Extron FOX3 SR 301 Manuel utilisateur

User Guide

FOX3 SR 301

FOX3 SR 311

Fiber Optic Extenders

Fiber Optic HDMI Scaling Receivers

68-3130-01 Rev. A

05 23

Safety Instructions



Copyright

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (®), registered service marks (SM), and trademarks (TM) are the property of RGBSystems, Inc. or Extron (see the

current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks (®)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, GlobalConfigurator,

GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NAV,

NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,

SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTPSystems, and ZipClip

Registered Service Mark(SM) : S3 Service Support Solutions

Trademarks (™)

AAP, AFL (Accu-RATEFrameLock), ADSP(Advanced Digital Sync Processing), AVEdge, CableCover, CDRS(ClassD Ripple Suppression),

Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator,

DSVP(Digital Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital,

Opti-Torque, PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope-Trigger, SIS, SimpleInstructionSet,

Skew-Free, SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause interference. This interference must be corrected at the expense of the user.

Battery Notice

This product contains a battery. Do not open the unit to replace the battery. If the

battery needs replacing, return the entire unit to Extron (for the correct address, see the

Extron Warranty section on the last page of this guide).

CAUTION: Risk of explosion. Do not replace the battery with an incorrect type.

Dispose of used batteries according to the instructions.

ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de

pile. Débarrassez-vous des piles usagées selon le mode d’emploi.

Class 1 Laser Product

Any service to this product must be carried out by Extron and its qualified service personnel.

CAUTION: Using controls, making adjustments, or performing procedures in a manner

other than what is specified herein may result in hazardous radiation exposure.

NOTE: For more information on safety guidelines, regulatory compliances,

EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and

Regulatory Compliance Guide on the Extron website.

Complies with 21 CFR 1040.10 and 1040.11.

Produit laser de classe1

Si ce produit a besoin d’un quelconque entretient, celui-ci doit être fait par Extronet son

personnel qualifié.

ATTENTION : L’utilisation de commandes, la réalisation de réglages, ou l’exécution

de procédures de manière contraire aux dispositions établies dans le présent

document, présente un risque d’exposition dangereuse aux radiations.

Remarque : Pour plus d'informations sur les directives de sécurité, les conformités de

régulation, la compatibilité EMI/EMF, l'accessibilité, et les sujets en lien, consultez le

«Informations de sécurité et de conformité Extron» sur le site internet d'Extron.

Conforme aux section 1040.10 et 1040.11 du titre 21 du Code des règlements

fédéraux des États-Unis.

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

WARNING: Potential risk of severe injury or death.

AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,0p1 scene 1,1 ^B 51 ^W^C.0

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X! *X1&* X2)* X2#* X2! CE}

NOTE: For commands and examples of computer or device responses used in this

guide, the character “0” is the number zero and “O” is the capital letter “o.”

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.

viiFOX3SR 301 and FOX3SR311 Scaling Receivers • Contents

Contents

Introduction ................................................1

About this Guide .................................................. 1

Product Description ............................................. 1

Fiber Cable Transmission Modes ..................... 2

Extron LinkLicense........................................... 3

Features .............................................................. 3

Installation .................................................. 5

Installation Overview ............................................ 5

Rear Panel Features ............................................ 5

Connector and Cable Details ............................... 8

HDMI Connectors ............................................ 8

Analog Audio Connectors ................................ 9

RS-232 and IR Connectors............................ 10

TP Cable Termination and

Recommendations ....................................... 10

USB HID and USB 2.0 Connectors ................ 11

Operation.................................................. 12

Front Panel Features .......................................... 12

Operations......................................................... 13

Using the On-Screen Menu System ................... 13

Menu Selection Buttons ................................. 13

Menu Overview .............................................. 14

Using the Menu Screens ................................ 14

Quick Setup Submenu................................... 15

Front Panel Lockout (Executive Mode) ............... 17

Source Information OSD .................................... 17

Reset Modes ..................................................... 17

Conﬁguration ..................................................... 18

EDID .............................................................. 18

HDCP Output ................................................ 19

Audio Conﬁguration ........................................... 19

Audio De-embedding..................................... 19

Audio Output Volume ..................................... 19

Audio Mute .................................................... 19

Audio Return ................................................. 19

RS-232 Insertion ............................................... 20

SIS Conﬁguration and Control ...................21

Host Control Ports ............................................. 21

Rear Panel RS-232 Port ................................ 21

Front Panel Conﬁguration USB Port ............... 21

Ethernet (LAN) Ports ...................................... 22

Establishing a Connection.............................. 22

Simple Instruction Set Control ........................... 23

Host-to-Unit Instructions ................................ 23

Device-Initiated Power-Up Message .............. 23

Error Responses ............................................ 23

Timeout ......................................................... 23

Using the Command and Response Table ..... 24

Common symbol deﬁnitions........................... 25

Command and Response Table for

SIS Commands ................................................ 27

Conﬁguration Software .............................32

Software/Firmware Installation ........................... 32

Connecting to PCS ............................................ 34

Device Discovery Panel .................................. 34

TCP/IP Panel ................................................. 35

Ofﬂine Device Preview .................................... 35

Software Overview ............................................. 36

Software Menu .............................................. 37

Device Menu.................................................. 39

Internal Web Page ..................................... 41

Accessing the Internal Web Page ...................... 41

Web Page Panels .............................................. 42

Details Panel .................................................. 42

Status Panel .................................................. 42

Date and Time Panel ..................................... 43

Network Panel ............................................... 44

Passwords Panel ........................................... 45

LinkLicense Panel .......................................... 45

Firmware Panel .............................................. 46

About the FOX3SR301/311 ......................... 47

FCC Class A Notice .............................................iv

Battery Notice .....................................................iv

Class 1 Laser Product .........................................iv

Produit laser de classe1......................................iv

Notiﬁcations ...................................................... v

Software Commands ........................................v

Speciﬁcations Availability ......................................v

Extron Glossary of Terms ......................................v

FOX3SR 301 and FOX3SR311 Scaling Receivers • Contents viii

Equipment Mounting ................................. 48

Mounting the Scaling Receiver........................... 48

Tabletop Use ................................................. 48

Mounting kits ................................................. 48

UL Rack-Mounting Guidelines ....................... 49

FOX3SR 301 and FOX3SR311 Scaling Receivers • Introduction 1

Introduction

WARNING: The FOX3SR301 and FOX3SR311 output continuous invisible light

(Class 1 rated), which may be harmful to the eyes; use with caution.

AVERTISSEMENT : Le FOX3SR301 et FOX3SR311 émet une lumière invisible en

continu (conforme à la classe1) qui peut être dangereux pour les yeux, à utiliser avec

précaution.

• Do not look into the rear panel fiber optic cable connectors or into the fiber optic

cables themselves.

• Ne regardez pas dans les connecteurs de câble fibre optique sur le panneau arrière

ou dans les câbles fibre optique eux-mêmes.

• Plug the attached dust cap into the optical transceiver when the fiber optic cable is

unplugged.

• Branchez la protection contre la poussière dans l’ensemble émetteur/récepteur

lorsque le câble ﬁbre optique est débranché.

About this Guide

This guide contains information about the Extron FOX3SR301 and FOX3SR311 fiber

optic scaling receivers.

Product Description

The FOX3SR301 and FOX3SR311 Scaling Receivers are ultra-high performance fiber

optic receivers to accept proprietary optical signals from long haul transmission of the

following over two fiber optic cables (see figure1 on page2):

• Uncompressed or visually lossless HDCP-compliant 4096x2160 or 3840x2160 (UHD)

@60Hz HDMI video with Deep Color

• 2-CH LPCM audio

• RS-232 and IR control signals

• USB HID (for Human Interface Devices such as keyboards and mice)

• USB 2.0 (FOX3SR301 only)

• 3D Sync

The scaling receivers extend HDMI signals up to:

• 20 km (12.4 miles) for the singlemode cables

• 500 m (1640 feet) with 50 µm OM4 4700 MHz bandwidth laser optimized multimode

cables (see Fiber Cable Transmission Modes on page2).

The receiver has two HID USB ports (both models) to connect one or two peripheral devices

and a USB 2.0 port (FOX3SR301) that connects directly to USB devices. It can receive

RS-232, IR, and USB returns from controlled devices and send them to the transmitter via a

proprietary optical signal.

FOX3SR 301 and FOX3SR311 Scaling Receivers • Introduction 2

The receivers have many controls, including audio adjustments, that are available under

Remote RS-232 and USB port Simple Instruction Set (SIS) control and PCS. Both units

have video, audio, fiber light status, and lost-light alarm indicators.

NOTE: The FOX3 receiver is compatible with all Extron FOX3 transmitters. The FOX3

products are not compatible with legacy FOX, FOXBOX, FOX II, PowerCage 401 FOX,

or PowerCage 1600 FOX products.

Fiber Cable Transmission Modes

The receivers are further categorized by the type of fiber optic cable, multimode or

singlemode, which define the effective range of transmission:

Multimode — Long distance, up to 500 m (1640 feet) (depending on the fiber cable)

Singlemode — Very long distance, up to 20 km (12.4 miles)

NOTE: The multimode and singlemode units are physically and functionally identical,

with the exception of the effective range of transmission. In this guide, any reference

applies to either transmission mode unless otherwise specified.

60-60 Hz

100-240V

~

0.7A MAX

L R

LR

RS-232

Tx Rx Tx Rx

G

IR

A

OUT

R

IN

OUTPUTS

AUDIO

RETURN

INPUTS

CONTROL

B

OUT IN

USB 2.0

AUDIO OUT

FOX3 SR 301

LAN

1

2

HDMI

DEVICES

USB HID

100 mA

REMOTE

RS-232

Tx Rx S5VG

3D

SYNC

STANDBY

CLASS 2 WIRING

12

XPA 1002

LEVEL

1

1212

LIMITER/

PROTECT

SIGNAL

2

INPUTS OUTPUT

REMOTE

00

VOL/MUTE

10V50 mA

100-240V 1.3A, 50-60Hz

60-60 Hz

100-240V

~

0.7A MAX

LR

RS-232

Tx Rx Tx RxG

IR

A

OUT

R

IN

INPUTS

AUDIO

RETURN

OUTPUTS

CONTROL

B

OUT IN

HDMI

LOOP OUT

USB 2.0

AUDIO

FOX3 T 301

LAN

HOST HOST

REMOTE

RS-232

Tx Rx S 5VG

3D

SYNC

USB HID

Ethernet

HDMI

Loop out

HDMI

Output

HDMI Input

Extron

SI 28

Surface-mount

Speakers

Extron

XPA 1002

Power Amplier

4K Display

4K Media Player

Local

Monitor

4K

Up to 20 km (12.43 miles)

Singlemode Fiber

SM Model

Audio

Output

RS-232

Extron

FOX3 T 301

Fiber Optic Transmitter

Extron

FOX3 SR 301

Fiber Optic Receiver

LAN

MODEL 80

POWER

SD CARD USB

PLAY STATUS

Figure 1. Typical FOX3SR301 Scaling Receiver Application

1

FOX3SR 301 and FOX3SR311 Scaling Receivers • Introduction 3

Extron LinkLicense

An Extron LinkLicense unlocks features that add convenience, expand system options, and

enhance the capabilities of Extron products. Each LinkLicense can be purchased separately

from the FOX3 device and activated as the need arises. A LinkLicense can be uploaded

using Extron Toolbelt software and the Toolbelt Help File (see Software/Firmware

Installation on page32 to download Toolbelt).

NOTE: A user must have an Insider Account to download and use ToolBelt Software.

Contact an Extron support representative, to obtain an Insider Account.

LinkLicense upgrades available for the FOX3 receiver include the following:

• Uncompressed Video Upgrade —

• This LinkLicense is enabled once and lasts for the life of the product.

• Allows the FOX3 devices to pass uncompressed 4K @ 60 Hz video on the second

SFP module, enabling the highest video performance.

Features

• Receives fiber optic signals from FOX3 Series transmitters and provides

scaled HDMI video, USB, stereo audio, RS-232 control, IR control, and 3D sync

signals.

• High-performance scaler provides selectable output resolutions up to

4096x2160 at 60 Hz with 4:4:4 chroma sampling.

• Supports mathematically lossless 4K video up to 4096x2160 at 60 Hz with 4:4:4

chroma sampling over one fiber.

• Supports uncompressed 4K video up to 4096x2160 at 60 Hz with 4:4:4 chroma

sampling over two fibers.

• Supported HDMI 2.0 specification features include data rates up to 18 Gbps,

Deep Color up to 12 bit, and 3D.

• HDCP 2.3 compliant.

• Supports USB 2.0 to 1.0 devices and USB 3.0 devices that can operate at USB

2.0 data rates of up to 480 Mbps (FOX3 SR 301 only) — Provides USB extension,

allowing connection to peripheral devices over the same fiber optic cable as video and

audio.

• Device class filtering on USB HID port restricts the range of device types

to HID — Device class filtering prevents unauthorized downloading or uploading of

content via the USB HID port in secure environments. The USB HID port is configured

at the factory, such that device class filtering cannot be removed or altered in the field.

• HDMI audio de-embedding with analog stereo outputs — Digital HDMI audio is

made available as a balanced or unbalanced analog stereo signal on captive screw

connectors.

• Key Minder continuously verifies HDCP compliance for quick, reliable

switching — Authenticates and maintains continuous HDCP encryption between

input and output devices to ensure quick and reliable switching in professional AV

environments.

• Analog audio return channel — Provides balanced return analog stereo audio input

to support a remote audio source at the receiver.

• HDCP Visual Confirmation — When HDCP encrypted content is transmitted to a non

HDCP compliant display, a full screen green signal is sent to the display for immediate

visual confirmation that protected content cannot be viewed on that display.

FOX3SR 301 and FOX3SR311 Scaling Receivers • Introduction 4

• Bidirectional RS-232 and IR signal transmission over fiber optic cabling for AV

device control — Bidirectional RS-232 and IR control pass-through enables a remote

display to be controlled without the need for additional cabling. Two fibers are required

for bidirectional communications.

• HDMI video upscaling and downscaling — Features the built-in Extron-exclusive

Vector 4K scaling engine for optimized upscaling and downscaling of high-resolution

video signals.

• On-screen display — Features an on-screen display that provides status data

pertaining to the currently selected input, facilitating easy adjustment of picture settings.

• Aspect ratio control — The aspect ratio of the video output can be controlled by

selecting a FILL mode, which provides a full screen output, or a FOLLOW mode, which

preserves the original aspect ratio of the input signal.

• Internal test patterns for calibration and setup — Test patterns include grayscale,

crosshatch, crop pattern, color bars, and alternating pixels.

• Integrated two-port HID hub with 100mA available on each port — Allows

simultaneous connection to multiple peripheral devices, including keyboards, mice, and

other HID—Human Interactive Devices.

• Host emulation on the USB HID ports — Offers increased system reliability by

emulating a continuous connection between the HID-compliant keyboard and mouse

and a host.

• LinkLicense Support — Extron LinkLicense unlocks features that add convenience,

expand system functionality, and enhance the capabilities of Extron products.

• Front panel USB configuration port — Enables easy system configuration without

having to access the rear panel.

• Ethernet monitoring and control — Enables control and proactive monitoring over a

LAN, WAN, or the Internet.

• RS-232 control — Features an RS-232 serial port for control and configuration.

• Real-time status LED indicators for troubleshooting and monitoring — Front

and rear panel LEDs verify signal presence, HDCP authentication, fiber link status, and

power.

• Easy setup and commissioning with Extron PCS - Product Configuration

Software — Conveniently configures multiple products using a single software

application.

• Compatible with Extron FOX3 Series matrix switchers — Creates

HDCP-compliant signal distribution systems.

• JITC Certified — Successfully completed interoperability and information assurance

testing for use in government applications and other mission-critical environments.

• Industry standard LC connectors provide reliable physical connectivity and

precise fiber core alignment.

• Available as an 850 nm multimode model for moderate-range transmissions up

to 500 m (1640 feet) and a 1310 nm singlemode model for extreme distances up

to 20 km (12.4 miles).

• 1U high, half rack width metal enclosure.

• Internal Extron Everlast power supply — Provides worldwide power compatibility,

with high demonstrated reliability and low power consumption for reduced operating

cost.

• Extron Everlast Power Supply is covered by a 7-year parts and labor warranty.

FOX3SR 301 and FOX3SR311 Scaling Receivers • Installation 5

Installation

This section details the installation of the FOX3SR 301 and FOX3SR311 scaling receivers,

including:

• Installation Overview

• Rear Panel Features

• Connector and Cable Details

Installation Overview

Follow these steps to install and set up an Extron FOX3SR 301 and FOX3SR311 receivers

for operation:

1. Turn off all of the equipment. Ensure that the video source and the output display are all

turned off and disconnected from the power source.

2. Mount the receiver (see Mounting the Scaling Receiver on page48).

3. Connect the cables and configure the units.

4. Plug in the power supplies, then turn on the display and the input.

Rear Panel Features

50-60 Hz

100-240V ~0.7A MAX

LR

RS-232

Tx Rx Tx RxG

IR

A

OUT

R

IN

OUTPUTS

AUDIO

RETURN

INPUTS

CONTROL

B

OUTIN

AUDIO

FOX3 SR 311

LAN

1

2

HDMI

DEVICES

USB HID

100 mA

REMOTE

RS-232

Tx Rx S5VG

3D

SYNC

50-60 Hz

100-240V ~0.7A MAX

LR

RS-232

Tx Rx Tx RxG

IR

A

OUT

R

IN

OUTPUTS

AUDIO

RETURN

INPUTS

CONTROL

B

OUTIN

USB 2.0

AUDIO

FOX3 SR 301

LAN

1

2

HDMI

DEVICES

USB HID

100 mA 500 mA

REMOTE

RS-232

Tx Rx S5VG

3D

SYNC

1

J

K

KI

I

IG

G

GC

C

CB

B

BA

A

AH

H

D

DJ

J

F

E

Figure 2. FOX3Scaling receivers Rear Panel Connectors

A Power inlet E USB Device ports I LAN Ethernet port

B Power LED F HDMI output J SFP module and LEDs

C Audio Return G Remote RS-232/3D Sync port K Reset button

D Audio output H Control RS-232/IR port

A Power inlet — Plug a standard IEC power cord into this connector to connect the unit

to a 100 VAC to 240 VAC, 50-60 Hz power source.

2

FOX3SR 301 and FOX3SR311 Scaling Receivers • Installation 6

B Power LED (see figure2 on page5) — The lit LED indicates power is applied.

C Audio Return— Connect a balanced or unbalanced audio input to this 5-pole captive

screw port for return to the transmitter (see Analog Audio Connectors on page9

to wire this connector).

D Audio output — This 5-pole captive screw port outputs the transmitted, unamplified,

line level analog audio (see Analog Audio Connectors to wire this connector).

NOTE: If embedded digital audio is present on the HDMI output, this analog audio

connector outputs audio unless embedded audio is in multi-ch format.

E USB Device ports — (see USB HID and USB 2.0 Connectors on page11)

• USB HID — Connect USB type A to B cables between this USB type B port

and the USB port of a device. The USB HID ports are used only for a mouse or

keyboard.

• USB 2.0 (FOX3SR301 only) — Connect USB type A to B cables between this

USB type B port and the USB port of a device. The USB 2.0 ports are used for

thumb drives, cameras, keyboards, a mouse, CAC reader, and such devices.

F HDMI output — Connect a video display to this HDMI output port with a maximum

resolution of 4096x2160 @ 60 Hz, 8-bit, 4:4:4 chroma sampling (see HDMI

Connectors on page8 to use the included Extron Lock-It Lacing Bracket).

G Remote RS-232/3D Sync port —

• Remote RS-232 port — For serial control of the receiver, connect a host device,

such as a computer or touch panel control, via the three left poles (Tx, Rx, and G)

of this 5-pole captive screw port (see RS-232 and IR Connectors on page10

to wire this connector).

• 3D Sync port — For stereoscopic 3D sync, such as external IR emitter for glasses,

connect a PC to the two right poles of the REMOTE RS-232/3D Sync 5-pole

captive screw port on the receiver (see RS-232 and IR Connectors to wire this

connector).

H Control RS-232/IR port — Connect a serial RS-232 signal, a modulated or

unmodulated IR signal, or both to this 3.5 mm, 5-pole captive screw port for

bidirectional RS-232 and IR communication (see RS-232 and IR Connectors to wire

the connector).

NOTE: If only one fiber optic cable is connected (see figure3 on page7),

RS-232 or IR reports from the controlled device cannot be received. To receive

responses from the controlled device, two fiber optic cables must be connected.

I LAN Ethernet port — If desired, connect the receiver to an Ethernet LAN or WAN

via this RJ-45 port. Ethernet control allows the operator to control the receiver via SIS

commands, the PCS configuration software, or embedded webpage from a remote

location (see TP Cable Termination and Recommendations on page10 to wire

the connector).

• Link (green) LED — Indicates that the unit is properly connected to an Ethernet

LAN. This LED should light steadily.

• Act (yellow) LED — Indicates transmission of data packets on the RJ-45

connector. This LED should blink as the unit communicates.

FOX3SR 301 and FOX3SR311 Scaling Receivers • Installation 7

J SFP module and LEDs — (see figure2 on page5)

WARNING: The devices output continuous invisible light (Class 1 rated), which

may be harmful to the eyes; use with caution. Plug the attached dust cap into the

optical transceiver when the fiber optic cable is unplugged.

AVERTISSEMENT : Le produit émet une lumière invisible en continu (conforme

à la classe1) qui peut être dangereux pour les yeux, à utiliser avec précaution

Branchez la protection contre la poussière dans l’ensemble émetteur/récepteur

lorsque le câble ﬁbre optique est débranché.

NOTES:

• Ensure the proper ﬁber cables for the transmitter and receiver pair are used.

Typically, singlemode ﬁber has a yellow jacket and multimode cable has an

orange or aqua jacket.

• See ﬁgure3 for ﬁber cable connections. Connect the transmitter to a receiver in

one of three ways:

• One way (transmitter to receiver) only, connect transmitter Outputs A (1) to

receiver Inputs A (1).

• Two way (transmitter to receiver and return), connect transmitter Outputs

A (1) to receiver Inputs A (1) and connect transmitter Outputs A (2) to

receiver Inputs A (2).

• Output B is available to transmit a 4K @ 60 Hz uncompressed signal when

the FOX3 4K @ 60 Hz Uncompressed Video LinkLicense is purchased.

1 Port A Out (required) — For all one-way video, audio,

and serial communications from the transmitter to the

receiver, connect a fiber optic cable to the Out LC port.

Connect the opposite end of this fiber optic cable to

the Port A In LC port on the receiver or to any other

compatible Extron FOX3 device.

2 Port A In (optional) — For one-way return audio, USB,

and serial communications from the receiver to the

transmitter, connect a fiber optic cable to the In LC port.

Connect the opposite end of this fiber optic cable to

the Port A Out LC port on a receiver or to any other

compatible Extron FOX3 device.

• Transmit Optical OUT LED lights solid green when

powered and lights off when there is no power on the

endpoint.

• Receive Optical IN LED lights solid green when light is

present and lights off when there is no power or light

present.

Receiver

T

ransmitter

11

1111

22

2222

22

2222

11

1111

A

OUTIN

OUTPUTS

B

OUTIN

A

OUTIN

INPUTS

B

OUTIN

Figure 3. Fiber

Cable

Connection

K Reset button — Initiates three levels of resets. Use a pointed stylus, ballpoint pen, or

small screwdriver to access the recessed button (see Reset Modes on page17 for

detailed reset information).

3

FOX3SR 301 and FOX3SR311 Scaling Receivers • Installation 8

Connector and Cable Details

HDMI Connectors

HDMI signals run at a very high frequency and are especially prone to errors caused by bad

video connections, too many adapters, or excessive cable length. To avoid the loss of an

image or jitter, follow these guidelines:

• Limit or avoid the use of adapters.

• Use only cables specifically intended for HDMI or DVI signals.

Use the LockIt lacing bracket to securely fasten an HDMI cable to a device:

1. Plug the HDMI cable into the panel connection (see figure4, 1).

3

33

11

44

55

22

Figure 4. Installing the LockIt Lacing Bracket

2. Loosen the HDMI connection mounting screw from the panel enough to allow the

LockIt lacing bracket to be placed over it (2). The screw does not have to be removed.

3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then

tighten the screw to secure the bracket (3).

ATTENTION:

• Do not overtighten the HDMI connector mounting screw. The shield to which it

fastens is very thin and can easily be stripped.

• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel

elle est attachée est très fin et peut facilement être dénudé.

4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing

bracket (4).

5. While holding the connector securely against the lacing bracket, use pliers or similar

tools to tighten the tie wrap, then remove any excess length (5).

4

FOX3SR 301 and FOX3SR311 Scaling Receivers • Installation 9

Analog Audio Connectors

See figure5 to wire connectors for the appropriate input and output type for the analog

audio and audio return audio. Connectors are included with the receiver, but you must

supply the audio cable. Use the supplied tie-wraps to strap the cable to the extended tail of

the connectors.

Unbalanced Stereo Output Balanced Stereo Output

Unbalanced Stereo Input Balanced Stereo Input

Do not tin the wires!

Tip

No Ground Here

Tip

LR

Sleeves

Tip

Ring

Tip

Ring

LR

Sleeves

Tip

Ring

Tip

Ring

LR

Sleeves

Tip

Sleeve

Tip

LR

Figure 5. Captive Screw Connector Wiring for Audio Inputs and Outputs

ATTENTION:

• For unbalanced audio output, connect the sleeves to the ground contact. DO NOT

connect the sleeves to the negative (-) contacts.

• Pour l’audio asymétrique, connectez les manchons au contact au sol. NE PAS

connecter les manchons aux contacts négatifs (–).

• The length of the exposed wires in the stripping process is important. The ideal

length is 3/16 inches (5 mm). Any longer and the exposed wires may touch,

causing a short circuit between them. Any shorter and the wires can be easily

pulled out even if tightly fastened by the captive screws.

• La longueur des câbles exposés est importante lorsque l’on entreprend de les

dénuder. La longueur idéale est de 5 mm (3/16 inches). S’ils sont trop longs, les

câbles exposés pourraient se toucher et provoquer un courtcircuit. S’ils sont trop

courts, ils peuvent être tirés facilement, même s’ils sont correctement serrés par les

borniers à vis.

• Do not tin the wire leads before installing into the connector. Tinned wires are not

as secure in the connector and could be pulled out. They may also break after

being bent several times.

• Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles

étamés ne sont pas aussi bien ﬁxés dans le connecteur et pourraient être tirés. Ils

peuvent aussi se casser après avoir été pliés plusieurs fois.

5

FOX3SR 301 and FOX3SR311 Scaling Receivers • Installation 10

RS-232 and IR Connectors

Figure 6 shows how to wire the Control (RS-232 and IR) connector.

TxRx

RxTx

Gnd

IR Device

RS-232 Device

RxTx RxTxG

RS-232 IR

CONTROL

Figure 6. Control and Sync Connectors Wiring

NOTES:

• The IR Tx and Rx line pair and the RS-232 Tx and Rx line pair must each cross

once between this connector and the source or destination.

• The length and preparation of exposed wires is important (see the audio connector

ATTENTION: on page9 for details).

TP Cable Termination and Recommendations

It is vital that your Ethernet cable be the correct cable type and that it be properly terminated

with the correct pinout. Ethernet links use Category (CAT) 3, 5e, or CAT 6, unshielded

twisted pair (UTP) or shielded twisted pair (STP) cables, terminated with RJ-45 connectors.

Ethernet cables are limited to a length of 328 feet (100 meters).

NOTES:

• Do not use standard telephone cables. Telephone cables do not support Ethernet

or Fast Ethernet.

• Do not stretch or bend cables. Transmission errors can occur.

The cable used depends on your network speed. The unit supports:

10 Mbps (10Base-T — Ethernet), 100 Mbps (100Base-T — Fast Ethernet), and

1000Mbps(1000Base-T — IEEE 802.3ab) half-duplex and full-duplex Ethernet

connections.

• 10Base-T Ethernet requires CAT 3 UTP or STP cable at minimum.

• 100Base-T Fast Ethernet requires CAT 5e UTP or STP cable at minimum.

• 1000Base-T Gigabit Ethernet requires CAT 5, CAT 5e, CAT 6, or CAT 7 UTP or STP

cable.

The Ethernet cable must be terminated as a patch (straight-through) cable and must be

properly terminated in accordance with the TIA/EIA T568-B wiring standard (see figure7).

5

1

2

3

6

7

8

4

Side

12345678

Insert

Twisted

Pair Wires

Pins:

RJ-45

Connector

Wire color

White-green

Green

White-orange

White-blue

Orange

White-brown

Brown

Blue

TIA/EIA T

568 B

Figure 7. RJ-45 Connector and Pinout Tables

6

7

FOX3SR 301 and FOX3SR311 Scaling Receivers • Installation 11

USB HID and USB 2.0 Connectors

NOTES:

• The FOX3 matrix switches the USB HID and USB 2.0 inputs and outputs

independently of the video and each USB connection.

• The USB 2.0 port is only available on the FOX3SR301 devices.

• The USB HID ports are used only for a mouse or keyboard.

• The USB 2.0 ports are used for thumb drives, cameras, keyboards, a mouse, CAC

reader, and such devices.

Transmitter Receiver

50-60 Hz

100-240V ~0.7A MAX

LR

RS-232

Tx Rx Tx RxG

IR

A

OUT

R

IN

OUTPUTS

AUDIO

RETURN

INPUTS

CONTROL

B

OUTIN

USB 2.0

AUDIO

FOX3 SR 301

LAN

1

2

HDMI

DEVICES

USB HID

100 mA 500 mA

REMOTE

RS-232

Tx Rx S5VG

3D

SYNC

50-60 Hz

100-240V ~0.7A MAX

LR

RS-232

Tx Rx Tx RxG

IR

A

OUT

R

IN

INPUTS

AUDIO

RETURN

OUTPUTS

CONTROL

B

OUTIN

HDMI

LOOP OUT

USB HID USB 2.0

AUDIO

FOX3 T 301

LAN

HOST HOST

REMOTE

RS-232

Tx Rx S5VG

3D

SYNC

SM or MM cable

USB

Laptop

Lt

Keyboard

y

Mouse

Thumb Drive

A

AABB

B

Figure 8. Peripheral USB Connections Diagram

A USB Host ports — Connect USB type A to B cable between these USB type B ports

and the USB ports of a host.

Two separate USB cables are required: 1 for USB HID and another 1 for USB 2.0

connections.

B USB Device ports — Connect a USB type A cable between the USB type A port and

peripherals.

Types of USB ports

• USB HID — Connect USB type A to B cables between this USB type B port and the

USB port of a host. The USB HID ports are used only for a mouse or keyboard.

• USB 2.0 (FOX3SR301 only) — Connect USB type A to B cables between this USB

type B port and the USB port of a host. The USB 2.0 ports are used for thumb drives,

cameras, keyboards, a mouse, CAC reader, and such devices.

8

FOX3SR 301 and FOX3SR311 Scaling Receivers • Operation 12

Operation

This section details the operation of the FOX3SR301 and FOX3SR311 receivers,

including:

• Front Panel Features

• Operations

• Using the On-Screen Menu System

• Front Panel Lockout (Executive Mode)

• Source Information OSD

• Reset Modes

• Configuration

• Audio Configuration

• RS-232 Insertion

Front Panel Features

FOX3 SR 301

CONFIG

INPUTS

SIGNAL

HDCP

USB HID

USB 2.0

USB

1 2

MENU

ENTER

HOST

F

FOX3 SR 311

CONFIG

INPUTS

SIGNAL

HDCP

USB HID

USB

1 2

MENU

ENTER

HOST

F

B

BA

A

AC

C

CD

D

DE

E

EF

F

Figure 9. FOX3Scaling receivers Front Panel Features

A Power LED — Lights when the unit is receiving power and is operational.

B Configuration port — This USB mini-B port is used to configure the unit and to

update firmware.

C INPUTS LEDs

• SIGNAL LED — Lights when the unit detects an input video signal.

• HDCP LED — Lights when the input signal is HDCP encrypted.

D USB LEDs —

• USB HID Host LED — When the transmitter and receiver are connected through

the SFP port and a host device is connected to the transmitter, the LED remains lit

to indicate an active connected device.

• USB HID 1 and 2 LEDs —When an active USB peripheral device is connected to

the Devic ports on the receiver, the LED remains lit to indicate an active connected

device.

9

La page charge ...

Extron FOX3 SR 301 Manuel utilisateur

Ce manuel convient également à

Extron FOX3 SR 301 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents