Titan 0533423C Le manuel du propriétaire

Models:

0533423C

0533423CAA

0533620C

0533620CAA

Models:

0533423S

0533423SAA

0533620S

0533620SAA

Models:

0533423W

0533423WAA

0533620W

0533620WAA

AirCoat

Series

1217 • Form No. 0533842F

Air Powered, Air-Assisted

/ Airless sPrAyer

Air Powered, Air-Assisted /

Airless-sPritzgerät

PulvérisAteur Air Powered,

Air-Assisted / Airless

- gB - oPerAting mAnuAl 2

- d - BetrieBsAnleitung 22

- F - mode d’emPloi 44

oPerAting mAnuAl

2 AirCoat

GB

Warning!

Attention: Danger of injury by injection!

Air-Assisted / Airless units develop extremely high spraying pressures.

Be safety conscious!

1

2

3

Never put your ngers, hands or any other parts of the body into

the spray jet!

Never point the spray gun at yourself, other persons or animals.

Never use the spray gun without safety guard.

Do not treat a spraying injury as a harmless cut. In case of injury

to the skin through coating materials or solvents, consult a doctor

immediately for quick and expert treatment. Inform the doctor

about the coating material or solvent used.

The operating instructions state that the following points must

always be observed before starting up:

1. Faulty units must not be used.

2. Secure Titan spray gun using the safety catch on the trigger.

3. Ensure that the unit is properly grounded / earthed.

4. Check allowable operating pressure of high-pressure hose and spray

gun.

5. Check all connections for leaks.

The instructions regarding regular cleaning and maintenance of

the unit must be strictly observed.

Before any work is done on the unit or for every break in work the

following rules must be observed:

1. Release the pressure from spray gun and hose.

2. Secure the Titan spray gun using the safety catch on the trigger.

3. Switch o unit.

Original Operating Manual

AirCoat 1

GB

Contents

Page

1. Safety regulations for Air-Assisted / Airless spraying ........ 2

1.1 Explanation of symbols used .............................................................. 2

1.2 Compressor safety .................................................................................. 3

1.3 Setting up on uneven surfaces ........................................................... 4

1.4 Freezing Parts ........................................................................................... 4

2. General view of application ............................................................. 5

2.1 Application ................................................................................................ 5

2.2 Coating materials .................................................................................... 5

3. Description of unit................................................................................ 5

3.1 Air-Assisted / Airless / Air-Powered process .................................. 5

3.2 Functioning of the unit ......................................................................... 5

3.3 System diagram ....................................................................................... 6

3.4 Technical data for AirCoat units ......................................................... 7

4. Operation .................................................................................................. 8

4.1 Setup ............................................................................................................ 8

4.2 Automatic lubricator .............................................................................. 9

4.3 High pressure uid regulator .............................................................. 9

4.4 Preparing a new sprayer ..................................................................... 10

4.5 Preparing to spray .................................................................................10

4.6 Spraying ....................................................................................................11

4.7 Pressure relief procedure ...................................................................12

5. Cleanup ....................................................................................................12

5.1 Special cleanup instructions for use with

ammable solvents ..............................................................................12

5.2 Cleaning the sprayer ............................................................................ 12

5.3 Cleaning the air lter ............................................................................13

Page

6. Maintenance..........................................................................................13

6.1 Daily maintenance ................................................................................ 13

6.2 Maintaining the lter assembly........................................................14

6.3 Maintaining the high pressure uid regulator ...........................14

6.4 Maintaining the air motor .................................................................. 15

6.5 Maintaining the uid pump ..............................................................15

7. Troubleshooting .................................................................................15

7.1 Spray gun .................................................................................................15

7.2 Air motor ..................................................................................................16

7.3 Spray patterns ........................................................................................16

7.4 Fluid pump ..............................................................................................17

8. Servicing ..................................................................................................18

8.1 Servicing the air motor ........................................................................18

8.2 Servicing the pump assembly ..........................................................20

Accessories and spare parts ........................................................................66

Spare parts list for the main assembly .................................................. 66/67

Spare parts list for the motor / pump assembly ............................... 68/69

Spare parts list for the upper housing assembly .............................. 70/71

Spare parts list for the air motor ............................................................ 72/73

Spare parts list for the uid pump assembly ..................................... 74/75

Spare parts list for automatic lter, regulator, lubricator

assembly .......................................................................................................... 76/77

Spare parts list for the high-pressure lter ......................................... 78/79

Spare parts list for the high-pressure uid regulator ...................... 80/81

Spare parts list for the cart assembly .................................................... 82/83

Warranty ...............................................................................................................84

2 AirCoat

GB

Safety precautions

1. Safety regulations for Air-Assisted /

Airless spraying

1.1 Explanation of symbols used

This manual contains information that must be read and understood

before using the equipment. When you come to an area that has one

of the following symbols, pay particular attention and make certain

to heed the safeguard.

This symbol indicates a potential hazard that

may cause serious injury or loss of life. Important

safety information will follow.

Attention

This symbol indicates a potential hazard to you

or to the equipment. Important information that

tells how to prevent damage to the equipment or

how to avoid causes of minor injuries will follow.

Danger of skin injection

Danger of fire from solvent and paint fumes

Danger of explosion from solvent, paint fumes

and incompatible materials

Danger of injury from inhalation of harmful

vapors

i

Notes give important information which should

be given special attention.

HAZARD: INJECTION INJURY

A high pressure stream produced by this equipment

can pierce the skin and underlying tissues, leading to

serious injury and possible amputation.

Do not treat a spraying injury as a harmless cut. In

case of injury to the skin through coating materials

or solvents, consult a doctor immediately for quick

and expert treatment. Inform the doctor about the

coating material or solvent used.

PREVENTION:

 • NEVERaimthegunatanypartofthebody.

 • NEVERallowanypartofthebodytotouchtheuidstream.

DONOTallowbodytotouchaleakintheuidhose.

 • NEVERputyourhandinfrontofthegun.Gloveswillnot

provide protection against an injection injury.

 • ALWAYSlocktheguntrigger,shuttheuidpumpo

and release all pressure before servicing, cleaning the tip

guard, changing tips, or leaving unattended. Pressure will

not be released by turning o the compressor. The PRIME/

SPRAYvalveorpressurebleedvalvemustbeturnedtotheir

appropriate positions to relieve system pressure.

 • ALWAYSkeeptipguardinplacewhilespraying.Thetipguard

provides some protection but is mainly a warning device.

 • ALWAYSremovethespraytipbeforeushingorcleaningthe

system.

 • NEVERuseaspraygunwithoutaworkingtriggerlockand

trigger guard in place.

 • Allaccessoriesmustberatedatorabovethemaximum

operating pressure range of the sprayer. This includes spray

tips, guns, extensions, and hose.

HAZARD

: HIGH PRESSURE HOSE

The paint hose can develop leaks from wear, kinking

and abuse. A leak can inject material into the skin.

Inspect the hose before each use.

PREVENTION:

 • Avoidsharpbendingorkinkingofthehigh-pressurehose.The

smallest bending radius amounts to about 20 cm.

 • Donotdriveoverthehigh-pressurehose.Protectagainst

sharp objects and edges.

 • Replaceanydamagedhigh-pressurehoseimmediately.

 • Neverrepairdefectivehigh-pressurehosesyourself!

 • Electrostaticchargingofspraygunsandthehigh-pressure

hose is discharged through the high-pressure hose. For this

reason the electric resistance between the connections of the

high-pressure hose must be equal to or lower than 1M.

 • Forreasonsoffunction,safetyanddurabilityuseonlyoriginal

Titan high-pressure hoses.

 • Beforeeachuse,checkallhosesforcuts,leaks,abrasion

or bulging of cover. Check for damage or movement of

couplings. Immediately replace the hose if any of these

conditionsexist.Neverrepairapainthose.Replaceitwith

another earthed high-pressure hose.

 • Makesurepowercord,airhoseandsprayhosesareroutedin

such a manner to minimize slip, trip and fall hazard.

AirCoat 3

GB

Safety precautions

HAZARD: EXPLOSION OR FIRE

Flammable vapors, such as solvent and paint vapors,

in work area can ignite or explode.

PREVENTION:

 • Useequipmentonlyinwellventilatedarea.Keepagood

supply of fresh air moving through the area to keep the air

within the spray area free from accumulation of ammable

vapors.Keeppumpassemblyinwellventilatedarea.Donot

spray pump assembly.

 • Eliminateallignitionsources,suchaspilotlights,cigarettes,

portable electric lamps and plastic drop cloths (potential static

arc).

 • Keepworkareafreeofdebris,includingsolvent,ragsand

gasoline.

 • Donotplugorunplugpowercords,orturnpowerorlight

switches on or o when ammable vapors are present.

 • Groundequipmentandconductiveobjectsinworkarea.

Make sure the grounding cable is connected from the

grounding lug to a true earth ground.

 • Useonlygroundedhoses.

 • Holdspraygunrmlytothesideofagroundedpailwhen

triggering into pail.

 • Ifthereisstaticsparkingorifyoufeelashock,stop operation

immediately.

 • Knowthecontentsofthepaintandsolventsbeingsprayed.

Read all Material Safety Data Sheets (MSDS) and container

labels provided with the paints and solvents. Follow the paint

and solvent manufacturer’s safety instructions.

 • Donotuseapaintorsolventcontaininghalogenated

hydrocarbons. Such as chlorine, bleach mildewcide,

methylene chloride and trichloroethane. They are not

compatible with aluminum. Contact the coating supplier

about compatibility of material with aluminum.

 • Keepareextinguisherinworkarea.

HAZARD: HAZARDOUS VAPORS

Paints, solvents, and other materials can be harmful

if inhaled or come in contact with body. Vapors can

cause severe nausea, fainting, or poisoning.

PREVENTION:

 • Wearrespiratoryprotectionwhenspraying.Readall

instructions supplied with the mask to be sure it will provide

the necessary protection.

 • Alllocalregulationsregardingprotectionagainsthazardous

vapors must be observed.

 • Wearprotectiveeyewear.

 • Protectiveclothing,glovesandpossiblyskinprotectioncream

are necessary for the protection of the skin. Observe the

regulations of the manufacturer concerning coating materials,

solvents and cleaning agents in preparation, processing and

cleaning units.

HAZARD: GENERAL

This product can cause severe injury or property

damage.

PREVENTION:

 • Followallappropriatelocal,state,andnationalcodes

governing ventilation, re prevention, and operation.

 • Pullingthetriggercausesarecoilforcetothehandthatis

holding the spray gun. The recoil force of the spray gun is

particularly powerful when the tip has been removed and

a high pressure has been set on the airless pump. When

cleaning without a spray tip, set the pressure control knob to

the lowest pressure.

 • Useonlymanufacturerauthorizedparts.Userassumesall

risks and liabilities when using parts that do not meet the

minimum specications and safety devices of the pump

manufacturer.

 • ALWAYSfollowthematerialmanufacturer’sinstructionsfor

safe handling of paint and solvents.

 • Cleanupallmaterialandsolventspillsimmediatelytoprevent

slip hazard.

 • Wearearprotection.Thisunitcanproducenoiselevelsabove

85dB(A).

 • Neverleavethisequipmentunattended.Keepawayfrom

children or anyone not familiar with the operation of airless

equipment.

 • Deviceweighsinexcessof36kg.Three-personliftisrequired.

 • Donotsprayonwindydays.

 • Thedeviceandallrelatedliquids(i.e.hydraulicoil)mustbe

disposed of in an environmentally friendly way.

1.2 Compressor Safety

AirCoat units are Air-Powered (powered by an air compressor).

Follow all safety precautions given by the compressor manufacturer

regarding electrical and general safety.

Locatethecompressoroutsidetheimmediatesprayingareatoavoid

clogged air intake of the compressor with overspray.

If lacquer or other flammable materials are to be

sprayed, ALWAYS locate the compressor outside the

immediate spraying area. Failure to do so may cause

an explosion.

4 AirCoat

GB

Safety precautions

1.3 Setting up on uneven surfaces

The front side of the unit must point downwards to prevent sliding

away.

1.4 Freezing Parts

The temperature of some components of the unit can drop below 32º

F (0º C) during usage, and may show a build-up of frost. Refer to the

diagram below for the area of the pump most likely to reach freezing

temperatures. Avoid touching any components in this area during

usage.

Operating Temperature

This equipment will operate correctly in its intended ambient, at a

minimum between +50ºF (+10°C) and +104ºF (+40°C).

Relative Humidity

The equipment will operate correctly within an environment

at 50% RH, +104ºF (+40°C). Higher RH may be allowed at lower

temperatures.

Measures shall be taken by the Purchaser to avoid the harmful eects

of occasional condensation.

Altitude

This equipment will operate correctly up to 2100 m above mean sea

level.

Transportation and Storage

This equipment will withstand, or has been protected against,

transportation and storage temperatures of -13ºF (-25°C) to 131ºF

(+55°C) and for short periods up to 158ºF (+70°C).

It has been packaged to prevent damage from the eects of normal

humidity, vibration and shock.

3. Description of unit

3.1 Air Powered / Air Assisted process

An Airless piston pump takes in coating material by suction. The

pneumatic piston pump is powered by compressed air provided by

an outside air compressor (Air-Powered).

Cycling of the piston pump moves the material through the pump

and down the uid hose to the spray gun. Pressed through the

tip at very high pressure, the coating material is atomized into ne

particles.

Adding air to assist the spray atomization (Air-Assisted) allows the

coating material to be sprayed at lower pressures while still achieving

an acceptable spray pattern.

This method of spraying has the advantages of the nest atomization,

cloudless operation, and a smooth, bubble-free nish. This method

also oers better transfer eciency and gives the applicator greater

control of spray due to lower uid pressures.

3.2 Functioning of the unit

The following section contains a brief description of the technical

construction for better understanding of the function.

TITANAirCoatarehigh-pressuresprayingunitsdrivenbyairpower

provided by an air compressor.

An air compressor connected by an air hose drives the air motor (1)

which then moves the piston up and down in the material feed pump

(2), drawing up spray material via the siphon hose (3).

The air regulator (4) controls the air pressure being allowed into

the system, and is directly proportionate to the uid pressure being

produced.

Example: AirCoat 423 = 23:1

100 PSI reading at air gauge (5) = 2300 PSI at pump outlet

The inlet valve is opened automatically by the upwards movement

of the piston. The outlet valve is opened when the piston moves

downward.

Coating material ows under high pressure through the high-

pressure hose to the spray gun. When the coating material exits from

the tip it atomises. The atomisation can be ne-tuned by adjusting

the outgoing air regulator (6) as well as the high-pressure uid

regulator (7).

3

4

6

7

1

5

2

AirCoat 5

GB

 Generalviewofapplication

2. General view of application

2.1 Application

This ne-nish spray system is versatile enough to use for low-

pressure ne nish work as well as high-pressure air-assisted

spraying.

Examples of objects to be sprayed

Woodworking projects, cabinetry, fences, house / garage / shed and

other building exteriors, decks, furniture, doors, wood paneling.

2.2 Coating materials

Processible coating materials

i

Pay attention to the spray quality of the coating

materials to be processed.

NoothermaterialsshouldbeusedforsprayingwithoutTitan’s

approval.

Filtering

In spite of the high-pressure lter, ltering of the coating material is

to be recommended in general.

Stir coating material before commencement of work.

i

Make sure when stirring with motor-driven agitators

that no air bubbles are stirred in. Air bubbles disturb

when spraying and can, in fact, lead to interruption

of operation.

Viscosity

It is possible to work with high-viscosity coating materials with these

devices.

If highly viscous coating materials cannot be sucked up, they must be

diluted in accordance with the manufacturer’s instruction.

Two-component coating material

The appropriate processing time must be adhered to exactly. Within

this time rinse through and clean the unit meticulously with the

appropriate cleaning agents.

6 AirCoat

GB

Description of unit

3.3 System diagram

1 Cart assembly (cart models only)

2 Air motor

3 Air hose connection (incoming air)

4 Air pressure gauge (incoming air)

5 Air pressure gauge (outgoing air)

6 Moisture drip tube

 7 Groundingcable

 8 OilcupforPistonLube™

9 Fluid pump

10 Air regulator (incoming air)

 11 Ventedshutovalve

12 Automatic lubricator adjustment

13 Air lter / moisture separator

 14 Gunhoseconnection(air)

15 Air regulator (outgoing air)

16 Filter assembly

17 Fluid pressure gauge

 18 Gunhoseconnection(uid)

19 Pulsation dampener

20 Pressure bleed valve

 21 Bleedhose

22 Siphon tube

1

2

4

5

3

8

7

10

11

15

12

13

14

16

17

18

19

21

20

22

9

6

7

16

20

21

22

17

18

19

8

423S / 620S

AirCoat 7

GB

Description of unit

AirCoat 423 AirCoat 620

Model Number

Cart 0533423C / 0533423CAA 0533620C / 0533620CAA

Wall 0533423W / 0533423WAA 0533620W / 0533620WAA

Spider 0533423S / 0533423SAA 0533620S / 0533620SAA

Pressure Ratio

23:1 20:1

Max. operating pressure

2670 PSI (184 bar) 2320 PSI (160 bar)

Max. air inlet pressure

116 PSI (8 bar) 116 PSI (8 bar)

Cycle rate per gallon / liter

137 / 36 46 / 12

Volume per double stroke

27.7 cc (1.69 in) 81.6 cc (4.98 in)

Max. volume ow @ Cycles per minute (CPM)

60 CPM 0.44 gal (1.66 l)/min 1.29 gal (4.88 l)/min

90 CPM 0.66 gal (2.50 l)/min 1.94 gal (7.34 l)/min

Fluid inlet / outlet

Inlet 3/4”NPT(F) 3/4”NPT(F)

Outlet 3/8"NPT(F) 3/8"NPT(F)

Hose connection

1/4”NPSM(M) 1/4”NPSM(M)

Approximate air requirement (SCFM) per gallon of output @ 116 PSI (8.0 bar) air pressure

6 SCFM (0.17 m/min) 18 SCFM (0.51 m/min)

Air inlet / outlet

Inlet 3/8”NPT(M) 3/8”NPT(M)

Outlet 3/8"NPT(M) 3/8"NPT(M)

Max. sound pressure level

97dB* 98dB*

Weight

Cart 66.1 lbs (29.9 kg) 80 lbs (36.3 kg)

Wall 50.7 lbs (22.7 kg) 64 lbs (29.0 kg)

Spider 46.3 lbs (21.3 kg) 62 lbs (28.1 kg)

Max. viscosity

50.000 mPa·s 50.000 mPa·s

Dimensions L x W x H

Cart 19.75" x 18.5" x 40" (50.16 cm x 47 cm x 101.6 cm) 19.75" x 18.5" x 40" (50.16 cm x 47 cm x 101.6 cm)

Wall 14.5" x 11.5" x 30" (36.8 cm x 29.2 cm x 76.2 cm) 14.5" x 12" x 34.5" (36.8 cm x 30.5 cm x 87.6 cm)

Spider 19" x 17" x 36.3" (48.3 cm x 43.2 cm x 92.2 cm) 19" x 17" x 39.1" (48.3 cm x 43.2 x 99.3 cm)

Max. temperature of pre-heated coating material

140º F (60º C)

Filter insert (standard equipment)

60 mesh, 97 cm (15 In)

 * Placeofmeasurement:1mdistancefromunitand1.60mabovereverberantoor,120bar(12MPa)

operating pressure.

3.4 Technical data for AirCoat units

8 AirCoat

GB

Operation

4. Operation

This equipment produces a uid stream at extremely

high pressure. Read and understand the warnings

in the Safety Precautions section at the front of this

manual before operating this equipment.

4.1 Setup

1. Make sure the siphon hose (g. 5, 1) is connected to the uid

section (2) and the bleed hose (3) is connected to the bleed

valve (4).

Spider models - Make sure the siphon tube is threaded into

the uid pump and tightented wrench tight.

2. Thread the suction tube lter (5) onto the metal suction tube.

3

1

5

2

4

 3. Lockthegunbyippingthetriggerlockintolockposition

(see spray gun manual).

 4. Usingawrench,attachaminimumof50’of1/4”nylonairless

spray hose to the material outlet tting (g. 6, item 1) on the

pump. Tighten securely.

5. Attach the spray hose to the material inlet tting on the spray

gun.Usingtwowrenches(oneonthegunandoneonthe

hose), tighten securely.

1

2

Make sure all airless hoses and spray guns are

electrically grounded and rated for at least 2800 PSI

(19 MPa) uid pressure.

6. Attach the air hose to the air outlet tting (g. 6, item 2) on

the sprayer. Tighten securely.

7. Attach the air hose coupling to the air inlet tting on the spray

gun. Attach the air hose to the coupling. Tighten securely.

Reversing the hose connections could result in

serious injury. Make sure the airless spray hose is

connected from the material outlet fitting on the

sprayer (1) to the material inlet fitting on the gun

and the air hose is connected from the air outlet

fitting on the sprayer (2) to the air inlet fitting on the

gun.

 8. Filltheoilcup1/2fullwithPistonLube(P/N314-480).This

extends packing life.

Attention

Piston Lube prevents increased wear and tear to the

packings.

 9. Verifythattheaircompressormeetsthepowerrequirements

necessary to eectively power the sprayer. See “Technical

Data”, section 3.4 to determine air requirements.

i

The requirements will vary on each model.

10. Prior to connecting the compressor to the unit, perform the

following in order to prevent accidental startup:

a. Close the shuto valve (g 7, item 1). The gure shows the

handle in the closed position.

b. Turn the air regulator (2) fully counterclockwise to its lowest

pressure setting.

c. Open the bleed valve (3) by turning it fully counterclockwise.

The bleed valve handle should be pointing down.

3

5

1

2

4

 11. Usingawrench,removetheredplugfromtheairhosetting

(Fig. 8, item 1). Attach the air hose and tighten wrench tight.

Allunitsareequippedwitha3/8”NPT(M)nipple.

4.2 Automatic Lubricator

The automatic lubricator (Fig. 10, item 1) provides lubrication to the

air that is being delivered to the system. Check the level through the

openings (2) in the side of the air motor shroud.

After relling the reservoir, the automatic lubricator will need

adjusting. Turn the adjusting screw (1) clockwise to increase the

AirCare™injectionrateandcounterclockwisetodecreaseit.

1

2

Check the injection rate by observing the ow through the openings

in the side of the air motor shroud.

 • Theproperowrateis1dropofAirCare™perminute.

 • Inhumidweatherwhenicingmayoccur,increasethe

injection rate.

 • Theinjectionratecomespre-setto1drop/30sec.

4.3 High Pressure Regulator

The high pressure regulator is designed to allow the user to ne-tune

the uid pressure to the spray gun.

To adjust the regulator:

1. Turn the adjustment knob (1) counterclockwise. Stop rotating

the adjustment knob when you no longer feel resistance from

the spring.

i

Whenever reducing pressure, make sure there is no

pressure in the spray hose in order to achieve an

accurate reading at the pressure gauge. Follow the

Pressure Relief Procedure (section 4.7) to relieve any

pressure in the spray hose.

2. Turn the adjustment knob clockwise to increase uid pressure.

1

AirCoat 9

GB

Operation

1

Proper earthing (grounding) is important. The

passage of some materials through the nylon uid

hose will build up a static electric charge, which if

discharged, could ignite solvent vapors present and

create an explosion.

12. Make sure the sprayer is earthed (grounded). All sprayers are

equipped with a earthing (grounding) cable (1). Clip the end

of the grounding cable to a true earth ground.

1

13. Strain all paints with a nylon strainer to ensure trouble free

operation and freedom from frequent cleaning of the inlet

screen and gun lter.

14. Make sure the spray area is well ventilated to prevent

hazardous operation with volatile solvents or exhaust fumes.

If lacquer or other flammable materials are to be

sprayed, ALWAYS locate the compressor outside the

immediate spraying area. Failure to do so may cause

an explosion.

 15. Locatethecompressoroutsidetheimmediatesprayingarea

to avoid clogged air intake of the compressor with overspray.

4.5 Preparing to Spray

Beforespraying,itisimportanttomakesurethattheuidinthe

system is compatible with the paint that is going to be used.

i

Incompatible uids and paint may cause the valves

to become stuck closed, which would require

disassembly and cleaning of the sprayer’s uid

section.

Attention

Always keep the trigger lock on the spray gun in the

locked position while preparing the system.

1. Place the siphon tube into a container of the appropriate

solvent for the material being sprayed.

i

If you are spraying a water-based latex, ush with

warm, clean water. If you are using any other

material, check with the material manufacturer for a

compatible solvent.

2. Place a metal container under the bleed hose.

3. Close the shuto valve (g. 12, item 1). The gure shows the

handle in the closed position.

4. Turn on the air compressor.

5. Turn the air regulator (2) fully counterclockwise to its lowest

pressure setting.

6. Open the bleed valve (3) by turning it fully counterclockwise.

The bleed valve handle should be pointing down.

7. Open the shuto valve (1). The handle should now be in line

with the valve.

8. Turn the air regulator (2) clockwise to increase pressure until

the sprayer cycles evenly and solvent ows freely from the

bleed hose.

9. Allow the sprayer to run for 15–30 seconds to ush the test

uid out through the bleed hose and into the waste container.

10. Turn o the sprayer.

a. Turn the air regulator fully counterclockwise to its lowest

pressure setting.

b. Close the shuto valve.

11. Close the bleed valve by turning it fully clockwise. The bleed

valve handle should be horizontal.

12. Open the shuto valve (1). The handle should now be in line

with the valve. The system is now under pressure.

13. Turn the air regulator clockwise to increase pressure until the

sprayer cycles evenly. The air regulator gauge should read

between 60-80 PSI (4 - 5.5 bar).

i

The air regulator can be locked into place by pushing

down on the knob. Unlock the regulator by pulling

the knob out.

 14. Unlockthegunbyturningtheguntriggerlocktothe

unlocked position.

Ground / Earth the gun by holding it against the

edge of the metal container while flushing. Failure

to do so may lead to a static electric discharge, which

may cause a fire.

15. Trigger the gun into the metal waste container until the old

solvent is gone and fresh solvent is coming out of the gun.

 16. Lockthegunbyturningtheguntriggerlocktothelocked

position.

4.4 Preparing a New Sprayer

If this unit is new, it is shipped with test uid in the uid section to

prevent corrosion during shipment and storage. This uid must be

thoroughly cleaned out of the system with cleaning agent before you

begin spraying.

Attention

Always keep the trigger lock on the spray gun in the

locked position while preparing the system.

1. Place the siphon tube into a container of mineral spirits.

2. Place a metal container under the bleed hose.

3. Close the shuto valve (g. 12, item 1). The gure shows the

handle in the closed position.

4. Turn on the air compressor.

5. Turn the air regulator (2) fully counterclockwise to its lowest

pressure setting.

6. Open the bleed valve (3) by turning it fully counterclockwise.

The bleed valve handle should be pointing down.

3

5

1

2

4

7. Open the shuto valve (1). The handle should now be in line

with the valve.

8. Turn the air regulator (2) clockwise to increase pressure until

the sprayer cycles evenly and solvent ows freely from the

bleed hose.

9. Allow the sprayer to run for 15–30 seconds to ush the test

uid out through the bleed hose and into the waste container.

10. Turn o the sprayer.

a. Turn the air regulator fully counterclockwise to its lowest

pressure setting.

b. Close the shuto valve.

10 AirCoat

GB

Operation

17. Adjust the spray pattern to the desired size and atomization.

 a. Usetheupperpressureregulatorknob(2)tocontrolthe

ow of material to the gun. Once the air pressure has been

established, lock the air regulator by pushing down on the

knob.

 b. Usethelowerpressureregulator(4)tocontroltheamountof

atomization air available to the gun.

 c. Usethepatternadjustmentknobonthesprayguntonetune

the spray pattern.

 d. Usethepulsationdampener(5)toeliminatepulsationsinthe

spray pattern and to ne tune the spray pressure. Turn the

adjustment knob clockwise to increase the uid pressure. Turn

the knob counterclockwise to decrease the uid pressure.

i

Whenever reducing pressure, make sure there is no

pressure in the spray hose in order to achieve an

accurate reading at the pressure gauge. Follow the

Pressure Relief Procedure (section 4.7) to relieve any

pressure in the spray hose.

POSSIBLE INJECTION HAZARD. Do not spray

without the tip guard in place. Never trigger the

gun unless the tip is in either the spray or the unclog

position. Always engage the gun trigger lock before

removing, replacing or cleaning tip.

DO NOT exceed an air regulator gauge reading of

116 PSI (8.0 bar).

i

Using a higher pressure than required will only

wear out tips. Use the guidelines in establishing the

lowest pressures for proper atomization.

Consult the materials manufacturer for guidelines in

establishing the correct uid pressure.

4.7 Pressure Relief Procedure

Be sure to follow the Pressure Relief Procedure when

shutting the unit down for any purpose, including

servicing or adjusting any part of the spray system,

changing or cleaning spray nozzles, or preparing for

cleanup.

 1. Lockthespraygunbyturningtheguntriggerlocktothe

locked position.

2. Close the shuto valve.

3. Open the bleed valve by turning it fully counterclockwise.

 4. Unlockthegunbyturningtheguntriggerlocktothe

unlocked position.

5. Hold the metal part of the gun rmly to the side of a metal

waste container to earth the gun and avoid a build up of static

electricity.

6. Trigger the gun to remove any pressure that may still be in the

hose.

 7. Lockthegunbyturningtheguntriggerlocktothelocked

position.

POSSIBLE INJECTION HAZARD

Refer to your spray gun manual for information

regarding the locking mechanism and how to

properly lock the spray gun.

17. Set down the gun and increase the pressure by turning the air

regulator slowly clockwise to a maximum of 116 PSI (8.0 bar).

DO NOT exceed an air regulator gauge reading of

116 PSI (8.0 bar).

18. Check the entire system for leaks. If leaks occur, turn the

sprayer o and follow the “Pressure Relief Procedure” in this

manual before tightening any ttings or hoses.

19. Follow the “Pressure Relief Procedure” (section 4.7) in this

manual before changing from solvent to paint.

Be sure to follow the Pressure Relief Procedure when

shutting the unit down for any purpose, including

servicing or adjusting any part of the spray system,

changing or cleaning spray tips, or preparing for

cleanup.

4.6 Spraying

1. Place the siphon hose into a container of paint.

2. Place the bleed hose into a metal waste container.

3. Close the shuto valve (g. 12, item 1). The gure shows the

handle in the closed position.

4. Turn on the air compressor.

5. Turn the air regulator (2) fully counterclockwise to its lowest

pressure setting.

6. Open the bleed valve (3) by turning it fully counterclockwise.

The bleed valve handle should be pointing down.

7. Open the shuto valve (g. 12, item 1). The handle should

now be in line with the valve.

8. Turn the air regulator (2) clockwise to increase pressure until

the sprayer cycles evenly and material ows freely from the

bleed hose.

9. Turn o the sprayer.

a. Turn the air regulator fully counterclockwise to its lowest

pressure setting.

b. Close the shuto valve.

10. Remove the bleed hose from the waste container and place

it into the container of material. Close the bleed valve by

turning it fully clockwise.

11. Open the shuto valve. The handle should now be in line

with the valve.

12. Turn the air regulator (2) clockwise to increase pressure until

the sprayer cycles evenly. The air regulator gauge should read

between 30-40 PSI (2 - 2.75 bar).

13. Turn the lower air pressure regulator (4) clockwise until the

lower pressure gauge reads 20-25 PSI (1.38 - 1.72 bar)

 14. Unlockthegunbyturningtheguntriggerlocktothe

unlocked position.

Ground / Earth the gun by holding it against the

edge of the metal container while flushing. Failure

to do so may lead to a static electric discharge, which

may cause a fire.

15. Trigger the gun into the metal waste container until all air and

solvent is ushed from the spray hose and paint is owing

freely from the gun.

16. When material reaches the spray tip, spray a test area on a

piece of cardboard to check the spray pattern.

AirCoat 11

GB

Operation

12 AirCoat

GB

Cleanup

5. Cleanup

Attention

The sprayer, hose, and gun should be cleaned

thoroughly after daily use. Failure to do so permits

material to build up, seriously aecting the

performance of the unit.

Always spray at minimum pressure with the gun

nozzle tip removed when using mineral spirits or

any other solvent to clean the sprayer, hose, or

gun. Static electricity buildup may result in a re or

explosion in the presence of ammable vapors.

5.1 Special cleanup instructions for use with

ammable solvents

 • Alwaysushspraygunpreferablyoutsideandatleastone

hose length from spray pump.

 • Ifcollectingushedsolventsinaonegallonmetalcontainer,

place it into an empty ve gallon container, then ush

solvents.

 • Areamustbefreeofammablevapors.

 • Followallcleanupinstructions.

5.2 Cleaning the sprayer

1. Follow the “Pressure Relief Procedure” found in the Operation

section of this manual, section 4.7.

2. Remove the gun tip and tip guard and clean with a brush

using the appropriate solvent.

3. Place the siphon tube into a container of the appropriate

solvent.

Attention

Use only compatible solvents when cleaning

out oil based enamels, lacquers, coal tar, and

epoxies. Check with the uid manufacturer for the

recommended solvent.

4. Place a metal container under the bleed hose.

5. Close the shuto valve (g. 13, item 1). The gure shows the

handle in the closed position.

6. Start the compressor.

7. Turn the air regulator (2) fully counterclockwise to its lowest

pressure setting.

8. Open the bleed valve (3) by turning it fully counterclockwise.

The bleed valve handle should be pointing down.

9. Turn the high pressure uid regulator knob (5)

counterclockwise until the spring tension is relieved.

3

5

1

2

4

10. Open the shuto valve (g. 13, item 1). The handle should

now be in line with the valve.

11. Allow the solvent to circulate through the sprayer and ush

the material out of the bleed hose into the metal waste

container.

12. Close the shuto valve (g. 13, item 1). The gure shows the

handle in the closed position.

13. Close the bleed valve by turning it fully clockwise.

14. Open the shuto valve (g. 13, item 1). The handle should

now be in line with the valve.

Ground / Earth the gun by holding it against the

edge of the metal container while flushing. Failure

to do so may lead to a static electric discharge, which

may cause a fire.

15. Trigger the gun into the metal waste container until the paint

is ushed out of the hose and solvent is coming out of the

gun.

16. Continue to trigger the spray gun into the waste container

until the solvent coming out of the gun is clean.

i

For long-term or cold weather storage, pump

mineral sprits through the entire system.

17. Follow the “Pressure Relief Procedure” found in the Operation

section of this manual.

18. Store the sprayer in a clean, dry area.

Attention

Do not store the sprayer under pressure.

AirCoat 13

GB

Cleanup Maintenance

5.3 Cleaning the air lter

The air lter blocks any debris or particles that might be present in

the supplied air from the air compressor. It is important that this lter

be checked after every use.

1. Follow the “Pressure Relief Procedure” found in the Operation

section of this manual, section 4.7.

2. Remove the top four screws that secure the front shroud. The

two screws at the bottom front do not need to be removed.

3. After the four top screws are removed, ip open the front

shroud.

4. Remove the larger tube from the quick-lock tting on the air

inlet tting (Fig. 14, item 1). The other end of the tube can

remain connected. It can be twisted within the bottom tting

so that it will be out of the way.

 5. Unthreadthelterbowl(2)thatislocatedunderneaththeair

motorshroud.BecarefulnottolosetheO-ring(3)thatmay

fall out of the bowl. The clear tube may slip o of the tting

on the bottom of the housing. It can be reinstalled later.

i

For model 620 units, press the red lock release on

the gray shroud and turn 1/4 turn counterclockwise

to remove.

 6. Unthreadthelterassemblyfromthesprayer.Becarefulnot

to lose the cap (4), spring (5), lter (6) or stem (7).

 7. Removeandinspectthelter(P/N0533557,6).Ifdirty,clean

with warm, soapy water.

8. Prior to reassembly, tilt the sprayer on its back.

9. Make sure all parts of the lter are reassembled prior to

reinstallation (g. 14, items 4-7).

10. Thread the entire lter assembly back into its housing in the

sprayer.

11. Make sure the O-ring (3) is in place. Thread the bowl into

position underneath the motor shroud.

Model 620 - with the bowl inside the shroud, insert into place

and turn clockwise until the two parts lock into place. Make

sure the red lock release is facing towards the front of the

sprayer.

12. Flip the front shroud back into place and secure with the four

top screws.

1

2

3

4

5

6

7

6. Maintenance

Before proceeding, follow the Pressure Relief

Procedure outlined previously in this manual.

Additionally, follow all other warnings to reduce the

risk of an injection injury, injury from moving parts

or electric shock. Always unplug the sprayer before

servicing!

6.1 Daily Maintenance

Two daily procedures are required for routine operator maintenance

on this sprayer:

 A. Lubricatingtheupperpackings.

 B. Cleaningtheinletscreen

A) Lubricating the Upper Packings

1. Clean out the paint that has seeped past the upper packings

into the packing oil reservoir (g. 15, item 1) above the uid

section.

 2. Fillthepackingoilreservoir1/2fullwithPistonLube(P/N314-

480) supplied by the factory. This will extend packing life.

1

i

Do not over-ll the reservoir so that it overows and

drips into the paint.

B) Cleaning the Inlet Screen

1. The inlet screen will clog and must be cleaned at least once a

day.

 2. Loosenandremovetheinletscreen(1)fromthebottomof

the metal suction tube.

3. Clean thoroughly with the appropriate solvent.

1

14 AirCoat

GB

Maintenance

6.2 Maintaining the Filter Assembly

Clean the lter regularly. Dirty or clogged lters can greatly reduce

ltering ability and cause a number of system problems including

poor spray patterns, clogged spray tips, etc.

Cleaning (Fig. 17)

1. Follow the “Pressure Relief Procedure” found in the Operation

section of this manual (section 4.7).

2. Remove lter cap assembly (1).

3. Pull the lter element (2) with support (3) straight out of the

lter body (6).

4. Clean inside the lter body, lter element with support, and

lter cap assembly using the appropriate solvent.

i

Use care in handling parts as dirt, debris, scratches,

or nicks may prevent o-rings or gaskets from sealing.

This lter element lters from the outside in. Be

sure to clean the lter element thoroughly. Soak in

solvent to loosen hardened paint or replace.

1

2

6

5

4

3

Inspection (Fig. 17)

Inspect all parts of the lter assembly before reassembly.

1. Inspect the support inside the lter element. If the support

has pressure cuts or scratches, replace the lter element.

2. Inspect the two PTFE gaskets (4, 5) for deformity, nicks, or

cuts. Replace, if needed.

Reassembly (Fig. 17)

After cleaning and inspecting all parts, reassemble the lter.

1. Place the lter element (2) with support (3) into the lter body

(6).

2. Place the thin PTFE gasket (5) onto the step at the top of the

lter body (6).

3. Place the PTFE O-ring (4) into the groove of the base of the

lter body threads (6).

4. Tighten the lter cap assembly (1) onto the lter body (6).

6.3 Maintaining the High Pressure Fluid

Regulator

Regular inspection and lubrication of the regulator are necessary to

keep it working properly.

Cleaning (Fig. 18)

1. Follow the “Pressure Relief Procedure” found in the Operation

section of this manual.

2. Remove the entire high pressure uid regulator assembly

from the lter assembly.

3. Turn the regulator knob (1) counterclockwise until it is

removed.

 4. Usingawrenchonthehexofthecylinder(2),loosenand

remove the cylinder from the regulator housing (3), being

careful not to lose the spring locator (4).

5. Inside the cylinder, remove the spring clip (5), washer (6) and

packing (7).

 6. Usingawrenchontheatsofthecap(8),loosenandremove

the cap.

 7. Usinganallenwrench,loosenandremovethetwobolts(9)

from the regulator housing. The bar and piston assembly (10)

willcomeloose.Becarefulnottolosetheballvalve(11).

8. Thoroughly clean inside the cylinder (2), inside the regulator

housing (3), and the cap (8) with the appropriate solvent.

Clean the washer (6), packing (7) and the bar and piston (10).

1

2

5

8

9

11

14

15

12

13

6

7

4

3

10

Inspection (Fig. 18)

Inspect all parts of the high pressure uid regulator before

reassembly.

1. Inspect the spring locator (4), packing (7), ball valve (11) and

seat (12). If worn or damaged, replace.

2. Inspect the piston assembly (10). If the piston is worn, replace.

3. Inspect the O-rings (13) in the regulator housing. If worn or

damaged, replace and lubricate with lithium grease.

AirCoat 15

GB

Maintenance Troubleshooting

7. Troubleshooting

7.1 Spray Gun

Problem Cause Solution

A. Spitting gun 1. Air in system

2. Dirty gun

 3. Needleassemblyoutofadjustment

 4. Brokenorchippedseat

1. Inspect connections for air leaks.

2. Disassemble and clean.

3. Inspect and adjust.

4. Inspect and replace.

 B. Gunwillnotshuto 1. Worn or broken needle & seat

 2. Needleassemblyoutofadjustment

3. Dirty gun

1. Replace.

2. Adjust.

3. Clean.

 C. Gundoesnotspray  1. Nopaint

2. Plugged lter or tip

 3. Brokenneedleingun

1. Check uid supply.

2. Clean.

3. Replace.

D. Insucient material supply. 1. Material pressure set too low.

 2. Blockedspraygunlterorpumphigh

pressure lter.

3. Tip is blocked.

4. Tip is too small.

1. Increase the material pressure at pump.

2. Clean or replace the gun lter and/or pump high

pressure lter.

3. Clean the tip.

4. Select a larger tip.

E. Poor spraying pattern. 1. Tip is too large.

2. Material pressure at the pump is set too

low.

3. Material viscosity is too high.

4. Atomizing air is set incorrectly.

5. Worn tip.

1. Select a smaller tip.

2. Increase the material pressure at the pump.

3. Dilute the material according to the material

manufacturer’s instructions.

4. Adjust the atomizing air using the gun air adjustment

knob or pressure regulator at the air outlet.

5. Replace with a new tip.

 F. Leakingairvalve. 1. Damaged air valve seal. 1. Replace the air valve seal.

Reassembly (Fig. 18)

After cleaning and inspecting all parts, reassemble the regulator

assembly.

 1. Lubricatepacking(7)withalithiumgrease.Replaceintothe

cylinder with the lips facing up.

2. Replace the washer (6) on top of the packing (7). Secure both

in place with the spring clip (5).

3. Slide bolts (9) through the upper bar (14) and into the sleeves

(15). Reinstall into the housing (3), making sure the ball valve

pin (11) is inserted into the center hole of the upper bar (14).

4. Thread the bolts into the lower bar and piston (10) assembly

and tighten securely.

 5. LubricatetheO-rings(13)insidetheregulatorhousing.

Thread the cylinder (2) into the regulator housing and tighten

with a wrench.

6. Thread the cap (8) onto the top of the regulator housing and

tighten with a wrench.

7. Making sure the piston (10) is seated inside the spring locator

(4), thread the regulator knob onto the bottom of the cylinder

(2). Hand-tighten.

8. Reattach the entire regulator assembly to the lter assembly.

Tighten the tting with a wrench.

6.4 Air Motor Maintenance

Air motors require a normal maintenance and service inspection at

1500 hours service. Service procedure includes replacement of motor

service kit. It is suggested that one motor service kit be kept on hand

for normal maintenance and emergency repairs. Check the individual

model’s specications for correct part numbers.

6.5 Maintaining the Fluid Pump

If the sprayer is going to be out of service for an extended period of

time,itisrecommendedthatfollowingcleanup,LiquidShield™be

introduced as a preservative. Packings may tend to dry out from lack

of use. This is particularly true of the upper packing set for which

upperpackinglubricantPistonLube(P/N314-480)isrecommended

in normal usage.

If the sprayer has been out of service for an extended period of time,

it may be necessary to prime the pump with solvent. It is extremely

important that the threads on the siphon hose coupling are properly

sealed. Any air leakage will produce erratic operation of the sprayer

and may damage the system. The up and the down strokes should

be approximately equal in time (one should not be faster than the

other). A fast up or down stroke may indicate air in the system or

malfunctioning valve or seats (see the Troubleshooting section).

16 AirCoat

GB

Troubleshooting

7.3 Spray Patterns

Problem Cause Solution

A. Tails 1. Inadequate uid delivery 1. Fluid not atomizing correctly:

Increase uid pressure. Change to smaller tip orice

size. Reduce uid viscosity. Reduce hose length.

Clean gun and lter(s). Reduce number of guns using

pump.

 B. Hourglass 1. Inadequate uid delivery 1. Same as above.

C. Distorted 1. Plugged or worn tip 1. Clean or replace tip.

D. Pattern expanding and

contracting (surge)

1. Suction leak

2. Pulsating uid delivery

1. Inspect for suction hose leak.

2. Change to a smaller tip orice size. Install pulsation

dampener in system or drain existing one. Reduce

number of guns using pump. Remove restrictions in

system; clean tip screen if lter is used.

E. Round pattern. 1. Worn tip

2. Fluid too heavy for tip

1. Replace tip.

2. Increase pressure. Thin material. Change nozzle tip.

7.2 Air Motor

Problem Cause Solution

A. Motor stops at top or bottom

of stroke - air does not exhaust

when gun is open.

1. Piston rod is loose where it connects to the

uid section.

2. Trip springs or valve spring broken.

3. Motor is frozen due to icing or lack of

lubrication.

1. Tighten connection.

2. Inspect and replace where neessary.

 3. ChecktheAir-Care™uidlevelintheAutomatic

Lubricator.Iflow,addAir-Care™toreservoir.

If condition persists, check air supply for

contamination.

 B. Motorstops,blowsairfrom

exhaust when gun is open.

1. See above.

2. Air valve is in dead stall position.

3. O-rings were worn or damaged.

1. See above.

2. Remove one trip spring retainer, trip spring and ball.

Push spool valve up or down, lubricate, reassemble

and restart.

3. Install minor service kit and follow instructions in

Servicing section of manual.

If dust or dirt is found inside motor, check air supply for

contamination.

AirCoat 17

GB

Troubleshooting

7.4 Fluid Pump

Problem Cause Solution

A. Pump delivers on upstroke only

or goes up slowly and down fast

(commonly called downstroke

dive).

 1. Lowerfootvalveballisnotseatingdueto

trash or wear.

2. Material to viscous to siphon.

3. Air leaking in on siphon side or damaged

siphon hose. Siphon may be too small for

heavy material.

 4. Upperpackingnut(ifapplicable)islooseor

upper packings are worn.

1. Remove foot valve assembly. Clean and inspect. Test

foot valve by lling with water. If ball fails to seal the

seat, replace ball.

2. Thin material - contact manufacturer for proper

thinning procedures.

3. Tighten all connections between pump and paint

container. If damaged, replace. Switch to bigger

siphon set.

4. If tightening upper packing nut does not correct,

change upper packings.

 B. Pumpdeliversondownstroke

only or goes up fast and down

slowly.

 1. Upperballisnotseatingduetotrashor

wear.

 2. Lowerpackingsetisworn.

1. Check upper seat and ball with water. If ball fails to

seal seat, replace.

2. Replace packing set is worn.

C. Pump moves up and down fast,

not delivering material.

1. Material container is empty or material is

too thick to ow through the siphon hose.

 2. Bottomballstucktofootvalveseat.

3. Siphon hose is kinked or loose.

1. Rell with new material. If too thick, remove siphon

hose, immerse uid section in material, and start

pump to prime. Add thinner to material. Change to

bigger siphon set. Open bleed valve to remove air

and restart pump.

2. Remove foot valve. Clean ball and seat.

3. Straighten.

D. Pump moves up and down

slowly when spray gun is shut

o.

 1. Looseconnections.Bleedvalveisopen

partiallyorbleedvalveisworn.Lower

packing set is worn.

 2. Upperand/orlowerballnotseating.

1. Check all connections between pump and gun.

Tighten as necessary. If material is owing from

bleed hose, close bleed valve or replace if necessary.

Should none of above be evident, replace lower

packing.

2. Reset balls by cleaning.

 E. Notenoughuidpressureat

gun.

1. Spray tip is worn.

2. Compressor (air operated units only) too

small. Outlet lter or gun lter is clogged.

 3. Lowvoltageand/orinadequateamperage.

4. Hose size or length is too small or too long.

1. Replace.

2. Clean or replace lter. Recommend proper hose size

and/or air compressor size.

3. Check electrical service. Correct as required.

4. Increase hose size to minimize pressure drop through

hose and/or reduce hose lengths.

F. Pump chatters on up or down

stroke

1. Solvent has caused upper packing to swell,

or packing is too tight.

 1. Backoupperpackingnut1/4turn(ifapplicable)

and restart pump. Repeat if necessary.

18 AirCoat

GB

Servicing

8. Servicing

8.1 Servicing the Air Motor

The Air Motors require a normal mantenance inspection at 1500

hours of service on the non-circulating models.

ServiceprocedureincludesreplacementoftheMotorServiceKit(see

next page for part numbers). It is suggested that one Motor Service

Kitbekeptonhandfornormalmaintenanceandemergencyrepairs.

SeenextpageforpartnumbersoftheMotorKit.

Accessing the Air Motor (Fig. 19)

In order to be able to access the air motor, certain components must

be removed.

i

The piston rod in the uid pump should be in the

lowest-dead center position prior to performing

these steps. The shuto valve can be used to allow

the sprayer to run slowly.

1. Remove all external air and uid hoses from the sprayer.

2. Press the collar on the lower air hose tting (1) and remove

the air hose from the lower air hose tting only.

 3. Underneaththefrontshroud,removetheclearairtube(2)

that is connected to the air regulator reservoir.

 4. Loosenthecylindercapnut(3)sothatitshandleisoriented

side-to-side and is aligned with the gap in the top shroud (4).

5. Remove the lower screws (5) that secure the motor shroud

assembly (6) to the air motor. Once removed, carefully lift the

entire assembly o of the air motor.

3

6

4

2

5 (x6)

1

Disassembling the Air Motor (Fig. 21)

1. Remove the pin (1) that connects the air motor piston rod

(2)withtheuidpumpdisplacementrod(3).Usinga

wrench on the ats of the displacement rod (3), unthread the

displacement rod from the piston rod.

 2. Removethelowerstanchionnuts(4).Gentlylowertheuid

pump (5) away from the air motor.

 3. Fullyloosenthecylindercapnut(6).Gentlypullupthe

cylindercapnuttoexposethetriprod(7).Usingapliers,grip

the hex nut (7) on the trip rod, and loosen and remove the

cylinder cap nut from the trip rod.

Attention

Be careful not to damage the outer surface of the

trip rod. A damaged trip rod will cause the air motor

to operate incorrectly.

4. Remove the screws (8) that hold the cylinder (9) and air motor

base(10)together.Becarefulnottolosetheshroudbrackets

or washers that will be removed also. Pull o the cylinder.

Remove the o-ring (31) on top of the motor base.

Attention

When removing the cylinder, remove it straight up.

Avoid tilting. Tilting can damage the cylinder wall.

5. Pull the piston assembly (11) from the air motor base (10). The

piston rod (2) will remain attached within the piston.

6. Check the bearing down in the center of the air motor base. If

worn, replace the motor housing.

i

If the bearing is worn, the entire air motor base will

need to be replaced.

7. Place the ats of the piston rod (2) into a vise to secure the

entire piston rod assembly.

 8. Usingascrewdriver,pushdownonthetriprodyoke(g.20,

item 12) and snap the toggles (13) down.

PINCH HAZARD. Keep your fingers clear of the

toggle assemblies (13) when you are snapping the

toggles up or down.

9. Place the tip of a screwdriver between the piston lugs (14)

and below the toggle rocker (15) (place screwdriver at place

marked by asterisk, g. 20).

10. Push forward and up with the screwdriver to compress the

springs on the toggle assembly (13) up and away from the

piston lugs. Remove the springs (16) toggle arms (17), and

toggle pins (18).

i

Place your hand above the toggle assembly as you

perform this step. This will prevent parts from

popping out.

14

15

*

12

13

18

16

18

17

11. Straighten the lockwires (g. 21, item 19) and remove them

from the upper valve nuts (20). Remove the upper valve nuts.

12. Remove the hex nut from the trip rod (7). Remove the trip

rod yoke (12) and the actuator (21). Thread the hex nut (7)

back onto the trip rod to prevent it from sliding down into the

piston rod.

13. Remove the lower valve nuts (22) and remove the inlet valve

poppets (23). Make sure the spring clips (24) are not worn or

damaged, and that they properly guide the actuator (21).

11. Remove the exhaust valve poppets (25) by cutting them with a

side cutter. Remove them from the actuator.

La page charge ...

Titan 0533423C Le manuel du propriétaire

Titan 0533423C Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents