MAXHUB RC01 Manuel utilisateur

Marque
MAXHUB
Modèle
RC01
Catégorie
Télécommandes
Taper
Manuel utilisateur
User Manual
Product name ：RC01
1、ID
2、Electric Capability
3、Environmental
No.
Item
3.1
Operating Temperature
The RCU shall be capable of operating in an ambient temperature range of 0ºC to +40ºC.
3.2
Operating Humidity
The device shall be capable of operating in a relative humidity range of 8% to 90%, non-condensing.
N0
Item
Test Requirements
2.0
IC IC Mcu
RTL8752CJF
2.1
remote control model
RC01
2.2
Carrier frequency
2402----2480MHZ
2.3
Working Voltage
DC 3v
2.4
Static Current
6uA～500uA
2.5
Working Current
<30mA
2.6
RF distance
Working Voltage(3V)
IR>8m IR 15°>6m RF>10m
2.7
Mouse operating distance
>10m
2.8
Supported Operating Systems
Android4.3 or above
2.9
Code Table
Refer to the Code Table
2.10
Schematic Diagram
Refer to Schematic Diagram
2.11
Battery life
2.12
RF frequency range & modulation
2.13
RF transmission power
2.14
Carrier frequency offset, drift
2.15
Antenna gain
2.16
Agreement
2.17
Actual performance test
3.3
Storage Temperature
The RCU shall be capable of operating after being stored in an ambient temperature range of -40º
to +70ºC.
3.4
Storage Humidity
The RCU shall be capable of operating after being stored in a relative humidity range of 5% to 90%,
non-condensing.
3.5
Test temperature
-10 ºC ~ 50 ºC
4、Key introduction and code value
1) If Bluetooth is not connected or disconnected, infrared is emitted by default.
2) Infrared code format: NEC format.
3) Infrared user code: 0x21DE
4) Bluetooth key transmission protocol: BT4.2BLE
Num.
Func_key
Usage Page
Usage ID
Linux Code
IR CODE
（0x21DE）
1
Power
NA
KEY_POWER
0x01
2
VOL+
0x0C
0xe9
KEY_VOLUMEUP
0x44
3
VOL-
0x0C
0xea
KEY_VOLUMEDOWN
0x45
4
up
0x0C
0x42
KEY_UP
0x56
5
down
0x0C
0x43
KEY_DOWN
0x50
6
left
0x0C
0x44
KEY_LEFT
0x47
7
right
0x0C
0x45
KEY_RIGHT
0x4B
8
OK
0x0C
0x84
KEY_ENTER
0x57
9
0x0C
0x224
KEY_BACK
0x4A
10
0x0C
0x223
KEY_HOME
0x59
11
0x07
0x95
KEY_MAXHUB_MINI_MIC_CTL
0x11
12
0x07
0x96
KEY_MAXHUB_MINI_ZOOM_PLUS
0x1B
13
0x07
0x97
KEY_MAXHUB_MINI_ZOOM_MINUS
0x0F
14
Do not send code value, short press to switch empty mouse switch function
0x0D
15
AutoFraming
0x07
0x98
KEY_POUND
0x0C
16
Menu
0x0C
0x40
KEY_MENU
0x46
17
Preset bit switching
0x07
0x99
KEY_CVTE_CAM_POS
0x51
18
Turn off the camera
0x07
0x9a
KEY_CVTE_HANGUP
0x09
5) Function Description
(1) The Bluetooth status of the remote control is not connected, and all the keys of the remote control send
infrared code value.
(2) When the remote control has been paired with the equipment, but is not connected, the remote control
initiates the back connection signal by any key, and initiates the active back connection operation with the
current paired Videobar equipment.
(3) When the remote control and Videobar device have been paired and connected, POWER only sends the
infrared code value, not the Bluetooth code value. Other keys only send the Bluetooth code value
6) Remote control pairing
（1）When Bluetooth is not paired (when there is no Bluetooth pairing record), press and hold the Back
button +Home button on the remote control for 3 seconds at the same time, the remote control will send
the infrared code value 0x0b once, and enter the paired broadcast mode. The broadcast time is 2 minutes.
At the same time, the screen pops up the pairing operation prompt:
（2）Press the mouse button. If Bluetooth is not paired, the screen will pop up the
pairing operation prompt, and then the infrared code value will be sent; If paired, is
the normal mouse switch function.
（3）When the remote control has been paired with the Vediobar device but is not connected, press any
button of the remote control to initiate active connection back operation with the current paired Vediobar
device.
(4) After successful pairing, the screen will display a prompt icon indicating successful connection and close
the prompt screen.
（5) If the coding is still unsuccessful within 2 minutes, the remote control will automatically return to the
original state.
(6) When the Bluetooth is paired, press and hold the Back button +Home button on the remote control for 3
seconds, the remote control will clear the pairing information first, then send an infrared code value 0x0A,
close the Bluetooth (no longer initiate pairing broadcast), and the UC terminal will clear the Bluetooth
connection record at the same time.
7) Mouse function description
(1) The empty mouse function is available only when Bluetooth is connected.
(2) The cursor can move smoothly and accurately following the user's actions (whether it is circle drawing,
horizontal movement, vertical movement, acceleration, deceleration, etc.) without unnecessary trajectory or
delay.
(3) When Bluetooth is connected, press the empty mouse button to open or close the empty mouse
function. After opening the empty mouse function, press the OK key to send the left mouse button function.
(4) After the empty mouse is opened, the sensor works normally when the remote control moves; When the
remote control is stationary, the sensor enters the low-power mode.
(5) When the empty rat function is turned on, no operation is performed within 2 minutes, and the empty rat
function is automatically turned off. The sensor goes to sleep. If the empty rat is needed, it needs to be
turned on again.
(6) When the Bluetooth connection to the empty mouse is turned on, the function of the empty mouse will
be turned off by default.
(7) When the empty mouse function is on, if you press the navigation button (up or down or so), the empty
mouse function will be automatically closed and the navigation button will be responded to.
(8) The power display of the remote control shows that: there is a reminder of the battery power on the
interface of Bluetooth remote control connection setting. In addition, the current battery power will be
checked every time the device is turned on. If the battery power is low, there will be a corresponding
reminder:
(9) Under the empty mouse, if you press the navigation button (up or down or so), the mouse function will
be automatically cancelled to respond to the button navigation.
(10) To adjust the sensitivity, long press the confirm key for 2 seconds, and then press the volume +- to
adjust the sensitivity.
8) Others
(1) Bluetooth is turned on by default after the first startup, and Bluetooth pairing is
prompted.
(2) Host pairing triggered by the remote control can be triggered by mouse key (infrared code) or broadcast
(provided that the host Bluetooth is turned on and in scanning state)。
5、Product structure drawing
7、Packing
FCC
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy,
and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.
ISED
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
1) L'appareil ne doit pas produire de brouillage;
2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Cet émetteur ne doit pas être colocalisé ou fonctionner en conjonction avec une autre antenne ou un
autre émetteur.
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.
Le matériel a été évalué pour répondre aux exigences générales d’exposition aux radiofréquences.Le
dispositif peut être utilisé dans des conditions d ‘exposition portables illimitées.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

MAXHUB RC01 Manuel utilisateur

Marque
MAXHUB
Modèle
RC01
Catégorie
Télécommandes
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents