Spectrum Controls 2080sc-OW2IHC Le manuel du propriétaire

Spectrum Controls
Marque
Spectrum Controls
Modèle
2080sc-OW2IHC
Taper
Le manuel du propriétaire
User’s Manual Pub. 0300270-02 Rev. A
Micro800TM 2-Channel High-Current
Digital Output Module
Catalog Number: 2080sc-OW2IHC
ii 2080sc-OW2IHC 2-Channel High-Current Digital Output Module
User’s Manual Pub. 0300270-02 Rev. A
Important Notes
1. Please read all the information in this owner’s guide before installing the
product.
2. The information in this owner's guide applies to hardware Series A and
firmware version 1.1 or later.
3. This guide assumes that the reader has a full working knowledge of the
relevant processor.
Notice
The products and services described in this owner's guide are useful in a wide
variety of applications. Therefore, the user and others responsible for applying
the products and services described herein are responsible for determining their
acceptability for each application. While efforts have been made to provide
accurate information within this owner's guide, Spectrum Controls, Inc. assumes
no responsibility for the accuracy, completeness, or usefulness of the information
herein.
Under no circumstances will Spectrum Controls, Inc. be responsible or liable for
any damages or losses, including indirect or consequential damages or losses,
arising out of either the use of any information within this owner's guide or the
use of any product or service referenced herein.
No patent liability is assumed by Spectrum Controls, Inc. with respect to the use
of any of the information, products, circuits, programming, or services referenced
herein.
The information in this owner's guide is subject to change without notice.
Limited Warranty
Spectrum Controls, Inc. warrants that its products are free from defects in
material and workmanship under normal use and service, as described in
Spectrum Controls, Inc. literature covering this product, for a period of 1 year.
The obligations of Spectrum Controls, Inc. under this warranty are limited to
replacing or repairing, at its option, at its factory or facility, any product which
shall, in the applicable period after shipment, be returned to the Spectrum
Controls, Inc. facility, transportation charges prepaid, and which after
examination is determined, to the satisfaction of Spectrum Controls, Inc., to be
thus defective.
This warranty shall not apply to any such equipment which shall have been
repaired or altered except by Spectrum Controls or which shall have been subject
to misuse, neglect, or accident. In no case shall the liability of Spectrum
Controls, Inc. exceed the purchase price. The aforementioned provisions do not
extend the original warranty period of any product which has either been repaired
or replaced by Spectrum Controls, Inc.
Table of Contents
IMPORTANT NOTES ................................................................................................................................................. II
NOTICE ..................................................................................................................................................................... II
LIMITED WARRANTY ................................................................................................................................................ II
TABLE OF CONTENTS ............................................................................................................................................... III
PREFACE .................................................................................................................................................................. IV
MODULE OVERVIEW........................................................................................................................... 1-1
SECTION 1.1 GENERAL DESCRIPTION .......................................................................................................................... 1-1
SECTION 1.2 ENVIRONMENT AND ENCLOSURE .............................................................................................................. 1-2
SECTION 1.1 PREVENT ELECTROSTATIC DISCHARGE ....................................................................................................... 1-4
SECTION 1.2 PARTS LIST .......................................................................................................................................... 1-4
SECTION 1.3 HARDWARE FEATURES ........................................................................................................................... 1-5
SECTION 1.4 MODULE POWER SPECIFICATIONS ............................................................................................................ 1-6
SECTION 1.5 MODULE CHASSIS EARTH GROUND.......................................................................................................... 1-6
INSTALLATION AND WIRING .............................................................................................................. 2-1
SECTION 2.1 INSERT MODULE INTO CONTROLLER ......................................................................................................... 2-1
SECTION 2.2 CONFIGURING THE MODULE .................................................................................................................... 2-3
SECTION 2.3 MODULE OUTPUT DATA ......................................................................................................................... 2-3
SECTION 2.4 ADDING THE OW2IHC TO CCW .............................................................................................................. 2-3
SECTION 2.5 TECHNICAL ASSISTANCE .......................................................................................................................... 2-5
APPENDIX A CONFIGURATION INFORMATION ..................................................................................................... A-1
iv 2080sc-OW2IHC 2-Channel High-Current Digital Output Module
User’s Manual Pub. 0300270-02 Rev. A
Preface
Read this preface to familiarize yourself with the rest of the manual. This preface
covers the following topics:
• Who should use this manual
• How to use this manual
• Rockwell Automation technical support
• Documentation
• Conventions used in this manual
Who Should
Use This Manual
Use this manual if you are responsible for designing, installing, programming, or
troubleshooting control systems that use Allen-Bradley I/O and/or compatible
controllers, such as CompactLogix and ControlLogix.
How to Use
This Manual
As much as possible, we organized this manual to explain, in a task-by-task
manner, how to install, configure, program, operate, and troubleshoot a control
system using the Micro800™ 2080sc-OW2IHC 2-Channel High-Current Digital
Output Module.
Rockwell
Automation
Technical
Support
For technical support, please contact your local Rockwell Automation
TechConnect Office for all Spectrum products. Contact numbers are as follows:
• USA 1-440-646-6900
• United Kingdom 01-908-635-230
• Australia 1-800-809-929
• Mexico 001-888-365-8677
• Brazil 55-11-3618-8800
• Europe +49-211-41553-630
or send an email to support@spectrumcontrols.com.
2080sc-OW2IHC 2-Channel High-Current Digital Output Module v
User’s Manual Pub. 0300270-02 Rev. A
Documentation
If you would like a .PDF version of a manual, you can download a free electronic
version at www.spectrumcontrols.com.
Conventions
Used in This
Manual
The following conventions are used throughout this manual:
• Bulleted lists (like this one) provide information not procedural steps.
• Numbered lists provide sequential steps or hierarchical information.
• Italic type is used for emphasis.
• Bold type identifies headings and sub-headings:
WARNING
Identifies information about practices or circumstances that can lead to
personal injury or death, property damage, or economic loss. Attentions
help you to identify a hazard, avoid a hazard, and recognize the
consequences.
ATTENTION
Actions ou situations risquant d’entraîner des blessures pouvant être
mortelles, des dégâts matériels ou des pertes financières. Les messages
« Attention » vous aident à identifier un danger, à éviter ce danger et en
discerner les conséquences.
NOTE
Identifies information that is critical for successful application and
understanding of the product.
vi 2080sc-OW2IHC 2-Channel High-Current Digital Output Module
User’s Manual Pub. 0300270-02 Rev. A
User’s Manual Pub. 0300270-02 Rev. A
Module Overview
Section 1.1
General
Description
1.1.1 What is it?
The 2080sc-OW2IHC 2-Channel High-Current Digital Output Module is a relay
output module designed for use with Rockwell Automation Micro800™ systems.
This module provides Form A (N.O.) isolated electromechanical relay outputs
rated at up to 10 A at 30 VDC or 10 A at 250 VAC for control of equipment and
devices. The module interfaces with the controller via an Asynchronous Parallel
Interface (API) which it shares with other plug-in peripherals in the controller.
Power is provided across the same connector used to implement the APIs.
1.1.2 How does it connect mechanically?
The module plugs into any spare plug-in slot on the PLC. A 40-pin connector
provides the connection between the controller and the module. Channel-to-
channel isolation is provided on this relay module.
Output relay connections are connected to the module via a 12-pin terminal block
on the module.
1.1.3 How does it connect via software?
The exchange of data between the module and controller is used to communicate
the commanded output state (ON or OFF) of each relay output of the module.
Other types of exchanges also occur across the API. These exchanges include
reset commands by the controller, interrupts from the module to the controller,
module status queries by the controller, configuration changes and other
associated communications.
The plug-in module contains memory with specific locations holding
configuration, status, and channel values accessible to the Controller as register
locations.
1.1.4 How does it indicate normal function?
Each of the two output channels has a yellow LED indicator. When the module is
commanded to turn an output module ON, the LED for the channel lights. When
the module is commanded to turn a channel OFF, or no command is given to turn
on the channel during startup, the LED remains OFF.
The module operates in normal run mode when installed in a Micro800 controller
chassis and is powered on and is designed to operate 24 hours a day, 7 days a
week for a period of years.
1-2 Chapter 1: Module Overview
User’s Manual Pub. 0300270-02 Rev. A
Section 1.2
Environment
and Enclosure
WARNING
This equipment is intended for use in a Pollution Degree 2 industrial
environment, in overvoltage Category II applications (as defined in IEC
publication 60664-1), at altitudes up to 2000 meters (6562 feet) without
derating.
This equipment is considered Group 1, Class A industrial equipment
according to IEC/CISPR Publication 11. Without appropriate precautions,
there may be potential difficulties ensuring electromagnetic compatibility
in other environments due to conducted as well as radiated disturbance.
This equipment is supplied as open-type equipment. It must be mounted
within an enclosure that is suitably designed for those specific
environmental conditions that will be present and appropriately designed
to prevent personal injury resulting from accessibility to live parts. The
enclosure must have suitable flame-retardant properties to prevent or
minimize the spread of flame, complying with a flame spread rating of 5
VA, V2, V1, V0 (or equivalent) if non-metallic. The interior of the
enclosure must be accessible only by the use of a tool. Subsequent
sections of this publication may contain additional information regarding
specific enclosure type ratings that are required to comply with certain
product safety certifications.
In addition to this publication, see:
• Industrial Automation Wiring and Grounding Guidelines, Allen-
Bradley publication 1770-4.1, for additional installation
requirements.
• NEMA Standards publication 250 and IEC publication 60529, as
applicable, for explanations of the degrees of protection provided
by different types of enclosure.
Chapter 1: Module Overview 1-3
User’s Manual Pub. 0300270-02 Rev. A
ATTENTION
Cet équipement est prévu pour fonctionner en environnement industriel
avec une pollution de niveau 2, dans des applications de surtension de
catégorie II (telles que définies dans la publication 60664-1 de la CEI) et à
une altitude maximum de 2000 m sans déclassement.
Cet équipement est considéré comme étant un équipement industriel du
Groupe 1, classe A selon CEI/CISPR 11. En l’absence de précautions
appropriées, des problèmes de compatibilité électromagnétique peuvent
survenir dans des environnements résidentiels et dans d’autres
environnement en raison de perturbations conduites et rayonnées.
Cet équipement est fourni en tant qu’équipement de type « ouvert ». Il doit
être installé à l’intérieur d’une armoire fournissant une protection adaptée
aux conditions d’utilisation ambiantes et suffisante pour éviter toute
blessure pouvant résulter d’un contact direct avec des composants sous
tension.
L’armoire doit posséder des propriétés ignifuges capables d’empêcher ou
de limiter la propagation des flammes, correspondant à un indice de
propagation de 5VA, V2, V1, V0 (ou équivalent) dans le cas d’une armoire
non métallique.
L’accès à l’intérieur de l’armoire ne doit être possible qu’à l’aide d’un
outil. Cette armoire doit permettre des connexions d’alimentation par un
système de câblage de Classe I, Division 2, conformément au code
électrique national (NEC). Certaines sections de la présente publication
peuvent comporter des recommandations supplémentaires portant sur les
indices de protection spécifiques à respecter pour maintenir la conformité à
certaines normes de sécurité.
En plus de cette publication, consultez:
• La publication Rockwell Automation 1770-4.1, « Industrial
Automation Wiring and Grounding Guidelines », pour d’autres
critères d’installation.
• La publication 250 de la norme NEMA ou la publication 60529 de
la CEI, selon le cas, pour obtenir une description des indices de
protection que fournissent les différents types d’armoires.
1-4 Chapter 1: Module Overview
User’s Manual Pub. 0300270-02 Rev. A
Section 1.3
Prevent
Electrostatic
Discharge
WARNING
Electrostatic discharge can damage integrated circuits or semiconductors if
you touch bus connector pins. Follow these guidelines when you handle
the module:
• Touch a grounded object to discharge static potential.
• Wear an approved wrist-strap grounding device.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the module.
• If available, use a static-safe workstation.
• When not in use, keep the module in its static-shield box.
ATTENTION
Cet équipement est sensible aux décharges électrostatiques, lesquelles
peuvent entraîner des dommages internes et nuire à son bon
onctionnement.
Conformez-vous aux directives suivantes lorsque vous manipulez cet
équipement:
• Touchez un objet mis à la terre pour vous décharger de toute
électricité statique éventuelle.
• Portez au poignet un bracelet antistatique agréé.
• Ne touchez pas les connecteurs ni les broches figurant sur les
cartes des composants.
• Ne touchez pas les circuits internes de l’équipement.
• Utilisez si possible un poste de travail antistatique.
• Lorsque vous n’utilisez pas l’équipement, stockez-le dans un
emballage antistatique.
Section 1.4
Parts List
Your package contains one Micro800 2-Channel High-Current Digital Output
Module, installation screws, and one Quick Start Guide.
You can choose to wire the plug-in before inserting it into the controller or wire
it once the module is secured in place.
Chapter 1: Module Overview 1-5
User’s Manual Pub. 0300270-02 Rev. A
WARNING
• This equipment is considered Group 1, Class A industrial
equipment according to IEC/CISPR 11. Without appropriate
precautions, there may be difficulties with electromagnetic
compatibility in residential and other environments due to
conducted and radiated disturbance.
• Be careful when stripping wires. Wire fragments that fall into the
controller could cause damage. Once wiring is complete, make
sure the controller is free of all metal fragments before removing
the protective debris strip.
• Do not wire more than 2 conductors on any single terminal.
• If you insert or remove the plug-in module while power is on, an
electrical arc can occur. This could cause an explosion in
hazardous location installations. Be sure that power is removed or
the area is nonhazardous before proceeding.
• Do not insert or remove the plug-in module while power is
applied; otherwise, permanent damage to equipment may occur.
ATTENTION
• Cet équipement est considéré comme étant un équipement
industriel du Groupe 1, classe A selon CEI/CISPR 11. En
l’absence de precautions appropriées, des problèmes de
compatibilité électromagnétique peuvent survenir dans des
environnements résidentiels et dans d’autres environnements en
raison de perturbations conduites et rayonnées.
• Soyez vigilant en dénudant les fils. Tout fragment de fil tombé
dans l’automate risquerait de le détériorer. Une fois le câblage
terminé, veillez à ce que l’automate ne présente aucun copeau de
métal avant de retirer la bande de protection.
• Ne câblez pas plus de 2 conducteurs sur une même borne.
• L’insertion ou le retrait du module enfichable sous tension peut
provoquer un arc électrique, susceptible de provoquer une
explosion dans un environnement dangereux. Assurez-vous que
l’alimentation est coupée ou que l’environnement est classé non
dangereux avant de poursuivre.
• N’insérez pas et ne retirez pas le module enfichable quand
l’équipement est sous tension, au risque de provoquer des
dommages irrémédiables à l’équipement.
Section 1.5
Hardware Features
The module plugs into, and communicates with, a controller in the Micro800
family. The only exchange of data between the controller and the Plug-In Module
is through the API. The Plug-In Module shares the parallel bus with other plug-in
peripherals in the controller.
1-6 Chapter 1: Module Overview
User’s Manual Pub. 0300270-02 Rev. A
The block diagram for the Plug-In Module interface is shown below:
Section 1.6
Module Power
Specifications
The controller provides two Power Supplies to the module:
• 3.3 Volts (3.0 V Min, 3.6 V Max), Current Rating: 60 mA.
• 24 Volts (20.4 V Min, 26.4 V Max), Current Rating: 60 mA.
You may not use an external power source to power the module. Refer to the
specifications in the Appendix for further information.
Section 1.7
Module Chassis
Earth
Ground
The Micro800 controller does not have a chassis (earth) ground. If a chassis
(earth) ground connection is needed for a Plug-In Module or devices connected
to a Plug-In Module, it must be provided externally. A capacitive coupling
between chassis (earth) ground and Plug-In module signal ground is acceptable if
required. The capacitor must be rated for least 500 VAC (707 VDC). The
module does not use a chassis ground since it is not available on the backplane or
the terminal block.
User’s Manual Pub. 0300270-02 Rev. A
Installation and Wiring
Section 2.1
Insert Module
into Controller
Follow the instructions to insert and secure the plug-in module to the controller.
WARNING
Electrostatic discharge can damage integrated circuits or semiconductors if
you touch bus connector pins. Follow these guidelines when you handle
the module:
• Touch a grounded object to discharge static potential.
• Wear an approved wrist-strap grounding device.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the module.
• If available, use a static-safe workstation.
• When not in use, keep the module in its static-shield box.
ATTENTION
Cet équipement est sensible aux décharges électrostatiques, lesquelles
peuvent entraîner des dommages internes et nuire à son bon
onctionnement.
Conformez-vous aux directives suivantes lorsque vous manipulez cet
équipement:
• Touchez un objet mis à la terre pour vous décharger de toute
électricité statique éventuelle.
• Portez au poignet un bracelet antistatique agréé.
• Ne touchez pas les connecteurs ni les broches figurant sur les
cartes des composants.
• Ne touchez pas les circuits internes de l’équipement.
• Utilisez si possible un poste de travail antistatique.
• Lorsque vous n’utilisez pas l’équipement, stockez-le dans un
emballage antistatique.
WARNING
To comply with the CE Low Voltage Directive (LVD), all connected I/O
must be powered from a source compliant with the following: Safety Extra
Low Voltage (SELV) or Protected Extra Low Voltage (PELV).
2-2 Chapter 2: Installation and Wiring
User’s Manual Pub. 0300270-02 Rev. A
1. Position the plug-in module with the terminal block facing the front of
the controller as shown:
2. Snap the module into the module bay.
3. Using a screwdriver, tighten the supplied, self-tapping screw to torque
specifications.
4. Follow the wiring diagram below to wire the module:
NOTE
In the diagram above, terminals with the same label are internally shorted
together. Example, CM0 (Top Row) and CM0 (Bottom Row) are
internally shorted together.
Chapter 2: Installation and Wiring 2-3
User’s Manual Pub. 0300270-02 Rev. A
Section 2.2
Configuring
the Module
The 2080sc-OW2IHC configuration consists only of placing it into run mode or
stopping it.
To place the module in run, write a value of A5 Hex (165 decimal) to offset 17
(the MOD_MODE_CONTROL parameter).
NOTE
Micro 800 controllers running OS firmware revision 1.12 or older, require
a decimal value of 16 be written to offset 11 (the CONTR_OPS_STATUS
parameter) before the module will go into run mode. See the program
sample later in the manual.
Table 2-1. General Module Status
Bit Number Description
0-1
These 2 bits define module operation mode:
• 0: Idle: Module is ready to RUN, and I/O is off.
• 1: RUN: Module is under RUN, and I/O is on.
• 2: Error: Error happens, and I/O is off.
• 3: Busy: Module is busy, cannot go to RUN, and I/O is
off.
Section 2.3
Module Output Data
The two output channels on the OW2IHC are controlled by memory location 64;
bits 0 and 1 control channels 0 and 1 respectively. See Table 2-3 for memory
location offsets. The table below describes the state of each output channel in
relation to the control bits.
Table 2-2. Module Output Data
Channel Number
Bit State
Output State
0 0 OPEN
1 CLOSED
1
0
OPEN
1 CLOSED
Section 2.4
Adding the OW2IHC to CCW
The 2080sc-OW2IHC is configured for CCW (Connected Components
Workbench) using the PLUGIN_READ and PLUGIN_WRITE instructions for
generic plug-in modules.
The configuration, output data, and status structures discussed in the sections
above, are stored at different memory locations in the module. The following
table lists the memory location offset for each parameter which is used when
2-4 Chapter 2: Installation and Wiring
User’s Manual Pub. 0300270-02 Rev. A
configuring the PLUGIN_READ, WRITE, and INFO instructions.
Table 2-3. Parameter Offset
Parameter
Offset (Dec)
Comments
MOD_ID_LO 0 Module ID
MOD_ID_HI 1
VENDOR_ID_LO 2 Vendor ID
VENDOR_ID_HI 3
PRODUCT_TYPE_LO
4
PRODUCT_TYPE_HI 5
PRODUCT_CODE_LO
6
PRODUCT_CODE_HI 7
MOD_REV_LO
8
Minor revision, 1-255
MOD_REV_HI
9
Major revision, 1-127
CONTR_OPS_STATUS
11
Controller operation status
information
(see Table 2-4)
MOD_STATUS
16
Module status register
(see Table 2-1)
MOD_MODE_CONTROL
17
Module Mode Control Register
OUTPUT_DATA 64 Output Data Register
Table 2-4. Controller Operation Status Register
Bit Number Description
0-3 Controller Error info:
0×00: no Error.
0×01: Operation Error.
0×02: Fatal Error.
0×03-0x0F: reserved.
c4-5
0×00: non-RUN mode.
0×01: RUN mode.
0×02-0×03 : reserved.
6-7 Controller Power info:
0×00: Power O.K.
0×01: power failure
triggered.
0×02-0×03: reserved.
Chapter 2: Installation and Wiring 2-5
User’s Manual Pub. 0300270-02 Rev. A
The following sample program, written in structured text, demonstrates how to
configure the module in CCW:
u800Slot := 1; (* Slot number for module. *)
(* This section of code is to handle the controller with
Firmware earlier than rev 1.13 *)
SYS_INFO_FW(True);
IF (SYS_INFO_FW.Sts.OSMajRev = 1 and
SYS_INFO_FW.Sts.OSMinRev <=12) THEN
IF SYS_INFO_FW.Sts.MajErrCode = 0 THEN
ControllerStatus[1] := 2#00010000;
WriteControllerStatus(True,u800Slot,11,1,ControllerStatus);
END_IF;
END_IF;
RunMode[1] := 16#A5; (* Initialize RunMode register *)
WriteModModeControl(true,u800Slot,17,1,RunMode); (*
Write A5 Hex to MOD_MODE_CONTROL for run mode*)
ReadModStatus(true,u800Slot,16,1,OW2IHC_S1_ModStatus);
(* Read general module status *)
WriteOutputs(True,u800Slot,64,1,OW2IHC_S1_Outputs); (*
Write Output states *)
Table 2-5. CCW Program Variables
Variable Name
Data Type
Dimension
U800Slot UINT NA
SYS_INFO_FW
SYS_INFO
NA
ControllerStatus USINT [1..1]
WriteControllerStatus
Plugin_Write
NA
WriteModModeControl Plugin_Write NA
RunMode USINT [1..1]
ReadModStatus Plugin_Read NA
OW2IHC_S1_ModStatus USINT [1..1]
WriteOutputs Plugin_Write NA
OW2IHC_S1_Outputs USINT [1..1]
The sample project above can be downloaded from our website at
www.spectrumcontrols.com.
Section 2.5
Technical Assistance
Note that your module contains electrostatic components that are susceptible to
damage from electrostatic discharge (ESD). An electrostatic charge can
accumulate on the surface of ordinary wrapping or cushioning material. In the
2-6 Chapter 2: Installation and Wiring
User’s Manual Pub. 0300270-02 Rev. A
unlikely event that the module should need to be returned to Spectrum
Controls, Inc., please ensure that the unit is enclosed in approved ESD
packaging (such as static-shielding/metallized bag or black conductive
container). Spectrum Controls, Inc. reserves the right to void the warranty on
any unit that is improperly packaged for shipment.
For further information or assistance, please contact your local distributor, or call
the technical support number provided under the Technical Support section in the
Preface.
User’s Manual Pub. 0300270-02 Rev. A
Appendix A
Configuration Information
This appendix contains configuration information as follows:
Output Specifications
Description 2-Channel Relay Output Module
Relay
Functionality
Form A normally open
Output
Current
Rating
(at rated
power)
Resistive load at up to 30° C
10 A at 5-30 VDC
10 A at 125 VAC
10 A at 125 VAC
Resistive load at up to 65° C
6 A at 5-30 VDC
6 A at 125 VAC
6 A at 125 VAC
Output Power
Rating
(Resistive
Resistive load at up to 30° C
300 W Maximum for 30.0 VDC
1250 VA Maximum for 125 VAC
2500 VA Maximum for 250 VAC
Inductive Loads
1
1 Connecting surge suppressors across your external load will extend the life of the relay contacts.
A-2 Appendix A: Configuration Information
User’s Manual Pub. 0300270-02 Rev. A
Description 2-Channel Relay Output Module
UL Pilot
Duty Contact
Ratings
(Power factor
0.35 or less
for AC):
Additional UL
ratings:
AC Contact
Rating Code
Designation
Thermal
continuous
test current
(A)
Max. current (A) a, b
Max. VA 120 VAC 240 VAC
Make
Break Make Break Make Break
B300 5 30 3 15 1.5 3600
360
NOTES:
a Power factor 0.35 or less
b For maximum ratings at voltages between the maximum design value
and 120 volts, the maximum make and break ratings are to be obtained
by dividing the volt-amperes rating by the application voltage. For
voltages below 120 volts, the maximum make current is to be the same
as for 120 volts, and the maximum break current is to be obtained by
dividing the break volt-amperes by the application voltage, but these
currents are not to exceed the thermal continuous test current.
DC
Contact
Rating
Code
Designatio
n
Thermal
continuou
s test
current
(A)
Max. make/break current
(A) c, d
Max.
make/
break VA
125 VDC 250 VDC
R150 1.0 0.22 - 28
R300 1.0 0.22 0.11 28
NOTES:
c The maximum make and break ratings are to be obtained by dividing
the volt-
ampere rating by the application voltage, but the current values
are not to exceed the thermal continuous test current.
d
Inductive loads as specified in Section 8.2.7 of Industrial Control and
Systems; Control Circuit and Pilot Devices, ANSI/NEMA
ICS5-1993.
1/3 HP, 125 VAC, 250 VAC
30 VDC Make/Break 2 A (Pilot Duty)
250 VAC, Make 20 A / Break 2 A (Pilot Duty)
2 A, 250 VAC, Tungsten Lamp
2 A, 30 VDC, Tungsten Lamp
Minimum
Load
10 mA at 5 VDC per point.
(This value can change due to the switching frequency, environmental
conditions, and desired reliability level. Therefore, it is recommended
to check this with the actual load.)
Initial Contact
Res. of Relay
< 5 mΩ typical, 30 mΩ max
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Spectrum Controls 2080sc-OW2IHC Le manuel du propriétaire

Spectrum Controls
Marque
Spectrum Controls
Modèle
2080sc-OW2IHC
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents