Fire Magic E1060S4LAN62 Mode d'emploi

Marque: Fire Magic

Modèle: E1060S4LAN62

Catégorie: Barbecues

Taper: Mode d'emploi

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

WARNING:

1. Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This

outdoor gas grill must be installed in accordance

with local codes and ordinances, or, in the absence

of local codes, with the latest National Fuel Gas

Code (ANSI Z223.1/NFPA 54), or Natural Gas and

Propane Storage and Handling Installation Code

(CSA-B149.1).

This appliance and its dedicated manual shutoff

valve must be disconnected from the gas-supply

piping system when testing the system at pressures

in excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas-

supply piping system by closing its dedicated

manual shutoff valve during any pressure testing

of the gas-supply system at pressures up to and

including ½ psig (3.5 kPa).

All electrical outlets in the vicinity of the grill must

be properly grounded in accordance with local

codes, or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

Certiﬁ ed to: ANSI Z21.58b-2012

CSA 1.6b-2012

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

SAFETY AND WARNING CODES

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂ ame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or the ﬁ re department.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

WARNING:

Improper installation, adjustment, alteration,

service, or maintenance can cause injury

or property damage. For proper installation,

refer to the installation instructions. For

assistance or additional information, consult

a qualiﬁ ed professional service technician,

service agency, or the gas supplier.

WARNINGS AND SAFETY CODES

10-32

OUTDOOR STAND-ALONE GAS GRILL

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

E660s, E790s, and E1060s

Proper operation of your grill requires

prompt and periodic maintenance. See

the CARE & CLEANING section for

details.

REV 2 - 1602021030

L-C2-401

ECHELON

diamond “A” series

E790s shown

IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION OU L’UTILISATION

ECHELON GRIL EXTÉRIEUR DE GAZ DU PORTATIF

DANGER:

SI VOUS SENTEZ LE GAZ :

1. Coupez l’admission de gaz de I’appariel.

2. Éteindre toute ﬂ amme nue.

3. Ouvrir le couvercle.

4. Si l’odeur persiste, éloignez-vous de

l’appareil et appelez immédiatement

le fournisseur de gaz ou le service

d’incendie.

AVERTISSEMENT:

1. Ne stockez pas ou n’employez pas

l’essence ou d’autres vapeurs et liquides

inﬂ ammables à proximité de ceci ou

d’aucun autre appareil.

2. Un cylindre de propane non relié pour

l’usage ne sera pas stocké à proximité

de ceci ou d’aucun autre appareil.

CONDITIONS DE CODE ET D’APPROVISIONNEMENT:

Ce gril doit être installé selon des codes et des ordonnances

locaux, ou, en l’absence des codes locaux, avec l’un ou l’autre

le plus défunt Code national de gaz de carburant (norme ANSI

Z223.1/NFPA 54), et Stockage de gaz naturel et de propane

et manipulation du code d’installation (CSA-B149.1).

Cet appareil et ses différents robinets d’isolement doivent être

démontés du gaz-fournissent le système sifﬂ ant en examinant

le système aux pressions au-dessus du ½ psig (kPa 3.5).

Cet appareil doit être isolé dans gaz-fournissent le système

sifﬂ ant par fermeture que ses différents robinets d’isolement

manuels pendant tous les essais sous pression du gaz-

fournissent le système aux pressions jusques et y compris

le ½ psig (kPa 3.5).

Toutes les sorties électriques à proximité du gril doivent être

correctement fondues selon des codes locaux, ou en l’absence

de local code, avec le code électrique national, ANSI/NFPA

70, ou le code électrique canadien, CSA C22.1, celui qui est

applicable.

Maintenez tout électrique-fournissent des cordes et carburant-

fournissent des tuyaux partis de n’importe quelle surface de

chauffage.

Certiﬁ é à la norme ANSI : Z21.58b-2012 / CSA 1.6b-2012

INSTALLATEUR : Laissez ces instructions avec le consommateur.

CONSOMMATEUR : Maintenez pour la future référence.

AVERTISSEMENT:

L’installation inexacte, l’ajustement, le

changement, le service, ou l’entretien

peuvent causer des dommages ou des

dégats matériels. Référez-vous à ce manuel.

Pour de l'aide ou des renseignements

supplémentaires, consultez un technicien

professionnel qualifié de service, une

agence de service ou le fournisseur de gaz.

SÛRETÉ ET CODES D’AVERTISSEMENT

• Ce gril est pour ultilisation à l’extérieur seulement.

Si l’appareil est entreposé à l’intérieur, enlever les

bouteilles et les laisser à l’extérieur.

• Ne pas ranger le gril immédiatement aprés l’avoir utilisé.

le laisser refroidir avant de le déplacer ou de la ranger.

Le non respect de cette mesure de sécurité pourrait

entraîner un incendie causant des dommages à la

propriété, des blessures ou la mort.

• Ne pas utiliser cet appareil sous une surface combustible.

• Ne pas utiliser cet appareil sous un auvent. Le non

respect de cette mesure de sécurité pourrait entraîner

un incendie ou des blessures.

• Dégagement minimal entre les parois latérales et l’arriére

de l’appareil et la construction combustible (45.7 cm à

partir des parois latérales et 45.7cm à partir de l’arriére).

• Le régulareur de pression de gaz prévu avec cet appareil

de cuisson à gaz pour l’extérieur doit être utilisé. Ce

régulateur est réglé pour une pression de sortie de 5

pouces de colonne de l’eau pour le gaz naturel, et 10

pouces pour le propane.

• LE RÉGULATEUR INCLUS D’APPAREILS EST ÉVALUÉ

POUR LE MAXIMUM DE 1/2 (LIVRES PAR POUCE

CARRÉ). SI VOTRE OFFRE DE GAZ EST 1/2 PLUS

GRAND QUE (LIVRES PAR POUCE CARRÉ), UN

RÉGULATEUR ADDITIONNEL DOIT ÊTRE INSTALLÉ

AVANT LE GRIL. VOIR LA SECTION DE CONDITIONS

D’OFFRE DE GAZ POUR LA PRESSION APPROPRIÉE

D’OFFRE DE GAZ.

• Ne couvrez jamais la surface entière de cuisine ou de

gril de gauffreuses ou de casseroles. La surchauffe se

produira et les brûleurs ne seront pas très performants

quand la chaleur de combustion est emprisonnée au-

dessous de la surface à cuire.

• Ne pulvérisez jamais l’eau sur une unité chaude de gaz,

comme ceci peut endommager des composants de

porcelaine ou de fer de fonte.

• Une fuite de GPL peut causer une incendie ou une

explosion si enflammée entraînant des blessures

corporelles graves ou la mort.

• Communiquez avec le fournisseur de GPL pour les

réparations ou pour disposer de qules bouteille ou du

GPL non utilisé.

INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE

REV 2 - 1602021030

L-C2-401

GETTING

STARTED

CONTENTS

To protect against electric shock, do not immerse cord or plugs in water or other liquid.

Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off

parts.

Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance

malfunctions or has been damaged in any manner. Contact the manufacturer for repair.

Do not let the cord hang over the edge of a table or touch hot surfaces.

Do not use an outdoor cooking gas appliance for purposes other than intended.

When connecting, ﬁ rst connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.

Use only a properly wired and inspected 120VAC (15 AMP minimum) Ground Fault Circuit Interrupter

(GFCI) GROUNDED 3-wire receptacle with this outdoor cooking gas appliance.

Never remove the grounding plug or use with an adapter of 2 prongs.

Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and

approved for outdoor use with a W-A marking.

ELECTRICAL SAFETY

REV 2 - 1602021030

L-C2-401

GETTING STARTED

REPLACEMENT COMMON PARTS LIST ...........................4

SINGLE SIDEBURNER UNIQUE PARTS LIST ................... 6

DOUBLE SIDEBURNER UNIQUE PARTS LIST .................7

POWER BURNER UNIQUE PARTS LIST............................8

MODEL SPECIFICATIONS TABLE.....................................9

STAND-ALONE GRILL WIRING DIAGRAM ......................10

STAND-ALONE GRILL DIMENSIONS TABLE ...................11

ELECTRICAL CONNECTIONS .......................................12

GRILL MAINTENANCE AND SAFETY INFORMATION .. 12

LIGHT SWITCH ........................................................... 12

INSTALLATION REQUIREMENTS ..................................13

ENSURE PROPER COMBUSTION AIR AND COOLING AIR-

FLOW

........................................................................ 14

PROPANE SAFETY INFORMATION ................................15

OPERATING THE UNIT SAFELY AND CORRECTLY ......15

WARNING ..................................................................15

INSTALLATION SAFETY GUIDELINES............................15

SAFE USE & MAINTENANCE OF PROPANE GAS

CYLINDERS .....................................................................17

INSTALLATION

INSTALLATION ...............................................................18

LOCATION PREPARATION ...........................................18

WHEELS AND CASTERS ............................................... 18

CONNECT THE GAS SUPPLY ........................................18

INSTALL ZONE DIVIDERS ............................................19

INSTALL THE SIDEBURNER SHELF (IF EQUIPPED) .....20

IDENTIFICATION OF GRILL CONTROLS .......................21

USE, CARE, & SERVICE

LIGHTING (IGNITION) INSTRUCTIONS ....................... 23

ELECTRONIC LIGHTING ........................................... 23

MANUAL LIGHTING .................................................. 23

SHUTTING OFF THE UNIT ......................................... 23

ROTISSERIE INSTRUCTIONS ....................................... 24

USING THE FOLDING SHELF ....................................... 25

PAPER TOWEL HOLDER ............................................... 25

REMOVING DRAWERS ................................................. 25

POWER BURNER ........................................................... 26

WOK COOKING ........................................................ 26

POWER BURNER INSTALLATION ................................ 26

POWER BURNER SAFETY .......................................... 26

STAINLESS STEEL POWER BURNER COVER ................. 26

ORIFICE INSPECTION, AND REPLACEMENT ............... 26

OPTIONAL INFRARED BURNER OPERATION ............. 27

ACCESSORIES ............................................................... 28

FIRE MAGIC

DRIP TRAY ............................................ 29

CARE & CLEANING ...................................................... 30

REPLACING HALOGEN BULBS ................................... 31

POWER SUPPLY FUSE REPLACEMENT ....................... 32

CONVERT GAS TYPE / CHECK BURNER ORIFICES .... 33

BURNER AIR SHUTTER ADJUSTMENT ....................... 36

ADJUSTING THE LOW FLAME SETTING ...................... 38

SAFETY.................................................................... 39

STAINLESS STEEL SIDEBURNER COVER ..................... 39

ORIFICE INSPECTION AND REPLACEMENT ................ 39

DOUBLE SIDEBURNER ................................................ 39

CONTROL PANEL REMOVAL ....................................... 41

NOTES PAGE ................................................................. 42

TROUBLESHOOTING .................................................... 43

WARRANTY .................................................................. 44

REPLACEMENT COMMON PARTS LIST

Fig. 4-1

To order replacement

parts, contact your

local Fire-Magic dealer.

Items in light gray are

not available on all

models.

E660s & E790s grills are

equipped with two drawers

on the right side of the unit.

Some items shown

are optional, or are

not available for

certain models. Your

model may vary, refer

to parts list table.

GETTING STARTED

REV 2 - 1602021030

L-C2-401

REPLACEMENT COMMON PARTS LIST (cont.)

REV 2 - 1602021030

L-C2-401

E660s E790s E1060s

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

Stainless cooking grid (set of 2 or 3) 3544-S-3 1 3539-S-3 1 23539-S-2 2

Flavor grid (set of 3 or 4) 3057-S-3 1 3056-S-3 1 3056-S-4 1

Main burner 3041-50 3 3041-50 3 3041-50 4

Heatshield kit 24177-05 3 24177-05 3 24177-05 4

Silicone gasket 24177-06 3 24177-06 3 24177-06 4

Infrared burner * 3050 1 3050 1 3050 1

Oven lid 24193-55 1 24188-55 1 24183-55 1

Oven lid w/ window 24193-54 1 24188-54 1 24183-54 1

Window (only)*‡ 24187-45 1 24187-45 1 24187-45 1

Warming rack 3673S-M 1 3675S-M 1 3674S-M 1

10.

Back burner assembly 24794-02 1 24789-02 1 24794-02 2

11.

Back burner cover 24794-010 1 24789-010 1 24784-010 1

12.

Zone separator 3061-S 2 3061-S 2 3061-S 3

13.

Heavy-duty rotisserie motor 3600-05M 1 3600-05M 1 3600-05M 1

14.

Heavy-duty rod 3606-40 1 3609-40 1 3607-40 1

15.

Heavy-duty rod knob 24187-16 1 24187-16 1 24187-16 1

16.

Meat holder (pair) 3613 1 3613 1 3613 1

17.

Counterbalance 3620E 1 3620E 1 3620E 1

18.

Grid lifter 3519 1 3519 1 3519 1

19.

Convertible regulator PR-4 1 PR-4 1 PR-4 1

20.

Control panel w/ back burner, raceway, and

wire harness

24394-15 1 24389-15 1 24384-15 1

21.

Valve manifold w/ back burner 24393-22 1 24388-22 1 24383-22 1

22.

Small knob 24182-42 2 24182-42 2 24182-42 3

23.

Large knob 24182-41 3 24182-41 3 24182-41 4

24.

LED disk (small) 24182-64 2 24182-64 2 24182-64 3

25.

LED disk (large) 24182-63 3 24182-63 3 24182-63 4

26.

Oven hood thermometer ‡

Grill top thermometer (window models) ‡

23305

3583

23305

3583

23305

3583

27.

Power supply w/ outlet 24387-18 1 24387-18 1 24387-18 1

28.

Drip tray 3087 1 3087 1 3087 1

29.

Drip tray liner (set of 4) 3557 1 3557 1 3557 1

30.

Wire harness for raceway ‡ 24194-26 1 24189-26 1 24184-26 1

31.

Back burner electrode *‡ 4199-52 1 4199-52 1 4199-52 2

* If equipped

‡ Not shown

REPLACEMENT COMMON PARTS LIST (cont.)

REV 2 - 1602021030

L-C2-401

E660s E790s E1060s

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

32.

Main burner electrode‡ 3199-72 3 3199-72 3 3199-72 4

33.

Natural gas oriﬁ ce(s) ‡ 3001-42-3 1 3001-38-3 1 3001-40-4 1

34.

Natural back burner gas oriﬁ ce(s) ‡ 3001-53-1 1 3001-51-1 1 3001-53-2 1

35.

Propane gas oriﬁ ce(s) ‡ 3001-54-3 1 3001-53-3 1 3001-53-4 1

36.

Propane back burner gas oriﬁ ce(s) ‡ 3001-63-1 1 3001-57-1 1 3001-63-2 1

37.

Natural smoker oriﬁ ce ‡ 3003-68-1 1 3003-68-1 1 3003-68-1 1

38.

Propane smoker oriﬁ ce ‡ 3003-77-1 1 3003-77-1 1 3003-77-1 1

39.

Smoker drawer assembly 24182-45 1 24182-45 1 24182-45 1

40.

12v / 10 watt halogen bulb ‡ 24187-15 2 24187-15 2 24187-15 3

41.

Light lens ‡ 24187-26 2 24187-26 2 24187-26 3

42.

Lamp assembly ‡ 24187-28 2 24187-28 2 24187-28 3

43.

Light switch 24182-46 1 24182-46 1 24182-46 1

44.

Light microswitch 24187-20 1 24187-20 1 24187-20 1

45.

Flash tube (left) ‡ 24187-29 1 24187-29 1 24187-29 1

46.

Flash tube (right) ‡ 24187-35 2 24187-35 2 24187-35 3

47.

Backburner ﬂ ex connector ‡ 3030-08 1 3030-08 1 3030-08 1

48.

Tool holder 25387-12 1 25387-12 1 25387-12 1

49.

Paper towel holder 25387-11 1 25387-11 1 25387-11 1

50.

Propane tank tray

(propane models only)

24336-36 1 24336-36 1 24336-36 1

51.

Propane regulator with hose

(propane models only)

5110-15 1 5110-15 1 5110-15 1

52.

Quick-disconnect hose ‡

(natural models only)

5110-03 1 5110-03 1 5110-03 1

53.

Power cord ‡ 25387-13 1 25387-13 1 25387-13 1

54.

Folding shelf 24336-15 1 24336-15 1 24336-15 1

55.

Fire Magic

cookbook ‡ 3595 1 3595 1 3595 1

* If equipped

‡ Not shown

E660s E790s E1060s

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

56.

Sideburner (burner only) ‡ 3279-35 1 3279-35 1 3279-35 1

57.

Sideburner assembly w/ shelf 24336-16 1 24336-16 1 24336-16 1

58.

Sideburner grid 3552 1 3552 1 3552 1

59.

Sideburner cap 3279-36 1 3279-36 1 3279-36 1

60.

Sideburner lid 24336-31 1 24336-31 1 24336-31 1

‡ Not shown

SINGLE SIDEBURNER UNIQUE PARTS LIST

DOUBLE SIDEBURNER UNIQUE PARTS LIST

Fig. 7-1

Note: See page 4-6 for common part

and number identification.

Some quantities may vary.

Grills equipped with a double

sideburner are available for 660s,

790s, and 1060s series.

1060s shown here.

REV 2 - 1602021030

L-C2-401

E660s E790s E1060s

Item Description Part No. Qty. Part No. Qty. Part No. Qty.

20.

Main control panel w/ raceway and wire harness 24394-16 1 24394-16 1 24394-16 1

21.

Main valve manifold 24193-22 1 24188-22 1 24383-28 1

56.

Double sideburner valve manifold 3281-22 1 3281-22 1 3281-22 1

57.

Double sideburner (only) ‡ 3279-32 2 3279-32 2 3279-32 2

58.

Double sideburner grid 3529-S 1 3529-S 1 3529-S 1

59.

Sideburner cap 3279-36 2 3279-36 2 3279-36 2

60.

Double sideburner cover 3281-07 1 3281-07 1 3281-07 1

61.

Convertible regulator

(for double sideburner valve manifold)

PR-4 1 PR-4 1 PR-4 1

62.

Double sideburner control panel N/A N/A 23281-12 1

63.

Double sideburner wire harness extension ‡ 34394-19 1 34394-19 1 34394-19 1

* If equipped

‡ Not shown

39 50

POWER BURNER UNIQUE PARTS LIST

Fig. 8-1

Note: See page 4-6 for common part

and number identification.

Some quantities may vary.

REV 2 - 1602021030

L-C2-401

E1060s

Item Description Part No. Qty.

20.

Main control panel w/ raceway and wire harness 24384-16 1

21.

Main valve manifold 24383-28 1

56.

Power burner valve manifold 3278-14 1

57.

Power burner (only) 3278-01B 1

58.

Power burner grid - stainless steel 3545-S 1

Power burner grid - porcelain cast 3545 1

59.

Power burner collimator 3279-09 1

60.

Power burner cover 3278-06 1

61.

Convertible regulator

(for power burner valve manifold)

PR-4 1

62.

Power burner control panel 23278-10 1

63.

Power burner wire harness extension ‡ 34384-19 1

* If equipped

‡ Not shown

MODEL SPECIFICATIONS TABLE

Table 1 E660s E790s E1060s

Main burner quantity

N/P oriﬁ ce drill size

#42 / #54

#38 / #53

#40 / #53

Back burner quantity

N/P oriﬁ ce drill size

#53 / #63

#51 / #57

#53 / #63

Single sideburner *

N/P oriﬁ ce drill size

#50 / #58 #50 / #58 #50 / #58

Double sideburner quantity*

N/P oriﬁ ce drill size

#50 / #58

Smoker drawer burner

N/P oriﬁ ce drill size

#68 / #77 #68 / #77 #68 / #77

Infrared searing burner *

N/P oriﬁ ce drill size

#45 / #55 #45 / #55 #45 / #55

Power burner *

Left N/P oriﬁ ce drill size

Right N/P oriﬁ ce drill size

- -

#30 / #50

#46 / #1.25

Input electrical requirements 120VAC / 15 AMP minimum / 60 Hz/ GFCI outlet

Nat to LP conversion kit (for standalone grills)

w/ tank tray model #

25386-21

Oven Lights Rating 12V / 10 watt halogen bulb

If equipped

REV 2 - 1602021030

L-C2-401

MODEL SPECIFICATIONS (cont.)

Note: In addition, a wire diagram speciﬁ c to your unit

can be found afﬁ xed to the inside of the control

panel.

STAND-ALONE GRILL WIRING DIAGRAM

E1060s model shown. Model wire diagrams may vary.

REV 2 - 1602021030

L-C2-401

Power supply

Wire harness

assembly

Valve

manifold

Light

switch

Main burner igniters

Backburner

igniter

Left oven

light

Oven light

micro switch

(not used for

Magic View)

Back

burner

Main

burner 1

Main

burner 2

Main

burner 3

Center oven

light

Right oven

light

Backburner

igniter

Smoker

igniter

For Magic

View only

Main

burner 4

Smoker

burner

Back

burner

LED disc

(small)

LED disc

(large)

sideburner

igniter

Side

burner

MODEL SPECIFICATIONS (cont.)

STAND-ALONE GRILL DIMENSIONS TABLE

Model Series

Height Width Depth

Floor to top

(with oven)

Floor to top

of shelf

(C)

Left to right Front to back

Cart base

(D)

(with shelves)

Cart base

(G)

Maximum

outer

(H)

Open

(A)

Closed

(B)

(E)

1 Up / 1 Down

(F)

E660s

w/ or w/o sIngle

sideburner

/8" 52" 37" 34

/4" 67

/2" 56" 26" 29

/4"

E660s

w/ double sideburner 60

/8" 52" 37" 53" 86

/4" 77" 26" 29

/4"

E790s

w/ or w/o sIngle

sideburner

/8" 52" 37" 40" 73

/4" 59

/4" 26 " 29

/4"

E790s

w/ double sideburner 60

/8" 52" 37" 58

/4" 92" 80

/4" 26" 29

/4"

E1060s

w/ or w/o sIngle

sideburner

/8" 52" 37" 53" 86

/4" 66

/4" 26 " 29

/4"

E1060s

w/ double sideburner

or Power burner

/8" 52" 37" 77

/4" 111" 93

/4" 26" 29

/4"

REV 2 - 1602021030

L-C2-401

1. The outdoor grill and surrounding area MUST

remain clear of ﬂ ammable substances such as

gasoline, yard debris, wood, etc.

2. The airﬂ ow through the vent space located below

the control panel must remain unobstructed.

3. When using propane gas:

a. The required ventilation openings in the

enclosure must be clear of debris. See the

PROPANE SAFETY INFORMATION section.

b. The propane cylinder, regulator, and rubber

hose must be in a location not subject to

temperature above 125° F (51° C).

4. The ﬂ ames on each burner burn evenly along

the entire burner with a steady ﬂ ame (mostly

blue). If burner ﬂ ames are not normal, check

and clean the oriﬁ ce and burner/venturi tubes

for insects and insect nests. A clogged tube can

lead to a ﬁ re beneath the grill. A proper ﬂ ame

pattern will ensure safe operation and optimal

performance. Adjust the air shutter as needed

(see AIR SHUTTER ADJUSTMENT).

5. The in-line gas valve or gas cylinder valve must

always be shut OFF when the grill is not in use.

6. The drip collector holes must be clear and

unobstructed. Excessive grease deposits can

result in a grease ﬁ re.

7. The back burner, sideburner, or IR burner cover

must be removed before using the burner.

8. Whenever reconnecting any wires, apply a

small amount of dielectric grease to the male

connector, then make the connection. This will

ensure conductivity and prevent moisture from

affecting the contact.

GRILL MAINTENANCE AND SAFETY INFORMATION

WARNING: NEVER cover the entire cooking or grill surface with griddles or pans. Overheating will occur, and

burners will not perform properly when combustion heat is trapped below the cooking surface.

CAUTION: NEVER spray water on a hot gas unit.

The grill serial identiﬁ cation number is located on the underside of the drip tray handle. It

is recommended that the drip tray ﬁ rst be removed and cleaned / emptied of its contents,

then turned over to view. The unit rating label is located inside of the control panel.

ELECTRICAL CONNECTIONS

A 120VAC (15 AMP minimum) GFCI GROUNDED

3-wire receptacle (not included) is required within

the vicinity of the grill to provide power to the unit.

• Observe all local codes.

• Verify proper polarity of the receptacle.

• If an extension cord is used, ensure it is a 3-wire

GROUNDED cord that is rated for the power of

the equipment, and is approved for outdoor

use with a W-A marking. DO NOT use 2-prong

adapters.

• DO NOT TAMPER WITH THE EXTENSION CORD

OR THE UNIT POWER-SUPPLY CORD.

Important: ONLY REPLACE THE OVEN LIGHTS

WITH 12V / 10 WATT HALOGEN

BULB(S).

REV 2 - 1602021030

L-C2-401

LIGHT SWITCH

The light switch is push button operated, and is

located on the right side of the control panel (see

Fig. 12-1). It controls the power to all lights.

Light

switch

Fig. 12-1

INSTALLATION REQUIREMENTS

Installation must be performed by a qualiﬁ ed professional

service technician.

This grill is designed for outdoor use only. DO NOT use this grill

inside a building, garage, enclosed area, or under any overhead

construction.

DO NOT use this grill in or on a recreational vehicle or boat.

Important: The grill is not insulated. Refer to the information

below to ensure all required clearances are met.

The grill must have a minimum clearance of 18" from

combustible materials/items AT ALL TIMES.

Side and Rear Wall Clearances

For the minimum clearances between the grill and any side or rear

walls, your setup must fall within one (or more) of the following:

A. Clearance between grill and combustible wall

• The grill must have a minimum of 18" right, left, and rear

clearance from any combustible wall (see Fig. 13-1).

B. Clearance between grill and strictly non-combustible wall

(i.e. brick wall, see Fig. 13-2)

• The grill must have a minimum of 4" right, left, and rear

clearance from any non-combustible wall.

(To allow for proper ventilation and prevent dangerous

overheating.)

Fig. 13-1 Clearance 'A' Diagram

Combustible

Min.

18"

(Clearance required for

right, left, and rear)

Fig. 13-2 Clearance 'B' Diagram

Non-combustible

Min.

(Clearance required for

right, left, and rear)

REV 2 - 1602021030

L-C2-401

INSTALLATION REQUIREMENTS (Cont.)

The control panel MUST remain removable for

servicing and air shutter adjustment (see PARTS

LIST).

THIS UNIT MUST NOT BE LOCATED IN A FULLY

ENCLOSED AREA OF ANY KIND.

ENSURE PROPER COMBUSTION AIR AND

COOLING AIRFLOW

Proper airﬂ ow (Fig. 14-1) MUST be maintained for

the grill to perform as it was designed. If airﬂ ow is

blocked, overheating and poor combustion will result.

Do not block the 1" (2.5 cm) front air inlet along the

bottom of the control panel or more than 75% of the

cooking grid surface with pans or griddles.

Note: The 1" (2.5 cm) front air space also allows

access to the drip tray.

CAUTION: Wind blowing into or across the rear

oven lid vent (Fig. 14-2) can cause

poor performance and/or dangerous

overheating. Orient the grill so that the

prevailing wind blows toward the front

of the grill (Fig. 14-3).

Important: A shut-off valve (not included) in

the gas line is required. It provides

for safety when the unit is not in use

and for convenient maintenance

and repair. It must be installed within

6 feet of the unit. Use a pipe joint

compound resistant to all gasses on

all male ﬁ ttings except ﬂ are ﬁ ttings.

GAS SUPPLY AND MANIFOLD PRESSURES:

For natural gas - normal 7" (17.78 cm) water column

(w.c.), minimum 5" (12.7 cm), maximum 10

" (26.7

cm). For propane gas - normal 11" w.c., minimum

10" (25.4 cm), maximum 13" (33 cm).

CORRECT

PLACE GRILL SO PREVAILING WIND

BLOWS TOWARD FRONT OF GRILL

YOU MUST PROTECT REAR OVEN

VENT FROM PREVAILING WIND

Rear oven lid vent

INCORRECT

Fig. 14-1 Ventilation

Fig. 14-2 Airﬂ ow direction - INCORRECT

Fig. 14-3 Airﬂ ow direction - CORRECT

REV 2 - 1602021030

L-C2-401

WHEN OPERATING THIS APPLIANCE WITH PROPANE, ALL INSTRUCTIONS AND

WARNINGS MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR

EXPLOSION CAUSING SERIOUS INJURY OR DEATH.

WARNING

THIS APPLIANCE MUST BE INSTALLED AND OPERATED ACCORDING TO THE INFORMATION BELOW.

FAILURE TO PROPERLY VENT THE CABINET MAY RESULT IN A FIRE OR EXPLOSION CAUSING

SERIOUS INJURY OR DEATH.

When using propane gas:

• Propane gas (also known as L.P. gas) is heavier than air and will accumulate or pool in an inadequately

vented enclosure or recessed area.

• A leaking gas connection or valve unintentionally left open will create a hazard.

• If a pool of propane gas is ignited, an explosion will occur. Adequate venting at the ﬂ oor level of the

cabinet eliminates this danger.

• DO NOT store a spare propane-gas cylinder in or near the unit.

INSTALLATION SAFETY GUIDELINES

THIS UNIT MUST BE INSTALLED IN SUCH A MANNER THAT ALL VENT OPENINGS ON THE CABINET

REMAIN CLEAR AND FREE OF ALL OBSTRUCTIONS AT ALL TIMES AND DURING ALL WEATHER

CONDITIONS.

The gas cylinder, regulator, and rubber hose must be in a location not subject to temps. above 125° F

(51° C).

WHEN A PROPANE CYLINDER IS INSTALLED INSIDE OF THE CABINET, THE GUIDELINES FOUND IN

THE SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS SECTION MUST BE FOLLOWED.

Every time you use the unit, make sure that:

1. The area around the unit is clear and free from combustible materials, gasoline and ﬂ ammable vapors/liquids.

2. There is no blockage of the airﬂ ow through the vent openings located on the cabinet.

3. The hose is inspected (if applicable). See SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS section.

DO NOT store any combustible materials, gasoline, and any other ﬂ ammable vapors/liquids in the vicinity of the

unit. Provide adequate clearance for servicing and operation.

OPERATING THE UNIT SAFELY AND CORRECTLY

PROPANE SAFETY INFORMATION

REV 2 - 1602021030

L-C2-401

Fig. 16-1 type coupleur rapide de ﬁ l de point culminant d’I

Valve

décompression

QCC

Type 1

Valve

Ajustage de précision

en laiton de ﬁ l de

point culminant

Indicateur

de niveau

de liquide

(facultatif)

Écrou de main avec le

ﬁ l de point culminant.

Régulateur

Passage

Tuyau

Volant de commande

main dans le sens des aiguilles d’une montre pour engager les

ﬁ ls et pour serrer jusqu’à ce que douillettement. L’utilisation des

pinces ou de la clé ne devrait pas être nécessaire. Seulement

le propane marqué par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens

contraire des aiguilles d’une montre jusqu’à isolé (ﬁ g. 16-1).

Important: Avant d’employer le gril, et ensuite chaque

fois que le cylindre est enlevé et rattaché,

examinez tous les raccordements pour déceler

les fuites. Arrêtez les valves de gril et ouvrez

la valve principale de cylindre, puis vériﬁ ez

les raccordements avec de l’eau savonneux.

Réparez toutes les fuites avant d’allumer le gril.

ATTENTION: Tournez toujours la valve principale de cylindre

de propane au loin après chaque utilisation,

et avant de déplacer le gril et le cylindre, ou

débrancher l’accouplement. Cette valve doit

rester fermée et le cylindre a débranché alors

que l’appareil n’est pas en service, quoique

l’écoulement de gaz soit arrêté par un dispositif

de sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque fois

avant que le gaz soit allumé. Un tuyau ﬁ ssuré ou efﬁ loché doit

être immédiatement remplacé.

Si l'appareil est stocké à l'intérieur, le cylindre doit être disconnected

et a enlevé. Des cylindres Disconnected doivent être stockés

dehors, hors de la portée des enfants, avec les prises de valve

ﬁ letées étroitement installées, et ne doivent pas être stockés dans

un bâtiment, le garage, ou n'importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de propane

dessous ou ne vous approchez pas de cet appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent de

plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS SUIVIE

EXACTEMENT, UN FEU CAUSANT LA MORT OU DES

DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

IMPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements.

LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.

CYLINDRE ET CONDITIONS ET

CARACTÉRISTIQUES DE CONNECTEUR

a. Des cylindres et les valves de gaz de propane doivent être

maintenus en bon état et doivent être remplacés s’il y a

des dommages évidents au cylindre ou à la valve.

b. Ce gril, une fois utilisé avec un cylindre, devrait être relié à

un gallon de la norme 5 (20lb.) cylindre de gaz de propane

équipé d’un OPD (remplissez au-dessus du niveau le

dispositif d’empêchement). L’OPD a été exigé sur tous les

cylindres vendus depuis octobre 1.1998 pour empêcher le

remplissage excessif.

c. Les dimensions de cylindre devraient être approximativement

12"(30.5cm) de diamètre et 18" (45.7cm) hauts. Des

cylindres doivent être construits et marqués selon les

caractéristiques pour des cylindres de gaz de propane du

département des ETATS-UNIS du transport (D.O.T.) ou

le niveau national du Canada, du CAN/CSA-B339, des

cylindres, des sphères et des tubes pour le transport des

marchandises dangereuses.

d. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit être

assuré le retrait de vapeur.

e. Le montage du régulateur de pression et le ﬂ exible (Fig. 16-1)

fourni avec cet appareil au gaz en plein air (modèles au

propane seulement) doit être utilisé. Assemblées d'origine et

régulateur de pression et le tuyau de remplacement doivent

être ceux spéciﬁ és par le fabricant pour le raccordement d'un

dispositif de cylindre de liaison identiﬁ ée comme de type I par

le 21.58-2005/CGA ANSI Z 1.6 à 2005 (voir liste des pièces

pour les informations de commande).

f. La valve de cylindre de gaz de propane doit être équipée

d’un dispositif d’accouplement de raccordement de

cylindre, décrit comme type I dans la norme déﬁ nie dans le

e. de paragraphe ci-dessus. Ce dispositif est généralement

décrit comme coupleur rapide de ﬁ l de point culminant.

g. Si votre cylindre de gaz de propane vient avec une prise

de la poussière, placez le bouchon anti-poussière sur la

sortie de valve de cylindre toutes les fois que le cylindre

n’est pas en service.

OPÉRATION DE COUPLEUR RAPIDE

Pour relier le regulator/hose à l’ajustage de précision de

valve de cylindre de gaz de propane: Serrez l’écrou de main

sur le régulateur au-dessus de l’ajustage de précision de ﬁ l

de point culminant sur la valve de cylindre. Tournez l’écrou de

FIXATION DU CYLINDRE DE GAZ DE PROPANE

1. Soulevez la poignée de

verrouillage pour ouvrir

le plateau et pour tirer à

l’extérieur.

3. Avec le cylindre de gaz en place et relié,

glissez le plateau de nouveau dans la poignée

de verrouillage de chariot et de serrure en

poussant fermement en bas.

2. Placez le cylindre de gaz de propane gainent fermement sur

le plateau avec la base insérée dans le trou central et le collier

s’ouvrant au dos. Suivez les instructions de relier ci-dessus

l’approvisionnement.

Fig. 16-2

Fig. 16-3

Fig. 16-5

Fig. 16-4

Ouverture

de Collier

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

Fig. 17-1 Type I Acme thread quick coupler

Pressure

relief

valve

QCC

Type 1

valve

Brass Acme

thread ﬁ tting

Liquid level

indicator

(optional)

Hand nut with Acme

thread

Regulator

Vent

Hose

Hand wheel

The use of pliers or a wrench should not be necessary. Only

cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until

detached (Fig. 17-1).

Important: Before using the unit, and after each time the

cylinder is removed and reattached, check

the hose for wear (see a.) and check all

connections for leaks. Turn off the unit valves

and open the main cylinder valve, then check

connections with soapy water. Repair any

leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit

and cylinder or disconnecting the coupling.

This valve must remain closed and the

cylinder disconnected while the appliance

is not in use, even though the gas ﬂ ow is

stopped by a safety feature when the coupler

is disconnected.

Carefully inspect the hose assembly each time before the

gas is turned on. A cracked or frayed hose must be replaced

immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected

cylinders must be

stored outdoors, out of the reach of children, with threaded

valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ﬁ ll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS

INJURY MAY OCCUR.

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and must be replaced if

there is visible damage to either the cylinder or valve. If the

hose is cut or shows excessive abrasion or wear, it must

be replaced before using the gas appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder

equipped with an OPD (Overﬁ ll Prevention Device).

The OPD has been required on all cylinders sold since

October 1,1998, to prevent overﬁ lling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the

Speciﬁ cations for Propane Gas Cylinders of the U.S.

Department of Transportation (D.O.T.) or the National

Standard of Canada, CAN/CSA-B339, Cylinders,

Spheres, and Tubes for Transportation of Dangerous

Goods.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

e. The pressure regulator and hose assembly (Fig. 17-1)

supplied with this outdoor gas appliance (L.P. models

only) must be used. Original and replacement pressure

regulator and hose assemblies must be those speciﬁ ed

by the manufacturer for connection with a cylinder

connecting device identiﬁ ed as Type I by the ANSI Z

21.58-2005/CGA 1.6-2005 (see PARTS LIST for ordering

information).

f. The propane-gas cylinder valve must be equipped with a

cylinder connection coupling device, described as Type I

in the standard deﬁ ned in paragraph e. above. This device

is commonly described as an Acme thread quick coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the

cylinder is not in use.

QUICK COUPLER OPERATION

To connect the regulator/hose assembly to the propane-

gas cylinder valve ﬁ tting: Press the hand nut on the regulator

over the Acme thread ﬁ tting on the cylinder valve. Turn the hand

nut clockwise to engage the threads and tighten until snug.

SECURING THE PROPANE-GAS CYLINDER

1. Lift latch handle to unlock

tray and pull outward.

3. With gas cylinder in place and connected, slide

tray back into cart and lock latch handle by

pushing ﬁ rmly downward.

2. Set propane-gas cylinder into the sleeve of the extended tray with

base inserted into center hole and collar opening to back. Follow

instructions above to connect supply.

Collar

Opening

Fig. 17-2

Fig. 17-3

Fig. 17-5

Fig. 17-4

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

LOCATION PREPARATION

Prepare a ﬂ at, level surface capable of supporting the weight

of the stand-alone grill and convenient to the gas supply if

connecting to a gas line.

WHEELS AND CASTERS

To lock a caster press down on the side of the lever with the

word "ON" stamped on it until it stops and the caster will

not turn. To unlock, press down on the side stamped "OFF."

INSTALL THE TOOL HOLDER AND PAPERTOWEL

HOLDER

The rectangular mounting bracket for the tool holder and

the paper towel holder come pre-attached to the sides of

the cart.

Unpack the holder portion, squeeze the open ends together

slightly, and install them into the mounting bracket (see Fig.

18-2). Next, release the hanger so that the ends extend out

through the holes in the top and bottom of the mounting

bracket (Fig. 18-3, 18-4).

When not in use, the racks may be folded back against the

wall of the grill (Fig. 18-3, 18-4).

CONNECT THE GAS SUPPLY

For connecting a propane unit to a portable propane tank,

read the safety warnings and follow the instructions in the

section SAFE USE AND MAINTENANCE OF PROPANE

GAS CYLINDERS.

For household propane or natural gas units:

1. Turn OFF the gas supply at the source. The quick

disconnect hose is pre-installed on the valve manifold at

the manufacturer. Run the hose through the hole in the

bottom rear of the stand-alone unit, to the gas supply.

2. A shut-off valve is required within 6 feet of the unit.

If shut-off valve is connected to end of gas supply

stub:

• Connect the quick disconnect hose to the shut-off

valve (see Fig. 18-5). Tighten securely.

If shut-off valve is installed in-line:

• Install the supplied ﬂ are adapter to the gas supply

using a pipe joint compound resistant to all gasses

(see Fig. 18-5). Tighten securely.

• Connect the quick disconnect hose to the ﬂ are

adapter (see Fig. 18-5). Tighten securely.

3. Turn all burner valves to the OFF position. Turn the gas

supply on. Then carefully check all gas connections

for leaks with a brush and soapy water before lighting.

NEVER USE A MATCH OR OPEN FLAME TO TEST

FOR LEAKS.

INSTALLATION

Fig. 18-1 Lock/unlock wheels

Fig. 18-3 Tool holder detail

Fig. 18-4 Papertowel holder detail

Fig. 18-5 Connecting to a gas line

Gas supply

Flare adaptor

(use on gas

supply stub only

if shut-off valve

installed in-line)

Quick

disconnect hose

(coming from unit)

Shut-off valve

(required, not

included, must be

installed within 6

feet of the unit)

Fig. 18-2 Install tool holder / papertowel holder

INSTALLATION (cont.)

Zone divider

Groove

Front

INSTALL THE FLAVOR GRIDS

Place the ﬂ avor grids directly onto the studs on the

burners. See Fig. 19-2. The ﬂ avor grids allow heat

from the burners to be evenly distributed throughout

the cooking area. They are stainless steel and will heat

and cool quickly, making your grill very responsive

to the changes you specify in grill temperature. They

are rust resistant and may be cleaned with standard

oven cleaners. Some discoloring will be seen with

use. This is normal for stainless steel and does not

affect the function.

CONNECT THE POWER SUPPLY TO LINE

POWER

Connect the supplied female receptacle end of

the cord to the male inlet plug located on the right

side of the grill. Then connect the male plug end of

the cord to a 120VAC (15 AMP minimum) GFCI

GROUNDED 3-wire receptacle.

WARNING: Electrical Grounding Instructions -

This appliance is equipped with a

three-pronged (grounding) plug for

your protection against shock hazard

and should be plugged directly into

a properly grounded three-prong

receptacle. Do not cut or remove the

grounding prong from this plug.

Fig. 19-2 Install ﬂ avor grids

Place onto studs

Fig. 19-1 Install zone dividers

Fig. 19-3 Connect to line power

Required 120VAC

(15 AMP minimum)

GFCI GROUNDED

3-wire receptacle

(not included)

Male inlet plug

Female receptacle

INSTALL ZONE DIVIDERS

Place the zone dividers as shown (Fig. 19-1) into

the grooves in the inner ﬁ rewall of the grill to allow

for maximum heat control in each zone. Remove

and store during rotisserie use.

This shelf comes separate from the grill for

convenience in shipping. The sideburner

shelf must be installed using the following

instructions before hooking up the grill to a

gas source.

INSTALL THE SIDEBURNER SHELF

1. Remove the protective plastic from the grill,

sideburner, and sideburner lids by carefully

peeling it off with your fingers. Do not use

tools.

2. Hold the sideburner shelf up against the left

side wall of the grill so that the holes in the shelf

line up with the four (4) threaded screw holes

in the side wall and the air-shutter end of the

sideburner venturi tube ﬁ ts around the brass

oriﬁ ce protruding from the side of the cart.

WARNING: It is critical for safety and for the

proper function of the sideburner

that the sideburner venturi tube with

air shutter be centered around and

completely cover the gas oriﬁ ce.

3. Insert and start screws with ﬁ ngers and then

tighten using a Phillips screwdriver.

Important: Take caution to not cross-thread

when tightening the screws.

Note: Upon completion, the air shutter must still

ﬁ t around the brass oriﬁ ce.

4. Connect the female connector on the end of the

hot surface ignitor wire to the male connector

coming from inside the grill.

5. Place the burner cap on top of the burner, as

shown in Fig. 20-3.

6. Place the grid so that it rests on the front

and back lips of the sideburner opening (Fig.

20-4).

7. Proceed to the section on AIR SHUTTER

ADJUSTMENT and complete the installation by

adjusting the air shutter. This will also test the

sideburner installation.

Air-shutter oriﬁ ce placement - under shelf

Fig. 20-1

Connecting the ignitor wires

Placing the burner cap

Fig. 20-2

Fig. 20-3

Final look

Fig. 20-4

Screw

Hole

Male

Female

Brass

oriﬁ ce

Air

shutter

Grate

Lid

Cap

Shelf

INSTALL THE SIDEBURNER SHELF (IF EQUIPPED)

La page est en cours de chargement...

Fire Magic E1060S4LAN62 Mode d'emploi

Marque: Fire Magic

Modèle: E1060S4LAN62

Catégorie: Barbecues

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Fire Magic E1060S4LAN62 User guide

Fire Magic E1060S4LAN62 Mode d'emploi

Fire Magic E1060S4LAN62 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents