Extron FOX3 Matrix 80x Manuel utilisateur

User Guide

Fiber Optic Matrix Switchers

68-2987-01 Rev. B

06 20

FOX3 Matrix Series

Conﬁgurable Fiber Optic Digital Matrix Switcher

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended

to alert the user of the presence of uninsulated dangerous voltage

within the product’s enclosure that may present a risk of electric

shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)

instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide, part number 68-290-01, on the Extron

website, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses

Produktes gefährliche Spannungen herrschen, die nicht isoliert sind

und die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige

Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,

EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in

den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer

68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro

del producto, lo que puede representar un riesgo de descarga

eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de importantes instrucciones de uso y

mantenimiento recogidas en la documentación proporcionada con el

equipo.

Para obtener información sobre directrices de seguridad, cumplimiento

de normativas, compatibilidad electromagnética, accesibilidad y temas

relacionados, consulte la Guía de cumplimiento de normativas y seguridad

de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

avertissement : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur la présence à l’intérieur du boîtier du produit

d’une tension électrique dangereuse susceptible de provoquer un

choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur des instructions d’utilisation ou de

maintenance importantes qui se trouvent dans la documentation

fournie avec le matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la

réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets

connexes, lisez les informations de sécurité et de conformité Extron, réf.

68-290-01, sur le site Extron, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di tensione non isolata pericolosa

all’interno del contenitore del prodotto che può costituire un rischio di

scosse elettriche.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad avvertire

l’utente della presenza di importanti istruzioni di funzionamento e

manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative,

compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento

alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo

68-290-01, sul sito web di Extron, www.extron.com.

I

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан

на продукте, предупреждает пользователя о наличии

неизолированного опасного напряжения внутри корпуса

продукта, которое может привести к поражению

электрическим током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций

по эксплуатации и обслуживанию в руководстве,

прилагаемом к данному оборудованию.

Для получения информации о правилах техники безопасности,

соблюдении нормативных требований, электромагнитной

совместимости (ЭМП/ЭДС), возможности доступа и других

вопросах см. руководство по безопасности и соблюдению

нормативных требований Extron на сайте Extron: ,

www.extron.com, номер по каталогу - 68-290-01.

安全说明 • 简体中文

警告：产品上的这个标志意在警告用户该产品机壳内有暴露的危险电压，

有触电危险。

注意：产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍

使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01。



Copyright

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (

®

), registered service marks (

SM

), and trademarks (

TM

) are the property of RGBSystems, Inc. or

ExtronElectronics (see the current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

®

)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Glitch Free, Global

Configurator, GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink,

MediaPort, NAV, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount,

SpeedSwitch, StudioStation, SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall,

XPA, XTP, XTPSystems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-RATEFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, AVEdge, CableCover, CDRS(ClassD

Ripple Suppression), Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator,

DSPConfigurator, DSVP(Digital Sync Validation Processing), eLink, EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk,

MAAP, MicroDigital, Opti-Torque, PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope-Trigger,

SIS, SimpleInstructionSet, Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference. This interference must be corrected at the expense of the user.

NOTE: For more information on safety guidelines, regulatory compliances, EMI/

EMF compatibility, accessibility, and related topics, see the “Extron Safety and

Regulatory Compliance Guide” on the Extron website.

Battery Notice

This product contains a battery. Do not open the unit to replace the battery. If the

battery needs replacing, return the entire unit to Extron (for the correct address, see the

Extron Warranty section on the last page of this guide).

CAUTION: Risk of explosion. Do not replace the battery with an incorrect type. Dispose

of used batteries according to the instructions.

ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.

Débarrassez-vous des piles usagées selon le mode d’emploi.

Class 1 Laser Product

Any service to this product must be carried out by Extron Electronics and its qualified

service personnel.

CAUTION: Using controls, making adjustments, or performing procedures in a manner

other than what is specified herein may result in hazardous radiation exposure.

NOTE: For more information on safety guidelines, regulatory compliances,

EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and

Regulatory Compliance Guide” on the Extron website.

Complies with 21 CFR 1040.10 and 1040.11.

Produit laser de classe1

Si ce produit a besoin d’un quelconque entretient, celui-ci doit être fait par

ExtronElectronics et son personnel qualifié.

ATTENTION : L’utilisation de commandes, la réalisation de réglages, ou l’exécution de

procédures de manière contraire aux dispositions établies dans le présent document,

présente un risque d’exposition dangereuse aux radiations.

Remarque : Pour plus d'informations sur les directives de sécurité, les conformités de

régulation, la compatibilité EMI/EMF, l'accessibilité, et les sujets en lien, consultez le

«Informations de sécurité et de conformité Extron» sur le site internet d'Extron.

Conforme aux sections 1040.10 et 1040.11 du titre 21 du Code des règlements

fédéraux des États-Unis.

Conventions Used in this Guide

Notifications

The following notifications are used:

WARNING: Potential risk of severe injury or death.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X1# *X1** X2^* X2(* X2& CE}

NOTE: For commands and examples of computer or device responses mentioned

in this guide, the character “0” is used for the number zero and “O” represents the

capital letter “o.”

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specification are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.

Contents

Introduction ................................................1

About this Guide .................................................. 1

About the FOX3 Matrix Switchers ........................ 1

Fiber Optic I/O Boards ..................................... 3

Audio I/O Board ............................................... 3

Controller Board .............................................. 3

Fiber Cable Transmission Modes ..................... 4

Features .............................................................. 4

Installation .................................................. 7

Setup and Installation Checklist ........................... 7

Get Ready ....................................................... 7

Configure the Matrix Switcher .......................... 7

Perform Physical Installation ............................ 7

Rear Panel Boards, Cabling, and Features ........... 8

I/O Boards ....................................................... 9

Cooling Fan Assembly ................................... 10

Ethernet Connection ...................................... 10

Remote Port .................................................. 11

Reset Button and LED ................................... 11

Power Supply Modules .................................. 12

Audio Connections ........................................ 12

Operation..................................................13

Front Panel Features .......................................... 13

Power ................................................................ 14

Matrix Operations .............................................. 14

Secure Direct Port Access ................................. 14

Reset Operations ............................................... 15

Performing Soft System Resets

(Resets 3, 4, and 5) ...................................... 17

Performing a Hard Reset (Reset 1) ................. 17

Troubleshooting ................................................. 17

SIS Conﬁguration

and Control ............................................... 18

Connections Options ......................................... 18

Rear Panel RS-232 Port ................................ 18

Front Panel Configuration Port ....................... 18

Ethernet (LAN) Port ........................................ 19

Establishing a Connection.............................. 19

Using Verbose Mode ..................................... 20

Host-to-Switcher Instructions ............................ 20

Switcher-initiated Messages .......................... 20

Switcher Error Responses ............................. 21

Using the Command and Response Tables ....... 22

System Deﬁnitions ............................................. 23

Command and Response Table for

SIS Commands ................................................ 24

Product Conﬁguration Software .................29

Product Conﬁguration Software ......................... 29

Software Operation via Ethernet .................... 29

Software/Firmware Installation ........................... 30

Connecting to PCS ............................................ 32

Device Discovery Panel .................................. 32

TCP/IP Panel ................................................. 33

Offline Device Preview .................................... 34

Software Overview ............................................. 35

Software Menu .............................................. 35

Internal Web Pages ...................................40

Accessing the Internal Web Page ...................... 40

Disabling Compatibility Mode ......................... 41

Web Page Panels .............................................. 41

Device Info Panel ........................................... 42

Device Status Panel ....................................... 43

FOX3 Matrix Series Switchers • Contents vii

Network Settings Panel ................................. 43

Firmware Panel .............................................. 44

Roles and Permissions Panel ......................... 45

Dante Device Info Panel ................................. 46

About the FOX3Matrix .................................. 46

Maintenance and Modiﬁcations .................47

Mounting the Switcher ....................................... 47

UL Guidelines ................................................ 47

Mounting Instructions .................................... 48

Battery and Power Precautions ......................... 48

FOX3 Matrix Replacement Cards ....................... 48

Removing and Installing an I/O Module .............. 49

Removing and Installing a

Power Supply Module ...................................... 51

Removing and Installing a Fan Assembly ........... 52

FOX3 Matrix Series Switchers • Contents viii

Introduction

WARNING: The FOX3 matrix switcher outputs continuous invisible light (Class 1

rated), which may be harmful to the eyes; use with caution.

• Do not look into the rear panel fiber optic cable connectors or into the fiber optic

cables themselves.

• Plug the attached dust cap into the optical transceiver when the fiber optic cable is

unplugged.

AVERTISSEMENT : Le FOX3 émet une lumière invisible en continu (conforme à la

classe1) qui peut être dangereuse pour les yeux , à utiliser avec précaution.

• Ne regardez pas dans les connecteurs de câble ﬁbre optique sur le panneau arrière

ou dans les câbles ﬁbre optique eux-mêmes.

• Branchez la protection contre la poussière dans l’ensemble émetteur/récepteur

lorsque le câble ﬁbre optique est débranché.

• About this Guide

• About the FOX3 Matrix Switchers

• Features

About this Guide

This guide contains installation, configuration, and operating information for the Extron

FOX3 Matrix Switchers. These customizable matrix switchers support Extron fiber optic

endpoints (transmitters and receivers) up to:

• FOX3 Matrix 24x — 24 inputs and outputs.

• FOX3 Matrix 40x — 40 inputs and outputs.

• FOX3 Matrix 80x — 80 inputs and outputs.

• FOX3 Matrix 160x — 160 inputs and outputs.

• FOX3 Matrix 320x — 320 inputs and outputs.

About the FOX3 Matrix Switchers

The FOX3 Matrix Switcher (see figure1 on page2) distributes optical input signals

to one or more optical outputs. The matrix switcher can route multiple input/output

configurations simultaneously. The switcher is configurable, assembled from individual

input/output (I/O) boards, each of which supports 8 inputs and 8 outputs.

The FOX3 Matrix Switchers are compatible with the FOX3 endpoints.

FOX3 Matrix Series Switchers • Introduction 1

FOX3 MATRIX CONTROL

FOX3 MATRIX AUDIO

DANTE EXPANSION

FAN ASSEMBLY

Tx G

1-4041-80

Rx

INPUTS / OUTPUTS

AUDIO OUTPUTS

L

1

R

L

3

R

L

2

R

L

4

R

AUDIO INPUTS

L

1

R

L

3

R

L

2

R

L

4

R

RESET

RS-232

DMP

EXPANSION

AT

LINK

AUDIO EXPANSION

DISCONNECT POWER

CORD BEFORE

SERVICING

PRIMARY

50-60 Hz

100-240V --A MAX

DISCONNECT POWER

CORD BEFORE

SERVICING

REDUNDANT

50-60 Hz

100-240V --A MAX

FOX3 MATRIX 80X

LANREMOTE

FOX3 MATRIX 8io

IN

5

OUTIN

1

OUT IN

6

OUT

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

FOX3 MATRIX 8io

5

OUTIN

1

OUT IN

6

OUTIN

2

OUT IN

7

OUTIN

3

OUT IN

8

OUTIN

4

OUT IN

R

100-240V 0.7A MAX

50-60 Hz

FOX3 R 301

HDMI

LAN

OUT

A

IN OUT IN

B

INPUTS

CONTROL

AUDIO

RETURN

REMOTE

OUTPUTS

3D

SYNC

L

AUDIO

R

L

R

Tx

RS-232

IR

Rx Tx RxG

Tx Rx G S 5V

100mA

1

2 1

500mA

USB 2.0

USB HID

DEVICES

R

100-240V 0.7A MAX

50-60 Hz

FOX3 R 301

HDMI

LAN

OUT

A

IN OUT IN

B

INPUTS

CONTROL

AUDIO

RETURN

REMOTE

OUTPUTS

3D

SYNC

L

AUDIO

R

L

R

Tx

RS-232

IR

Rx Tx RxG

Tx Rx G S 5V

100mA

1

2 1

500mA

USB 2.0

USB HID

DEVICES

R

100-240V 0.7A MAX

50-60 Hz

FOX3 T 301

HDMI

USB HID

HOST HOST

USB 2.0

LAN

OUT

A

IN OUT IN

B

LOOP OUT

OUTPUTS

CONTROL

AUDIO

RETURN

REMOTE

INPUTS

3D

SYNC

L

AUDIO

R

L

R

Tx

RS-232

IR

Rx Tx RxG

Tx Rx G S 5V

R

100-240V 0.7A MAX

50-60 Hz

FOX3 T 301

HDMI

USB HID

HOST HOST

USB 2.0

LAN

OUT

A

IN OUT IN

B

LOOP OUT

OUTPUTS

CONTROL

AUDIO

RETURN

REMOTE

INPUTS

3D

SYNC

L

AUDIO

R

L

R

Tx

RS-232

IR

Rx Tx RxG

Tx Rx G S 5V

R

100-240V 0.7A MAX

50-60 Hz

FOX3 T 301

HDMI

USB HID

HOST HOST

USB 2.0

LAN

OUT

A

IN OUT IN

B

LOOP OUT

OUTPUTS

CONTROL

AUDIO

RETURN

REMOTE

INPUTS

3D

SYNC

L

AUDIO

R

L

R

Tx

RS-232

IR

Rx Tx RxG

Tx Rx G S 5V

R

100-240V 0.7A MAX

50-60 Hz

FOX3 T 301

HDMI

USB HID

HOST HOST

USB 2.0

LAN

OUT

A

IN OUT IN

B

LOOP OUT

OUTPUTS

CONTROL

AUDIO

RETURN

REMOTE

INPUTS

3D

SYNC

L

AUDIO

R

L

R

Tx

RS-232

IR

Rx Tx RxG

Tx Rx G S 5V

1.2A MAX

100-240V ~ 50-60Hz

PWR OUT = 12W

+V +S -S G

1

4

2 3 7

5 6 8

S G S G S G S GTx Rx G Tx Rx G Tx Rx G Tx Rx G

RTSCTS

1 2

1 2 3 41 2 3 4

321 4 G

Tx Rx G Tx Rx G Tx Rx G Tx Rx G

RTS

CTS

S G S G S G S G

5 6 7 8 5 6 7 8

SWITCHED 12 VDC

40W MAX TOTAL

3 4

COM

eBUS

FLEX I/ORELAYSIR/SERIAL

12 VDC

AV

LAN

MODEL 80

FLAT PANEL

MODEL 80

FLAT PANEL

TLP Pro 725M

7" Wall Mount Touchlink

Pro Touchpanel

FOX3 T 301

Fiber Optic Transmitter

for HDMI

4K Display

USB Headset

Keyboard

Mouse

Ethernet

4K HDMI

USB

FOX3 T 301

Fiber Optic Transmitter

for HDMI

4K HDMI

USB

FOX3 T 301

Fiber Optic Transmitter

for HDMI

4K HDMI

USB

FOX3 T 301

Fiber Optic Transmitter

for HDMI

Computer

4K HDMI

USB

RS-232

4K HDMI

Fiber

USB

Ethernet

FOX3 R 301

Fiber Optic Receiver

for HDMI

4K Display

USB Headset

Keyboard

Mouse

RS-232

4K HDMI

USB

FOX3 R 301

Fiber Optic Receiver

for HDMI

IPCP Pro 555

IP Link Pro Control

Processor

FOX3 Matrix 80x

Modular Fiber Optic

Matrix Switcher

AV Control

Network

Figure 1. Typical FOX3 Matrix 80x Application

The matrix switchers are a single box solution to complex fiber optic and broadcast signal

routing applications. Each input and output is individually isolated and buffered. Any input

can be switched to any one output or all outputs with virtually no crosstalk or signal noise

between channels.

The matrix switchers are housed in rack-mountable, high metal enclosures with mounting

flanges for a standard 19-inch rack. The switchers have two IEC power input connectors to

provide 100 VAC to 240 VAC, 50-60Hz power to the unit.

1

FOX3 Matrix Series Switchers • Introduction 2

Fiber Optic I/O Boards

By adding or removing I/O boards, the size of the FOX3 matrix switcher can be increased

and decreased within the range of an 8-input by 8-output matrix to:

• FOX3 Matrix 24x — 24 inputs and outputs.

• FOX3 Matrix 40x — 40 inputs and outputs.

• FOX3 Matrix 80x — 80 inputs and outputs.

• FOX3 Matrix 160x — 160 inputs and outputs.

• FOX3 Matrix 320x — 320 inputs and outputs.

NOTE: The I/O boards are hot-swappable. You do not need to power down the

switcher to remove or install an I/O board.

The Extron proprietary fiber optic signal can include video, stereo audio, and transmitter-

to-receiver RS-232 serial communications. The FOX3 transmitters include all of the same

content plus USB extension.

Audio I/O Board

The matrix switchers have a removable audio board that includes four analog audio inputs

and four analog audio outputs, a DMP expansion port, and two Dante audio network ports.

NOTES:

• The FOX3 Matrix 24x has two analog audio inputs and two analog audio outputs.

• The audio board is hot-swappable. You do not need to power down the switcher to

remove or install an audio board.

Controller Board

The controller board has the reset button and two rear panel remote control connectors, the

LAN (Ethernet) RJ-45 port and Remote RS-232 port.

The matrix switcher can be remotely controlled using either the Extron Product Configuration

Software or the Simple Instruction Set (SIS). Control is available via:

• A rear panel Remote RS-232 port

• A rear panel LAN port

• A front panel USB Config (configuration) port

SIS is a set of basic ASCII code commands that provide simple control through a control

system or PC without the need to enter long strings of code. SIS commands can be entered

via any of the ports listed above.

The switcher can be operated remotely by any of the following connected to the switcher:

• A control system

• A PC computer

NOTE: The controller board is hot-swappable. You do not need to power down the

switcher to remove or install a controller board.

FOX3 Matrix Series Switchers • Introduction 3

Fiber Cable Transmission Modes

The FOX3Matrix Switchers are assembled from individual input/output (I/O) boards. The

switcher can include multiple I/O boards, depending on the matrix model. Each I/O board

supports up to 8 inputs and 8 outputs. The two types of I/O boards are:

• Singlemode — Very long distance, up to 20 km (12.43 miles)

• Multimode — Long distance, up to 500 m (1640 feet)

Increase or decrease the size of the FOX3Matrix Switchers from an 8-input by 8-output

matrix by adding or removing I/O boards to up to a 320-input by 320-output matrix for the

FOX3Matrix320x.

NOTE: Multimode and singlemode fiber optic I/O boards can be mixed in a FOX3 matrix

switcher, but be sure to connect the proper transmission mode fiber cables to each

board.

Features

• I/O sizes:

• FOX3 Matrix 24x: 8x8 to 24x24 • FOX3 Matrix 160x: 8x8 to 160x160

• FOX3 Matrix 40x: 8x8 to 40x40 • FOX3 Matrix 320x: 8x8 to 320x320

• FOX3 Matrix 80x: 8x8 to 80x80

• Switches 4K/60 video, audio, USB, control, and 3D sync over fiber optic cable

• Compatible with all Extron FOX3 Series transmitters and receivers — Supports

FOX3 extenders for an enterprise-wide fiber optic distribution system.

• Supports mathematically lossless 4K video up to 4096x2160 at 60 Hz with 4:4:4

chroma sampling over one fiber

• Supports uncompressed 4K video up to 4096x2160 at 60 Hz with 4:4:4 chroma

sampling over two fibers — Provides the highest quality video distribution system.

• Audio embedding — Any selected two-channel PCM audio signal can be embedded

into any selected output signal, including the analog return audio signal.

• Audio de-embedding — Any two-channel PCM audio signal from a transmitter or

analog return audio from a receiver can be extracted and independently routed.

• Analog audio insertion — Four local stereo audio inputs can be routed to any audio

output, including audio to any connected FOX3 receiver, analog return audio to a FOX3

transmitter, the DMP expansion port, any analog output port, or a Dante audio network.

• Analog audio extraction — Four local stereo audio outputs provide audio from any

audio input, including any connected FOX3 transmitter, DMP expansion port, analog

audio input port, or Dante audio network.

• Digital audio expansion port provides a connection to an Extron DMP 128 Plus

processor for audio system scalability — The DMP expansion port allows the

FOX3Matrix and any non-AT DMP model to be linked together via a single shielded

CAT 6 cable. This creates a 16-channel bi-directional 24-bit/48 kHz high-resolution

digital audio expansion bus between the two units, allowing expanded input and output

signal management and routing capabilities.

• Dante

®

audio network interface, DMP expansion port, and analog audio inputs

and outputs — The FOX3 Matrix features unique audio capabilities with leading-edge

audio matrix switching between any input and any output in the FOX3 systems.

FOX3 Matrix Series Switchers • Introduction 4

• Audio breakaway — Offers the capability to separate an embedded audio signal from

its corresponding video signal within the matrix switcher, allowing two-channel PCM

audio and the video signal from one source to be routed to different destinations.

• 64x64 Dante I/O audio networking with Dante Domain Manager and AES67

support — Two Dante ports provide scalability supporting up to 32 stereo inputs and

32 stereo outputs. An audio input received from a Dante network can be routed to

any audio output, including analog audio return channel. An audio output delivered

to the Dante network can originate from any 2-channel audio input. Dante Domain

Manager offers security and logical segmenting on the network. AES67 support ensures

compatibility with a wide variety of network audio devices using standard protocols.

• Compatible with Dante Controller software — Configuration software for setting up

and managing Dante-enabled audio products on an audio network.

• Secure partitioning segregates sources and destinations in a secure

environment — Secure partitioning enables the FOX3 Matrix to be partitioned into

smaller sub-switchers for segregating sources and destinations. Sources can only be

routed to destinations within the same partition.

• Priority switching prevents unauthorized access to sensitive data in a secure

environment — Each input and output is assigned a security level. An output can only

be tied to an input at the same security level or lower, preventing unauthorized access

to sensitive data in a secure environment.

• Modular, field-upgradeable and hot-swappable design — The FOX3 Matrix

provides substantial flexibility, expandability, and affordability by allowing users to select

the configuration required for their systems. Additional input and output boards may be

added at any time for easy and quick upgradeability, expansion, or new technologies.

Hot-swappable components allow the user to replace an I/O board or power supply

at any time without the need to power down the switcher. This is especially useful for

mission-critical applications that require continuous operation.

• RS-232 insertion from the Ethernet control port — System level device control

to all remote locations via the matrix switcher Ethernet port, providing comprehensive

control of endpoints and attached devices without needing additional cabling.

• Multimode and Singlemode I/O boards available — The FOX3 Matrix is

configurable with a mix of multimode and singlemode versions of the FOX3 Matrix I/O

boards, so that both short and long haul transmission can be supported.

• Dual redundant and hot-swappable power supplies — One primary and one

back-up power supply provide added reliability for critical applications.

• Advanced computer-aided diagnostics — Provide 24-hour self-diagnostics of

input/output boards, primary and redundant power supply voltages, fiber links, and

overall functional status of the matrix. Using the Ethernet or RS-232 communications

port, status monitoring is possible for off-site or unmanned locations, such as

government, military, medical, or any other sensitive, 24/7 environments.

• Two AC power inputs — For added power reliability, some 24-hour environments

require two separate AC power sources, one as the primary source and the second for

redundancy. The FOX3 Matrix provides two AC power inputs for continuous connection

to both power sources.

• Industry standard LC connectors provide reliable physical connectivity and

precise fiber core alignment

• Ethernet monitoring and control — The matrix switcher can be proactively

monitored and managed over a LAN, WAN, or the Internet, using standard TCP/IP

protocols. Ethernet control provides for remote selection of input and output ties,

system set-up and configuration, and advanced system diagnostics.

FOX3 Matrix Series Switchers • Introduction 5

• Secure Ethernet communication using SSH - Secure Shell protocol — SSH

protocol ensures communication between the control system and the matrix is

encrypted.

• RS-232 control port — Enables the use of serial commands for integration into

a control system. Extron products use the SIS - Simple Instruction Set command

protocol, a set of basic ASCII commands that allow for quick and easy programming.

• Front panel USB configuration Port — Enables easy system configuration without

having to access the rear panel.

• JITC Certified — Successfully completed interoperability and information assurance

testing for use in government applications and other mission-critical environments.

• Easy setup and commissioning with Extron PCS - Product Configuration

Software — Conveniently configure multiple products using a single software

application.

• Rack-mountable up to 12U, full rack width metal enclosure

• Internal Extron Everlast power supply — Provides worldwide power compatibility,

with high-demonstrated reliability and low power consumption for reduced operating

cost.

• Extron Everlast Power Supply is covered by a 7-year parts and labor warranty.

FOX3 Matrix Series Switchers • Introduction 6

Installation

This section details the installation and configuration of the FOX3 matrix switchers, including:

• Setup and Installation Checklist

• Rear Panel Boards, Cabling, and Features

Setup and Installation Checklist

Get Ready

 Familiarize yourself with the FOX3 matrix switcher.

 Obtain IP setting information for the matrix switcher from the local network administrator

(see Network Settings Panel on page43).

Configure the Matrix Switcher

 Install the desired I/O boards (see Removing and Installing an I/O Module on

page49).

 Install the Product Conﬁguration Software (PCS) (see Software/Firmware Installation

on page30).

 (Optional) Upload a System Map (see the FOX3 Matrix Series PCS Help File).

Perform Physical Installation

 If desired, install the switcher in a rack (see Mounting the Switcher on page47 ).

 Cable input and output devices to the I/O boards (see Rear Panel Boards, Cabling,

and Features on page8).

 If desired, connect computers or control systems to any of the remote control ports on

the switcher

• Rear panel Remote RS-232 serial port (see Remote Port on page11).

• Rear panel LAN port (see Ethernet Connection on page10).

• Front panel USB Configuration port (see Front Panel Configuration Port on

page18).

 Connect power (see Power on page14).

 Test the switcher by creating a tie (see Output switching on page24).

FOX3 Matrix Series Switchers • Installation 7

Rear Panel Boards, Cabling, and Features

ATTENTION:

• Use electrostatic discharge (ESD) precautions (be electrically grounded) when you

make connections. ESD is damaging, even if you cannot feel, see, or hear it.

• Prenez des précautions contre les décharges électrostatiques (ESD) (soyez

électriquement relié à la terre) lorsque vous effectuez des connexions. Les ESD

peuvent endommager l’équipement, même si vous ne pouvez pas le sentir, le voir

ou l’entendre.

WARNING: The FOX3 matrix switchers outputs continuous invisible light (Class 1

rated), which may be harmful to the eyes; use with caution. Plug the attached dust

cap into the optical transceiver when the fiber optic cable is unplugged.

AVERTISSEMENT : Le FOX3 émet une lumière invisible en continu (conforme à la

classe 1) qui peut être dangereux pour les yeux, à utiliser avec précaution. Branchez

la protection contre la poussière dans l’ensemble émetteur/récepteur lorsque le câble

ﬁbre optique est débranché.

NOTE: Below is the rear panel for the FOX3 Matrix 80x. The other Matrix frames have

the same types of connections with a difference in the number of inputs and outputs.

PRIMARY

FOX3 MATRIX 80x

L R

AUDIO EXPANSION

AT

DMP

EXPANSION

LINK

AUDIO OUTPUTS

L R

AUDIO INPUTSS

4

3

2

1

4

3

2

1

FOX3 MATRIX

CONTROL FL

FAN ASSEMBLY

Extron

INPUTS / OUTPUTS

LINK

FOX3 MATRIX AUDIO

DANTE EXPANSION

50/60Hz

100-240V ~ x.xA MAX.

100-240V

~ x.xA MAX.

DISCONNECT POWER

CORD BEFORE

SERVING

DISCONNECT POWER

CORD BEFORE

SERVING

REDUNDANT

1 - 40

41 - 80

RESET

Tx Rx G

RS-232

LAN

REMOTE

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

GGGGGGG HHHHHHH IIIIIII

JJJ K K K

BBBBBBB

FFFFFFF

AAAAAAA

CCC

CCCC

DDD

DDDD

EEE

EEEE

FFF

FFFF

Figure 2. FOX3 Matrix 80x Fiber Optic Matrix Switcher Rear Panel

A

Fiber optic boards with connectors and LEDs

G

Power connectors

B

Replaceable fan assembly

H

Audio Inputs

C

LAN Ethernet port

I

Audio Outputs

D

Remote RS-232 port

J

DMP Expansion port and LED

E

Reset button and LED

K

Dante AT Expansion ports

F

Power supplies

2

FOX3 Matrix Series Switchers • Installation 8

I/O Boards

As shown in figure2 on page8, each I/O board slot is identified by the input and

output numbers supported by the board position, which are printed on the side of each fan

module.

NOTES:

• Ensure the proper fiber cable for your I/O board. Typically, singlemode

fiber has a

yellow jacket and multimode cable has an orange or aqua jacket.

• Each I/O board has 8 SFPs with an IN and OUT, numbered from left to right.

• Unlike most Extron transmitters and receivers, which output an optical stream

on one connector in a block and receive a return optical stream on the second

connector in the same block, the FOX3 matrix switchers use one connector on

the block as an input and the second connector on the same block as a separate

output.

• All transceiver modules on a fiber optic I/O board, as delivered from Extron, are

configured the same: either all multimode or all singlemode.

• Multimode and singlemode fiber optic I/O boards in a FOX3 matrix switcher can be

used, but be sure to connect the proper transmission mode fiber cables to each

board.

A

Fiber optic boards with connectors and LEDs —

(see figure2)

1

Input connector — Connect a fiber optic cable between

each Input LC connector and a FOX3 transmitter or any other

compatible Extron FOX device.

NOTE: For USB, return audio, and serial RS-232 (receiver-

to-transmitter) function, connect the far end to the optical

Out connector on a FOX receiver.

Input LED — See Fiber optic I/O board LED indications on

page10.

2

Output connector — Connect a fiber optic cable between

each output LC connector and a FOX3 receiver or any other

compatible Extron FOX device.

NOTE: For USB, return audio, and serial RS-232 (receiver-

to-transmitter) function, connect the far end to the optical

In connector on a FOX transmitter.

Output LED — See Fiber optic I/O board LED indications

on page10.

OUT IN

*

Optional for

return data

OUTPUTS

Transmitting

Unit

Receiving

Unit

FO

X3 Matrix

Switcher

A

IN*

*

Optional for

return data

1

OUT

INPUTS

A

IN

OUT*

2

211

FOX3 Matrix Series Switchers • Installation 9

Fiber optic I/O board LED indications

On the fiber optic I/O boards, the input and

output LEDs on the transceivers light green

when 10G light is detected. The arrow

LEDs point to the input and output port they

represent (see figure3).

In figure3, SFP 1 and SFP 5 are examples of

the LEDs that indicate the input and output

port (different colors are used to indicate the

connection only).

OUT

IN

4

OUT

IN

8

OUT

IN

3

OUT

IN

7

OUT

IN

2

OUT

IN

6

OUT

IN

1

OUT

IN

5

FOX3 MATRIX 8io

Figure 3. Fiber Optic I/O Board LEDs

• Out 1 is red and the corresponding arrow LED is red.

• In 1 is blue and the corresponding arrow LED is blue.

• Out 5 is purple and the corresponding arrow LED is purple.

• In 5 is green and the corresponding arrow LED is green.

Cooling Fan Assembly

B

Replaceable fan assembly (see figure2 on page8) — This removable fan

assembly has multiple fans (see Removing and Installing a Fan Assembly on

page52 to replace the fan assembly).

Ethernet Connection

C

LAN Ethernet port — For IP control of the system, connect the matrix switcher

to a PC or an Ethernet LAN via this RJ-45 connector. Use a PC to control the

networked switcher with SIS Configuration and Control on page18 or Product

Configuration Software on page29 from anywhere in the world.

• Link LED indicator — The green (link) LED indicates that the switcher is properly

connected to an Ethernet LAN. This LED should light steadily.

• Act LED indicator — The yellow (activity) LED indicates transmission of

data packets on the RJ-45 connector. This LED should flicker as the switcher

communicates.

NOTE: The factory default settings are: IP address = 192.168.254.254,

Subnet mask = 255.255.255.0, Gateway = 0.0.0.0, and DHCP = Off

Cabling

It is vital that the Ethernet cables be the correct cable type and be properly terminated with

the correct pinout. Ethernet links use Category (CAT) 3, 5e, or CAT 6, unshielded twisted

pair (UTP) or shielded twisted pair (STP) cables, terminated with RJ-45 connectors. Ethernet

cables are limited to a length of 328 feet (100 meters).

NOTES:

• Do not use standard telephone cables. Telephone cables do not support Ethernet.

• Do not stretch or bend cables. Transmission errors can occur.

The cable used depends on your network speed. The unit supports:

• 10 Mbps (10Base-T — Ethernet) — Requires CAT 3 UTP or STP cable at minimum.

• 100 Mbps (100Base-T — Fast Ethernet) — Requires CAT 5e UTP or STP cable at

minimum.

• 1000Mbps(1000Base-T — IEEE 802.3ab) half-duplex and full-duplex

Ethernet— Requires CAT 5, CAT 5e, CAT 6, or CAT 7 UTP or STP cable.

3

FOX3 Matrix Series Switchers • Installation 10

RJ-45 connector wiring

The Ethernet cable can be terminated as a straight-through cable or a crossover cable and

must be properly terminated for your application (see figure4).

• Crossover cable — Direct connection between the computer and the

FOX3 matrix switcher.

• Patch (straight) cable — Connection of the FOX3 Matrix Switcher to an Ethernet LAN.

A cable that is wired as T568A at one end

and T568B at the other (Tx and Rx pairs

reversed) is a "crossover" cable.

A cable that is wired the same at both ends is

called a "straight-through" cable, because

no pin/pair assignments are swapped.

12345678

RJ-45

Connector

Inser

t Twisted

Pair Wires

Pins:

Crossover Cable Straight-through Cable

1

2

3

4

5

6

7

8

Wire color

White-green

Green

White-orange

Blue

White-blue

Orange

White-brown

Brown

Wire color

T568A T568B

End 1 End 2 End 1 End 2

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

1

2

3

4

5

6

7

8

Wire color

White-orange

White-green

Blue

White-blue

White-brown

Brown

Wire color

T568BT568B

White-orange

OrangeOrange

White-green

Blue

White-blue

GreenGreen

White-brown

Brown

Figure 4. RJ-45 Connector and Pinout Tables

Remote Port

D

Remote RS-232 port — Connect a host device, such as a computer or touchpanel

control, to the switcher via this 3-pole captive screw port for serial RS-232 control (see

figure5 for wiring).

RS-232

Tx Rx G

REMOTE

TransmitReceive

ReceiveTransmit

GroundGround

DB9 Pin Locations

Female

51

96

Pin 2 = Rx

Pin 3 = Tx

Pin 5 = G

Computer

Figure 5. Remote RS-232 Wiring

See SIS Configuration and Control on page18 for definitions of the SIS

commands (serial commands to control the switcher via this connector) and Product

Configuration Software on page29 for details on how to install and use the control

software.

Reset Button and LED

E

Reset button and LED — Initiate four levels of matrix switcher reset. For different

reset levels, press and hold the recessed button while the switcher is running or while

powering up the switcher (see Reset Operations on page15 for details).

NOTE: The factory configured passwords for all accounts on this device have

been set to the device serial number. In the event of a complete system reset, the

passwords convert to the default, which is extron for the Admin and User.

4

5

FOX3 Matrix Series Switchers • Installation 11

Power Supply Modules

F

Power supplies (see figure2 on page8) — The Primary and Redundant power

supplies are hot-swappable (see Removing and Installing a Power Supply Module

on page51 to replace power supplies).

There are two corresponding LEDs on the front panel that indicate the status of each

power supply (see Front Panel Features on page13).

G

Power connectors — Plug standard IEC power cords into these connectors to

connect the switcher to 100 VAC to 240 VAC, 50 or 60 Hz power sources.

NOTE: For the most reliable power, connect the power cord from the Redundant

power connector to either an uninterruptible power source or a power source

completely independent from the primary power source.

Audio Connections

H

Audio Inputs — Connect audio input devices to an audio 5-pole captive screw port

(see figure6 to wire the captive screw connector).

Unbalanced Stereo Input

Balanced Stereo Input

Do not tin the wires!

Tip

Ring

Tip

Ring

LR

Sleeves

Tip

Sleeve

Tip

LR

Figure 6. Audio Input Wiring

I

Audio Outputs — Connect audio output devices to an audio 5-pole captive screw port

(see figure7 to wire the captive screw connector).

Unbalanced Stereo Output Balanced Stereo Output

Do not tin the wires!

Tip

No Ground Here

Tip

LR

Sleeves

Tip

Ring

Tip

Ring

LR

Sleeves

Figure 7. Audio Output Wiring

ATTENTION:

• For unbalanced audio, connect the sleeves to the ground contact. DO NOT

connect the sleeves to the negative (-) contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS

connecter les manchons aux contacts négatifs (–).

J

DMP Expansion port and LED — (see figure2 on page8)

• Expansion Port — Connect an STP cable between this port and the Expansion

port on an optional Extron DMP Digital Matrix Processor for digital audio

connection. Receive and transmit eight 2-channel stereo inputs and eight 2-channel

stereo outputs via this RJ-45 connection.

NOTE: Only connect non-AT audio devices to the DMP Expansion port.

• Link LED — Lights to indicate that the port is connected to a compatible device.

K

Dante AT Expansion ports — Connect RJ-45 connectors to external Dante devices

for digital audio networking. Receive and transmit 32 2-channel inputs and 32

2-channel outputs via these two RJ-45 connections.

The FOX3 Matrix uses Dante Controller for Windows from Audinate to select and route

inputs and outputs for all connected Extron FOX3 transmitters and receivers and other

Dante-compatible audio devices.

Download and install the latest version of Dante Controller for Windows from the Dante

Controller product page (see Software/Firmware Installation on page30).

6

7

FOX3 Matrix Series Switchers • Installation 12

La page charge ...

Extron FOX3 Matrix 80x Manuel utilisateur

Ce manuel convient également à

Extron FOX3 Matrix 80x Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents