Honeywell Home C1 Wi-Fi Security Camera Guide d'installation

Marque: Honeywell Home

Modèle: C1 Wi-Fi Security Camera

Catégorie: Réveils

Taper: Guide d'installation

Ce manuel convient également à

C1 Wi-Fi Security

Camera

Quick Installation Guide

M37745

RCHC4100WF1002

RCHC4100WF1011

Read before installing.

Input/entrada: 5 V 2 A

Download the Honeywell Home app

NOTE: Have your WiFi password available and confirm your

router communicates at 2.4 GHz before installation.

1 Make sure bluetooth is enabled on your mobile device.

2 Search for Honeywell Home in the App

Store or Google Play.

3 Download the Honeywell Home app.

GET IT ON

Launch the Honeywell

Home app

1 Launch the Honeywell Home app.

2 Create an account (if necessary),

or sign in to your Honewell Home

account. Tap ADD DEVICE or the plus

sign.

3 Select the C1 WiFi Camera to install,

then follow the instructions in the

Honeywell Home app to name the

camera and its location.

Connect the power cord

1 Remove the camera base and

plug the power cord’s USB

end into the camera.

2 Reinsert the camera base

and plug the camera into a

power outlet.

3 Wait until the LED on the

camera blinks blue (about 1

minute), then tap NEXT.

NOTE: If the LED turns solid red,

it means the connection mode

timed out. Unplug the camera and plug it back in.

Installation

Connect

Connect to Wi-Fi

NOTE: Be sure you are on the same WiFi

network you wish to connect your camera

to.

1 Choose your WiFi network from the

list. Tap NEXT.

2 Enter your WiFi password, if

necessary. Tap DONE.

NOTE: The camera will beep during some

steps in this process.

Connect to mobile device

1 Enable bluetooth on your mobile

device.

2 The app will look for the camera.

• For one camera, it will connect

automatically.

• For more than one camera, the app

will prompt you to select one camera

at a time. Each camera has a unique

MAC ID printed on the back. Use

that ID to select the camera you

want to connect.

3 A QR code will display in the app. To

connect your camera to the app, hold the QR code approximately 38

inches (720 cm) from the camera lens.

4 The camera LED turns purple and the camera beeps.

Wi-Fi connection LEDs

During WiFi connection, the LED indicates the following.

LED Camera state

Blinking Green Connecting to WiFi network.

Solid Green Connected to WiFi network.

Solid Red (for 2

seconds)

Connection failed. LED will then turn solid purple.

Solid Purple QR Code scan complete.

Go to “Connect to WiFi” on page 3.

Blinking Blue Camera has lost bluetooth connection. Unplug

camera and plug it back in. See “Connect the power

cord” on page 2 for instructions.

Options

Choose your Geofencing and Membership options (if you skip them you can change

them easily later).

Placement

With stand

Place the camera in a desired location for

viewing and recording.

On the wall

You can also mount the camera directly to

the wall without the stand.

Operation

Remove/replace the stand

The stand is connected to the camera by a magnet.

If you want to remove the stand to hang the camera on

the wall or replace the SD card, simply pull the stand

off of the camera. To replace, just snap it back on the

camera.

Honeywell Home app experience

When you launch the application, your Home screen is

displayed.

All of your devices (cameras, thermostats, water leak

detectors, etc.) are displayed. Select a camera from the

list to view live video from that camera.

Testing smoke/CO alarm detection

If your smoke or carbon monoxide alarm goes off and your camera is on, it

will send you an alert that a smoke or CO alarm has been detected.

To test this feature, press and hold the Test button on your smoke/CO

detector for at least 5 seconds or 3 cycles of the detector’s alarm. A shorter

test might not trigger a sound event.

Camera overview

Stand

Power cord

LED indication

Camera lens

SD card and slotReset hole

Reset

If your WiFi connection fails or you need to connect to a different WiFi network,

insert one end of a paperclip into the reset hole. Press and hold it for 5 seconds to

reset the WiFi connection.

To reset all settings to factory defaults, press and hold the paperclip in the reset

hole for 10 seconds.

SD card

The camera comes with an encrypted 8GB SD card installed. It stores images if the

camera’s connection to the cloud is lost. You can replace it with any compatible

SD card.

Status LED

The camera has an LED that gives device status.

LED Camera state

During installation

Blinking Blue Powered up. Ready to begin setup.

Solid Blue Connected to App. Ready to complete setup.

Solid Purple QR Code scan complete.

Go to “Connect to WiFi” on page 3.

Blinking Green Connecting to WiFi network.

Solid Green Connected to WiFi and operating.

Solid Red Setup timed out. Unplug camera, plug it back in, and

restart the process.

During operation

Blinking Green Connecting to WiFi network.

Solid Green Connected to WiFi and operating.

Blinking Red Not connected to WiFi.

FCC Regulations

§ 15.19 (a)(3)

This device complies with part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

§ 15.21

Changes or modifications not expressly approved by the party responsible for

compliance could void the user‘s authority to operate the equipment.

§ 15.105(b)

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency ener-

gy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the inter-

ference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body.

This device and its antenna(s) must not be co-located or operating in conjunction

with any other antenna or transmitter.

IC Regulations

This device contains license-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s license-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

IC Radiation Exposure Statement:

This equipment complies with IC RSS102 radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator & your body.

FAQ

Why did the camera not detect the smoke alarm

sound when I tested it for compatibility?

The camera is programmed to detect a series of

alarm sounds in case of smoke or ﬁre provided that

the smoke alarm device has beeped or sounded for

at least 5 seconds. When you enable the intelligent

sound detection feature and test the smoke alarm

device, please press-and-hold the Test button on your

smoke alarm device for AT LEAST FIVE SECONDS.

How soon can I get the alert on my app once it’s

detected as a smoke alarm at my home/ofﬁce?

If the camera detected the smoke alarm sound,

our camera will send the notiﬁcation immediately

to you or an approved person on your account. It

normally takes up to 30 seconds for the email and

push notiﬁcations to be sent, but delivery times are

subject to the limitations of your network and WiFi

performance.

How do I get the alert/notiﬁcation of smoke alarm?

If you have the intelligent sound detection feature

enabled, the camera will send the app notiﬁcation

as “Smoke alarm detected from CAM at your HOME/

OFFICE” and send a message to the registered email

address once the alarm sound is detected by the

camera.

What is the minimum distance required to detect

the smoke alarm?

The camera is designed to detect anywhere within

49 feet or 15 meters distance from the sound source

even with door open or closed at your home. Once

you have placed the camera in the desired and

permanent location, you should test the intelligent

sound detection feature with your detector to ensure

normal operation and that the alert is being sent to

the app.

What should the audio sensitivity be set at,

especially for successful smoke alarm detection?

If your camera has been installed within a reasonable

distance (approx. 32.8 feet or 10 meters) of the

detector, you can keep it at normal sensitivity level.

After you place the camera in the desired, permanent

location, you should test the intelligent sound

detection feature with your detector to ensure normal

operation and that the alert is being sent to the app.

How do I conduct a test trial of smoke alarm?

To use the intelligent sound detection feature, you

must ﬁrst test your camera with your detector. To

test the smoke alarm detection functionality, place

the camera in the location where you intend to keep

it and then press Test button on your smoke/ CO

detector and hold for at least 5 seconds or hold until

3 cycles of alarm sounds are heard. Otherwise, the

C1 will not detect the alarm sound. It is especially

important to do this to avoid any false alerts from

other similar sounding devices in your house (like

microwaves, etc.)

Will this camera detect smoke alarm sounds from

devices of all brands? What brands of smoke and

carbon monoxide detectors are recognized by the

Intelligent Sound Detection feature on C1 WiFi

Security Camera?

Camera is compatible with detectors of these

manufacturers: Honeywell, Kidde, Nest, First Alert.

The camera is designed to detect all alarm sounds

which generate alarm sounds for more than 5

seconds. If your detector brand is not that listed

above, you can still test the camera for compatibility

with your detector by following the instructions

above.

Is there a chance to have a high detection rate

if I install this camera facing the smoke alarm

direction?

Our camera microphone is designed to detect the

sound coming from all directions. So, you can place

your camera wherever you want to focus, but follow

the instructions above to ensure compatibility by

testing it the ﬁrst time you use it.

I see that sometimes the camera sends a false

alarm (prompted by sounds from my microwave) as

“smoke detected”, what should I do?

To provide the best experience to the customer, the

camera is programmed to detect any alarm-like

sound. If the false alarm continues try changing

the sensitivity level to “low” in sound conﬁguration

page. In all events, once you change the setting you

will need to re test the camera with your detector to

ensure that it detects the alarm sounds and delivers

an alert to the app.

Will this camera detect the sound if the camera is

installed on the second ﬂoor and the smoke alarm

emanates from ﬁrst ﬂoor?

The camera is designed to detect the smoke alarm

sound as long as the distance of the camera from

the source of the beeping smoke detector is within

49 feet or 15 meters, even if it is partitioned by

glass/ door. You will need to test the camera with

the detector to ensure that it is working and sending

alerts to the app.

Will this camera always listen for smoke alarm

sound AND any other sound detection as well?

We programmed the camera to detect any sound

which meets certain criteria on the sensitivity level

at which you conﬁgured the camera. The camera

will send the smoke alert notiﬁcation if the detected

sound gets classiﬁed as a smoke alarm (based on

internal libraries), otherwise the camera will send out

the notiﬁcation simply as “sound detected”.

Can I program my camera to receive audio alerts

from beeping smoke alarms only, and no other

audio sounds?

Not right now. However, we continue to upgrade the

App features and this customization could be part of

future releases of the App.

My camera keeps sending me many sound detected

alert notiﬁcations every day. What should I do? Is

there a way to avoid this?

As our camera’s microphone sensitivity is very sharp,

it will report whatever audio it hears and discerns in

your premises. To avoid getting inundated with many

notiﬁcations, you can adjust the audio sensitivity

level and set it as “Low” on our sound conﬁguration

page on the app. Once you change the audio

sensitivity level you should retest the detector and

camera to ensure that the intelligent sound detection

feature is working and that alerts are being sent to

the app.

My camera is working ﬁne, but I hear no audio in

the stored video clip. Why?

Please check if the volume on your smart device

is turned on. If the volume on your smart device is

set correctly, and you still don’t hear audio in your

video clip, try power cycling the camera (unplug the

camera’s power outlet, wait for about 30 seconds and

power the camera back on. Wait for the camera to

reboot, and that should solve the problem).

What will the camera do next, once it detected

beeping smoke alarm sound? Will it also send a

message to a ﬁre station?

As this is a DoItYourself camera, it would not notify

ﬁre station. For further peace of mind, you can

upgrade to professionally monitored security from

Resideo.

The camera will send you an in-app and email

notiﬁcation like any other audio or motion detected

event. It could take up to 30 seconds or more, subject

to your network and WiFi performance, for the

notiﬁcations to be sent across. The camera would

also generate a 30 second video clip that can be

accessed via the App.

Are these cameras recording everything and

sending to any other private cloud service?

No. Unlike other products on the market, our

cameras do not hog your bandwidth with continuous

recording. We also take customer data privacy

and security seriously and provide end to end

encryption and security in our cameras and cloud

implementation, which includes AES 256 encryption,

hardware authentication crypto-encryption, secure

session and streaming authentication, etc.

The cameras are designed to detect any suspicious

motion and/or any sound (including smoke alarm

sound) at your home. The detection algorithm

operates on the camera ﬁrmware and the

notiﬁcations are relayed to you via the cloud.

In the event of a motion or audio detected event, only

detected sound will be recorded for 30 seconds and

sent to the cloud for you to view the clips through

your App or download the clip to your smart device

memory as required.

How long will it take to create recorded video,

once the camera detects smoke alarm or any other

sound?

The process starts almost immediately, but it could

33-00407EFS-05

www.resideo.com

The Honeywell Home trademark is used under license from

Honeywell International, Inc. This product is manufactured by

Resideo Technologies, Inc. and its affiliates.

utilisée avec l’autorisation d’Honeywell International, Inc. Ce produit

est fabriqué par Resideo Technologies, Inc. et ses sociétés affiliées.

se utiliza bajo licencia de Honeywell International, Inc. Este producto

es fabricado por Resideo Technologies, Inc. y sus afiliados.

Resideo Technologies, Inc.

1985 Douglas Drive North, Golden Valley, MN 55422

1-800-633-3991

33-00407EFS—05 M.S. Rev. 04-21 | Printed in United States

take 30 seconds or longer depending on your network and WiFi performance to view the new clips on your

Honeywell Home App.

My smoke detector is 10/20 years old. Will this camera detect the sound?

It should, but you should test the compatibility of the detector and the camera before ﬁrst use by following the

testing procedure described in this FAQ.

Need help?

• Web: resideo.com

• Phone: 18006333991

The operation of this equipment

is subject to the following two

conditions: (1) this equipment

or device may not cause harmful

interference, and (2) this

equipment or device must accept

any interference, including

interference that may cause

undesired operation.

M37745

RCHC4100WF1002

RCHC4100WF1011

Lire avant l’installation.

ENTRÉE : 5 V 2 A

Guide d’installation

rapide

Caméra de sécurité

Wi-Fi C1

Téléchargez l’application Honeywell Home

REMARQUE : Ayez en main le mot de passe du réseau WiFi et assurez-vous que

le routeur est réglé sur une fréquence de 2,4 GHz.

1 Assurez-vous que Bluetooth est activé sur

votre appareil mobile.

2 Cherchez Honeywell Home dans l’App Store

ou sur Google Play.

3 Téléchargez l’application Honeywell Home.

Lancez l’application

Honeywell Home

1 Lancez l’application Honeywell Home.

2 Créez un compte (si nécessaire)

ou connectez-vous à votre compte

Honeywell Home. Appuyez sur AJOUTER

UN APPAREIL ou sur le signe plus (+).

3 Sélectionnez la caméra WiFi C1 à

installer, puis suivez les instructions

de l’application Honeywell Home

pour nommer la caméra et son

emplacement

Branchez le cordon d’alimentation

1 Retirez le socle de la caméra et branchez l’embout USB du cordon

d’alimentation à la caméra.

2 Remettez le socle sous la

caméra et branchez le cordon

d’alimentation à une prise

électrique.

3 Attendez environ 1 minute

que le voyant DEL devienne

bleu et clignote, puis touchez

NEXT (SUIVANT).

REMARQUE : Si le voyant DEL

devient rouge fixe, cela signifie

que le mode de connexion est expiré. Débranchez et rebranchez la caméra.

Installation

Connexion

Connexion à un réseau

Wi-Fi

REMARQUE : Assurez-vous d’être connecté

au même réseau WiFi que celui auquel

vous souhaitez connecter votre caméra.

1 Sélectionnez votre réseau WiFi à partir

de la liste. Touchez NEXT (SUIVANT).

2 Entrez le mot de passe du réseau WiFi,

au besoin. Touchez DONE (TERMINÉ).

REMARQUE : La caméra émet des signaux

sonores à certaines étapes de la procédure.

Connexion à un appareil mobile

1 Activez Bluetooth sur votre appareil

mobile.

2 L’application recherche la caméra.

• Pour une seule caméra, la connexion

se fait automatiquement.

• Lorsqu’il y a plusieurs caméras,

l’application vous demande de

sélectionner une caméra à la fois.

Chaque caméra possède une

adresse MAC unique imprimée au

dos. Utilisez cette adresse pour

sélectionner la caméra que vous

désirez connecter.

3 L’application afﬁche un code QR. Pour

connecter la caméra à l’application,

maintenez le code QR à une distance

de 7 à 20 cm (de 3 à 8 pouces) devant l’objectif de la caméra.

4 Lorsque la connexion est réussie, le voyant DEL devient mauve et la

caméra émet un signal sonore.

Voyant DEL lors de la connexion Wi-Fi

Lors de la connexion au réseau WiFi, le voyant DEL indique l’état de la caméra.

DEL État de la caméra

Vert clignotant Connexion au réseau WiFi.

Vert ﬁxe Connexion au réseau WiFi.

Rouge ﬁxe

(pendant 2

secondes)

Échec de la connexion. Le voyant DEL devient ensuite

mauve ﬁxe.

Mauve ﬁxe Balayage du code QR terminé. Go to « Connexion à un

réseau WiFi », à la page 3.

Bleu clignotant La connexion Bluetooth a été perdue. Débranchez et

rebranchez la caméra. Reportez-vous aux instructions

de la section « Branchez le cordon d’alimentation », à la

page 2.

Options

Choisissez les options Geofence et les options d’adhésion (si vous sautez cette

étape, vous pouvez facilement modiﬁer ces options plus tard).

Placement

Avec le socle

Placez la caméra à l’endroit souhaité.

Sur le mur

Vous pouvez également fixer la caméra directe-

ment sur un mur, sans le socle

Fonctionnement

Enlever ou remettre le socle en place

Le socle est connecté à la caméra par un aimant.

Si vous voulez enlever le socle pour ﬁxer la caméra à un mur

ou remplacer la carte SD, détachez simplement le socle de

la caméra. Pour le remettre, il sufﬁt de le replacer sous la

caméra.

Fonctionnement de l’application

Honeywell Home

Lorsque vous lancez l’application, la page d’accueil s’afﬁche.

Tous vos appareils (caméras, thermostats, détecteurs de

fuites d’eau, etc.) sont afﬁchés. Sélectionnez une caméra pour

visionner son signal vidéo en direct.

Test de détection de l’alarme du détecteur de

fumée ou de monoxyde de carbone

Si l’alarme de votre détecteur de fumée ou de monoxyde de carbone se déclenche

et que votre caméra est activée, vous recevrez une alerte vous avisant qu’une

alarme du détecteur de fumée ou de monoxyde de carbone a été détectée.

Pour tester cette fonction, maintenez enfoncé le bouton de test de votre détecteur

de fumée ou de monoxyde de carbone pendant au moins cinq secondes ou trois

cycles d’alarme du détecteur. Un test plus court pourrait ne pas déclencher le son.

Pour voir la liste d’alarmes compatibles, visitez le site Resideo.com.

Aperçu de la caméra

Socle

Câble

d’alimentation

Voyant DEL

Objectif de la

caméra

Fente et

carte SD

Bouton de

réinitialisation

Réinitialisation

Si la connexion WiFi est interrompue ou si vous devez vous connecter à un réseau

différent, pressez le bouton de réinitialisation en insérant l’extrémité d’un trom-

bone dans l’ouverture. Maintenez-le enfoncé pendant 5 secondes pour réinitialiser

la connexion WiFi.

Pour restaurer les paramètres par défaut, maintenez le trombone enfoncé dans

l’ouverture pendant 10 secondes.

Carte SD

Une carte SD chiffrée de 8 Go est préinstallée dans la caméra. Celle-ci enregistre

les images si la connexion au nuage est interrompue. Vous pouvez la remplacer

avec n’importe quelle autre carte SD compatible.

Voyant DEL d’état

La caméra est munie d’un voyant DEL indiquant son état.

DEL État de la caméra

Pendant l’installation

Bleu clignotant Allumée. Prête à commencer l’installation.

Bleu ﬁxe Connectée à l’application. Prête à terminer la

conﬁguration.

Mauve ﬁxe Balayage du code QR terminé.

Go to « Connexion à un réseau WiFi », à la page 3.

Vert clignotant Connexion au réseau WiFi.

Vert ﬁxe Connectée au réseau WiFi et en état de marche.

Rouge ﬁxe Délai de conﬁguration expiré. Débranchez et

rebranchez la caméra, puis recommencez la procédure.

En fonctionnement

Vert clignotant Connexion au réseau WiFi.

Vert ﬁxe Connectée au réseau WiFi et en état de marche.

Rouge

clignotant

Non connectée au réseau WiFi.

Règlements de la FCC

§ 15.19 (a)(3)

Cet appareil est conforme à la partie 15 des règlements de la FCC. Son fonctionne-

ment est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer

d’interférences nuisibles et (2) doit accepter toutes les interférences reçues, nota-

mment celles à l’origine d’un fonctionnement indésirable.

§ 15.21

Les modifications qui ne sont pas expressément autorisées par la partie respons-

able de la conformité peuvent annuler le droit de l’utilisateur à utiliser l’appareil.

Les modifications qui ne sont pas expressément autorisées par la partie respons-

able de la conformité peuvent annuler le droit de l’utilisateur à utiliser l’appareil.

§ 15.105(b)

Cet équipement a subi des tests prouvant sa conformité aux limites prescrites

pour les appareils numériques de classe B, selon la partie 15 des règlements de la

FCC. Ces limites ont été conçues pour fournir une protection raisonnable contre

les interférences nuisibles lorsque l’appareil est utilisé dans un environnement rés-

identiel. Cet équipement génère, utilise et peut émettre de l’énergie radiofréquence

et, s’il n’est pas installé et utilisé conformément aux instructions, peut causer des

interférences nuisibles aux communications radio. Toutefois, il n’y a aucune garan-

tie que ces interférences ne puissent survenir dans une installation donnée. Si cet

équipement cause des interférences nuisibles à la réception de signaux de radio ou

de télévision, ce qui peut être déterminé en l’éteignant et en l’allumant, l’utilisateur

peut essayer de corriger ces interférences par les mesures suivantes :

• Réorienter ou déplacer l’antenne réceptrice.

• Augmenter la distance entre l’équipement et le récepteur.

• Brancher l’équipement sur un circuit différent de celui sur lequel le récepteur est

branché.

• Consulter le détaillant ou un technicien expérimenté en radio/télévision.

La page charge ...

Honeywell Home C1 Wi-Fi Security Camera Guide d'installation

Marque: Honeywell Home

Modèle: C1 Wi-Fi Security Camera

Catégorie: Réveils

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Honeywell Home C1 Wi-Fi Security Camera Installation guide
español: Honeywell Home C1 Wi-Fi Security Camera Guía de instalación

Honeywell Home C1 Wi-Fi Security Camera Guide d'installation

Ce manuel convient également à

Honeywell Home C1 Wi-Fi Security Camera Guide d'installation

dans d''autres langues

Documents connexes

Autres documents