Fujitsu M8000 Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Manual Code C120-E331-03EN
Part No. 819-7892-10
April 2007, Revision A
SPARC
®
Enterprise
M4000/M5000/M8000/M9000
Servers Administration Guide
Please
Recycle
Copyright 2007 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved.
FUJITSU LIMITED provided technical input and review on portions of this material.
Sun Microsystems, Inc. and Fujitsu Limited each own or control intellectual property rights relating to products and technology described in
this document, and such products, technology and this document are protected by copyright laws, patents and other intellectual property laws
and international treaties. The intellectual property rights of Sun Microsystems, Inc. and Fujitsu Limited in such products, technology and this
document include, without limitation, one or more of the United States patents listed at http://www.sun.com/patents and one or more
additional patents or patent applications in the United States or other countries.
This document and the product and technology to which it pertains are distributed under licenses restricting their use, copying, distribution,
and decompilation. No part of such product or technology, or of this document, may be reproduced in any form by any means without prior
written authorization of Fujitsu Limited and Sun Microsystems, Inc., and their applicable licensors, if any. The furnishing of this document to
you does not give you any rights or licenses, express or implied, with respect to the product or technology to which it pertains, and this
document does not contain or represent any commitment of any kind on the part of Fujitsu Limited or Sun Microsystems, Inc., or any affiliate of
either of them.
This document and the product and technology described in this document may incorporate third-party intellectual property copyrighted by
and/or licensed from suppliers to Fujitsu Limited and/or Sun Microsystems, Inc., including software and font technology.
Per the terms of the GPL or LGPL, a copy of the source code governed by the GPL or LGPL, as applicable, is available upon request by the End
User. Please contact Fujitsu Limited or Sun Microsystems, Inc.
This distribution may include materials developed by third parties.
Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark
in the U.S. and in other countries, exclusively licensed through X/Open Company, Ltd.
Sun, Sun Microsystems, the Sun logo, Java, Netra, Solaris, Sun Ray, Answerbook2, docs.sun.com, OpenBoot, and Sun Fire are trademarks or
registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.
Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited.
All SPARC trademarks are used under license and are registered trademarks of SPARC International, Inc. in the U.S. and other countries.
Products bearing SPARC trademarks are based upon architecture developed by Sun Microsystems, Inc.
SPARC64 is a trademark of SPARC International, Inc., used under license by Fujitsu Microelectronics, Inc. and Fujitsu Limited.
The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges
the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun
holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN
LOOK GUIs and otherwise comply with Sun’s written license agreements.
United States Government Rights - Commercial use. U.S. Government users are subject to the standard government user license agreements of
Sun Microsystems, Inc. and Fujitsu Limited and the applicable provisions of the FAR and its supplements.
Disclaimer: The only warranties granted by Fujitsu Limited, Sun Microsystems, Inc. or any affiliate of either of them in connection with this
document or any product or technology described herein are those expressly set forth in the license agreement pursuant to which the product
or technology is provided. EXCEPT AS EXPRESSLY SET FORTH IN SUCH AGREEMENT, FUJITSU LIMITED, SUN MICROSYSTEMS, INC.
AND THEIR AFFILIATES MAKE NO REPRESENTATIONS OR WARRANTIES OF ANY KIND (EXPRESS OR IMPLIED) REGARDING SUCH
PRODUCT OR TECHNOLOGY OR THIS DOCUMENT, WHICH ARE ALL PROVIDED AS IS, AND ALL EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE
EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID. Unless otherwise expressly set forth in such agreement, to the
extent allowed by applicable law, in no event shall Fujitsu Limited, Sun Microsystems, Inc. or any of their affiliates have any liability to any
third party under any legal theory for any loss of revenues or profits, loss of use or data, or business interruptions, or for any indirect, special,
incidental or consequential damages, even if advised of the possibility of such damages.
DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT,
ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.
Copyright 2007 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, Etats-Unis. Tous droits réservés.
Entrée et revue tecnical fournies par FUJITSU LIMITED sur des parties de ce matériel.
Sun Microsystems, Inc. et Fujitsu Limited détiennent et contrôlent toutes deux des droits de propriété intellectuelle relatifs aux produits et
technologies décrits dans ce document. De même, ces produits, technologies et ce document sont protégés par des lois sur le copyright, des
brevets, d’autres lois sur la propriété intellectuelle et des traités internationaux. Les droits de propriété intellectuelle de Sun Microsystems, Inc.
et Fujitsu Limited concernant ces produits, ces technologies et ce document comprennent, sans que cette liste soit exhaustive, un ou plusieurs
des brevets déposés aux États-Unis et indiqués à l’adresse http://www.sun.com/patents de même qu’un ou plusieurs brevets ou applications
brevetées supplémentaires aux États-Unis et dans d’autres pays.
Ce document, le produit et les technologies afférents sont exclusivement distribués avec des licences qui en restreignent l’utilisation, la copie,
la distribution et la décompilation. Aucune partie de ce produit, de ces technologies ou de ce document ne peut être reproduite sous quelque
forme que ce soit, par quelque moyen que ce soit, sans l’autorisation écrite préalable de Fujitsu Limited et de Sun Microsystems, Inc., et de leurs
éventuels bailleurs de licence. Ce document, bien qu’il vous ait été fourni, ne vous confère aucun droit et aucune licence, expresses ou tacites,
concernant le produit ou la technologie auxquels il se rapporte. Par ailleurs, il ne contient ni ne représente aucun engagement, de quelque type
que ce soit, de la part de Fujitsu Limited ou de Sun Microsystems, Inc., ou des sociétés affiliées.
Ce document, et le produit et les technologies qu’il décrit, peuvent inclure des droits de propriété intellectuelle de parties tierces protégés par
copyright et/ou cédés sous licence par des fournisseurs à Fujitsu Limited et/ou Sun Microsystems, Inc., y compris des logiciels et des
technologies relatives aux polices de caractères.
Par limites du GPL ou du LGPL, une copie du code source régi par le GPL ou LGPL, comme applicable, est sur demande vers la fin utilsateur
disponible; veuillez contacter Fujitsu Limted ou Sun Microsystems, Inc.
Cette distribution peut comprendre des composants développés par des tierces parties.
Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque
déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd.
Sun, Sun Microsystems, le logo Sun, Java, Netra, Solaris, Sun Ray, Answerbook2, docs.sun.com, OpenBoot, et Sun Fire sont des marques de
fabrique ou des marques déposées de Sun Microsystems, Inc. aux Etats-Unis et dans d’autres pays.
Fujitsu et le logo Fujitsu sont des marques déposées de Fujitsu Limited.
Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc.
aux Etats-Unis et dans d’autres pays. Les produits portant les marques SPARC sont basés sur une architecture développée par Sun
Microsystems, Inc.
SPARC64 est une marques déposée de SPARC International, Inc., utilisée sous le permis par Fujitsu Microelectronics, Inc. et Fujitsu Limited.
L’interface d’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun
reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou graphique
pour l’industrie de l’informatique. Sun détient une license non exclusive de Xerox sur l’interface d’utilisation graphique Xerox, cette licence
couvrant également les licenciés de Sun qui mettent en place l’interface d’utilisation graphique OPEN LOOK et qui, en outre, se conforment
aux licences écrites de Sun.
Droits du gouvernement américain - logiciel commercial. Les utilisateurs du gouvernement américain sont soumis aux contrats de licence
standard de Sun Microsystems, Inc. et de Fujitsu Limited ainsi qu’aux clauses applicables stipulées dans le FAR et ses suppléments.
Avis de non-responsabilité: les seules garanties octroyées par Fujitsu Limited, Sun Microsystems, Inc. ou toute société affiliée de l’une ou l’autre
entité en rapport avec ce document ou tout produit ou toute technologie décrit(e) dans les présentes correspondent aux garanties expressément
stipulées dans le contrat de licence régissant le produit ou la technologie fourni(e). SAUF MENTION CONTRAIRE EXPRESSÉMENT
STIPULÉE DANS CE CONTRAT, FUJITSU LIMITED, SUN MICROSYSTEMS, INC. ET LES SOCIÉTÉS AFFILIÉES REJETTENT TOUTE
REPRÉSENTATION OU TOUTE GARANTIE, QUELLE QU’EN SOIT LA NATURE (EXPRESSE OU IMPLICITE) CONCERNANT CE
PRODUIT, CETTE TECHNOLOGIE OU CE DOCUMENT, LESQUELS SONT FOURNIS EN L’ÉTAT. EN OUTRE, TOUTES LES CONDITIONS,
REPRÉSENTATIONS ET GARANTIES EXPRESSES OU TACITES, Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE À
LA QUALITÉ MARCHANDE, À L’APTITUDE À UNE UTILISATION PARTICULIÈRE OU À L’ABSENCE DE CONTREFAÇON, SONT
EXCLUES, DANS LA MESURE AUTORISÉE PAR LA LOI APPLICABLE. Sauf mention contraire expressément stipulée dans ce contrat, dans
la mesure autorisée par la loi applicable, en aucun cas Fujitsu Limited, Sun Microsystems, Inc. ou l’une de leurs filiales ne sauraient être tenues
responsables envers une quelconque partie tierce, sous quelque théorie juridique que ce soit, de tout manque à gagner ou de perte de profit,
de problèmes d’utilisation ou de perte de données, ou d’interruptions d’activités, ou de tout dommage indirect, spécial, secondaire ou
consécutif, même si ces entités ont été préalablement informées d’une telle éventualité.
LA DOCUMENTATION EST FOURNIE “EN L’ETAT” ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES EXPRESSES
OU TACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE, Y COMPRIS NOTAMMENT
TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A L’APTITUDE A UNE UTILISATION PARTICULIERE OU A
L’ABSENCE DE CONTREFACON.
v
Contents
Preface xvii
1. Introduction to Server Software and Configuration 1
XSCF Firmware 1
Solaris OS Software 2
Software Services 3
Preparing for System Configuration 4
Information Needed 4
Initial Configuration Tasks 5
Related Information 5
2. Access Control 7
About Access Control 7
Logging in to the System 8
XSCF User Accounts 8
XSCF Passwords 9
Privileges 9
XSCF Firmware Update 11
XSCF Shell Procedures for Access Control 11
To Log in Initially to the XSCF Console 12
vi SPARC Enterprise Mx000 Servers Administration Guide April 2007
To Add an XSCF User Account 14
To Create a Password for an XSCF User 14
To Configure an XSCF Password Policy 14
To Assign Privileges to an XSCF User 15
To Display the Version of Installed Firmware 15
Related Information 16
3. System Configuration 17
About System Services 17
DSCP Network Between a Service Processor and a Domain 18
XSCF Network Interfaces 19
Domain Name Service 21
LDAP Service 21
Time Synchronization and NTP Service 23
SNMP Service 24
Additional Services 25
HTTPS Service 26
Telnet Service 26
SMTP Service 26
SSH Service 26
Altitude Setting 26
XSCF Shell Procedures for System Configuration 27
To Configure the DSCP Network 28
To Display DSCP Network Configuration 29
To Configure the XSCF Network Interfaces 29
To Configure the XSCF Network Route Information 30
To Set Or Reset the XSCF Network 31
To Display XSCF Network Configuration 31
To Set the Service Processor Host Name and DNS Domain Name 32
Contents vii
To Set the Service Processor’s DNS Name Server 33
To Enable or Disable Use of an LDAP Server for Authentication and
Privilege Lookup 33
To Configure the Service Processor as an LDAP Client 34
To Set the NTP Configuration 34
To Display the NTP Configuration 35
To Set the Timezone, Daylight Saving Time, Date, and Time Locally on the
Service Processor 35
To Create a USM User Known to the SNMP Agent 36
To Display USM Information for the SNMP Agent 37
To Create a VACM Group 38
To Create a VACM View 38
To Give a VACM Group Access to a VACM View 38
To Display VACM Information for the SNMP Agent 39
To Configure the SNMP Agent to Send Version 3 Traps to Hosts 39
To Enable the SNMP Agent 40
To Display SNMP Agent Configuration 40
To Enable or Disable the Service Processor HTTPS Service 41
To Enable or Disable the Service Processor Telnet Service 42
To Configure the Service Processor SMTP Service 42
To Enable or Disable the Service Processor SSH Service 42
To Generate a Host Public Key for SSH Service 43
To Set the Altitude on the Service Processor 43
Related Information 44
4. Domain Configuration 45
About Domains 45
Domains and System Boards 46
Domain Resource Assignment 50
Domain Component List and Logical System Boards 51
viii SPARC Enterprise Mx000 Servers Administration Guide April 2007
Overview of Steps for Domain Configuration 51
Domain Configuration Example 52
Domain Communication 54
DSCP Network 55
Accessing a Domain Console from the Service Processor 55
Logging in Directly to a Domain 55
DVD Drive or Tape Drive Assignment 55
Backup and Restore Operations 56
Dynamic Reconfiguration 56
XSCF Shell Procedures for Domain Configuration 56
To Specify the XSB Mode 56
To Set Up a Domain Component List 57
To Assign an XSB to a Domain 57
To Power On a Domain 57
To Display System Board Status 58
To Access a Domain From the XSCF Console 58
To Attach a DVD or Tape Drive While the Solaris OS Is Running
(M8000/M9000 Servers) 59
To Disconnect a DVD or Tape Drive While the Solaris OS Is Running
(M8000/M9000 Servers) 59
Related Information 61
5. Audit Configuration 63
About Auditing 63
Audit Records 64
Audit Events 64
Audit Classes 65
Audit Policy 65
Audit File Tools 65
XSCF Shell Procedures for Auditing 66
Contents ix
To Enable or Disable Writing of Audit Records to the Audit Trail 66
To Configure an Auditing Policy 66
To Display Whether Auditing is Enabled Or Disabled 67
To Display Current Auditing Policy, Classes, or Events 67
Related Information 67
6. Log Archiving Facility 69
About Log Archiving 69
Using the Log Archiving Facility 69
Archive Host Requirements 71
Log Archiving Errors 71
Using the snapshot Tool 71
Solaris OS Procedures for Log Archiving 72
To Configure the Log Archive Host 72
XSCF Shell Procedures for Log Archiving 72
To Enable Log Archiving 72
To Disable Log Archiving 73
To Display Log Archiving Configuration and Status 73
To Display Log Archiving Error Details 73
Related Information 74
7. Capacity on Demand 75
About Capacity on Demand 75
COD Boards 76
COD License Purchase 76
License Installation 77
License Allocation 77
Headroom Management 78
License Violations 79
x SPARC Enterprise Mx000 Servers Administration Guide April 2007
XSCF Shell Procedures for Using COD 79
To Install a COD License 79
To Delete a COD License 80
To Reserve Licenses for Allocation 81
To Increase or Decrease Headroom 82
To Disable Headroom 83
To Display COD Information 83
To Display COD License Status 84
To Display Usage Statistics for COD Resources 85
Related Information 87
A. Mapping Device Path Names 89
Glossary 99
Index 103
xi
Figures
FIGURE 2-1 Location of the Operator Panel MODE Switch on a Midrange Server 12
FIGURE 2-2 Operator Panel on a High-end Server 13
FIGURE 3-1 Relationship of the Service Processor and the DSCP Network to the Domains 18
FIGURE 4-1 A Physical System Board in Uni-XSB Mode on an M4000 Midrange Server 46
FIGURE 4-2 A Physical System Board in Uni-XSB Mode on a High-End Server 47
FIGURE 4-3 A Physical System Board in Quad-XSB Mode on a Midrange Server 48
FIGURE 4-4 A Physical System Board in Quad-XSB Mode on a High-End Server 48
FIGURE 4-5 Example of XSBs and Solaris Domains on a High-End Server 49
FIGURE 6-1 Log Archiving 70
xii SPARC Enterprise Mx000 Servers Administration Guide April 2007
xiii
Tables
TABLE 1-1 Software Services 3
TABLE 2-1 User Privileges 10
TABLE 3-1 XSCF Network Interfaces 20
TABLE 3-2 LDAP LDIF File Attributes 22
TABLE 3-3 XSCF and Domain Time Synchronization 23
TABLE 4-1 Boards, Domains, and Domain ID Numbers 49
TABLE 4-2 Resource Assignment in Quad-XSB Mode on an M4000 Midrange Server 50
TABLE 4-3 Resource Assignment in Quad-XSB Mode on an M5000 Midrange Server 50
TABLE 4-4 Resource Assignment in Quad-XSB Mode on a High-end Server 51
TABLE A-1 LSB Numbers and Starting Processor Numbers 90
TABLE A-2 LSB Numbers and Device Path Values 92
TABLE A-3 I/O Device Mapping on a Midrange Server 93
TABLE A-4 Internal Devices and Device Paths on the M4000 and M5000 Servers 93
TABLE A-5 Internal Devices and Device Paths on the M5000 Server 94
TABLE A-6 I/O Device Mapping on a High-end Server 94
TABLE A-7 Internal Devices and Device Paths on a High-end Server 95
TABLE A-8 cfgadm Device Matrix for Midrange Servers 97
TABLE A-9 cfgadm Device Matrix for High-End Servers 98
xiv SPARC Enterprise Mx000 Servers Administration Guide April 2007
xv
Code Samples
CODE EXAMPLE 3-1 LDAP Schema 22
CODE EXAMPLE 3-2 Sample LDAP LDIF File Attributes 22
CODE EXAMPLE 3-3 Sample ntp.conf File for a Domain using XSCF as NTP Server 24
xvi SPARC Enterprise Mx000 Servers Administration Guide April 2007
Preface xvii
Preface
The SPARC Enterprise M4000/M5000/M8000/M9000 Servers Administration Guide
describes the system configuration procedures, which focuses on the initial settings
of the SPARC Enterprise M4000/M5000/M8000/M9000 servers. This document
describes the settings of service processors which embedded in the SPARC
Enterprise M4000/M5000/M8000/M9000 servers and also refers to the settings of
the Solaris
TM
Operating System, accompanied by the service processors settings.
This document targets at every model of the SPARC Enterprise
M4000/M5000/M8000/M9000 servers; however, in some parts, describes the content
specific to the model, such as the midrange (SPARC Enterprise M4000/M5000)
servers or the high-end (SPARC Enterprise M8000/M9000) servers. Please refer to
the part relevant to the model in use.
To better understand the content of this document, it is recommended to read the
following manuals together.
About the hardware:
The SPARC Enterprise M8000/M9000 Servers Overview Guide or the SPARC
Enterprise M4000/M5000 Servers Overview Guide
About the eXtended System Control Facility (XSCF) firmware in the service
processor:
SPARC Enterprise M4000/M5000/M8000/M9000 Servers XSCF Users Guide
SPARC Enterprise M4000/M5000/M8000/M9000 Servers XSCF Reference Manual
This section includes:
“Audience” on page xviii
“Structure and Contents of This Manual” on page xviii
“SPARC Enterprise Mx000 Servers Documentation” on page xix
“Abbreviated References to Other Documents” on page xxii
“Models” on page xxiii
“Text Conventions” on page xxiii
“Prompt Notations” on page xxiv
“Syntax of the Command Line Interface (CLI)” on page xxiv
“Software License” on page xxv
xviii SPARC Enterprise Mx000 Servers Administration Guide April 2007
“Fujitsu Welcomes Your Comments” on page xxv
Audience
This manual is intended for users, who administrate SPARC Enterprise
M4000/M5000/M8000/M9000 servers (hereinafter referenced to as XSCF user). The
XSCF user is required to have the following knowledge:
Solaris
TM
Operating System and Unix command
SPARC Enterprise M4000/M5000/M8000/M9000 servers and basic knowledge of
XSCF
Structure and Contents of This Manual
This manual is organized as described below:
Chapter 1
This chapter provides an introduction to the system software and
configuration.
Chapter 2
This chapter describes access control, including log in, user accounts,
passwords, and privileges.
Chapter 3
This chapter describes initial configuration of services and networks.
Chapter 4
This chapter contains information on domains and domain communication.
Chapter 5
This chapter describes auditing functionality.
Chapter 6
This chapter describes the log archiving feature.
Chapter 7
This chapter covers capacity on demand (COD) and licenses.
Appendix A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138

Fujitsu M8000 Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues