Pioneer VSX-1020-K Le manuel du propriétaire

audio/video multi-channel receiver

récepteur audiovisuel multicanal

VSX-1020_SYXCN.book 1 ページ２０１０年３月１２日　金曜日　午前９時１０分

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 40 cm at top, 10 cm at rear, and 20 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

D3-4-2-1-2-2*_A1_En

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified

service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug. Should

the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to

BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug

must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of

safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows;

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

VSX-1020_SYXCN.book 2 ページ２０１０年３月１２日　金曜日　午前９時１０分

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Pb

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left unused

for a long period of time (for example, when on

vacation).

D3-4-2-2-1a_A1_En

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

VSX-1020_SYXCN.book 3 ページ２０１０年３月１２日　金曜日　午前９時１０分

Thank you for buying this Pioneer product. Please read through these operating instructions so you

will know how to operate your model properly. After you have finished reading the instructions, put

them away in a safe place for future reference.

Contents

Flow of settings on the receiver

. . .7

01 Before you start

Checking what’s in the box

. . . . . . . . . . . . . . . . 8

Installing the receiver

. . . . . . . . . . . . . . . . . . . . 8

Loading the batteries

. . . . . . . . . . . . . . . . . . . . 8

02 Controls and displays

Front panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Display

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Remote control

. . . . . . . . . . . . . . . . . . . . . . . 13

Operating range of remote control unit

. . . . . 14

03 Connecting your equipment

Rear panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Determining the speakers’ application

. . . . . . 17

Other speaker connections

. . . . . . . . . . . . . 18

Placing the speakers

. . . . . . . . . . . . . . . . . . 19

Some tips for improving sound quality

. . . . . 19

Connecting the speakers

. . . . . . . . . . . . . . . . 20

Installing your speaker system

. . . . . . . . . . . . 21

Bi-amping your speakers

. . . . . . . . . . . . . . . 22

Bi-wiring your speakers

. . . . . . . . . . . . . . . . 22

Selecting the Speaker system

. . . . . . . . . . . . . 23

Front height setup

. . . . . . . . . . . . . . . . . . . . 23

Front wide setup

. . . . . . . . . . . . . . . . . . . . . 23

Speaker B setup

. . . . . . . . . . . . . . . . . . . . . 23

Bi-Amping setup

. . . . . . . . . . . . . . . . . . . . . 23

ZONE 2 setup

. . . . . . . . . . . . . . . . . . . . . . . 23

About the audio connection

. . . . . . . . . . . . . . 24

About the video converter

. . . . . . . . . . . . . . . . 24

Connecting your TV and playback

components

. . . . . . . . . . . . . . . . . . . . . . . . . . 25

Connecting using HDMI

. . . . . . . . . . . . . . . 25

Connecting your DVD player with no

HDMI output

. . . . . . . . . . . . . . . . . . . . . . . . 27

Connecting your TV with no HDMI input

. . . . 28

Connecting a satellite/cable receiver or

other set-top box

. . . . . . . . . . . . . . . . . . . . . . 29

Connecting a HDD/DVD recorder, VCR and

Other audio problems

. . . . . . . . . . . . . . . . 110

Video

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Settings

. . . . . . . . . . . . . . . . . . . . . . . . . . 113

Professional Calibration EQ graphical

output

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Display

. . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Remote control

. . . . . . . . . . . . . . . . . . . . . 115

HDMI

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

Important information regarding the HDMI

connection

. . . . . . . . . . . . . . . . . . . . . . . . 117

USB interface

. . . . . . . . . . . . . . . . . . . . . . 118

ADAPTER PORT

. . . . . . . . . . . . . . . . . . . . 119

Internet radio

. . . . . . . . . . . . . . . . . . . . . . 119

About iPod

. . . . . . . . . . . . . . . . . . . . . . . . . 121

Surround sound formats

. . . . . . . . . . . . . . . 121

Dolby

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

DTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Windows Media Audio 9 Professional

. . . . 121

Auto Surround, ALC and Stream Direct with

different input signal formats

. . . . . . . . . . . . 122

Preset code list

. . . . . . . . . . . . . . . . . . . . . . 123

Specifications

. . . . . . . . . . . . . . . . . . . . . . . 132

Cleaning the unit

. . . . . . . . . . . . . . . . . . . . . 133

VSX-1020_SYXCN.book 6 ページ２０１０年３月１２日　金曜日　午前９時１０分

7

En

English

Français

Deutsch

Nederlands

Italiano

Español

Flow of settings on the receiver

The unit is a full-fledged AV receiver equipped

with an abundance of functions and terminals.

It can be used easily after following the

procedure below to make the connections and

settings.

The colors of the steps indicate the following:

Required setting item

Setting to be made as necessary

1

Before you start

• Checking what’s in the box (page 8)

• Loading the batteries (page 8)



2

Determining the speakers’ application

(page 17)

• 9.1 channel surround system (Front height)

• 9.1 channel surround system (Front wide)

• 7.1 channel surround system & Speaker B

connection

• 5.1 channel surround system & Front Bi-

amping connection (High quality surround)

• 5.1 channel surround system & ZONE 2

connection (Multi Zone)

• Some tips for improving sound quality (page

19)



3

Connecting the speakers

• Connecting the speakers (page 20)

• Installing your speaker system (page 21)

• Bi-amping your speakers (page 22)



4

Connecting the components

• About the audio connection (page 24)

• About the video converter (page 24)

• Connecting your TV and playback

components (page 25)

• Connecting AM/FM antennas (page 31)

• Plugging in the receiver (page 38)



5

Power On



6

Changing the OSD display language

(OSD Language) (page 39)



7

MCACC speaker settings

• Automatically conducting optimum sound

tuning (Auto MCACC) (page 39)



8

The Input Setup menu (page 42)

(When using connections other than the

recommended connections)



9

Basic playback (page 44)



10

Adjusting the sound and picture

quality as desired

•Using the various listening modes

• Better sound using Phase Control (page 62)

• Measuring the all EQ type (SYMMETRY/ALL

CH ADJ/FRONT ALIGN) (page 87)

• Changing the channel level while listening

(Tip on page 103)

• Switching on/off the Acoustic Calibration

EQ, Sound retriever or Dialog Enhancement

(page 68)

• Setting the PQLS function (page 66)

• Setting the Audio options (Tone, Loudness

or Sound delay, etc.) (page 68)

• Setting the Video options (page 71)



11

Other optional adjustments and

settings

• HDMI Setup (page 64)

• The Advanced MCACC menu (page 86)

• The System Setup and Other Setup menus

(page 100)



12

Making maximum use of the remote

control

• Operating multiple receivers (page 77)

• Setting the remote to control other

components (page 77)

• Programming signals from other remote

controls (page 78)

VSX-1020_SYXCN.book 7 ページ２０１０年３月１２日　金曜日　午前９時１０分

Before you start01

8

En

Chapter 1:

Before you start

Checking what’s in the box

Please check that you’ve received the following

supplied accessories:

• Setup microphone (cable: 5 m)

• Remote control unit

• AAA size IEC R03 dry cell batteries (to

confirm system operation) x2

•AM loop antenna

•FM wire antenna

•iPod cable

•Power cord

•

Warranty card

• These operating instructions

Installing the receiver

• When installing this unit, make sure to put

it on a level and stable surface.

Don’t install it on the following places:

– on a color TV (the screen may distort)

– near a cassette deck (or close to a device that

gives off a magnetic field). This may interfere

with the sound.

– in direct sunlight

– in damp or wet areas

– in extremely hot or cold areas

– in places where there is vibration or other

movement

– in places that are very dusty

– in places that have hot fumes or oils (such as

a kitchen)

• Do not touch this receiver’s bottom panel

while the power is on or just after it is

turned off. The bottom panel becomes hot

when the power is on (or right after it is

turned off) and could cause burns.

Loading the batteries

The batteries included with the unit are to

check initial operations; they may not last over

a long period. We recommend using alkaline

batteries that have a longer life.

CAUTION

Incorrect use of batteries may result in such

hazards as leakage and bursting. Observe the

following precautions:

• Never use new and old batteries together.

• Insert the plus and minus sides of the

batteries properly according to the marks

in the battery case.

• Batteries with the same shape may have

different voltages. Do not use different

batteries together.

• When disposing of used batteries, please

comply with governmental regulations or

environmental public instruction’s rules

that apply in your country or area.

• WARNING

Do not use or store batteries in direct

sunlight or other excessively hot place,

such as inside a car or near a heater. This

can cause batteries to leak, overheat,

explode or catch fire. It can also reduce the

life or performance of batteries.

VSX-1020_SYXCN.book 8 ページ２０１０年３月１２日　金曜日　午前９時１０分

Controls and displays 02

9

En

English

Français

Deutsch

Nederlands

Italiano

Español

Chapter 2:

Controls and displays

Front panel

1

INPUT SELECTOR

dial

Select an input function.

2

 STANDBY/ON

Switches the receiver between on and standby.

3

SPEAKERS

See Switching the speaker terminals on

page 73.

4 Remote sensor

Receives the signals from the remote control

(see Operating range of remote control unit on

page 14).

5

MULTI-ZONE

controls

If you’ve made MULTI-ZONE connections (see

MULTI-ZONE setup on page 32) use these

controls to control the sub zone from the main

zone (see Using the MULTI-ZONE controls on

page 73).

6 Character display

See Display on page 11.

7Indicators

ADVANCED MCACC

– Lights when

EQ

is

set to

ON

in the

AUDIO PARAMETER

menu.

PQLS – Lights when the PQLS feature is

active (page 66).

HDMI – Blinks when connecting an HDMI-

equipped component; lights when the

component is connected (page 25).

SPEAKERS

AUTO/ALC/DIRECT STEREO STANDARD

LISTENING MODE

ADV SURROUND DIRECT CONTROL

iPod iPhone

CONTROL ON/OFFMULTI-ZONE

PQLS HDMI BAND TUNER EDITiPhone

iPod

MCACC

ADVANCED

TUNE

PRESET PRESET

ENTER

PHONES

INPUT

SELECTOR

STANDBY/ON

PHASE

CONTROL

MASTER

VOLUME

MCACC

SETUP MIC

AUDIO/ VIDEO MULTI- CHANNEL RECEIVER

VSX

-1020

VIDEO CAMERA

iPod

iPhone

USB HDMI 5

MCACC

SETUP MIC

VIDEO 2 INPUT

AUDIOLRVIDEO

iPod

iPhone

USB

12 73 5 8

10

11 1412 13

14 16 13

15

49

6

VSX-1020/VSX-1025

VSX-920

VSX-1020_SYXCN.book 9 ページ２０１０年３月１２日　金曜日　午前９時１０分

Controls and displays02

10

En

iPod/iPhone – Lights to indicate iPod/

iPhone is connected (page 45).

8 Tuner controls

BAND – Switches between the AM and FM

radio bands (page 50).

TUNER EDIT –

Use with

TUNE /

,

PRESET /

and

ENTER

to memorize and

name stations for recall

(page 50)

.

TUNE / –

Find radio frequencies

(page 50)

.

PRESET / – Find preset stations

(page 50).

9

MASTER VOLUME

dial

10

PHONES

jack

Connect the headphones. When the

headphones are connected, there is no sound

output from the speakers.

11 Listening mode buttons

AUTO/ALC/DIRECT – Switches between

Auto Surround (page 57), Auto Level

Control mode and Stream Direct mode

(page 60).

STEREO – Switches between stereo

playback and Front Stage Surround

Advance modes (page 60).

STANDARD – Press for Standard decoding

and to switch between the various 2 Pro

Logic IIx and Neo:6 options (page 57).

ADV SURROUND – Switch between the

various surround modes (page 59).

12

iPod iPhone DIRECT CONTROL

Change the receiver’s input to the iPod and

enable iPod operations on the iPod (page 46).

13

MCACC SETUP MIC

jack

Connect the supplied microphone (page 39).

14

iPod/iPhone/USB

terminals

Connect your Apple iPod as an audio and video

source, or connect a USB device for audio and

photo playback (page 35, 36).

15

VSX-1020/VSX-1025 only:

HDMI input

connector

Use for connection to a compatible HDMI

device (Video camera, etc.)(page 34).

16

VSX-920 only:

VIDEO 2 INPUT terminals

Use to connect your portable equipment such

as camcorders, video games and portable

audio/video equipment (page 35).

VSX-1020_SYXCN.book 10 ページ２０１０年３月１２日　金曜日　午前９時１０分

Controls and displays 02

11

En

English

Français

Deutsch

Nederlands

Italiano

Español

Display

1

SIGNAL

indicators

Light to indicate the currently selected input

signal. AUTO lights when the receiver is set to

select the input signal automatically (page 61).

2 Program format indicators

Light to indicate the channels to which digital

signals are being input.

L/R – Left front/Right front channel

C – Center channel

SL/SR – Left surround/Right surround channel

LFE

– Low frequency effects channel (the

(( ))

indicators light when an LFE signal is being input)

XL/XR – Two channels other than the ones above

XC – Either one channel other than the ones

above, the mono surround channel or matrix

encode flag

3 Digital format indicators

Light when a signal encoded in the

corresponding format is detected.

2

DIGITAL

– Lights with Dolby Digital decoding.

2 DIGITAL PLUS – Lights with Dolby Digital

Plus decoding.

2

TrueHD

– Lights with Dolby TrueHD decoding.

DTS

– Lights with DTS decoding.

DTS HD – Lights with DTS-HD decoding.

96/24 – Lights with DTS 96/24 decoding.

WMA9 Pro – Lights to indicate that a WMA9 Pro

signal is being decoded.

DSD PCM – Light during DSD (Direct Stream

Digital) to PCM conversion with SACDs.

PCM – Lights during playback of PCM signals.

MSTR – Lights during playback of DTS-HD

Master Audio signal.

4

MULTI-ZONE

Lights when the MULTI-ZONE feature is active

(page 73).

5

SOUND

Lights when any of the Midnight, Loudness or

tone controls feature is selected (page 68).

Lights when Dialog Enhancement is switched on.

6

S.RTRV

Lights when the Sound Retriever function is

active (page 69).

7 Listening mode indicators

AUTO SURROUND – Lights when the

Auto Surround feature is switched on

(page 57).

ALC – Lights when the ALC (Auto level

control) mode is selected (page 60).

STREAM DIRECT – Lights when Direct/

Pure Direct is selected (page 60).

ADV.SURROUND – Lights when one of the

Advanced Surround modes has been

selected (page 59).

STEREO – Lights when stereo listening is

switched on (page 59).

STANDARD – Lights when one of the

Standard Surround modes is switched on

(page 57).

8 (PHASE CONTROL)

Lights when Phase Control is switched on

(page 62).

SIRIUS

PCM

HDMI

DIGITAL

ANALOG

L C R

SL SR

XL XR

XC

LFE

AUTO

DIGITAL PLUS

AUTO SURROUND

STREAM DIRECT

PROLOGIC

x

Neo:6

ADV.SURROUND

STEREO STANDARD

SP

AB

SLEEP

DSD PCM

DTS HD ES 96/24

MSTR

S.RTRV SOUND UP MIX

OVER

MONO

dB

2

MULTI-ZONE STEREO

TrueHD

WMA9Pro

TUNED

RDS

PQLS

ALC

ATT

2

USB

VIDEO

TV

DVD

HDMI

DVR

BD

CD

TUNER

CD-R

iPod

[ 2 ]

[ 3 ]

[ 4 ]

21 3 9754 108

11

12 13

18 1915 16 17

14

7

6

VSX-1020_SYXCN.book 11 ページ２０１０年３月１２日　金曜日　午前９時１０分

Controls and displays02

12

En

9 Analog signal indicators

Light to indicate reducing the level of an analog

signal (page 75).

10 Tuner indicators

TUNED – Lights when a broadcast is being

received.

STEREO –

Lights when a stereo FM broadcast

is being received in auto stereo mode.

MONO – Lights when the mono mode is

set using MPX.

RDS – Lights when an RDS broadcast is

received.

11

Lights when the sound is muted (page 14).

12 Master volume level

Shows the overall volume level.

“---” indicates the minimum level, and “+12dB”

indicates the maximum level.

13 Input function indicators

Light to indicate the input function you have

selected.

14 Scroll indicators

Light when there are more selectable items

when making the various settings.

15 Speaker indicators

Indicates the speaker terminal, A and/or B, to

which audio signal output is currently set

(page 73).

16

SLEEP

Lights when the receiver is in sleep mode

(page 75).

17 Matrix decoding format indicators

2PRO LOGIC IIx – This lights to indicate

2 Pro Logic II / 2 Pro Logic IIx decoding

(page 57).

Neo:6 – When one of the Neo:6 modes of

the receiver is on, this lights to indicate

Neo:6 processing (page 57).

18 Character display

Displays various system information.

19 Remote control mode indicator

Lights to indicate the receiver’s remote control

mode setting. (Not displayed when set to 1.)

(page 77)

VSX-1020_SYXCN.book 12 ページ２０１０年３月１２日　金曜日　午前９時１０分

Controls and displays 02

13

En

English

Français

Deutsch

Nederlands

Italiano

Español

Remote control

This section explains how to operate the

remote control for the receiver.

The remote has been conveniently color-coded

according to component control using the

following system:

• White – Receiver control, TV control

• Blue – Other controls (See page 45, 47, 50,

53, 55 and 83.)

1  RECEIVER

This switches between standby and on for this

receiver.

2

MULTI OPERATION – Use to perform

multi operations (page 81).

R.SETUP – Use to input the preset code

when making remote control settings and

to set the remote control mode (page 77).

3 Input function buttons

Press to select control of other components

(page 77).

4

ZONE 2

Switch to perform operations in the sub zone

(page 74).

5

TV CONTROL

buttons

These buttons are dedicated to control the TV

assigned to the TV CTRL button.

 – Turn on/off the power of the TV.

INPUT – Select the TV input signal.

CH +/– – Select channels.

VOL +/– – Adjust the volume on your TV.

6 Receiver controls

Press first to access:

AUDIO PARAMETER – Use to access the

Audio options (page 68).

VIDEO PARAMETER – Use to access the

Video options (page 71).

HOME MENU – Use to access the Home

Menu (pages 39, 42, 64, 86, 100 and 106).

RETURN – Press to confirm and exit the

current menu screen.

RECEIVER

LISTENING MODE

AUTO

/

ALC

/

DIRECT

STEREO

D.ACCESS

CH

LEVEL A.ATT DIMMER

SIGNAL SEL

S.RETRIEVER

MCACC SLEEP

MIDNIGHT

TV

/

DTV MPX PQLS

PHASE

CTRL STATUS

PGM

iPod CTRL

HOME

MENU

TUNE

TOOLS

LIST

CH

TV CONTROL

INPUT

SELECT ZONE 2

iPod

USB TUNER VIDEO TV CTRL

ADAPTERNET RADIO

CDTV

BD DVD

R.SETUP

SOURCERECEIVER

MULTI

OPERATION

DVR/BDR HDMI

RECEIVER

MUTE

MASTER

VOLUME

VOL

PRESET

TOP MENU

BAND GUIDE

T.EDIT

VIDEO

PARAMETER

AUDIO

PARAMETER

ENTER

PRESET

RETURN

PTY

SEARCH

MENU

AUDIO

INFO

CLASS

ENTER

DISP

HDD DVD

546

8

0

79

213

/

CLR

CH

STANDARD ADV SURR

1

2

3

4

8

9

5

6

7

10

11

12

13

14

RECEIVER

VSX-1020_SYXCN.book 13 ページ２０１０年３月１２日　金曜日　午前９時１０分

Controls and displays02

14

En

7

///

,

ENTER

Use the arrow buttons when setting up your

surround sound system (page 86) and the

Audio or Video options (page 68 or 71).

8 Receiver controls

Press first to access:

PHASE CTRL – Switch on/off Phase Control

(page 62).

STATUS – Check selected receiver settings

(page 75).

PQLS – Select the PQLS setting (page 66).

S.RETRIEVER – Press to restore CD quality

sound to compressed audio sources

(page 69).

MIDNIGHT – Switches to Midnight or

Loudness listening (page 68).

SIGNAL SEL – Select an input signal

(page 61).

MCACC – Switch between MCACC presets

(page 61).

SLEEP – Use to put the receiver in sleep

mode and select the amount of time before

sleep (page 75).

CH LEVEL – Press repeatedly to select a

channel, then use / to adjust the level

(page 103).

A.ATT – Attenuates (lowers) the level of an

analog input signal to prevent distortion

(page 75).

DIMMER – Dims or brightens the display

(page 75).

9 LISTENING MODE controls

AUTO/ALC/DIRECT –

Switches between

Auto Surround

(page 57)

, Auto Level

Control mode and Stream Direct mode

(page 60).

STEREO – Switches between stereo

playback and Front Stage Surround

Advance modes (page 60).

STANDARD – Press for Standard decoding

and to switch between the various 2 Pro

Logic IIx and Neo:6 options (page 57).

ADV SURR – Switch between the various

surround modes (page 59).

10 Remote control LED

Lights when a command is sent from the

remote control (page 77).

11

TV CTRL

Set the preset code of your TV’s manufacturer

when controlling TV (page 78).

12

Switches the remote to control the receiver

(used to select the white commands (SIGNAL

SEL, etc.)).

Switch to perform operations in the main zone.

Also use to set up surround sound.

13

MASTER VOLUME +/–

Set the listening volume.

14

MUTE

Mutes the sound or restores the sound if it has

been muted (adjusting the volume also

restores the sound).

Operating range of remote control

unit

The remote control may not work properly if:

• There are obstacles between the remote

control and the receiver’s remote sensor.

• Direct sunlight or fluorescent light is

shining onto the remote sensor.

• The receiver is located near a device that is

emitting infrared rays.

• The receiver is operated simultaneously

with another infrared remote control unit.

RECEIVER

7 m

30°

VSX-1020_SYXCN.book 14 ページ２０１０年３月１２日　金曜日　午前９時１０分

Connecting your equipment 03

15

En

English

Français

Deutsch

Nederlands

Italiano

Español

Chapter 3:

Connecting your equipment

This receiver provides you with many connection possibilities, but it doesn’t have to be difficult.

This page explains the kinds of components you can connect to make up your home theater system.

Important

• Illustration shows the VSX-1020, however connections for the VSX-1025 and the VSX-920 are

the same except where noted.

Rear panel

HDMI

ASSIGNABLE

PB

PR

ASSIGNABLE

(

DVD

)

(

DVR/BDR

)

(

DVD

)

Y

P

B

PR

Y

P

B

PR

Y

L

R

FRONT CENTER SURROUND

SURROUND BACK

FRONT HEIGHT/WIDE/

LR LR L

RL

ZONE 2

OUT

DVR/BDR

DVD

OUT IN

CD-R/TAPE

OUT ININ

CD

IN

TV/SAT

IN

VIDEO

IN

(

DVR/BDR

)

(

OUTPUT 5 V 100 mA MAX

)

(

CD

)

(

Single

)

SUBWOOFER

(

TV/SAT

)

AM LOOP

FM UNBAL 75

COMPONENT VIDEO

AUDIO

PRE OUT

ANTENNA

OPTICAL

ADAPTER PORT

VIDEO

IR CONTROL

SPEAKERS

MONITOR

OUT

LAN

COAXIAL

BD IN IN IN IN IN

OUT

(

10/100

)

IN

1

IN

2

1

IN

1

IN

2

1 4

2 3 4

IN

1

A

IN

2

B

IN

OUT

IN

OUT

AC IN

VSX-1020/VSX-1025

HDMI

ASSIGNABLE

PB

PR

ASSIGNABLE

(

DVD

)

(

DVR/BDR

)

(

DVD

)

Y

P

B

PR

Y

P

B

PR

Y

L

R

FRONT CENTER SURROUND

SURROUND BACK

FRONT HEIGHT/WIDE/

LR LR L

RL

ZONE 2

OUT

DVR/BDR

DVD

OUT IN

CD-R/TAPE

OUT ININ

CD

IN

TV/SAT

IN

VIDEO 1

IN

(

DVR/BDR

)

(

OUTPUT 5 V 100 mA MAX

)

(

Single

)

SUBWOOFER

(

TV/SAT

)

AM LOOP

FM UNBAL 75

COMPONENT VIDEO

AUDIO

PRE OUT

ANTENNA

OPTICAL

ADAPTER PORT

VIDEO

IR CONTROL

SPEAKERS

MONITOR

OUT

LAN

COAXIAL

BD IN IN IN IN

OUT

(

10/100

)

IN

1

IN

1

IN

2

1 3

2 3

IN

1

A

IN

2

B

IN

OUT

IN

OUT

AC IN

VSX-920

VSX-1020_SYXCN.book 15 ページ２０１０年３月１２日　金曜日　午前９時１０分

Connecting your equipment03

16

En

CAUTION

• Before making or changing the

connections, switch off the power and

disconnect the power cord from the power

outlet. Plugging in should be the final step.

Important

• The input functions below are assigned by

default to the receiver’s different input

terminals. Refer to The Input Setup menu

on page 42 to change the assignments if

other connections are used.

Input

function

Input Terminals

Digital HDMI

Component

DVD COAX-1 IN 1

BD (BD)

TV/SAT OPT-1

DVR/BDR OPT-2 IN 2

HDMI 1

(HDMI-1)

HDMI 2

(HDMI-2)

HDMI 3

(HDMI-3)

HDMI 4

a

a. VSX-1020/VSX-1025 only

(HDMI-4)

HDMI 5

a

(front panel)

(HDMI-5)

CD COAX-2

a

VSX-1020_SYXCN.book 16 ページ２０１０年３月１２日　金曜日　午前９時１０分

Connecting your equipment 03

17

En

English

Français

Deutsch

Nederlands

Italiano

Español

Determining the speakers’

application

This unit permits you to build various surround

systems, in accordance with the number of

speakers you have.

• Be sure to connect speakers to the front

left and right channels (L and R).

• It is also possible to only connect one of the

surround back speakers (SB) or neither.

Choose one from Plans [A] to [E] below.

[A] 9.1 channel surround system (Front

height)

*Default setting

• Speaker System setting: Normal(SB/FH)

A 9.1 ch surround system connects the left and

right front speakers (L/R), the center speaker

(C), the left and right front height speakers

(FHL/FHR), the left and right surround

speakers (SL/SR), the left and right surround

back speakers (SBL/SBR), and the subwoofer

(SW).

This surround system produces a more true-to-

life sound from above.

[B] 9.1 channel surround system (Front

wide)

•

Speaker System setting: Normal(SB/FW)

This plan replaces the left and right front

height speakers shown in [A] with the left and

right front wide speakers (FWL/FWR).

This surround system produces a true-to-life

sound over a wider area.

[C] 7.1 channel surround system &

Speaker B connection

• Speaker System setting: Speaker B

With these connections you can

simultaneously enjoy 5.1-channel surround

sound in the main zone with stereo playback of

the same sound on the B speakers. The same

connections also allow for 7.1-channel

surround sound in the main zone when not

using the B speakers.

SL

L

FHL

SW

C

R

FHR

SR

SBL

SBR

FWR

FWL

SL

L

SW

C

R

SR

SBL

SBR

SL

L

SW

C

R

SR

SBL

SBR

L

R

Speaker B

VSX-1020_SYXCN.book 17 ページ２０１０年３月１２日　金曜日　午前９時１０分

Connecting your equipment03

18

En

[D] 5.1 channel surround system & Front

Bi-amping connection (High quality

surround)

• Speaker System setting: Front Bi-Amp

Bi-amping connection of the front speakers for

high sound quality with 5.1-channel surround

sound.

[E] 5.1 channel surround system & ZONE

2 connection (Multi Zone)

• Speaker System setting: ZONE 2

With these connections you can

simultaneously enjoy 5.1-channel surround

sound in the main zone with stereo playback

on another component in ZONE 2 (The

selection of input devices is limited.)

Important

•The Speaker System setting must be

made if you use any of the connections

shown above other than [A] (see Speaker

system setting on page 101).

• Sound does not come through

simultaneously from the front height, front

wide, speaker B and surround back

speakers. Output speakers are different

depending on the input signal or listening

mode.

Other speaker connections

• Your favorite speaker connections can be

selected even if you have fewer than 5.1

speakers (except front left/right speakers).

• When not connecting a subwoofer,

connect speakers with low frequency

reproduction capabilities to the front

channel. (The subwoofer’s low frequency

component is played from the front

speakers, so the speakers could be

damaged.)

• After connecting, be sure to conduct

the Auto MCACC (speaker environment

setting) procedure.

See Automatically conducting optimum

sound tuning (Auto MCACC) on page 39.

L

R

SL

SW

C

SR

Front Bi-Amp

L

R

SL

SW

C

SR

ZONE 2

Main zone

Sub zone

VSX-1020_SYXCN.book 18 ページ２０１０年３月１２日　金曜日　午前９時１０分

Connecting your equipment 03

19

En

English

Français

Deutsch

Nederlands

Italiano

Español

Placing the speakers

Refer to the chart below for placement of the

speakers you intend to connect.

• Place the surround speakers at 120º from

the center. If you, (1) use the surround back

speaker, and, (2) don’t use the front height

speakers / front wide speakers, we

recommend placing the surround speaker

right beside you.

• If you intend to connect only one surround

back speaker, place it directly behind you.

• Place the left and right front height

speakers at least 1 m directly above the left

and right front speakers.

Some tips for improving sound quality

Where you put your speakers in the room has

a big effect on the quality of the sound. The

following guidelines should help you to get the

best sound from your system.

• The subwoofer can be placed on the floor.

Ideally, the other speakers should be at

about ear-level when you’re listening to

them. Putting the speakers on the floor

(except the subwoofer), or mounting them

very high on a wall is not recommended.

• For the best stereo effect, place the front

speakers 2 m to 3 m apart, at equal

distance from the TV.

• If you’re going to place speakers around

your CRT TV, use shielded speakers or

place the speakers at a sufficient distance

from your CRT TV.

• If you’re using a center speaker, place the

front speakers at a wider angle. If not,

place them at a narrower angle.

• Place the center speaker above or below

the TV so that the sound of the center

channel is localized at the TV screen. Also,

make sure the center speaker does not

cross the line formed by the leading edge

of the front left and right speakers.

• It is best to angle the speakers towards the

listening position. The angle depends on

the size of the room. Use less of an angle

for bigger rooms.

• Surround and surround back speakers

should be positioned 60 cm to 90 cm higher

than your ears and tilted slightly downward.

Make sure the speakers don’t face each

other. For DVD-Audio, the speakers should

be more directly behind the listener than for

home theater playback.

• Try not to place the surround speakers

farther away from the listening position

than the front and center speakers. Doing

so can weaken the surround sound effect.

L

SW

C

FHL

FWL

SL

SBL

SBR

SB

SR

FWR

R

FHR

30 30

60

120 120

VSX-1020_SYXCN.book 19 ページ２０１０年３月１２日　金曜日　午前９時１０分

Connecting your equipment03

20

En

Connecting the speakers

Each speaker connection on the receiver

comprises a positive (+) and negative (–)

terminal. Make sure to match these up with the

terminals on the speakers themselves.

CAUTION

• These speaker terminals carry

HAZARDOUS LIVE voltage. To prevent

the risk of electric shock when connecting

or disconnecting the speaker cables,

disconnect the power cord before touching

any uninsulated parts.

• Make sure that all the bare speaker wire is

twisted together and inserted fully into the

speaker terminal. If any of the bare speaker

wire touches the back panel it may cause

the power to cut off as a safety measure.

Bare wire connections

A-Speaker terminals:

1 Twist exposed wire strands together.

2 Loosen terminal and insert exposed wire.

3 Tighten terminal.

B-Speaker terminals:

1 Twist exposed wire strands together.

2 Push open the tabs and insert exposed

wire.

3 Release the tabs.

Important

• Please refer to the manual that came with

your speakers for details on how to connect

the other end of the speaker cables to your

speakers.

• Use an RCA cable to connect the subwoofer.

It is not possible to connect using speaker

cables.

CAUTION

• Make sure that all speakers are securely

installed. This not only improves sound

quality, but also reduces the risk of

damage or injury resulting from speakers

being knocked over or falling in the event of

external shocks such as earthquakes.

12 3

10 mm

12 3

10 mm

VSX-1020_SYXCN.book 20 ページ２０１０年３月１２日　金曜日　午前９時１０分

La page charge ...

Pioneer VSX-1020-K Le manuel du propriétaire

Ce manuel convient également à

Pioneer VSX-1020-K Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents