Pioneer DJ Equipment DJM-2000NXS Manuel utilisateur

Operating Instructions

Mode d’emploi

Bedienungsanleitung

DJM-2000NXS

DJM-2000nexus

DJ MIXER

TABLE DE MIXAGE

DJ-MISCHPULT

http://pioneerdj.com/support/

The Pioneer DJ support site shown above offers FAQs, information on software and various other types of

information and services to allow you to use your product in greater comfort.

Le site de support DJ de Pioneer indiqué ci-dessus propose une FAQ, des informations sur le logiciel et divers

types d’informations et de services qui permettent une utilisation plus confortable de ce produit.

Die oben gezeigte Pioneer DJ-Support-Website enthält häufig gestellte Fragen, Informationen über Software

und andere wichtige Informationen und Dienste, die Ihnen helfen, Ihr Produkt optimal zu verwenden.

http://rekordbox.com/

For various types of information and services regarding rekordbox™, see the Pioneer website above.

Pour les différents types d’informations et de services concernant rekordbox™, consultez le site Pioneer

ci-dessus.

Weitere Informationen und Dienste bezüglich rekordbox™ finden Sie auf der oben angegebenen

Pioneer-Website.

Français DeutschEnglish

2

En

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After

you have finished reading the instructions, put them away in a safe place for future reference.

In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings.

However the method of connecting and operating the unit is the same.

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the side panel.

D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 5 cm at rear, and 3 cm at each side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left unused

for a long period of time (for example, when on

vacation).

D3-4-2-2-1a_A1_En

CAUTION

The POWER switch on this unit will not completely

shut off all power from the AC outlet. Since the power

cord serves as the main disconnect device for the

unit, you will need to unplug it from the AC outlet to

shut down all power. Therefore, make sure the unit

has been installed so that the power cord can be

easily unplugged from the AC outlet in case of an

accident. To avoid fire hazard, the power cord should

also be unplugged from the AC outlet when left

unused for a long period of time (for example, when

on vacation).

D3-4-2-2-2a*_A1_En

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_A1_En

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used

electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to

designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential

negative effects on the environment and human health.

K058b_A1_En

3

En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement.

S002*_A1_En

WARNING

Store small parts out of the reach of children and

infants. If accidentally swallowed, contact a doctor

immediately.

D41-6-4_A1_En

4

En

Contents

How to read this manual

In this manual, names of channels and buttons indicated on the prod-

uct, names of menus in the software, etc., are indicated within square

brackets ([ ]). (e.g. [MASTER] channel, [ON/OFF], [File] menu)

Before start

Features ....................................................................................................... 5

What’s in the box ........................................................................................ 5

Connections

Rear panel ................................................................................................... 6

Connecting input terminals ....................................................................... 7

Connecting output terminals .................................................................... 7

Connecting to the control panel ................................................................ 8

Connecting a computer ............................................................................. 8

About the USB audio driver software ....................................................... 8

Operation

Control Panel ............................................................................................ 11

Basic Operation ........................................................................................ 12

Advanced Operations ............................................................................... 14

List of MIDI Messages .............................................................................. 20

Types of BEAT EFFECT .............................................................................. 25

Changing the settings

Setting preferences .................................................................................. 27

About the auto standby function ............................................................. 27

Additional information

Troubleshooting ........................................................................................ 28

About the liquid crystal display ............................................................... 29

About trademarks and registered trademarks ...................................... 29

Block Diagram .......................................................................................... 30

Specifications............................................................................................ 31

5

En

English

Before start

Features

This unit is a high-performance DJ mixer designed for professional DJs,

which, in addition to its high sound quality design, is equipped with a

multi-touch panel and various types of interface and effect functions

enabling new styles of DJ performing.

TOUCH PANEL EFFECT

This unit uses a large 5.8-inch LCD multi-touch panel. When

used in combination with effect functions ([BEAT SLICE REMIX],

[FREQUENCY MIX] and [SIDECHAIN REMIX]), operations can be per-

formed intuitively while checking the effect by sight and sound.

 BEAT SLICE REMIX

The track for the specified channel can be sampled and looped. The

track that is looping can be arranged by operating the touch panel, so

new loop phrases can be created on the spot.

 FREQUENCY MIX

The track frequencies are divided into seven bands and displayed graphi-

cally. Fader control on the touch panel makes it easier to grasp the

details and mix two channels or swap instruments (parts).

 SIDECHAIN REMIX

The sound of a specific channel can be used as the trigger to apply

effects to the sound of other channels. Operation of the touch panel’s

pad makes it possible to process sound dynamically.

INST FX

This unit is equipped with six types of effects (NOISE, ZIP, CRUSH, JET,

HPF, LPF). Effects can be obtained simply by turning the [FILTER] con-

trols for the different channels for improvisational performances, and the

desired effects can be achieved by adjusting the [PARAMETER] control.

BEAT EFFECT

The DJM series’ well-received BEAT EFFECT function has been

carried over and further evolved. This unit is equipped with an

[EFFECT FREQUENCY] function allowing the amount of the effect

applied to be adjusted by frequency range, for even greater playing

freedom than before.

PRO DJ LINK

When a Pioneer DJ player supporting PRO DJ LINK (e.g. CDJ-2000nexus,

CDJ-2000, CDJ-900), a computer on which rekordbox is installed and this

unit are connected by LAN cable, the PRO DJ LINK functions below can

be used.

For details, see About PRO DJ LINK on page 14.

 SD & USB Export

 rekordbox LINK Export

 SYNC MASTER

 LIVE SAMPLER

 LINK MONITOR

 STATUS INFORMATION

SOUND CARD

This unit is equipped with sound card/USB audio interface allowing up

to four audio sources from one computer to be assigned to the different

channels and mixed. Furthermore, the master channel output signals

can be output to the computer, a great convenience for example for

recording the mixed sound.

CH FADER

Compared to the previous DJM-2000, this unit uses a high performance

channel fader with improved endurance against deterioration due to

dust or liquid getting on the fader. Smooth operation is maintained even

in rough usage environments.

HIGH SOUND QUALITY

Measures have been taken to improve sound quality for both the digital

and analog inputs and outputs. Sound processing with 96 kHz sampling,

a 24-bit high sound quality A/D converter and a 32-bit high sound quality

D/A converter achieves more powerful, higher grade sound.

This unit supports 48 kHz 16 bit, 48 kHz 24 bit and 44.1 kHz 16 bit USB

audio signals.

What’s in the box

! CD-ROM

! USB cable

! Power cord

! Warranty card

! Operating instructions (this document)

6

En

Connections

Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.

Refer to the operating instructions for the component to be connected.

Connect the power cord after all the connections between devices have been completed.

Be sure to use the included power cord.

Rear panel

SIGNAL GND

CD

L

R

L

R

PHONOCDLINE

CONTROL

OUT

IN

TRS

RL

R

L

RL(MONO) RL(MONO)

COMPUTER 1

COMPUTER 2

LINK

CH 3

CH 1

CH 4CH 2

CH2CH3CH4CH1

DIGITAL

SIGNAL GND

CD

1GND

-6dB -3dB 0dB

2HOT

3COLD

CD

L

R

PHONO

POWER

AC IN

OFF

ON

MASTER

ATT.

DIGITAL

CD DIGITAL

L

R

CDLINE

CONTROL

CD DIGITAL

CH 3CH4

MASTER1

MASTER2

REC OUT

BOOTH SENDRETURN

DIGITAL

CH 1CH2

USB

MIDI OUT

1 2 63 345 2345 a

bc

7 85 6 3 759

de

fgkhijl

1 POWER button (page 12)

Turns this unit’s power on and off.

2 PHONO terminals (page 7)

Connect to a phono level (MM cartridge) output device. Do not input

line level signals.

3 CD terminals (page 7)

Connect to a DJ player or a line level output component.

4 SIGNAL GND terminal (page 7)

Connects an analog player’s ground wire here. This helps reduce

noise when the analog player is connected.

5 CD, DIGITAL (page 12)

Selects the analog signal input terminals (CD) or the digital signal

input terminals (DIGITAL IN).

6 LINE terminals (page 7)

Connect to a cassette deck or a line level output component.

7 CONTROL (page 7)

Connect using a control cord (included with Pioneer DJ players).

8 DIGITAL OUT terminal (page 7)

Outputs the master channel audio signals.

9 DIGITAL IN terminal (page 7)

Connect these to the digital coaxial output terminals on DJ players,

etc. The sound may be momentarily interrupted when the output

signal sampling frequency is switched.

a Kensington security slot

b USB (page 8)

Connect to a computer.

c MIDI OUT terminal (page 7)

Connects this to the MIDI IN terminal on an external MIDI

sequencer.

d LINK terminal (page 7)

Connect these to the LINK terminals on Pioneer DJ players or the

LAN ports of computers on which rekordbox is installed (PRO DJ

LINK).

When connecting a LAN cable, be sure to use an STP

(shielded) cable.

e RETURN terminals (page 7)

Connect to the output terminal of an external effector. When the [L

(MONO)] channel only is connected, the [L (MONO)] channel input

is simultaneously input to the [R] channel.

f SEND terminals (page 7)

Connect to the input terminal of an external effector. When the [L

(MONO)] channel only is connected, a monaural audio signal is

output.

g BOOTH terminals (page 7)

Output terminals for a booth monitor, compatible with balanced or

unbalanced output for a TRS connector.

h REC OUT terminals (page 7)

These are output terminals for recording.

i MASTER2 terminals (page 7)

Connect to a power amplifier, etc.

j MASTER ATT.

Sets the attenuation level of the sound output from the [MASTER1]

and [MASTER2] terminals.

k MASTER1 terminals (page 7)

Connect to a power amplifier, etc.

Be sure to use these as balanced outputs. Be careful not to acci-

dentally insert the power cord of another unit.

l AC IN

Connects to a power outlet using the included power cord. Wait until

all connections between the equipment are completed before con-

necting the power cord.

Be sure to use the included power cord.

WARNING

The short-circuit pin plugs out of the reach of children and infants. If

accidentally swallowed, contact a doctor immediately.

7

En

English

Connecting input terminals

SIGNAL GND

CD

L

R

L

R

PHONOCDLINE

CONTROL

OUT

IN

RL

R

L

RL(MONO) RL(MONO)

COMPUTER 1

COMPUTER 2

LINK

CH 3

CH 1

CH 4 CH 2

CH2CH3CH4 CH1

DIGITAL

SIGNAL GND

CD

1GND

-6dB -3dB 0dB

2HOT

3COLD

CD

L

R

PHONO

POWEROFF

ON

MASTER

ATT.

DIGITAL

CD DIGITAL

L

R

CDLINE

CONTROL

CD DIGITAL

CH 3CH4

MASTER1

MASTER2

REC OUT

BOOTH SENDRETURN

DIGITAL

CH 1CH2

USB

MIDI OUT

TRS

AC IN

Computers

Pioneer DJ players

2

To power outlet

Pioneer DJ players

2

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

rekordbox rekordbox

PRO DJ LINK

1

Digital audio output device

Analog player

Cassette deck, CD player, etc.

(line level output devices)

Analog player

1 For details on PRO DJ LINK, see About PRO DJ LINK on page 14.

Be sure to use an STP (shielded) cable when connecting to a Pioneer DJ player.

2 To use the fader start function, connect a LAN cable or control cord (page 13).

Connecting output terminals

SIGNAL GND

CD

L

R

L

R

PHONOCDLINE

CONTROL

OUT

IN

RL

R

L

RL(MONO) RL(MONO)

COMPUTER 1

COMPUTER 2

LINK

CH 3

CH 1

CH 4CH 2

CH2CH3CH4CH1

DIGITAL

SIGNAL GND

CD

1GND

-6dB -3dB 0dB

2HOT

3COLD

CD

L

R

PHONO

POWEROFF

ON

MASTER

ATT.

DIGITAL

CD DIGITAL

L

R

CDLINE

CONTROL

CD DIGITAL

CH 3CH 4

MASTER1

MASTER2

REC OUT

BOOTHSENDRETURN

DIGITAL

CH 1CH 2

USB

MIDI OUT

TRS

AC IN

L

R

L

R

Power amplifier

23

To power outlet Power amplifier

(for booth monitor)

External effector

1

MIDI sequencer

Cassette deck, etc.

(analog input recording device)

Power amplifier

Digital audio

input device

1 Also connect the external effector to the [RETURN] terminal (input terminal).

2 Be sure to use the [MASTER1] terminals only for a balanced output (page 31).

3 Be careful not to accidentally insert the power cord of another unit to [MASTER1] terminal.

8

En

Connecting to the control panel

HEADPHONES

CUE

MONO SPLIT STEREO

-

0

CUE

MASTER

PHONES

LEVEL

MIXING

10

9

7

8

6

5

4

3

2

1

0

AB

THRU

A

CROSS FADER ASS

CD

/DIGITALPHONO

USB 1/2

TRIM

MIC

OVER

10

7

4

2

1

0

- 1

- 2

- 3

- 5

- 7

ISO

EQ/

EQ

MID

HI

+

9

+

6

LOW

HI

-26/

+

6

-26/

-12

+12

OFFON OVER

TALK

MIC

LEVEL

0

-

-12

+12

CD

/DIGITAL

ISO

EQ/

-26

Microphones

Headphones

Connecting a computer

SIGNAL GND

CD

L

R

L

R

PHONOCDLINE

CONTROL

O

NO)

COMPUTER 1

COMPUTER 2

LINK

CH 3

CH 1

CH 4CH 2

DIGITALCD DIGITAL

CH 1CH2

MIDI OUT

USB

Computer

Connect with the included USB cable.

About the USB audio driver

software

This driver software is a proprietary program for inputting and output-

ting audio signals from the computer. To use this unit connected to a

computer on which a Windows or Mac OS is installed, install the driver

software on the computer beforehand.

Software end user license agreement

This Software End User License Agreement (“Agreement”) is between

you (both the individual installing the Program and any single legal

entity for which the individual is acting) (“You” or “Your”) and PIONEER

CORPORATION (“Pioneer”).

TAKING ANY STEP TO SET UP OR INSTALL THE PROGRAM MEANS

THAT YOU ACCEPT ALL OF THE TERMS OF THIS LICENSE AGREEMENT.

PERMISSION TO DOWNLOAD AND/OR USE THE PROGRAM IS

EXPRESSLY CONDITIONED ON YOUR FOLLOWING THESE TERMS.

WRITTEN OR ELECTRONIC APPROVAL IS NOT REQUIRED TO MAKE

THIS AGREEMENT VALID AND ENFORCEABLE. IF YOU DO NOT

AGREE TO ALL OF THE TERMS OF THIS AGREEMENT, YOU ARE NOT

AUTHORIZED TO USE THE PROGRAM AND MUST STOP INSTALLING IT

OR UNINSTALL IT, AS APPLICABLE.

1 DEFINITIONS

1 “Documentation” means written documentation, specifications

and help content made generally available by Pioneer to aid in

installing and using the Program.

2 “Program” means all or any part of Pioneer’s software licensed to

You by Pioneer under this Agreement.

2 PROGRAM LICENSE

1 Limited License. Subject to this Agreement’s restrictions,

Pioneer grants to You a limited, non-exclusive, non-transferable,

license (without the right to sublicense):

a To install a single copy of the Program in Your computer or

mobile device, to use the Program only for Your personal pur-

pose complying with this Agreement and the Documentation

(“Authorized Use”);

b To use the Documentation in support of Your Authorized Use;

and

c To make one copy of the Program solely for backup pur-

poses, provided that all titles and trademark, copyright and

restricted rights notices are reproduced on the copy.

2 Restrictions. You will not copy or use the Program or

Documentation except as expressly permitted by this Agreement.

You will not transfer, sublicense, rent, lease or lend the Program,

or use it for third-party training, commercial time-sharing or

service bureau use. You will not Yourself or through any third

party modify, reverse engineer, disassemble or decompile the

Program, except to the extent expressly permitted by applicable

law, and then only after You have notified Pioneer in writing of

Your intended activities.

3 Ownership. Pioneer or its licensor retains all right, title and

interest in and to all patent, copyright, trademark, trade secret

and other intellectual property rights in the Program and

Documentation, and any derivative works thereof. You do not

acquire any other rights, express or implied, beyond the limited

license set forth in this Agreement.

4 No Support. Pioneer has no obligation to provide support,

maintenance, upgrades, modifications or new releases for the

Program or Documentation under this Agreement.

3 WARRANTY DISCLAIMER

THE PROGRAM AND DOCUMENTATION ARE PROVIDED “AS IS”

WITHOUT ANY REPRESENTATIONS OR WARRANTIES, AND YOU

AGREE TO USE THEM AT YOUR SOLE RISK. TO THE FULLEST EXTENT

PERMISSIBLE BY LAW, PIONEER EXPRESSLY DISCLAIMS ALL

WARRANTIES OF ANY KIND WITH RESPECT TO THE PROGRAM AND

DOCUMENTATION, WHETHER EXPRESS, IMPLIED, STATUTORY,

OR ARISING OUT OF COURSE OF PERFORMANCE, COURSE OF

DEALING OR USAGE OF TRADE, INCLUDING ANY WARRANTIES

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,

SATISFACTORY QUALITY, ACCURACY, TITLE OR NON-INFRINGEMENT.

9

En

English

4 DAMAGES AND REMEDIES FOR BREACH

You agree that any breach of this Agreement’s restrictions would cause

Pioneer irreparable harm for which money damages alone would be

inadequate. In addition to damages and any other remedies to which

Pioneer may be entitled, You agree that Pioneer may seek injunctive

relief to prevent the actual, threatened or continued breach of this

Agreement.

5 TERMINATION

Pioneer may terminate this Agreement at any time upon Your breach

of any provision. If this Agreement is terminated, You will stop using

the Program, permanently delete it from your computer or mobile

device where it resides, and destroy all copies of the Program and

Documentation in Your possession, confirming to Pioneer in writing

that You have done so. Sections 2.2, 2.3, 2.4, 3, 4, 5 and 6 will continue in

effect after this Agreement’s termination.

6 GENERAL TERMS

1 Limitation of Liability. In no event will Pioneer or its subsidiaries

be liable in connection with this Agreement or its subject matter,

under any theory of liability, for any indirect, incidental, special,

consequential or punitive damages, or damages for lost profits,

revenue, business, savings, data, use, or cost of substitute pro-

curement, even if advised of the possibility of such damages or if

such damages are foreseeable. In no event will Pioneer’s liability

for all damages exceed the amounts actually paid by You to

Pioneer or its subsidiaries for the Program. The parties acknowl-

edge that the liability limits and risk allocation in this Agreement

are reflected in the Program price and are essential elements of

the bargain between the parties, without which Pioneer would

not have provided the Program or entered into this Agreement.

2 The limitations or exclusions of warranties and liability contained

in this Agreement do not affect or prejudice Your statutory rights

as consumer and shall apply to You only to the extent such limita-

tions or exclusions are permitted under the laws of the jurisdic-

tion where You are located.

3 Severability and Waiver. If any provision of this Agreement is held

to be illegal, invalid or otherwise unenforceable, that provision

will be enforced to the extent possible or, if incapable of enforce-

ment, deemed to be severed and deleted from this Agreement,

and the remainder will continue in full force and effect. The

waiver by either party of any default or breach of this Agreement

will not waive any other or subsequent default or breach.

4 No Assignment. You may not assign, sell, transfer, delegate or

otherwise dispose of this Agreement or any rights or obligations

under it, whether voluntarily or involuntarily, by operation of law

or otherwise, without Pioneer’s prior written consent. Any pur-

ported assignment, transfer or delegation by You will be null and

void. Subject to the foregoing, this Agreement will be binding

upon and will inure to the benefit of the parties and their respec-

tive successors and assigns.

5 Entire Agreement. This Agreement constitutes the entire agree-

ment between the parties and supersedes all prior or contem-

poraneous agreements or representations, whether written or

oral, concerning its subject matter. This Agreement may not be

modified or amended without Pioneer’s prior and express written

consent, and no other act, document, usage or custom will be

deemed to amend or modify this Agreement.

6 You agree that this Agreement shall be governed and construed

by and under the laws of Japan.

Cautions on Installation

! Before installing the driver software, be sure to turn off the power of

this unit and disconnect the USB cable from both this unit and your

computer.

! If you connect this unit to your computer without installing the driver

software first, an error may occur on your computer depending on

the system environment.

! If you have discontinued the installation process in progress, step

through the installation process again from the beginning according

to the following procedure.

! Read Software end user license agreement carefully before installing

this unit’s proprietary driver software.

! Before installing the driver software, terminate all other programs

running on your computer.

! The driver software is compatible with the following OSs.

Supported operating systems

Mac OS X (10.3.9, 10.4, 10.5, 10.6, 10.7, 10.8)

1

Windows

®

7 Home Premium/Professional/

Ultimate

32-bit version

1

64-bit version

1

Windows Vista

®

Home Basic/Home Premium/

Business/Ultimate

32-bit version

1

64-bit version

1

Windows

®

XP Home Edition/Professional (SP2

or later)

32-bit version

1

Windows

®

XP Professional x64 Edition is not supported.

! The included CD-ROM includes installation programs in the follow-

ing 12 languages.

English, French, German, Italian, Dutch, Spanish, Portuguese,

Russian, Simplified Chinese, Traditional Chinese, Korean, and

Japanese

When using operating systems in other languages, follow the

instructions on the screen to select [English (English)].

Installing the driver software

 Installation Procedure (Windows)

Read Cautions on Installation carefully before installing the driver

software.

! To install or uninstall the driver software, you need to be authorized

by the administrator of your computer. Log on as the administrator of

your computer before proceeding with the installation.

1 Insert the included CD-ROM into the computer’s CD

drive.

The CD-ROM folder appears.

! If the CD-ROM folder is not displayed after a CD-ROM is loaded,

open the CD drive from [Computer (or My Computer)] in the [Start]

menu.

2 Double-click [DJM-2000_X.XXX.exe].

The driver installation screen appears.

3 When the language selection screen appears, select

[English] and click [OK].

You can select one from multiple languages depending on the system

environment of your computer.

4 Carefully read the Software end user license

agreement and if you consent to the provisions, put a

check mark in [I agree.] and click [OK].

If you do not consent to the provisions of the Software end user license

agreement, click [Cancel] and stop installation.

5 Proceed with installation according to the instructions

on the screen.

If [Windows Security] appears on the screen while the installation is

in progress, click [Install this driver software anyway] and continue

with the installation.

! When installing on Windows XP

If [Hardware Installation] appears on the screen while the installa-

tion is in progress, click [Continue Anyway] and continue with the

installation.

! When the installation program is completed, a completion message

appears.

! When the installation of the driver software is completed, you need to

reboot your computer.

 Installation Procedure (Macintosh)

Read Cautions on Installation carefully before installing the driver

software.

! To install or uninstall the driver software, you need to be authorized

by the administrator of your computer. Have the name and password

of the administrator of your computer ready in advance.

10

En

1 Insert the included CD-ROM into the computer’s CD

drive.

The CD-ROM folder appears.

! Double-click the CD icon on the desktop when folders are not dis-

played after a CD-ROM has been loaded.

2 Double-click [DJM-2000_M_X.X.X.dmg].

The [DJM-2000AudioDriver] menu screen appears.

3 Double-click [DJM-2000AudioDriver.pkg].

The driver installation screen appears.

4 Check the details on the screen and click [Continue

Anyway].

5 When the Software Use Agreement screen appears,

select [English], carefully read the Software end user

license agreement and click [Continue Anyway].

You can select one from multiple languages depending on the system

environment of your computer.

6 If you consent to the provisions of the Software end

user license agreement, click [Agree].

If you do not consent to the provisions of the Software end user license

agreement, click [I disagree] and stop installation.

7 Proceed with installation according to the instructions

on the screen.

! Click [Cancel] to cancel installation after it has started.

! When the installation of the driver software is completed, you need to

reboot your computer.

Connecting this unit and computer

1 Connect this unit to your computer via a USB cable.

This unit functions as an audio device conforming to the ASIO

standards.

! When using ASIO-compatible applications, [USB 1/2], [USB 3/4],

[USB 5/6] and [USB 7/8] can be used as inputs. Depending on the

input/output setting, it is possible to use three of this unit’s sets of

inputs.

! When using DirectX-compatible applications, only [USB 1/2] can be

used as the input.

! The computer’s recommended operating environment depends on

the DJ application. Be sure to check the recommended operating

environment for the DJ application you are using.

! When another USB audio device is connected to the computer at the

same time, it may not operate or be recognized normally.

We recommend only connecting the computer and this unit.

! When connecting the computer and this unit, we recommend con-

necting directly to this unit’s USB port.

2 Press [POWER] button.

Turn on the power of this unit.

! The message [Installing device driver software] may appear when

this unit is first connected to the computer or when it is connected to

a different USB port on the computer. Wait a while until the message

[Your devices are ready for use] appears.

! When installing on Windows XP

— [Can Windows connect to Windows Update to search for

software?] may appear while the installation is in progress.

Select [No, not this time], then click [Next] to continue

installation.

— [What do you want the wizard to do?] may appear while

the installation is in progress. Select [Install the software

automatically (Recommended)], then click [Next] to continue

installation.

— If [Windows Security] appears on the screen while the installa-

tion is in progress, click [Install this driver software anyway]

and continue with the installation.

Switching the input/output setting

Use this procedure to switch the computer’s input/output setting when

using the driver software.

! If applications using this unit as the default audio device (DJ applica-

tions, etc.) are running, quit those applications before switching the

input/output setting.

! Some time is required after the input/output setting is switched for

the computer to be updated. The input/output setting cannot be

switched while the computer is being updated.

! Sound may not be output if there are differences between the input/

output settings on this unit and on the computer. If this happens,

turn this unit’s power on and reset the input/output settings with the

USB cable connected.

! If the input/output setting is switched while using DirectX, the appli-

cation may not recognize the driver software.

! MIDI communications are interrupted if the input/output setting is

switched during MIDI communications.

 Switching procedure (Windows)

Click the Windows [Start] menu>[All

Programs]>[Pioneer]>[DJM-2000]>[DJM-2000 Setting

Utility].

Switch the computer’s input/output setting.

— ASIO 4 outputs 0 inputs 16 bits DirectX 1 output 0 inputs

— ASIO 3 outputs 1 input 16 bits DirectX 1 output 1 input

— ASIO 3 outputs 0 inputs 24 bits DirectX 1 output 0 inputs

 Switching procedure (Macintosh)

Click [Apple]>[System Preferences]>[Other]>[DJM-2000

Settings].

Switch the computer’s input/output setting.

— 8-channel output No input 16 bits

— 6-channel output 2-channel input 16 bits

— 6-channel output No input 24 bits

Adjusting the buffer size (Windows)

Use this procedure to adjust the computer’s buffer size when using

ASIO driver software.

Click the Windows [Start] menu>[All

Programs]>[Pioneer]>[DJM-2000]>[DJM-2000 Setting

Utility].

If the buffer size is made large, drops in audio data (breaks in the sound)

occur less easily, but the time lag due to the delay in the transfer of the

audio data (latency) increases.

! If an application using this unit as the default audio device (DJ

software, etc.) is running, quit that application before adjusting the

buffer size.

Checking the version of the driver

software

 Procedure for checking (Windows)

Click the Windows [Start] menu>[All

Programs]>[Pioneer]>[DJM-2000]>[DJM-2000 Version

Display Utility].

The [Version] screen appears.

 Procedure for checking (Macintosh)

Click [Apple]>[About This Mac]>[More

Info]>[Extensions]>[DJM-2000 USBAudio].

The [Version] screen appears.

Checking the latest information on the

driver software

For the latest information on the driver software for exclusive use with

this unit, visit our website shown below.

http://pioneerdj.com/support/

11

En

English

Operation

Control Panel

OVER

POWER

CD

/DIGITAL PHONO

USB 1/2

TRIM

CH

SELECT

EFFECT SELECT

EFFECT FREQUENCY

1 2 3 4

OFF

ON

MASTER

LINK

HEADPHONES

MIC

INST FX

MIDI

CURVE SETTING

10

7

4

2

1

0

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

dB

10

9

7

8

6

5

4

3

2

1

0

BALANCE

LOW

TIME

LIVE

SAMPLER

WAKE UP

LEVEL/DEPTH

1/8

1/4 1/2 3/4 1/1 2/1 4/1

MIN MAX

MIN

MAX

AUTO

/TAP

TAP

ON/OFF

CUE

AB

DELAY

ECHO

FILTER

GATE

ROLL

TRANS

REVERB

MULTI TA P

DELAY

PHASER

SLIP

ROLL

SEND/

RETURN

REV

ROLL

CUE

NOISEJET

ZIPHPF

CRUSHLPF

MONO

ON/OFF

CH EQ

EQ

CROSS FADER

CH FADER

ISOLATOR

START/STOP

SNAPSHOT

UTILITY

BOOTH MONITOR

STEREO

MONO SPLIT STEREO

LR

DJM-

2000 nexus

-

0

L

R

FILTER

PARAMETER

MIN MAX

OVER

10

7

4

2

1

0

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

dB

ISO

EQ/

EQ

LOW

MID

HI

+

9

+

6

-

0

LOW

MIN

MAX

CUE

MASTER

PHONES

LEVEL

MIXING

HI

-26/

+

6

-26/

+

6

-26/

-12

+12

OFF ON OVER

TALK

PROFESSIONAL MIXER

10

9

7

8

6

5

4

3

2

1

0

AB

THRU

AB

THRU

CROSS FADER ASSIGN

AB

THRU

AB

THRU

CROSS FADER ASSIGN

MIC

LEVEL

0

-

CUE

FILTER

MIN MAX

CUE

FILTER

MINMAX

CUE

FILTER

MINMAX

-12

+12

CD

/DIGITAL LINE

USB 3/4

OVER

10

7

4

2

1

0

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

dB

10

7

4

2

1

0

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

dB

ISO

EQ/

ISO

EQ/

TRIM

+

9

HI

+

6

-26/

MID

+

6

-26/

LOW

+

6

-26/

CD

/DIGITAL LINE

USB 5/6

TRIM

+

9

HI

+

6

-26/

MID

+

6

-26/

LOW

+

6

-26/

OVER

10

7

4

2

1

0

- 1

- 2

- 3

- 5

- 7

- 10

- 15

- 24

dB

ISO

EQ/

CD

/DIGITAL PHONO

USB 7/8

TRIM

+

9

HI

+

6

-26/

MID

+

6

-26/

LOW

+

6

-26/

OVER

MIC

A B M

MID

MINMAX

HI

MINMAX

MIX

REMIX

3

2

4

6

8

9

a

b

7

1

d

f

g

7

h

i

c

5

e e ee

d

f

g

7

h

i

c

n

r

w

q

o

x

7

s

d

f

g

7

h

i

c

d

f

g

7

h

i

c

y

A

B

C

D

F

G

H

E

7

z

j

m

k

l

v

u

p

t

1 Microphone input jack (page 13)

2 MIC LEVEL control (page 13)

3 EQ (HI, LOW) controls (page 13)

4 OFF, ON, TALK OVER selector switch (page 13)

5 INST FX buttons (page 18)

6 PARAMETER control (page 18)

7 CUE button (page 12)

8 MONO SPLIT, STEREO selector switch (page 12)

9 MIXING control (page 12)

a LEVEL control (page 12)

b PHONES terminal (page 12)

c CD/DIGITAL, PHONO, LINE, USB */* selector switch

(page 12)

d TRIM control (page 12)

e EQ/ISO (HI, MID, LOW) controls (page 12)

f Channel Level Indicator (page 12)

g FILTER control (page 18)

h Channel Fader (page 12)

i CROSS FADER ASSIGN (A, THRU, B) selector switch

(page 12)

j CH SELECT buttons (page 18)

k EFFECT SELECT buttons (page 18)

l EFFECT FREQUENCY (HI, MID, LOW) controls (page 18)

m Beat buttons (page 18)

n TIME control (page 18)

o LEVEL/DEPTH control (page 18)

p AUTO/TAP button (page 18)

q TAP button (page 18)

12

En

r ON/OFF button (page 18)

s LIVE SAMPLER (UTILITY, WAKE UP) buttons (page 17,

page 27)

t SYNC MASTER/MIDI button (page 19)

u MIX button (page 15)

v REMIX button (page 16)

w ON/OFF button (TOUCH PANEL EFFECT) (page 15)

x Crossfader (page 12)

y MASTER control (page 12)

z Master Level Indicator (page 12)

A BALANCE control (page 14)

B MONO, STEREO selector switch (page 14)

C BOOTH MONITOR control (page 14)

D START/STOP (SNAPSHOT) button (page 19)

E ON/OFF (MIDI) button (page 19)

F CH EQ (ISOLATOR, EQ) selector switch (page 12)

G CH FADER (

, ) selector switch (page 13)

H CROSS FADER (

, , ) selector switch (page 13)

Do not pull on the channel fader and crossfader knobs with excessive

force. The knobs have a structure by which they cannot be pulled off

easily. Pulling the knobs strongly may result in damaging the unit.

Basic Operation

Outputting sound

1 Press [POWER] button.

Turn on the power of this unit.

2 Switching the [CD/DIGITAL, PHONO, LINE, USB */*]

switch

Selects the input sources for the different channels from among the

devices connected to this unit.

— [CD/DIGITAL]: Selects the DJ player connected to the [CD] termi-

nals. To select the DJ player connected to the [DIGITAL IN] termi-

nal, set the [CD, DIGITAL] switch on the rear panel to [DIGITAL].

— [PHONO]: Selects the analog player connected to the [PHONO]

terminals.

— [LINE]: Selects the cassette deck or CD player connected to the

[LINE] terminals.

— [USB */*]: Selects the sound of the computer connected to the

[USB] port.

3 Turn the [TRIM] control.

Adjusts the level of audio signals input in each channel.

The corresponding channel level indicator lights when audio signals are

being properly input to that channel.

4 Move the channel fader away from you.

Adjusts the level of audio signals output in each channel.

5 Switch the [CROSS FADER ASSIGN (A, THRU, B)]

switch.

Switches the output destination of each channel.

— [A]: Assigns to [A] (left) of the crossfader.

— [B]: Assigns to [B] (right) of the crossfader.

— [THRU]: Selects this when you do not want to use the crossfader.

(The signals do not pass through the crossfader.)

6 Set the crossfader.

This operation is not necessary when the [CROSS FADER ASSIGN (A,

THRU, B)] selector switch is set to [THRU].

7 Turn the [MASTER] control.

Audio signals are output from the [MASTER1] and [MASTER2]

terminals.

The master level indicator lights.

Adjusting the sound quality

Turn the [EQ/ISO (HI, MID, LOW)] controls for the

respective channels.

Refer to Specifications on page 31 for the range of sound that can be

adjusted by each control.

 Switching the function of the [EQ/ISO (HI, MID,

LOW)] controls

Switch the [CH EQ (ISOLATOR, EQ)] selector switch.

— [ISOLATOR]: The isolator function is set. The indicator lights.

— [EQ]: The equalizer function is set.

Monitoring sound with headphones

1 Connect headphones to the [PHONES] terminal.

2 Press the [CUE] button(s) for the channel(s) you want

to monitor.

13

En

English

3 Switch the [MONO SPLIT, STEREO] selector switch.

— [MONO SPLIT]: The sound of the channels for which the [CUE]

button is pressed is output from the headphones output’s left

channel, the [MASTER] channel sound is output from the right

channel.

— [STEREO]: The sound of the channels for which the [CUE] button

is pressed is output from the headphones in stereo.

4 Turn the [MIXING] control.

This adjusts the monitor volume balance of the sound of channels for

which the [CUE] button is pressed and the sound of the [MASTER]

channel.

5 Turn the [LEVEL] control for [HEADPHONES].

The sound of the channels for which the [CUE] button is pressed is

output from the headphones.

! When the [CUE] button is pressed again, monitoring is canceled.

! When [LIVE SAMPLER] is turned on, [CUE] button for the TOUCH

PANEL EFFECT and [CUE] button for the [LINK] cannot be pressed

simultaneously.

Monitoring the sound of the computer

Check [Use “LINK MONITOR” of Pioneer DJ Mixers.] at [File] >

[Preferences] > [Audio] in rekordbox beforehand. Also refer to the

rekordbox operating instructions.

1 Connect headphones to the [PHONES] terminal.

2 Connect a computer on which rekordbox is installed.

For instructions on connections, see Connecting input terminals on page

7.

3 Selecting the track to be monitored with rekordbox.

4 Press the [CUE] button for [LINK].

The track selected with rekordbox is output from the headphones.

! When the [CUE] button is pressed again, monitoring is canceled.

! The same operation as at Monitoring sound with headphones (steps 3

to 5) can be performed.

Switching the fader curve

 Select the channel fader curve characteristics.

Switch the [CH FADER (

, )] switch.

— [ ]: The curve rises suddenly at the back side.

— [ ]: The curve rises gradually (the sound gradually increases as

the channel fader is moved away from the front side).

 Select the crossfader curve characteristics.

Switch the [CROSS FADER (

, , )] selector switch.

— [ ]: Makes a sharply increasing curve (if the crossfader is

moved away from the [A] side, audio signals are immediately

output from the [B] side).

— [

]: Makes a curve shaped between the two curves above and

below.

— [ ]: Makes a gradually increasing curve (if the crossfader is

moved away from the [A] side, the sound on the [B] side gradu-

ally increases, while the sound on the [A] gradually decreases).

Starting playback on a DJ player using

the fader (fader start)

When connected to a Pioneer DJ player by LAN cable or control cord

(included with the DJ player), operations such as starting playback on

the DJ player can be controlled with this unit’s fader.

Connect this unit and Pioneer DJ player beforehand. For instructions on

connections, see Connecting input terminals on page 7.

 Start playback using the channel fader

1 Set the [CROSS FADER ASSIGN (A, THRU, B)] selector

switch to [THRU].

2 Set [FADER START] to [ON].

For instructions on setting, see Changing the settings on page 27.

3 Set the channel fader to the nearest position towards

you.

4 Set the cue on the DJ player.

The DJ player pauses playback at the cue point.

5 Move the channel fader away from you.

Playback starts on the DJ player.

! If you set the channel fader back to the original position, the player

instantaneously returns to the cue point already set and pauses

playback (back cue).

 Start playback using the crossfader

1 Set the [CROSS FADER ASSIGN (A, THRU, B)] selector

switch to [A] or [B].

2 Set [FADER START] to [ON].

For instructions on setting, see Changing the settings on page 27.

3 Set the crossfader.

Set to the edge opposite the side on which the channel you want to use

with the fader start function is set.

4 Set the cue on the DJ player.

The DJ player pauses playback at the cue point.

5 Set the crossfader.

Playback starts on the DJ player.

! If you set the crossfader back to the original position, the player

instantaneously returns to the cue point already set and pauses

playback (back cue).

Using a microphone

1 Connect the microphone to the microphone input

jack.

2 Set the [OFF, ON, TALK OVER] selector switch to [ON]

or [TALK OVER].

— [ON]: The indicator lights.

— [TALK OVER]: The indicator flashes.

! When set to [TALK OVER], the sound of channels other than the

[MIC] channel is attenuated by 18 dB (default) when a sound of -10

dB or greater is input to the microphone.

3 Turn the [MIC LEVEL] control.

Adjust the level of the sound output from the [MIC] channel.

! Pay attention that rotating to the extreme right position outputs a

very loud sound.

4 Input audio signals to the microphone.

 Adjusting the sound quality

Turn the [MIC] channels’ [EQ (HI, LOW)] controls.

Refer to Specifications on page 31 for the range of sound that can be

adjusted by each control.

14

En

Switching between monaural and stereo

audio

This switches the sound output from the [MASTER1], [MASTER2],

[BOOTH], [REC OUT], [PHONES], [DIGITAL OUT] and [USB] terminals

between monaural and stereo.

Switch the [MONO, STEREO] selector switch.

— [MONO]: Outputs monaural audio.

— [STEREO]: Outputs stereo audio.

 Adjusting the L/R balance of audio

The left/right balance of the sound output from the [MASTER1],

[MASTER2], [BOOTH], [REC OUT], [PHONES], [DIGITAL OUT] and

[USB] terminals can be adjusted.

1 Set the [MONO, STEREO] selector switch to [STEREO].

2 Turn the [BALANCE] control.

The sound’s left/right balance changes according to the direction in

which the [BALANCE] control is turned and its position.

! Rotating to the rightmost position outputs only the right sound of

stereo audio. Rotating to the leftmost position outputs only the left

sound of stereo audio.

Audio is output from the [BOOTH]

terminal

Turn the [BOOTH MONITOR] control.

Adjusts the level of audio signals output from the [BOOTH] terminal.

Advanced Operations

About PRO DJ LINK

When a PRO DJ LINK-compatible Pioneer DJ player (CDJ-2000, CDJ-900

etc.), a computer on which rekordbox is installed and this unit are con-

nected by LAN cable, the PRO DJ LINK functions below can be used.

For more details on the PRO DJ LINK function, also refer to the DJ play-

er’s handling instructions and rekordbox’s operating instructions.

For instructions on connections, see Connecting input terminals on page

7.

! Up to four DJ players can be connected. Up to two computers can be

connected.

! Connect the DJ players to the [LINK] terminal ([CH1] to [CH4]) with

the same number as the channel to which the audio cables are

connected.

! Connect the computers to the [COMPUTER 1] or [COMPUTER 2]

terminal.

 SD & USB Export

rekordbox music files and management data on an SD memory card or

USB device connected to a Pioneer DJ player supporting PRO DJ LINK

(e.g. CDJ-2000nexus, CDJ-2000, CDJ-900) can be transferred between DJ

players via this unit.

 rekordbox LINK Export

This function lets you transfer rekordbox music files and management

data directly, eliminating the bother of exporting the data to an SD

memory card/USB device.

 SYNC MASTER

The beats (tempos and beat positions) of CDJ-2000nexus tracks can be

played in sync with this unit’s master clock for up to four units. The beats

of the tracks can be managed collectively on the mixer, allowing you to

concentrate on the performance (mixing, effects, etc.).

 LIVE SAMPLER

The sound input to the [MIC] terminal or output from the [MASTER]

terminals can be sampled and played on a DJ player.

 LINK MONITOR

With this function, rekordbox music files stored on the computer can be

quickly monitored over the headphones.

 STATUS INFORMATION

This function informs the DJ players of the connected channel status

(on-air status, channel number, etc.).

 QUANTIZE function

Based on the GRID information of tracks that have been analyzed with

rekordbox, effects can be added to the sound without getting out of

tempo with the currently playing track.

QUANTIZE

Music files must be analyzed ahead of time with rekordbox in order to

use the QUANTIZE function. For instructions on analyzing music files

with rekordbox, see the rekordbox Operating Instructions.

! The QUANTIZE function cannot be used when [REVERB], [GATE] or

[SEND/RETURN] is selected.

! To use the QUANTIZE function, set the BPM measurement mode to

AUTO.

! Before using in combination with a CDJ-2000 or CDJ-900, update the

DJ player’s firmware to version 4.0 or later.

15

En

English

1 Press [LIVE SAMPLER (UTILITY, WAKE UP)] for at least

1 seconds.

The [USER SETUP] screen is displayed.

2 Press the settings item button and select [QUANTIZE].

The QUANTIZE function’s setting screen is displayed.

! [QUANTIZE] is added to the settings item button on the

[USER SET UP] screen.

3 Press [ON].

The QUANTIZE function turns on.

The QUANTIZE indicator ([QTZ]) and GRID indicator ([GRID]) on the

main unit display light or flash.

! Depending on the status of the DJ player (off air, scratching, reverse

playing, etc.), it may not be possible to receive the GRID information.

QUANTIZE indicator

GRID indicator

About the QUANTIZE indicator’s lighting status

[USER SET

UP] screen >

[QUANTIZE]

QUANTIZE function status [QTZ]

[ON]

QUANTIZE function activated (effects

synchronized to track’s tempo).

Lit

QUANTIZE function not activated (effects

not synchronized to track’s tempo, or BPM

measurement mode set to TAP).

Flashes

[OFF] Off

About the GRID indicator’s lighting status

Status of reception of grid information from DJ player [GRID]

GRID information being received. Lit

GRID information not being received. Off

4 Press the beat button, then press the [ON/ OFF]

button of [BEAT EFFECT].

The effect is added to the sound on beat with the tempo of the currently

playing track.

The beat positions and BPMs of tracks being played on Pioneer DJ play-

ers supporting the beat sync function (e.g. CDJ-2000nexus, CDJ-2000,

CDJ-900) can be synchronized.

STATUS INFORMATION

The display of the status of DJ players connected to the different chan-

nels and the beat sync information is concentrated here.

1 2 3 4 5

1

FS

Indicates channels for which the fader start function

is enabled.

2

LINK

Indicates channels for which DJ players are properly

connected to the [LINK] terminal.

3

SYNC

Indicates the sync function status of the DJ player con-

nected to the [LINK] terminal.

4

MASTER

Indicates the current beat sync master.

5

MASTER BPM

Indicates the current master BPM.

FREQUENCY MIX

The currently playing sound is divided into seven frequency bands that

are displayed graphically. Fader control on the touch panel makes it

easier to grasp the details and mix two channels or swap instruments

(parts).

3

4

1

2

1

Channel assign

buttons

These select the channels to be mixed.

2

Volume level

display

The input volume level to this function is displayed in a

light color, the output volume level from this function is

displayed in a dark color.

3

Touch fader

These adjust the volume balance of the channels to be

mixed for the separate frequency bands.

4

<< >>

These move the touch fader immediately to the left or

right edge.

 To mix [CH2] and [CH3]:

Prepare this unit in advance so that the sound of [CH3] is being output

from the [MASTER] terminals.

1 Set the [CROSS FADER ASSIGN (A, THRU, B)] switches

for [CH2] and [CH 3] to [THRU].

! Set the [CROSS FADER ASSIGN (A, THRU, B)] switches of the chan-

nels to be mixed to [THRU].

! When using the crossfader, it is recommended to set it to the center

position.

2 Press [MIX].

The [FREQUENCY MIX] screen appears on the touch panel.

3 Press the channel assign buttons to select [CH2] for

the left side, [CH3] for the right side.

The volume levels for the individual frequency bands of the sound play-

ing in [CH3] are displayed on the right half of the touch panel.

4 Press all the [ >> ] buttons.

All the touch faders move to the right edge.

5 Press the [ON/ OFF] button.

This turns the effect on.

The [ON/ OFF] button flashes when the effect is on.

6 Move the channel fader for [CH2] to the back side.

The volume levels for the individual frequency bands of the sound play-

ing in [CH2] are displayed on the left half of the touch panel.

7 Move the touch fader to the left side.

The sound of the frequency bands whose crossfaders have been moved

is mixed and output.

! When the [ON/ OFF] button is pressed again, the effect turns off.

! To switch from the [FREQUENCY MIX] to the REMIX function, first

press [ON/OFF] to turn the effect off, then press [REMIX].

16

En

BEAT SLICE REMIX

When a track that has been analyzed with rekordbox is played, the sound

is sampled in beat with the track, and once sampling is completed the

sample is played in a loop.

The sampled sound can be sliced into equal parts, and the order in

which the sliced parts are played can be changed.

The changed order and timing can be played repeatedly in units of the

length of the sampled sound (4 or 8 beats).

8

9

a

b

1 72 3 4

6

5

1

Channel select

menu

Used to select the channel to which the sound you

want to sample is being input.

2

SETTING

Displays the settings screen at which various settings

are made.

3

SEQ REC

Records the order and time at which the roll pad is

pressed.

4

MUTE

Inserts a silent section in the rolled sound.

5

ROLL PAD

Rolls the sampled sound that has been sliced into 8

equal parts for the specified length.

6

Sequence control

Displays the waveform of the sampled sound. Playback

can be started from the sound of that waveform by

touching the waveform (cue).

7

EXIT

Exits this screen, returning to the BEAT SLICE REMIX

screen.

8

OUTPUT CH select

Selects the output channel for the beat slice remix

function.

! SAME: Sets the input channel to the output

channel.

! CH1 – 4: Sets the selected channel as the output

channel.

9

SEQUENCE

LENGTH select

Selects the length for sampling the sound.

! 4BEAT: Samples 4 beats of sound.

! 8BEAT: Samples 8 beats of sound.

a

SYNC SOURCE

Selects the beat information to serve as the basis for

the operation.

! CHANNEL: Selects the audio input channel’s beat

information as the basis.

! SYNC MASTER: Selects the master BPM’s beat

information as the basis.

! MANUAL: Selects the BPM and beat position set

at the BPM setting as the basis.

b

BPM setting

When [MANUAL] is selected at SYNC SOURCE, specify

the BPM and beat position to serve as the basis here.

! a/b: Increases or decreases the BPM value.

! BPM display: Displays the BPM value to serve as

the basis for the operation. If the beat information

cannot be obtained, the display flashes.

! TAP: When this button is tapped 2 or more times,

the interval at which it was tapped is calculated

and displayed in the BPM display area as the BPM

value.

1 Press [REMIX].

The [BEAT SLICE REMIX] screen appears on the touch panel.

! The function switches between [BEAT SLICE REMIX] and

[SIDECHAIN REMIX] each time the [REMIX] button is pressed.

2 Press one of the buttons on the channel select menu.

Select the input channel.

3 Press the [ON/ OFF] button (TOUCH PANEL EFFECT).

Sampling of the sound starts.

Once the sound is sampled for the number of beats specified at

[SEQUENCE LENGTH], rolling of that sound starts.

! The sampled sound is sliced into equal parts based on the beat posi-

tion information obtained by PRO DJ LINK or the beat time calcu-

lated from the BPM value and the parts are assigned to the roll pad

for the respective beat lengths to be played.

4 Press the roll pad.

The assigned sound is played.

If the roll pad is pressed and held for a time longer than the assigned

sound, the assigned sound is played repeatedly.

SIDECHAIN REMIX

When this function is used, the sound of the specified frequency band

for the specified channel can be used as the trigger to apply effects to

the sounds of other channels.

5

3

4

7

9

a

8

2

1

6

1

CH

This selects the channel to which the effect is applied.

2

HOLD

This holds the effect’s parameter information (the posi-

tion at which the control area was touched).

3

EFFECT

This selects the type of effect.

4

LEVEL/DEPTH

Use this to adjust the amount of the effect applied.

5

EXIT

Use this to close the [TRIGGER] menu.

6

TRIGGER

(SAMPLING/

TRIGGER)

Use this to open the [TRIGGER] menu.

7

TRIGGER BAND

Use these to select the frequency band to be used as

the trigger.

8

Control area Use this to change the effect’s parameters.

9

TRIGGER CH

(SAMPLING/

TRIGGER CH)

This selects the channel to be used as the effect

trigger.

a

Trigger indicators

These flash according to the automatically detected

rhythm for the different frequency bands.

 To set the channel for sampling and triggering

to [CH3] and mix the sampled sound with the

sound of [CH2] for output:

Prepare this unit in advance so that the sound of [CH2] is being output

from the [MASTER] terminals.

1 Press [REMIX] twice.

The [SIDECHAIN REMIX] screen appears on the touch panel.

2 Press the [2] button in the [CH] section.

This selects the channel to which the effect is applied.

3 Press [EFFECT] and select [SAMPLER].

This selects the type of effect.

17

En

English

Effect Name Descriptions

NOISE

HI-HAT

CLAP

SNARE

Sound is created inside this unit, mixed to the sound

of the channel selected in the [CH] section, then

output according to the [TRIGGER CH (SAMPLING/

TRIGGER CH)] trigger.

SAMPLER

The sound of the channel selected at [TRIGGER CH

(SAMPLING/TRIGGER CH)] is sampled, mixed to

the sound of the channel selected in the [CH] sec-

tion, then output according to the [TRIGGER CH

(SAMPLING/TRIGGER CH)] trigger.

PITCH

The pitch of the sound of the channel selected in

the [CH] section is changed, mixed with the channel

selected in the [CH] section, then output according

to the [TRIGGER CH (SAMPLING/TRIGGER CH)]

trigger.

GATE

The sound input at [CH] is output according to the

[TRIGGER CH (SAMPLING/TRIGGER CH)] trigger.

! It is not possible to select multiple effects simultaneously.

4 Press [TRIGGER (SAMPLING/TRIGGER)].

The [TRIGGER] menu appears.

5 At [TRIGGER CH (SAMPLING/TRIGGER CH)], select

[CH3].

This selects the channel to be used as the effect trigger.

! When [SAME] is pressed, the same channel as the one selected in

the [CH] section is selected as the trigger.

6 At [TRIGGER BAND], press [MID] and [HI].

This selects the frequency band set as the effect trigger.

Only [LOW] (the bass sound) is selected.

7 Press the [ON/ OFF] button.

This turns the effect on.

The [ON/ OFF] button flashes when the effect is on.

8 Touch the control area.

[ ] appears at the point at which the panel was touched.

The [CH3] sound at the point in the control area that was touched is

sampled.

Triggered by the low frequency sound of [CH3], the sampled sound is

mixed with the sound of [CH2] (which is continuing to play normally) and

output from the [MASTER] terminals.

The effect changes when the position touched in the control area is

changed.

! When the [ON/ OFF] button is pressed again, the effect turns off.

! The sampled sound is only valid while the control area is being

touched.

! To switch from the [SIDECHAIN REMIX] to the [FREQUENCY MIX]

mode, first press the [ON/OFF] button to turn the effect off, then

press [MIX].

 Using [HOLD]

When [HOLD] is turned on, effect’s parameter information is held even

if the effect is turned off. The parameter information is cleared when

[HOLD] is turned off.

! The parameter information and sampled sound are cleared when the

effect is switched.

LIVE SAMPLER

The sound input to the [MIC] terminal or the sound output from the

[MASTER] terminals can be sampled and played on a PRO DJ LINK–

compatible Pioneer DJ player.

Connect this unit and PRO DJ LINK-compatible Pioneer DJ player in

advance. For instructions on connections, see Connecting input termi-

nals on page 7.

1

2

3

7

8

9

4

5

6

1

SOURCE SELECT

Select the source to be sampled here.

2

REC VOLUME

Use these to adjust the volume for recording.

The volume can be adjusted in the range –9 dB to +9

dB.

3

Status indicator

This indicates this unit’s status and whether or not

sampling data is available.

4

Waveform display This displays the sound as a waveform.

5

Playing address

display

This displays the sound as a bar graph.

This is only displayed when previewing the sound.

6

Slider

The sound is played from the position at which the

touch panel was touched.

This is only displayed when previewing the sound.

7

PRE-REC SAVE

The sound is sampled from a point 8 seconds before

the button was pressed.

8

REC (REC STOP)

The sound is sampled for up to 8 seconds from the

point at which the button is pressed.

9

PREVIEW (STOP)

Use this to preview the sampled sound over the

headphones.

 Sampling the sound being played

1 Press [LIVE SAMPLER].

The [LIVE SAMPLER] screen appears on the touch panel.

2 Press [MIC] or [MASTER] in the [SOURCE SELECT].

This selects the channel to be sampled.

3 Press [REC (REC STOP)].

The sound of the channel selected at step 2 is sampled from the point at

which [REC (REC STOP)] was pressed.

! Sampling is possible for up to 8 seconds.

! Sampling stops automatically once 8 seconds have elapsed after

[REC (REC STOP)] was pressed.

4 Press [REC (REC STOP)].

Sampling stops. The sample saving screen is displayed.

 Sampling the sound from the point 8 seconds

before

1 Press [LIVE SAMPLER].

The [LIVE SAMPLER] screen appears on the touch panel.

2 Press [MIC] or [MASTER] in the [SOURCE SELECT].

This selects the channel to be sampled.

3 Press [PRE-REC SAVE].

The sound for the channel selected in step 2 is sampled from the point 8

seconds before [PRE-REC SAVE] was pressed.

! Sampling is possible for up to 8 seconds.

 Previewing the sampled sound

1 Press the [CUE] button to the left of the touch panel.

2 Press [PREVIEW (STOP)].

The position being played is displayed at the playing address and slider

displays.

! When the touch panel’s slider is touched, the sampled sound is

played from that position.

18

En

 Playing the sampled sound on the DJ player

Use PRO DJ LINK to access this unit from the DJ player.

The sampled sound (audio file) can be loaded and played on the DJ

player.

INST FX

This effect changes in association with the [FILTER] controls for the

individual channels.

1 Press one of the [INST FX] buttons.

This selects the type of effect.

The button that was pressed flashes.

! The same effect is set for [CH1] to [CH4].

2 Turn the [FILTER] control.

The effect is applied to the channel(s) for which the control(s) was (were)

pressed.

Effect Name Descriptions

FILTER

(parameter 1)

PARAMETER

(parameter 2)

NOISE

White noise gener-

ated inside this unit

is mixed in to the

sound of the chan-

nel via the filter and

output.

Sets the cut-off

frequency for the

filter through which

the white noise

passes.

Sets the volume of

the white noise.

ZIP

Lowers the pitch of

the channel’s sound

for output.

Sets the amount of

pitch shifting for

lowering the pitch.

Sets the balance

between the origi-

nal sound and the

effect sound.

CRUSH

Changes the chan-

nel’s sound to a

crushed sound for

output.

Sets the degree

by which the input

sound is crushed.

The further the

control is turned

clockwise, the

more the effect is

stressed.

JET

Adds a flanger effect

for output.

Sets the flanger

effect.

The further the

control is turned

clockwise, the

more the effect is

stressed.

HPF

Outputs the sound

through the high-

pass filter.

Sets the filter’s cut-

off frequency.

The further the

control is turned

clockwise, the

more the effect is

stressed.

LPF

Outputs the sound

through the low-

pass filter.

Sets the filter’s cut-

off frequency.

The further the

control is turned

clockwise, the

more the effect is

stressed.

 Adjusting the effect of the effect sound

Turn the [PARAMETER] control.

The further the control is turned clockwise, the more the effect is

stressed. When turned all the way counterclockwise, the effect is

minimum.

BEAT EFFECT

This function lets you instantaneously set various effects according to

the tempo (BPM = Beats Per Minute) of the currently playing track.

1

4

3

2

1

BPM value display

(3 digits)

When in the auto mode, this displays the automatically

detected BPM value.

When the BPM cannot be detected, the previously

detected BPM value is displayed and flashes.

When in the manual input mode, this displays the BPM

value that was input manually.

2

AUTO (TAP)

[AUTO] lights when the BPM measurement mode is

set to the auto mode.

[TAP] lights when in the manual input mode.

3

BPM

This is always lit.

4

% (ms)

These light according to the units for the different

effects.

1 Press [AUTO/TAP] button.

Select the BPM measurement mode.

— [AUTO]: The BPM is measured automatically from the audio sig-

nal that is being input. The [AUTO] mode is set when this unit’s

power is turned on.

— [TAP]: The BPM is input manually by tapping the [TAP] button

with a finger.

! The [AUTO] BPM measurement range is BPM = 70 to 180. With

some tracks it may not be possible to measure the BPM correctly. If

the BPM cannot be measured, the BPM value on the display flashes.

In such cases, use the [TAP] button to input the BPM manually.

2 Press one of the [CH SELECT] buttons.

This selects the channel to which the effect is applied.

— [1] – [4]: The effect is applied to the sound of the respective

channel.

— [MIC]: The effect is applied to the sound of [MIC] channel.

— [A], [B]: The effect is applied to the sound of the crossfader’s [A]

(left) or [B] (right) side.

— [M]: The effect is applied to the sound of the [MASTER] channel.

3 Press one of the [EFFECT SELECT] buttons.

This selects the type of effect.

! For the types of effects, see Types of BEAT EFFECT on page 25.

! To use [SEND/RETURN], see Using the external effector below.

4 Press one of the beat buttons.

Set the beat fraction for synchronizing the effect sound.

The effect time corresponding to the beat fraction is set automatically.

! The beat fraction can be changed by turning [TIME] while pressing

the beat button.

5 Press the [ON/ OFF] button.

The effect is applied to the sound.

The effect’s time parameter can be adjusted by turning the [TIME]

control.

The effect’s quantitative parameter can be adjusted by turning the

[LEVEL/DEPTH] control.

The [ON/ OFF] button flashes when the effect is on.

! When the [ON/ OFF] button is pressed again, the effect turns off.

 Inputting the BPM manually

Tap the [TAP] button at least 2 times in rhythm with the

beat (in quarter notes) of the sound being played.

The average value of the interval at which the [TAP] button was tapped

by finger is set as the BPM.

! When the BPM is set using the [TAP] button, the beat fraction is set

to [1/1] and the time of one beat (quarter note) is set as the effect

time.

! The BPM can be set manually by turning the [TIME] control while

pressing the [TAP] button.

! The BPM can be set manually by pressing the beat button while

pressing [TAP].

! The BPM can be set in units of 0.1 by turning the [TIME] control

while pressing the [TAP] and [AUTO/TAP] buttons.

 Adjusting the amount of effect applied for

different frequency bands

Turn the [EFFECT FREQUENCY (HI, MID, LOW)] control.

See Types of BEAT EFFECT on page 25 for the parameters of the effects

that can be adjusted with the different controls.

 Using the external effector

1 Connect this unit and external effector.

[SEND/RETURN] lights.

For instructions on connections, see Connecting output terminals on

page 7.

2 Press one of the [CH SELECT] buttons.

This selects the channel to which the effect is applied.

19

En

English

3 Press [SEND/RETURN].

[SEND/RETURN] flashes.

4 Press the [ON/ OFF] button.

The sound that has passed through the external effector is output from

the [MASTER] channel.

! When the [ON/ OFF] button is pressed again, the effect turns off.

Controlling connected devices

 Using the SYNC MASTER function

The beat positions and BPMs of tracks being played on Pioneer DJ

players supporting the beat sync function (CDJ-2000nexus) can be

synchronized.

4

5

1

2

3

1

SYNC

Sets synchronization to the master BPM of the players

connected to channels 1 – 4.

2

MASTER

Selects the sync master.

3

BPM setting

Increases or decreases the BPM value displayed in the

BPM display area.

4

BPM display area

Displays one of the two values below, depending on

this unit’s status.

! When this unit is the sync master: Displays the

master BPM value.

! When this unit is not the sync master: Displays the

master BPM that would be displayed if this unit

were the sync master.

5

RELOAD

When this unit is not the sync master, the current

master BPM value is displayed in the BPM display area.

1 Press the [SYNC MASTER/MIDI] button.

[SYNC MASTER] is displayed on the screen.

! The function switches each time the [SYNC MASTER/MIDI] button

is pressed.

2 Operate the player’s sync status.

[SYNC] button: The various players’ sync status can be changed by

pressing PLAYER 1 – 4.

The sync mode switches on and off each time the button is pressed.

Buttons for channels to which no player supporting the beat sync func-

tion is connected cannot be operated.

3 Change the sync master.

Press the button for the player or mixer you want to set as the sync

master.

! It is not possible to set multiple devices as the sync master

simultaneously.

4 Set this unit as the sync master.

Press the [RELOAD] button to display the current master BPM value.

Press [a] or [b] to set the master BPM value.

Press the [MIXER] button to set this unit as the sync master.

! When this unit is the sync master, the master BPM value can be

changed by pressing [a] or [b].

Using the MIDI function

 Operating the DJ software

The DJM-2000NXS also outputs the operating data for the buttons and

dials in MIDI format. If you connect a computer with a built-in MIDI-

compatible DJ software via a USB cable, you can operate the DJ soft-

ware on this unit.

Install the DJ software on your computer in advance. Also, adjust the

audio and MIDI settings for the DJ software.

! For MIDI channel setting instructions, see Changing the settings on

page 27.

1 Connect this unit’s [USB] terminal to the computer.

For details about connections, see Connecting a computer on page 8.

2 Launch the DJ software.

3 Press [ON/OFF] in the [MIDI] section.

Turn the MIDI function on.

Transmission of the MIDI messages begin.

! When the faders and controls are moved, messages are sent accord-

ing to the positions of the faders and controls. For messages output

by this unit, see List of MIDI Messages on page 20.

! When the [START/STOP] button is pressed and held in for more than

2 seconds, a set of MIDI messages corresponding to the button,

fader or control positions is sent (Snapshot).

! The MIDI timing clock (BPM information) is sent regardless of the

[ON/ OFF] button.

! When the [ON/ OFF] button for [MIDI] is pressed again, transmis-

sion of MIDI messages stops.

 Sending the MIDI start and MIDI stop messages

Press the [START/STOP] button for [MIDI].

! The MIDI start and MIDI stop messages are sent alternatively each

time the [START/STOP] button is pressed, regardless of whether the

MIDI function is on or off.

Using the MIDI control screens

This unit is equipped with four types of MIDI control screens. Use them

according to your DJ software.

1 Press the [SYNC MASTER/MIDI] button at the right

side of the touch panel several times.

The [MIDI CONTROL] screen is displayed after the [SYNC MASTER]

screen.

! The function switches each time the [SYNC MASTER/MIDI] button

is pressed.

2 Select a type, from [TYPE A] to [TYPE D].

This selects the type of MIDI control screen.

! When [PAGE1] or [PAGE2] is pressed, the page being displayed

switches.

3 Operate the touch panel buttons or faders.

Transmission of the MIDI messages begin.

For messages output by this unit, see List of MIDI Messages on page 20.

Operating an external MIDI sequencer

This unit sends the tempo of the currently playing source (BPM informa-

tion) as the MIDI timing clock. This can be used to synchronize an exter-

nal MIDI sequencer with the tempo of the source.

! External MIDI sequencers not supporting MIDI timing clocks cannot

be synchronized.

! External MIDI sequencers cannot be synchronized for sources for

which the BPM cannot be measured stably.

! The MIDI timing clock is output even with BPM values input manu-

ally by tapping the [TAP] button with a finger. The MIDI timing clock

output range is 40 BPM to 250 BPM.

1 Connect the [MIDI OUT] terminal to the external

MIDI sequencer’s MIDI IN terminal using a commercially

available MIDI cable.

2 Set the external MIDI sequencer’s sync mode to Slave.

3 Press [START/STOP].

The MIDI start message is sent.

4 Press [ON/OFF] in the [MIDI] section.

Transmission of the MIDI messages begin.

20

En

List of MIDI Messages

Control Panel

Category SW Name SW Type

MIDI Messages

Trigger/Toggle Notes

MSB LSB

CH1

TRIM

VR Bn 01 dd — — — — 0-127

HI

VR Bn 02 dd — — — — 0-127

MID

VR Bn 03 dd — — — — 0-127

LOW

VR Bn 04 dd — — — — 0-127

FILTER

VR Bn 05 dd — — — — 0-127

Channel fader VR Bn 11 dd — — — — 0-127

CROSS FADER ASSIGN

SW Bn 41 dd — — — — 0, 64, 127

CUE

BTN Bn 46 dd — — — Trigger/Toggle OFF=0, ON=127

CH2

TRIM

VR Bn 06 dd — — — — 0-127

HI

VR Bn 07 dd — — — — 0-127

MID

VR Bn 08 dd — — — — 0-127

LOW

VR Bn 09 dd — — — — 0-127

FILTER

VR Bn 0A dd — — — — 0-127

Channel fader VR Bn 12 dd — — — — 0-127

CROSS FADER ASSIGN

SW Bn 42 dd — — — — 0, 64, 127

CUE

BTN Bn 47 dd — — — Trigger/Toggle OFF=0, ON=127

CH3

TRIM

VR Bn 0C dd — — — — 0-127

HI

VR Bn 0E dd — — — — 0-127

MID

VR Bn 0F dd — — — — 0-127

LOW

VR Bn 15 dd — — — — 0-127

FILTER

VR Bn 16 dd — — — — 0-127

Channel fader VR Bn 13 dd — — — — 0-127

CROSS FADER ASSIGN

SW Bn 43 dd — — — — 0, 64, 127

CUE

BTN Bn 48 dd — — — Trigger/Toggle OFF=0, ON=127

CH4

TRIM

VR Bn 50 dd — — — — 0-127

HI

VR Bn 51 dd — — — — 0-127

MID

VR Bn 5C dd — — — — 0-127

LOW

VR Bn 52 dd — — — — 0-127

FILTER

VR Bn 53 dd — — — — 0-127

Channel fader VR Bn 14 dd — — — — 0-127

CROSS FADER ASSIGN

SW Bn 44 dd — — — — 0, 64, 127

CUE

BTN Bn 49 dd — — — Trigger/Toggle OFF=0, ON=127

Crossfader Crossfader VR Bn 0B dd — — — — 0-127

CURVE SETTING

CH EQ (ISOLATOR, EQ) SW Bn 21 dd — — — — 0, 127

CH FADER (

, )

SW Bn 5E dd — — — — 0, 127

CROSS FADER (

, , )

SW Bn 5F dd — — — — 0, 64, 127

MASTER

BALANCE

VR Bn 17 dd — — — — 0-127

MASTER level VR Bn 18 dd — — — — 0-127

CUE

BTN Bn 4A dd — — — Trigger/Toggle OFF=0, ON=127

BOOTH MONITOR

VR Bn 19 dd — — — — 0-127

CH SELECT

1

BTN Bn 22 dd — — — Trigger/Toggle

1

OFF=0, ON=127

2

BTN Bn 23 dd — — — Trigger/Toggle

1

OFF=0, ON=127

3

BTN Bn 24 dd — — — Trigger/Toggle

1

OFF=0, ON=127

4

BTN Bn 25 dd — — — Trigger/Toggle

1

OFF=0, ON=127

MIC

BTN Bn 26 dd — — — Trigger/Toggle

1

OFF=0, ON=127

A

BTN Bn 27 dd — — — Trigger/Toggle

1

OFF=0, ON=127

B

BTN Bn 28 dd — — — Trigger/Toggle

1

OFF=0, ON=127

M

BTN Bn 29 dd — — — Trigger/Toggle

1

OFF=0, ON=127

BEAT EFFECT

TIME

VR Bn 0D MSB Bn 2D LSB —

TIME value (half the

value when FILTER or

PHASER is selected for

EFFECT SELECT)

ON/OFF BTN Bn 40 dd — — — Trigger/Toggle OFF=0, ON=127

AUTO/TAP

BTN Bn 45 dd — — — Trigger/Toggle OFF=0, ON=127

CUE

BTN Bn 4B dd — — — Trigger/Toggle OFF=0, ON=127

TAP

BTN Bn 4E dd — — — Trigger/Trigger OFF=0, ON=127

LEVEL/DEPTH VR Bn 5B dd — — — — 0-127

EFFECT SELECT

DELAY

BTN Bn 2A dd — — — Trigger/Toggle

1

OFF=0, ON=127

MULTI TAP DELAY

BTN Bn 2B dd — — — Trigger/Toggle

1

OFF=0, ON=127

ROLL

BTN Bn 2E dd — — — Trigger/Toggle

1

OFF=0, ON=127

REV ROLL

BTN Bn 2F dd — — — Trigger/Toggle

1

OFF=0, ON=127

TRANS

BTN Bn 35 dd — — — Trigger/Toggle

1

OFF=0, ON=127

GATE

BTN Bn 3D dd — — — Trigger/Toggle

1

OFF=0, ON=127

ECHO

BTN Bn 37 dd — — — Trigger/Toggle

1

OFF=0, ON=127

REVERB

BTN Bn 36 dd — — — Trigger/Toggle

1

OFF=0, ON=127

SLIP ROLL

BTN Bn 3A dd — — — Trigger/Toggle

1

OFF=0, ON=127

FILTER

BTN Bn 3B dd — — — Trigger/Toggle

1

OFF=0, ON=127

PHASER

BTN Bn 39 dd — — — Trigger/Toggle

1

OFF=0, ON=127

SEND/RETURN

BTN Bn 3E dd — — — Trigger/Toggle

1

OFF=0, ON=127

La page charge ...

Pioneer DJ Equipment DJM-2000NXS Manuel utilisateur

Ce manuel convient également à

Pioneer DJ Equipment DJM-2000NXS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents