Samsung MX-FS8000 Manuel utilisateur

Catégorie
Lecteur CD
Taper
Manuel utilisateur
PREMIUM HI-FI Component System
MP3/WMA/CD-DA Playback with CD/USB
user's manual
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
MX-FS8000
MX-FS8000-ZC_ENG_131011.indd 1 2013-10-11 �� 1:27:04
2 English English 3
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous voltage” inside
the product that presents a risk of electric shock or
personal injury.
CAUTION :
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
This symbol indicates important instructions
accompanying the product.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1 LASER product.
Use of controls, adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
DANGER :
• Complies with 21CFR 1040.10 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007
• VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID
DIRECT EXPOSURE TO BEAM. (FDA 21 CFR)
WARNING
• T
o reduce the risk of fire or electric shock, do not expose this
appliance to rain or moisture.
CAUTION
• Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
• The Mains plug is used as a disconnect device and shall stay readily
operable at any time.
• Use only a properly grounded plug and receptacle.
- An improper ground may cause electric shock or equipment
damage. (Class l Equipment only.)
• CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN. AVOID EXPOSURE TO THE BEAM (IEC 60825-1)
• THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE. DO NOT OPEN COVER AND DO
NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
• An administration fee may be charged if either
a. an engineer is called out at your request and there is no defect in the product (i.e. where you have failed to read this user's manual)
b. you bring the unit to a repair centre and there is no defect in the product (i.e. where you have failed to read this user's manual).
• The amount of such administration charge will be advised to you before any work or home visit is carried out.
Important Safety Instructions
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating
instructions handy for future reference.
1) Read these instructions.
2) Keep these Instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachment/accessories
specified by the manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for
long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as when the power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
MX-FS8000-ZC_ENG_131011.indd 2 2013-10-11 �� 1:27:04
2 English English 3
Precautions
• Ensure that the AC power supply in your house complies
with the identification sticker located on the back of your
product.
• Install your product horizontally, on a suitable base (furniture),
with enough space around it for ventilation (7.5~10cm).
• Do not place the product on amplifiers or other equipment
which may become hot. Make sure the ventilation slots are
not covered.
• Do not stack anything on top of the product.
• Before moving the product, ensure the Disc Insert Slot is
empty.
• To turn off the product completely, disconnect the AC plug from
the wall outlet. Disconnect the AC plug from the wall outlet if
you will leave the device unused for a long period of time.
• During thunderstorms, disconnect the AC plug from the wall
outlet. Voltage peaks due to lightning could damage the
product.
• Do not expose the product to direct sunlight or other heat
sources. This could cause the product to overheat and
malfunction.
• Protect the product from moisture, and excess heat or
equipment creating strong magnetic or electric fields (i.e.
speakers.).
• Disconnect the power cable from the AC supply if the
product malfunctions.
• Your product is not intended for industrial use. It is for
personal use only.
• Condensation may occur if your product or disc has been
stored in cold temperatures. If transporting the product
during the winter, wait approximately 2 hours until the
product has reached room temperature before using.
• The batteries used with this product contain chemicals
that are harmful to the environment. Do not dispose of
batteries in the general household trash.
• Maintain an open space of approximately 6 inches (15 cm)
on the sides and rear of the system, for ventilation purposes.
• Place the loudspeakers at a reasonable distance on either
side of the system to ensure good stereo sound.
• Direct the loudspeakers towards the listening area.
Cautions on Handling and Storing Discs
Small scratches on the disc may reduce sound and picture
quality or cause skipping.
Be especially careful not to scratch discs when handling
them.
Holding Discs
• Do not touch the playback side of the disc.
• Hold the disc by the edges so that fingerprints will not get
on the surface.
• Do not stick paper or tape on the disc.
Disc Storage
• Do not keep in direct sunlight.
• Keep in a cool ventilated area.
• Keep in a clean protective jacket.
Store vertically.
• Do not allow the discs to become contaminated with dirt.
• Do not load cracked or scratched discs.
Handling and Storing Discs
If you get fingerprints or dirt on a disc, clean it with a mild
detergent diluted in water and wipe with a soft cloth.
• When cleaning, wipe gently from the inside to the outside of
the disc
• Condensation may form if warm air comes into contact
with cold parts inside the product. When condensation
forms inside the product, it may not operate correctly. If this
occurs, remove the disc and let the product stand for 1 or
2 hours with the power on.
Disc Types And Disc Format
This product does not support Secure (DRM) Media files.
CD-R Discs
• Some CD-R discs may not be playable depending on
the disc recording device (CD-Recorder or PC) and the
condition of the disc.
• Use 650MB/74 minute CD-R discs.
Do not use CD-R discs over 700MB/80 minutes as they
may not be played back.
• Some CD-RW (Rewritable) media may not be playable.
• Only CD-Rs that are properly "closed" can be fully played. If
the session is closed, but the disc is left open, you may not
be able to fully play the disc.
CD-R MP3/WMA Discs
• Only CD-R discs with MP3 files in ISO 9660 or Joliet format
can be played.
• MP3 file names should contain no blank spaces or special
characters (. / = +).
• Use discs recorded with a compression/decompression
data rate greater than 128Kbps.
• Only files with the ".mp3" and ".wma" extensions can be
played.
• Only a consecutively written multisession disc can be
played. If there is a blank segment in the Multisession disc,
the disc can be played only up to the blank segment.
• If the disc is not closed, it will take longer to begin playback
and not all of the recorded files may play.
• For files encoded in Variable Bit Rate (VBR) format, i.e. files
encoded in both low bit rate and high bit rate (e.g., 32Kbps
~ 320Kbps), the sound may skip during playback.
• A maximum of 999 files can be played per CD.
• Supported Audio Formats(Bit Rate):WMA 56~128kbps,
MP3 80~320kbps.
Important Information on Use
MX-FS8000-ZC_ENG_131011.indd 3 2013-10-11 �� 1:27:05
4 English English 5
Safety Warnings ................................................. 2
Important Information on Use ........................... 3
Precautions .................................................... 3
Cautions on Handling and Storing Discs ........ 3
Disc Types And Disc Format .......................... 3
Accessories ........................................................ 4
Description ......................................................... 5
Front Panel .................................................... 5
Rear Panel ..................................................... 6
Remote Control ............................................. 7
Installing Batteries In The Remote
Control .................................................... 7
Connecting the Speakers .............................. 7
Basic Functions ................................................. 8
The Display function....................................... 8
Playing CD ..................................................... 8
Loading Compact Disc ............................ 8
CD/MP3/WMA-CD Playback .................. 8
Selecting a Track ..................................... 9
Searching for a Track/Folder Quickly ....... 9
Searching for a Specific Music Passage
on a CD ................................................... 9
Repeat One or All Tracks on a CD ........... 9
A-B Repeat Playback .............................. 9
CD Programming .................................... 9
Viewing or Editing the Programmed
Track ..................................................... 10
Playing USB Devices ................................... 10
Before you begin! ..................................10
To Select a File from a USB Device........ 10
To Use High Speed Search ................... 10
To Delete a File ...................................... 10
To skip next 10 files ............................... 11
Move FOLDER ...................................... 11
How to safely remove the USB device ......
11
Read Before Using the USB Storage
Devices.................................................. 11
Bluetooth ..................................................... 11
What is Bluetooth? ................................ 11
To connect the Hi-Fi Component to a
Bluetooth device.................................... 11
To disconnect the Bluetooth device from
the Hi-Fi Component ............................. 12
To disconnect the Hi-Fi Component from
the Bluetooth device............................... 12
Using My Karaoke ....................................... 12
10 Skip Function .......................................... 13
Auto Change Function ................................. 13
Listening to the Radio .................................. 13
To Store the Stations You Want ............. 13
Selecting a Stored Station ..................... 13
Advanced Functions ........................................ 14
Timer Function ............................................. 14
Setting the Clock ................................... 14
Setting the Timer ................................... 14
Cancelling the Timer .............................. 15
The Recording Function ...............................15
Basic Recording .................................... 15
Recording Speed ..................................16
Special Sound Effect....................................16
Selecting EQ Mode ............................... 16
Using the FOOTBALL Mode .................. 16
GIGA SOUND Function ......................... 16
BEAT WAVING Function ........................ 17
DJ BEAT Function ................................. 17
Booting Sound Function ........................ 17
Troubleshooting ...............................................18
Specifications ..................................................19
Contents
Thank you for buying this SAMSUNG Hi-Fi Component system.
Please take time to read these instructions.
They will allow you to operate your system with ease and take full advantage of its features.
Contents
Symbols
Important Note
Accessories
Check for the supplied accessories below.
USB CD/
AH59-02553A
User's Manual
Remote Control/ Batteries FM Antenna Power Cable
• Figures and illustrations in this user's manual are provided for reference only and may differ from actual product
appearance.
MX-FS8000-ZC_ENG_131011.indd 4 2013-10-11 �� 1:27:06
4 English English 5
1. Display Panel
2. BACKWARD SEARCH/SKIP button
3. CD/ Bluetooth button
4. DISC slot
5. GIGA SOUND BEAT button
6. TUNER/AUX button
7. FORWARD SEARCH/SKIP button
8. FOLDER- button
9. Eject button for Disc
10. MASTER VOLUME
11. BEAT WAVING button
12. FOLDER+ button
13. POWER button
•Press this button to switch your product on or
off.
14. CHORUS button for DJ BEAT sound effect
15. USB 2 button
16. USB REC button
17. FLANGER button for DJ BEAT sound effect
18. DJ BEAT button
19. WAHWAH button for DJ BEAT sound effect
20. +PANNING button for DJ BEAT sound effect
21. USB 2 jack for Playing and USB Recording
22. PLAY/PAUSE button
23. AUX IN 1 jack
Connecting an external device such as an MP3
player.
• Connect AUX IN 1 on the front panel of the
product to the Audio Out of the external
device/MP3 player.
• Press the TUNER/AUX button to select the
AUX1.
24. MIC jack
25. STOP button
26. USB 1 jack for only Playback
27. REMOTE CONTROL SENSOR
28. DISPLAY/ DEMO button
29. USB 1 button
30. EQ button
31. FOOTBALL MODE button
Front Panel
1 2 3 4 5 6 7 8 9
1110 12
13
14
15
16
171819202122232425
28 27
26
29
31
30
Description
MX-FS8000-ZC_ENG_131011.indd 5 2013-10-11 �� 1:27:07
6 English English 7
Description
1. Cooling fan
• The fan operates while the unit is powered on.
If you set the unit to the minimum volume, the fan
won't operate.
Secure a minimum 10 cm of clear space from all
sides of the fan when installing the product.
2. POWER
• Insert only provided power cable.
3. 2.2 CH Speaker Terminals
1.
To achieve the correct sound quality, when you con-
nect the speakers, match the color of the speaker
plugs to the color of the speaker jacks. See below.
• LEFT channel (marked
L
, White/Purple).
• RIGHT channel (marked
R
, Red/Purple).
• Don't force in the Purple SUBWOOFER connector
into the White or Red speaker jack.
4. LED Terminals for Speaker Beat Waving.
The LED Terminals do not distinguish
between the left and right channel.
5. ONLY FOR SERVICE
• This jack is just for testing, please don't use it.
6. AUX IN 2 Terminals
1.
Use an Audio Cable (not supplied) to connect AUX
IN 2 on the product to Audio Out on the external
analog output device.
• Be sure to match connector colors.
• If the external analog output device has only one
Audio Out jack, connect either left or right.
• Press the TUNER/AUX button to select the AUX 2.
• If no button actions for more than 8 hours in AUX
mode, the power will automatically turn off.
7. FM Antenna Terminals
1.
Connect the FM antenna to the FM antenna con-
nector terminal.
2.
Slowly move the antenna wire until you find a
location where reception is good, then fasten it to
a wall or other rigid surface.
3.
If reception is poor, you may need to install an
outdoor antenna. To do so, connect an outdoor
FM antenna to the FM socket on the rear of the
system using a 75Ω coaxial cable (not supplied).
Rear Panel
542 3 76
1
MX-FS8000-ZC_ENG_131011.indd 6 2013-10-11 �� 1:27:08
6 English English 7
Description
Remote Control
Connecting the Speakers
Recommended speaker setup.
Installing Batteries In The Remote Control
` Place batteries in the remote control so
they match the polarity : (+) to (+) and (–)
to (–).
` Do not dispose of batteries in a fire.
` Do not short circuit, disassemble or
overheat the batteries.
` Danger of explosion if battery is
incorrectly replaced. Replace only with
the same or equivalent type.
` The remote control can be used up to
approximately 23 feet (7 meters) in a straight line from the system.
* Battery size: AAA
1. POWER
2. TUNER/AUX
3. USB
4. Number(0~9)
button
During playback,
press the desired
track number.
The selected
track is played.
5. SKIP(-10, +10)
6. SKIP
7. STOP
8. PLAY
9. REPEAT
10. GIGA
11. ENTER
12. VOLUME (-,+)
13. TUNING MODE
14. TIMER ON/OFF
15. TIMER SET
16. SLEEP
Set a sleep time
to shut off the
product.
17. MY KARAOKE
18.
MIC VOLUME -, +
19. USB REC
20. DELETE
21. Mono/Stereo
for FM, CD REC
SPEED for CD
Ripping
22. TUNING/
ALBUM ,,.
23. EQ
24. AUTO CHANGE
25. REPEAT A-B
26. PAUSE
27. SEARCH
28.
CD/Bluetooth
29. BEAT WAVING
30. MUTE
Turn on/off
the sound
temporarily.
USB CD/
AH59-02553A
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
20
23
22
24
25
26
27
28
29
30
The product may not operate properly if not
installed in accordance with recommended
speaker setup, or exposed to shaking or
external shocks.
Do not stretch the speaker wires or place a
heavy object on them.
MX-FS8000-ZC_ENG_131011.indd 7 2013-10-11 �� 1:27:13
8 English English 9
Basic Functions
The Display function
You can view all functions available on the dis-
play, adjust the brightness of the display and set
the Display/LED either on or off.
Each time you press the DISPLAY/DEMO button,
the display mode will change as follows:
The Dimmer function
The Dimmer function is selected and the display dark-
ens.
LED OFF
The LED is turned off while the dimmer function is work-
ing.
Clock ON
The Clock you set is displayed.
Display/LED ON
All displays and the LED are turned on.
The
DEMO Music function
Press DISPLAY/DEMO button for 5 seconds to oper-
ate the demo mode.
When you press the DISPLAY/DEMO button while
displaying the demo, the function operates as follows:
DIMMER
LED Off (unit/speaker)
--:--
[time dis-
play]
LED On (unit/speaker)
- To cancel the Demo Music mode
• Press the DISPLAY/DEMO button for 5 seconds.
The current mode is canceled and the product is
turned off.
• Press TUNER/AUX, CD/Bluetooth or USB button.
The current mode is canceled and the mode is
changed to the mode you selected.
- While displaying DEMO Music, only the
[Power],
VOL,
[MUTE] buttons and the buttons mentioned
above work.
- If you connect speaker to AUX1 while displaying
DEMO, sound is produced through AUX1 and you
can use the VOL buttons and
[MUTE].
Playing CD
Loading Compact Disc
You can play 12 cm compact disc that requires no
adapter.
1. Insert a disc gently into the disc slot with the disc's
label facing up. The disc will be played automatically.
• You can load or unload compact discs when the
radio, USB or auxiliary source function is selected.
When you press the EJECT button, all of the other
functions will change to the CD mode.
• If no buttons are pressed on the product or remote
control for more than 3 minutes when the product is
in Pause mode, it will change to Stop mode.
• If no buttons are pressed on the product or remote
control for more than 25 minutes when the product
is in Stop mode, the product will turn off.
CD/MP3/WMA-CD Playback
This product is designed to play the following audio
disc types: CD, CD-R, CD-RW, MP3/WMA-CD.
1. Insert a disc gently into the disc slot with the disc's
label facing up.
2. The disc will be played automatically.
• For MP3/WMA-CD audio, it may take several minutes
for the product to finish scanning the disc tracks.
• If you play a file with an English name or a MP3/
WMA-CD file an English title, the song title will be
shown in the display. (Titles in other languages will not
be displayed.)
• An English-titled track containing a special character
will not be displayed.
<CD Playback Display>
Track Indicator
Playtime Indicator
3. Adjust the volume according to needs with the
following procedures.
• Turn the VOLUME control on the product.
• Press the VOL+ or VOL- button of the remote control.
The volume level can be adjust in 31 steps(VOLUME
MIN, VOLUME01 ~ VOLUME 29, and VOLUME MAX).
4. Main Unit
To pause playback temporarily, press the p button.
Press p again to continue playing the disc.
Remote control
To pause playback temporarily, press the PAUSE(#) but
-
ton.
Press the PLAY(+) button to continue playing the disc.
5. To end playing, press the STOP (
@
) button.
• If no CD is in the disc slot, “NO DISC” appears on the
display.
• The quality of MP3/WMA-CD playback may vary
depending on the condition of the disc or the condition of
the recorder with which the disc was created.
• If a disc contains different types of files or unnecessary
folders, you will have problems with playback.
Gently insert a CD into the disc slot. Do not apply
excessive force.
• Do not apply force to the product or place a heavy
object on the product.
• Do not insert an out-of-spec or oddly shaped CD
(heart shaped, octangular, etc.). You can damage the
product.
• Carefully maintain your CDs.
MX-FS8000-ZC_ENG_131011.indd 8 2013-10-11 �� 1:27:14
8 English English 9
Basic Functions
Selecting a Track
You can select a desired track while the disc is
being played
.
To play the previous track
Press the
[
button within 3 seconds after the current
track has started playing.
Press the
[
button twice at least 3 seconds after the
current track has started playing.
To play the next track
Press the
]
button.
To play the current track from the beginning
Press the
[
button 3 seconds after the current track
started playing.
To play the track of your choice
Press the
[
or
]
button to move to a desired track.
• You can also
use the
number(0~9)
button on the
remote control to select a track.
Searching for a Track/Folder Quickly
You can select a track/folder directly without
the
[
,
]
button.
CDDA/MP3-CD/WMA-CD
1. When searching is done, the track will automatically
start playing.
Searching for a Specific Music Passage on
a CD
When listening to a CD, you can quickly search
for a specific music passage on a track.
Forward Search ............................
)
Backward Search
.........................
(
You can also press and hold the
[
,
]
buttons on
the product to automatically scan for a track.
Repeat One or All Tracks on a CD
You can repeat playing CD unlimitedly:
• CD containing a specific track.
• Whole tracks of a CD.
1. Press the REPEAT button on the remote
control.
Each time you press the REPEAT button, the
repeat mode will change as follows:
MP3:
OFF TRACK DIR ALL RANDOM
CD:
OFF TRACK ALL RANDOM
2. When you want to stop the repeat function,
press the REPEAT button until "OFF" is
displayed.
• OFF: Cancels repeat playback.
• TRACK: Rpeatedly plays the selected track.
• DIR(DIRECTORY): Repeatedly plays all tracks in
the selected folder.
• ALL: Repeatedly plays the entire disc.
• RANDOM: Plays tracks in random order.
A-B Repeat Playback
You can repeatedly play back a designated section
of a CD.
1. Press the REPEAT A-B button at the beginning
of desired part.
• 'RPT A' will be displayed.
2. Press the REPEAT A-B button at the ending of
desired part.
• 'RPT AB' will be displayed.
3. To cancel REPEAT A-B function, press the
REPEAT A-B button again.
• 'OFF' will be displayed.
The REPEAT A-B function is available within a
track.
CD Programming
This function is not available during playback of an
MP3/WMA-CD.
• You can program the playback order of up to 24
tracks of your choice.
• However, you must stop playing the CD before
selecting tracks.
1. While in CD playback mode, press the
STOP(
@
) button to stop playing the CD.
2. Press the ENTER
( )
button to display the
message below:
(01= program number, ---= track number)
MX-FS8000-ZC_ENG_131011.indd 9 2013-10-11 �� 1:27:15
10 English English 11
Basic Functions
3. Use the
[
or
]
button to move to a desired
track.
• Press
[
to move to the previous track.
• Press
]
to move to the next track.
4. Press the ENTER
( )
button to confirm your
selection, the selection is stored and
is displayed.
5. To select another track, follow Steps 3 and 4
above.
6. Press the
PLAY (+) button
to play the
programmed tracks.
7. Press the STOP (
@
) button to stop playing the
programmed tracks, Press the STOP (
@
) button
again to cancel playing the programmed tracks.
• If you eject the disc or turn off the product
or change other function mode,
your
programming will be canceled.
Viewing or Editing the Programmed
Track
You can view a list of programmed tracks and
edit them as you want.
1. If a programmed track is being played, press
the STOP (
@
) button once.
2. Press the ENTER
( )
button twice to display
the message below:
(01= program number, 002= track number)
3. Repeatedly press the ENTER
( )
button until
the desired track is displayed.
4. Press the
[
or
]
button to select a different
track.
5. Press the ENTER
( )
button to confirm your
selection.
6. To play the programmed tracks, press the Play
(
+
) button.
Playing USB Devices
Connect an external storage device such as a USB
flash memory or external HDD (Hard Disk Drive)
to the product. You can play files in MP3/WMA
format.
Before you begin!
1. Connect the external USB storage device to your
product.
2. Select the USB mode by pressing the USB 1 or USB 2
button on the product or the USB button on the remote
control.
3. The first file of the first directory plays automatically
.
4. To stop playing
Press the STOP (
@
) button to stop playing.
To remove the USB device
If you press the STOP (
@
) button once
again, you can remove the USB device safe-
ly.
Do not connect a USB recharger to the USB
port of this product. You can damage the
product.
To Select a File from a USB Device
You can select an MP3 file while the product is
playing.
If you want to move the previous/next track, press the
[,] buttons briefly.
• The unit moves the previous/next file within the
directory.
• If you press the
[,] buttons more times than the
number of the files in the directory, the unit moves to
the next directory.
To repeat
1. Press the REPEAT button.
Each time you press the REPEAT button, the repeat
mode will change as follows:
OFF TRACK DIR ALL RANDOM
2. When you want to stop the repeat function, press the
REPEAT button until "OFF" is displayed.
• OFF: Cancels repeat playback.
• TRACK: Repeatedly plays the selected file.
• DIR(DIRECTORY): Repeatedly plays all files in the
selected folder.
• ALL: Repeatedly plays all files.
• RANDOM: Plays files in random order.
To Use High Speed Search
You can search the desired section quickly while
the product is playing.
1. Press the
(
,
)
button.
• Each time you press the button, you will move
forward/backward fast.
Sound does not output during a high speed search.
To Delete a File
You can delete a file from your USB device.
1.
Select a file you want to delete.
2.
Press the DELETE button on the remote control.
3.
Press [,] buttons on the product or remote control
to select YES/NO.
MX-FS8000-ZC_ENG_131011.indd 10 2013-10-11 �� 1:27:16
10 English English 11
Basic Functions
4.
Press the ENTER button on the remote control.
The selected file will be deleted.
The NTFS file system is not supported.
To skip next 10 files
1. Press the +10 or -10 button while in playback mode.
The unit will skip as many as 10 tracks forward or 10
tracks back from the current track.
Move FOLDER
Press the remote control's TUNING/ALBUM
,
,
.
button
or the product's FOLDER -, + button to move to the
previous/ next folder.
How to safely remove the USB device
1. Press the (
@
) button twice while the USB is playing or
press the
(
@
) button once when play is stopped.
2. When the REMOVE message appears on the display,
remove the USB device.
Read Before Using the USB Storage
Devices
• Some USB devices may not work properly with this
product.
• This product only supports external HDD`s that are
formatted in FAT file system.
• USB 2.0 HDDs should be connected to a separate power
source. Otherwise, the USB 2.0 HDDs will not work.
• If multiple USB external storage are connected together,
only the MP3 files in the first HDD will be played.
• Files with DRM are not supported. Digital Right
Management(DRM) restricts unauthorized access to a DRM
file so that the copyright of the file is protected from piracy.
• Even if a file has an .mp3 extension, the file cannot be
played if it is formatted in MPEG layer 1 or 2.
• Do not use an unrecognized USB hub.
• Only the first 15 characters of a MP3/WMA file are
displayed.
• Only removable HDDs with less than 160GB are
supported. Depending on the device, a 160GB- or more
removable HDD may not be supported.
• It can take several minutes for the product to recognize
the files on some USB devices.
• Some USB devices (USB HDDs, in particular) may cause
a delay when moving from track to track.
• With USB storage devices supporting USB VER1.1 only,
the product may access files slowly or may not recognize
the file properties.
• The maximum electrical current supported by an external
USB devices via each USB port is 0.5A (based on DC 5V).
• If there is no USB connection or STOP mode lasts for more
than 25 minutes, the product will automatically turn off.
• A certain USB, digital camera device, USB card reader,
iPod, iPhone or Smart Phone may not be supported.
Bluetooth
You can use a Bluetooth device to enjoy music with
high quality stereo sound, all without wires!
What is Bluetooth?
Bluetooth is a technology that enables Bluetooth
compliant devices to interconnect easily with each
other using a short wireless connection.
• A Bluetooth device may cause noise or malfunction,
depending on usage, when:
- A part of your body is in contact with the receiving/
transmitting system of the Bluetooth device or the Hi-Fi
Component.
- It is subject to electrical variation from obstructions
caused by a wall, corner, or office partitioning.
- It is exposed to electrical interference from same
frequency-band devices including medical equipment,
microwave ovens, and wireless LANs.
• Pair the Hi-Fi Component with the Bluetooth device while
they are close together.
• The greater the distance between the Hi-Fi Component and
the Bluetooth device, the worse the quality. If the distance
exceeds the Bluetooth operational range, the connection is
lost.
• In poor reception-sensitivity areas, the Bluetooth connection
may not work properly.
• The Bluetooth connection only works when it is close to
the set. The connection will be automatically cut off if the
Bluetooth device is out of range. Even within range the
sound quality may be degraded by obstacles such as walls
or doors.
• This wireless device may cause electric interference during
its operation.
To connect the Hi-Fi Component to a
Bluetooth device
Before you begin, confirm that your Bluetooth
device supports the Bluetooth-compliant stereo
headset function.
1.
Press the CD/ Bluetooth button of the Hi-Fi Component
to display the BLUETOOTH message.
• You will see WAIT for a while and then READY on the
front display of the Hi-Fi Component.
2.
Select the Bluetooth menu on the Bluetooth device you
want to connect. (Refer to the Bluetooth device's user
manual.)
3.
Select the Stereo headset menu on the Bluetooth device.
• You will see a list of scanned devices.
4.
Select "[Samsung] HI-FI XXXXXX" from the list.
• When the product is connected to the Bluetooth
device, it will display CONNECTED
BLUETOOTH
on the front display.
MX-FS8000-ZC_ENG_131011.indd 11 2013-10-11 �� 1:27:16
12 English English 13
Basic Functions
• If the Bluetooth device has failed pair with the product,
delete the previous “[Samsung] HI-FI XXXXXX” found by
the Bluetooth device and have it search for the product
again.
5.
Play music on the connected device.
• You can listen to the music playing on the connected
Bluetooth device over the Hi-Fi Component system.
• In
Bluetooth
mode, some model's Play/Repeat/Stop/
Next/Back functions are not available.
The product only supports Middle Quality SBC data (up
to 237kbps@48kHz), and does not support High Quality
SBC data ([email protected]).
• The AVRCP feature is not supported.
• Connect only to a Bluetooth device that supports the
A2DP (AV) function.
• You cannot connect to a Bluetooth device that
supports only the HF (Hands Free) function.
• Only one Bluetooth device can be paired at a time.
• Once you have turned off Hi-Fi Component and the
pairing is disconnected, the pairing will not be restored
automatically. To reconnect, you must pair the device
again.
• The Hi-Fi Component system may not search or
connect properly in the following cases:
- If there is a strong electrical field around Hi-Fi
Component.
- If several Bluetooth devices are simultaneously paired
with Hi-Fi Component.
- If the Bluetooth device is turned off, not in place, or
malfunctions.
- Note that such devices as microwave ovens, wireless
LAN adaptors, fluorescent lights, and gas stoves use
the same frequency range as the Bluetooth device,
which can cause electric interference.
To disconnect the Bluetooth device from
the Hi-Fi Component
You can disconnect the Bluetooth device from Hi-
Fi Component. For instructions, see the Bluetooth
device's user manual.
• The Hi-Fi Component will be disconnected.
• When the Hi-Fi Component is disconnected from the
Bluetooth device, the Hi-Fi Component will display
DISCONNECTED
READY on the its display.
To disconnect the Hi-Fi Component
from the Bluetooth device
Press the CD/Bluetooth button on the front panel
of the Hi-Fi Component to switch from Bluetooth
mode to another mode or turn off the Hi-Fi Compo-
nent.
• The connected Bluetooth device will wait a certain amount
of time for a response from the Hi-Fi Component before
terminating the connection.(Disconnection time may differ,
depending on the Bluetooth device)
• The currently connected device will be disconnected.
In Bluetooth connection mode, the Bluetooth connection
will be lost if the distance between the Hi-Fi Component
and the Bluetooth device exceeds 16.25 feet (5 meters).
• If the Bluetooth device comes back into the effective
range after disconnecting, you can restart the Hi-Fi
Component to restore the pairing with the Bluetooth
device.
• The Hi-Fi Component automatically turns off after 25
minutes in the Ready mode.
Using My Karaoke
You can use the MY Karaoke function to sing
along with your favorite CDs and USB tracks.
1. Connect the microphone to the MIC jack on the front
of the product.
` If your microphone plug is larger than the 3.5 mm
MIC jack, you need a Connector-Adaptor (not
supplied) to complete the connection.
- First, connect the Connector-Adaptor to the MIC jack
on the front of the product,
- Second, connect the microphone (with larger jack) to
the Connector-Adaptor.
2. Press the MIC VOL-, + button on the remote
control to adjust the volume of the microphone.
3. Press the
MY KARAOKE
button on the remote
control
to suppress the vocal if you need. Each time
the button is pressed, the selection is changed as
follows:
MY KARAOKE ON
MY KARAOKE OFF
` If you hear strange noises (squealing or howling)
while using the Karaoke feature, move the
microphone away from the speakers. Turning down
the microphone's volume or the speaker volume is
also effective. Do not set the MICROPHONE towards
the SPEAKER.
` The microphone does not operate in the AUX and
TUNER mode.
` If you connect a microphone, GIGA SOUND
automatically turns off. To turn Giga Sound back
on you must remove the microphone, and then
press the Giga Sound button.
MX-FS8000-ZC_ENG_131011.indd 12 2013-10-11 �� 1:27:16
12 English English 13
Basic Functions
Listening to the Radio
To Store the Stations You Want
You can store up to:
15 FM stations.
1. Select FM by pressing the TUNER/AUX button.
2. To search for a station, press the TUNNING MODE
button on the remote control or the STOP button on
the product one or more times until MANUAL is
displayed.
• Preset
: Once or more times until PRESET is
displayed. You can search the stored
frequencies in the preset mode.
• Manual : Once or more times until MANUAL is
displayed. You can search the frequencies
one by one in the Manual mode.
3. Select a station by:
• Pressing the TUNING/ALBUM
,
or
.
button on
the remote control to find a station.
4. Press the MO/ST button to switch between stereo and
mono.
• In a poor reception area, select MONO for a
clear, interference-free broadcast.
• This applies only when listening to an FM station.
5. If you do not want to store the radio station found, go
back to Step 3 and search for another station.
Otherwise:
a. Press the ENTER button.
b. Or, press the TUNING/ALBUM button on the
remote control to select a program number.
c. Press the ENTER button to save the preset.
6. To store other radio frequencies, repeat Steps 3, 4 and
5.
Selecting a Stored Station
To listen to a stored station, follow these steps:
1. Select FM by pressing the TUNER/AUX button on
the product or remote control.
2. Press the TUNING MODE button on the remote
control until “PRESET” is displayed.
3. Pres
s [,] button on the main unit or TUNING/
ALBUM , , .
on the remote control to select a
preset number.
` When My Karaoke is on, EQ/GIGA SOUND and
FOOTBALL MODE does not work.
` After the stop operation, the setting of my karaoke
will disappear.
` Only when connected with a Microphone, the my
karaoke function is available.
10 Skip Function
Press the +10 or -10 button while the unit is in
playback mode. The unit will skip as many as 10
tracks forward or 10 tracks back from the current
track.
Auto Change Function
You can circularly play between the disc and the
USB.
1. Press the AUTO CHANGE button on the remote.
Each time press this button, the mode will switch
as following:
AUTO CHANGE OFF
;
AUTO CHANGE ON
• When the AUTO CHANGE mode is "ON",
- the music will be played on DISC
USB1
USB2 continuously.
- if you press the POWER button, function change
button or the EJECT button, the AUTO CHANGE
function automatically switches to "OFF" mode.
- the recording can't work.
- the REPEAT, SLEEP function can't work and
automatically changes to OFF.
- the CD REC SPEED, USB REC, NUMBER KEY
and DELETE function can't work.
• When USB is playing, if you disconnected the USB,
the AUTO CHANGE function automatically switches
to "OFF" mode.
• If there's no USB1, it will jump to USB2.
MX-FS8000-ZC_ENG_131011.indd 13 2013-10-11 �� 1:27:16
14 English English 15
Advanced Functions
Timer Function
Setting the Clock
For each step, you have a few seconds to set the
required options. If you exceed this time, you must
start again.
1. Press the TIMER SET button on the remote
control twice. "CLOCK SET" is displayed.
2. Press the ENTER (
) button on the remote
control. The hour flashes.
• Increase the hours:
TUNING/ALBUM
,
• Decrease the hours:
TUNING/ALBUM
.
3. When the correct hour is displayed, press the
ENTER (
) button, and then the minutes flash.
• Increase the minutes:
TUNING/ALBUM
,
• Decrease the minutes:
TUNING/ALBUM
.
4. When the correct minute is displayed, press the
ENTER (
) button, and then "TIMER PLAY
SET" appears in the display.
Setting the Timer
The timer enables you to switch the product on or
off at specific times automatically.
• Before setting the timer, check that the current time
is correct.
• For each step, you have a few seconds to set the
required options. If you exceed this time, you must
start again.
• If you no longer want the product to be switched
on or off automatically, you must cancel the timer
by pressing the TIMER ON/OFF button.
Example: You want to wake up to music every morn-
ing.
1. Press the TIMER SET button until TIMER PLAY SET is
displayed.
2. Press the ENTER ( ) button.
Result: ON TIME is displayed for a few seconds. You
can set the timer switch-on time.
3. Set the timer switch-on time.
a Press the TUNING/ALBUM , or . button to
set the hours.
b Press the ENTER (
) button.
Result: The minutes flash.
c Press the TUNING/ALBUM , or . button to
set the minutes.
d Press the ENTER ( ) button.
Result: OFF TIME is displayed for a few seconds.
You can now set the timer switch-off time.
4. Set the timer switch-off time.
a Press the TUNING/ALBUM , or . button to
set the hours.
b Press the ENTER (
) button.
Result: The minutes flash.
c Press the TUNING/ALBUM , or . button to set
the minutes.
d Press the ENTER (
) button.
Result: VOLUME XX is displayed, where XX corre-
sponds to the volume already set.
5. Press the TUNING/ALBUM , or . button to adjust the
volume level and press the ENTER ( ) button.
Result: The source to be selected is displayed.
6. Press the TUNING/ALBUM , or . button to select the
source the Hi-Fi Component will play when it switches
on.
If you select... You must also...
FM (radio) ................... a Press the ENTER ( )
button.
b Select a preset station by
pressing the TUNING/
ALBUM , or . button.
CD (compact disc) .....Load a compact disc.
USB ............................Connect the USB device.
7. Press
the ENTER ( ) button.
Result: TIMER REC SET (Do you want to record?) is
displayed.
8. Press
the ENTER ( ) button.
Result: REC SET YES/NO is displayed. You can press
the TUNING/ALBUM , or . button to select
REC YES or REC NO, and then press
ENTER button.
1)
If you select REC NO, it will cancel tuner timer
recording even if you have already set the tuner timer
recording.
2)
If you select REC YES, you can set the tuner timer
recording on and off times.
a.
Press the ENTER (
) button.
Result: ON TIME is displayed for a few seconds.
You can set the tuner timer recording switch-
on time.
b.
Press the ENTER (
) button.
Result: OFF TIME is displayed for a few seconds.
You can set the tuner timer recording switch-
off time.
MX-FS8000-ZC_ENG_131011.indd 14 2013-10-11 �� 1:27:16
14 English English 15
Advanced Functions
• The maximum length of time for tuner timer recording is
5 hours.
• If the timer switch on and off times are identical, the
word ERROR is displayed.
• You can use the
[
,
]
buttons on the product
instead of the TUNING/ALBUM
,
or
.
button to
make adjustments in Steps 3 through 8.
• If the switch-on or -off time is the same as the timer
recording time, only the switch-on or -off time is
effective, and the timer recording is not applied.
• When you use the auto timer, you may need an
additional step to use a CD or USB device with it,
depending on the disc (or device). Consequently, it is
easier to use the tuner instead.
• If you select CD or USB mode when there is no disc or
no USB in the product, it will automatically change to
TUNER.
Cancelling the Timer
After having set the timer, it will start automatically
as shown by the TIMER ON message on the display.
If you no longer want to use the timer, you must can
-
cel it.
To cancel the timer, Press the TIMER ON/OFF button
once.
To restart the timer, Press the TIMER ON/OFF button
once again.
• When
you select the TIMER OFF mode, the TIMER
RECORDING and TIME function are not available.
The Recording Function
Basic Recording
You can record from a CD, a USB device, a radio
broadcast, or an external source to a USB storage
device.
1. Connect the external USB storage device to a USB
( ) jack on your product.
2. Play a disc or USB, turn on the radio and select a
station, or connect the external source to your
product as described below.
CD
• Press
the CD button on the product to select the CD
function.
• Insert
a CD gently into the disc slot.
• Use t
he CD selection (
[
or
]
) buttons to select the
desired song.
TUNER
• Select FM by pressing the TUNER/AUX button.
• Select the radio frequency you want to record.
USB 1
• Connect the USB device with the files you want to
record to USB 1 jack.
• Pres
s the USB button to select USB 1.
• Pla
y a song from the USB 1.
External Source
• Conn
ect an External device/MP3 player to the
product.
• Pres
s the TUNER/AUX button to select <AUX IN 1 or
AUX IN 2>.
• Pla
y a song from the external device.
3.
Press the USB REC button on the remote control to
start recording.
CD
• Track recording message is displayed and CD
recording starts.
• If you want to record all the tracks on the disc,
press and hold the USB REC button. Then, Full CD
recording message will be displayed.
RADIO
• Tuner recording message is displayed and recording
starts.
CD-ROM/ USB
• “FILE COPY” is displayed and recording starts.
• You can also copy a folder including MP3/WMA files
to USB 2 device. if you press and hold the USB REC
button while the system play an MP3 or WMA file in
the folder, your system may show "FOLDER COPY".
• If you play the MP3 or WMA file, the file will be copied
into the USB device. Your system may show "FILE
COPY".
When the recording is done, “STOP” will be displayed.
• If there is the same file name when you copy, "EXIST
FILE" is displayed, and the function is canceled.
• When a microphone is connected to the product if
you press the USB REC button, it activates the MP3
Recording not Copy function.
• When shortly pressing a USB REC button, the file
copy starts and when shortly pressing a USB REC
button for seconds, the folder copy starts.
External Source
• AUX recording message is displayed and recording
starts.
CD/USB1(MP3) & MIC
• MP3 recording message is displayed and recording
starts.
4. To stop recording, press the STOP (@) button. The
recording is automatically saved as an MP3 file.
5. After the recording is finished, a directory named
“RECORDING”(CD-DA), “CD COPY”(CD-ROM/
USB(WMA/MP3)), “TUNER RECORDING”, “AUX
RECORDING” or “MP3 RECORDING” is created in
your device.
MX-FS8000-ZC_ENG_131011.indd 15 2013-10-11 �� 1:27:17
16 English English 17
Advanced Functions
• The WMA/MP2 file just can be copied not recorded.
• Do not disconnect the USB device or the AC Cord during
recording. You can cause file damage.
• If you disconnected the USB device during recording,
the product will turn off and you will not be able to delete
the file that has been recorded. If his occurs, connect the
USB device to a PC, back up the USB data to the PC,
and then reformat the USB device.
• If the USB device does not have enough memory, “NOT
ENOUGH MEMORY” will appear on the display.
• The Recording function supports the FAT file systems
only. The NTFS file system is not supported.
• When you use the CD high speed search function, the
CD recording function is unavailable.
• With some USB devices, recording time may be longer.
• In the Program mode, you can't use the CD recording
function.
• When the Recording function is active, the EQ and
GIGA SOUND functions automatically turn off and are
unavailable.
• During a CD recording, the REPEAT function automatically
turns off and is unavailable.
• If you use the MIC function during a CD recording, the
voice from the microphone will be recorded.
• You can not record audio from the radio when searching
for a station or if there are no frequencies available when
the product is set to Tuner mode.
• Note that setting the input level too loud when recording
music from an external device through the AUX or USB
channel may introduce noise into the recording. If this
case, lower the external device’s volume level.
Recording Speed
Each time you press the CD REC SPEED button
on the remote control, the recording speed will
change as following:
RECORD SPEED x 1
;
RECORD SPEED x 4
• While the
tuner or external source is recording, the recording
speed does not supported.
• Whe
n you select RECORD SPEED x 4, the audio sound
will not be output.
• If you connected the microphone, you just have one recording
speed mode: RECORD SPEED x 1.
• During recording, if you disconnect the microphone, the
recording will stop, even if you reconnect the microphone, it
will still stop.
Special Sound Effect
Selecting EQ Mode
Your Hi-Fi Component system provides predefined
equalizer settings that are optimized for particular
music genre. You can also adjust the bass, middle
and treble levels manually.
1. Press the EQ button.
Each time you press this button, the sound mode will
switch as follows:
OFF
;
FLAT
;
RANCHERA
;
SAMBA
;
CUMBIA
;
HABANERA
;
BOOMBA
;
REGGAE
;
MERENGUE
;
SALSA
;
PARTY
;
POP
;
HIP HOP
;
ROCK
;
JAZZ
;
CLASSIC
;
ELECTRONIC
;
MP3 ENHANCER
;
VIRTUAL SOUND
;
USER EQ
2. To set the BASS, MID (Middle) and TREB (Treble)
levels manually, select USER EQ, and then press
the ENTER button.
Result: The BASS level (left numeric) flashes.
Press the TUNING/ALBUM
, or .
button to
select a level from -06 to 06.
Then, press the ENTER button.
Result: The MIDDLE level (middle numeric) flashes.
Press the TUNING/ALBUM
, or .
button to
select a level from -06 to 06.
Then, press the ENTER button.
Result: The TREBLE level (right numeric) flashes.
Press the TUNING/ALBUM
, or .
button to
select a level from -06 to 06.
Then, press the ENTER button.
Result: Setting is complete.
• When the Hi-Fi Component is recording, the EQ function is
turned off automatically and is unavailable.
• If no buttons are pressed within 8 seconds, your settings will
automatically be cancelled and the previous settings will be
saved.
• The EQ mode may be different depending on your region.
Using the FOOTBALL Mode
The football mode brings greater realism to sports
broadcasts.
1. Press the FOOTBALL MODE button on the product.
Each time you press the button, the sound mode will
switches as follows:
FOOTBALL OFF
;
FOOTBALL MODE 1
;
FOOTBALL MODE 2
• The FOOTBALL mode may be different depending on your
region.
GIGA SOUND Function
The GIGA SOUND function amplifies the bass
sound and provides twice the bass for powerful,
realistic sound.
1. Press the GIGA SOUND BEAT button on the main
unit or the GIGA button on the remote control.
Each time you press the button, the sound mode
switches as follows:
GIGA SOUND BEAT
;
GIGA SOUND OFF
2. To cancel this function, press the GIGA SOUND
BEAT button until the “OFF” is displayed.
• The GIGA SOUND mode may be different depending
on your region.
MX-FS8000-ZC_ENG_131011.indd 16 2013-10-11 �� 1:27:18
16 English English 17
Advanced Functions
BEAT WAVING Function
The Beat Waving function lets you change the
Speaker LED display mode.
1. Each time you press the BEAT WAVING button on
the product, the Speaker LED display mode
changes as follows
:
PARTY 1
;
PARTY 2
;
FUN 1
;
FUN 2
;
PURE
;
FRESH
;
LOVE
;
JOY
;
SUNSET
;
SUNRISE
;
NATURE 1
;
NATURE 2
;
WAVE 1
;
WAVE 2
;
AURORA
;
OFF
• If you
select the BEAT WAVING OFF, all of the speaker
LED displays are turned off.
DJ BEAT Function
The DJ Beat function lets you turn on the
FLANGER, PANNING, CHORUS, and WAHWAH
sound effect functions. The level of each effect is
adjustable.
The set scope is [-15 ~ +15] and the initial set up
value are all 0.
FLANGER : Creates a vibration similar to the sound of a jet
engine revving up and down.
PANNING : Increases the left and right speaker's output in
turn and makes it seem as if the sound is moving
from side to side.
WAHWAH : Creates a 'Wah~ Wah~’ effect.
CHORUS : Creates a vibration that sounds like a singing
chorus.
1. To set the desired effect, press the FLANGER,
PANNING, CHORUS, or WAHWAH button on the
product.
• The red LED turns on around the button you pushed
and around the DJ BEAT button.
• You can control the intensity of the effect with the
Volume Jog. To control the volume, press the product's
DJ BEAT button.
• To cancel an effect, press the effect's button again.
• To change to a different effect, press another effect
button.
• You can apply the PANNING effect to the FLANGER,
CHORUS, or WAHWAH effects.
• To apply the PANNING effect to another effect, press
the PANNING button when the other effect is active or
press another effect button when the PANNING effect
is active.
• Use the Volume JOG to control the intensity of the
effect that was activated last. For example, if you
activated the WahWah effect and then the Panning
effect, the Volume Jog will control the Panning effect.
• To control the intensity of the effect you applied first,
press the button of effect that you applied last to turn
it off. Then, you can use the Volume Jog to control the
intensity of the first effect.
Booting Sound Function
When the Booting Sound Function is on, your Hi-fi
Component demonstrates it's audio prowess as it
boots up.
1. Press the product's GIGA SOUND BEAT button or
the remote control's GIGA button for ten seconds.
The BOOTING SOUND menu appears on the
display panel.
2. Press the product's GIGA SOUND BEAT button or
the remote control's GIGA button for a ten
seconds to turn the BOOTING SOUND function
On or Off.
MX-FS8000-ZC_ENG_131011.indd 17 2013-10-11 �� 1:27:18
English 19
18 English
Troubleshooting
Refer to the chart below when this product does not function properly. If the problem you are
experiencing is not listed below or if the instruction below does not help, turn off the product,
disconnect the power cord, and contact the nearest authorized dealer or Samsung Electronics Service
Center.
Symptom Check/Remedy
I cannot eject the disc. •Isthepowercordpluggedsecurelyintotheoutlet?
•Turnoffthepowerandthenturnitbackon.
Playback does not start
immediately when the
Play/Pause button is pressed.
•Areyouusingadeformeddiscoradiscwithscratchesonthesurface?
•Wipethediscclean.
Sound is not produced. •Nosoundisheardduringfastplayback,slowplayback,andstep
motion playback.
•Arethespeakersconnectedproperly?Isthespeakersetupcorrectly
customized?
•Isthediscseverelydamaged?
The remote control does not
work.
•Istheremotecontrolbeingoperatedwithinitsoperationalangleand
distance range?
•Arethebatteriesdrained?
•Theproductisnotworking.
(Example: The power goes out or
the front panel key doesn't work
or ou hear a strange noise.)
•Theproductisnotworking
normally.
•Runtheresetfunction.Withthe“NODISC”messageonthedisplayof
the product and no disc in the disc slot, press and hold the
STOP (@)
button on the product for more than 5 seconds.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
Can't receive radio broadcast. •Istheantennaconnectedproperly?
•Iftheantenna'sinputsignalisweak,installanexternalFMantennainan
area with good reception.
Turn off automatically after
displaying "PROTECT"
•Checkthepowerinuseiswithintherangeofthepowerwhichspecified
on the rear label of the product.
•If"VoltageSelector"isontherearpanel,checkthepowerissamewith
the voltage that you set manually.
Troubleshooting
MX-FS8000-ZC_ENG_131011.indd 18 2013-10-11 �� 1:27:18
English 19
18 English
Specifications
General
Weight
Main unit
6.1 Kg (13.4 pounds, 215.17 ounces)
Speaker
55 Kg (121.3 pounds, 1940.07 ounces)
Dimensions
Main unit
21.7 in. x 8.4 in. x 14.4 in. (550 (W) x 212 (H) x 367 (D) mm)
Speaker
25.5 in. x 25.7 in. x 17.3 in. (648 (W) x 652 (H) x 440 (D) mm)
Operating Temperature Range
41° ~ 95° F (+5°C~+35°C)
Operating Humidity Range
10 % to 75 %
FM Tuner
Signal/Noise ratio
55 dB
Usable sensitivity
10 dB
Total harmonic distortion
1 %
CD Disc CD : 12 cm (COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Amplifier
Front speaker output
575W/CH (4Ω)
Subwoofer output
575W/CH (4Ω)
Frequency range
22Hz~20KHz
S/N Ratio 65 dB
Channel separation 60 dB
Input sensitivity 800mV (AUX)
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
Specifications
MX-FS8000-ZC_ENG_131011.indd 19 2013-10-11 �� 1:27:18
LIMITED WARRANTY TO ORIGINAL PURCHASER
Samsung Electronics Canada Inc.(SECA), warrants that this product is free from defective
material and workmanship.
SECA further warrants that if this product falls to operate properly within the specified warranty
period and the failure is due to improper workmanship or defective materials, SECA will repair
or replace the product at its option.
All warranty repairs must be performed by a SECA Authorized Service Center. (The name and
address of the location nearest you can be obtained by calling toll free: 1- 800- SAMSUNG)
On carry-in models, transportation to and from the service center is the customer’s responsibility.
The original dated sales receipt must be retained by the customer and is the only acceptable
proof of purchase. It must be presented to the authorized service center at the time service is
requested.
This warranty does not cover damage due to accident, fire, flood and/ or other acts of God; misuse,
incorrect line voltage, improper installation, improper or unauthorized repairs, commercial use or
damage that occurs in shipping. Exterior and interior finish, lamps, glass are not covered under this
warranty. Customer adjustments which are explained in the instruction manual are not covered
under the terms of this warranty. This warranty will automatically be voided for any unit found with a
missing or altered serial number. This warranty is valid only on products purchased and used in
Canada.
HEADQUARTERS
SAMSUNG ELECTRONICS CANADA INC.,
CUSTOMER SERVICE
55 STANDISH COURT MISSISSAUGA, ONTARIO L5R 4B2 CANADA
FABRIQUE EN CORÉE
1-800-SAMSUNG (1-800-7267864)
www.SAMSUNG.COM/CA
LABOR
One year (Carry- in)
PARTS
One year
EXCLUSIONS (WHAT IS NOT COVERED)
MX-FS8000-ZC_ENG_131011.indd 20 2013-10-11 �� 1:27:19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Samsung MX-FS8000 Manuel utilisateur

Catégorie
Lecteur CD
Taper
Manuel utilisateur

dans d''autres langues