Aiwa AV-DV70 Operating Instructions Manual

Marque: Aiwa

Modèle: AV-DV70

Catégorie: Récepteurs AV

Taper: Operating Instructions Manual

\8-ARl-903-01

180401 CCK-Y-9

For assistance and information

call toll free I-800-BUY4WA

(United States and Puerto Rico)

“CAUTION:TO REDUCE THE RISK OF

ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.”

Owner’s record

For your convenience, record the model number and serial

number (you will find them on the rear of your unit) in the space

provided below. Please refer to them when you contact your

Aiwa dealer in case of difficulty.

Model No. Serial No. (Lot No.)

AV-DV70

PRECAUTIONS

Read the Operating Instructions carefully and completely before

operating the unit. Be sure to keep the Operating Instructions

for future reference. All warnings and cautions in the Operating

Instructions and on the unit should be strictly followed, as well

as the safety suggestions below.

Installation

Water and moisture — Do not use this unit near water, such

as near a bathtub, washbowl, swimming pool, or the like.

Heat — Do not use this unit near heat sources, including

heating vents, stoves, or other appliances that generate heat.

It also should not be placed in temperatures less than 5°C

(41”F) or higher than 35°C (95”F).

Mounting surface — Place the unit on a flat, even surface.

Ventilation — The unit should be situated with adequate

space around it so that proper heat ventilation is assured.

Allow 10 cm (4 in.) clearance from the rear and the top of the

unit, and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface that

may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or airtight

rack where ventilation may be impeded.

Objects and liquid entry — Take care that objects or liquids

do not get inside the unit through the ventilation openings.

Carts and stands — When placed or

mounted on a stand or cart, the unit

should be moved with care.

Quick stops, excessive force, and

uneven surfaces may cause the unit or

●3

AA*

cart to overturn or fall.

Wall or ceiling mounting —The unit should not be mounted

on a wall or-ceiling, u;less specified in the Operating

Instructions.

Power sources — Connect this unit only to power sources

specified in the Operating Instructions, and as marked on

the unit.

Polarization — As a safety feature, some units are equipped

with polarized AC power plugs which can only be inserted

one way into a power outlet. If it is difficult or impossible to

insert the AC power plug into an outlet, turn the plug over

and try again. If it is not still inserted easily into the outlet,

pIease call a qualified service technician to service or replace

the outlet. To avoid defeating the safety feature of the

polarized plug, do not force it into a power outlet.

AC power cord

- When disconnecting the AC power cord, pull it out by the

AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands, as this

could result in fire or shock.

- Power cords should be firmly secured to avoid being

severely bent, pinched, or walked upon. Pay particular

attention to the cord from the unit to the power socket.

- Avoid overloading AC power plugs and extension cords

beyond their capacity, as this could result in fire or shock.

Extension cord — To help prevent electric shock, do not

use a polarized AC power plug with an extension cord,

receptacle, or other outlet unless the polarized plug can be

completely inserted to prevent exposure of the blades of the

plug.

When

not in use— Unplug the AC power cord from the AC

power outlet if the unit will not be used for several months or

more. When the cord is plugged in, a small amount of current

continues to flow to the unit, even when the power is turned

off.

1 ENGLISH

Outdoor Antenna

1 Power lines — When connecting an outdoor antenna, make

sure it is located away from power lines,

2 Outdoor antenna grounding — Be sure the antenna system

is properly grounded to provide protection against unexpected

voltage surges or static electricity build-up. Article 810 of the

National Electrical Code, ANS1/NFPA70, provides information

on proper grounding of the mast, supporting structure, and

the lead-in wire to the antenna discharge unit, as well as the

size of the grounding unit, connection to grounding terminals,

and requirements for grounding terminals themselves,

Antenna Grounding According to the National Electrical Code

)

(NECART250PARTH)

NEC-NATIONAL ELECTRICAL CODE

Maintenance

Clean the unit only as recommended in the Operating

Instructions.

Damaae Reauirina Service

Have the unit serviced by a qualified service technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have gotten inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been damaged

DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF.

Check

your unit and accessories

AV-DV70 Stereo receiver Remote control

FM antenna

AM antenna

Operating Instructions, etc.

TABLE (IF CONTENTS

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I

PREPARATIONS

CONNECTIONS ..................................................................3

BEFORE OPERATION ........................................................ 7

SETTING THE CL[3CK .........................................................7

SOUND

CUSTOM AUDIO ADJUSTMENT ..................................... . 8

ELECTRONIC GRAPHIC EQUALIZER ............................ . 9

DsPsuRRouND .............................................................m....9

BASIC OPERATICINS

SELECTION OF AUDIO/VIDEO SOURCE ....................... 10

RECORDING AN AUDIO SOURCE ................................. 11

RADIO RECEPTIC)N

MANUAL TUNING .............. .............................................. 12

DIRECT TUNING ............................................................... 12

PRESETTING STATIONS ................................................. 13

DOLBY SURROUND

SELECTING DOLE3Y SURROUND ................................... 14

ADJUSTING SPEAKER LEVEL BALANCE .................... 15

ADJUSTING DOL13Y DIGITAL SURROUND SOUND .....17

REMOTE CONTROL

OPERATING TV, CABLE TV, VCR AND CD PLAYER ......18

ON SCREEN DISPLAY ..................................................... 19

TIMER

SETTING THE SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

GENERAL

CARE AND MAINTENANCE ............................................ 20

SPECIFICATIONS ............................................................. 20

TROUBLESHOOTIING GUIDE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

PARTS INDEX ...............m..................................................m22

APPENDIX

ID CODES FOR Tir .......................................................... A-1

ID CODES FOR CABLE TV ............................................ A-2

ID CODES FOR VCR ...................................................... A-3

ID CODES FOR CD PLAYER ......................................... A,-4

EMGLBH

CONNECTIONS

CONNECTING EQUIPMENT

Jacks and plugs of the connecting cord are color-coded as

follows:

Before connecting the AC cord

Red jacks and plugs : For the right channel of audio signals

The rated voltage of your unit shown on the rear panel is 120 V

White jacks and plugs: For the left channel of audio signals

AC. Check that the rated voltage matches your local voltage.

Yellow jacks and plugs: For video signals

IMPORTANT

Connect the speakers, antennas, and all other external

Insert the plugs fully into the jacks. Loose connections may

equipment first. Then connect the AC cord at the end.

produce a humming sound or other noise interference.

*’ Be sure to connect the VIDEO OUT terminal of a DVD player

directly to aTV set, not through this unit. Otherwise, the picture

noise may appear when playing copy protected DVDS.

= ~~

‘2 Input sound through the DIGITAL IN terminals cannot be

mm ~Rmuu .—=... o

recorded, When recording the sound from the DVD or LD

Q“” C@l===

player, connect the analog AUDIO OUT terminals of the player

to the corresponding AUDIO IN terminals of the receiver.

‘3 When connecting a monaural video, use a stereo-mono

V;DZQ3

connecting cord (not supplied).

‘4 When connecting an LD player equipped with the AC-3 RF

OUT terminal, use an RF demodulator unit. Also connect the

analog AUDIO OUT terminals of the LD player to the receiver

to play all the sources. For further information, refer to the

instructions of the LD player.

DVD or Video 1*3IMD

player

1(—1 o . 1

to VIDEO IN

to AUDIOOUTPUT

Optical

connecting 1-

to VIDEOOUT(Video

1111

1)“

cord “

I .- ..” )11

(

Ill

Coaxial---4

connecting

7 mF

to COAXIAL

“G’TAL ‘UT +

RF demodulator*4

I Ill

Video 2*3or

LDWCable TV G=J

to AUDIOIN (Video2)

to VIDEO IN(Video2)

w I

CD player

Turntable

3 ENGLISH

CONNECTING SPEAKERS @

Speaker terminals

Connect front speakers (system A and/or B), a center speaker,

surround speakers and sub woofer to the corresponding speaker

terminals on the unit:

- the front speaker cords to the FRONT SPEAKERS terminals

- the center speaker cord to the CENTER SPEAKER terminals

- the surround speaker cords to the SURROUND SPEAKERS

terminals,

- for more powerful bass, the sub woofer (with a built-in amplifier)

cord to the SUPER WOOFER d jack

Speaker impedance

* Front and center speakers

Use the same impedance for both the front and center speakers.

The SPEAKER IMPEDANCE SELECTOR on the rear should be

set to the position that matches the impedance value of the front

and center speakers.

When using 4 ohm speakers, set the selector to IMP:4L2. When

using 8 ohm speakers, set the selector to IMP:8Q, Please unplug

the AC cord before setting the selector,

* Surround speakers and super woofer

The SPEAKER IMPEDANCE SELECTOR has no effect on the

SURROUND SPEAKERS terminals and the SUPER WOOFER

4 jack. For the surround speakers and sub woofer, use speakers

of 8 ohms or more.

Front sneakers

Lift up the terminal flap,

insert the speaker cord lead

into the terminal slot, then

close the flap. Check that the

cord is connected securely.

Surround speakers

“e

.—

—r——————

Connecting + to +, – to – terminals

To get the proper sound effect, the speaker terminals on the unit

SELECTOR

and the speaker should be connected with proper polarity; the +

terminal on the unit should be connected to the + terminal on

the speaker (and – to –).

* Be sure to connect the speaker cords correctly as shown in

the illustration on the right column. Improper connections can

cause short circuits in the SPEAKER(S) terminals.

● Do not leave objects generating magnetism near the speakers.

ENGLISH’4

POSITIONING THE SPEAKERS

Position the speakers to make the most of the Dolby Digital

Surround, Dolby Pro Logic or DSP effect.

@ Front speakers

@ Center speaker

Position in the center of the two front speakers. In addition,

position on or below the TV set, if connecting a TV set to the

unit.

@ Surround speakers

Place the surround speakers directly to the side of or slightly

behind the listening area. Align them horizontally, about 1

meter (3.2 feet) above ear height.

Sub woofer

Place the sub woofer in any place between the two front

speakers.

When not connecting the sub

woofer, be sure to select the

“SUBW OFF (sub woofer off) mode (see page 7).

Sound from the surround speakers or center speaker depends

on the setting of the DSP, Dolby Pro Logic and Dolby Digital

Surround,

@ @

69(9

CONNECTING THE SUPPLIED ANTENNAS @

Connect the FM antenna to the FM 75 Q terminals and the AM

antenna to the AM LOOP terminals.

FM antenna

)

(

To stand the AM loop antenna on a surface

Fix the claw to the slot as shown in the illustration.

To position the antennas

FM feeder antenna:

Extend this antenna horizontally in a T shape and fix its ends to

the wall.

AM loop antenna:

Position for the best reception.

● Do not bring the FM antenna near metal objects or curtain rails.

● Do not bring the AM antenna near other external equipment,

the unit itself, the AC power cord or speaker cords, as noise

will be picked up.

● Do not unwind the AM loop antenna wire.

CONNECTING AN OUTDOOR ANTENNA

For better FM reception, use of an outdoor antenna is

recommended. Connect the outdoor antenna to the FM 75 Q

terminals.

5 ENGLISH

USINGI WITH TV

When you operate the receiver, you can check the receiver

settings on the TV screen, if the connected TV is turned on (On

Screen Display function). The following screen shows the sound

effect settings of the Dolby Digital Surround.

For the further details, see “ON SCREEN DISPLAY” on page

DOLBY DGTL SU~N NORMAL

SUBW

L LVL MAX

CEN LVL

OdE

MAX

~R ~!k OdB

SL LVL OdB

CEN DELAY Orns

SUR DELAY 5ms

LFE LVL

OdB

MIDNIGHT STD

● The TV screen turns to blue if the TV signal or video signal

sent from the VCR/camcorder is weak or unlocked to the sync

signal. The screen restores the proper indication when the TV/

video signal turns to good condition.

● The video recording (connected to the VIDEO OUT jack of the

unit) is not affected by the screen indication, even if the screen

has changed to blue.

AB3UTTHE REMOTE CONTROL

Inserting batteries

Detach the battery cover on the rear of the remote control and

insert two R6 (size AA) batteries.

R6(AA)

When to replace the batteries

The maximum operational distance between the remote control

and the sensor on the unit should be approximately 5 meters

(16 feet). When this distance decreases, replace the batteries

with new ones.

Using the remote control

The instructions in this manual refer mainly to the buttons on the

main unit. Buttons on the remote control with the same names

as those on the main unit can be used as well.

c If the unit is not going to be used for an extended period of

time, remove the batteries to prevent possible electrolyte

leakage.

● The remote control may not operate correctly when:

- The line of sight between the remote control and the remote

sensor in the display window is exposed to intense light, such

as direct sunlight.

- Other remote controls are used nearby (those of a television,

etc.)

Remote control operation

This remote control system allows you to operate other external

equipment besides the AIWA receiver. For details of the rennote

control operation for other external equipment, see “REMOTE

CONTROL” on page 18.

The following is an explanation on how to operate the Aiwa

receiver.

C=l

RECEIVER/DIGIT

AIWA

RECEIVER —

SET UP

MUTE —

POWER —

TUNER PRESET/

SURROUND

‘uNcT’ON-evOLuM

Press the AIWA RECEIVER button ta set the

remote controll to the

Aiwa receiver mode.

Press one of the buttons indicated above.

FUNCTION button

Each time this button is pressed, the sound source changes

FM (or AM)’) +V3+V2+V1+CD+AUX+ PHOIVO

cyclically.

a): The band, which you have tuned to for the last time, cotmes on.

TUNER PRESET/S~JRROUND buttons

❑

Tune in the station which has been preset on the receiver.

To go to a higher preset number, press the UP~ button. To

go to a lower preset number, press the DOWN 1+1 button.

This button is also used when adjusting the speaker level

balance of the DSP, Dolby Pro Logic or Dolby Digital Surround

mode.

It is not necessary to press the AIWA RECEIVER button each

time you operate the Aiwa receiver unless another mode has

already been set. (See “REMOTE CONTROL” on page 18.)

If the receiver cannot be operated with the remote

control

Follow the steps below using the remote control.

Press the AIWA RECEIVER button.

Press and hold the SET UP button for -about 2.5

seconds.

The indicator on the top of the remote control blinks twice

while pressing this button.

Press the DIGIT buttons in the order of “4;’ “O”

and “6.”

ENGLISH 6

BEFORE OPERATION

SETTING THE CLOCK

DOLBY SURROUND

IER MANUAL SELECT

VOLUME

II Function indicators

PHONES

TAPE MONITOR

Function

buttons

FRONT SPEAKERS A, B

To turn the unit on

Press one of the function buttons (TUNER, PHONO,

AUX, CD, VIDEO I, VIDEO 2 or VIDEO 3) or the TAPE

MONITOR button.

When pressing the TUNER button, the previously tuned

station is received (Direct Play Function).

The POWER button is also available,

Operation is possible after four seconds, while the VOL

(volume) level or function name is displayed one after the

other and the selected function indicator flashes.

To select the front speaker system

To use speaker system A: Set the FRONT SPEAKERS A button

to -ON.

To use speaker system B: Set the FRONT SPEAKERS B button

to sON.

To use both speaker systems: Set both the buttons to ~ ON.

Set the button(s) to 10FF to turn off the speaker system(s).

As the front s~eaker svstems A and B are connected in series:

- The sound will dec;ease slightly when using both speaker

systems

- No sound can be heard if the FRONT SPEAKERS A and B

buttons are set to -ON when only one speaker system is

connected

When not connecting a sub woofer

Be sure to select the “SUBW OFF mode.

After pressing the DOLBY SURROUND button to turn on the

Dolby Pro Logic, press the MANUAL SELECT button once

so that “SUBW ON” appears on the display. Then press the

UPA button within four seconds to displav “SUBW OFF.”

Using the headphones

Connect headphones to the PHONES jack with a standard stereo

plug (06.3 mm, 1/4 inch). Be sure to set the FRONT SPEAKERS

A and B buttons to AOFF. Otherwise sound is output from the

speakers.

CLOCK

,y,5

2,4

When the AC cord is connected for the first time, the clock on

the display flashes.

Set the time as follows while the power is off.

Press the SET button.

The hour flashes.

Press the DOWNY or UPA button to designate

the hour.

Press the SET button to set the hour.

The hour stops flashing and the minute starts flashing,

Press the DOWNV or UPA button to designate

the minute.

5 Press the SET button to set the minute.

The minute stops flashing on the display and the clock starts

from 00 seconds.

To correct the current time

Press the POWER button to turn the unit off. Press the SET

button and carry out steps 1 to 5 above.

To display the current time

Press the CLOCK button on the remote control. The clock is

displayed for 4 seconds.

To switch to the 24-hour standard

Press the POWER button while pressing the UPA or DOWNY

button while the current time is displayed.

Repeat the same procedure to restore the 12-hour standard.

If the clock display flashes while the power is off

This is caused by a power interruption. The current time needs

to be reset.

If power is interrupted for more than approximately 24 hours, all

settings stored in memory after purchase need to be reset.

When the headphones are plugged in:

- The Dolby Pro Logic or DSP system is automatically canceled

- The “DOLBY DIGITAL SUR” or”3 STEREO” mode of the Dolby

Digital Surround is changed to the “2CH STEREO mode

To turn the unit off, press the POWER button.

7 ENGLISH

CUSTOM AUDIO ADJUSTMENT

SUPER T-BASS SYSTEM

BBE

MUTING BALANCE

VOLUME CONTROL

Turn the VOLUME control on the unit, or press the VOLUME

buttons on the remote control.

The volume level is shown on the display for four seconds. It

can be adjusted between O and MAX (31). It flashes when set

over the level of 21.

The volume level remains memorized even after the power is

turned off. However, if the power is turned off when the volume

is set to more than 17, it is automatically set to 16 the next time

the power is turned on.

To adjust the Ieft/right balance of the front speakers

Press the BALANCE button to display “L/R OdB. Then press

the DOWNV or UPA button repeatedly within four seconds.

Note that the front speaker balance for the Dolby Digital and

Dolby Pro Logic modes is also changed.

To mute the sound temporarily

Press the MUTING button (–20 dB).

“MUTE ON” appears on the display for four seconds. While

muting the sound, the selected function indicator flashes. Press

the MUTING button again to restore the sound.

BBE SYSTEM

The BBE system enhances the clarity of high-frequency sound.

Press the BBE button.

Each time it is pressed, the level changes. Select one of the

three levels, or the off position to suit your preference.

.,,, ,,....

.... ......

ma+i3El+EEl+ma

I(cancel)

The T-BASS system enhances the realism of low-frequency

sound.

Press the T-BASS button.

Each time it is pressed, the level changes. Select one of the

three levels, or the off position to suit your preference.

.... ......

+aj!m+tE?iE3+mm3 -+cams

-1

(cancel)

Low-frequency souncl maybe distorted when the T-BASS system

is used for a disc clr tape in which low-frequency sound is

originally emphasized. In this case, cancel the T-BASS system.

SOUND ADJUSTMENT DURING

RECORDING

The output volume and tone of the speakers or headphones

may be freely varied ‘without affecting the level of the recording.

* The BBE system is automatically canceled:

- When the VIDEO 1 (DIGITAL) or VIDEO 2 (DIGITAL) function

is selected

- When the Dolby Pro Logic is turned on

~The BBE system cannot be turned on:

- While the VIDEO 1 (DIGITAL) or VIDEO 2 (DIGITAL) function

is selected

- While the Dolby Pro Logic is turned on

ENGLISH

ELECTRONIC GRAPHIC

EQUALIZER

DSP SURROUND

G:Q

GEQ

This unit provides the following five different equalization modes.

ROCK: Powerful sound emphasizing treble and bass

POP: More presence in the vocals and midrange

JAZZ: Accented lower frequencies for jazz-type music

CLASSIC: Enriched sound with heavy bass and fine treble

BGM: Calm tone with suppressed bass and treble

Press one of the GEQ (Graphic Equalizer) buttons.

The selected mode name appears on the display for four

seconds, and the selected mode on the display is enclosed with

parentheses.

Selected mode

To cancel the selected mode

Press the selected button again. ‘iGEQ OFF appears on the

display.

To select with the remote control

Press the GEQ button repeatedly until the desired equalization

mode is displayed.

The DSP (Digital Signal Processor) surround circuits can recreate

the effect of sounds reflected from walls or ceilings, to obtain

the sound presence of real environments. There are four modes

with matching graphic equalization modes. Equalization modes

are selected automatically and can also be selected or turned

off to suit your preference.

Press one of the DSP buttons (DANCE, LIVE, HALL or

ARENA).

The selected mode name appears on the display for four

seconds, and the selected DSP and matching GEQ modes on

the display are enclosed with parentheses.

Selected DSP mode

Matching GEQ mode

When the music source is monaural

Select LIVE to obtain a simulated stereo effect. When DANCE,

HALL or ARENA is selected, no sound will be heard from the

surround speakers.

To cancel the selected mode

Press the selected button again. “DSP OFF appears on the

display. Even if canceling the selected DSP mode, the matching

or selected GEQ mode still remains.

To select with the remote control

Press the DSP button repeatedly until the desired DSP mode is

displayed.

To adjust the volume and balance of the surround

speakers

Press the MANUAL SELECT button twice to display “SUR OdB

while the DSP system is turned on. Then press the DOWNYor

UPA button repeatedly within four seconds.

● The DSP system is automatically canceled:

- When the Dolby Pro Logic is turned on

- When the “DOLBY DIGITAL SUR or”3 STEREO mode of

the Dolby Digital Surround is selected

● The DSP system cannot be turned on:

- While the “DOLBY DIGITAL SLJR” or “3 STEREO” mode of

the Dolby Digital Surround is selected

- While the Dolby Pro Logic is turned on

- While headphones are plugged in

9 ENGLISH

SELECTION OF AUDIO/VIDEO

SOURCE

DOWNY, UPA

Select the program source.

Press one of the function buttons or the TAPE MONITOR

button.

Radio TUNER

Record PHONO

Television, etc. AUX

I Compact disc I CD

Video VIDEO 1, VIDEO 2, VIDEO 3

LD or Cable TV VIDEO 2

MD or DVD VIDEO 1

The function buttons to be pressed (except PHONO) depend

on the equipment connected to the input terminals on the

rear panel of the unit.

When using a turntable with a built-in equalizer amplifier, set the

switch of the equalizer amplifier to off. See the instructions of

the turntable for further information.

2 Start the selected program source.

3 Adjust the sound.

To change a displayed name for the VIDEO 1 button

and

VIDEO 2 button

When the VIDEO 1 button is pressed, VIDEO 1 is displayed

initially. It can be changed to DVD or MD.

With the power on, press the POWER button while pressing the

VIDEO 1 button.

The displayed name for the VIDEO 2 button can be changeld to

VIDEO 2, LD or TV; with the power on, press the POWER buitton

while pressing the VIDEO 2 button.

To select the “ANALOG” or “DIGITAL” (Dolby Digital

Surround) mode of the VIDEO 1 or VIDEO 2 function

The VIDEO 1 or VIDEO 2 button also works as the DIGITAU

ANALOG selector.

Press the VIDEO ‘1 (VIDEO 2) button and hold it down.

“ANALOG” or “DIGI1-AL” appears on the display one after the

other. Release the button when the desired mode is displayed.

In the DIGITAL modle: Equipment connected to the OPTICAL

DIGITAL IN terminal is selected as a source for the VIDEO 1

button, and one connected to the COAXIAL DIGITAL IN terminal

for the VIDEO 2 button.

In the ANALOG mode: Equipment connected to the VIDEO 1/

DVD/MD IN terminals is selected as a source for the VIDEO 1

button, and one connected to the VIDEO 2/LD/TV terminals for

the VIDEO 2 button.

The “DIGITAL” mode changes to the “ANALOG, ” when pressing

the TAPE MONITOR button.

When the “OVER L.EVEL” indicator lights up

The unit is equipped with the OVER LEVEL indicator. When input

analog signals from the connected equipment are too high to

accept, the indicator lights on the left side of the display. In this

case, adjust the input level as mentioned below so that the

indicator disappears,

To adjust the sound level of the connected source

The input sensitivity level of each function can be adjusted

(excepttheTUNER,

VIDEO 1 (DIGITAL) and VIDEO 2 (DIGITAL)

functions),

When the sound level of the connected source is higher or lower

than that of the TUNIER, adjust it as follows.

About the

video source to the monitor or TV

Selected VIDEO source

Vi: VIDEO 1, V2: VIDEO 2, V3: VIDEO 3

The selected video source is indicated on the display and the

video signal through the MONITOR VIDEO OUT jack is output

on the TV.

Select the function to be adjusted.

Press one of the function buttons or the TAPE MONITOR

button and play the source.

Press the UPA or DOWNY button repeatedly

Adjust the level so that the “OVER LEVEL” indicator does

not light on the display.

● The level can be adjusted between -6d B (M IN) and +i8dB

(MAX) in 2dB steps. Adjust the level so that the sound is

output at the same level as the TUNER.

● The input sensitivity level of the TAPE MONITOR can be

adjusted to OdB or -6dB.

* Before adjusting the level of the TAPE MONITOR, select

the function except TUNER.

ENGL/SH

TO PLAY A DVD OR LD RECORDED IN

DOLBY DIGITAL SURROUND

This receiver is equipped with the Dolby Digital decoder and

has the DIGITAL IN (both OPTICAL and COAXIAL) terminals.

When a DVD or LD player is connected to the DIGITAL IN terminal

of the receiver, you can enjoy theater-quality audio right in your

home when playing discs recorded in Dolby Digital Surround.

Before operation

Check that the TAPE MONITOR is not selected. If the TAPE

MONITOR is selected, press the TAPE MONITOR button so that

“TAPE OFF appears on the display.

Press the VIDEO 1 (VIDEO 2) button and hold it

down until “DIGITAL” is displayed.

The DVD (LD) player connected to the OPTICAL (COAXIAL)

DIGITAL IN terminal is selected as a source.

Start playing the DVD (LD) recorded in Dolby

Digital Surround.

The “DOLBY DIGITAL” indicator will light on the left side of

the display when the bit stream of the Dolby Digital Surround

comes in the unit.

To select the Dolby Digital Surround mode according to your

speakers, see “SELECTING DOLBY SURROUND” on page

14.

● While the TAPE MONITOR is selected and the TAPE MONITOR

indicator turns red, “DIGITAL” cannot be selected.

● When headphones are plugged in, the Dolby Digital Surround

mode is automatically changed to “2CH STEREO and the “2CH

DOWNMIX indicator lights on the display.

Even if the DOLBY SURROUND button is pressed while the

headphones are plugged in, the “DOLBY DIGITAL SUR” or”3

STEREO mode cannot be selected.

● This unit supports input signals of the Dolby Digital Surround

bit stream and linear PCM whose sampling frequency is 32

kHz, 44.1 kHz and 48 kHz. The unit cannot play the DVDS

whose sampling frequency is 96 kHz.

RECORDING AN AUDIO SOURCE

TAPE MONITOR

Select the program source to be recorded.

Press one of the function buttons.

Set the tape deck or MD recorder to the recording

mode.

Start the selected program source.

To monitor recorded sound during recording

(when the

connected tape

deck is a three-head system)

Press the TAPE MONITOR button. “TAPE ON” appears on the

display for four seconds, and then the source name selected in

step 1 comes back on. To cancel the tape monitor, press it again

so that “TAPE OFF appears.

● Any sound control system has no effect on recording (see page

8).

● Input sound through the DIGITAL IN terminals cannot be

recorded. When recording the sound from the DVD or LD player,

connect the analog AUDIO OUT terminals of the player to the

corresponding AUDIO IN terminals of the receiver.

The sound will be recorded in 2 ch stereo.

● When recording sources by the MD recorder connected to the

VIDEO l/DVD/MD AUDIO OUT terminals, select the source

after pressing the VIDEO 2 or VIDEO 3 button (V2 or V3 should

be displayed).

Recording cannot be done while the VI indication is displayed

on the window.

● Input sound from the tape deck connected to the TAPE

MONITOR IN terminals cannot be recorded.

11 ENGLISH

MANUAL TUNING

DIRECT TUNING

MONO

TUNER

Press the TUNER button repeatedly to select the

desired band.

~FM~AM-1

The display changes to frequency indications after indicating

band and video source (VI, V2 or V3) for two seconds.

When the TUNER button is pressed while the power is off,

the power is turned on directly.

Press the UPA or DOWNY button to select a

station.

Each time the button is pressed, the frequency changes.

When a station is received, “TUNE” is displayed for two

seconds. During FM stereo reception, [i@Ill is displayed.

To search for a station quickly (Auto Search)

Keep the UPA or DOWNY button pressed until the tuner starts

searching for a station. After tuning in to a station, the search

stops.

To stop the Auto Search manually, press the

UPA or DOWNY

button.

● The Auto Search may not stop at stations with very weak

signals.

When an FM stereo broadcast contains noise

Press the MONO TUNER button on the remote control so that

“MONO” appears on the display.

Noise is reduced, although reception is monaural.

MONO

To restore stereo reception, press the button so that “MONO”

disappears.

When the reception contains noise interference

Move the unit away from other electrical appliances, especially

digital audio devices, or turn off the appliances that generate

noise signals.

POWER

1,2

DOWNY, UPA

When you know the frequency of the desired station, you can

tune in directly to the station.

1 Press the TUNER button to select a band.

2 Press the TUNER button and hold it down until

“

“flashes

011 the display (Direct Tuning Modle)......

3 Press the appropriate numbered buttons to tume

in to the desired station.

Example:

To tune in to 106,50 MHz, press the 1, 0, 6, 5 and O buttcms.

To tune in to 95.20 MHz, press the 9, 5, 2 and Q buttons.

To cancel the Direct tuning mode

Press the UPA or DOWNV button.

● When entering a frequency out of tuning range, the value

flashes for two seconds and then goes off. Check the frequency

and repeat step 3 correctly.

● When entering a frequency not covered by the tuning interval,

the value is automatically rounded up or down to the closest

one covered by it.

● The DIGIT buttons cm the remote control can not be l~sed when

tuning in to the desllred station.

To change the AM tuning interval

The default setting ofthe AM tuning interval is

10 kHz/step If

you use this unit in an area where the frequency allocation

system is 9 kHz/step, change the tuning interval.

Hold down the TUNER button and press the POWER button

immediately. Note that the unit is set to the Direct Tuning mode

if the TUNER button is pressed and held down for about haLf

a second.

To reset the interval, repeat this procedure.

ENGLISH 12

PRESETTING STATIONS

PRESET NUMBER TUNING

)

The unit can store a total of 32 preset stations. When a station is

stored, a preset number is assigned to the station. Use the preset

number to tune in to a preset station directly.

Press the TUNER button to select the band, and

press the UPA or DOWN7 button to select a

station. Direct tuning is also available.

Press the SET button to store the station.

A preset number assigned to the station, beginning from 1 in

consecutive order for each band, flashes in the display for

two seconds.

Repeat steps 1 and 2.

No more stations will be stored if a total of 32 stations have

already been stored for all the bands.

1 Press the TUNER button to select a band.

2 Press the numbered buttons to select a preset

number.

Example:

To select preset number 25, press 2 and 5.

To select preset number 7, press O and 7.

To clear a preset station

Select the preset numberof

the stationto be cleared.Then, press

the SET button, and press the

SET button again within four

seconds.

The preset numbers of all other stations in the band with higher

numbers are decreased by one.

When using the remote control

Press UP M or DOWN W button to select a preset number.

The DIGIT buttons on the remote control can not be used when

selecting a preset number.

When the AM tuning interval is changed, all preset stations are

cleared. The preset stations have to be set again.

13 ENGLISH

This unit is equipped with not only the Dolby Pro Logic decoder

but also Dolby Digital decoder.

The unit and the center and surround speakers (standard) assure

full-scale home theater sound. When playing back discs or video

software that have been recorded in Dolby Pro Logic or Dolby

Digital Surround, astonishingly realistic sound surrounds the

listener to create a new level of audio/visual entertainment.

Independent control of the five channels allows the listener to

enjoy the same type of sound reproduction experienced in movie

theaters. Voices are reproduced in the front and center sound

field, while ambient sounds like cars and crowds are reproduced

on all sides of the listener for an incredibly lifelike audio/video

experience. Please read the following carefully to “tune” the

system’s output to match the characteristics of your listening

space.

Check the following:

● Before enjoying the DOLBY SURROUND sound, adjust the

speaker sound levels to the proper balance (see page 15).

● Make sure the speakers are properly connected and positioned

(see pages 4 and 5).

● Make sure the TV set and video unit are properly connected

(see page 3).

● Make sure the disc and video tape, etc., support Dolby Pro

Logic or Dolby Digital Surround.

SELECTING DOLBY SURROUND

The optimal Dolby Digital Surround and Dolby Pro Logic modes

and settings depend on the type and placement of the speakers.

Check the current type and placement of your speakers and

select the recommended mode accordingly.

The recommended mode

[Dolby Digital Surround]

Center s~eaker

/ Lamer-size I Srnalier-size I NOs~eaker I

Surround speaker DOLBY DIGITAL DOLBY DIGITAL DOLBY DIGITAL

(Rear speaker)

SUR-WIDE

SUR-NORMAL SUR-PHANTOM

I I

No surround

3 STEREO- 3 STEREO-

2CH STEREO

speaker WIDE

NORMAL

[Dolby Pro Logic]

Center speaker

LOGIC-WIDE LOGIC-NORMAL LOGIC-PHANTOM

PHANTOM mode: Select this mode when the center speaker is

not connected. All center channel signals are redistributed to

the left and rightchannel speakers.

3 STEREO mode:

Select this mode when the surround speakers

TO SELECT A,DOLBY SURROUND MODE

1,2

Preparations

When selecting a Dolby Digital Surround mode, select the

VIDEO 1 (DIGITAL) or VIDEO 2 (DIGITAL) function (see page

11) and play

a disc recorded in Dolby Digital Surround

before selecting the mode.

● When selecting a lDolby Pro Logic mode, select the function

except VIDEO 1 (DIGITAL) and VIDEO 2 (DIGITAL).

1 Press the DOLBY SURROUND button repeatedly

to select the appropriate mode.

The selected mode name runs through on the display.

Each time the button is pressed, the mode changes as follows:

[Dolby Digital Surround]

* DOLBY DIGITAL SUR

2CH STEREO ~

,STEREO+-]

❑

Lmm

Select the Dolby Digital Surround mode after playing a source

recorded in Dolby Digital Surround.

The Dolby Digital Surround mode cannot be selected:

● When using the unit for the first time

● After playing discs not recorded in Dolby Digital Surround.

[Dolby Pro Logic]

When selecting the DOLBY PRO LOGIC or 3 STEREO mode

of the Dolby Pro Logic, the DOLBY PRO LOGIC indicator

lights on the left side of the display.

DOLBY PRO LOGIC~ 3 STEREO -

~ DOLBY PRO LOGIC OFF(cancel) ~J

To be contirwed

are not connected.

ENGLISH 14

2 Press the DOLBY SURROUND button again and

hold it down until the center speaker mode to be

selected appears.

When selecting the DOLBY DIGITAL SUR or DOLBY PRO

LOGIC mode in step 1:

“NORMAL;

“WIDE and “PHANTOM” appear in turn.

When selecting the 3 STEREO mode

in step 1:

“NORMAL’ and “WIDE appear one after the other.

● Depending on the sound source or listening condition, surround

effect may not be obtained even when the Dolby Digital

Surround or Dolby Pro Logic is selected.

● The full Dolby Digital Surround or Dolby Pro Logic effect cannot

be obtained when using software not recorded in the Dolby

Digital Surround or Dolby Pro Logic system. In this case, use

the DSP surround system instead (see page 9).

● When headphones are plugged in:

- The Dolby Pro Logic system is automatically canceled.

- The Dolby Digital Surround mode is automatically changed

to “2CH STEREO.”

● While headphones are plugged in:

- The Dolby Pro Logic cannot be turned on.

- The “DOLBY DIGITAL SUR” or “3 STEREO mode of the

Dolby Digital Surround cannot be selected.

ADJUSTING SPEAKER LEVEL

BALANCE

214

2,4

“UPPM,

DOWNM

The unit is equipped with a built-in test signal generator called a

noise sequencer for easy balance adjustment of all five channels.

The sequencer outputs a noise signal that “travels” from channel

to channel, enabling the simple adjustment of sound level to

achieve the same apparent loudness, at your listening position,

from each channel.

Select the Dolby Digital Surround (except “2CH

STEREO”) or Dolby Pro Logic mode according

to the current type and placement of your

speakers.

(See page 14.)

Press the MANUAL SELECT button and hold it

down for about two seconds until “L/R OdB”

appears.

A noise signal is sent to each channel in turn as follows:

DOLBY DIGITAL SUR (DOLBY PRO LOGIC) NORMAL

or WIDE mode

L/R OdB (Left front speaker)*

CEN OdB(Center speaker)

UR ~dB (Right front speaker)*

S-R OdB (Right surround speaker)

S-L OdB (Left surround speaker)

15 ENGLISH

——.

—...—.-. —. —..—

DOLBY DIGITAL SUR (DOLBY PRO LOGIC) PHANTOM

mode

L/R OdB*+ L/R OdB’

S-L OdB~S-R OdB

DOLBY DIGITAL SUR (DOLBY PRO LOGIC) 3 STEREO

NORMAL or WIDE mode

~ UR OdB’+CE

N OdB+ UR OdB*

‘ “L” or “R” flashes to indicate one of the front speakers from

which the noise signal is output,

Adjust the sound level of the center and surround

speakers.

While “CEN, ” ‘(S-P’ or “S-R flashes in the display, press the

UPA or DOWN7 button so that the sound level of the center

or surround speakers matches that of the front speakers,

The balance of the front speakers can be adjusted as well

while

“L/R is displayed.

Press the MANUAL SELECT button again to stop

the noise signal.

● The UPMM or DOWN 14< button on the remote control cannot

be used in step

3 when adjusting the speaker balance with the

noise signals.

* When adjusting the speaker level balance of the Dolby Digital

Surround, that of the Dolby Pro Logic is also changed and vice

versa.

About the channels

The left and right speakers create the stereo effect.

The center speaker helps achieve precise sound positioning

over a broad sound field,

The rear-mounted surround speakers enhance the “depth” of

the sound field,

To change the delay time of the surround speakers or

center speaker when using the Dolby Digital Surround

or Dolby Pro Logic mode

While the Dolby Digital Surround (except “2CH STEREO”) or #

Dolby Pro Logic is activated, press the MANUAL SELE:CT button

repeatedly so that “CEN OmS” or “SUR 5mS” (SUR 20mS) is

displayed. Then, press the UPA or DOWN7 button withlln 4

seconds. Each time it is pressed, the delay time changes as

shown below.

[Center speaker]

,,,,

Adjust the delay time so that lines

(voice in a movie) are heard

clearly and naturally,

The center speaker delay time is initially set to O ms

(milliseconds). It can be adjusted between O and 5 rns in 1 ms

step.

LOms ++1 ms ++ 2ms _ 3ms _ 4ms _ 5ms J

[Surround speakers]

Adjust the delay time to suite your preference,

Dolby Digital Surround

The speakers delay time is initially set to 5 ms. It can be adjusted

between O and 15 ms in 5 ms steps.

Dolby Pro Logic

The speakers delay time is initially set to 20 ms. It can be adjusted

between 15 and 30 ms in 5 ms stetx.

❑

● When adjusting the delay time of the surround speakers or

center speaker for Ihe Dolby Digital Surround, that of the Dolby

Pro Logic is changed and vice versa.

● When the surround speakers delay time of the Dolby Digital

Surround is set to (0ms (5 ms, 10 ms , or 15 ins), that of the

Dolby Pro Logic is set to 15 ms (20 ms, 25 ms or 30 ins), and

vice versa,

To adjust the speaker level balance while listening to the

source

The speaker level balance can be changed after adjustingitwith

the noise sequencer. The balance can be changed whenever

the Dolby Digital Surround or Dolby Pro Logic system is activated,

Play a disc or video software recorded in Dolby Pro Logic or

Dolby Digital Surround.

Press the MANUAL SELECT button repeatedly so that “l./R,”

“CEN; “S-U or “S-R” appears on the display.

Press the UPA c)r DOWNY button while the speaker name

to be adjusted is displayed.

In this case, the lJP-I or DOWNW< button on the remote

control can be used as well.

ENGLISH 161

ADJUSTING DOLBY DIGITAL

SURROUND SOUND

MANUAL

SEL/Z2T

DOWN

UP-

ADJUSTING LOW FREQUENCY SOUND

EFFECT(LFE)

The disc recorded in Dolby Digital Surround contains special

signals called LFE to enhance low frequency sound effect. The

LFE signals are recorded in some particular parts on the disc

and output from the connected sub-woofer to reproduce

astonishingly powerful low sound.

The sound level of the LFE signals can be adjusted according to

your speakers connected while the Dolby Digital Surround is

activated.

Press the

UPA or DOWNT button and hold it

down until “LFE” is displayed.

Press the UPA or DOWNY button repeatedly to

adjust the LFE level.

The unit is initially set to OdB (maximum) and can be adjusted

as shown below.

OFF _ -20dB _ -lOdB _

OdB

When not using a sub-woofer

While the Dolby Digital Surround (except “2CH STEREO”) is

activated, press the MANUAL SELECT button once so that

“SUBW ON” is displayed. Then, press the

UPA button within 4

seconds to display “SUBW OF F.” The LFE signals are

redistributed to the other speakers.

To restore, press the MANUAL SELECT button once so that

“SUBW OFF is displayed, then press the DOWNV button to

display “SUBW ON.”

When setting the sub-woofer mode of the Dolby Digital Surround

to “SUBW OFF: that of the Dolby Pro Logic is also set to “SUBW

OFF: and vice versa. In this case, the sub-woofer signals are

redistributed to the other speakers.

ADJUSTING DYNAMIC RANGE

Dynamic range of the Dolby Digital Surround sound can be

adjusted. The unit is initially set to the “STD” (standard) mode.

1 While the Dolby Digital Surround is activated,

press the SET button and hold it down until “MID

NIGHT THEATER” runs through on the display.

2 Press the UPA or DOWNY button to select the

“MAX;’ “STD” or “MIN” mode.

MIN _ STD ~ MAX

[MIN]

Youcan enjoy the full dynamic range sound like in the movie

theater,

[STD]

Original position, when playing back in home, that is

recommended by the software producers.

[MAX]

Select this mode when playing back at low volume. This is

the mode when playing back in the mid night.

17 ENGLISH

OPERATING TV, CABLE TV, VCR

AND CD PLAYER

To confirm the stored ID code

You can check the stored ID code by counting the indicator

blinking.

You can control basic functions of a TV, CABLE TV, VCR and

CD player with this remote control.

TO ENTER THE ID CODE OF THE

EXTERNAL EQUIPMENT

Indicator

MODE SELECT

DIGIT buttons

(o-9)

SET UP

Before attempting to control them, be sure to enter the ID code

of the external equipment to the remote control as follows.

Confirm the code number of the external

equipment.

See

the ID code list in the “APPENDIX’ at the end of this

manual,

Press either the TV, CABLE, VCR or CD button in

the MODE SELECT area.

Press and hold the SET UP button for about 2.5

seconds.

Confirm that the indicator blinks twice while pressing the SET

UP button.

Press three DIGIT buttons which correspond to

the ID code of the external equipment.

For example, if your CD player is an AIWA unit, the required

ID code is 124 or 157. In this case, press the DIGIT buttons

in the order of”1 ,“ “2 and “4” (or “1 ,“ “5” and “7” ).

After the third DIGIT button is pressed, the indicator blinks

twice indicating that the ID code is correct and is stored on

the remote control.

Press either thelW, CABLE, VCR or CD button.

For example, to check the stored code for CD player, press

CD.

Press and hold the SET UP button for about 2.5 seconds.

Press “9/’ “9” and “O.”

Press “1;’ and count the indicator blinks.

For example, in the case that the stored ID is “1 57.”

The indicator blinks once.

Press “2;’ and count the indicator blinks.

The indicator blinks five times,

Press “3;’ and count the indicator blinks.

The indicator blinks seven times,

TO CONTROL TV, CABLE TV, VCR AND CD

PLAYER

VOLUME

DIGIT buttons

(O-9) and ENTER

MODE SELECT -

VCRICD

lfl:Pause, U: Stop,

POWER -

M: Rewind,

-: Play,

W :Fast forward

❑

Press any button in the MODE SELECT area (TV,

CABLE, VCR or CD).

The remote control is ready to operate the selected mode

equipment.

Press one of the buttons indicated above.

For the use of the O – 9 and the ENTER buttons, see the

instruction manual supplied with the unit to be controlled.

Other buttons indicated above have the same function which

you will find on the unit to be controlled.

● Reenter the ID CODE of the external equipment after replacing

the batteries of the remote control.

● [f there are plural ID codes for external equipment in the

“APPENDIX,” try each number listed until you can control the

external equipment.

ENGLISH 18

ON SCREEN DISPLAY

SETTING THE SLEEP TIMER

The receiver provides an “On

Screen Display” function to show

the receiver settings on the TV screen. With the TV turned on,

when you operate the receiver buttons or remote control buttons,

the settings appear on the TV screen as well as the receiver

display. The following are examples of the “On Screen Display.”

When turning on the receiver, pressing the function

buttons, or tuning in a station

On the right side of the screen, the setting results appear for 5

MdN VIDEO 1

AUJOFM

TAPE OFF

{

MUT;;G

TUNER FREQ

87,50 MHz

VOL 10

“MUTING ON” continues flashing

until MUTING mode is set to off.

When m’essina audio effect buttons such as DOLBY

SURROUND, &P, GEQ, T-BASS, BBE and MANUAL

SELECT

On the left side of the screen, the audio effect settings appear

for 5 seconds.

PRO LOGICO:;F

DSP

LVL

MAX

LVL

MAX

GEQ OFF

T-BASS

OFF

BBE

OFF

When pressing CLOCK or SLEEP buttons on the remote

controi

On the left side of the screen, the timer setting and the present

time appear for 5 seconds.

The receiver provides an “On Screen Display” function only when

the TV is connected to the MONITOR VIDEO OUT jack.

UPA, ~OWN7

The receiver can be automatically turned off at a specified time.

1 Press the AIWA RECEIVER button.

2 Press the SLEEP button.

The unit will be turned off after about 60 minutes.

specify the time until the power is turned off

Press the UPA

or DOWNV button on the main unit repeatedly

within four seconds after step 2.

Each time the button is pressed, the time changes between 5

and 240 minutes in 5-minute steps.

Specified time

To check the time remaining until the power is turned off

Press the SLEEP button once. The remaining time is displayed

for four seconds.

To cancei the sleep timer

Press the SLEEP button twice so that “SLEEP on the display

disappears.

The UP- or DOWNW button on the remote control cannot

be used to specify the time until the power is turned off. Use the

buttons on the main unit.

19 ENGLISH

La page charge ...

Aiwa AV-DV70 Operating Instructions Manual

Marque: Aiwa

Modèle: AV-DV70

Catégorie: Récepteurs AV

Taper: Operating Instructions Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Aiwa AV-DV70
español: Aiwa AV-DV70

Aiwa AV-DV70 Operating Instructions Manual

Aiwa AV-DV70 Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents