EarthWise CVPS43010 Le manuel du propriétaire

OWNER’S MANUAL

ELECTRIC CONVERTIBLE 2 IN 1 COMBO

CHAIN SAW/ POLE SAW

This product has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the owner’s manual before

using this product.

Thank you for your purchase.

DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING, ASSEMBLY,

PARTS, SERVICE QUESTIONS? GO TO WWW.AMERICANLAWNMOWER.COM

OR CALL 1-800-313-5111 BETWEEN 8:00 AM—5:00 PM EST FOR ASSISTANCE.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Model CVPS43010

GENERAL POWER TOOL SAFETY WARNINGS

IMPORTANT SAFETY WARNINGS

2

Model CVPS43010

WARNING: Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

• Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust

or fumes.

• Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodified plugs

and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces the risk

of electric shock.

Personal safety

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in

serious personal injury.

• Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

• Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invites accidents.

• Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

• Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

• Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

3

Model CVPS43010

GENERAL POWER TOOL SAFETY WARNINGS

• Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Service

• Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

• When servicing a power tool, use only identical

replacement parts. Follow instructions in the

Maintenance section of this manual. Use of

unauthorized parts or failure to follow Maintenance

instructions may create a risk of shock or injury.

CHAIN SAW SAFETY WARNINGS

• Keep all parts of the body away from the saw chain

when the chain saw is operating. Before you start the

chain saw, make sure the saw chain is not contacting

anything. A moment of inattention while operating chain

saws may cause entanglement of your clothing or body

with the saw chain.

• Always hold the chain saw with your right hand on the

rear handle and your left hand on the front handle.

Holding the chain saw with a reversed hand configuration

increases the risk of personal injury and should never be

done.

• Hold the power tool by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring or its own cord. Saw chains contacting a live wire

may make exposed metal parts of the power tool live and

could give the operator an electric shock.

• Wear safety glasses and hearing protection. Further

protective equipment for head, hands, legs and feet is

recommended. Adequate protective clothing will reduce

personal injury by flying debris or accidental contact with

the saw chain.

• Do not operate a chain saw in a tree. Operation of a

chain saw while up in a tree may result in personal injury.

• Always keep proper footing and operate the chain saw

only when standing on fixed, secure and level surface.

Slippery or unstable surfaces such as ladders may cause a

loss of balance or control of the chain saw.

• When cutting a limb that is under tension be alert for

spring back. When the tension in the wood fibres is

released the spring loaded limb may strike the operator

and/or throw the chain saw out of control.

• Use extreme caution when cutting brush and saplings.

The slender material may catch the saw chain and be

whipped toward you or pull you off balance.

• Carry the chain saw by the front handle with the chain

saw switched off and away from your body. When

transporting or storing the chain saw always fit the

guide bar cover. Proper handling of the chain saw will

reduce the likelihood of accidental contact with the moving

saw chain.

• Follow instructions for lubricating, chain tensioning

and changing accessories. Improperly tensioned or

lubricated chain may either break or increase the chance

for kickback.

• Keep handles dry, clean, and free from oil and grease.

Greasy, oily handles are slippery causing loss of control.

• Cut wood only. Do not use chain saw for purposes

not intended. For example: do not use chain saw for

cutting plastic, masonry or non-wood building

materials. Use of the chain saw for operations different

than intended could result in a hazardous situation.

Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinch-

es the saw chain in the cut.

Tip contact in some cases may cause a sudden reverse

reaction, kicking the guide bar up and back towards the

operator.

Pinching the saw chain along the top of the guide bar

may push the guide bar rapidly back towards the

operator.

Either of these reactions may cause you to lose control of

the saw which could result in serious personal injury. Do

not rely exclusively upon the safety devices built into your

saw. As a chain saw user, you should take several steps

to keep your cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below:

• Maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both hands on

the saw and position your body and arm to allow you

to resist kickback forces. Kickback forces can be

controlled by the operator, if proper precautions are tak-

en. Do not let go of the chain saw.

• Do not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact and

enables better control of the chain saw in unexpected

situations.

• Only use replacement bars and chains specified by

the manufacturer. Incorrect replacement bars and

chains may cause chain breakage and/or kickback.

• Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to increased

kickback.

EXTENSION CORD. Make sure your extension cord is in

good condition. When using an extension cord, be sure it is

heavy enough to carry the current your product will draw. An

undersized extension cord will cause a drop in line voltage

resulting in loss of power and overheating. The following

table shows the correct size to use depending on cord length

and nameplate ampere rating. If in doubt, use the next

heavier gage. The smaller the gage number, the heavier the

cord.

WARNING: Use out door extension cords marked SW-A,

SOW-A, STW-A, SJW-A, or SJTW-A. These cords are rated

for outdoor use and reduce the risk of electric shock.

DOUBLE INSULATION—Double Insulation is a concept in

safety in electric power tools, which eliminates the need for

the usual three-wire grounded power cord. All exposed metal

parts are isolated from the internal metal motor components

with protecting insulation. Double insulated tools do not need

to be grounded.

NOTE: The double insulated system is intended to protect

the user from shock resulting from a break in the tool’s

internal insulation. Observe all normal safety precautions to

avoid electrical shock.

It is possible to tie the extension cord and

power cord in a knot to prevent them from

becoming disconnected during use. Make

the knot as shown, then connect the plug

end of the power cord into the receptacle

end of the extension cord,. This method can also be used to

tie two extension cords together.

POLARIZED PLUGS—To reduce the risk of electric shock,

this equipment has a polarized plug (one blade is wider than

the other). This equipment must be used with a suitable

polarized 2 wire or 3 wire extension cord. Polarized

connections will fit together only one way. Make sure that the

receptacle end of the extension cord has large and small

blade slot widths. If the plug does not fit fully into the

extension cord, reverse the plug. If it still does not fit obtain a

suitable extension cord. If the extension cord does not fit fully

into the outlet, contact a qualified electrician to install the

proper outlet. Do not change the tool plug or extension cord in

any way.

CHECK DAMAGED PARTS – Before further use of the tools,

a guard or other part that is damaged should be carefully

checked to determine that it will operate properly and perform

its intended function. Check for alignment of moving parts,

binding of moving parts, breakage of parts, mounting and any

other condition that may affect its operation. A guard or other

part that is damaged should be properly repaired or replaced.

Call our customer service help line at 1-800-313-5111 for

assistance.

WARNING: California Proposition 65: This product contains

chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm.

WARNING: Some dust and debris created by this tool could

contain chemicals known to the State of California to cause

cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

-chemicals in fertilizers

-compounds in insecticides, herbicides and pesticides

-arsenic and chromium from chemically treated lumber

Your risk of exposure to these chemicals varies depending on

how often you do this type of work. To reduce your exposure,

work in a well ventilated area and with approved safety

equipment such as dust masks that are specially designed to

filter out microscopic particles.

WARNING: Cancer and Reproductive Harm -

www.P65Warnings.ca.gov.

CAUTION: Never stand under the limb being trimmed.

Position yourself out of the way of falling debris.

Minimum Gage for Cord Sets

Volts Total Length of cord in Feet

120V 0-25 26-50 51-100 101-150

Ampere Rating

More Not More American wire Gage

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

4

Model CVPS43010

Telescopic Pole - Bar Cover

PRODUCT SPECIFICATIONS

CVPS43010

Input….………………………….….……..………………….….…………….………….….…………….…….…. 120V, 60Hz, 7A, AC Only

Speed ………………………..……………...…………………...……………………………………….……………………….………..12m/s

Bar Length……………………………...…...……..…………………………………………….………………………..…..10 in. Oregon Bar

Extended Length…………...………………..………...…………. ……………………………………………….………….….…………… 8 ft.

Weight ……………………………….……………………….. ………………………………………………………………………..…10.27 Ibs

Chain

Guide Bar

Hand Guard

Front Handle

Oil Tank Cap

Quick Release Button

Tension Knob

Shoulder Strap

Quick Release Button

Locking Collar Angle Adjustment Button

Safety Button

Trigger Switch

Bar Cover

Chain Cover

5

Model CVPS43010

PACKING LIST

− Chain Saw Cutting Head

− Blade Cover

− Telescopic Pole w/Should Strap

− Rear Handle

− Owner’s Manual

WARNING: If any parts are damaged or missing, do not operate this

product until the parts are replaced. Failure to heed this warning

could result in serious personal injury.

If any parts are damaged or missing, please call 1-800-313-5111 for

assistance.

UNPACKING

This product requires assembly.

Carefully remove the product and any accessories from the box.

Make sure that all items listed in the packing list are included.

Inspect the product carefully to make sure no breakage or damage

occurred during shipping.

Do not discard the packing material until you have carefully inspected

and satisfactorily operated the product.

ASSEMBLY

CONVERTING FROM CHAIN SAW TO POLE SAW

1. Lift the quick release button. Pull to remove the handle from the

cutting head. (Fig. 1)

2. Insert the telescopic pole into the chain saw cutting head. Press

down the quick release button. Make sure the release button

snaps firmly to lock the parts securely. (Fig. 2)

3.

Insert the rear handle into the end of the telescopic pole. (Fig. 3)

Press down the quick release button. Ensure the release button

snaps firmly into position to lock the handle securely.

CONVERTING FROM POLE SAW TO CHAIN SAW

1. Disconnect rear handle and cutting head from ends of

telescopic pole by lifting the quick release button and pulling

straight out. (Fig. 4-5)

2. Insert the rear handle directly into the chainsaw cutting head .

When fully inserted, press down the quick release button.

Make sure the button snaps in firmly and securely, locking the

parts together.

Pole

FIG. 2

Quick Release

Button

FIG. 3

Pole

Rear

Handle

FIG. 1

Quick release button

Rear handle

ADJUSTING THE LENGTH OF THE TELESCOPIC POLE (FIG.6 )

1. To adjust the telescopic pole, disconnect the product from

the power supply. Rotate the collar counterclockwise to

loosen, Extend the pole to the desired length.

NOTE: Only extend the pole to minimum length required to

reach the limb or shrub to be cut.

2. Lock the pole in position by turning the collar clockwise

firmly to secure.

WARNING: Failure to lock the telescopic pole collars as directed

could result in personal injury.

Locking

Collar

FIG.6

6

Model CVPS43010

4. Remove the bar and chain from the mounting surface.

5. Remove the old chain from the bar.

6. Lay out the new chain in a loop, and straighten any

kinks. The cutters should face in the direction of the

chain rotation. If they face backwards, turn the loop

over.(Fig. 8)

INSTALLING/REPLACING THE GUIDE BAR AND CHAIN

DANGER: Never start the motor before installing the guide bar,

chain, chain cover and tension knob. Without all these parts in

place, the clutch can fly off or explode, exposing the user to

possible serious injury.

WARNING: To avoid serious personal injury, read and

understand all the safety instructions provided.

WARNING: Before performing any maintenance, make sure

the tool is unplugged from the power supply. Failure to heed

this warning could result in serious personal injury.

CATUION: Always wear gloves when handling the bar and

chain; these components are sharp and may contain burrs,

which can cause serious injury.

WARNING: Never touch or adjust the chain while the motor

is running. The saw chain is very sharp. Always wear

protective gloves when performing maintenance to the chain

to avoid possible serious lacerations.

NOTE: When replacing the guide bar and chain, use only

identical replacement parts.

1. Disconnect the saw from power supply.

2. Loosen the tension knob by turning counterclockwise.

3. Remove the chain cover.(Fig. 7)

7. Place the chain drive links into the bar groove.

NOTE: Make certain of the direction of chain.

8. Position the chain so there is a loop at the back of the bar.

(Fig. 9)

9. Hold the chain in position on the bar and place the loop

around the sprocket.(Fig. 10)

FIG. 7

FIG. 9

FIG. 10

Chain cover

Tension knob

10. Fit the bar flush against the mounting surface so that the bar

stud is in the slot of the bar.

NOTE: When placing the bar on the bar stud, ensure that the

adjusting pin is in the chain tension pin hole.

11. Replace the chain cover.

12. Tighten the tension knob. Remove all slack from the chain by

turning the knob clockwise until the chain seats snugly against

the bar with the drive links in the bar groove. (Fig. 11)

Cutter Direction

FIG. 8

Tension knob

FIG.11

13. When the tension knob is fully tightened, the chain is the

tightest. If the chain is too tight, it will not rotate. To minor adjust

the chain tension, loosen the tension knob by turning it

counter-clockwise slightly until the chain is correctly tensioned.

NOTE: The chain is correctly tensioned when there is no sag on the

underside of the guide bar, then chain is snug, but it can be turned by

hand without binding.

NOTE: A new chain tends to stretch, check chain tension

frequently and tension as required.

14. After a period of usage, the chain may get loose. To tighten the

chain, loosen the tension knob by turning counter-clockwise,

Repeat 12 and 13 to correctly adjust the chain tension.

7

Model CVPS43010

CHAIN TENSION AND MAINTENANCE

CHAIN TENSION

Stop the motor before setting the chain tension. Make sure the

tension knob is loosened to finger tight, turn the tension knob

clockwise to tension the chain. A cold chain will be correctly tensioned

when there is no slack on the underside of the guide bar, the chain is

snug, but it can be turned by hand without binding.

Chain must be re-tensioned whenever the flats on the drive links hang

out of the bar groove.

During normal saw operation, the temperature of the chain will

increase. The drive links of a correctly tensioned warm chain will hang

approximately .050 in. (1.25mm) out of the bar groove. (Fig. 12) Be

aware that chain tensioned while warm, may be too tight upon

cooling. Check the “cold tension” before next use.

NOTE: A new chain tends to stretch, check chain tension frequently

and tension as required.

Approx. .050 (1.25mm)

CHAIN MAINTENANCE

CAUTION: Disconnect the saw from the power supply and make sure

the chain has stopped before you do any work on the saw.

For smooth and fast cutting, chain needs to be maintained properly.

The chain requires sharpening when the wood chips are small and

powdery, the chain must be forced through the wood during cutting,

or the chain cuts to one side. During maintenance of your chain

remember:

- Improper filing angle of the side plate can increase the risk

of severe kickback.

- Raker (depth gauge) clearance.

- Too low increases the potential for kickback.

- Not low enough decreases cutting ability.

- If cutter teeth have hit hard objects such as nails and stones, or

have been abraded by mud or sand on the wood, have service

dealer sharpen chain.

NOTE: Inspect the drive sprocket for wear or damage when

replacing the chain. If signs of wear or damage are present in the

areas indicated, have the drive sprocket replaced by a qualified

individual.

FIG.12

FIG.13

Cutting

Corner

Top Plate

Rivet Hole

Heel

Gullet

Toe

Depth Gauge

Side Plate

HOW TO SHARPEN THE CUTTERS

Be careful to file all cutters to the specified angles and to the same

length, as fast cutting can be obtained only when all cutters are

uniform.

Wear gloves for protection. Properly tension the chain prior to

sharpening. Refer to “Chain Tension Section” earlier in this manual.

Do all of your filing at the midpoint of the bar.

Use a 5/32 in. diameter round file and holder.

Keep the file level with the top plate of the tooth. Do not let the file dip

or rock. Using light but firm pressure, stroke towards the front corner

of the tooth. (Fig. 13)

Lift file away from the steel on each return stroke.

Put a few firm strokes on every tooth. File all left hand cutters in

one direction. Then move to the other side and file the right

hand cutters in the opposite direction. Occasionally remove

filing from the file with a wire brush. (Fig. 14)

WARNING: Improper chain sharpening increases the potential

of kickback.

WARNING: Failure to replace or repair damaged chain can

cause serious injury.

Right Hand Cutters

Left Hand Cutters

FIG.14

8

Model CVPS43010

CHAIN TENSION AND MAINTENANCE

Use a flat file and a depth gauge jointer to lower all gauges uniformly.

Depth gauge jointers are available in .020 in. to .035 in. (0.5 mm to

0.9 mm). Use a .025 in. (0.6 mm) depth gauge jointer. After lowering

each depth gauge, restore original shape by rounding the front. Be

careful not to damage adjoining drive links with the edge of the file.

Depth gauges must be adjusted with the flat file in the same direction

the adjoining cutter was filed with the round file. Use care not to

contact cutter face with flat file when adjusting depth gauges.

WARNING: The saw chain is very sharp, always wear protective

gloves when performing maintenance to the chain.

TOP PLATE FILING ANGLE (Fig. 15)

Correct 30 degrees – File holders are marked with guide marks to

align file properly to produce top plate angle.

Less than 30 degrees – for cross cutting.

More than 30 degrees – feathered edge dulls quickly.

SIDE PLATE ANGLE (Fig. 16)

Correct – 80 degrees produced automatically if correct diameter file is

used in file holder.

Hook – “Grabs” and dulls quickly. Increases potential of kickback.

Results from using a file with a diameter too small or file held too low.

Backward Slope – Needs too much feed pressure, causes

excessive wear to bar and chain. Results from using a file with a

diameter too large, or file held too high.

DEPTH GAUGE CLEARANCE (Fig. 17)

The depth gauge should be maintained at a clearance of .025 in. (0.6

mm). Use a depth gauge tool for checking the depth gauge

clearances.

Every time the chain is filed, check the depth gauge clearance.

FIG.15

FIG.16

FIG.17

CORRECT TOP PLATE

FILING ANGLE

INCORRECT TOP PLATE FILING

ANGL

LESS THAN

30°

MORE THAN

30°

CORRECT SIDE

PLATE FILING

ANGLE

INCORRECT SIDE PLATE

FILING ANGL

HOOK BACKWARD

SLOPE

RAKER CLEARANCE

.025 in. (0.6mm)

DEPTH GAUGE JOINTER

FLAT FILE

RESTORE ORIGIINAL

SHAPE BY ROUNDING

THE FRONT

9

Model CVPS43010

ADJUSTING THE ANGLE OF POLE SAW HEAD (Fig. 20)

1. To adjust the sawing angle, press the angle adjustment button.

2. Turn the saw to the desired angle.

3. The angle can be adjusted between -20 and 60 degrees.

Before you start the unit, make sure the pole/chain saw is not

contacting any object.

STARTING THE POLE/CHAIN SAW

Push the safety button in with your thumb and then squeeze the

switch trigger with your fingers. Once the tool is running, you can

release the safety button. To turn the tool OFF, release the switch

trigger. (Fig. 18)

WARNING: To guard against injury, observe the following:

− Read instruction manual before using.

− Save instruction manual.

− Keep hands away from blades.

− Keep hands on handles. Don’t overreach.

A good, firm grip on the pole/ chain saw with both hands will help you

maintain control. Grip the rear handle with your right hand whether

you are right or left handed. Wrap the fingers of your left hand over

and around the front handle when using the chainsaw, or around the

pole shaft when using the pole saw. A firm grip together with

positioning handle against your body will help you maintain control of

the saw. Don’t let go.

WARNING: Do not operate pole saw in a tree, on a ladder, or on a

scaffold; this is extremely dangerous.

CAUTION: Chain coasts after pole saw is turned off. Do not use

under wet conditions.

Use extreme caution when cutting small size brush, saplings or limbs

under tension, because slender and tense material may catch the saw

and be whipped toward you, pull you off balance or spring back.

Do not use saw to cut vines and or small underbrush.

BRAKE

When using the chainsaw, in case an emergency stop is necessary,

use the back of your hand to push the hand guard forward. Chain will

stop immediately. (Fig. 19)

CAUTION: Failure to lubricate the chain will cause damage to the bar

and chain. Use only a good quality bar and chain oil or, if not

available, unused SAE 30 weight motor oil may be substituted. One

minute of use will consume approx. 0.15 fl. oz. (5ml) of oil.

NOTE: It is normal for oil to seep from the chainsaw cutting head

when not in use. To prevent seepage, empty the oil tank after each

use. When storing the unit for a long period of time (3 months or long-

er) be sure the chain is lightly lubricated; this will prevent rust on the

chain and bar sprocket.

OPERATING

WARNING: Kickback may occur when the moving chain contacts an

object at the upper portion of the tip of the guide bar or when the

wood closes in and pinches the chain saw in the cut. Contact at the

upper portion of the tip of the guide bar can cause the chain to dig

into the object and stop the chain for an instant. The result is a

lightening fast, reverse reaction which kicks the guide bar up and

back toward the operator. If the chain saw is pinched along the top of

the guide bar, the guide bar can be driven rapidly back toward the

operator. Either of these reactions can cause loss of saw control

which can result in serious

injury. Do not rely exclusively

upon the safety devices built

into the saw. As a chain saw

user, you should take several

steps to keep your cutting

jobs free from accident or

injury.

The following precautions should be followed to minimize

kickback:

1. Always grip the pole and/or handles firmly with both hands when

unit is running. When using the chainsaw, place your right hand

on the rear handle and your left hand on the front handle with

your thumbs and fingers encircling the chainsaw handles. When

using as a pole saw, place one hand on the pole and your other

hand on the rear handle with your thumbs and fingers encircling

the pole and handle. A firm grip together with positioning handle

against your body will help you maintain control of the saw if

kickback occurs.

2. Make sure that the area in which you are cutting is free from

obstructions. Do not let the nose of the guide bar contact a log,

branch, fence or any other obstruction that could be hit while you

are operating the saw.

3. Always cut with the unit running at full speed. Fully squeeze the

throttle trigger and maintain a steady cutting speed.

4. Wear non-slip gloves for maximum grip protection.

Cut lower branches first to allow the top branches more room to fall.

Work slowly, keeping both hands on the saw with a firm grip.

Maintain secure footing and balance.

WARNING: To protect yourself from electrocution, maintain a min. of

50 ft. (15m) from over head electrical lines.

WARNING:Keep bystanders at least 50 ft. away.

WARNING: Do not cut trees near electrical wires or buildings.If

chain jams on any electrical cord or line, DO NOT TOUCH THE BAR

AND CHAIN. THEY CAN BECOME ELECTRICALLY LIVE AND

VERY DANGEROUS.

WARNING: Do Not use the pole saw with any type of accessory or

attachment. Such usage might be hazardous.

WARNING: Beware of the cord while operating the saw. Keep the

cord away from the chain. Be careful not to trip over the

extension cord.

FIG.18

KICKBACK

DANGER ZONE

Safety Button

Switch Trigger

FIG.20

Angle Adjustment

Button

-20°

20°

40°

60°

Hand Guard

FIG.19

10

Model CVPS43010

OPERATING AND INSTRUCTIONS

PROPER CUTTING STANCE

Weight should be balanced with both feet on solid ground.

Keep left arm with elbow locked in a “straight arm” position to

withstand any kickback force when using pole saw. Your right hand

should be gripping the handle and positioned firmly against body for

added support.

Your body should always be to the left of the chain line.

BASIC CUTTING PROCEDURE

Do not use the pole saw to fell saplings. Use the chain saw without

the pole attachment.

Small trees up to 6-7 inches in diameter are usually cut in a single

cut. Large tree limbs require notch cuts. Notch cuts determine the

direction the tree will fall.

WARNING: If the tree limb starts to fall in the wrong direction, or if

the saw gets caught or hung up during the fall, leave the saw and

save yourself.

WARNING: Periodically glance at the top of the tree during the

back-cut to assure the tree limb is going to fall in the desired

direction.

Practice cutting a few small limbs using the following technique to

get the “feel "of using the saw before you begin a major sawing

operation.

Take the proper stance in front of the wood with the saw in the

“off”position.

Squeeze the trigger and let the chain accelerate to full speed before

entering the cut.

Always hold the saw firmly with both hands.

Keep the unit running the entire time you are cutting, maintain a

steady speed.

Allow the chain to cut for you; exert only light downward pressure. If

you force the cut, damage to the bar, chain, or unit can result in

serious injury.

Do not put pressure on the saw at the end of the cut.

When felling the top of a small tree, keep everyone a safe distance

from the cutting area. During felling operations, the safe distance

should be at lease twice the height of the largest trees in the felling

area.If the tree makes contact with any utility line, the utility company

should be notified immediately.

Always cut with both feet on solid ground to prevent being pulled or

knocked off balance.

Do not extend arms above shoulder level when operating the pole saws.

Do not cut above chest height when using the chain saw.

FELLING A TREE

When bucking and felling operations are being performed by two or

more persons, at the same time, the felling operation should be

separated from the bucking operation by a distance of at least twice

the height of the tree being felled. Trees should not be felled in a

manner that would endanger any person, strike any utility line or

cause any property damage. If the tree does make contact with any

utility line, the utility company should be notified immediately.

Before felling is started, consider the force and direction of the wind, the

lean and balance of the tree, and the location of large limbs. These

things influence the direction in which the tree will fall. Do not try to fell a

tree along the line different from its natural line of fall.

The saw operator should keep on the uphill side of the terrain as the

tree is likely to roll or slide downhill after it is felled.

Remove dirt, stones, loose bark, nails, staples, and wire from the tree

where felling cuts are to be made.

NOTCHED UNDERCUT– Cut a notch about 1/3 diameter of the tree,

perpendicular to the direction of the fall. Make the cuts of the notch so

they intersect at a right angle to the line of fall. This notch should be

cleaned out to leave a straight line. To keep the weight of the wood off

the saw, always make the lower cut of the notch before the upper cut.

WARNING: Do not fell trees during periods of high wind or heavy

precipitation. Wait to do your cutting until the hazard has ended.

WARNING: Do not cut down trees having an extreme lean or large

trees that have rotten limbs, loose bark, or hollow trunks. Have these

trees pushed or dragged down with heavy equipment , then cut them

up.

FELLING BACK-CUT

The back-cut is always made level and horizontal, and at a minimum of

2 inches (5cm) above the horizontal cut of the notch.

Never cut through to the notch. Always leave a band of wood between

the notch and back-cut (approximately 2 inches (5cm) or 1/10 the

diameter of the tree). This is called “ hinge” or “hinge wood”. It controls

the fall of the tree and prevents slipping or twisting or shoot-back of the

tree off the stump.

This saw is not designed to fell large diameter tree tops, or tree trunks.

PLANNED

LINE OF FALL

SAFE

RETREAT

ZONE

SAFE

RETREAT

ZONE

PLANNED LINE OF FALL

SAFE

RETREAT

ZONE

PLANNED PATH OF SAFE RETREAT

135° FROM PLANNED LINE OF FALL

FIG. 21

WARNING: Check the tree for damaged or dead branches that could fall

and hit you during felling.

Before any cuts are started, pick your escape route (or routes in case

the intended route is blocked); clear the immediate area around the tree

and make sure there are no obstructions in your planned path of retreat.

A clear path of safe retreat is approximately 135 degrees from planned

line of fall. The retreat path should extend back and diagonally to the

rear of the expected line of fall.(Fig. 21)

11

Model CVPS43010

OPERATING

CUTTING INSTRUCTIONS

As the tree limbs starts to fall, stop the saw and immediately retreat

along the cleared path. Watch the action in case something falls your

way. Be alert for overhead limbs or branches that may fall and watch

your footing.

WARNING: Never cut through to the notch when making a back-cut.

The hinge controls the fall of the tree, this is a section of wood

between the notch and back-cut.(Fig. 22)

BUCKING

Bucking is the term used for cutting a fallen tree to the desired log

length.

Always make sure your footing is secure and your weight is

distributed evenly on both feet.

Cut only one log at a time, Support small logs on a saw horse or

another log while bucking.

Keep a clear cutting area. Make sure that no objects can contact the

guide bar nose and chain during cutting, this can cause kickback.

When bucking on a slope, always stand on the uphill side of the log.

When “Cutting through”, to maintain complete control of the pole saw,

release the cutting pressure near the end of the cut without relaxing

your grip on the pole saw handles. Do not let the chain contact the

ground After completing the cut, wait for the saw chain to stop before

you move the pole saw. Always stop the motor before moving from

tree to tree.

BUCKING LOGS UNDER STRESS

When the log is supported along its entire length, it should be cut from

the top or over-bucking.

When the log is supported on one end, cut 1/3 diameter from the

underside or under-bucking. Then make the finishing cut by

over-bucking to meet the first cut.

As the log is being cut, it will tend to bend The saw can become

pinched or hung in the log if you make the first cut deeper than 1/3 of

the diameter of the log.

Give special attention to logs under stress to prevent the bar and

chain from pinching.

OVERBUCKING - Begin on the top side of the log with the button of

the saw against the log; exert light pressure downward. Note that the

saw will tend to pull away from you. (Fig. 23)

UNDER-BUCKING - Begin on the under side of the log with the top of

the saw against the log; exert light pressure upward. During

under-bucking, the saw will tend to push back at you. Be prepared for

this reaction and hold the saw firmly to maintain control. (Fig. 23)

LIMBING (Fig. 24)

Limbing is removing branches from a fallen tree.

Work slowly, keeping both hands on the pole saw with a firm grip.

Always make sure your footing is secure and your weight is distributed

evenly on both feet.

Leave the larger support limbs under the tree to keep the tree off the

ground while cutting.

Limbs should be cut one at a time. Remove the cut limbs from the work

area often to help keep the work area clean and safe.

Branches under tension should be cut from the bottom up to avoid

binding the pole saw.

Keep the tree between you and the pole saw while limbing. Cut from the

side of the tree opposite the branch you are cutting.

WARNING: Never climb into a tree to limb or prune. Do not stand on

ladders, platforms, a log, or in any position which can cause you to lose

your balance or control of the saw.

PRUNING (Fig. 25)

Pruning is trimming limbs from a live tree.

Work slowly, keep both hands on

the pole saw with a firm grip and the

handle positioned firmly against your

body for added control and ease of

handling. Always make sure your

footing is secure and your weight is

distributed evenly on both feet.

When pruning trees it is important

not to make the finishing cut next to

the main limb or trunk until you have

cut off the limb further out to reduce

the weight. This prevents stripping

the bark from the main member.

Make first cut six inches from tree trunk as possible on underside of limb

stub. Use top of guide bar to make this cut. Cut 1/3 through diameter of

stub.

Move two to four inches farther out on limb. Make second cut from

above limb. Continue cut until you cut limb off.

Make third cut as close to tree trunk as possible on underside of limb

stub. Use top of guide bar to make this cut. Cut 1/3 through diameter of

stub.

Make fourth cut directly above third cut. Cut down to meet third cut. This

will remove limb stub.

SPRINGPOLES

A spring pole is branch, or sapling which is bent under tension by other

wood so that it springs back if the wood holding it is cut or removed.

WARNING: Watch out for spring poles, they are dangerous, They could

result in severe or fatal injury.

FIG.22

FIG.24

FIG.25

HINGE

2 IN. (5CM) OR 1/10 DIA

BACK CUT

2 IN. (5 CM)

NOTCH

APPROX. 1/3

DIAMETER

OF TRUNK

HINGE

BACK CUT

OVERBUCKING UNDER-BUCKING

LIMBING

CUT LIMBS ONE AT A TIME AND LEAVE SUPPORT

LIMBS UNDER TREE UNTIL LOG IS CUT

3rd Cut-Stub Undercut

(to avoid splintering)

2nd Cut-Pruning

Cut (to avoid

pinching)

1st Cut-Pruning

Undercut (to

avoid splintering)

4th Cut-Final

Stub Cut

PRUNING

Fig. 23

12

Model CVPS43010

BEFORE USING: Fill oil well with new quality bar and chain oil.

Unused SAE30 weight motor oil may be substituted.

If you drop the product, carefully inspect it for damage. If the blade is

bent or cracked, handles broken or if you see any other condition that

may affect the product’s operation, it must be repaired before putting

it back into use. Call our customer service help line at

1-800-313-5111 for assistance.

CAUTION: Do not at any time let brake fluids, gasoline, petroleum

based products, penetrating oils, etc., come in contact with plastic

parts. They contain chemicals that can damage, weaken or destroy

plastic.

Make sure the unit is detached from the power supply, then use only

mild soap and a damp cloth to clean the tool. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment should be performed by a

qualified individual using identical replacement parts only.

Ensure that the plastic bar covers are in place when storing.

For smooth and fast cutting, chain needs to be maintained properly.

The chain requires sharpening when the wood chips are small and

powdery, the chain must be forced through the wood during cutting,

or the chain cuts to one side. Refer to instructions earlier in this

manual for instructions on properly sharpening the chain.

LUBRICATION SYSTEM FOR POLE/CHAIN SAW

The chain is automatically lubricated.

MAINTENANCE

Feathering or burring of the bar rails is a normal process of bar wear.

Such faults should be smoothed with a file as soon as they occur.

A bar with any of the following faults should be replaced.

- Wear inside the bar rails which permits the chain to lay over

side ways.

- Bent guide bar

- Cracked or broken rails

- Spread rails

In addition, guide bars with a sprocket at their tip must be lubricated

frequently with a grease syringe to extend the guide bar life. Using a

grease syringe, lubricate weekly in the lubricating hole.

Turn the guide bar and check that the lubrication holes and chain

groove are free from obstructions.

GUIDE BAR MAINTENANCE

When the guide bar shows signs of wear, reverse it on the saw to

distribute the wear for maximum bar life. The bar should be cleaned

every day of use and checked for wear and damage.

Check oil level before each work session, refill if less than ¼ full.

If the lubrication system does not work properly, check if the oil filter

and all oil-ways are clean and free from obstructions. If it is still not

working, call our customer service help line at 1-800-313-5111 for

assistance.

STORAGE

Store the tool in a dry, clean area out of reach of children.

During extended periods of storage, ensure that the tool is protected

against corrosion and rust.

At the end of the season, or if the tool is not being used for longer than

a month, wipe over all metal surfaces with an oil impregnated cloth to

protect them from corrosion or spray with a fine coat of oil.

TROUBLE SHOOTING

Problem Possible Cause Possible Solution

− Unit does not run − Extension cord not connected to

the plug

− Check extension cord is fully connected to tool

− Cord not connected to power

source

− Check extension cord is fully connected to a live receptacle

− Trigger switch not fully operated − Check that safety lock of button is fully depressed prior to

moving trigger

— Bar and chain running hot and

smoking

− Check chain tension for

over-tight condition

− Adjust chain tension

− Chain oil tank empty − Fill tank with chain oil

− Chain installed in wrong

direction

− Reverse chain so that cutters face the right direction

— Motor runs but chain is not rotating

− Chain tension too tight − Adjust chain tension

− Check guide bar and chain for

damage

− Replace damaged bar and chain with identical replacement

parts.

Use only new bar and chain oil or unused SAE 30 weight motor oil

may be substituted. Never use wasted oil, low quality oil, or

insufficient oil. This could damage the pump; the bar and the chain

which may result in serious personal injury.

13

Model CVPS43010

CALL US FIRST !!

Call us first with questions about operating or maintaining your product

at 1.800.313.5111 between 8:00 a.m. – 5:00 p.m. Eastern

Standard Time, or get assistance on www.americanlawnmower.com.

PARTS AND SERVICE

Always mention the model number when ordering kits/items for this tool.

For parts or service, please call 1-800-313-5111 or visit us online at

www.americanlawnmower.com. Be sure to provide all relevant information when you call or visit.

REPAIR PARTS (KITS/ ITEMS)

MODEL NUMBER CVPS43010_____

SERIAL NUMBER_______________

The model/ serial number of this tool is found on a plate or label attached to the housing. Please

record the serial number in the space provided below.

14

Model CVPS43010

No. Kit/Item Number Description QTY

1 CVPS43-OTC

Oil Tank Cap Assy

1

2 CVPS43-SCK Sprocket Cover Kit 1

3

CVPS43-PK-1 Pole Kit 1

4

CVPS43-THK-1 Trigger Handle Kit 1

NOTES

__________________________________________________________________

15

Model CVPS43010

In a continued commitment to improve quality, the Manufacturer reserves the right to

make component changes or design changes when necessary.

WARRANTY POLICY

Earthwise warrants to the original owner that each new product and service part is free from defects in

materials and workmanship and agrees to repair or replace any defective product or part for the warranty period

as stated above from the original date of purchase except for the conditions and circumstances listed below:

Products sold damaged or incomplete, sold “as is”, or sold as

reconditioned are not covered under the warranty.

Damage or liability caused by shipping, improper handling,

improper assembly, incorrect voltage, improper wiring, improper

maintenance, improper modification or the use of accessories

and/or attachments not specifically recommended is not covered

by this warranty.

Expendable items that become worn during normal use are not

covered by the warranty, including, but not limited to guide bar

and chain.

Warranty does not cover damage caused by cold, heat, rain,

excessive humidity, corrosive environments and materials, or

other contaminants.

Warranty does not include installation, assembly or normal

adjustments explained in the operator’s manual.

The expense of delivering the product to the vendor and the

expense of returning the product or replacement parts to the

owner is not covered by the warranty.

The warranty does not cover normal deterioration of the exterior

finish, including but not limited to scratches, dents, paint chips or

any corrosion or discoloration caused by heat, abrasive and

chemical cleaners.

This warranty applies only to the original purchaser at retail and

may not be transferred.

Warranty applies if the product is used for personal, household

or family use. Warranty is void if product is used for commercial,

industrial or rental purposes.

Warranty does not include repairs necessary due to operator’s

abuse or negligence (including overloading the product beyond

capacity or immersion in water), or the failure to assemble,

operate, maintain or store the product according to the

instructions in the operator’s manual.

This warranty is not transferable and

only applies to product sold directly

from an authorized retailer. This warranty

does not apply to any product, new or used, purchased through

unauthorized third-party channels.

ANY INCIDENTAL, INDIRECT OR CONSEQUENTIAL LOSS,

DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY

DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCT IS

NOT COVERED BY THE WARRANTY. Some states do not

allow the exclusion or limitation on how long an implied warranty

lasts, so the above limitation may not apply to you.

Rev. 11/13/2018

OWNER’S MANUAL

CVPS43010 ELECTRIC CONVERTIBLE 2 IN 1 COMBO

CHAIN SAW/ POLE SAW

Two (2) year limited warranty on Earthwise outdoor equipment.

Proof of purchase, original dated sales receipt, must accompany all

warranty claims.

American Lawn Mower Company

The Great States Corporation

7444 Shadeland Station Way

Indianapolis, IN 46256 USA

Phone 1-800-313-5111

www.americanlawnmower.com

MANUAL DEL PROPIETARIO

ELÉCTRICA CONVERTIBLE COMBINADA 2 EN 1

MOTOSIERRA /MOTOSIERRA TELESCÓPICO

GUARDE ESTE MANUAL PARA CONSULTAS FUTURAS

Modelo CVPS43010

Su cortasetos fue diseñado y fabricado de acuerdo con nuestros altos estándares de confiabilidad, facilidad de

operación y seguridad para el operario. Si se lo trata con cuidado, le otorgará años de óptimo rendimiento y resistencia.

ADVERTENCIA: Para reducir el riesgo de sufrir alguna lesión, el usuario debe leer y comprender el

manual del propietario antes de usar este producto.

Muchas gracias por su compra.

NO DEVUELVA ESTE PRODUCTO A LA TIENDA. ¿TIENE PREGUNTAS SOBRE FUNCIONAMIENTO,

MONTAJE, PIEZAS O SERVICIO TÉCNICO? IR A WWW.AMERICANLAWNMOWER.COM O LLAME AL 1

-800-313-5111 ENTRE LAS 8:00 AM Y LAS 5:00 PM, HORA DEL ESTE DE LOS ESTADOS UNIDOS.

ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTAS ELÉCTRICAS

2

Modelo CVPS43010

ADVERTENCIAS DE SEGURIDAD IMPORTANTES

ADVERTENCIA: Lea todas las advertencias de seguridad y las

instrucciones. La inobservancia de las advertencias e instrucciones

puede causar descargas eléctricas, incendios o lesiones graves.

Guarde todas las advertencias e instrucciones para consultarlas

en el futuro. El término “herramienta eléctrica” en las advertencias se

refiere a las herramientas eléctricas que funcionan con corriente (con

cordón) o las que funcionan con batería (inalámbricas).

Área de trabajo

• Mantenga limpia y bien iluminada el área de trabajo. Un área

de trabajo mal despejada o mal iluminada propicia accidentes.

• No utilice herramientas motorizadas en atmósferas

explosivas, como las existentes alrededor de líquidos, gases

y polvos inflamables. Las herramientas eléctricas generan

chispas que pueden encender el polvo y los vapores inflamables.

• Mantenga alejados a los niños y circunstantes al maniobrar

una herramienta eléctrica. Toda distracción puede causar la

pérdida del control de la herramienta.

Seguridad eléctrica

• Las clavijas de las herramientas eléctricas deben

corresponder a las tomas de corriente donde se conectan.

Nunca modifique la clavija de ninguna forma. No utilice

ninguna clavija adaptadora con herramientas eléctricas

dotadas de contacto a tierra. Conectando las clavijas originales

en las tomas de corriente donde corresponden se disminuye el

riesgo de una descarga eléctrica.

• Evite el contacto del cuerpo con las superficies de objetos

conectados a tierra, como las tuberías, radiadores, estufas y

refrigeradores. Existe un mayor riesgo de descargas eléctricas

si el cuerpo está haciendo tierra.

• No exponga las herramientas eléctricas a la lluvia ni a

condiciones de humedad. La introducción de agua en una

herramienta eléctrica aumenta el riesgo de descargas eléctricas.

• No maltrate el cordón eléctrico. Nunca utilice el cordón para

trasladar, desconectar o tirar de la herramienta eléctrica.

Mantenga el cordón lejos del calor, aceite, bordes afilados y

piezas móviles. Los cordones eléctricos dañados o enredados

aumentan el riesgo de descargas eléctricas.

• Al utilizar una herramienta eléctrica a la intemperie, use un

cordón de extensión apropiado para el exterior. Usando un

cordón adecuado para el exterior se disminuye el riesgo de

descargas eléctricas.

• Si debe operar una herramienta en lugares húmedos, use un

suministro protegido por un interruptor de circuito con pé-

rdida a tierra (GFCI). El uso de un GFCI reduce el riesgo de

descargas eléctricas.

Seguridad personal

• Permanezca alerta, preste atención a lo que esté haciendo y

aplique el sentido común al utilizar herramientas

eléctricas. No utilice la herramienta eléctrica si está

cansado o se encuentra bajo los efectos de alguna droga,

alcohol o medicamento. Un momento de inatención al utilizar

una herramienta eléctrica puede causar lesiones corporales

serias.

• Utilice protección el equipo otros. Siempre póngase

protección ocular. El uso de equipo protector como mascarilla

para el polvo, calzado de seguridad, casco y protección para los

oídos en las circunstancias donde corresponda disminuye el

riesgo de lesiones.

• Evite que la herramienta se active accidentalmente.

Asegúrese de que el interruptor esté en la posición de

apagado antes de conectar la herramienta a un suministro

de corriente o de colocar un paquete de baterías.

Transportar herramientas eléctricas con el dedo en el

interruptor o enchufar herramientas eléctricas que tienen el

interruptor encendido puede ocasionar accidentes.

• Retire toda llave o herramienta de ajuste antes de encender

la herramienta eléctrica. Toda llave o herramienta de ajuste

dejada en una pieza giratoria de la herramienta eléctrica puede

causar lesiones.

• No estire el cuerpo para alcanzar mayor distancia.

Mantenga una postura firme y buen equilibrio en todo

momento. De esta manera se logra un mejor control de la

herramienta eléctrica en situaciones inesperadas.

• Vístase adecuadamente. No vista ropas holgadas ni joyas.

Mantenga el cabello, la ropa y los guantes alejados de las

piezas móviles. Las ropas holgadas y las joyas, así como el

cabello largo, pueden engancharse en las piezas móviles.

• Si se suministran dispositivos para conectar mangueras de

extracción y captación de polvo, asegúrese de que éstas

estén bien conectadas y se usen correctamente. El uso de la

captación de polvo puede reducir los peligros relacionados con

éste.

Empleo y cuidado de la herramienta eléctrica

• No fuerce la herramienta eléctrica. Utilice la herramienta

eléctrica adecuada para cada trabajo. La herramienta eléctrica

adecuada efectúa mejor y de manera más segura el trabajo, si

además se maneja a la velocidad para la que está diseñada.

• No utilice la herramienta si el interruptor no enciende o no

apaga. Cualquier herramienta eléctrica que no pueda

controlarse con el interruptor es peligrosa y debe repararse.

• Desconecte la clavija del suministro de corriente o retire el

paquete de baterías de la herramienta eléctrica, según sea

el caso, antes de efectuarle cualquier ajuste, cambiarle

accesorios o guardarla. Tales medidas preventivas de

seguridad reducen el riesgo de poner en marcha

accidentalmente la herramienta.

• Guarde las herramientas eléctricas desocupadas fuera del

alcance de los niños y no permita que las utilicen personas

no familiarizadas con las mismas o con estas instrucciones.

Las herramientas eléctricas son peligrosas en manos de

personas no capacitadas en el uso de las mismas.

• Preste servicio a las herramientas eléctricas. Revise para

ver si hay desalineación o atoramiento de piezas móviles,

ruptura de piezas o cualquier otra condición que pueda

afectar el funcionamiento de la herramienta. Si está dañada

la herramienta eléctrica, permita que la reparen antes de

usarla. Numerosos accidentes son causados por herramientas

eléctricas mal cuidadas.

• Mantenga las herramientas de corte afiladas y limpias. Las

herramientas de corte bien cuidadas y con bordes bien afilados,

tienen menos probabilidad de atascarse en la pieza de trabajo y

son más fáciles de controlar.

• Utilice la herramienta eléctrica, los accesorios y brocas, hojas

y cuchillas de corte, ruedas de esmeril, etc. de conformidad

con estas instrucciones, tomando en cuenta las condiciones

de trabajo y la tarea por realizar. Si se utiliza la herramienta

eléctrica para operaciones diferentes de las indicadas podría

originar una situación peligrosa.

Servicio

• Permita que un técnico de reparación calificado preste

ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTAS ELÉCTRICAS

servicio a la herramienta eléctrica, y sólo con piezas de

repuesto idénticas. De esta manera se mantiene la seguridad

de la herramienta eléctrica.

• Al dar servicio a una herramienta eléctrica, sólo utilice

piezas de repuesto idénticas. Siga las instrucciones

señaladas en la sección Mantenimiento de este manual. El

empleo de piezas no autorizadas o el incumplimiento de las

instrucciones de mantenimiento puede significar un riesgo de

descarga eléctrica o de lesiones.

ADVERTENCIAS DE SEGURIDAD DE LA MOTOSIERRA

• Mantenga todas las partes del cuerpo alejadas de la

motosierra mientras esté en funcionamiento. Antes de en-

cender la motosierra, asegúrese de que no esté en

contacto con nada. Un momento de distracción mientras usa la

motosierra puede hacer que la motosierra agarre su ropa o una

parte de su cuerpo.

• Siempre sostenga la motosierra con la mano derecha en el

mango trasero y la mano izquierda en el mango delantero.

Sostener la motosierra con las manos invertidas aumenta el riesgo

de sufrir lesiones personales y siempre debe evitarse.

• Sostenga la herramienta eléctrica únicamente por las partes

aisladas, porque la misma podría morder cables ocultos. Si la

motosierra toca un cable vivo, las piezas metálicas de la

herramienta podrían energizarse y producirle una descarga eléctri-

ca al operador.

• Use gafas de seguridad y protección auditiva. También se

recomienda usar equipo de protección para la cabeza, las

manos, las piernas y los pies. La indumentaria de protección

adecuada reducirá las lesiones personales en caso de que salgan

partículas despedidas o su cuerpo toque accidentalmente la

motosierra.

• No use la motosierra sobre un árbol. Si usa la motosierra su-

bido a un árbol, podría sufrir lesiones personales.

• Siempre mantenga un buen apoyo y utilice la motosierra

únicamente sobre superficies fijas, firmes y niveladas. Las

superficies resbaladizas o inestables como las escaleras pueden

hacerle perder el equilibrio o el control de la motosierra.

• Cuando corte una rama que esté sometida a tensión, esté

atento al retorno. Cuando se libera la tensión de las fibras de

madera, la rama podría golpear al operador o lanzar la motosierra

en forma descontrolada.

• Tenga extremo cuidado al cortar maleza o retoños. El material

delgado podría quedar atrapado en la motosierra y salir disparado

hacia usted o hacerle perder el equilibrio.

• Transporte la motosierra apagada, lejos de su cuerpo y toma-

da del mango frontal. Siempre que transporte o alma-

cene la motosierra, coloque la cubierta de la barra guía. Ma-

nipular la motosierra correctamente reduce la probabilidad de

tocar accidentalmente la cadena en movimiento.

• Siga las instrucciones para lubricar la herramienta,

tensionar la cadena y cambiar los accesorios. Si la cadena no

está correctamente tensionada o lubricada, podría romperse o

presentar un mayor riesgo de que ocurra un contragolpe.

• Mantenga los mangos secos, limpios y sin aceite ni grasa. Los

mangos con aceite o grasa son resbaladizos y pueden hacerle

perder el control.

• Corte únicamente madera. No use la motosierra para usos

distintos de los previstos. Por ejemplo: no use la

motosierra para cortar plástico, mampostería ni materiales

de construcción que no sean de madera. El uso de la

motosierra para fines distintos de los previstos podría dar lugar a

una situación de riesgo.

Causas y prevención del contragolpe:

Puede ocurrir un contragolpe cuando la punta de la barra guía

toca un objeto o cuando la madera se cierra y pellizca la

cadena de la sierra en el punto de corte.

En algunos casos, el contacto de la pieza de trabajo con la pun-

ta de la barra guía puede causar una reacción súbita en direc-

ción inversa, la cual lanza la barra guía hacia arriba y hacia

atrás, en dirección al operador.

El pellizcamiento de la cadena de la sierra en la parte superior

de la barra guía puede empujar la barra rápidamente hacia

atrás, en dirección al operador.

Cualquiera de estas dos reacciones puede causar la pérdida del

control de la sierra, lo cual a su vez puede producir

lesiones personales serias. No dependa exclusivamente de los

dispositivos de seguridad incorporados de la sierra. Como usu-

ario de una motosierra, debe tomar varias medidas para evitar

los accidentes y las lesiones en todos sus trabajos de corte.

El contragolpe es el resultado de un uso indebido de la

herramienta o de procedimientos o condiciones de utilización

incorrectos, y se puede evitar tomando las precauciones

apropiadas que se presentan a continuación:

• Mantenga la herramienta bien sujeta, con los pulgares y los

dedos alrededor de los mangos de la motosierra; sostenga

la herramienta con ambas manos y posicione su cuerpo y

su brazo de una forma que le permita resistir la fuerza de un

contragolpe. El operador puede controlar las fuerzas del

contragolpe si toma las precauciones adecuadas. No suelte la

motosierra.

• No se estire ni corte por encima de la altura del hombro.

Esto ayuda a evitar el contacto accidental con la punta y

permite un mejor control de la motosierra ante situaciones

inesperadas.

• Use únicamente barras y cadenas de repuesto indicadas

por el fabricante. El uso de barras y cadenas de repuesto

incorrectas podría hacer que la cadena se rompa o que se

produzcan contragolpes.

• Siga las instrucciones de afilado y mantenimiento de la

cadena de la sierra que provee el fabricante. Disminuir la

altura del calibrador de profundidad puede aumentar la

probabilidad de que ocurra un contragolpe.

3

Modelo CVPS43010

CABLE DE EXTENSIÓN. Asegúrese de que el cable de

extensión esté en buenas condiciones. Además, compruebe

que tenga el grosor suficiente para transportar la corriente que

necesitará el producto. Un cable de extensión muy pequeño

provocará una disminución en la tensión de la línea y, como

resultado, una pérdida de potencia y recalentamiento. La

siguiente tabla muestra el tamaño correcto que se debe usar

según la longitud del cable y el amperaje de la etiqueta. Ante la

duda, utilice el siguiente calibre más grueso. Cuanto más bajo

es el número de calibre, más grueso es el cable.

ADVERTENCIA: Utilice los cables de extensión de la puerta

rotulados SW-A, SOW-A, STW-A, SJW-A o SJTW-A. Estos

cables están especificados para usarse al aire libre y reducir el

riesgo de descarga eléctrica.

DOBLE AISLAMIENTO. El doble aislamiento es un concepto

de seguridad en las herramientas eléctricas que elimina la

necesidad del acostumbrado cable de alimentación puesto a

tierra mediante el sistema de tres cables. Todas las piezas

metálicas expuestas están separadas de los componentes

metálicos internos del motor por un aislamiento protector.

Las herramientas con doble aislamiento no necesitan la

conexión a tierra.

NOTA: La finalidad del sistema de doble aislamiento es

proteger al usuario de una descarga eléctrica provocada por

una rotura del aislamiento interno de la herramienta. Respete

todas las precauciones generales de seguridad para evitar

una descarga eléctrica.

El cable de extensión y el cable de alimentación

se pueden atar para evitar que se desconecten

durante el uso. Realice el nudo como se muestra

en la imagen y, después, conecte el enchufe del

cable de alimentación en el receptáculo del

cable de extensión. Este método también se puede aplicar

para unir dos cables de extensión.

ENCHUFES POLARIZADOS. Para reducir el riesgo de

una descarga eléctrica, este equipo tiene un enchufe

polarizado (un contacto es más ancho que el otro). Se

debe utilizar un cable de extensión polarizado adecuado

de dos o tres cables. Las conexiones polarizadas encajan

de una sola manera. Asegúrese de que el extremo del

receptáculo del cable de extensión tenga ranuras de

anchos diferentes para los contactos. Invierta el enchufe si

no encaja exactamente en el cable de extensión. Si aun

así no encaja, consiga un cable de extensión adecuado. Si

el cable de extensión no se adapta bien al tomacorriente,

llame a un electricista competente para que instale un

tomacorriente adecuado. No modifique el enchufe de la

herramienta ni el cable de extensión de ningún modo.

VERIFIQUE LAS PIEZAS DAÑADAS. Antes de seguir

usando el cortasetos, se deberán revisar los protectores u

otras piezas dañadas en forma exhaustiva para determinar

si la herramienta funcionará correctamente y realizará el

trabajo previsto. Verifique la alineación y las uniones de las

piezas móviles, el montaje, las averías y otros factores que

puedan afectar el funcionamiento. Un protector o cualquier

otra pieza dañada deben ser reemplazados o reparados

en forma adecuada. Comuníquese con nuestra línea de

ayuda de atención al cliente al 1-800-313-5111 para recibir

asistencia.

ADVERTENCIA: Disposición 65 del estado de California:

Este producto contiene químicos reconocidos por el estado

de California como causantes de cáncer, defectos de

nacimiento u otros efectos nocivos para el aparato

reproductor.

ADVERTENCIA: Parte del polvo y los residuos generados

por esta herramienta podría contener químicos

reconocidos por el estado de California como causantes

de cáncer, defectos de nacimiento u otros efectos nocivos

para el aparato reproductor. Algunos ejemplos de estos

productos químicos son:

-químicos presentes en fertilizantes;

-compuestos en insecticidas, herbicidas y pesticidas;

-arsénico y cromo de maderas tratadas químicamente.

El riesgo que usted corre al exponerse a estos químicos

varía según la frecuencia con la que realiza este tipo de

trabajo. Para reducir la exposición, trabaje en una zona

bien ventilada y utilice equipo de protección aprobado,

como mascarillas antipolvo especialmente diseñadas para

filtrar partículas microscópicas.

ADVERTENCIA: Cáncer y Daño Reproductivo -

www.P65Warnings.ca.gov.

PRECAUCIÓN: Nunca se pare bajo la rama que está

cortando. Ubíquese fuera del alcance de desechos que

puedan caer.

Calibre mínimo para los cables

Voltios Longitud total del cable en metros (pies)

120V 0-7,6 7,9-15,2 15,5-30,4 30,7-45,7

(0-25) (26-50) (51-100) (101-150)

Amperaje

Más No

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 No se recomienda

4

Modelo CVPS43010

La page charge ...

EarthWise CVPS43010 Le manuel du propriétaire

EarthWise CVPS43010 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents