VTech DS6671-4 Manuel utilisateur

User’s manual

w w w.v t e c h p h o n e s. c o m

Models:

DS6671-2/DS6671-3/

DS6671-4/DS6672-4/

DS667V-2F/DS667V-2G/

DS667V-2H/DS667V-2J BC

Congratulations

on purchasing your new VTech product. Before using this telephone, please read

Important safety instructions on page 94 of this manual.

This manual has all the feature operations and troubleshooting necessary to install

and operate your new VTech telephone. Please review this manual thoroughly to

ensure proper installation and operation of this innovative and feature rich VTech

product. For support, shopping, and everything new at VTech, visit our website at

www.vtechphones.com. In Canada, please visit www.vtechcanada.com.

Telephones identiﬁed with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc.

and any use of such marks by VTech Holdings Limited is under license.

VTech Holdings Limited is a member of Bluetooth SIG, Inc.

Other trademarks and trade names are those of their respective owners.

Register online to get an additional 3-month warranty!

Visit www.vtechphones.com.

Registration

Register your product online for enhanced warranty support.

Product news

Learn about the latest VTech products.

T

Compatible with

Hearing Aid T-Coil

TIA-1083

i

Table of contents

Getting started ......................... 1

Parts checklist ....................................1

Telephone base and charger

installation .......................................2

Handset battery installation ................3

Handset battery charging ...................4

Headset charging ...............................5

Headset battery ..................................6

Earbud installation ..............................7

Ear hook installation ...........................8

Head band installation ......................11

Are you a new cable or VoIP

subscriber? ...................................13

Did you subscribe to voicemail

service from your telephone

service provider? ...........................14

Handset layout ..................................15

Telephone base layout ......................18

Headset layout ..................................20

Bluetooth ................................21

Introducing Bluetooth ........................21

Glossary of terms ............................23

Bluetooth setup .................................24

VTech Connect to Cell™ application ...24

Add a cell phone ...............................25

Auto connection ................................26

Connect a paired cell phone .............26

Disconnect a paired cell phone ........26

Cell ringer (Ringtone Share) .............26

Download phonebook .......................27

Telephone settings ................ 28

Using the menu ................................28

Handset ringer volume .....................29

Telephone base ringer volume .........29

Headset ringer volume .....................29

Ringer tone .......................................30

Quiet mode .......................................30

Set date and time .............................31

LCD language ...................................32

Voicemail number .............................33

Clear voicemail indicators .................34

Key tone ............................................34

CID time synchronization ..................35

Dial mode .........................................35

Telephone operation .............36

Make a home call .............................36

Predial a home call ...........................36

Answer a home call ..........................36

End a home call ................................36

Call waiting on the home line ............36

Make a cell call .................................37

Answer a cell call ..............................37

End a cell call ...................................37

Call waiting on the cell line ...............38

Answer a cell call while on

a home call ....................................38

Cell phone voicemail ........................38

Answer a home call while on

a cell call .......................................38

Handset speakerphone ....................38

Volume control ..................................39

Mute ..................................................39

Hold ..................................................39

Redial ...............................................40

Website .............................................40

Temporary ringer silencing ...............41

Chain dialing .....................................41

Temporary tone dialing .....................42

Find handset .....................................42

Check voicemail................................42

Multiple handset use ............. 43

Join a call in progress .......................43

Intercom ............................................44

Answer an incoming call during

an intercom call .............................45

Transfer a call using intercom ...........46

Push-to-talk (PTT) ............................47

PTT to a single handset ....................48

PTT to multiple handsets ..................49

Answer a PTT call.............................50

Change a one-to-one PTT call to

an intercom call .............................50

End a PTT call ..................................51

Answer an incoming call during

a PTT call ......................................51

ii

Table of contents

Make an outgoing call during

a PTT call ......................................51

Phonebook ............................. 52

About the phonebook .......................52

Add a phonebook entry to the

home phonebook ..........................53

Review phonebook entries ...............55

Alphabetical search ..........................55

Dial a phonebook entry ....................56

Edit a phonebook entry ....................56

Delete a phonebook entry ................57

Remove an entire cell phonebook ....57

Caller ID ..................................58

About caller ID ..................................58

Information about caller ID with

call waiting .....................................58

Caller ID log ......................................59

Memory match ..................................59

Missed call indicator .........................60

Review the caller ID log ....................60

View dialing options ..........................61

Dial a caller ID log entry ...................62

Save a caller ID log entry to the

home phonebook ..........................62

Delete caller ID log entries ...............63

Caller ID log screen messages .........63

Answering system settings ...64

Answering system ............................64

Announcement .................................64

Record your own announcement ......64

Play your announcement ..................64

Delete your announcement ..............65

Answer on/off ....................................65

Call screening ...................................66

Number of rings ................................66

Remote access code ........................67

Message alert tone ...........................67

Recording time .................................68

Answering system

operation .............................69

Answering system and voicemail ......69

Using the answering system

and voicemail together ..................69

Message capacity .............................70

New message indication ...................70

Call screening ...................................70

Call intercept .....................................71

Temporarily turn off the message

alert tone .......................................71

Message playback ............................72

Delete all old messages ...................73

Record, play and delete memos .......73

Remote access .................................74

Appendix ................................75

Expand your telephone system ........75

Message window displays ................76

Screen messages .............................77

Handset and telephone base

indicators .......................................79

Headset indicators ............................81

Troubleshooting ................................82

Important safety instructions ............92

Battery ..............................................93

Precautions for users of implanted

cardiac pacemakers ......................93

Operating range ................................93

ECO mode ........................................93

Maintenance .....................................94

About cordless telephones ...............94

The RBRC® seal ...............................95

FCC, ACTA and IC regulations .........96

California Energy Commission

battery charging testing

instructions ....................................98

For C-UL compliance only ................99

Limited warranty .............................101

Technical speciﬁcations ..................103

Index .....................................104

1

The headset battery is not replaceable.

To purchase replacement batteries or power adapters, visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or dial 1 (800) 267-7377.

•

Parts checklist

Your telephone package contains the following items. Save your sales receipt and

original packaging in case it is necessary to ship your telephone for warranty service.

Getting started

Abridged user’s manualTelephone base

Handset battery

(1 for DS6671-2/DS667V-2F/

DS667V-2G/ DS667V-2H/

DS667V-2J)

(2 for DS6671-3)

(3 for DS6671-4/DS6672-4)

Handset battery

compartment cover

(1 for DS6671-2/DS667V-2F/

DS667V-2G/ DS667V-2H/

DS667V-2J)

(2 for DS6671-3)

(3 for DS6671-4/DS6672-4)

Telephone

line cord

Telephone base

power adapter

Cordless

headset with an

earbud attached

Ear hooks (3) Additional

earbuds (3)

Head band

Handset charger and

charger adapter

(1 for DS6671-3)

(2 for DS6671-4/DS6672-4)

Handset

(1 for DS6671-2/DS667V-2F/

DS667V-2G/ DS667V-2H/

DS667V-2J)

(2 for DS6671-3)

(3 for DS6671-4/ DS6672-4)

Ear pad

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Quick start guide

Quick start

guide

Abridged

user’s manual

Getting started

2

Telephone base and charger installation

Install the telephone base and handset charger(s) as shown below.

Make sure that the electrical outlet is not controlled by a wall switch.

If you subscribe to digital subscriber line (DSL) high-speed Internet service through

your telephone line, you must install a DSL filter between the telephone line cord

and the telephone wall jack. The filter prevents noise and caller ID problems caused

by DSL interference. Contact your DSL service provider for more information about

DSL filters.

Telephone base Handset charger

If you have DSL

high-speed Internet

service, a DSL ﬁlter

(not included) is

required.

The DSL ﬁlter must

be plugged into the

telephone wall jack.

Electrical outlet not

controlled by a wall

switch

Charger

adapter

Telephone

wall jack

Telephone base

power adapter

Telephone

line cord

Use only the power adapters supplied with this product. To order a replacement,

visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada,

go to www.vtechcanada.com or call 1 (800) 267-7377.

The power adapters are intended to be correctly oriented in a vertical or floor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

Even if you do not subscribe to any conventional telephone service, you can still

use the cell line alone without plugging in a telephone line cord.

CAUTION:

If you subscribe to telephone service from a cable company or a VoIP service provider, contact

your cable/VoIP service provider for more information.

•

3

Handset battery installation

Install the battery as shown below.

Plug the battery connector securely

into the socket inside the handset

battery compartment, matching the

orientation of the engraved label.

1.

If the handset will not be used for a long time, disconnect and remove the battery

to prevent possible leakage.

To purchase replacement batteries, visit our website at www.vtechphones.com

or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or dial

1 (800) 267-7377.

•

Getting started

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

IMPORTANT:

Check for a dial tone by pressing

/HOME

, CELL 1 or CELL 2. If you hear a dial tone, the

installation is successful.

If you do not hear a dial tone:

Make sure the installation procedures described above are properly done.

It may be a wiring problem. If you have changed your telephone service to digital service

from a cable company or a VoIP service provider, the telephone line may need to be

rewired to allow all existing telephone jacks to work. Contact your cable/VoIP service

provider for more information.

•

Place the battery with the label

THIS SIDE UP facing up and the wires

inside the battery compartment.

2.

Align the cover flat against the battery

compartment, then slide it towards the

center of the handset until it clicks into

place.

3. Charge the handset by placing it in the

telephone base or handset charger.

The CHARGE light is on when the

handset is charging.

4.

CHARGE light

remains on

when charging.

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Getting started

4

Handset battery charging

Once you have installed the battery, the handset LCD display indicates the battery

status (see the table below).

NOTES

For best performance, keep the handset in the telephone base or charger when not in use.

The battery is fully charged after 12 hours of continuous charging.

If you place the handset in the telephone base or the charger without plugging in the

battery, the screen displays No battery.

Battery indicators Battery status Action

The screen is blank, or

displays Place in charger

and flashes.

The battery has no or very

little charge. The handset

cannot be used.

Charge without interruption

(about 30 minutes).

The screen displays

Low battery and flashes.

The battery has enough

charge to be used for a

short time.

Charge without interruption

(about 30 minutes).

The screen displays

HANDSET X.

The battery is charged. To keep the battery charged,

place it in the telephone

base or handset charger

when not in use.

•

After you install your telephone or power returns following a power

outage, the handset will prompt you to set the date and time.

For instructions, see Set date and time on page 31.

To skip setting, press CANCEL.

SET DATE

MM/DD/YY

When it is fully charged, you can expect the following performance:

Operation Operating time

While in handset use (talking*) Seven hours

While in speakerphone mode (talking*) Three hours

While not in use (standby**) Five days

* Operating times vary depending on your actual use and the age of the battery.

** Handset is not charging or in use.

Getting started

5

Headset charging

After installing the telephone base, charge the headset as shown below. The

headset is fully charged after three hours of continuous charging. If the light does

not turn on while charging, you need to charge the headset without interruption for

at least 15 minutes to give the headset enough charge to use for a short time. For

best performance, keep the headset in the telephone base when not in use.

Place the tip of the headset in the small cradle on the telephone base.1.

The magnet holds the top of the headset in place. The light turns on

when charging.

2.

The light

Getting started

6

Headset battery

It takes up to three hours for the battery to be fully charged. When it is fully

charged, you can expect the following performance:

Operation Operating time

While in use (talking*) Nine hours

While not in use (standby**) Ninety hours

* Operating times vary depending on your actual use and the age of the battery.

** Headset is not charging or in use.

The battery needs charging when:

The headset beeps twice every 20 seconds.

The light is off when in idle mode.

The light flashes every 10 seconds in red.

Conserve battery life:

To reduce the risk of fire or injury, read and follow these instructions:

The headset battery is not replaceable.

If the headset will not be used for a long period of time, press and hold on the headset

to power off the headset and conserve the headset battery life. The light flashes three

times in red when the headset is being powered off.

CAUTION:

To prevent fire or shock hazard, do not expose this product to water or any type of moisture.

•

Getting started

7

Earbud installation

There are four earbuds provided and one of them has already been attached to

the headset.

To remove the earbud from the headset earpiece:

Hold both sides of the earbud and then pull the earbud until it separates from

the earpiece.

To attach the earbud to the headset earpiece:

Choose an appropriate earbud.

Press the earbud towards the earpiece until it clicks into place. Move the earbud

around so that the protruding bump on the earbud is pointing towards your mouth

when placed on your ear. The protruding bump on the earbud holds the headset

securely in your ear.

1.

2.

Protruding bump

Getting started

8

Ear hook installation

There are three ear hooks provided. The smallest ear hook is a flexible ear hook. If

you choose to use it, adjust to suit your ear comfortably before use.

To attach the ear hook to the headset:

Remove any headset attachment (earbud excluded) connected to the headset.

Choose an appropriate ear hook.

Insert the ear hook [A] into the rotating clip [B] on the headset until it clicks

into place.

1.

2.

3.

Hook the headset on your right ear. Adjust the angle of the headset until the

microphone is pointing towards your mouth. Firmly grip the earpiece with one

hand whenever adjusting the headset microphone up or down.

4.

[B]

[A]

Getting started

9

Hold the headset with one

hand. Lift the ear hook upward.

1. Twist the ear hook 180 degrees

clockwise.

2.

Push the ear hook downward.3. Hook the headset on your left ear.

Adjust the angle of the headset until

the microphone is pointing towards

your mouth.

4.

Ear hook installation

To adjust the headset to wear on your left ear:

Getting started

10

Ear hook installation

To remove the ear hook from the headset:

Hold the headset with one hand and the ear hook with your other hand.

Pull the end of the ear hook up until it separates from the rotating clip on

the headset.

1.

2.

Getting started

11

Head band installation

To attach the head band to the headset:

Remove any headset attachment connected to the headset.

Attach the ear pad to the headset earpiece.

1.

2.

To wear the headset on your right ear, insert the end [A] of the head

band into the rotating clip [B] on the headset until it clicks into place.

3.

[B]

[A]

Getting started

12

Head band installation

Adjust the head band to fit your head. Adjust and rotate the angle of the headset

until the microphone is pointing towards your mouth. Firmly grip the earpiece with

one hand whenever adjusting the headset microphone up or down.

4.

To remove the head band from the headset:

Hold the headset with one hand and the head band with your other hand.

Pull the end of the head band until it separates from the rotating clip on

the headset.

1.

2.

To wear on your left ear, hold the headset on one hand and the head band with your other

hand. Rotate the head band within the rotating clip on the headset.

Getting started

13

Are you a new cable or VoIP subscriber?

If your answer is yes, the existing telephone jacks in your home may no longer

work. Your cable/VoIP service provider uses a different connection, separate from

your old traditional telephone service, to connect the modem/router/terminal adapter

installed in your home.

To allow all existing telephone jacks to work, contact your telephone service

provider for solutions, such as rewiring services (fees may apply).

If your answer is no, your existing telephone jacks will continue to work as normal.

OLD

Conventional

telephone line jack

Main

landline

NEW

Modem/Router/

Terminal adapter

Cable or

Internet

Getting started

14

Did you subscribe to voicemail service from your telephone service

provider?

Your telephone has a built-in answering system and supports voicemail feature

offered by your telephone service provider (subscription is required, and fees may

apply). Refer to Answering system and voicemail on page 69 for more details.

To use the built-in answering system:

You may see this online Complete user’s manual on how to record your outgoing

announcement, retrieve messages and other related operations. You may also see

the Abridged user’s manual provided in the product package for abbreviated

instructions.

To use the voicemail:

To retrieve your voicemail messages, you typically dial an access number provided

by your telephone service provider, and then enter a security code. Contact your

telephone service provider for instructions on how to configure the voicemail

settings and listen to messages.

Getting started

15

Handset layout

CHARGE light

On when the handset is charging in the telephone base

or handset charger (page 3).

VOLUME/ / (phonebook)

Press to review the phonebook when the phone is not in

use (page 55).

Press to scroll up while in a menu, or in the phonebook,

caller ID log or redial list.

While entering names or numbers, press to move the

cursor to the right.

During a call or message playback, press to increase the

listening volume (page 39 or 72).

VOLUME/ /CID (caller ID)

Press to review the caller ID log when the phone is not in

use (page 60).

Press to scroll down while in a menu, or in the

phonebook, caller ID log or redial list.

While entering names or numbers, press to move the

cursor to the left.

During a call or message playback, press to decrease

the listening volume (page 39 or 72).

OFF/CANCEL

During a call, press to hang up (pages 36 and 37).

While in a menu, press to return to the previous menu,

or press and hold to return to idle mode, without

making changes.

While the phone is ringing, press to silence the handset

ringer temporarily (page 41).

Press and hold to erase the missed call indicator when

the phone is not in use (page 60).

Press repeatedly to display other dialing options while

reviewing a caller ID log entry (page 61).

Press and hold to set and turn on the quiet mode, or to

turn it off when the handset is not in use (page 30).

While the phone is ringing, press to silence the handset

ringer temporarily (page 41).

While saving a caller ID log entry to the home

phonebook, press to toggle name order (page 62).

HOLD

Press to put current call on hold.

/HOME/FLASH

Press to make or answer a home call (page 36).

During a call, press to answer an incoming home call

when you receive a call waiting alert (page 36).

•

Getting started

16

Handset layout

REDIAL/PAUSE

Press repeatedly to view the last 10 numbers dialed

(page 40).

While entering numbers, press and hold to insert a

dialing pause (pages 33, 53, 54 and 62).

MENU/SELECT

Press to show the menu (page 28).

While in the menu, press to select an item or save an

entry or setting.

CELL 1/ CELL 2

Press to make or answer a cell call (page 37).

During a cell call, press to answer an incoming cell call

when you hear a call waiting alert (page 38).

1

While reviewing a caller ID log entry, press repeatedly to

add or remove 1 in front of the telephone number before

dialing or saving it in the phonebook (page 61).

Press and hold to set or dial your voicemail number when

the phone is not in use (page 33).

Dialing keys

Press to enter numbers or characters.

Press to answer an incoming call (pages 36 and 37).

/auA

During a call, press to switch to tone dialing if you have

pulse service (page 42).

While entering characters, press to switch between

upper case and lower case.

MUTE/DELETE

During a call, press to mute the microphone

(page 39).

While the phone is ringing, press to silence the handset

ringer temporarily (page 41).

While reviewing the redial list, phonebook or caller ID log,

press to delete an individual entry

(page 40, page 57 and page 63 respectively).

While using the dialing keys, press to delete digits, or

press and hold to delete all digits.

(Speakerphone)

Press to make or answer a call using the handset

speakerphone (page 36).

During a call or message playback, press to switch

between the handset speakerphone and the cordless

handset (page 38 or 72).

•

La page charge ...

VTech DS6671-4 Manuel utilisateur

Ce manuel convient également à

VTech DS6671-4 Manuel utilisateur

dans d''autres langues

Documents connexes