Makita LS1040 Le manuel du propriétaire

Marque: Makita

Modèle: LS1040

Catégorie: Scies à onglet

Taper: Le manuel du propriétaire

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

WARNING:

For your personal safety, READ and UNDERSTAND before using.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

AVERTISSEMENT:

Pour votre propre sécurité, prière de lire attentivement avant l’utilisation.

GARDER CES INSTRUCTIONS POUR RÉFÉRENCE ULTÉRIEURE.

ADVERTENCIA:

Para su seguridad personal, LEA DETENIDAMENTE este manual antes de usar la herramienta.

GUARDE ESTAS INSTRUCCIONES PARA FUTURA REFERENCIA.

Compound Miter Saw

Scie Multi Coupe

Ingleteadora telescópica

LS1040

001854

DOUBLE INSULATION

DOUBLE ISOLATION

DOBLE AISLAMIENTO

ENGLISH

SPECIFICATIONS

Model ................................................................................................................................................................... LS1040

Blade diameter............................................................................................................................................ 255 mm (10”)

Hole diameter.......................................................................................................................................... 15.88 mm (5/8”)

Max. Miter angle ................................................................................................................................ Left 45° , Right 52°

Max. Bevel angle.................................................................................................................................................. Left 45°

Max. Cutting capacities (H x W)

No load speed (RPM) ......................................................................................................................................4,600/min.

Dimensions (L x W x H) ..................................................................................................... 530 mm x 476 mm x 532 mm

(20-27/32” x 18-23/32” x 20-15/16”)

Net weight.............................................................................................................................................11.0 kg (24.2 lbs)

• Due to our continuing programme of research and development, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

For Your Own Safety Read Instruc-

tion Manual Before Operating Tool

Save it for future reference

GENERAL SAFETY PRECAUTIONS

USA007-2

(For All Tools)

1. KNOW YOUR POWER TOOL. Read the owner’s

manual carefully. Learn the tool’s applications

and limitations, as well as the specific potential

hazards peculiar to it.

2. KEEP GUARDS IN PLACE and in working order.

3. REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that keys and

adjusting wrenches are removed from tool

before turning it on.

4. KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

5. DON’T USE IN DANGEROUS ENVIRONMENT.

Don’t use power tools in damp or wet locations,

or expose them to rain. Keep work area well

lighted. Don’t use tool in presence of flammable

liquids or gases.

6. KEEP CHILDREN AWAY. All visitors should be

kept safe distance from work area.

7. MAKE WORKSHOP KID PROOF with padlocks,

master switches, or by removing starter keys.

8. DON’T FORCE TOOL. It will do the job better and

safer at the rate for which it was designed.

9. USE RIGHT TOOL. Don’t force tool or attachment

to do a job for which it was not designed.

10. WEAR PROPER APPAREL. Do not wear loose

clothing, gloves, neckties, rings, bracelets, or

other jewelry which may get caught in moving

parts. Nonslip footwear is recommended. Wear

protective hair covering to contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also use face

or dust mask if cutting operation is dusty. Every-

day eyeglasses only have impact resistant

lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold

work when practical. It’s safer than using your

hand and it frees both hands to operate tool.

13. DON’T OVERREACH. Keep proper footing and

balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for best and safest performance. Fol-

low instructions for lubricating and changing

accessories.

Bevel angle

Miter angle

0° 45° (left and right)

0°

90.5 mm x 95 mm

(3-9/16” x 3-3/4”)

69 mm x 130 mm

(2-3/4” x 5-1/8”)

90.5 mm x 67 mm

(3-9/16” x 2-5/8”)

69 mm x 92 mm

(2-3/4” x 3-5/8”)

45° (left)

48 mm x 95 mm

(1-7/8” x 3-3/4”)

35 mm x 130 mm

(1-3/8” x 5-1/8”)

48 mm x 67 mm

(1-7/8” x 2-5/8”)

35 mm x 92 mm

(1-3/8” x 3-5/8”)

15. DISCONNECT TOOLS before servicing; when

changing accessories such as blades, bits, cut-

ters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL START-

ING. Make sure switch is in off position before

plugging in.

17. USE RECOMMENDED ACCESSORIES. Consult

the owner’s manual for recommended accesso-

ries. The use of improper accessories may cause

risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the cutting tool is

unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use of

the tool, a guard or other part that is damaged

should be carefully checked to determine that it

will operate properly and perform its intended

function - check for alignment of moving parts,

binding of moving parts, breakage of parts,

mounting, and any other conditions that may

affect its operation. A guard or other part that is

damaged should be properly repaired or

replaced.

20. DIRECTION OF FEED. Feed work into a blade or

cutter against the direction of rotation of the

blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it

comes to a complete stop.

22. REPLACEMENT PARTS. When servicing use

only identical replacement parts.

23. POLARIZED PLUGS. To reduce the risk of elec-

tric shock, this equipment has a polarized plug

(one blade is wider than the other). This plug will

fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If

it still does not fit, contact a qualified electrician

to install the proper outlet. Do not change the

plug in any way.

VOLTAGE WARNING: Before connecting the tool to a

power source (receptacle, outlet, etc.) be sure the volt-

age supplied is the same as that specified on the name-

plate of the tool. A power source with voltage greater

than that specified for the tool can result in SERIOUS

INJURY to the user – as well as damage to the tool. If in

doubt, DO NOT PLUG IN THE TOOL. Using a power

source with voltage less than the nameplate rating is

harmful to the motor.

USE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to

carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss of

power and overheating. Table 1 shows the correct size to

use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gage. The smaller

the gage number, the heavier the cord.

ADDITIONAL SAFETY RULES

USB037-2

DO NOT let comfort or familiarity with

product (gained from repeated use)

replace strict adherence to miter saw

safety rules. If you use this tool unsafely

or incorrectly, you can suffer serious per-

sonal injury.

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid con-

tact with any coasting blade. It can still cause

severe injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before

each use. Do not operate saw if blade guard

does not move freely and close instantly. Never

clamp or tie the blade guard into the open posi-

tion.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the

turn base and guide fence with a vise during all

operations. Never use your hand to secure the

workpiece.

5. Never reach around saw blade.

6. Turn off tool and wait for saw blade to stop

before moving workpiece or changing settings.

7. Unplug tool before changing blade or servicing.

Table 1. Minimum gage for cord

Ampere Rating

Volts Total length of cord in feet

120 V 25 ft. 50 ft. 100 ft. 150 ft.

More Than Not More Than AWG

0 6 18 16 16 14

6 10 18161412

10 12 16 16 14 12

12 16 14 12 Not Recommended

8. Always secure all moving portions before carry-

ing the tool.

9. Do not use the tool in the presence of flammable

liquids or gases.

10. Check the blade carefully for cracks or damage

before operation. Replace cracked or damaged

blade immediately. Gum and wood pitch hardened

on blades slows saw and increases potential for

kickback. Keep blade clean by first removing it from

tool, then cleaning it with gum and pitch remover, hot

water or kerosene. Never use gasoline to clean

blade.

11. Use only flanges specified for this tool.

12. Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt. Dam-

age to these parts could result in blade break-

age.

13. Make sure that the turn base is properly secured

so it will not move during operation. Use the

holes in the base to fasten the saw to a stable

work platform or bench. NEVER use tool where

operator positioning would be awkward.

14. For your safety, remove the chips, small pieces,

etc. from the table top before operation.

15. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

16. Make sure the shaft lock is released before the

switch is turned on.

17. Be sure that the blade does not contact the turn

base in the lowest position.

18. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

19. Make sure the blade is not contacting the work-

piece before the switch is turned on.

20. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

21. Wait until the blade attains full speed before cut-

ting.

22. Stop operation immediately if you notice any-

thing abnormal.

23. Do not attempt to lock the trigger in the on posi-

tion.

24. Be alert at all times, especially during repetitive,

monotonous operations. Do not be lulled into a

false sense of security. Blades are extremely

unforgiving.

25. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

26. NEVER hold workpiece on right side of blade

with left hand or vice versa. This is called cross-

armed cutting and exposes user to risk of SERI-

OUS PERSONAL INJURY as shown in the figure.

ALWAYS use vise to secure workpiece.

27. Do not abuse cord. Never yank cord to discon-

nect it from the receptacle. Keep cord away from

heat, oil, water and sharp objects.

28. NEVER stack workpieces on the table top to

speed cutting operations. Cut only one piece at a

time.

29. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation

and skin contact. Follow material supplier safety

data.

SAVE THESE INSTRUCTIONS

WARNING:

MISUSE or failure to follow the safety

rules stated in this instruction manual

may cause serious personal injury.

INSTALLATION

Installing auxiliary plate

Installing the auxiliary plate using the notch in the tool’s

base and secure it by tightening the hex bolt.

1. Auxiliary plate

2. Hex bolt

3. Base

001855

Bench mounting

When the tool is shipped, the handle is locked in the low-

ered position by the stopper pin. Release the stopper pin

by lowering the handle slightly and pulling the stopper

pin.

This tool should be bolted with two bolts to a level and

stable surface using the bolt holes provided in the tool’s

base. This will help prevent tipping and possible personal

injury.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on

the tool.

Blade guard

When lowering the handle, the blade guard rises auto-

matically. The guard is spring loaded so it returns to its

original position when the cut is completed and the han-

dle is raised. NEVER DEFEAT OR REMOVE THE

BLADE GUARD OR THE SPRING WHICH ATTACHES

TO THE GUARD.

In the interest of your personal safety, always maintain

the blade guard in good condition. Any irregular opera-

tion of the blade guard should be corrected immediately.

Check to assure spring loaded return action of guard.

NEVER USE THE TOOL IF THE BLADE GUARD OR

SPRING ARE DAMAGED, FAULTY OR REMOVED.

DOING SO IS HIGHLY DANGEROUS AND CAN CAUSE

SERIOUS PERSONAL INJURY.

If the see-through blade guard becomes dirty, or sawdust

adheres to it in such a way that the blade and/or work-

piece is no longer easily visible, unplug the saw and

clean the guard carefully with a damp cloth. Do not use

solvents or any petroleum-based cleaners on the plastic

guard.

If the blade guard is especially dirty and vision through

the guard is impaired, use the supplied socket wrench to

loosen the hex bolt holding the center cover. Loosen the

hex bolt by turning it counterclockwise and raise the

blade guard and center cover. With the blade guard so

positioned, cleaning can be more completely and effi-

ciently accomplished. When cleaning is complete,

reverse procedure above and secure bolt. Do not remove

spring holding blade guard. If guard becomes discolored

through age or UV light exposure, contact a Makita ser-

vice center for a new guard. DO NOT DEFEAT OR

REMOVE GUARD.

1. Auxiliary plate

2. Base

3. Hex bolt

4. Nut

1. Stopper pin

1. Bolt

001832

001792

001856

1. Blade guard

001860

001782

Kerf board

This tool is provided with the kerf board in the turn base

to minimize tearing on the exit side of a cut. If the kerf

groove has not yet been cut in the kerf board by the fac-

tory, you should cut the groove before actually using the

tool to cut a workpiece. Switch on the tool and lower the

blade gently to cut a groove in the kerf board.

Maintaining maximum cutting capacity

This tool is factory adjusted to provide the maximum cut-

ting capacity for a 255 mm (10”) saw blade.

When installing a new blade, always check the lower limit

position of the blade and if necessary, adjust it as follows:

First, unplug the tool. Lower the handle completely. Use

the socket wrench to turn the adjusting bolt until the

periphery of the blade extends slightly below the top sur-

face of the turn base at the point where the front face of

the guide fence meets the top surface of the turn base.

With the tool unplugged, rotate the blade by hand while

holding the handle all the way down to be sure that the

blade does not contact any part of the lower base. Re-

adjust slightly, if necessary.

CAUTION:

• After installing a new blade, always be sure that the

blade does not contact any part of the lower base

when the handle is lowered completely. Always do

this with the tool unplugged.

Adjusting the miter angle

Loosen the grip by turning counterclockwise. Turn the

turn base while pressing down the lock lever. When you

have moved the grip to the position where the pointer

points to the desired angle on the miter scale, securely

tighten the grip clockwise.

CAUTION:

• When turning the turn base, be sure to raise the

handle fully.

• After changing the miter angle, always secure the

turn base by tightening the grip firmly.

Adjusting the bevel angle

To adjust the bevel angle, loosen the lever at the rear of

the tool counterclockwise.

Push the handle to the left to tilt the saw blade until the

pointer points to the desired angle on the bevel scale.

Then tighten the lever clockwise firmly to secure the arm.

1. Kerf board

2. Turn base

1. Socket wrench

2. Adjusting bolt

1. Top surface of

turn base

2. Periphery of

blade

3. Guide fence

002256

002257

001540

1. Pointer

2. Lock lever

3. Grip

4. Miter scale

1. Lever

2. Bevel scale

3. Pointer

001778

001864

001865

CAUTION:

• When tilting the saw blade, be sure to raise the

handle fully.

• After changing the bevel angle, always secure the

arm by tightening the lever clockwise.

Switch action

CAUTION:

• Before plugging in the tool, always check to see

that the switch trigger actuates properly and returns

to the “OFF” position when released.

• When not using the tool, remove the lock-off button

and store it in a secure place. This prevents

unauthorized operation.

• Do not pull the switch trigger hard without pressing

in the lock-off button. This can cause switch

breakage.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided. To start the tool,

press in the lock-off button and pull the switch trigger.

Release the switch trigger to stop.

WARNING:

• NEVER use tool without a fully operative switch

trigger. Any tool with an inoperative switch is

HIGHLY DANGEROUS and must be repaired

before further usage.

• For your safety, this tool is equipped with a lock-off

button which prevents the tool from unintended

starting. NEVER use the tool if it runs when you

simply pull the switch trigger without pressing the

lock-off button. Return tool to a Makita service

center for proper repairs BEFORE further usage.

• NEVER tape down or defeat purpose and function

of lock-off button.

Electric brake

This tool is equipped with an electric blade brake. If the

tool consistently fails to quickly stop blade after switch

trigger release, have tool serviced at a Makita service

center.

The blade brake system is not a substitute for blade

guard. NEVER USE TOOL WITHOUT A FUNCTIONING

BLADE GUARD. SERIOUS PERSONAL INJURY CAN

RESULT.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing saw blade

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

• Use only the Makita socket wrench provided to

install or remove the blade. Failure to do so may

result in overtightening or insufficient tightening of

the hex bolt. This could cause an injury.

Lock the handle in the raised position by pushing in the

stopper pin.

To remove the blade, use the socket wrench to loosen

the hex bolt holding the center cover by turning it coun-

terclockwise. Raise the blade guard and center cover.

Press the shaft lock to lock the spindle and use the

socket wrench to loosen the hex bolt clockwise. Then

remove the hex bolt, outer flange and blade.

To install the blade, mount it carefully onto the spindle,

making sure that the direction of the arrow on the surface

1. Lock-off button

2. Switch trigger

001862

1. Stopper pin

1. Center cover

2. Socket wrench

3. Hex bolt

4. Blade guard

1. Socket wrench

2. Shaft lock

001792

001858

001859

of the blade matches the direction of the arrow on the

blade case.

Install the outer flange and hex bolt, and then use the

socket wrench to tighten the hex bolt (left-handed)

securely counterclockwise while pressing the shaft lock.

Return the blade guard and center cover to its original

position. Then tighten the hex bolt clockwise to secure

the center cover. Release the handle from the raised

position by pulling the stopper pin. Lower the handle to

make sure that the blade guard moves properly. Make

sure shaft lock has released spindle before making cut.

Dust bag

The use of the dust bag makes cutting operations clean

and dust collection easy. To attach the dust bag, fit it onto

the dust nozzle.

When the dust bag is about half full, remove the dust bag

from the tool and pull the fastener out. Empty the dust

bag of its contents, tapping it lightly so as to remove par-

ticles adhering to the insides which might hamper further

collection.

NOTE:

• If you connect a vacuum cleaner to your saw, more

efficient and cleaner operations can be performed.

Securing workpiece

WARNING:

• It is extremely important to always secure the

workpiece properly and tightly with the vise. Failure

to do so can cause the tool to be damaged and/or

the workpiece to be destroyed. PERSONAL

INJURY MAY ALSO RESULT. Also, after a cutting

operation, DO NOT raise the blade until the blade

has come to a complete stop.

CAUTION:

• When cutting long workpieces, use supports that

are as high as the top surface level of the turn base.

Do not rely solely on the vertical vise and/or

horizontal vise to secure the workpiece.

Thin material tends to sag. Support workpiece over

its entire length to avoid blade pinch and possible

KICKBACK.

Sub-fence

This tool is equipped with the sub-fence which should

ordinarily be positioned as shown in the figure.

However, when performing left bevel cuts, set it to the left

position as shown in the figure.

CAUTION:

• When performing left bevel cuts, flip the fence over

to the left position as shown in the figure.

1. Hex bolt

2. Outer flange

3. Saw blade

4. Inner flange

5. Spindle

1. Blade case

2. Arrow

3. Saw blade

4. Arrow

1. Dust nozzle

2. Dust bag

3. Fastener

12 4

001786

2 1 4 3

001787

001861

1. Support

2. Turn base

1. Sub-fence

001549

001766

Otherwise, it will contact the blade or a part of the

tool, causing possible serious injury to the operator.

Vertical vise

The vertical vise can be installed in two positions on

either the left or right side of the guide fence or the holder

assembly (optional accessory). Insert the vise rod into

the hole in the guide fence or the holder assembly and

tighten the screw to secure the vise rod.

Position the vise arm according to the thickness and

shape of the workpiece and secure the vise arm by tight-

ening the screw. If the screw to secure the vise arm con-

tacts the guide fence, install the screw on the opposite

side of vise arm. Make sure that no part of the tool con-

tacts the vise when lowering the handle all the way. If

some part contacts the vise, re-position the vise.

Press the workpiece flat against the guide fence and the

turn base. Position the workpiece at the desired cutting

position and secure it firmly by tightening the vise knob.

CAUTION:

• The workpiece must be secured firmly against the

turn base and guide fence with the vise during all

operations.

Horizontal vise (optional accessory)

The horizontal vise can be installed in two positions on

either the left or right side of the base. When performing

15° or greater miter cuts, install the horizontal vise on the

side opposite the direction in which the turn base is to be

turned.

By turning the vise knob counterclockwise, the screw is

released and the vise shaft can be moved rapidly in and

out. By turning the vise knob clockwise, the screw

remains secured. To grip the workpiece, turn the vise

knob gently clockwise until the projection reaches its top-

most position, then fasten securely. If the vise knob is

forced in or pulled out while being turned clockwise, the

projection may stop at an angle. In this case, turn the

vise knob back counterclockwise until the screw is

released, before turning again gently clockwise.

The maximum width of the workpiece which can be

secured by the horizontal vise is 130 mm (5-1/8”).

CAUTION:

• Grip the workpiece only when the projection is at

the topmost position. Failure to do so may result in

insufficient securing of the workpiece. This could

cause the workpiece to be thrown, cause damage

to the blade or cause the loss of control, which can

result in PERSONAL INJURY.

Holders and holder assembly

(optional accessories)

The holders and the holder assembly can be installed on

either side as a convenient means of supporting work-

pieces horizontally. Install them as shown in the figure.

Then tighten the screws firmly to secure the holders and

the holder assembly.

When cutting long workpieces, use the holder-rod

assembly (optional accessory). It consists of two holder

assemblies and two rods 12.

1. Sub-fence

1. Vise arm

2. Vise rod

3. Guide fence

4. Holder

5. Holder assem-

bly

6. Vise knob

7. Screw

1. Vise knob

2. Projection

3. Vise shaft

4. Base

001767

001796

001807

1. Holder

2. Holder assem-

bly

1. Holder assem-

bly

2. Rod 12

002247

002246

CAUTION:

• Always support long workpieces level with the top

surface of the turn base for accurate cuts and to

prevent dangerous loss of control of the tool.

OPERATION

CAUTION:

• Before use, be sure to release the handle from the

lowered position by pulling the stopper pin.

• Make sure the blade is not contacting the

workpiece, etc. before the switch is turned on.

• Do not apply excessive pressure on the handle

when cutting. Too much force may result in

overload of the motor and/or decreased cutting

efficiency. Push down handle with only as much

force as is necessary for smooth cutting and

without significant decrease in blade speed.

• Gently press down the handle to perform the cut. If

the handle is pressed down with force or if lateral

force is applied, the blade will vibrate and leave a

mark (saw mark) in the workpiece and the precision

of the cut will be impaired.

1. Press cutting

Secure the workpiece with the vise. Switch on the

tool without the blade making any contact and wait

until the blade attains full speed before lowering.

Then gently lower the handle to the fully lowered

position to cut the workpiece. When the cut is com-

pleted, switch off the tool and WAIT UNTIL THE

BLADE HAS COME TO A COMPLETE STOP

before returning the blade to its fully elevated posi-

tion.

2. Miter cutting

Refer to the previously covered “Adjusting the miter

angle”.

3. Bevel cut

Loosen the lever and tilt the saw blade to set the

bevel angle (Refer to the previously covered

“Adjusting the bevel angle”). Be sure to retighten

the lever firmly to secure the selected bevel angle

safely. Secure the workpiece with a vise. Switch on

the tool without the blade making any contact and

wait until the blade attains full speed. Then gently

lower the handle to the fully lowered position while

applying pressure in parallel with the blade. When

the cut is completed, switch off the tool and WAIT

UNTIL THE BLADE HAS COME TO A COMPLETE

STOP before returning the blade to its fully elevated

position.

CAUTION:

• Always be sure that the blade will move down to

bevel direction during a bevel cut. Keep hands out

of path of saw blade.

• During a bevel cut, it may create a condition

whereby the piece cut off will come to rest against

the side of the blade. If the blade is raised while the

blade is still rotating, this piece may be caught by

the blade, causing fragments to be scattered which

is dangerous. The blade should be raised ONLY

after the blade has come to a complete stop.

• When pressing the handle down, apply pressure

parallel to the blade. If the pressure is not parallel to

the blade during a cut, the angle of the blade might

be shifted and the precision of the cut will be

impaired.

• Always set the sub-fence to the left position when

performing left bevel cuts.

4. Compound cutting

Compound cutting is the process in which a bevel

angle is made at the same time in which a miter

angle is being cut on a workpiece. Compound cut-

ting can be performed at angle shown in the table.

When performing compound cutting, refer to “Press

cutting”, “Miter cutting” and “Bevel cut” explana-

tions.

001788

001868

Miter angle

Bevel angle

Left and Right 0˚ - 45˚

45˚

006366

5. Cutting crown and cove moldings

Crown and cove moldings can be cut on a com-

pound miter saw with the moldings laid flat on the

turn base.

There are two common types of crown moldings

and one type of cove moldings; 52/38° wall angle

crown molding, 45° wall angle crown molding and

45° wall angle cove molding. See illustrations.

There are crown and cove molding joints which are

made to fit “Inside” 90° corners ((1) and (2) in Fig.

A) and “Outside” 90° corners ((3) and (4) in Fig. A).

Measuring

Measure the wall length and adjust workpiece on

table to cut wall contact edge to desired length.

Always make sure that cut workpiece length at the

back of the workpiece is the same as wall length.

Adjust cut length for angle of cut. Always use sev-

eral pieces for test cuts to check the saw angles.

When cutting crown and cove moldings, set the

bevel angle and miter angle as indicated in the

table (A) and position the moldings on the top sur-

face of the saw base as indicated in the table (B).

Example:

In the case of cutting 52/38° type crown

molding for position (1) in Fig. A:

• Tilt and secure bevel angle setting to

33.9° LEFT.

• Adjust and secure miter angle setting to

31.6° RIGHT.

• Lay crown molding with its broad back

(hidden) surface down on the turn base

with its CEILING CONTACT EDGE

against the guide fence on the saw.

• The finished piece to be used will

always be on the LEFT side of the blade

after the cut has been made.

1. 52/38° type

crown molding

2. 45° type crown

molding

3. 45° type cove

molding

1. Inside corner

2. Outside corner

1. Inside corner

2. Outside corner

52∞

38∞

45∞

123

001555

(1) (2) (3) (4)

1 2

Fig.A

001556

(1)

(2)

(1)

(2)

(1)

(2)

(1)

(2)

(3)

(4)

001557

(1)

(2)

(3)

(4)

Molding

position in

Fig. A

Bevel angle Miter angle

For outside

corner

For inside

corner

52/38˚ type

45˚ type

Right 31.6˚

45˚ type

Left 33.9˚ Left 30˚

52/38˚ type

Left 31.6˚

Right 31.6˚

Left 35.3˚

Right 35.3˚

Table (A)

006361

Molding

position in

Fig. A

Molding edge against

guide fence

Finished piece

(1)

Ceiling contact edge should

be against guide fence.

(2)

(3)

(4)

Ceiling contact edge should

be against guide fence.

For

outside

corner

Finished piece

will be on the

Left side of

blade.

Finished piece

will be on the

Right side of

blade.

For inside

corner

Wall contact edge should be

against guide fence.

Table (B)

006362

EN0002-1

Compound Miter Saw

Miter and Bevel Angle Settings

000031

Ceiling

Wall

Wall to Crown Molding Angle: 52/38 degrees

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

43.0 46.8 101 30.1 26.9 141 15.3 12.3

61 42.8 46.3 102 29.7 26.5 142 14.9 12.0

62 42.5 45.7 103 29.4 26.1 143 14.5 11.6

63 42.2 45.1 104 29.0 25.7 144 14.1 11.3

64 41.9 44.6 105 28.7 25.3 145 13.7 11.0

65 41.7 44.0 106 28.3 24.9 146 13.3 10.7

66 41.4 43.5 107 28.0 24.5 147 12.9 10.3

67 41.1 42.9 108 27.6 24.1 148 12.5 10.0

68 40.8 42.4 109 27.2 23.7 149 12.2 9.7

69 40.5 41.9 110 26.9 23.3 150 11.8 9.4

70 40.2 41.3 111 26.5 22.9 151 11.4 9.0

71 39.9 40.8 112 26.1 22.6 152 11.0 8.7

72 39.6 40.3 113 25.8 22.2 153 10.8 8.4

73 39.3 39.8 114 25.4 21.8 154 10.2 8.1

74 39.0 39.2 115 25.0 21.4 155 9.8 7.8

75 38.7 38.7 116 24.7 21.0 156 9.4 7.5

76 38.4 38.2 117 24.3 20.7 157 9.0 7.1

77 38.1 37.7 118 23.9 20.3 158 8.6 6.8

78 37.8 37.2 119 23.6 19.9 159 8.3 6.5

79 37.4 36.8

120

23.2 19.6 160 7.9 6.2

80 37.1 36.3 121 22.8 19.2 161 7.5 5.9

81 36.8 35.8 122 22.5 18.8 162 7.1 5.6

82 36.5 35.3 123 22.1 18.5 163 6.7 5.3

83 36.2 34.8 124 21.7 18.1 164 6.3 4.9

84 35.8 34.4 125 21.3 17.8 165 5.9 4.6

85 35.5 33.9 126 21.0 17.4 166 5.5 4.3

86 35.2 33.4 127 20.6 17.1 167 5.1 4.0

87 34.9 33.0 128 20.2 16.7 168 4.7 3.7

88 34.5 32.5 129 19.8 16.4 169 4.3 3.4

89 34.2 32.1 130 19.5 16.0 170 3.9 3.1

33.9 31.6 131 19.1 15.7 171 3.5 2.8

91 33.5 31.2 132 18.7 15.3 172 3.2 2.5

92 33.2 30.7 133 18.3 15.0 173 2.8 2.2

93 32.8 30.3 134 17.9 14.6 174 2.4 1.8

94 32.5 29.9 135 17.6 14.3 175 2.0 1.5

95 32.2 29.4 136 17.2 14.0 176 1.6 1.2

96 31.8 29.0 137 16.8 13.6 177 1.2 0.9

97 31.5 28.6 138 16.4 13.3 178 0.8 0.6

98 31.1 28.2 139 16.0 13.0 179 0.4 0.3

99 30.8 27.7 140 15.8 12.8 180 0.0 0.0

100 30.4 27.3

EN0003-1

Compound Miter Saw

Miter and Bevel Angle Settings

000032

Ceiling

Wall

Wall to Crown Molding Angle: 45 degrees

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

Wall Angle

(deg.)

Bevel Angle

(deg.)

Miter Angle

(deg.)

37.8 50.8 101 26.7 30.2 141 13.7 14.1

61 37.5 50.2 102 26.4 29.8 142 13.3 13.7

62 37.3 49.6 103 26.1 29.4 143 13.0 13.3

63 37.1 49.1 104 25.8 28.9 144 12.6 12.9

64 36.8 48.5 105 25.5 28.5 145 12.3 12.6

65 36.6 48.0 106 25.2 28.1 146 11.9 12.2

66 36.4 47.4 107 24.9 27.6 147 11.6 11.8

67 36.1 46.9 108 24.6 27.2 148 11.2 11.5

68 35.9 46.4 109 24.2 26.8 149 10.9 11.1

69 35.6 45.8 110 23.9 26.3 150 10.5 10.7

70 35.4 45.3 111 23.6 25.9 151 10.2 10.4

71 35.1 44.8 112 23.3 25.5 152 9.8 10.0

72 34.9 44.2 113 23.0 25.1 153 9.5 9.6

73 34.6 43.7 114 22.7 24.7 154 9.2 9.3

74 34.4 43.2 115 22.3 24.3 155 8.8 8.9

75 34.1 42.7 116 22.0 23.8 156 8.5 8.5

76 33.9 42.1 117 21.7 23.4 157 8.1 8.2

77 33.6 41.6 118 21.4 23.0 158 7.8 7.8

78 33.3 41.1 119 21.0 22.6 159 7.4 7.5

79 33.1 40.6

120

20.7 22.2 160 7.1 7.1

80 32.8 40.1 121 20.4 21.8 161 6.7 6.7

81 32.5 39.6 122 20.0 21.4 162 6.4 6.4

82 32.3 39.1 123 19.7 21.0 163 6.0 6.0

83 32.0 38.6 124 19.4 20.6 164 5.6 5.7

84 31.7 38.1 125 19.1 20.2 165 5.3 5.3

85 31.4 37.7 126 18.7 19.8 166 4.9 5.0

86 31.1 37.2 127 18.4 19.4 167 4.6 4.6

87 30.9 36.7 128 18.1 19.0 168 4.2 4.3

88 30.6 36.2 129 17.7 18.6 169 3.9 3.9

89 30.3 35.7 130 17.4 18.2 170 3.5 3.5

30.0 35.3 131 17.1 17.9 171 3.2 3.2

91 29.7 34.8 132 16.7 17.5 172 2.8 2.8

92 29.4 34.3 133 16.4 17.1 173 2.5 2.5

93 29.1 33.9 134 16.0 16.7 174 2.1 2.1

94 28.8 33.4 135 15.7 16.3 175 1.8 1.8

95 28.5 32.9 136 15.4 15.9 176 1.4 1.4

96 28.2 32.5 137 15.0 15.6 177 1.1 1.1

97 27.9 32.0 138 14.7 15.2 178 0.7 7.0

98 27.6 31.6 139 14.3 14.8 179 0.4 0.4

99 27.3 31.1 140 14.0 14.4 180 0.0 0.0

100 27.0 30.7

Crown molding stoppers (optional accessories)

allow easier cuts of crown molding without tilting the

saw blade. Install them on the base as shown in the

figures.

Position crown molding with its WALL CONTACT

EDGE against the guide fence and its CEILING

CONTACT EDGE against the crown molding stop-

pers as shown in the figure. Adjust the crown mold-

ing stoppers according to the size of the crown

molding. Tighten the screws to secure the crown

molding stoppers. Refer to the table (C) for the

miter angle.

6. Cutting aluminum extrusion

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in the figure to

prevent deformation of the aluminum. Use a cutting

lubricant when cutting the aluminum extrusion to

prevent build-up of the aluminum material on the

blade.

CAUTION:

• Never attempt to cut thick or round aluminum

extrusions. Thick aluminum extrusions may come

loose during operation and round aluminum

extrusions cannot be secured firmly with this tool.

7. Wood facing

Use of wood facing helps to assure splinter-free

cuts in workpieces. Attach a wood facing to the

guide fence using the holes in the guide fence.

See the figure concerning the dimensions for a sug-

gested wood facing.

CAUTION:

• Use straight wood of even thickness as the wood

facing.

• Use screws to attach the wood facing to the guide

fence. The screws should be installed so that the

screw heads are below the surface of the wood

facing.

• When the wood facing is attached, do not turn the

turn base with the handle lowered. The blade and/

or the wood facing will be damaged.

8. Cutting repetitive lengths

When cutting several pieces of stock to the same

length, ranging from 240 mm (9-29/64”) to 400 mm

(15-3/4”), use of the set plate (optional accessory)

will facilitate more efficient operation. Install the set

plate on the holder (optional accessory) as shown

in the figure.

Align the cutting line on your workpiece with either

the left or right side of the groove in the kerf board,

1. Crown molding

stopper L

2. Crown molding

stopper R

3. Base

1. Guide fence

2. Crown molding

3. Crown molding

stopper

4. Screw

1. Vise

2. Spacer block

3. Guide fence

4. Aluminum extru-

sion

5. Spacer block

001789

3 4

001560

Position in

Fig.A

Miter angle Finished piece

(1) Right

45˚

Save the right side of blade

(2)

Save the left side of blade

(3)

Save the right side of blade

(4) Right

45˚

Save the left side of blade

Left

45˚

For inside

corner

For outside

corner

Table (C)

006365

001844

1. Hole

1. Set plate

2. Holder

3. Screw

Over 10mm (3/8”)

Over 460mm (18-1/8”)

90mm

(3-9/16”)

25mm

(1”)

90mm

(3-9/16”)

107mm

(4-7/32”)

90mm

(3-9/16”)

107mm

(4-7/32”)

001790

001846

and while holding the workpiece from moving, move

the set plate flush against the end of the workpiece.

Then secure the set plate with the screw. When the

set plate is not used, loosen the screw and turn the

set plate out of the way.

NOTE:

• Use of the holder-rod assembly (optional

accessory) allows cutting repetitive lengths up to

2,200 mm (7.2 ft.) approximately.

Carrying tool

Make sure that the tool is unplugged. Secure the blade at

0° bevel angle and the turn base at left miter angle fully.

Lower the handle fully and lock it in the lowered position

by pushing in the stopper pin.

Carry the tool by carrying grip as shown in the figure. If

you remove the holders, dust bag, etc., you can carry the

tool more easily.

CAUTION:

• Always secure all moving portions before carrying

the tool.

• Stopper pin is for carrying and storage purposes

only and not for any cutting operations.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

WARNING:

• Always be sure that the blade is sharp and clean for

the best and safest performance.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1. Miter angle

Loosen the grip which secures the turn base. Turn

the turn base so that the pointer points to 0° on the

miter scale. Tighten the grip and loosen the hex

bolts securing the guide fence using the socket

wrench.

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Square the

side of the blade with the face of the guide fence

using a triangular rule, try-square, etc. Then

securely tighten the hex bolts on the guide fence in

the order from the right side.

2. Bevel angle

(1) 0° bevel angle

Lower the handle fully and lock it in the low-

ered position by pushing in the stopper pin.

Loosen the lever at the rear of the tool.

Loosen the hex nut and turn the 0° bevel

angle adjusting bolt on the right side of the

arm two or three revolutions clockwise to tilt

the blade to the right.

1. Stopper pin

001792

001774

1. Hex bolt

1. Triangular rule

2. Grip

3. Guide fence

1. Arm

2. Lever

3. 0° adjusting bolt

4. Hex nut

002258

002259

001768

Carefully square the side of the blade with the

top surface of the turn base using the triangu-

lar rule, try-square, etc. by turning the 0°

bevel angle adjusting bolt counterclockwise.

Then tighten the hex nut to secure the 0°

bevel angle adjusting bolt and tighten the

lever securely.

Make sure that the pointer on the turn base

point to 0° on the bevel scale on the arm. If it

does not point to 0°, loosen the screw which

secures the pointer and adjust the pointer so

that it will point to 0°.

(2) 45° bevel angle

Adjust the 45° bevel angle only after perform-

ing 0° bevel angle adjustment. To adjust left

45° bevel angle, loosen the lever and tilt the

blade to the left fully. Make sure that the

pointer on the arm points to 45° on the bevel

scale on the arm holder. If the pointer does

not point to 45°, turn the 45° bevel angle

adjusting bolt on the left side of the arm until

the pointer points to 45°.

Replacing carbon brushes

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

After replacing brushes, plug in the tool and break in

brushes by running tool with no load for about 10 min-

utes. Then check the tool while running and electric

brake operation when releasing the switch trigger. If elec-

tric brake is not working well, ask your local Makita ser-

vice center for repair.

After use

• After use, wipe off chips and dust adhering to the

tool with a cloth or the like. Keep the blade guard

clean according to the directions in the previously

covered section titled “Blade guard”. Lubricate the

sliding portions with machine oil to prevent rust.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized or Factory Service Centers,

always using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.

1. Triangular rule

2. Saw blade

3. Top surface of

turn base

1. Arm

2. Bevel scale

3. Pointer

4. Turn base

1. Lever

2. Arm

3. Pointer

4. 45° bevel angle

adjusting bolt

001819

001769

001770

1. Limit mark

1. Screwdriver

2. Brush holder

cap

001145

001772

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Steel & Carbide-tipped saw blades

• Auxiliary plate

• Vise assembly (Horizontal vise)

• Vertical vise

• Socket wrench 13

• Holder set

• Holder assembly

• Holder rod assembly

• Set plate

• Dust bag

• Crown molding stopper set

• Triangular rule

• Lock-off button (2 pcs.)

EN0006-1

MAKITA LIMITED ONE YEAR WARRANTY

Warranty Policy

Every Makita tool is thoroughly inspected and tested

before leaving the factory. It is warranted to be free of

defects from workmanship and materials for the period of

ONE YEAR from the date of original purchase. Should

any trouble develop during this one year period, return

the COMPLETE tool, freight prepaid, to one of Makita’s

Factory or Authorized Service Centers. If inspection

shows the trouble is caused by defective workmanship or

material, Makita will repair (or at our option, replace)

without charge.

This Warranty does not apply where:

• repairs have been made or attempted by others:

• repairs are required because of normal wear and

tear:

• the tool has been abused, misused or improperly

maintained:

• alterations have been made to the tool.

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAM-

AGES FROM THE SALE OR USE OF THE PRODUCT.

THIS DISCLAIMER APPLIES BOTH DURING AND

AFTER THE TERM OF THIS WARRANTY.

MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED

WARRANTIES, INCLUDING IMPLIED WARRANTIES

OF “MERCHANTABILITY” AND “FITNESS FOR A SPE-

CIFIC PURPOSE,” AFTER THE ONE YEAR TERM OF

THIS WARRANTY.

This Warranty gives you specific legal rights, and you

may also have other rights which vary from state to state.

Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limi-

tation or exclusion may not apply to you. Some states do

not allow limitation on how long an implied warranty lasts,

so the above limitation may not apply to you.

Miter saw blades

For smooth and precise cutting in various materials.

Combination

General purpose blade for fast and smooth rip,

crosscuts and miters.

Crosscutting

For smoother cross grain cuts. Slices cleanly

against the grain.

Fine cross cuts For sand-free cuts cleanly against the grain.

Non-ferrous metals

miter saw blades

For miters in aluminum, copper, brass, tubing,

and other non-ferrous metals.

006526

FRANÇAIS

SPÉCIFICATIONS

Modèle ................................................................................................................................................................. LS1040

Diamètre de la lame.................................................................................................................................... 255 mm (10”)

Diamètre de l’orifice ................................................................................................................................ 15.88 mm (5/8”)

Angle d’onglet max. ....................................................................................................................Gauche 45° , Droite 52°

Angle de biseau max. ....................................................................................................................................Gauche 45°

Capacités de coupe maximales (Hauteur x Largeur)

Vitesse à vide (T/MIN) .....................................................................................................................................4,600/min.

Dimensions (L x L x H)....................................................................................................... 530 mm x 476 mm x 532 mm

(20-27/32” x 18-23/32” x 20-15/16”)

Poids net ...............................................................................................................................................11.0 kg (24.2 lbs)

• Le fabricant se réserve le droit de modifier sans avertissement les spécifications.

• Note: Les spécifications peuvent varier selon les pays.

Pour votre propre sécurité, veuillez

lire le manuel d’instructions avant

d’utiliser l’outil Conservez-le pour

référence ultérieure CONSIGNES

GÉNÉRALES DE SÉCURITÉ

USA007-2

(Pour TOUS LES OUTILS)

1. VOUS DEVEZ CONNAÎTRE VOTRE OUTIL

ÉLECTRIQUE. Lisez attentivement le manuel

d’instructions. Familiarisez-vous avec les

applications et limites de l’outil, ainsi qu’avec

les risques potentiels qui lui sont spécifiques.

2. MAINTENEZ LES PROTECTEURS EN PLACE et

en bon état de fonctionnement.

3. RETIREZ LES CLÉS DE RÉGLAGE ET LES CLÉS.

Prenez l’habitude de vous assurer que les clés et

clés de réglage ont été retirées de l’outil avant de

le mettre sous tension.

4. MAINTENEZ L’AIRE DE TRAVAIL PROPRE. Les

aires de travail et les établis encombrés ouvrent

la porte aux accidents.

5. ÉVITEZ L’UTILISATION DANS UN

ENVIRONNEMENT DANGEREUX. N’utilisez pas

les outils électriques dans les endroits humides

ou mouillés, et ne les exposez pas à la pluie.

Maintenez un éclairage adéquat dans l’aire de

travail. N’utilisez pas l’outil en présence de

liquides ou gaz inflammables.

6. MAINTENEZ LES ENFANTS À L’ÉCART. Toute

autre personne que l’utilisateur de l’outil doit se

tenir à une distance sûre de l’aire de travail.

7. FAITES EN SORTE QUE L’ATELIER SOIT SANS

DANGER POUR LES ENFANTS, en y posant des

cadenas, un interrupteur principal, ou en retirant

des équipements leurs clés de démarrage.

8. NE FORCEZ PAS L’OUTIL. Il effectuera un travail

de meilleure qualité et plus sûr s’il est utilisé au

régime pour lequel il a été conçu.

9. UTILISEZ LE BON OUTIL. Ne forcez pas un outil

ou accessoire à effectuer un travail pour lequel il

n’a pas été conçu.

10. PORTEZ DES VÊTEMENTS ADÉQUATS. Ne

portez ni vêtements ni gants amples, ni cravate,

anneaux, bracelets ou autres bijoux

susceptibles d’être happés par les pièces

mobiles de l’outil. Le port de chaussures

antidérapantes est recommandé. Portez un filet

de protection pour envelopper les cheveux

longs.

11. PORTEZ TOUJOURS DES LUNETTES DE

PROTECTION. Si le travail de coupe dégage de la

poussière, portez également un écran facial ou

Angle de coupe en biseau

Angle de coupe d’onglet

0° 45° (gauche et droite)

0°

90.5 mm x 95 mm

(3-9/16” x 3-3/4”)

69 mm x 130 mm

(2-3/4” x 5-1/8”)

90.5 mm x 67 mm

(3-9/16” x 2-5/8”)

69 mm x 92 mm

(2-3/4” x 3-5/8”)

45° (Gauche)

48 mm x 95 mm

(1-7/8” x 3-3/4”)

35 mm x 130 mm

(1-3/8” x 5-1/8”)

48 mm x 67 mm

(1-7/8” x 2-5/8”)

35 mm x 92 mm

(1-3/8” x 3-5/8”)

un masque antipoussières. Les lunettes

ordinaires ne sont munies que de lentilles

résistances aux chocs ; elles ne constituent PAS

des lunettes de protection.

12. FIXEZ BIEN LA PIÈCE. Lorsque cela est

possible, fixez la pièce à travailler à l’aide de

dispositifs de serrage ou d’un étau. Cela est plus

sécuritaire que l’utilisation de la main et libère

les deux mains pour le maniement de l’outil.

13. MAINTENEZ UNE BONNE POSITION. Assurez-

vous d’une bonne prise au sol et d’une bonne

position d’équilibre en tout temps.

14. PRENEZ SOIN DES OUTILS. Maintenez les outils

bien aiguisés et propres pour assurer une

performance sécuritaire et optimale. Suivez les

instructions de lubrification et de changement

des accessoires.

15. DÉBRANCHEZ LES OUTILS avant tout travail de

réparation ou avant de changer les accessoires

tels que lames, embouts/forets/fraises et

couteaux.

16. RÉDUISEZ LES RISQUES DE MISE EN MARCHE

ACCIDENTELLE. Assurez-vous que

l’interrupteur est en position d’arrêt avant de

brancher l’outil.

17. UTILISEZ LES ACCESSOIRES RECOMMANDÉS.

Consultez le manuel de l’utilisateur pour savoir

quels sont les accessoires recommandés.

L’utilisation d’accessoires non adéquats peut

comporter un risque de blessure.

18. NE VOUS APPUYEZ JAMAIS SUR L’OUTIL. Une

blessure grave peut survenir si l’outil bascule ou

si vous touchez accidentellement l’outil

tranchant.

19. VÉRIFIEZ S’IL Y A DES PIÈCES

ENDOMMAGÉES. Avant d’utiliser l’outil, tout

protecteur ou dispositif endommagé doit être

vérifié soigneusement afin de s’assurer qu’il

fonctionne adéquatement et peut remplir la

fonction pour laquelle il est conçu. Vérifiez si les

pièces mobiles sont bien alignées et bien fixées,

vérifiez la présence de pièces brisées, vérifiez

que l’outil est bien monté et assurez-vous que

rien ne peut entraver son bon fonctionnement.

Un protecteur ou tout autre dispositif

endommagé doit être adéquatement réparé ou

remplacé.

20. SENS D’ALIMENTATION. N’alimentez la lame ou

l’outil tranchant avec la pièce à travailler que

dans le sens opposé à celui de la progression de

la lame ou de l’outil tranchant.

21. NE LAISSEZ JAMAIS SANS SURVEILLANCE UN

OUTIL EN MARCHE. COUPEZ LE CONTACT.

Attendez que l’outil se soit complètement arrêté

avant de le quitter.

22. PIÈCES DE RECHANGE. Seules des pièces de

rechange identiques doivent être utilisées lors

des réparations.

23. FICHES POLARISÉES. Pour réduire les risques

de choc électrique, cet appareil est muni d’une

fiche polarisée (une des broches est plus large

que l’autre). Cette fiche ne peut être insérée

dans une prise polarisée que dans un seul sens.

Si la fiche ne s’insère pas à fond dans la prise,

insérez-la en sens inverse. Si elle ne s’insère

toujours pas à fond, contactez un technicien

qualifié pour faire installer une prise appropriée.

N’apportez aucune modification à la fiche.

MISE EN GARDE RELATIVE À LA TENSION: Avant de

brancher l’outil sur une source d’alimentation (prise ou

autre dispositif), assurez-vous que la tension du circuit

correspond à celle qui est spécifiée sur la plaque

signalétique de l’outil. L’utilisation d’une source

d’alimentation dont la tension est supérieure à celle

spécifiée pour l’outil peut entraîner l’utilisateur à une

GRAVE BLESSURE et endommager l’outil. En cas de

doute, NE BRANCHEZ PAS L’OUTIL. L’utilisation d’une

source d’alimentation dont la tension est inférieure à la

valeur indiquée sur la plaque signalétique endommagera

le moteur.

UTLISEZ UN CORDON PROLONGATEUR ADÉQUAT.

Assurez-vous que le cordon prolongateur est en bon

état. Lors de l’utilisation d’un cordon prolongateur,

utilisez sans faute un cordon assez gros pour conduire le

courant que le produit nécessite. Un cordon trop petit

provoquera une baisse de tension de secteur, résultant

en une perte de puissance et une surchauffe. Le Tableau

1 indique la dimension appropriée de cordon selon sa

longueur et selon l’intensité nominale indiquée sur la

plaque signalétique. En cas de doute sur un cordon

donné, utilisez le cordon suivant (plus gros). Plus le

numéro de gabarit indiqué est petit, plus le cordon est

gros.

Tableau 1. Gabarit minimum du cordon

Intensité nominale

Volts Longueur totale du cordon en pieds

120 V 25 ft. 50 ft. 100 ft. 150 ft.

Plus de Pas plus de Calibre américain des fils

0 6 18 16 16 14

6 10 18161412

10 12 16 16 14 12

12 16 14 12 Non recommandé

RÈGLES DE SÉCURITÉ

SUPPLEMENTAIRES

USB037-2

NE vous laissez PAS tromper (au fil d’une

utilisation répétée) par un sentiment

d’aisance et de familiarité avec le

produit, en négligeant le respect

rigoureux des consignes de sécurité qui

accompagnent la scie à chariot mixte.

L’utilisation non sécuritaire ou incorrecte

de cet outil comporte un risque de

blessure grave.

1. Portez des lunettes de protection.

2. Maintenez les mains hors de la ligne de coupe

de la lame. Évitez tout contact avec la lame

lorsqu’elle continue de tourner après la mise

hors tension de l’outil. Elle peut alors quand

même causer de graves blessures.

3. N’utilisez jamais la scie lorsque les protecteurs

ne sont pas bien en place. Vérifiez le bon

fonctionnement du protecteur de lame avant

chaque utilisation. N’utilisez pas la scie si le

protecteur de lame ne se déplace pas librement

et ne recouvre pas la lame instantanément.

N’immobilisez jamais le protecteur de lame en

position ouverte.

4. N’effectuez aucune opération en tenant la pièce

uniquement avec la main. La pièce doit être fixée

fermement contre le socle rotatif et le garde de

guidage avec un étau lors de toutes les

opérations. N’utilisez jamais la main pour

immobiliser la pièce.

5. N’approchez jamais les mains de la lame.

6. Éteignez l’outil et attendez l’arrêt de la lame

avant de déplacer la pièce ou de modifier les

réglages.

7. Débranchez l’outil avant le changement de lame

ou la réparation.

8. Avant de transporter l’outil, immobilisez d’abord

toutes ses pièces mobiles.

9. N’utilisez pas l’outil en présence de liquides ou

gaz inflammables.

10. Avant l’utilisation, vérifiez toujours

soigneusement l’absence de fissures ou de

dommages sur la lame. Veuillez remplacer

immédiatement toute lame fissurée ou

endommagée. Les dépôts de colle et les copeaux

de bois qui se solidifient sur les lames ralentissent la

scie et entraînent une augmentation des risques de

choc en retour. Pour nettoyer la lame, retirez-la

d’abord de l’outil, puis utilisez un décapant, de l’eau

chaude ou du kérosène pour retirer la colle et les

copeaux. N’utilisez jamais d’essence pour nettoyer

la lame.

11. N’utilisez que les flasques spécifiés pour cet

outil.

12. Prenez garde d’endommager l’arbre, les

flasques (tout particulièrement leur surface

d’installation) ou le boulon. L’endommagement

de ces pièces peut causer une cassure de la

lame.

13. Assurez-vous que le socle rotatif est bien

immobilisé, de sorte qu’il ne bouge pas pendant

le travail de coupe. Fixez la scie à une surface de

travail ou à un établi stable au moyen des

orifices de la base. N’utilisez JAMAIS l’outil si

vous vous trouvez dans une position qui

n’assure pas une pleine liberté de mouvement.

14. Pour votre sécurité, retirez les copeaux et autres

petites pièces présente sur la table avant de

commencer le travail.

15. Évitez les clous. Avant de travailler votre pièce,

inspectez-la et retirez-en tous les clous.

16. Assurez-vous que le verrou de l’arbre est

dégagé avant de mettre l’interrupteur sous

tension.

17. Assurez-vous que la lame n’entre pas en contact

avec le socle rotatif lorsqu’elle se trouve sur sa

position la plus basse.

18. Tenez fermement la poignée. Gardez à l’esprit

que la scie se déplace légèrement vers le haut

ou le bas au démarrage et à l’arrêt.

19. Assurez-vous que la lame n’entre pas en contact

avec la pièce avant de mettre l’outil sous

tension.

20. Avant d’utiliser l’outil sur la pièce, laissez-le

tourner à vide un instant. Soyez attentif à toute

vibration ou sautillement pouvant indiquer que

la lame n’est pas bien installée ou est mal

équilibrée.

21. Attendez que la lame atteigne sa pleine vitesse

avant de procéder à la coupe.

22. Cessez immédiatement l’utilisation si vous notez

une quelconque anomalie.

23. N’essayez pas de verrouiller la gâchette en

position de marche.

24. Demeurez attentif en tout temps, et tout

particulièrement lors des travaux répétitifs et

monotones. Ne vous laissez pas emporter par

un sentiment de sécurité trompeur. Les lames ne

pardonnent pas.

25. N’utilisez que les accessoires recommandés

dans le présent manuel d’instructions.

L’utilisation d’accessoires inappropriés, tels que

des disques abrasifs, peut entraîner une

blessure.

26. Ne tenez JAMAIS la pièce du côté droit de la scie

avec la main gauche, et vice versa. Cela

La page charge ...

Makita LS1040 Le manuel du propriétaire

Marque: Makita

Modèle: LS1040

Catégorie: Scies à onglet

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Makita LS1040 Owner's manual
español: Makita LS1040 El manual del propietario

Makita LS1040 Le manuel du propriétaire

Makita LS1040 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents