Eccotemp 45HI-NGV Manuel utilisateur

WARNING: If the information in these

instructions is not followed exactly, a re or

explosion may result causing property

damage, personal injury or death.

• Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electrical switch; do

not use any phone in your building.

- Immediately call your gas supplier

from a neighbor’s phone. Follow the gas

supplier’s instructions.

- If you cannot reach your gas supplier,

call the re department.

• Installation and service must be performed

by a qualied installer, service agency or

the gas supplier.

1

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

Use & Care Manual

With Installation Instructions for the Installer

Residential Outdoor Gas 140,00 BTU Max Input @ 6.8 GPM

Tankless Water Heater

WARNING: This water heater may not be suitable

for use in manufactured (mobile) homes! Please check

local code restrictions pertaining to permanent/xed installations in

manufactured homes in your area.

The purpose of this manual is twofold: one, to provide the installer

with the basic directions and recommendations for the proper

installation and adjustment of the water heater; and two, to

the owner-operator, to explain the features, operation, safety

precautions, maintenance and troubleshooting of the water heater.

This manual also includes a parts list.

It is imperative that all persons who are expected to install,

operate or adjust this water heater read the instructions carefully

so they may understand how to perform these operations. If you

don’t understand these instructions or any terms within it, seek

professional advice.

Any questions regarding the operation, maintenance, service or

warranty of this water heater should be directed to the seller from

whom it was purchased. If additional information is required, refer to

the section on If You Need Service.

Do not destroy this manual. Please read carefully and keep in a safe

place for future reference.

Recognize this symbol as an indication of Important Safety Information!

California Proposition 65 Warning: This product contains chemicals known to the

State of California to cause cancer, birth defects or other reproductive harm.

WARNING: If the information in these instructions is not followed exactly, a re or

explosion may result causing property damage, personal injury or death.

FOR YOUR SAFETY!

Improper installation, adjustment, alteration,

service or maintenance can cause property

damage, personal injury, or death. Refer to

this manual. Installation and service must be

performed by a qualied installer, service

agency or the gas supplier.

DO NOT store or use gasoline or other ammable

vapors or liquids or other combustible materials

in the vicinity of this or any other appliance. To

do so may result in an explosion or re.

WHAT TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier,

call the re department.

• DO NOT return to your home until authorized by

the gas supplier or re department.

2

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

FOR YOUR RECORDS

Write the model and serial numbers here:

#_______________________________

You can nd them on a label on the appliance

and/or packaging.

Staple sales slip or canceled check here.

Proof of the original purchase date is needed to

obtain service under the warranty.

READ THIS MANUAL

Inside you will nd many helpful hints on how

to use and maintain your water heater properly.

A little preventive care on your part can save

you time and money over the life of your water

heater. You’ll nd many answers to common

problems in the Troubleshooting Guide. If you

review the chart of Troubleshooting Tips rst,

you may not need to call for service.

READ THE SAFETY INFORMATION

Your safety and the safety of others are very

important. There are many important safety

messages in this manual and on your appliance.

Always read and obey all safety

messages.

This is the safety alert symbol.

Recognize

this symbol as an indication of

Important Safety Information! This

symbol alerts you

to potential hazards that can kill or hurt

you and others.

All safety messages will follow the safety alert

symbol and either the word “DANGER”,

“WARNING”, “CAUTION” or “NOTICE”.

These words mean:

DANGER - An imminently hazardous situation

that will result in death or serious injury.

WARNING - A potentially hazardous situation

that could result in death or serious injury

and/or damage to property.

CAUTION - A potentially hazardous situation

that may result in minor or moderate injury.

NOTICE: Attention is called to observe

a specied procedure or maintain a

specic condition.

Safety Information

Safety Precautions .............3-6

LP Gas Models .......................5

Installation Instructions

Location ..............................7-9

Water Connections ...........9-10

Gas Supply............................10

Relief Valve...........................11

Leak Testing..........................12

High Altitude ........................12

Venting ................................12

Remote Control ..............13-14

Electrical Connection ...........15

Typical Installation ...............16

Pipe Insulation .....................17

Installation Checklist ...........18

Operating Instructions

Start Instructions ............19-20

Water Temperature ............21

Temperature Memory..........21

Care and Cleaning

Maintenance .......................22

Housekeeping .................22-23

Extended Shut-Down ...........23

Anti-Freezing........................23

Draining ...............................24

Troubleshooting Tips

Before You Call ....................25

Error Code Guide ................26

3

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

IMPORTANT SAFETY INFORMATION READ ALL

INSTRUCTIONS BEFORE USING

Be sure to read and understand the entire Use and Care Manual before attempting to install or

operate this water heater. It may save you time and money. Pay particular attention to the Safety

Instructions. Failure to follow these warnings could result in serious bodily injury or death. Should

you have problems understanding the instructions in this manual, or have any questions, STOP, and

get help from a qualied service technician, or the local gas utility.

DANGER!

PROPERLY INSTALL WATER HEATER

Failure to properly install the water heater outdoors as outlined in the Installation

Instructions in this manual can result in unsafe operation of the water heater. To

avoid the risk of re, explosion, or asphyxiation from carbon monoxide, never

operate this water heater unless it is installed properly and has an adequate

air supply for proper operation. Be sure to inspect the ue terminal for proper

installation at initial start-up; and at least annually thereafter. Refer to the Care

and Cleaning section of this manual for more information regarding ue terminal

inspection.

WARNING!

Gasoline, as well as other ammable materials and liquids (adhesives, solvents,

paint thinners etc.), and the vapors they produce are extremely dangerous. DO

NOT handle, use or store gasoline or other ammable or combustible materials

any where near or in the vicinity of a water heater or any other appliance. Be sure

to read and follow the labels on the water heater, as well as the warnings printed

Vapors from ammable

liquids will explode and catch re

causing death or severe burns.

Do not use or store ammable products

such as gasoline, solvents or adhesives

In the same room or area near the

water heater.

Keep ammable products :

1. Far away from heater

2. In approved containers

3. Tightly closed

4. Out of children ‘s reach

Water heater has a main burner ame.

The main burner ame

1. Can come on at any time and

2. Will ignite ammable vapors.

Vapors:

1. Cannot be seen

2. Are heavier than air

3. Go a long way on the oor

4. Can be carried from other rooms to

the main burner ame by air currents.

Installation:

Do not Install water heater where ammable products will be stored or used

unless the main burner ame Is at least 18” above the oor. This will reduce, but

not eliminate, the risk of vapors being ignited by the main burner ame.

Read and follow water heater warnings and Instructions. If owners manual is

missing, contact the retailer or manufacturer.

4

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING

DANGER!

WATER TEMPERATURE SETTING

Safety and energy conservation are factors to be considered when selecting

the water temperature setting. Water temperatures above 125°F can cause

severe burns or death from scalding. The thermostat is adjusted to its lowest

temperature position when shipped from the factory. Be sure to read and follow

the warnings outlined on the label pictured below.

The chart shown above may be used as a guide

in determining the proper water temperature for

your home

DANGER: Households with small children,

disabled, or elderly persons may require a 120°F.

or lower temperature setting to prevent contact

with”HOT” water.

Maximum water temperature occurs while

burner is on. To nd water temperature being

delivered, turn on a hot water faucet and place a

thermometer in the water stream and read the

thermometer.

The temperature of the water at the outlet of

the water heater can be regulated by setting the

temperature on Remote Control . The remote

control was set at 110°F before it was shipped

from the factory.

The illustration to the bottom left illustrates

the Remote Control and how to adjust the water

temperature.

NOTICE: When this water heater is supplying

general purpose hot water requirements for

use by individuals, a thermostatically controlled

mixing valve for reducing point of use water

temperature is recommended to reduce the risk

of scald injury. Contact a licensed plumber or the

local plumbing

authority for further information.

NOTICE: The factory recommended operating

temperatures are between 90°F and 140°F.

Water Temperature

120°F

125°F

130°F

135°F

140°F

145°F

150°F

155°F

Time To Produce a Serious Burn

More than 5 minutes

1 1/2to 2 minutes

About 30 seconds

About 10 seconds

Less than 5 seconds

Less than 3 seconds

About 1 1/2 seconds

About 1 second

Time/Temperature Relationship in Scalds

Table courtesy of Shriners Burn Institute

Water temperature over 125°F can cause severe burns

instantly or death from scalds. Children, disabled and elderly

are at highest risk of being scalded. See instruction manual

before setting temperature at water heater. Feel water

before bathing or showering. Temperature limiting valves are

5

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

DANGER!

NATURAL GAS AND LIQUEFIED PETROLEUM MODELS

Both LP and natural gas have an odorant added to aid in detecting a gas leak.

Some people may not physically be able to smell or recognize this odorant. If you

are unsure or unfamiliar with the smell of LP or natural gas, ask the gas supplier.

Other conditions, such as “odorant fade”, which causes the odorant to diminish in

intensity, can also hide or camouage a gas leak. Always check with commercial

leak detector or soapy water.

• Gas detectors are recommended in LP and natural gas applications and

their installation should be in accordance with the detector manufacturer’s

recommendations and/or local laws, rules, regulations or customs.

• Water heaters utilizing LP gas are different from natural gas models. A natural

gas water heater will not function safely on LP gas and vice versa.

• No attempt should ever be made to convert the water heater from natural gas

to LP gas. To avoid possible equipment damage, personal injury or re, do not

connect the water heater to a fuel type not in accordance with the unit data

plate; propane for propane units and natural gas for natural gas units. These

units are not certied for any other fuel type.

• LP appliances should not be installed· below grade (for example, in a

basement) if such installation is prohibited by federal, state and/or local laws,

rules, regulations or customs.

• Propane or LP gas must be used with great caution. It is heavier than air and

will collect rst in lower areas making it hard to detect at nose level.

• Before attempting to light the water heater, make sure to look and smell for

gas leaks. Use a soapy solution to check all gas ttings and connections.

Bubbling at a connection indicates a leak that must be corrected. When smelling

to detect a gas leak, be sure to sniff near the oor also.

• It is recommended that more than one method, such as soapy solution, gas

detectors, etc., be used to detect leaks in gas applications.

Notice: If a gas leak is present or suspected:

• DO NOT attempt to nd the cause yourself.

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch.

• DO NOT use any phone in your building.

• Leave the house immediately and make sure your family and pets leave

also.

• Leave the doors open for ventilation and contact the gas supplier, a

qualied service agency or the re department.

• Stay away from the house (or building) until the service call has been

made, the leak is corrected and a qualied agency has determined the

area to be safe.

6

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

IMPORTANT SAFETY INFORMATION READ ALL

INSTRUCTIONS BEFORE USING

FOR INSTALLATIONS I N THE STATE OF CALIFORNIA

California Law requires that residential water heaters must be braced, anchored

or strapped to resist falling or horizontal displacement due to earthquake

motions.For residential water heaters up to 52 gallon capacity, a brochure with

generic earthquake bracing instructions can be obtained from: Ofce of the State

Architect, 400 P Street, Sacramento, CA 95814 or you may call 916-445-8100 or

ask a water heater dealer.

However, applicable local codes shall govern installation. For residential water

heaters of a capacity greater than 52 gallons or tankless style, consult the local

building jurisdiction code for acceptable bracing procedures.

SAFETY PRECAUTIONS

Have the installer show you the location of the gas shut-off valve and how to shut

it off if necessary. Turn off the manual shut-off valve if the water heater has been

subjected to overheating, re, ood, physical damage or if the gas supply fails to

shut off.

• Read this manual entirely before installing or operating the water heater.

• Use this appliance only for its intended purpose as described in this

Use and Care Manual.

• Be sure your appliance is properly installed in accordance with local codes

and the provided installation instructions.

• Part of your water heater unless it is specically recommended in this manual.

All other servicing should be referred to a qualied technician.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY .

SAVE THESE INSTRUCTIONS

WARNING!

For your safety, the information in this manual must be followed to

minimize the risk of re or explosion, electric shock, or to prevent property

damage, personal injury, or loss of life.

This water heater must be installed in accordance with these instructions, local codes, utility company requirements, and/

or in the absence of local codes, use the latest edition of the American National Standard/National Fuel Gas Code. A copy

can be purchased from either the American Gas Association, 400 North Capitol Street Northwest, Washington, DC 20001

as ANSI standard Z223.1 or National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02269 as NFPA 54. In

Canada, the latest edition of the CSA B149.1 Natural Gas and Propane Installation, and the Canadian Electrical Code, CSA

C22.1Part1, in the absence of local codes.

7

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

The water heater must be located so it is not

subject to physical damage, for example, by

moving vehicles, area ooding, etc.

The water heater must be installed vertically

with the water, gas, and power connections

on the underside, pointing toward the ground.

Failure to properly install the water heater

outdoors as outlined in this manual can result

in unsafe operation.

Hot and cold water lines should be insulated

to conserve water and energy.

DO NOT install water heater where subject to

vibrations.

DO NOT install the water heater in

Recreational Vehicles, Mobile Homes, Boats

and other Watercraft.

DO NOT install the water heater near vents

for heating or cooling. A minimum of 4 feet

should be maintained.

If the clearances stated on the Instruction/

Warning Label, located on the front panel

of the heater differ, install the water heater

according to the clearances stated on the label.

Location

This water heater is for OUTDOOR

installation ONLY!

Make sure before installation that the gas

type you will use is the same type on the

data plate.

The water heater unit should be installed by

professionals from your local gas company.

Please don’t attempt installation by yourself.

Improper installation may cause failure or

dangerous conditions such as gas leaking or

explosion.

This water heater is an outdoor model and

must be mounted on a vertical wall. It must

not be installed indoors or in a conned

space. The water heater should be installed

close to the most frequently used outlet and

its position chosen with safety and service in

mind.

Make sure people (particularly children,

disabled, and elderly) will not touch the

hot water outlet or the ue terminal. The

ue terminal and air inlet must be clear of

obstruction and shrubbery.

If installed in a public corridor, please assure

that the surrounding area is free of debris,

obstruction and ammable materials.

The unit must be installed on a re retardant

area, and must be away from all ammable

materials. Clearance should be 1.75 ft to the

left and right side of ammable materials,

and 6.75 ft to the front.

The unit should be installed in open area

where strong currents are not prevalent

This unit is of high power and will consume

a lot of oxygen when working, so the

installation area must be well ventilated, and

air in and out of the area has no blockage.

The outdoor unit should not be installed in a

corridor with rooms on the both sides or in

the closed corridor.

Take measures to avoid direct wind, rain

and snow. The installation area should be

constructed of re retardant materials. The

power socket connecting the water heater

should be properly grounded.

Installing the water heater

WARNING: Combustible construction

refers to adjacent walls and ceilings and

should not be confused with combustible

or ammable products and materials.

Combustible and/or ammable products

and materials should never be stored in

the vicinity of this or any gas appliance.

8

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

Proper operation of the water heater requires air for combustion and ventilation. Provisions for

combustion and ventilation air must comply with referenced codes and standards.

Combustion and Ventilation Air

This water heater is for OUTDOOR installation ONLY.

It must NOT be installed indoors or in a conned space.

Installing the water heater

Corrosive Atmospheres

The air in beauty shops, dry cleaning establishments, photo

processing labs, and storage areas for liquid and powdered

bleaches or swimming pool chemicals often contain such

halogenated hydrocarbons.

An air supply containing halogenated hydrocarbons may be safe

to breathe, but when it passes through a gas ame corrosive

elements are released that will shorten the life of any gas

burning appliance.

Propellants from common spray cans or gas leaks from A/ C and

refrigeration equipment are highly corrosive after passing through

a ame.

The water heater warranty is voided when failure of the heater is

due to operation in a corrosive atmosphere.

NOTICE: The water heater

should not be installed near

an air supply containing

halogenated hydrocarbons.

Inspect Shipment

Inspect the water heater for possible damage. Check the markings on the rating plate of the water

heater to be certain the type of gas supplied corresponds to the water heater requirements. Verify

all included parts are present (see below).

2

9

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

• When the water is supplied from a water

supply tank, the height of the tank and the

diameter of the pipes and their relation to

water pressure, should be taken into

consideration. Gravity water pressure is

not recommended.

NOTICE: If the water ow resistance of a

shower head is too high, the burner in the

water heater will fail to ignite. Keep the

shower head clean from debris that could

cause additional pressure drop.

NOTICE: If using mixing valves on the outlet,

choose one which prevents cold water

pressure from overcoming hot water line

pressure.

IMPORTANT: Do not apply heat to the HOT

or COLD water connections. Any heat applied

to the water supply ttings will permanently

damage the internal components of the water

heater.

Water Supply Connections

Plumbing should be carried out by a qualied

plumber in accordance with local codes.

Use approved plumbing materials and tools only.

To conserve energy and to prevent freezing,

insulate both cold and hot water supply lines.

DO NOT cover the drain valves.

To ensure proper operation of the water

heater, the following water pressure

guidelines should be followed:

• Operation of the water heater requires the

minimum water pressure of 14 psi and a

minimum water ow rate of 0.75 gpm.

• Additional water pressure is required for

long pipe runs and outlet tting(s) water

pressure drops.

• To maintain proper performance, ensure

sufcient water supply pressure. The

Required Water Pressure = Min. Operating

Water Pressure (14 psi) + Pipe Pressure

Loss + Faucet and Shower Pressure Loss +

Safety Margin (more than 5 psi).

• To supply hot water to upper oors,

additional water pressure (0.44 psi/ft)

must be ensured.The measurement should

be calculated by the distance between the

water inlet of the water heater (ground

level) to the hot water faucet (upper oor level).

• Well water systems should be set at a

range of 50-60 psi.

Mounting the Water Heater

Make sure the location of the appliance allows for easy access

and operation.

In case of dry wall or concrete wall use dry wall anchors or lag bolts.

The water heater requires 120VAC/ 60Hz. Have a receptacle with

ground terminal near the water heater. The length of the power

supply cord is 5 feet.

Drill the holes as per the sizes in the gure to the left, put 2

expansion screws into the top holes, and 2 rubber screws into the

bottom holes.

Hang up the water heater unit, tighten the expansion screws, and

put 2 wood thread screws into the bottom holes.

CAUTION: Reinforcement of the wall is

required in case the wall is not strong enough

to hold the appliance.

CAUTION: This water heater must

only be used with the following water

supply system conditions:

• With clean, potable water free of

corrosive chemicals, sand, dirt, or

other contaminates.

• With inlet water temperatures

above 32°F, but not exceeding 120°F.

• Free of lime and scale deposits.

• DO NOT reverse the hot and cold

water connections. The water

heater will not operate.

10

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

Water Supply Connections Continued

If a water heater is installed in a closed water supply system, such as one

having a backow preventer in the cold water supply line, means shall be

provided to control thermal expansion. Contact the water supplier or local

plumbing inspector on how to control this situation. Install a shutoff valve

near the inlet of the water heater for service and draining purposes.

Before connecting the water supply pipe to the water heater, open

the shutoff valve ·and clean out sand, debris, air, caulking material,

etc. inside the pipe. Connect to the water inlet, then check water ow.

Close the shutoff valve and clean the water lter.

Be sure to connect the water inlet and the hot water outlet as shown

on the water heater. If reversed, the water heater will not function.

Installation of unions or exible copper connections are

recommended on the HOT and COLD water lines, so that the water

heater may disconnect easily for servicing if necessary.

Install a Check Valve between the water heater and the water

shutoff

valve. (See illustration to the top left).

In regards to the HOT WATER OUTLET:

Connections between the water heater and point(s) of use should be

as short and direct as possible.

DO NOT use lead or non-approved plastic pipe.

NOTICE: The ow rate of hot water may vary when more than two

faucets (appliances, xtures, etc.) are being used simultaneously.

NOTICE: The pipes MUST be completely drainable. If the hot water faucets are located at a point higher

than the water heater, place a drain valve at the lowest point (see illustration to the bottom left).

Gas Supply

WARNING: Do not attempt to convert this water heater for use with a different type of gas

other than the type shown on the rating plate. Such conversion could result in hazardous operating

conditions. Please have a professional connect the gas pipe.

A Manual Gas Appliance Shutoff

Valve must be installed at the gas

connection of the water heater at the

time of installation (see diagram to

the left). The branch gas supply line to

the water heater should be clean black

steel pipe or other approved gas piping

material.

A ground joint union or ANSI design

certied semi-rigid or exible gas

appliance connector should be

installed in the gas line close to the

water heater. The National Fuel Gas

Code (NFGC) mandates a manual gas

shut-off valve: See (NFGC) for complete

instructions.

If exible connectors are used, the

maximum length shall not exceed 36”.

If lever type gas shut offs are used,

they shall be T-Handle type.

Compound used on the threaded

joints of the gas piping must be of

the type resistant to the action of LP

gas. Use compound sparingly on male

threads only.

A sediment trap should be installed

at the bottom of the gas line.

Do not use excessive force (over

31.5 ft lbs.) in tightening the pipe,

particularly if pipe-tape compound

is used, as the unit may be damaged.

The inlet gas pressure to the water

heater must not exceed 10.5 “ w.c.

for natural or 14” w.c. for LP gas. For

purposes of input adjustment, the

minimum inlet gas pressure (with

main burner on) is shown on the

water heater rating plate. If high or

low gas pressures are present, contact

your gas supplier for correction.

11

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

Relief Valve

• The pressure rating of the relief valve must not exceed

150 psi, the maximum working pressure of the water

heater as marked on the rating plate.

• The BTUH rating of the relief valve must equal or exceed

the BTUH input of the water heater as marked on its

rating plate.

• No valve of any type should be installed between the

relief valve and the water heater.

• Discharge from the relief valve should be piped to a

suitable drain to eliminate potential water damage. Piping

used should be of a type approved for the distribution of

hot water.

• Hot and cold water lines should be insulated up to the

water heater.

• The discharge line must be NO SMALLER than the outlet

of the valve and must pitch downward to allow complete

drainage (by gravity) of the relief valve and discharge line.

• The end of the discharge line should not be threaded or

concealed and should be protected from freezing. No

valve of any type, restriction or reducer coupling should

be installed in discharge line.

NOTICE: Local codes govern the installation of relief valves. If local codes require that a temperature

and pressure relief valve should be installed the manufacturer recommends a type 40XL Watts T&P

relief valve or an equivalent model be used.

NOTICE: Manual operation of relief valves should be performed at least once a year. Turn off the

electrical power and gas shutoff valve. Lift and release lever on the relief valve and check the manual

operation of the relief valve. You should take precaution to avoid contact with the hot water coming

out of the relief valve and to prevent water damage.

NOTICE: If the relief valve on the system discharges periodically, this may be due to thermal expansion

in a closed water supply system. Contact the water supplier or local plumbing inspector on how to

correct theis situation. Do not plug the relief valve.

A new pressure relief valve, complying with the Standard for relief Valves and Automatic Gas Shut-Off Devices

for Hot Water Supply Systems, ANSI Z21.22, must be installed at the hot water outlet connection of the water

heater at the time of installation. Local codes shall govern the installation of relief valves.

For safe operation of the water heater, be sure that:

NOTICE: The above illustrates

a pressure only relief valve.

If local codes require a

combination temperature

and pressure relief valve be

installed, an extension piece

may be needed.

Pressure Testing the Gas Supply System

WARNING: Install a gas pressure regulator, in the gas supply line, which does not exceed the

maximum supply pressure.

DO NOT use an industrial type gas regulator.

Failure to isolate heater during pressure test can damage internal components voiding warranty. The water

heater must be isolated from the gas piping system by closing the manual gas shut-off valve during any pressure

testing of the gas supply piping at pressures equal to or less than 1/2 psi (14’w.c.).

12

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

Leak Testing

WARNING: Never use an open ame to test for gas leaks, as property damage, personal

injury, or death could result.

The water heater and its gas connections must be leak tested at normal operating pressures before

it is placed in operation.

• Turn on the gas shut-off valve(s) to the water heater.

• Use a commercial leak detector or soapy water solution to test for leaks at all connections and ttings.

Bubbles indicate a gas leak that must be corrected.

The factory connections should also be leak tested after the water heater is placed in operation.

High Altitude

Ratings of gas appliances are based on sea level operation and need not be changed for installations at

elevations up to 2,000 feet.

Unit not recommended for elevations in excess of 2,000 feet

Installing the water heater.

Flue Terminal Location

The location of the vent terminal depends on the following minimum clearances and considerations

(see illustration):

• Twelve (12) inches above grade level and above normal snow levels.

• Four (4) feet below, or four (4) feet horizontally from any door,

window, soft, under eave vent or gravity air inlet to the building

or other appliances, or from gas or electric meters. Do not locate

vent above walkways, doors, windows, air inlets, gas or electric

meters or other equipment.

• Ten (10) feet from any forced air inlet to the building. Any fresh or

make-up air inlet such as for a dryer or furnace area

is considered to be a forced air inlet.

• Eighteen (18) inches from an inside corner formed by two exterior walls.

• DO NOT install vent terminal under any patio or deck.

• To help prevent moisture from freezing on walls and under eaves,

do not locate vent terminal on the side of a building

with prevailing winter winds.

• DO NOT locate vent terminal too close to shrubbery, as ue

gases may damage them.

• Caulk all cracks, seams and joints within six (6) feet of vent terminal.

• All painted surfaces should be primed to lessen the chance of

physical damage. Painted surfaces will require maintenance.

Additional Considerations

WARNING : Moisture in the ue gas will condense as it leaves the vent terminal. In cold weather

this condensate can freeze on the exterior wall, under the eaves and on surrounding objects.

Some discoloration to the exterior of the building is to be expected. However, improper location

or installation can result in severe damage to the structure or exterior nish of the building. Code

requirements are subject to change and may vary by location.

13

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

WARNING : Field wiring connections and electrical grounding must comply with local codes, or in

the absence of local codes, with the latest edition of the National Electrical Code, ANSI/NFPA 70, or in

Canada, Canadian Electrical Code, CSA C22.1 Part 1

Remote Control Installation

The following are considerations for determining the location of the remote control(s):

• Avoid areas where the remote control(s)

may be subjected to oil and/or steam from

cooking.

• Avoid areas where chemical agents (such as

thinner, benzine and alkaline) are used.

• Avoid areas of direct sunlight.

• The MAXIMUM distance between the water

heater and the remote control(s) installation

location is limited to 50 feet.

• No other manufacturer’s controls are

suitable for use with this water heater.

• DO NOT attempt to disassemble the

remote control.

• DO NOT install any remote control outdoors.

• Place remote control(s) out of children’s reach.

• The remote control(s) can be installed in

convenient locations such as the kitchen,

laundry room, or utility room.

• The included remote control can be placed in

a convenient location in a bathroom, however,

AVOID areas where water may come into

contact with the control(s).

• Avoid areas where the remote control(s

may be exposed to heat, e.g. stove ranges or

heaters.

Remote control - Connection, Installation and Set

(For Panel Control/Remote Control and Remote Control units)

Panel Control/Remote Control and Remote Control units will work with either one or two

remote controls. If two remotes are desired, a wire connector will need to be provided. To

connect the remote control:

1. For one control: Plug the aviation joint into the socket directly on the water heater

(see illustration below)

2. For two controls: First, cut off the aviation joints on the two controllers, plug one into

the socket on the water heater (length is dependent on your requirements), and throw away

the other. Then connect the wires of the aviation joint to the inlet wire of the connector, and

connect the two remote control to the outlet wires of connector.

14

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

Installation of Remote Control

1. Remove the front cover of the Remote Control. (See illustration below)

2. At installation site, mark and screw two holes with 0.24” with 1.2” depth. Insert 2 rubber screws into

the holes. Place the remote control against the wall, align the holes of control with the holes in the

wall, and fasten them with wood thread screws. (See illustration below)

3. Replace the front cover on the remote control.

15

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

HARDWIRING THE ELE CTRICAL

CONNECTIONS:

• Wiring should be carried out by a qualied

electrician in accordance with local codes.

• The water heater requires 120 VAC/60Hz

and should be properly grounded.

• DO NOT connect grounding wire to water

pipes, gas pipes, telephone cables,

lightning conductor circuits and to

grounding circuit of other equipment that

carry a ground-fault interrupter.

• An ON/OFF switch must be provided and

installed for the incoming 120VAC power.

• Wire the water heater exactly as shown

below. A wiring diagram is also found inside

of the cover panel.

• A green screw is provided in the junction

box for grounding connection.

• Connect the live wire to black leg wire and

the neutral wire to the white neutral wire.

Electrical Connection

POWER CORD:

• The electric power supply requirement for

this water heater is 120 VAC/60HZ, 2 Amps.

• The water heater comes with a three (3) pin

power supply cord. Use only a power outlet

with a ground terminal.

• The installation of an electric leakage

breaker is recommended. (GFCI)

• Keep any excess of the power supply cord

on the outside of the water heater.

• If local codes require hardwiring, see

instructions for “Hardwiring the Electrical

Connections”.

WARNING :Field wiring connections and electri cal grounding must comply with local codes, or in

the absence of local codes, with the la test edition of the National Electrical Code,ANSI/NFPA 70, or in

Canada, Canadi an Electrical Code, CSA C22.1Part1.

WARNING: Shock hazard line voltage is

present. Before servicing the water heater, turn

off the electrical power to the water heater at the

main disconnect or circuit breaker. Failure to do so

could result in severe personal injury or death.

CAUTION: Label all wires prior to

disconnection when servicing controls. Wiring

errors can cause improper and dangerous

operation. Verify correct operation after servicing.

Electric Wiring Diagram

16

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

Installing the water heater.

Typical Installation ( Some Items May Not Apply)

NOTICE: The National Fuel Gas Code (NFGC) mandates a manual gas shut- off valve: See (NFGC)

for complete instructions. Local codes or plumbing authority requirements may vary from the

instructions or diagrams provided and take precedent over these instructions.

17

Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locator: Eccotemp.com/locator

Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483

Insulation blankets, available to the

general public, for external use on

gas water heaters are not

necessary. The purpose of an

insulation blanket is to reduce the

standby heat loss encountered with

storage tank heaters. This water

heater does not store water making

an insulation blanket unnecessary.

The manufacturer’s warranty does

not cover any damage or defect

caused by installation, attachment

or use of any type of energy saving

or other unapproved devices

(other than those authorized by

the manufacturer) into, onto or in

conjunction with the water heater.

The use of unauthorized energy

saving devices may shorten the

life of the water heater and may

endanger life and property.

The manufacturer disclaims any

responsibility for such loss or injury

resulting from the use of such

unauthorized devices.

WARNING: If

local codes require

external application of

insulation blanket kits

the manufacturer’s

instructions included

with the kit must be

carefully followed.

Hot and Cold Pipe

Insulation Installation

For increased energy efciency,

use pipe insulation. Please install

the insulation, according to the

illustrations above, making sure to

insulate all the way to the top. Do not

cover any drain or pressure valve(s).

Pipe Installation

Inlet Pipe and Outlet Pipe Installation

Use pressure resistant pipe to connect the inlet and outlet

water pipes of the water heater and the local water pipe

(Make sure to place the rubber ring).Before connecting the

inlet water pipe, ush the inside of the pipe.

NOTICE: The hot and cold pipes

should be insulated as shown help to

provide additional freeze protection

During Installation of this water heater…

Do’s

• DO check inlet gas pressure to ensure that it is within the range specied on the rating plate.

• DO provide adequate air for combustion and ventilation as discussed in the Use & Care Manual and the

National Gas Code (CAN/CGA B 149 in Canada).

• DO maintain proper clearances to combustibles as specied by applicable code.

• DO ensure that the ue terminal location complies with the guidelines found in the Use & Care Manual and

National Fuel Gas Code (CAN/CGA B 149 in Canada).

Dont’s

• DON’T block or restrict Air Intake Opening located on the back side of the water heater.

• DON’T remove the front cover unless absolutely necessary. This should only be done after being examined by a

qualied service technician.

• DON’T install this product where standing water may occur.

La page charge ...

Eccotemp 45HI-NGV Manuel utilisateur

Eccotemp 45HI-NGV Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents