TEAC Car Satellite TV System SR-L50 Manuel utilisateur

Catégorie
Lecteur CD
Taper
Manuel utilisateur

Ce manuel convient également à

9A09897100
SR-L50
CD Receiver
OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE
MANUAL DEL USUARIO
Z
?
ENGLISH
FRANÇAIS ESPAÑOL
2
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11) Only use attachments/accessories specified by
the manufacturer.
IMPORTANT SAFETY INSTRUCTIONS
12) Use only with the cart,
stand, tripod, bracket, or
table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid injury
from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
<
Do not expose this apparatus to dripps or
splashes.
<
Do not place any objects filled with liquids, such
as vases, on the apparatus.
<
Do not install this apparatus in a confined space
such as a book case or similar unit.
<
The apparatus draws nominal non-operating
power from the AC outlet with its POWER switch in
the off position.
AC POWER CORD CONNECTION
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT, FULLY INSERT.
CORDE DE CONNEXION CA
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQUAU FOND.
For CANADA Pour le CANADA
3
CAUTION
<
DO NOT REMOVE THE PROTECTIVE HOUSING
USING SCREWDRIVER.
<
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
<
IF THIS PRODUCT DEVELOPS TROUBLE, MAKE A
CONTACT WITH OUR SERVICEMAN, AND DO NOT
USE THE PRODUCT IN A TROUBLED STATE.
WARNING : TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the equipment and/or the
receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
Changes or modifications to this equipments not
expressly approved by TEAC CORPORATION for
compliance will void the users warranty.
For U.S.A.
Optical pickup :
Type : SLD104AU
Manufacturer : SONY Corporation
Laser output : Less than 0.5 mW on the objective
lens
Wavelength : 760 - 800 nm
This product has been designed and manufactured
according to FDA regulations title 21, CFR, chapter 1,
subchapter J, based on the Radiation Control for Health
and Safety Act of 1968, and is classified as class 1
laser product. There is not hazardous invisible laser
radiation during operation because invisible laser
radiation emitted inside of this product is completely
confined in the protective housings.
The label required in this regulation is shown
.
For U.S.A.
4
Contents
Thank you for choosing TEAC. Read this manual
carefully to get the best performance from this unit.
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Compact Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Names of Each Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CD
Playing a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Intro Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Shuffle Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programmed Playback . . . . . . . . . . . . . . . . . . . . . . . . . . 15
TUNER
Listening to the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
How to Preset Stations . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AUX
Listening to the External Sources . . . . . . . . . . . . . . . . . 19
TIMER
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Clock Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
IMPORTANT (for U.K.Customers)
DO NOT cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in
your home or the cable is too short to reach a power
point, then obtain an appropriate safety approved
extension lead or consult your dealer.
If nonetheless the mains plug is cut off, remove the
fuse and dispose of the plug
immediately, to avoid a
possible shock hazard by inadvertent connection to
the mains supply.
If this product is not provided with a mains plug, or
one has to be fitted, then follow the instructions given
below:
IMPORTANT. DO NOT make any connection to the
larger terminal which is marked with the letter E or by
the safety earth symbol |
or coloured GREEN or
GREEN-and-YELLOW.
The wires in the mains lead on this product are
coloured in accordance with the following code:
BLUE : NEUTRAL
BROWN : LIVE
As these colours may not correspond with the
coloured markings identifying the terminals in your
plug proceed as follows:
The wire which is coloured BLUE must be connected
to the terminal which is marked with the letter N or
coloured BLACK.
The wire which is coloured BROWN must be
connected to the terminal which is marked with the
letter L or coloured RED.
When replacing the fuse only a correctly rated
approved type should be used and be sure to re-fit the
fuse cover.
IF IN DOUBT CONSULT A COMPETENT
ELECTRICIAN.
VARING: APPARATEN INNEHÅLLER LASER KOMPONENT
MED STRÅLNING ÖVERSTIGANDE KLASS 1.
"ADVARSEL: USYNLIG LASERSTRÅLING VED ÅBNING
NAR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.
UNDGÅ UDSAETTELSE FOR STRÅLING"
"VAROITUS! SUOJAKOTELOA EI SAA AVATA. LAITE
SISÄLTÄÄ LASERDIODIN. JOKA LÄHETTÄ
(NÄKYMÄTÖNTÄ) SILMILLE VAARALLISTA
LASERSÄTEILYÄ".
ADVARSEL: USYNLIG LASERBESTRÅLING NÅR DENNE
DELEN ER ÅPEN OG SIKKERHETSSPERREN ER
UTKOBLET UNNGÅ UTSETTELSE FOR STRÅLING.
Obs! nätströmställaren skiljer ej hela apparaten fran
nätet.
ENGLISH
5
Before Use
Read this before operation
<
As the unit may become warm during operation,
always leave sufficient space around the unit for
ventilation.
<
The voltage supplied to the unit should match the
voltage as printed on the rear panel. If you are in
any doubt regarding this matter, consult an
electrician.
<
Choose the installation location of your unit
carefully. Avoid placing it in direct sunlight or close
to a source of heat. Also avoid locations subject to
vibrations and excessive dust, heat, cold or
moisture.
<
Do not place the unit on any high heat-producing
units like your amplifier/receiver.
<
Do not open the cabinet as this might result in
damage to the circuitry or electrical shock. If a
foreign object should get into the set, contact your
dealer or service agency.
<
When removing the power plug from the wall outlet,
always pull directly on the plug, never yank the
cord.
<
To keep the laser pickup clean, do not touch it, and
do not forget to close the disc tray when not using
the CD player.
<
Do not attempt to clean the unit with chemical
solvents as this might damage the finish. Use a
clean, dry cloth.
<
Keep this manual in a safe place for future
reference.
DO NOT MOVE THE UNIT DURING PLAYBACK
During playback, the disc rotates at high speed. Do
NOT lift or move the unit during playback. Doing so
may damage the disc.
WHEN MOVING THIS UNIT
When changing places of installation or packing the
unit for moving, be sure to remove the disc. Then,
press the power switch to turn the power off, and
disconnect the power cord. Moving this unit with the
disc loaded may result in damage to this unit.
Beware of condensation
When the unit (or a disc) is moved from a cold to a
warm place, or used after a sudden temperature
change, there is a danger of condensation; vapor in
the air could condense on the internal mechanism,
making correct operation impossible. To prevent
this, or if this occurs, leave the unit for one or two
hours with the power turned on. The unit will
stabilize at the temperature of its surroundings.
Maintenance
If the surface of the unit gets dirty, wipe with a soft
cloth or use diluted mild soap liquid. Be sure to
remove any excess completely. Do not use thinner,
benzine or alcohol as they may damage the surface
of the unit.
CAUTION
The product shall not be exposed to dripping or
splashing and that no object filled with liquids, such
as vases, shall be placed on the product.
Do not install this equipment in a confined space
such as a book case or similar unit.
Voltage Conversion
(General export models only)
Be sure to remove the power cord from the AC outlet
before repositioning the voltage converter switch.
1. Locate the voltage selector on the bottom of the
unit.
2. Using a flat-bladed screwdriver, set to the
appropriate 230V or 120V position according to
your area.
IN NORTH AMERICA USE ONLY ON 120 V SUPPLY.
6
Compact Disc
< Never use such chemicals as record sprays,
antistatic sprays or fluid, benzine or thinner to clean
the discs. Such chemicals will do irreparable
damage to the discs plastic surface.
<
Discs should be returned to their cases after use to
avoid dust and scratches that could cause the laser
pickup to skip.
<
Do not expose discs to direct sunlight or high
humidity and temperature for extended periods.
Long exposure to high temperatures will warp the
disc.
<
CD-R discs are more sensitive to the effects of heat
and ultraviolet rays than ordinary CDs. It is
important that they are not stored in a location
where direct sunlight will fall on them, and which is
away from sources of heat such as radiators or
heat-generating electrical devices.
<
Printable CD-R discs arent recommended, as the
label side might be sticky and damage the unit.
<
Do not stick papers or protective sheets on the
discs and do not use any protective coating spray.
<
Use a soft oil-based felt-tipped pen to write the
information on the label side. Never use a ball-point
or hard-tipped pen, as this may cause damage to
the recorded side.
<
Never use a stabilizer. Using commercially available
CD stabilizers with this unit will damage the
mechanisms and cause them to malfunction.
<
Do not use irregular shape CDs (octagonal, heart-
shape, etc.). CDs of this sort can damage the unit.
Discs which can be played on this unit:
Conventional audio CDs bearing the CD-DA logo
on the label:
?
Properly finalized CD-R discs
Note:
<
Depending on the quality of the disc and/or the
condition of the recording, some CD-R discs may not
be playable.
<
CD-RW discs cannot be played on this unit.
<
Copy-protected discs and other discs which do not
conform to the CD standard may not play back
correctly in this player.
If you use such discs in this unit, TEAC Corporation
and its subsidiaries cannot be responsible for any
consequences or guarantee the quality of
reproduction. If you experience problems with such
non-standard discs, you should contact the
producers of the disc.
< Always place the disc on the disc tray with the label
side uppermost. (Compact discs can be played or
recorded only on one side.)
<
To remove a disc from its storage case, press down
on the center of the case and lift the disc out,
holding it carefully by the edges.
How to remove the disc
How to hold the disc
<
Should the disc become dirty, wipe the surface
radially with a soft, dry cloth.
< If you are in any doubt as to the care and handling
of a CD-R disc, read the precautions supplied with
the disc, or contact the disc manufacturer directly.
ENGLISH
7
Connection
How to connect external sources
< Read instructions of each component you intend to
use with this unit.
<
Make sure to connect:
<
Be sure to insert each plug securely. To prevent
hum and noise, do not bundle the connection cords
with the power cord or speaker cord.
CAUTION: Do not plug the power cord of any
component into AC outlets and do not turn their
POWER switches on until all connections have been
performed.
Connection of FM antenna
(U.S.A./Canada and General export models only)
Connect the lead-type FM antenna to the FM antenna
terminal. Secure it in the location providing optimum
reception.
In an area where FM signals are weak, 75-ohm
unbalanced-type outdoor FM antenna (3 elements or
more) is recommended.
LINE OUT
LR
VCR, DVD PLAYER, ETC.
L
white
red
R
L
R
white
red
white
red
white
red
8
Names of Each Control
TOP
FRONT
REAR
REMOTE CONTROL
A B
I J
QRS
C D E F
NP O
K LG H M
A B
C
Y
J
Z
L
R
O
D
E
S
C
V
W
X
Q
F
M
SIDE
T
U
ENGLISH
9
SNOOZE button
After the on time is reached, use this button to turn
the unit off for 5 minutes.
BASS CONTROL knob
Use this control knob to adjust the bass level.
POWER switch
Press this switch to turn the unit on and off.
MEMORY/CLOCK ADJ button
Use this button to program tracks or to adjust the
clock.
FUNCTION button
Press this button repeatedly to select a function.
Select CD to play a disc.
Select TUNER to listen to the radio.
Select AUX to listen to the external sources
connected to the AUX input jacks.
TUNING button
Press this button up or down to tune in a station.
Remote sensor
Disc tray
Display
VOLUME button
Press this button up or down to adjust the volume.
OPEN/CLOSE button (L)
Use this button to open and close the disc tray.
STOP button (H)
Use this button to stop playback.
PLAY/PAUSE button (y/J)
Use this button to start or pause playback.
SKIP/SEARCH buttons
(.
m
/
,
/)
Press these buttons to skip tracks.
Hold down these buttons to search for a part of a
track.
REPEAT/PRESET button
Use this button to change the repeat mode or select
a preset number and station.
Speakers (stereo)
P
O
N
M
L
K
J
I
H
G
F
E
D
C
B
A
BAND button
Use this button to select FM or AM.
DISPLAY button
Use this button to change the display mode.
TIMER/SLEEP button
Use this button to set the timer or sleep timer.
DIMMER button
Use this button to dim the display and unit lighting.
PHONES
Insert the headphones plug into the PHONES jack,
and adjust the volume.
Both stereo and monaural earphones can be used
with this unit.
Numeric buttons
SHUFFLE button
Use this button to select shuffle playback mode.
INTRO button
Use this button to start the Intro Check.
MUTING button
To cut the sound temporarily, press the MUTING
button. Press the MUTING button again to restore
the sound. If you change the volume during the
muting, the muting will be canceled.
BASS BOOST button
Press this button to switch bass boost on and off.
AUX IN jacks
Connect external sources to these jacks.
FM antenna terminal (with U.S.A./Canada and
General export models)
Connect lead-type FM antenna to this terminal.
FM feeder antenna (with EUROPE model)
Tune in an FM station and extend the lead to find the
best position for the reception. Then fix it to the wall
with thumb tacks or the like.
AC Power Cord
Plug this AC power cord into an AC wall socket.
C
B
A
Z
Y
X
W
V
U
T
S
R
Q
The equipment draws nominal nonoperating
power from the AC outlet with its POWER switch
in the OFF position.
10
The provided Remote Control Unit allows the unit to be
operated from a distance.
When operating the remote control unit, point it
towards the REMOTE SENSOR on the front panel of the
unit.
<
Even if the remote control unit is operated within the
effective range, remote control operation may be
impossible if there are any obstacles between the
unit and the remote control.
<
If the remote control unit is operated near other
appliances which generate infrared rays, or if other
remote control devices using infrared rays are used
near the unit, it may operate incorrectly. Conversely,
the other appliances may operate incorrectly.
Battery Installation
Remove the battery compartment cover.
Insert two AAA (R03, SUM-4) dry batteries. Make
sure that the batteries are inserted with their
positive +
and negative _ poles positioned
correctly.
Close the cover.
Battery Replacement
If the distance required between the remote control
unit and main unit decreases, the batteries are
exhausted. In this case replace the batteries with new
ones.
3
2
1
Precautions concerning batteries
< Be sure to insert the batteries with correct positive
+
and negative _ polarities.
<
Use batteries of the same type. Never use different
types of batteries together.
<
Rechargeable and non-rechargeable batteries can
be used. Refer to the precautions on their labels.
<
When the remote control unit is not to be used for a
long time (more than a month), remove the batteries
from the remote control unit to prevent them from
leaking. If they leak, wipe away the liquid inside the
battery compartment and replace the batteries with
new ones.
<
Do not heat or disassemble batteries and never
dispose of old batteries by throwing them in a fire.
Remote Control Unit
RESET Switch
In the following cases, function buttons may not
work properly.
1) When the system is damaged by some electrical
shock.
2) When the power is irregular or has electrical
noise.
In these cases, press the RESET switch once or
twice lightly with a pencil or a ball-point pen.
Press the POWER switch to turn the unit ON.
Press the FUNCTION button repeatedly to select
CD.
<
When no disc is in the unit, no dISC will be
displayed.
Press the OPEN/CLOSE button (L) to open the disc
tray.
Place a disc with the printed label face up.
<
Never place more than one disc in the CD player.
<
The total number of the tracks and total play time of
the disc is displayed.
<
It takes a few seconds for the unit to read the
contents of the disc. No button will work during
reading. Wait until the total number of the tracks
and total play time of the disc is displayed.
4
3
2
1
11
ENGLISH
Playing a CD (1)
Press the OPEN/CLOSE button (L) to close the disc
tray.
Press the PLAY/PAUSE button (y
/J ) to start
playback.
Playback starts from the first track.
When playback of all the tracks has finished, the
unit stops automatically.
6
5
1 2 64 3 5
To stop playback
Press the STOP button (H) to stop playback.
To suspend playback temporarily (pause mode)
Press the PLAY/PAUSE button (y/J). Playback
stops at the current position.
To resume playback, press the PLAY/PAUSE button
(y
/J) again.
To skip to the next or a previous track
During playback, press the SKIP/SEARCH button
(.
m
or
,
/) repeatedly until the desired
track is found. The selected track will be played
from the beginning.
In the stop mode, press the SKIP/SEARCH button
(.
m
or
,
/) repeatedly until the desired
track is found, and press the PLAY/PAUSE button
(y/J) to start playback from the selected track.
<
When the .
m
button is pressed once during
playback, the track being played will be played from
the beginning. To return to the beginning of the
previous track, press the .
m
button twice.
<
During programmed playback, the next or previous
track in the program is played.
C
B
A
12
Playing a CD (2)
CF D
BA
Search for a part of a track
During playback, hold down the SKIP/SEARCH
button (.
m
or
,
/) and release it when
the part you want to listen to is found.
Direct access play
Press the numeric buttons corresponding to the
required track. The player starts from the specified
track directly.
Example 1:
To select the track No.5:
Example 2:
To select the track No.23:
E
D
13
ENGLISH
DISPLAY button
During playback, press this button repeatedly to
change the display mode as follows:
<
Clock display and timer mode display appears for 4
seconds and returns to original display.
<
In the stop mode, remaining time of the disc cannot
be selected.
F
Playing time of the current track
Remaining time of the disc
Clock display
Timer mode display
Intro Check
The Intro Check function allows only the beginning of
each track to be played for 10 seconds.
<
This function is operational both in the stop mode
and during normal playback.
Press the INTRO button.
The INTRO indicator lights in the display, and the Intro
Check will start.
<
To return to the normal playback, press the INTRO
button again.
<
To stop the Intro Check function, press the STOP
button (H
).
<
The Intro Check function also works together with
SHUFFLE or REPEAT ONE/ALL functions.
<
The Intro Check function also works together with
the PROGRAM function.
14
Repeat Playback
Every time the REPEAT/PRESET button is pressed, the
REPEAT indicator lights or blinks, and the mode is
changed as follows :
Repeat one track
Press the REPEAT/PRESET button once during
playback. The repeat indicator blinks.
The track being played will be played repeatedly. If
you press the SKIP/SEARCH button (.m
or
,/
) or the numeric buttons and select
another track, the track you select will be played
repeatedly.
It is also possible to select a track to be repeated in
the stop mode. Press the REPEAT/PRESET button
and then select the track number by pressing the
SKIP/SEARCH button (.m
or ,/) or the
numeric buttons. Press the PLAY/PAUSE button
(y
/J) to start playback.
Repeat all the tracks
All the tracks of the disc will be played repeatedly.
Press the REPEAT/PRESET button twice. The repeat
indicator lights steadily.
<
During program playback, only the programmed
tracks will be played in order repeatedly.
<
If one of the following buttons is pressed, repeat
mode will be canceled:
OPEN/CLOSE button (L
)
STOP button (H
)
POWER switch
FUNCTION button
REPEAT/PRESET
repeat one track
repeat all the tracks
(off)
Shuffle Playback
Tracks can be played randomly.
Press the SHUFFLE button in the stop or play mode.
The tracks will be played randomly.
<
If you press the SKIP/SEARCH button (
,
/)
during shuffle playback, next track will be randomly
selected and played.
If you press the SKIP/SEARCH button (.
m
),
the currently played track will be played from the
beginning.
A track cannot be replayed during shuffle playback.
<
To stop shuffle playback, press the STOP button (H).
<
To cancel the shuffle playback mode, press the
SHUFFLE button.
<
If one of the following buttons is pressed, shuffle
mode will be canceled:
OPEN/CLOSE button (L
)
STOP button (H
)
POWER switch
FUNCTION button
15
ENGLISH
Within 10 seconds, press the MEMORY/CLOCK ADJ
button.
The track is programmed, and P-02 is displayed.
Repeat steps and to program more tracks.
<
You can program up to 20 tracks.
<
You can also use the front panel buttons to select a
track number. In this case, press the SKIP/SEARCH
button to select a track number and then press the
MEMORY/CLOCK ADJ button while MEMORY is
blinking on the display.
<
To cancel the program mode, press the STOP button
(H
).
When the selection of track numbers is completed,
press the PLAY/PAUSE button (y
/J ) to start
program playback.
If the PLAY/PAUSE button (y/J) isnt pressed
within 10 seconds, the MEMORY indicator will go
off. In that case, press the MEMORY/CLOCK ADJ
button and then press the PLAY/PAUSE button
(y
/J) to start program playback.
The programmed contents are kept in memory even
after the FUNCTION button is pressed or the power
is turned off.
4
32
3
Up to 20 tracks can be programmed in the desired
order.
<
Shuffle playback does not work during program
playback.
<
Insert a disc and select CD before beginning
programming.
Press the MEMORY/CLOCK ADJ button in the stop
mode.
MEMORY indicator blinks, and P-01 appears on
the display.
Within 10 seconds, press the numeric buttons to
select a track.
Example 1:
To select the track No.5:
Example 2:
To select the track No.23:
<
If the numeric buttons arent pressed within 10
seconds, program mode will be canceled.
2
1
Programmed Playback (1)
2
4
1 3
16
Programmed Playback (2)
To cancel the program playback mode
Press the STOP button (H).
MEMORY indicator disappears, but the
programmed contents arent lost.
To return to the program mode, press the
MEMORY/CLOCK ADJ button.
To clear program
In the stop mode, do either of the following to clear
the program:
Press the OPEN/CLOSE button (L
) and open it.
Press the MEMORY/CLOCK ADJ button and then the
STOP button (H
).
<
If the unit is disconnected from the power supply,
the programmed contents will be cleared.
To check the programmed order
In the stop mode, press the MEMORY/CLOCK ADJ
button repeatedly to show the track numbers that
have been stored in memory.
To add a track to the end of the program
In the stop mode, press the MEMORY/CLOCK ADJ
button repeatedly until a track number (00) appears
on the display.
Select a track number by pressing the numeric
buttons, and then press the MEMORY/CLOCK ADJ
button.
The track is added to the end of the program.
To overwrite the program
In the stop mode, press the MEMORY/CLOCK ADJ
button repeatedly until the track number to be
changed appears on the display.
Select a new track number by pressing the numeric
buttons, and then press the MEMORY/CLOCK ADJ
button.
MEMORY/CLOCK ADJ
Numeric buttons
STOP
ENGLISH
17
Listening to the Radio
Press the POWER switch to turn the unit ON.
Press the FUNCTION button repeatedly to select
TUNER.
Press the BAND button to select FM or AM.
Select the station you want to listen to (auto
selection).
Press the TUNING button up or down until the
frequency display begins to change.
When a station is tuned in, the tuning process will
stop automatically.
<
Press the TUNING button again to stop the auto
selection.
4
3
2
1
Selecting stations which cannot be
tuned automatically (manual
selection).
Press the TUNING button up or down repeatedly
until the station you want to listen to is found.
If the reception is poor
AM broadcast
Turn around the unit to find the best position for AM
stations.
FM broadcast
For a good reception, turn around the antenna so
that you can get the stations clearly.
3
1 2 4
18
How to Preset Stations
In each band, up to 10 stations can be stored in preset
memories.
Press the BAND button to select FM or AM.
Press the TUNING button and tune in a station to be
stored as a preset station.
Press the MEMORY/CLOCK ADJ button.
Within 10 seconds, select a preset channel to store
the station using the REPEAT/PRESET button.
4
3
2
1
Within 10 seconds, press the MEMORY/CLOCK ADJ
button.
<
If you press the numeric buttons (10) of the remote
control unit, you can store the station directly. In
this case you dont have to press the
MEMORY/CLOCK ADJ button.
To store more stations, repeat steps to .
How to select preset stations
Press the BAND button to select FM or AM.
Press the REPEAT/PRESET button repeatedly and
select a preset channel.
If you press the numeric buttons (10) of the remote
control unit, you can select a preset channel
directly. To select preset number 10, press 0 of
the remote control unit.
2
1
51
5
41 21
253
ENGLISH
19
The power can be switched off at the specified time.
When the power is on, press the TIMER/SLEEP (or the
SLEEP button of the remote control unit) button
repeatedly until the desired time appears on the
display.
The sleep time can be changed at 10-minute intervals.
TIMER/SLEEP
Sleep Timer
(OFF)
90
80 10
70
Listening to the External Sources
You can connect external sources such as VCR deck
or TV to the AUX input jacks.
Press the POWER switch to turn the unit ON.
Press the FUNCTION button repeatedly to select
AUX.
2
1
1 2
20
Clock Adjustment
In the CD mode or the TUNER mode, press the
DISPLAY button to select clock display.
: blinks in the clock display.
<
If the AUX is selected or the unit is off, press and
hold the MEMORY/CLOCK ADJ button for 2 or more
seconds, and continue the procedure from step .
<
Press the STOP button to cancel the time setting. (In
the TUNER mode, press the DISPLAY button.)
Within 4 seconds, press and hold the
MEMORY/CLOCK ADJ button for 2 or more seconds.
Press the .m
or ,/ button to select
12H or 24H.
If you select 12H, AM indicator appears in the
morning and PM indicator appears after noon.
<
In the TUNER mode, use the TUNING button.
Press the MEMORY/CLOCK ADJ button.
4
3
2
3
1
Press the .mor,/ button to set the
current hour.
<
In the TUNER mode, use the TUNING button.
Press the MEMORY/CLOCK ADJ button.
Press the .m
or,/ button to set the
current minute.
<
In the TUNER mode, use the TUNING button.
Press the MEMORY/CLOCK ADJ button to finish the
time setting mode.
The clock starts from 00 second.
<
If the unit is disconnected from the power supply for
more than 3 minutes, the clock and timer setting will
be reset.
<
If the unit is disconnected for less than 3 minutes
the time displayed may not be correct.
8
7
6
5
MEMORY/CLOCK ADJ
DISPLAY .m ,/
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

TEAC Car Satellite TV System SR-L50 Manuel utilisateur

Catégorie
Lecteur CD
Taper
Manuel utilisateur
Ce manuel convient également à