Hitachi DH 18DBL Manuel utilisateur

Marque: Hitachi

Modèle: DH 18DBL

Catégorie: Perceuses électriques

Taper: Manuel utilisateur

Model

Modèle

Modelo

DH 18DBL

Cordless Rotary Hammer

Marteau rotatif sans ﬁ l

Martillo perforador a batería

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should be

stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

English

Page Page

Français

Page Page

Español

Página Página

TABLE DES MATIÈRES

ÍNDICE

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ..............3

MEANINGS OF SIGNAL WORDS ........................3

SAFETY...................................................................3

GENERAL POWER TOOL SAFETY

WARNINGS ...................................................3

SPECIFIC SAFETY RULES AND SYMBOLS .......5

IMPORTANT SAFETY INSTRUCTIONS FOR USE

OF THE

CORDLESS ROTARY HAMMER .....6

IMPORTANT SAFETY INSTRUCTIONS FOR

BATTERY CHARGER ....................................6

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF

THE BATTERY AND BATTERY CHARGER

.........7

CAUTION ON LITHIUM-ION BATTERY ...............7

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION ......................................8

FUNCTIONAL DESCRIPTION ...............................9

NAME OF PARTS .................................................9

SPECIFICATIONS ..............................................10

ASSEMBLY AND OPERATION ............................11

APPLICATIONS ..................................................11

REMOVAL AND INSTALLATION METHOD

OF BATTERY ...............................................11

CHARGING METHOD ........................................11

BEFORE USE .....................................................13

PRIOR TO OPERATION .....................................13

HOW TO USE .....................................................15

OPERATIONAL CAUTIONS ...............................18

REACTIVE FORCE CONTROL ..........................18

MAINTENANCE AND INSPECTION ....................19

ACCESSORIES ....................................................21

STANDARD ACCESSORIES .............................21

OPTIONAL ACCESSORIES ...............................21

PARTS LIST ..........................................................65

CONSIGNES DE SÉCURITÉ IMPORTANTES ...23

SIGNIFICATION DES MOTS D’AVERTISSEMENT

....23

SÉCURITÉ ............................................................23

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

CONCERNANT LES OUTILS ÉLECTRIQUES

....23

REGLES DE SECURITE SPECIFIQUES ET

SYMBOLES .................................................25

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DU MARTEAU

ROTATIF SANS FIL .....................................26

CONSIGNES DE SÉCURITÉ IMPOR TANTES

POUR LE CHARGEUR DE BATTERIE ........26

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L’UTILISATION DE LA BATTERIE ET DU

CHARGEUR DE BATTERIE ................................27

PRÉCAUTIONS RELATIVES A LA BATTERIE AU

LITHIUM ION .......................................................28

À PROPOS DU TRANSPORT DE LA BATTERIE

LITHIUM-ION

.................................................29

DESCRIPTION FONCTIONNELLE ......................30

NOM DES PARTIES ...........................................30

SPECIFICATIONS ..............................................31

ASSEMBLAGE ET FONCTIONNEMENT .............32

UTILISATIONS ...................................................32

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .........................................32

MÉTHODE DE RECHARGE ...............................32

AVANT L’UTILISATION ......................................34

AVANT LA MISE EN MARCHE ...........................34

COMMENT UTILISER ........................................37

PRECAUTIONS DE FONCTIONNEMENT .........39

COMMANDE DE FORCE RÉACTIVE .................39

ENTRETIEN ET INSPECTION .............................40

ACCESSOIRES ....................................................42

ACCESSOIRES STANDARD .............................42

ACCESSOIRES EN OPTION ..............................42

LISTE DES PIÈCES ..............................................65

INSTRUCCIONES IMPORTANTES SOBRE

SEGURIDAD ...............................................44

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ...........................................44

SEGURIDAD .........................................................44

ADVERTENCIAS DE SEGURIDAD GENERAL DE LA

HERRAMIENTA ELÉCTRICA

...........................44

NORMAS Y SÍMBOLOS ESPECÍFICOS DE

SEGURIDAD ................................................46

INSTRUCCIONES IMPORTANTES PARA LA

UTILIZACIÓN DEL MARTILLO PERFORADOR A

BATERÍA

.......................................................47

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

..............47

INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA

LA BATERÍA Y EL CARGADOR DE BATERÍAS

.....48

ADVERTENCIA DE LA BATERÍA DE LITIO ........49

A PROPÓSITO DEL TRANSPORTE DE LA

BATERÍA DE IONES DE LITIO ....................50

DESCRIPCIÓN FUNCIONAL ...............................51

NOMENCLATURA ..............................................51

ESPECIFICACIONES .........................................52

MONTAJE Y OPERACIÓN ...................................53

APLICACIONES .................................................53

MÉTODO DE EXTRACCIÓN E INSTALACIÓN DE

LA BATERÍA.................................................53

MÉTODO DE CARGA .........................................53

ANTES DE LA UTILIZACIÓN ..............................55

ANTES DE LA OPERACIÓN...............................55

INSTRUCCIONES DE USO ................................57

PRECAUCIONES OPERACIONALES ................60

CONTROL DE FUERZA REACTIVA ...................60

MANTENIMIENTO E INSPECCIÓN .....................61

ACCESSORIOS ....................................................63

ACCESORIOS ESTÁNDAR ................................63

ACCESORIOS OPCIONALES ............................63

LISTA DE PIEZAS ................................................65

English

IMPORTANT SAFETY INSTRUCTIONS

Read all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or

maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the "SAFETY" section of this Instruction Manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power

tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

English

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personal

injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your ﬁ nger on the switch

or energising power tools that have the switch on

invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be caught

in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk of

injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.

Shorting the battery terminals together may cause

burns or a ﬁ re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause irritation

or burns.

6) Service

a) Have your power tool serviced by a

quali

ﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

–WARNING–

To reduce the risk of injury, user must read

instruction manual.

English

WARNING

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities

contains chemicals known to the State of California

to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

●

Lead from lead-based paints,

●

Crystalline silica from bricks and cement and

other masonry products, and

●

Arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to

ﬁ lter out microscopic particles.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Wear ear protectors with impact drilling.

Exposure to noise can cause hearing loss.

2. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

3. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live”and could

give the operator an electric shock.

4. NEVER place hands or other body parts near the

drill bit or chuck during operation. Hold the drill by its

handle only.

5. Because the cordless tool operates by battery power,

be aware of the fact that it can begin to operate at any

time.

6. When working at elevated locations, clear the area

of all other people and be aware of conditions below

you.

7. NEVER touch moving parts.

NEVER place your hands, ﬁ ngers or other body parts

near the tool’s moving parts.

8. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard or

safety feature before resuming operation of the tool.

9. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

10. NEVER use a power tool for applications other

than those speciﬁ ed.

NEVER use a power tool for applications other than

those speciﬁ ed in the Instruction Manual.

11. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

12. Deﬁ nitions for symbols used on this tool

V .............volts

—

---

...........direct current

no ...........no load speed

---/min .....revolutions or reciprocation per minute

13. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

14. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

15. Blades and accessories must be securely

mounted to the tool.

Prevent potential injuries to yourself or others. Blades,

cutting implements and accessories which have been

mounted to the tool should be secure and tight.

16. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually, making

strange noises, or otherwise appears defective, stop

using it immediately and arrange for repairs by a

Hitachi authorized service center.

17. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

18. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

19. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that

air can freely ﬂ ow at all times. Check for dust build-up

frequently.

20. ALWAYS wear eye protection that meets the

requirement of the latest revision of ANSI

Standard Z87.1.

English

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC input rating Ampere* AWG size of cord

Equal to or

greater than

but less

than

Length of cord, feet (meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

* If the input rating of a battery charger is given in watts

rather than in amperes, the corresponding ampere

rating is to be determined by dividing the wattage

rating by the voltage rating―for example:

1,250 watts

= 10 amperes

125 volts

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE CORDLESS ROTARY

HAMMER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of the cordless rotary

hammer. To avoid these risks, follow these basic

safety instructions:

1. NEVER touch the tool bit with bare hands after

operation.

2. NEVER wear gloves made of stuﬀ liable to roll up

such as cotton, wool cloth or string, etc.

3. ALWAYS attach the side handle and securely grip the

Cordless Rotary Hammer.

4. ALWAYS be careful with buried object such as an

underground, wiring.

Touching these active wiring or electric cable with this

tool, you may receive an electric shock.

Conﬁ rm if there are any buried object such as electric

cable within the wall, ﬂ oor or ceiling where you are

going to operate here after.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers.

To avoid these risks, follow these basic safety

instructions:

Battery and battery charger are not included with this

product

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YFSL.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable

battery type BSL18 series. Other type of batteries

may burst causing personal injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of ﬁ re, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

7. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

8. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁ ed in Table 1.

9. Do not operate battery charger with damaged cord or

plug-replace them immediately.

10. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

11. Do not disassemble battery charger; take it to a

qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

English

12. To reduce risk of electric shock, unplug charger from

receptacle before attempting any maintenance or

cleaning. Removing the battery will not reduce this

risk.

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER

You must charge the battery before you can use the power

tool. Before using the model UC18YFSL battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

CAUTION

USE ONLY HITACHI BATTERY TYPE BSL1850.

OTHER TYPES OF BATTERIES MAY BURST AND

CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING

Improper use of the battery or battery charger

can lead to serious injury. To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or

is completely worn out. The battery can explode in a

ﬁ re.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s

air vents. Electric shock or damage to the battery

charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F

(0°C) or above 104°F (40°C).

Charging the battery at temperatures outside the

range of 32°F – 104°F (0°C – 40°C) may prevent

proper charging and reduce battery life.

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to

charge.

11. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C).

12. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

14. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat

generation, smoke emission, explosion and ignition

beforehand, please be sure to heed the following

precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

8. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

9. Keep away from ﬁ re immediately when leakage or foul

odor are detected.

English

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or store

by securely pressing into the battery cover until

the ventilation holes are concealed to prevent

short-circuits (See Fig. 2).

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations of

the destination country.

Power Output

2 to 3 digit number

Fig. 1

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have ﬁ rst read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless Rotary Hammer (DH18DBL)

Battery, battery charger are not included with this product.

Depth gauge

Grip

Change lever

Push button

Switch trigger

Battery

(optional accessories)

Nameplate

Front cap

Side handle

Remaining battery

indicator switch

Remaining battery

indicator lamp

Handle

Switch Panel

○

Battery (BSL1850)

Latch

Ventilation holes

Terminals

Battery cover

Battery

Fig. 2

LED Light

English

2 Battery Charger (UC18YFSL)

Battery, battery charger are not included with this product.

Pilot lamp

Guide rail

Nameplate

Cord

Fig. 3

SPECIFICATIONS

1. Cordless Rotary Hammer (DH18DBL)

Model DH18DBL

Voltage 18 V

No- Load speed 0 – 1,050 /min

Full- Load impact rate 0 – 3,950 /min

Capacity Drilling

Concrete 1" (26 mm)

Steel 1/2" (13 mm)

Wood 1 – 1/16" (27 mm)

Type of motor Fan-cooled DC brushless motor

Weight 8.2 lbs. (3.7 kg)

2. Battery Charger (UC18YFSL) (optiopnal accessories...sold separately)

Model UC18YFSL

Input power source Single phase: AC 120 V 60 Hz

Charger

Charging voltage DC 14.4 V – 18 V

Charging current DC 3.5 A

Weight 1.1 lbs. (0.5 kg)

English

ASSEMBLY AND OPERATION

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on the

nameplate, the charger will burn up.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s pilot

lamp will blink in red. (At 1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 5 .

Battery

Pilot lamp

Charger

Fig. 5

3. Charging

When the battery is connected to the battery charger,

charging will commence and the pilot lamp will light in

red. (See Table 2)

NOTE

If the pilot lamp ﬂ ikers in red, pull out the plug from

the receptacle and check if the battery is properly

mounted.

When the battery is fully charged, the pilot lamp

will blink in red slowly. (At 1-second intervals) (See

Table 2)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 2, according to the condition of the charger or

the rechargeable battery.

APPLICATIONS

Rotation and hammering function

○

Drilling anchor holes

○

Drilling holes in concrete

○

Drilling holes in tile

Rotation only function

○

Drilling in steel or wood (with optional accessories)

○

Tightening machine screws, wood screws

(with optional accessories)

Hammering only function

○

Light-duty chiselling of concrete, groove digging and

edging.

REMOVAL AND INSTALLATION METHOD

OF BATTERY

Battery and battery charger are not included with this

product.

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery (See Fig. 4).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 4).

Battery

Pull out

Push

Latch

Insert

Fig. 4

CHARGING METHOD

Battery and battery charger are not included with this

product.

NOTE

Before plugging into the receptacle, make sure the

following points.

○

The power source voltage is stated on the

nameplate.

○

The cord is not damaged.

English

Table 2

Indications of the pilot lamp

Pilot lamp

(red)

Before

charging

Blinks

Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

While

charging

Lights

Lights continuously

Charging

complete

Blinks

Lights for 0.5 seconds. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

Overheat

standby

Blinks

Lights for 1 second. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

Battery overheated.

Unable to charge.

(Charging will commence

when battery cools)

Charging

impossible

Flickers

Lights for 0.1 seconds. Does not light for

0.1 seconds. (oﬀ for 0.1 seconds)

Malfunction in the battery or

the charger

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are as

shown in the Table 3, and batteries that have become

hot should be cooled for a while before being recharged.

Table 3 Recharging ranges of batteries

Rechargeable

battery

Temperatures at which the

battery can be recharged

BSL1850

32°F – 122°F

(0°C – 50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time (At 20°C)

Charger

Battery

UC18YFSL

BSL1850 Approx. 75 min.

NOTE

The charging time may vary according to temperature

and power source voltage.

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

NOTE

After operation, pull out batteries from the charger

ﬁ rst, and then keep the batteries properly.

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated

because it has been left for a long time in a

location subject to direct sunlight or because

the battery has just been used, the pilot lamp of

the charger lights for 1 second, does not light for

0.5 seconds (oﬀ for 0.5 seconds). In such a case,

ﬁ rst let the battery cool, then start charging.

●

When the pilot lamp ﬂ ikers rapidly in red (at

0.2–second intervals), check for and take out

any foreign objects in the charger's battery

connector. If there are no foreign objects,

it is probable that the battery or charger is

malfunctioning. Take it to your authorized

Service Center.

English

●

Since the built-in micro computer takes about

3 seconds to conﬁ rm that the battery being

charged with charger is taken out, wait for a

minimum of 3 seconds before reinserting it to

continue charging. If the battery is reinserted

within 3 seconds, the battery may not be properly

charged.

●

If the pilot lamp does not blink in red (every

second) even though the charger cord is

connected to the power, it indicates that

the protection circuit of the charger may be

activated.

Remove the cord or plug from the power and

then connect it again after 30 seconds or so. If

this does not cause the pilot lamp to blink in red

(every second), please take the charger to the

Hitachi Authorized Service Center.

BEFORE USE

Check the work area to make sure that it is clear of debris

and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

PRIOR TO OPERATION

1. Conﬁ rming condition of the environment

Conﬁ rm that the work site is placed under appropriate

conditions conforming to prescribed precautions.

2. Attaching the side handle (Fig. 6)

(1) Turn the grip of the side handle to loosen it and push it

in until it comes in contact with the housing.

(2) Adjust the side handle to the angle that allows the

easiest use, then turn the side handle’s grip ﬁ rmly to

lock it place.

Loosen

Tighten

Fig. 6

3. Mounting the drill bit (Fig. 7,8)

CAUTION

To prevent accidents, make sure to turn the

switch oﬀ .

NOTE

When using tools such as drill bits, etc., make sure to

use the genuine parts designated by our company.

(1) Clean the shank portion of the drill bit.

(2) Insert the drill bit in a twisting manner into the tool

holder until it latches itself. (Fig. 7)

The grip need not be adjusted during bit installation.

Drill bit

Grip

Part of SDS-plus shank

Front cap

Fig. 7

(3) Check the latching by pulling on the drill bit.

(4) To remove the drill bit, fully pull the grip in the direction

of the arrow and pull out the drill bit. (Fig. 8)

Drill bit

Grip

Fig. 8

4. Installation of dust cup or dust collector (B) (Optional

accessories) (Fig. 9, Fig. 10)

When using a rotary hammer for upward drilling

operations attach a dust cup or a dust collector (B)

to collect dust or particles for easy operation.

○

Installing the dust cup

Use the dust cup by attaching to the drill bit as shown

in Fig. 9.

When using a bit which has big diameter, enlarge the

center hole of the dust cup with this rotary hammer.

○

Installing dust collector (B)

When using dust collector (B), insert dust collector (B)

from the tip of the bit by aligning it to the groove on the

grip. (Fig. 10)

English

Dust cap

Fig. 9

Dust collector (B)

Fig. 10

CAUTION

●

The dust cup and dust collector (B) are for

exclusive use of concrete drilling work. Do not

use them for wood or metal drilling work.

●

Insert dust collector (B) completely into the

chuck part of the main unit.

●

When turning the rotary hammer on while

dust collector (B) is detached from a concrete

surface, dust collector (B) will rotate together

with the drill bit. Make sure to turn on the switch

after pressing dust cup on the concrete surface.

When using dust collector (B) attached to a

drill bit that has more than 7-15/32" (190 mm) of

overall length, dust collector (B) cannot touch

the concrete surface and will rotate. Therefore,

please use dust collector (B) by attaching to drill

bits which have 6-17/32" (166 mm), 6-19/64" (160

mm), and 4-21/64" (110 mm) overall length.

●

Dump particles after every two or three holes

when drilling.

●

Please replace the drill bit after removing dust

collector (B).

5. Selecting the driver bit

Screw heads or bits will be damaged unless a bit

appropriate for the screw diameter is employed to

drive in the screws.

6. Conﬁ rm the direction of bit rotation (Fig. 11)

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the push button. (Fig. 11)

The L-side of the push button is pushed to turn the bit

counterclockwise.

Push button

Fig. 11

CAUTION

The push button cannot be switched while the

power tool is turning. To switch the push button,

stop the power tool, then set the push button.

7 About remaining battery indicator

When pressing the remaining battery indicator switch,

the remaining battery indicator lamp lights and the

battery remaining power can be checked. (Fig.12)

When releasing your ﬁ nger from the remaining battery

indicator switch, the remaining battery indicator lamp

goes oﬀ . The Table 5 shows the state of remaining

battery indicator lamp and the battery remaining

power.

Table 5

State of lamp Battery Remaining Power

The battery remaining power is

enough.

The battery remaining power is

a half.

The battery remaining power is

nearly empty.

Re-charge the battery soonest

possible.

As the remaining battery indicator shows somewhat

diﬀ erently depending on ambient temperature and

battery characteristics, read it as a reference.

English

Remaining battery

indicator lamp

Fig. 12

NOTE

○

Do not give a strong shock to the switch panel or

break it. It may lead to a trouble.

○

To save the battery power consumption, the

remaining battery indicator lamp lights while pressing

the remaining battery indicator switch.

8. How to use the LED light

While the switch is pulled, the LED light will

automatically light up the tip portion of the tool.

(Fig. 13)

The LED light will automatically turn oﬀ 10 seconds

after the switch is released.

Switch trigger

Fig. 13

CAUTION

●

Do not expose directly your eye to the light by

looking into the light.

If your eye is continuously exposed to the light,

your eye will be hurt.

●

Wipe oﬀ any dirt or grime attached to the lens of

the LED light with a soft cloth, being careful not

to scratch the lens.

Scratches on the lens of the LED light can result

in decreased brightness.

9. Selecting the function mode

You can switch functions to the 3 modes of “hammering

only”, “rotation + hammering”, and “rotation only”

by turning the change lever while pressing the push

button. Set the

mark position of the change lever

to that of the mode to be used.

CAUTION

●

Before operating the change lever, check and

make sure that the motor has stopped.

A failure can occur if it is operated while the

motor is running.

●

To operate the change lever, press the push

button, and release the lock of the change lever.

Also, check and make sure after operation

that the push button has returned and that the

change lever has been locked.

●

Switch the change lever without mistake.

If it is used at a position halfway, there is a fear

that the service life of the switching mechanism

may be shortened.

HOW TO USE

CAUTION

●

To prevent accidents, make sure to turn the

switch oﬀ and disconnect the battery when the

drill bits and other various parts are installed

or removed. The power switch should also be

turned oﬀ during a work break and after work.

CAUTION on lithium-ion battery

●

To extend the lifetime, the lithium-ion battery

equips with the protection function to stop the

output. Therefore, if the tool is overloaded, the

motor may stop. However, this is not the trouble

but the result of protection function. In this case,

release the switch of tool and eliminate the

causes of overloading.

1. Switch operation

○

When the switch trigger is depressed, the tool rotates.

When the switch trigger is released, the tool stops.

○

The rotational speed of the rotary hammer can be

controlled by varying the amount that the switch

trigger is pulled. Speed is low when the switch trigger

is pulled slightly and increases as the switch trigger is

pulled more.

○

When releasing the switch trigger, the brake will be

applied for immediate stopping.

Remaining battery

indicator switch

English

2. Rotation + hammering

This rotary hammer can be set to rotation and

hammering mode by pressing the push button and

turning the change lever to the

mark (Fig. 14).

Push button

Change lever

Fig. 14

(1) Mount the drill bit.

(2) Pull the trigger switch after applying the drill bit tip to

the drilling position (Fig.15).

Fig. 15

(3) Pushing the rotary hammer forcibly is not necessary

at all. Pushing slightly so that drill dust comes out

gradually is suﬃ cient.

CAUTION

●

When the drill bit touches construction iron

bar, the bit will stop immediately and the rotary

hammer will react to revolve. Therefore please

grip the side handle and handle tightly as shown

in Fig. 15.

3. Rotation only

This rotary hammer can be set to rotation only mode

by pressing the push button and turning the change

lever to the

mark (Fig. 16).

To drill wood or metal material using the drill chuck

and chuck adapter (optional accessories), proceed as

follows.

Installing drill chuck and chuck adapter. (Fig. 17)

Push button

Change lever

Fig. 16

(1) Attach the drill chuck to the chuck adapter.

(2) The part of the SDS-plus shank is the same as the drill

bit. Therefore, refer to the item of “Mounting the drill

bit” for attaching it.

Front cap

Part of SDS-plus shank

Drill chuck

Grip

Chuck adapter

Fig. 17

CAUTION

●

Application of force more than necessary will not

only expedite the work, but will deteriorate the

tip edge of the drill bit and reduce the service life

of the rotary hammer in addition.

●

Drill bits may snap oﬀ while withdrawing

the rotary hammer from the drilled hole. For

withdrawing, it is important to use a pushing

motion.

●

Do not attempt to drill anchor holes or holes in

concrete with the machine set in the rotation

only function.

●

Do not attempt to use the rotary hammer in

the rotation and striking function with the drill

chuck and chuck adapter attached. This would

seriously shorten the service life of every

component of the machine.

4. When driving machine screws (Fig. 18)

First, insert the bit into the socket in the end of chuck

adapter (D).

Next, mount chuck adapter (D) on the main unit using

procedures described in 3 (1), (2), (3), put the tip of the

bit in the slots in the head of the screw, grasp the main

unit and tighten the screw.

Bit

Socket

Chuck adapter(D)

Front cap

Grip

Fig. 18

English

CAUTION

●

Exercise care not to excessively prolong driving

time, otherwise, the screws may be damaged by

excessive force.

●

Apply the rotary hammer perpendicularly to the

screw head when driving the screw; otherwise,

the screw head or bit will be damaged, or driving

force will not be fully transferred to the screw.

●

Do not attempt to use the rotary hammer in the

rotation and striking function with the chuck

adapter and bit attached.

5. When driving wood screws (Fig. 18)

(1) Selecting a suitable driver bit

Employ plus-head screws, if possible, since the driver

bit easily slips oﬀ the heads of minus-head screws.

(2) Driving in wood screws.

○

Prior to driving in wood screws, make pilot holes

suitable for them in the wooden board.

Apply the bit to the screw head grooves and gently

drive the screws into the holes.

○

After rotating the rotary hammer at low speed for a

while until the wood screw is partly driven into the

wood, squeeze the trigger more strongly to obtain the

optimum driving force.

CAUTION

Exercise care in preparing a pilot hole suitable

for the wood screw taking the hardness of the

wood into consideration. Should the hole be

excessively small or shallow, requiring much

power to drive the screw into it, the thread of the

wood screw may sometimes be damaged.

6. Hammering only

This rotary hammer can be set to hammering only

mode by pressing the push button and turning the

change lever to the

mark (Fig. 19).

Push button

Change lever

Fig. 19

(1) Mount the bull point or cold chisel.

(2) Press the push button and set the change lever to

middle of

mark and mark (Fig. 20).

The rotation is released, turn the grip and adjust the

cold chisel to desired position (Fig. 21).

Push button

Change lever

Fig. 20

Grip

Fig. 21

(3) Turn the change lever to mark (Fig. 19).

Then bull point or cold chisel is locked.

7. Using depth gauge (Fig. 22)

(1) Loosen the knob on the side handle, and insert the

depth gauge into the mounting hole on the side

handle.

(2) Adjust the depth gauge position according to the

depth of the hole and thighten the knob securely.

Depth gauge

Mounting hole

Side handle

Fig. 22

8. How to use the drill bit (taper shank) and the taper

shank adapter

(1) Mount the taper shank adapter to the rotary hammer

(Fig. 23).

(2) Mount the drill bit (taper shank) to the taper shank

adapter (Fig. 23).

(3) Turn the switch ON, and drill a hole in prescribed

depth.

(4) To remove the drill bit (taper shank), insert the cotter

into the slot of the taper shank adapter and strike the

head of the cotter with a hammer supporting on the

rests (Fig.24).

English

Drill bit

Front cap

Grip

Taper shank adapter

Fig. 23

Cotter

Rest

Taper shank adapter

Fig. 24

OPERATIONAL CAUTIONS

Resting the unit after continuous work

(1) The power tool is equipped with a temperature

protection circuit to protect the motor.

Continuous work may cause the temperature of the

unit to rise, activating the temperature protection

circuit and automatically stopping operation.

If this happens, allow the power tool to cool before

resuming use.

(2) After use for continuous works, rest the unit for

15 minutes or so when replacing the battery. The

temperature of the motor, switch, etc., will rise if

the work is started again immediately after battery

replacement, eventually resulting in burnout.

REACTIVE FORCE CONTROL

This product is equipped with a Reactive Force Control

(RFC) feature that reduces jerking of the tool body.

If the tool bit is suddenly overburdened, any jerking of the

tool body is reduced by activation of the slip clutch or by

stopping of the motor by the sensor built into the tool body.

If the motor is stopped because of overburdening

detection by the controller, this is indicated by blinking

of the remaining battery lamp while the switch is pulled.

(Fig. 25)

Because the RFC feature may not activate or its

performance may be insuﬃ cient depending on the

working environment and conditions, be careful not to

suddenly overburden the tool bit while operating.

●

Possible causes of sudden overburdening

Tool bit biting into material

Impact against nails, metal or other hard objects

Tasks involving prying or any excess application of

pressure, etc.

Also, other causes include any combination of the

aforementioned.

●

When the reactive force control (RFC) is triggered

When the RFC is triggered and the motor stops, turn

oﬀ the tool’s switch and remove the cause of the

overburdening before continuing operation.

Fig. 25

English

MAINTENANCE AND INSPECTION

WARNING

Be sure to turned oﬀ the switch and remove the battery before maintenance and inspection.

1. Inspecting the tool

Since use of as dull tool will degrade eﬃ ciency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Check the Screws

Loose screws are dangerous. Regularly inspect them

and make sure they are tight.

CAUTION

Using this power tool with loosened, screws is

extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. How to replace grease

Low viscosity grease is applied to this rotary hammer

so that it can be used for a long period without

replacing the grease. Please contact the nearest

service center for grease replacement when any

grease is leaking from loosened screw. Further use

of the rotary hammer despite the grease shortage

causes seizure to reduce the service life.

CAUTION

A speciﬁ c grease is used with this machine,

therefore, the normal performance of the machine

may be badly aﬀ ected by use of other grease.

Please be sure to let one of our service agents

undertake replacement of the grease.

5. Cleaning on the outsider

When the power tool is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not

use chloric solvents, gasoline or paint thinner, for they

melt plastics.

6. Cleaning of the battery installation compartment

After drilling concrete, if concrete dust has

accumulated on the terminals or the area where

the battery slides within the battery installation

compartment, clean oﬀ the accumulated concrete

dust with a dry cloth before using the tool. (Fig. 26)

Also, after cleaning, ensure that the battery can be

installed and removed smoothly from the tool.

CAUTION

Using the tool when the battery is covered with

concrete dust may lead to accidents such as the

battery falling during use.

Furthermore, such use may cause a malfunction

or contact failure between the battery and the

terminals.

Terminals

Battery sliding grooves

Fig. 26

7. Disposal of the exhausted battery

WARNING

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The

product that you have purchased contains a

rechargeable battery. The battery is recyclable.

At the end of it´s useful life, under various state

and local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check

with your local solid waste oﬃ cials for details

in your area for recycling options or proper

disposal.

8. Storage

Storing in a place below 104°F (40°C) and out of the

reach of children.

NOTE

Make sure that the battery is fully charged when

stored for a long period (3 months or more). The

battery with smaller capacity may not be able to be

charged when used, if stored for a long period.

NOTE

Storing lithium-ion batteries

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage of batteries with a low charge

may result in performance deterioration, signiﬁ cantly

reducing battery usage time or rendering the batteries

incapable of holding a charge.

English

However, signiﬁ cantly reduced battery usage time

may be recovered by repeatedly charging and using

the batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

9. Service and repairs

All quality power tools will eventually require servicing

or replacement of parts because of wear from normal

use. To assure that only authorized replacement

parts will be used, all service and repairs must be

performed by a HITACHI AUTHORIZED SERVICE

CENTER, ONLY.

10. Service parts list

CAUTION

Repair, modiﬁ cation and inspection of Hitachi

Power Tools must be carried out by a Hitachi

Authorized Service Center.

This Parts List will be helpful if presented with

the tool to the Hitachi Authorized Service Center

when requesting repair or other maintenance. In

the operation and maintenance of power tools,

the safety regulations and standards prescribed

in each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modiﬁ ed to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used

with batteries other than these designated by us, or

when the battery is disassembled and modiﬁ ed (such

as disassembly and replacement of cells or other

internal parts).

La page charge ...

Hitachi DH 18DBL Manuel utilisateur

Marque: Hitachi

Modèle: DH 18DBL

Catégorie: Perceuses électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi DH 18DBL User manual
español: Hitachi DH 18DBL Manual de usuario

Hitachi DH 18DBL Manuel utilisateur

Hitachi DH 18DBL Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents