ECOVACS DEEBOT N8 Pro+ Le manuel du propriétaire

Catégorie
Aspirateurs robotiques
Taper
Le manuel du propriétaire
Instruction Manual/Bedienungsanleitung/Manual de instrucciones/
Manuel d'instructions/Manuale d'uso/Руководство по эксплуатации/
Instrukcja obsługi/Gebruiksaanwijzing
2
EN
Important Safety Instructions
1. This Appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the Appliance in a safe way
and understand the hazards involved. Children shall not
play with the Appliance. Cleaning and user maintenance
shall not be made by children without supervision.
2. Clear the area to be cleaned. Remove power cords
and small objects from the oor that could entangle
the Appliance. Tuck rug fringe under the rug base, and
lift items such as curtains and tablecloths off the oor.
3. If there is a drop off in the cleaning area due to a step
or stairs, you should operate the Appliance to ensure
that it can detect the step without falling over the
edge. It may become necessary to place a physical
barrier at the edge to keep the unit from falling. Make
sure the physical barrier is not a trip hazard.
4. Only use as described in this manual. Only use
attachments recommended or sold by the manufacturer.
5. Please make sure your power supply source voltage
matches the power voltage marked on the Auto-
Empty Station.
6. For INDOOR household use ONLY. Do not use
the Appliance in outdoor, commercial or industrial
environments.
7. Use only the original rechargeable battery and Auto-
Empty Station provided with the Appliance from
the manufacturer. Non-rechargeable batteries are
prohibited. For battery information, please refer to
Specications section.
8. Do not use without dust bin and/or lters in place.
9. Do not operate the Appliance in an area where there
are lit candles or fragile objects.
10. Do not use in extremely hot or cold environments
(below -5˚C/23˚F or above 40˚C/104˚F).
11. Keep hair, loose clothing, ngers, and all parts of
body away from any openings and moving parts.
12. Do not operate the Appliance in a room where an
infant or child is sleeping.
13. Do not use Appliance on wet surfaces or surfaces
with standing water.
14. Do not allow the Appliance to pick up large objects
like stones, large pieces of paper or any item that
may clog the Appliance.
15. Do not use Appliance to pick up ammable or
combustible materials such as gasoline, printer or
copier toner, or use in areas where they may be present.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical Appliance, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE
SAVE THESE INSTRUCTIONS
3
EN
16. Do not use Appliance to pick up anything that is
burning or smoking, such as cigarettes, matches,
hot ashes, or anything that could cause a re.
17. Do not put objects into the suction intake. Do not use
if the suction intake is blocked. Keep the intake clear
of dust, lint, hair, or anything that may reduce air ow.
18. Take care not to damage the power cord. Do not pull
on or carry the Appliance or Auto-Empty Station by
the power cord, use the power cord as a handle, close
a door on the power cord, or pull power cord around
sharp edges or corners. Do not run Appliance over the
power cord. Keep power cord away from hot surfaces.
19. If the power cord is damaged, it must be replaced
by the manufacturer or its service agent in order to
avoid a hazard.
20. Do not use with a damaged power cord or receptacle.
Do not use the Appliance or Auto-Empty Station if it
is not working properly, has been dropped, damaged,
left outdoors, or come in contact with water. It must
be repaired by the manufacturer or its service agent in
order to avoid a hazard.
21. Do not use with a damaged power cord or receptacle.
Do not use the Appliance or Auto-Empty Station if it
is not working properly, has been dropped, damaged,
left outdoors, or come in contact with water. It must
be repaired by the manufacturer or its service agent in
order to avoid a hazard.
22. Turn OFF the power switch before cleaning or
maintaining the Appliance.
23. The plug must be removed from the receptacle before
cleaning or maintaining the Auto-Empty Station.
24. Remove the Appliance from the Auto-Empty
Station, and turn OFF the power switch to the
Appliance before removing the battery for disposal
of the Appliance.
25. The battery must be removed and discarded
according to local laws and regulations before
disposal of the Appliance.
26. Please dispose of used batteries according to local
laws and regulations.
27. Do not incinerate the Appliance even if it is severely
damaged. The batteries can explode in a re.
28. When not using the Auto-Empty Station for a long
period of time, please unplug it.
29. The Appliance must be used in accordance with
the directions in this Instruction Manual. ECOVACS
ROBOTICS cannot be held liable or responsible for
any damages or injuries caused by improper use.
30. The robot contains batteries that are only
replaceable by skilled persons. To replace the
robot’s battery, please contact Customer Service.
31. If the robot will not be used for a long time, power OFF
the robot for storage and unplug the Auto-Empty Station.
32. WARNING: For the purposes of recharging the
battery, only use the detachable supply unit
CH1918 provided with the Appliance, or CH1822
sold separately as an accessory.
4
EN
To satisfy RF exposure requirements, a separation
distance of 20 cm or more should be maintained between
this device and persons during device operation.
To ensure compliance, operations at closer than this
distance is not recommended. The antenna used for this
transmitter must not be co-located in conjunction with any
other antenna or transmitter.
To disable Wi-Fi module on DEEBOT, power the robot ON.
Place the robot on the Auto-Empty Station making sure
the Charging Contacts on DEEBOT and the Auto-Empty
Station Pins make a connection.
Press and hold the AUTO Mode Button on the robot for
20 seconds until DEEBOT emits 3 beeps.
To enable Wi-Fi module on DEEBOT, power the robot OFF
and then power ON. The Wi- Fi module is turned on when
DEEBOT is restarted.
Correct Disposal of this Product
This marking indicates that this product should not be
disposed of with other household waste throughout
the EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material
resources. To recycle your used device, please use the
return and collection systems or contact the retailer where
the product was purchased. They can safely recycle this
product.
For EU Countries
Class II
Short-circuit-proof safety isolating
transformer
Switch mode power supply
For indoor use only
Direct current
Alternating current
For EU Declaration of Conformity information, visit https://
www.ecovacs.com/global/compliance
5
EN
Package Contents
Robot Auto-Empty Station
Instruction Manual Side Brushes
Mopping Pad Plate
Washable Mopping
Pad
Disposable
Mopping Pads
Note: Figures and illustrations are for reference only and may differ
from actual product appearance.
Product design and specications are subject to changes without
notice.
Power Cord
Dust Bag
Product Diagram
Robot
AUTO Mode Button
Top Cover
TrueMapping
Distance Sensor
Anti-collision Bumper
TrueDetect
3D Sensor
6
EN
Wi-Fi Indicator
Light
RESET Button
Power Switch
Multi-function
Cleaning Tool
Auto-Empty Dust Bin
Dust Bin Handle
Release Button
Filter Net
Auto-Empty Outlet
Sponge Filter
High Efciency Filter
Charging Contacts
Anti-drop Sensors
Reservoir
Main Brush
Release Button
Universal Wheel
Side Brushes
Water Outlet
Anti-drop Sensors
Driving Wheels
Main Brush
Carpet Detection
Sensor
Bottom View
7
EN
Auto-Empty Station
Lid Release Button
Indicator Light
Infrared Singnal Emitter
Auto-Empty Inlet
Auto-Empty Station Pins
Auto-Empty Station (Back)
Power Cord Port
Power Cord Wrap
Auto-Empty Station (Top)
Dust Bag Socket
Dust Evacuation Tube
Blower Cover
Auto-Empty Station (Bottom)
Base Screw Socket
Dust Evacuation Tube
+ Tube Cover
Ramp Extension Slot
Dust Evacuation Tube
Cover Set Screws
8
EN
Reservoir
Water Inlet
Mopping Pad
Water Inlet Cover
Reservoir Release
Button
Mopping Pad Plate
Power Cord
Notes Before Cleaning
Tidy up the area to be cleaned by
putting furniture, such as chairs,
in their proper place.
During the rst use, make sure
each room door is open to help
DEEBOT fully explore your house.
It may be necessary to place a
physical barrier at the edge of a
drop to stop the unit from falling
over the edge.
Put away objects including cables, cloths and slippers, etc.
on the oor to improve the cleaning efciency.
Before using the product on a rug with tasseled edges,
please fold the rug edges under.
Please do not stand in narrow spaces, such as hallways, and
make sure not to block the LDS Laser Distance Sensor.
9
EN
Quick Start
1
Remove Protective Materials
2
Assemble Auto-Empty Station
3
Install Side Brushes
Click
10
EN
Charging DEEBOT
1
Auto-Empty Station Placement
2
Power ON
Note: I = ON, O = OFF.
DEEBOT cannot be charged
when being powered OFF.
6.5
3
Charge DEEBOT
Empty remaining water from
the Reservoir and remove the
Reservoir and the mopping pad
plate before charging DEEBOT.
ashes when DEEBOT is
charging. goes out when
DEEBOT is fully charged.
ECOVACS HOME
ECOVACS HOME App
To enjoy all available features, it is recommended to control your
DEEBOT via the ECOVACS HOME app.
Wi-Fi Indicator Light
Before you start, make sure that:
Tips: If you have any problems during the Wi-Fi setup process, refer
to the Troubleshooting > Wi-Fi Connection section in this manual.
• Your mobile phone is connected to a Wi-Fi network.
• The 2.4GHz band wireless signal is enabled on your router.
• The Wi-Fi indicator light on DEEBOT is slowly ashing.
Slowly flashing
Disconnected to Wi-Fi or
waiting for Wi-Fi connection
Rapidly flashing Connecting to Wi-Fi
Solid Connected to Wi-Fi
11
EN
*
When Auto-Empty Station is connected
to power, DEEBOT automatically
returns to the station to charge and
empty the Dust Bin as it needs.
1
3
Operating DEEBOT
During the rst cleaning, please supervise DEEBOT and assist it should
there be a problem.
Pressing for 3 seconds to send
DEEBOT back to the Auto-Empty Station.
Start
2
Pause
Return to Charge
Note: The robot’s Control Panel stops
glowing after the robot is paused for
a few minutes. Press the AUTO Mode
Button on DEEBOT to wake up the robot.
1
2
OZMO Mopping System
Note: To prolong the service life of the reservoir, it is recommended
to use puried water or softened water for OZMO mopping system.
OR
Note: When DEEBOT is mopping, DEEBOT automatically detects
the carpet and keeps away from it. If you need to clean the carpet,
please uninstall the mopping pad plate rst.
Click
12
EN
To keep DEEBOT running at peak performance, perform maintenance tasks and replace parts with the following frequencies:
A multi-function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
Note: ECOVACS manufactures various replacement parts and ttings. Please contact Customer Service for more information on replacement parts.
Robot Part Maintenance Frequency Replacement Frequency
Disposable Mopping Pad / Replace after each use
Washable Mopping Pad After each use Every 50 washes
Dust Bag /
Dust Bags should be replaced when prompted by
the Indicator Light/ECOVACS HOME App.
Reservoir/Mopping Pad Plate After each use /
Side Brush Once every 2 weeks Every 3-6 months
Main Brush Once per week Every 6-12 months
Sponge Filter/ High Efciency Filter Once per week Every 3-6 months
TrueDetect 3D Sensor
Universal Wheel
Anti-Drop Sensors
Bumper
Charging Contacts
Auto-Empty Station Pins
Once per week /
Regular Maintenance
Before performing cleaning and maintenance tasks on DEEBOT, turn the robot OFF and unplug the Auto-Empty Station.
13
EN
OZMO Mopping System
1 2
Washable Mopping Pad
Disposable Mopping Pad
Clean the water inlet filter on the
bottom of the Reservoir if it is clogged.
14
EN
3 3
11
2 2
4
5
Auto-Empty Dust Bin and Filters
Dust Bin Filter
15
EN
Auto-Empty Station
Auto-Empty Station Pins
Infrared Signal Emitter
Note: Before performing cleaning and maintenance on Auto-Empty
Station, unplug it rst.
* For a proper maintenance, wipe with a clean dry cloth, and avoid
using any detergent or cleaning spray.
Main Brush and Side Brushes
Main Brush
Side Brushes
16
EN
Dust Bag
1
* The Dust Bag will be sealed by the handle so the dust will not leak.
Dispose the Dust Bag
2
Clean the Blower Cover
3
Install the Dust Bag
4
Close the Dust Container Lid
17
EN
Close the Dust Container Lid
Dust Evacuation Tube
Unscrew the Dust Evacuation
Tube Cover
Uninstall the Dust Evacuation
Tube Cover
Clean the Dust Evacuation
Tube
Other Components
Note: Before cleaning the robot’s Charging Contacts and Auto-Empty
Station Pins, turn the robot OFF and unplug the Auto-Empty Station.
18
EN
Storage
If DEEBOT will not be used for a while, fully charge DEEBOT and power
OFF before storage. Charge DEEBOT every 1.5 month to prevent battery
drain.
Note: When DEEBOT is not cleaning, it is recommended to keep
DEEBOT powered ON and charging.
Indicator Light
DEEBOT will tell you something is wrong with an indicator light
and voice report. More detailed support is available through the
ECOVACS HOME and online website.
Indicator Light Scenario
AUTO Mode Button glows a
solid WHITE.
The robot is cleaning.
The robot is paused while cleaning.
AUTO Mode Button ashes
WHITE.
The robot is charging.
The robot is starting.
The robot is relocating.
AUTO Mode Button glows a
solid RED.
The robot has low battery.
AUTO Mode Button ashes
RED.
The robot has a problem.
19
EN
No. Problem Possible Causes Solutions
1 DEEBOT is not charging.
DEEBOT is not switched ON. Switch ON DEEBOT.
DEEBOT has not connected to the Auto-
Empty Station.
Be sure that the robot’s Charging Contacts have
connected to the Auto-Empty Station Pins.
The Power Cord is not connected to the
Auto-Empty Station.
Make sure the Power Cord is rmly connected to the
Auto-Empty Station.
The Auto-Empty Station is not connected to
the power supply.
Make sure the Auto-Empty Station is connected to the
power supply.
The battery is completely discharged. Please contact Customer Care for help.
2
DEEBOT cannot return to the
Auto-Empty Station.
The Auto-Empty Station is not correctly connected.
Make sure the Auto-Empty Station is correctly connected.
The Auto-Empty Station is manually moved
during the cleaning.
It is suggested not to move the Auto-Empty Station
during the cleaning.
DEEBOT is paused for more than 90 minutes.
It is suggested not to pause DEEBOT for more than 90
minutes.
DEEBOT did not start cleaning from the Auto-
Empty Station.
Make sure DEEBOT starts cleaning from the Auto-Empty
Station.
3
DEEBOT gets stuck while
working and stops.
DEEBOT is tangled with something on the
oor (electrical wires, curtains, carpet
fringing, etc.).
DEEBOT will try various ways to free itself. If it is
unsuccessful, manually remove the obstacles and restart.
DEEBOT might be stuck under furniture with
an entrance of similar height.
Please set a physical barrier, or set a Virtual Boundary in
the ECOVACS HOME App.
Troubleshooting
20
EN
No. Malfunction Possible Causes Solutions
4
DEEBOT returns to the Auto-
Empty Station before it has
nished cleaning.
Working time varies according to oor
surface, room complexity and the Cleaning
Mode selected. When the battery gets low,
DEEBOT automatically switches to Recharge
Mode and returns to the Auto-Empty Station
to recharge itself.
Turn on Continuous Cleaning function in ECOVACS
HOME App. DEEBOT will automatically resume the
uncompleted cleaning cycle when Continuous Cleaning
is enabled.
DEEBOT is unable to reach certain areas
blocked by furniture or barriers.
Tidy up the area to be cleaned by putting furniture and
small objects in their proper place.
The Auto-Empty Station is too distant from
the center of the house.
Please place the Auto-Empty Station against the wall of a
central room of the house.
5
DEEBOT does not clean
automatically at the scheduled
time.
Time Scheduling function is cancelled.
Program DEEBOT to clean at specic times using the
ECOVACS HOME App.
DEEBOT is switched OFF. Switch ON DEEBOT.
The robot’s battery is low.
Keep DEEBOT switched ON and connected to the Auto-
Empty Station to make sure it has a full battery to work at
any time.
6
The water is not coming out of
the Reservoir when DEEBOT is
mopping.
The water inlet lter on the bottom of
Reservoir is clogged.
Unscrew the water inlet on the bottom of Reservoir and
clean the lter.
The Reservoir runs out of water. Add water into the Reservoir.
The water outlets on the bottom of DEEBOT
are clogged.
Check the water outlets on the bottom and clean.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200

ECOVACS DEEBOT N8 Pro+ Le manuel du propriétaire

Catégorie
Aspirateurs robotiques
Taper
Le manuel du propriétaire