve.
140mA @ 24V dc
Dimensions Inches
(Millimeters)
1.8H x 3.7W x 2.1D
(45.7 x 94.0 x 53.3)
Environmental Conditions
Operational Temperature
Storage Temperature
Relative Humidity
Shock Operating
Nonoperating
Vibration
0to55
o
C (32 to 131
o
F)
-40 to 85
o
C (-40 to 185
o
F)
5 to 95% noncondensing (operating)
5 to 80% noncondensing (nonoperating)
30 g peak acceleration, 11(+
1)ms pulse width
50 g peak acceleration, 11(+1)ms pulse width
Tested5g@10-500Hz per IEC 68Ć2Ć6
Specifications continued on next page.
24V dc FLEX I/O RTD Input Module 15
Publication 1794Ć5.22 - May 1999
"! &  #" #
Agency Certification
(when product is marked)
• CSA certified
• CSA Class I, Division 2
Groups A, B, C, D certified
• UL listed
• CE marked for all applicable directives
User Manual Publication 1794Ć6.5.4
19.2
24.0
31.2
25
o
C40
o
C50
o
C55
o
C
! #%
" "# 
 " # $
0
o
C
Safe operating area
The area within the curve represents the safe operating range for the module under
various conditions of user supplied 24V dc supply voltages and ambient temperatures.
Allen-Bradley
24V dc FLEX I/O RTD Input Module16
Publication 1794Ć5.22 - May 1999
Thank you for purchasing this product. This product has a user manual
associated with it. If you would like a manual, you can:
download a free electronic version from the internet::
www.ab.com/manuals or
www.theautomationbookstore.com
purchase a printed manual by:
– contacting your local distributor or Rockwell
Automation representative,
– visiting www.theautomationbookstore.com and placing
your order
– calling 1.800.963.9548 (USA/Canada) or 001.330.725.1574
(Outside USA/Canada)
The publication number of the user manual for your product is listed under
Specifications" in this installation instruction.
 
Publication 1794Ć5.22 - May 1999
Supersedes publication 1794Ć5.22 - September 1996
PN955126-12B
Copyright 1999 AllenĆBradley Company, Inc. Printed in USA
With major offices worldwide.
World Headquarters,
AllenĆBradley,
1201 South Second Street,
Milwaukee, WI 53204 USA,
Tel: (1) 414 382Ć2000 Fax: (1) 414 382Ć4444
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Allen-Bradley FLEX I/O 1794-IR8 Installation Instructions Manual

Marque
Allen-Bradley
Modèle
FLEX I/O 1794-IR8
Taper
Installation Instructions Manual
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents