Pioneer PAC 420 2TB B Manuel utilisateur

Operating Instructions

Mode d’emploi

Инструкции по эксплуатации

Discover the benefits of registering your product online at

http://www.pioneer.co.uk

(or http://www.pioneer.eu).

Découvrez les nombreux avantages offerts en enregistrant votre produit en ligne

maintenant sur

http://www.pioneer.fr

(ou http://www.pioneer.eu).

Зарегистрируйте Baшe изделие на

http://www.pioneer-rus.ru

(или

http://www.pioneer.eu). Oзнакомьтесь с преимуществами регистрации в Интернет

VSX-420

-S/-K

VSX-420_SY_En.book 1 ページ２０１０年３月１９日　金曜日　午前９時３７分

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 60 cm at top, 10 cm at rear, and 30 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

D3-4-2-1-2-2*_A1_En

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified

service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug. Should

the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to

BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug

must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of

safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows;

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

VSX-420_SY_En.book 2 ページ２０１０年３月１９日　金曜日　午前９時３７分

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Pb

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left unused

for a long period of time (for example, when on

vacation).

D3-4-2-2-1a_A1_En

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic”, and the

double-D symbol are trademarks of Dolby

Laboratories.

Manufactured under license under U.S.

Patent #’s: 5,451,942; 5,956,674; 5,974,380;

5,978,762; 6,226,616; 6,487,535 & other U.S.

and worldwide patents issued & pending.

DTS and the Symbol are registered

trademarks & DTS Digital Surround, the DTS

96/24 and the DTS logos are trademarks of

DTS, Inc. Product includes software. © DTS,

VSX-420_SY_En.book 3 ページ２０１０年３月１９日　金曜日　午前９時３７分

4

En

Thank you for buying this Pioneer product. Please read through these operating instructions so you

will know how to operate your model properly. After you have finished reading the instructions, put

them away in a safe place for future reference.

Contents

Flow of settings on the receiver . . 5

01 Before you start

Checking what’s in the box . . . . . . . . . . . . . . . 6

Loading the batteries . . . . . . . . . . . . . . . . . . . 6

Installing the receiver . . . . . . . . . . . . . . . . . . . 6

Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . 6

02 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operating range of remote control unit . . . . 8

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Remote control . . . . . . . . . . . . . . . . . . . . . . . 10

03 Connecting your equipment

Placing the speakers. . . . . . . . . . . . . . . . . . . 13

Hints on the speaker placement. . . . . . . . . 13

Connecting the speakers . . . . . . . . . . . . . . . 14

Making cable connections . . . . . . . . . . . . . . 15

HDMI cables . . . . . . . . . . . . . . . . . . . . . . . 15

About HDMI . . . . . . . . . . . . . . . . . . . . . . . . 15

Analog audio cables. . . . . . . . . . . . . . . . . . 15

Digital audio cables . . . . . . . . . . . . . . . . . . 16

Video cables . . . . . . . . . . . . . . . . . . . . . . . . 16

About video outputs connection . . . . . . . . . . 16

Connecting a TV and Blu-ray Disc player. . . . 17

Connecting a TV and DVD player . . . . . . . . . 18

Connecting using HDMI. . . . . . . . . . . . . . . 18

Connecting your component with no

HDMI terminal . . . . . . . . . . . . . . . . . . . . . . 19

Connecting an HDD/DVD recorder, VCR

and other video components. . . . . . . . . . . . . 20

Connecting a satellite receiver or other

digital set-top box . . . . . . . . . . . . . . . . . . . . . 21

Connecting the multichannel analog

outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connecting other audio components . . . . . . 22

Connecting to the front panel audio

mini jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Connecting antennas . . . . . . . . . . . . . . . . . . 23

Using external antennas. . . . . . . . . . . . . . . 23

Connecting an IR receiver. . . . . . . . . . . . . . . 24

Plugging in the receiver . . . . . . . . . . . . . . . . 24

04 Listening to your system

Basic playback . . . . . . . . . . . . . . . . . . . . . . . 25

Choosing the input signal. . . . . . . . . . . . . . 26

Auto playback . . . . . . . . . . . . . . . . . . . . . . . . 26

Listening in surround sound . . . . . . . . . . . . . 26

Using the Advanced surround effects . . . . 27

Listening in stereo. . . . . . . . . . . . . . . . . . . . . 27

Using Front Stage Surround Advance . . . . . . 28

Using Stream Direct . . . . . . . . . . . . . . . . . . . 28

Using the Sound Retriever. . . . . . . . . . . . . . . 28

Using Phase Control . . . . . . . . . . . . . . . . . . . 29

Setting the Audio options . . . . . . . . . . . . . . . 30

Selecting the multichannel analog inputs . . . 32

Using the headphone . . . . . . . . . . . . . . . . . . 32

05 The System Setup menu

Using the System Setup menu . . . . . . . . . . . 33

Manual speaker setup. . . . . . . . . . . . . . . . . . 33

Speaker setting. . . . . . . . . . . . . . . . . . . . . . 33

Crossover network . . . . . . . . . . . . . . . . . . . 34

Channel level . . . . . . . . . . . . . . . . . . . . . . . 34

Speaker Distance . . . . . . . . . . . . . . . . . . . . 35

The Input Assign menu . . . . . . . . . . . . . . . . . 35

06 Using the MULTI-ZONE feature

MULTI-ZONE listening . . . . . . . . . . . . . . . . . . 36

Making MULTI-ZONE connections . . . . . . . 36

Using the MULTI-ZONE controls . . . . . . . . . 37

07 Using the tuner

Listening to the radio. . . . . . . . . . . . . . . . . . . 38

Improving FM sound. . . . . . . . . . . . . . . . . . 38

Saving station presets . . . . . . . . . . . . . . . . . . 38

Listening to station presets. . . . . . . . . . . . . 39

Naming preset stations. . . . . . . . . . . . . . . . 39

An introduction to RDS . . . . . . . . . . . . . . . . . 39

Searching for RDS programs . . . . . . . . . . . 40

Displaying RDS information . . . . . . . . . . . . 40

08 Making recordings

Making an audio or a video recording . . . . . . 41

09 Additional information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 42

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Resetting the main unit. . . . . . . . . . . . . . . . . 44

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 45

Cleaning the unit. . . . . . . . . . . . . . . . . . . . . . 45

VSX-420_SY_En.book 4 ページ２０１０年３月１９日　金曜日　午前９時３７分

5

En

English

Français

Italiano

Español

Nederlands

Deutsch

Flow of settings on the receiver

The unit is a full-fledged AV receiver equipped

with an abundance of functions and terminals.

It can be used easily after following the

procedure below to make the connections and

settings.

The colors of the steps indicate the following:

Required setting item

Setting to be made as necessary

1

Before you start

• Checking what’s in the box (page 6)

• Loading the batteries (page 6)



2

Connecting the speakers

Where you place the speakers will have a big

effect on the sound. Place your speakers as

shown below for the best surround sound effect.

• Placing the speakers (page 13)

• Connecting the speakers (page 14)



3

Connecting the components

For surround sound, you’ll want to hook up

using a digital connection from the BD/DVD

player to the receiver.

• About video outputs connection (page 16)

• Connecting a TV and Blu-ray Disc player

(page 17)

• Connecting a TV and DVD player (page 18)

• Connecting antennas (page 23)

• Plugging in the receiver (page 24)



Front

Left (L)

Surround

Left (SL)

Surround

Right (SR)

Center (C)

Subwoofer (SW)

Listening

position

Front

Right (R)



4

Power On

Make sure you’ve set the video input on your TV to

this receiver. Check the manual that came with

the TV if you don’t know how to do this.



5

The Input Assign menu (page 35)

(When using connections other than the

recommended connections.)



6

Playback

• Basic playback (page 25)

• Choosing the input signal (page 26)



7

Adjusting the sound as desired

•Using the various listening modes

• Using the Sound Retriever (page 28)

• Using Phase Control (page 29)

• Setting the Audio options (page 30)

• Manual speaker setup (page 33)

VSX-420_SY_En.book 5 ページ２０１０年３月１９日　金曜日　午前９時３７分

Before you start01

6

En

Chapter 1:

Before you start

Checking what’s in the box

Please check that you’ve received the following

supplied accessories:

• Remote control

• AAA size IEC R03 dry cell batteries (to

confirm system operation) x2

•AM loop antenna

•FM wire antenna

•Power cord

• Warranty card

• These operating instructions

Loading the batteries

CAUTION

Incorrect use of batteries may result in such

hazards as leakage and bursting. Observe the

following precautions:

• Never use new and old batteries together.

• Insert the plus and minus sides of the

batteries properly according to the marks

in the battery case.

• Batteries with the same shape may have

different voltages. Do not use different

batteries together.

• When disposing of used batteries, please

comply with governmental regulations or

environmental public instruction’s rules

that apply in your country or area.

• Do not use or store batteries in direct

sunlight or other excessively hot place,

such as inside a car or near a heater. This

can cause batteries to leak, overheat,

explode or catch fire. It can also reduce the

life or performance of batteries.

Installing the receiver

• When installing this unit, make sure to put

it on a level and stable surface.

Don’t install it on the following places:

– on a color TV (the screen may distort)

– near a cassette deck (or close to a device

that gives off a magnetic field). This may

interfere with the sound.

– in direct sunlight

– in damp or wet areas

– in extremely hot or cold areas

– in places where there is vibration or other

movement

– in places that are very dusty

– in places that have hot fumes or oils (such

as a kitchen)

Ventilation

When installing this unit, make sure to leave

space around the unit for ventilation to improve

heat dispersal (at least 60 cm at the top). If

not enough space is provided between the

unit and walls or other equipment, heat will

build up inside, interfering with performance

and/or causing malfunctions.

Slot and openings in the cabinet are provided

for ventilation and to protect the equipment

from overheating. To prevent fire hazard, do

not place anything directly on top of the unit,

make sure the openings are never blocked or

covered with items (such as newspapers,

table-cloths and curtains), and do not operate

the equipment on thick carpet or a bed.

Receiver

60 cm

VSX-420_SY_En.book 6 ページ２０１０年３月１９日　金曜日　午前９時３７分

Controls and displays 02

7

En

English

Français

Italiano

Español

Nederlands

Deutsch

Chapter 2:

Controls and displays

Front panel

1

 STANDBY/ON

2

INPUT SELECTOR

dial

Selects an input source.

3 Tuner control buttons

BAND

Switches between AM, FM ST (stereo) and

FM MONO radio bands (page 38).

TUNE +/–

Used to find radio frequencies (page 38).

TUNER EDIT

Use with TUNE +/–, PRESET +/– and

ENTER to memorize and name stations for

recall (page 38, 39).

PRESET +/–

Use to select preset radio stations (page 38).

4 Character display

See Display on page 8.

5

MASTER VOLUME

dial

6

PHONES

jack

Use to connect headphones (page 32).

7 Listening mode buttons

AUTO SURROUND/STREAM DIRECT

Switches between Auto surround mode

(Auto playback on page 26) and Stream

Direct playback. Stream Direct playback

bypasses the tone controls for the most

accurate reproduction of a source

(page 28).

STEREO/A.L.C.

Switches between stereo playback, Auto

level control stereo mode (page 27) and

Front Stage Surround Advance modes

(page 28).

ADVANCED SURROUND

Switches between the various surround

modes (page 27).

BAND

PHONES

INPUT

SELECTOR

STANDBY/ON

PHASE

CONTROL

AUTO SURROUND/

STREAM DIRECT

STEREO/

A.L.C.

ADVANCED

SURROUND

STANDARD

SURROUND

MASTER

VOLUME

SPEAKERSCONTROL

MULTI-ZONE

ON/OFF

PORTABLE

TUNER EDIT ENTER

AUDIO/ VIDEO MULTI-CHANNEL RECEIVER VSX-420

TUNE TUNE

+

PRESET PRESET

+

1 23 54

6107 89

VSX-420_SY_En.book 7 ページ２０１０年３月１９日　金曜日　午前９時３７分

Controls and displays02

8

En

STANDARD SURROUND

Press for Standard decoding and to switch

between the various 2 Pro Logic II options

(page 26).

8 MULTI ZONE controls

If you’ve made MULTI-ZONE connections (see

MULTI-ZONE listening on page 36) use these

controls to control the sub zone from the main

zone (see Using the MULTI-ZONE controls on

page 37).

9

SPEAKERS

Use to change the speaker system on or off.

When the SP OFF is selected, no sound is

output from the speakers connected to this

receiver.

10

PORTABLE

audio input jack

Connect an auxiliary component using a stereo

mini-jack cable (page 22).

Operating range of remote control unit

The remote control may not work properly if:

• There are obstacles between the remote

control and the receiver’s remote sensor.

• Direct sunlight or fluorescent light is

shining onto the remote sensor.

• The receiver is located near a device that is

emitting infrared rays.

• The receiver is operated simultaneously

with another infrared remote control unit.

Display

1 PHASE

Lights when the Phase Control is switched on

(page 29).

2 AUTO

Lights when the Auto Surround feature is

switched on (see Auto playback on page 26).

3RDS

Lights when an RDS broadcast is received

(page 40)

4ST

Lights when a stereo FM broadcast is being

received in auto stereo mode.

5TUNE

Lights when a broadcast is being received.

30°

7 m

1 2 43 5 6 7 8 910

11 1312 14 15 1716

VSX-420_SY_En.book 8 ページ２０１０年３月１９日　金曜日　午前９時３７分

Controls and displays 02

9

En

English

Français

Italiano

Español

Nederlands

Deutsch

6ZONE

Lights when the MULTI-ZONE feature is active

(page 36).

7 Speaker indicator

Shows if the speaker system is on or not

(page 32).

SP

A means the speakers are switched on.

SP

 means the speakers are switched off and

sound is output from the headphone jack.

8 Sleep timer indicator

Lights when the receiver is in sleep mode

(page 10).

9 Tuner preset indicators

PRESET

Shows when a preset radio station is

registered or called.

MEM

Blinks when a radio station is registered.

10 PRESET information or input signal

indicator

Shows the preset number of the tuner or the

input signal type, etc.

11 DTS indicators

DTS

Lights when a source with DTS encoded

audio signals is detected.

96/24

Lights when a source with DTS 96/24

encoded audio signals is detected.

12 Character display

Displays various system information.

13 Dolby Digital indicators

2 D

Lights when a Dolby Digital encoded signal

is detected.

2PLll

Lights to indicate Pro Logic II decoding

(see Listening in surround sound on

page 26 for more on this).

14 ADV.S.

Lights when one of the Advanced Surround

modes has been selected (see Using the

Advanced surround effects on page 27 for

more on this).

15 SIGNAL SELECT indicators

DIGITAL

Lights when a digital audio signal is

selected.

Blinks when a digital audio signal is not

selected.

16 DIMMER indicator

Shows when the display is set to turn off as

the DIMMER setting.

17 DIR.

Lights when the DIRECT or PURE DIRECT

mode is switched on (page 28).

VSX-420_SY_En.book 9 ページ２０１０年３月１９日　金曜日　午前９時３７分

Controls and displays02

10

En

Remote control

As for operating other devices, the remote

control codes for the Pioneer products are

preset. The settings cannot be changed.

1

SLEEP

Press to change the amount of time before the

receiver switches into standby (30 min –

60 min – 90 min – Off). You can check the

remaining sleep time at any time by pressing

SLEEP once.

2

 RECEIVER

Switches the receiver between standby and on.

To switch ZONE 2 on/off, press and hold SHIFT

button, then press  RECEIVER button.

3

Switches the remote to control the receiver

(used to select the white commands above the

number buttons (TEST TONE, etc)). Also use

this button to set up surround sound (page 33)

or Audio parameters (page 30).

4 INPUT SELECT

Use to select the input source.

5 MULTI CONTROL buttons

Use to select the input source to this receiver.

This will enable you to control other

components with the remote control.

6

Receiver control

buttons

SIGNAL SEL

Press to select the audio input signal of the

component to play back (page 26).

MIDNIGHT

Switches to Midnight or Loudness

listening (page 30).

PHASE

Press to switch on/off Phase Control

(page 29).

S.RETRIEVER

Press to restore CD quality sound to

compressed audio sources (page 28).

BD DVD

INPUT SELECT

SOURCESLEEP

TV

CONTROL

DIMMER

DVR

INPUT

1

4

7

TEST TONE

HDD

CH

RECEIVER

MULTI IN

CD

CD-R

PORTABLE

TUNER

SIGNAL SEL

MIDNIGHT PHASE

S.RETRIEVER

BD MENU

ENTER

STANDARD

ADV SURR

STEREO/

A.L.C.

AUTO/

DIRECT

VOL

+

10

2

5

8

SPEAKERS

LEV

SB CH

DISP

CLR

DVD

3

6

9

0

ENTER

CH

CH SELECT

VCR

SHIFT

MUTE

RETURN

AUDIO

PARAMETER

TUNER EDIT

TOOLS

MASTER

VOLUME

BAND

MENU

HOME

MENU

SETUP

TRE

BASS

TOP

MENU

RECEIVER

T

U

N

E

T

U

N

E

P

R

E

S

E

T

P

R

E

S

E

T

RECEIVER

DTV/TV

1

2

12

13

14

15

16

3

4

5

6

7

8

9

10

11

17

RECEIVER

VSX-420_SY_En.book 10 ページ２０１０年３月１９日　金曜日　午前９時３７分

Controls and displays 02

11

En

English

Français

Italiano

Español

Nederlands

Deutsch

7

Listening mode buttons

AUTO/DIRECT

Switches between Auto surround mode

(Auto playback on page 26) and Stream

Direct playback. Stream Direct playback

bypasses the tone controls for the most

accurate reproduction of a source

(page 28).

STEREO/A.L.C.

Switches between stereo playback, Auto

level control stereo mode (page 27) and

Front Stage Surround Advance modes

(page 28).

STANDARD

Press for Standard decoding and to switch

between 2 Pro Logic II options (page 26).

ADV SURR

Switches between the various surround

modes (page 27).

Press BD first to access:

BD MENU*

Displays the disc menu of Blu-ray Discs.

8

System Setup

and component control

buttons

The following button controls can be accessed

after you have selected the corresponding

MULTI CONTROL button (BD, TV, etc.).

Press first to access:

AUDIO PARAMETER

Use to access the Audio options (page 30).

SETUP

Press to access the System Setup menu

(page 33).

RETURN

Confirm and exit the current menu screen.

Press BD or DVR first to access:

TOP MENU

Displays the disc ‘top’ menu of a BD/DVD.

HOME MENU

Displays the HOME MENU screen.

RETURN

Confirm and exit the current menu

screen.

MENU

Displays the

disc menu of a DVD

.

Press TUNER first to access:

TUNER EDIT

Memorizes/names stations for recall

(page 38, 39).

HOME MENU

Use to search for RDS program types

(page 40).

BAND

Switches between AM, FM ST (stereo) and

FM MONO radio bands (page 38).

9



(

TUNE /

,

PRESET /

),

ENTER

Use the arrow buttons when setting up your

surround sound system (page 33). Also used

to control BD/DVD menus/options.

Use the TUNE / buttons can be used to

find radio frequencies (page 38) and the

PRESET / buttons can be used to select

preset radio stations (page 39).

10 Component control buttons

The main buttons (, , etc.) are used to

control a component after you have selected it

using the input source buttons.

The controls above these buttons can be

accessed after you have selected the

corresponding input source button (for

example BD, DVD, DVR or CD). These buttons

also function as described below.

RECEIVER

VSX-420_SY_En.book 11 ページ２０１０年３月１９日　金曜日　午前９時３７分

Controls and displays02

12

En

Press first to access:

BASS –/+

Use to adjust Bass

1

TRE –/+

Use to adjust Treble

1

11 Number buttons and other component

controls

2

Use the number buttons to directly select the

tracks on a CD, DVD, etc. There are other

buttons that can be accessed after the

button is pressed. (For example

TEST TONE, etc.)

HDD*, DVD*, VCR*

These buttons switch between the hard

disk, DVD and VCR controls for HDD/DVD/

VCR recorders.

TEST TONE

Outputs the test tones on each channel.

Use the / buttons to select the channel

and use the / buttons to adjust the

level on each channel. Pressing TEST

TONE again exits the test tone mode.

CH SELECT

Press repeatedly to select a channel, then

use LEV +/– to adjust the level (page 34).

LEV +/–

Use to adjust the channel levels.

SPEAKERS

Use to change the speaker system on or

off. When the SP OFF is selected, no sound

is output from the speakers connected to

this receiver.

DIMMER

Dims or brightens the display. The

brightness can be controlled in four steps.

12

 SOURCE

Turns on or off the power of the Pioneer DVD/

DVR units when BD, DVD or DVR is selected

using the MULTI CONTROL buttons.

13 TV CONTROL buttons

These buttons can control only be used with

Pioneer TVs.



Use to turn on/off the power of the TV.

INPUT

Use to select the TV input signal.

CH +/–

Use to select channels.

VOL +/–

Use to adjust the volume on your TV.

DTV/TV*

Switches between the DTV and analog TV

input modes for Pioneer TVs.

14

MASTER VOLUME

+/–

Use to set the listening volume.

15

MUTE

Mutes/unmutes the sound.

16

DISP

Switches the display of this unit. The input

name, listening mode or sound volume can be

checked by selecting an input source.

17

SHIFT

Press to access the ‘boxed’ commands (above

the buttons) on the remote. These buttons are

marked with an asterisk (* ) in this section. This

button is also used for operating ZONE 2

(page 37).

Note

1 The tone controls are disabled when the listening mode is set to DIRECT or PURE DIRECT.

2 SB CH button is not used with this receiver.

RECEIVER

VSX-420_SY_En.book 12 ページ２０１０年３月１９日　金曜日　午前９時３７分

Connecting your equipment 03

13

En

English

Français

Italiano

Español

Nederlands

Deutsch

Chapter 3:

Connecting your equipment

Placing the speakers

By connecting the left and right front speakers

(L/R), the center speaker (C), the left and right

surround speakers (SL/SR), and the subwoofer

(SW), a 5.1 ch surround system can be

enjoyed.

To achieve the best possible surround sound,

install your speakers as shown below.

Hints on the speaker placement

Where you put your speakers in the room has a

big effect on the quality of the sound. The

following guidelines should help you to get the

best sound from your system.

• The subwoofer can be placed on the floor.

Ideally, the other speakers should be at

about ear-level when you’re listening to

them. Putting the speakers on the floor

(except the subwoofer), or mounting them

very high on a wall is not recommended.

• For the best stereo effect, place the front

speakers 2 m to 3 m apart, at equal

distance from the TV.

• If you’re going to place speakers around

your CRT TV, use shielded speakers or

place the speakers at a sufficient distance

from your CRT TV.

• If you’re using a center speaker, place the

front speakers at a wider angle. If not,

place them at a narrower angle.

• Place the center speaker above or below

the TV so that the sound of the center

channel is localized at the TV screen. Also,

make sure the center speaker does not

cross the line formed by the leading edge

of the front left and right speakers.

• It is best to angle the speakers towards the

listening position. The angle depends on

the size of the room. Use less of an angle

for bigger rooms.

• Surround speakers should be positioned

60 cm to 90 cm higher than your ears and

titled slight downward. Make sure the

speakers don’t face each other. For DVD-

Audio, the speakers should be more

directly behind the listener than for home

theater playback.

• Try not to place the surround speakers

farther away from the listening position

than the front and center speakers. Doing

so can weaken the surround sound effect.

CAUTION

• Make sure that all speakers are securely

installed. This not only improves sound

quality, but also reduces the risk of

damage or injury resulting from speakers

being knocked over or falling in the event of

external shocks such as earthquakes.

120

SL

L

SW

C

R

SR

VSX-420_SY_En.book 13 ページ２０１０年３月１９日　金曜日　午前９時３７分

Connecting your equipment03

14

En

Connecting the speakers

The receiver will work with just two stereo

speakers (the front speakers in the diagram)

but using at least three speakers is

recommended, and a complete setup is best

for surround sound.

Make sure you connect the speaker on the

right to the right (R) terminal and the speaker

on the left to the left (L) terminal. Also make

sure the positive and negative (+/–) terminals

on the receiver match those on the speakers.

If you’re not using a subwoofer, change the

front speaker setting (see Speaker setting on

page 33) to LARGE.

CAUTION

• These speaker terminals carry

HAZARDOUS LIVE voltage. To prevent

the risk of electric shock when connecting

or disconnecting the speaker cables,

disconnect the power cord before touching

any uninsulated parts.

• Make sure that all the bare speaker wire is

twisted together and inserted fully into the

speaker terminal. If any of the bare speaker

wire touches the back panel it may cause

the power to cut off as a safety measure.

Be sure to complete all connections before

connecting this unit to the AC power source.

Bare wire connections

Front speaker terminals:

1 Twist exposed wire strands together.

2 Loosen terminal and insert exposed wire.

3 Tighten terminal.

Center and surround speaker terminals:

1 Twist exposed wire strands together.

2 Push open the tabs and insert exposed wire.

3 Release the tabs.

123

10 mm

12 3

10 mm

AUDIO

ANTENNA

FM

L

R

SPEAKERS A

OUT

MONITOR

YP

B

P

R

FRONT

ZONE2 OUT

MONITOR OUT BD/TV IN DVD/SAT IN

RL

SURROUND CENTER

SUBWOOFER

PRE OUT

L R

T

OUT

IN

DVR/VCR VIDEO

L

R

IN

RL

AC IN

SPEAKERS A

SURROUND CENTER

RL

FRONT

RL

SUBWOOFER

PRE OUT

SW

L

C

R

SL

SR

Center speaker

Surround speakers

Front speakers

Powered subwoofer

VSX-420_SY_En.book 14 ページ２０１０年３月１９日　金曜日　午前９時３７分

Connecting your equipment 03

15

En

English

Français

Italiano

Español

Nederlands

Deutsch

Making cable connections

Make sure not to bend the cables over the top

of this unit (as shown in the illustration). If this

happens, the magnetic field produced by the

transformers in this unit may cause a

humming noise from the speakers.

Important

• Before making or changing any connections,

switch off the power and disconnect the power

cord from the AC outlet.

• Before unplugging the power cord, switch

the power into standby.

HDMI cables

The HDMI cables transfers uncompressed

digital video.

1

Be careful to connect the terminal in the

proper direction.

About HDMI

HDMI (High Definition Multimedia Interface)

was developed to provide the technologies of

High Bandwidth Digital Content Protection

(HDCP) as well as Digital Visual Interface (DVI)

in one specification. HDCP is used to protect

digital content transmitted and received by

DVI-compliant displays.

HDMI has the capability to support standard,

enhanced, or high-definition video plus

standard to multi-channel surround-sound

audio. HDMI features include uncompressed

digital video, a bandwidth of up to 2.2

gigabytes per second (with HDTV signals),

one connector (instead of several cables and

connectors), and communication between

the AV source and AV devices such as DTVs.

Even if you connect the playback components

with an HDMI cable, no sound will come out

of the speaker connected to this receiver. An

audio cable connection is also needed for

this.

HDMI, the HDMI Logo and High-Definition

Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing, LLC

in the United States and other countries.

Analog audio cables

Use stereo RCA phono cables to connect

analog audio components. These cables are

typically red and white, and you should

connect the red plugs to R (right) terminals

and white plugs to L (left) terminals.

Note

1 If the video signal does not appear on your TV, try adjusting the resolution settings on your component or display. Note that

some components (such as video game units) have resolutions that may not be displayed. In this case, use a (analog)

composite connection.

HDMI cable

Right (red)

Analog audio cables

Left (white)

VSX-420_SY_En.book 15 ページ２０１０年３月１９日　金曜日　午前９時３７分

Connecting your equipment03

16

En

Digital audio cables

Commercially available coaxial digital audio

cables or optical cables should be used to

connect digital components to this receiver.

1

This connection is required to listen to the

multi-channel digital sounds with this receiver.

Video cables

Standard RCA video cables

These cables are the most common type of

video connection and are used to connect to

the composite video terminals. The yellow

plugs distinguish them from cables for audio.

Component video cables

Use component video cables to get the best

possible color reproduction of your video

source. The color signal of the TV is divided into

the luminance (Y) signal and the color (P

B and

P

R) signals and then output. In this way,

interference between the signals is avoided.

About video outputs connection

This receiver is not loaded with a video

converter. When you use component video

cables or HDMI cables for connecting to the

input device, the same cables should be used

for connecting to the TV.

The signals input from the analog (composite

and component) video inputs of this unit will

not be output from the HDMI OUT.

Note

1 • When connecting optical cables, be careful when inserting the plug not to damage the shutter protecting the optical socket.

• When storing optical cable, coil loosely. The cable may be damaged if bent around sharp corners.

• You can also use a standard RCA video cable for coaxial digital connections.

Coaxial digital audio cable Optical cable

S

tandard RCA video cable

Green (Y)

Blue (P

B

)

Red (P

R

)

Component video cables

VIDEO IN

P

R

P

B

Y

COMPONENT VIDEO IN

HDMI IN

MONITOR OUT

P

R

P

B

Y

COMPONENT VIDEO MONITOR OUT

HDMI OUT

Terminal for connection with source device

Terminal for connection with TV monitor

Playback

component

TV

Video signals can be output.

VSX-420_SY_En.book 16 ページ２０１０年３月１９日　金曜日　午前９時３７分

Connecting your equipment 03

17

En

English

Français

Italiano

Español

Nederlands

Deutsch

Connecting a TV and Blu-ray Disc player

Connect a TV and Blu-ray Disc player to this receiver using a commercially available HDMI cable.

Important

1 Even if you connect the playback

components with an HDMI cable, no sound

will come out of the speaker connected to this

receiver. An audio cable connection is also

needed for this.

2

If the connection was made using a coaxial

cable, press

SIGNAL SEL

repeatedly to select

C1

(see page 26).

3 If you connected the TV (as shown above)

and there is still no sound, press DVD then

press

SIGNAL SEL

repeatedly to select O2 or A

(see page 26).

AUDIO

DIGITAL

COMPONENT VIDEO

BD/TV MULTI CH IN

HDMI

ANTENNA

FM

UNBAL

75

Ω

AM

LOOP

FRONT

L

R

L

R

CENTERSURROUND

COAXIAL

(CD)

IN 1

1

-

2

IN 2

(BD/TV)

IN 1

(DVD/SA

T

IN 2

OPTICAL

ASSIGNABLE

IR

ASSIGNABLE

1

-

2

ASSIGNABLE

OUT

MONIT

O

YP

B

P

R

IN

ZONE2 OUT

MONITOR OUT DVD/SAT IN

SUBWOOFER

PRE OUT

L R

DVR/VCR

OUT

IN

DVR/VCR VIDEO

L

R

OUT

BD/TV

IN

DVD/SAT

IN

OUT

IN IN

CD-R/TAPE CD

SUBWOOFER

IN

MONITOR OUT BD/TV IN

L

R

DVD/SAT

IN

BD/TV IN

L

R

OUT

(BD/TV)

IN 1

HDMI

(DVD/SAT)

IN 2

DIGITAL AUDIO OUT

OPTICAL

RL

ANALOG AUDIO OUT

DIGITAL AUDIO OUT

COAXIAL

OPTICAL

RL

ANALOG AUDIO OUT

HDMI OUT

HDMI IN

1

2

3

This connection is

required in order to listen

to the sound of the TV over

the receiver.

Without this connection,

you will NOT be able to

listen to the player with this

receiver.

Select one

HDMI/DVI-compatible TV

HDMI/DVI-compatible

Blu-ray Disc player

VSX-420_SY_En.book 17 ページ２０１０年３月１９日　金曜日　午前９時３７分

Connecting your equipment03

18

En

Connecting a TV and DVD player

Connecting using HDMI

If you have an HDMI or DVI (with HDCP) equipped DVD player, you can connect it to this receiver

using a commercially available HDMI cable.

Important

1 Even if you connect the playback

components with an HDMI cable, no sound

will come out of the speaker connected to this

receiver. An audio cable connection is also

needed for this.

2

If the connection was made using a coaxial

cable, press

SIGNAL SEL

repeatedly to select

C1

(see page 26).

3 If you connected the TV (as shown above)

and there is still no sound, press BD then press

SIGNAL SEL

repeatedly to select O1 or A (see

page 26).

AUDIO

DIGITAL

COMPONENT VIDEO

BD/TV MULTI CH IN

HDMI

ANTENNA

FM

UNBAL

75

Ω

AM

LOOP

FRONT

L

R

L

R

CENTERSURROUND

COAXIAL

(CD)

IN 1

1

-

2

IN 2

(BD/TV)

IN 1

(DVD/SA

T

IN 2

OPTICAL

ASSIGNABLE

IR

ASSIGNABLE

1

-

2

ASSIGNABLE

OUT

MONIT

O

YP

B

P

R

IN

ZONE2 OUT

MONITOR OUT DVD/SAT IN

SUBWOOFER

PRE OUT

L R

DVR/VCR

OUT

IN

DVR/VCR VIDEO

L

R

OUT

BD/TV

IN

DVD/SAT

IN

OUT

IN IN

CD-R/TAPE CD

SUBWOOFER

IN

MONITOR OUT BD/TV IN

L

R

DVD/SAT

IN

BD/TV IN

L

R

OUT

(BD/TV)

IN 1

HDMI

(DVD/SAT)

IN 2

DIGITAL AUDIO OUT

OPTICAL

RL

ANALOG AUDIO OUT

DIGITAL AUDIO OUT

COAXIAL

OPTICAL

RL

ANALOG AUDIO OUT

HDMI OUT

HDMI IN

1

2

3

This connection is

required in order to listen

to the sound of the TV over

the receiver.

Without this connection,

you will NOT be able to

listen to the player with this

receiver.

Select one

HDMI/DVI-compatible TV

HDMI/DVI-compatible

DVD player

VSX-420_SY_En.book 18 ページ２０１０年３月１９日　金曜日　午前９時３７分

Connecting your equipment 03

19

En

English

Français

Italiano

Español

Nederlands

Deutsch

Connecting your component with no HDMI terminal

This diagram shows connections of a TV and DVD player (or other playback component) with no

HDMI terminal to the receiver.

Important

1 If you use component video cables for

connecting to the DVD player, the same cables

should be used for connecting to the TV

2 If necessary, assign the component video

inputs to the input source you’ve connected.

This only needs to be done if you didn’t connect

according to the following defaults:

• COMPONENT VIDEO IN 1 – BD/TV

• COMPONENT VIDEO IN 2 – DVD/SAT

See The Input Assign menu on page 35.

3

If the connection was made using a coaxial

cable, press

SIGNAL SEL

repeatedly to select

C1

(see page 26).

4 If you connected the TV (as shown above)

and there is still no sound, press BD then press

SIGNAL SEL

repeatedly to select O1 or A (see

page 26).

AUDIO

DIGITAL

COMPONENT VIDEO

BD/TV MULTI CH IN

BD/TV IN

HDMI

ANTENNA

FM

UNBAL

75

Ω

AM

LOOP

FRONT

L

R

L

R

CENTERSURROUND

COAXIAL

(CD)

IN 1

1

-

2

IN 1

(DVD/SAT)

IN 2

OPTICAL

ASSIGNABLE

IR

ASSIGNABLE

1

-

2

ASSIGNABLE

OUT

YP

B

P

R

IN

ZONE2 OUT

MONITOR OUT BD/TV IN DVD/SAT IN

SUBWOOFER

PRE OUT

L R

DVR/VCR DVD/S AT

OUT

IN

DVR/VCR VIDEO

L

R

OUT

BD/TV

IN

DVD/SAT

IN

OUT

IN IN

IN

CD-R/TAPE CD

SUBWOOFER

IN

(BD/TV)

IN 1

(DVD/SAT)

IN 2

COMPONENT VIDEO

(BD/TV)

IN 1

1

-

2

ASSIGNABLE

OUT

MONITOR

YP

B

P

R

DIGITAL AUDIO OUT

OPTICAL

RL

ANALOG AUDIO OUT

DIGITAL AUDIO OUT

COAXIAL

OPTICAL

RL

ANALOG AUDIO OUT

VIDEO OUT

COMPONENT VIDEO OUT

P

R

YP

B

VIDEO IN

COMPONENT VIDEO IN

P

R

YP

B

1,2

3

4

Select one

DVD player, etc.

TV

This connection is

required in order to

listen to the sound of

the TV over the

receiver.

VSX-420_SY_En.book 19 ページ２０１０年３月１９日　金曜日　午前９時３７分

Connecting your equipment03

20

En

Connecting an HDD/DVD recorder, VCR and other video components

This receiver has audio/video inputs and outputs suitable for connecting analog or digital video

recorders, including HDD/DVD recorders and VCRs.

• Only the signals that are input to the VIDEO IN terminal can be output from the VIDEO OUT

terminal.

• Audio signals that are input through the digital terminal will not be output from the analog

terminal.

Important

•

If the connection was made using

an

optical cable

, press

SIGNAL SEL

repeatedly

to select

O2

(see page 26).

Note

• If the video components and TV also has an

HDMI or a component video jacks, you can

connect this too. See Connecting using

HDMI on page 18 or Connecting your

component with no HDMI terminal on

page 19 for more on this.

PLAY

RL

DIGITAL

AUDIO OUT

ANALOG AUDIO OUT

RL

ANALOG AUDIO IN

OPTICAL

VIDEO OUT

VIDEO IN

REC

AUDIO

DIGITAL

COMPONENT VIDEO

BD/TVD MULTI CH IN

BD/TV IN

HDMI

ANTENNA

AM

LOOP

FRONT

L

R

L

R

CENTERSURROUND

COAXIAL

(CD)

IN 1

1

-

2

(BD/TV)

IN 1

(DVD/SAT)

IN 2

OPTICAL

ASSIGNABLE

IR

ASSIGNABLE

1

-

2

ASSIGNABLE

OUT

MONITOR

YP

B

P

R

IN

ZONE2 OUT

MONITOR OUT BD/DVD IN DVD/SAT IN

SUBWOOFER

PRE OUT

L R

DVR/VCR

DVD/SAT

OUT

IN

DVR/VCR VIDEO

L

R

OUT

DVD/SAT

IN

BD/TV

IN

OUT

IN IN

IN

CD-R/TAPE CD

SUBWOOFER

IN

(BD/TV)

IN 1

IN 2

L

R

DIGITAL

OUT

IN

DVR/VCR

OUT

IN

DVR/VCR VIDEO

COAXIAL

OPTICAL

(CD)

IN 1

(DVD/SAT)

IN 2

DVR, VCR, LD player, etc.

Select one

VSX-420_SY_En.book 20 ページ２０１０年３月１９日　金曜日　午前９時３７分

La page charge ...

Pioneer PAC 420 2TB B Manuel utilisateur

Ce manuel convient également à

Pioneer PAC 420 2TB B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents