Pioneer VSX-820-S Silver Manuel utilisateur

Operating Instructions

Mode d’emploi

Инструкции по эксплуатации

Discover the benefits of registering your product online at

http://www.pioneer.co.uk

(or http://www.pioneer.eu).

Découvrez les nombreux avantages offerts en enregistrant votre produit en ligne

maintenant sur

http://www.pioneer.fr

(ou http://www.pioneer.eu).

Зарегистрируйте Baшe изделие на

http://www.pioneer-rus.ru

(или

http://www.pioneer.eu). Oзнакомьтесь с преимуществами регистрации в Интернет

VSX-820

-S/-K

VSX-820_SYXCN_En.book 1 ページ２０１０年４月１２日　月曜日　午後６時５２分

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 40 cm at top, 10 cm at rear, and 20 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

D3-4-2-1-2-2*_A1_En

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified

service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug. Should

the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to

BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug

must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of

safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows;

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

VSX-820_SYXCN_En.book 2 ページ２０１０年４月１２日　月曜日　午後６時５２分

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Pb

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left unused

for a long period of time (for example, when on

vacation).

D3-4-2-2-1a_A1_En

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

Manufactured under license from Dolby

Laboratories. Dolby, Pro Logic, Surround EX

and the double-D symbol are trademarks of

Dolby Laboratories.

Manufactured under license under U.S.

Patent #’s: 5,451,942; 5,956,674; 5,974,380;

5,978,762; 6,226,616; 6,487,535; 7,212,872;

7,333,929; 7,392,195; 7,272,567 & other U.S.

and worldwide patents issued & pending.

DTS and the Symbol are registered

trademarks, & DTS-HD, DTS-HD Master

Audio, and the DTS logos are trademarks of

DTS, Inc. Product includes software. © DTS,

VSX-820_SYXCN_En.book 3 ページ２０１０年４月１２日　月曜日　午後６時５２分

4

En

Thank you for buying this Pioneer product. Please read through these operating instructions so you

will know how to operate your model properly. After you have finished reading the instructions, put

them away in a safe place for future reference.

Contents

Flow of settings on the receiver

. . 6

01 Before you start

Checking what’s in the box . . . . . . . . . . . . . . . 7

Loading the batteries . . . . . . . . . . . . . . . . . . . 7

Installing the receiver . . . . . . . . . . . . . . . . . . . 7

Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . 8

02 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operating range of remote control . . . . . . . 10

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Remote control . . . . . . . . . . . . . . . . . . . . . . . 13

03 Connecting your equipment

Placing the speakers. . . . . . . . . . . . . . . . . . . 16

Hints on the speaker placement. . . . . . . . . 17

Connecting the speakers . . . . . . . . . . . . . . . 18

Connect the surround back or front

height speakers . . . . . . . . . . . . . . . . . . . . . 19

Switching the speaker system . . . . . . . . . . 20

Making cable connections . . . . . . . . . . . . . . 20

HDMI cables . . . . . . . . . . . . . . . . . . . . . . . 20

About HDMI . . . . . . . . . . . . . . . . . . . . . . . . 21

Analog audio cables. . . . . . . . . . . . . . . . . . 21

Digital audio cables . . . . . . . . . . . . . . . . . . 21

Video cables . . . . . . . . . . . . . . . . . . . . . . . . 21

About video outputs connection . . . . . . . . . . 22

Connecting a TV and playback components

. . . 23

Connecting using HDMI. . . . . . . . . . . . . . . 23

Connecting your component with no

HDMI terminal . . . . . . . . . . . . . . . . . . . . . . 24

Connecting a satellite receiver or other

digital set-top box . . . . . . . . . . . . . . . . . . . . . 25

Connecting an HDD/DVD recorder, VCR

and other video sources . . . . . . . . . . . . . . . . 25

Using the component video jacks . . . . . . . . . 26

Connecting other audio components . . . . . . 26

Connecting antennas . . . . . . . . . . . . . . . . . . 27

Using external antennas. . . . . . . . . . . . . . . 27

Connecting to the front panel video

terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Plugging in the receiver . . . . . . . . . . . . . . . . 28

04 Basic Setup

Automatically setting up for surround

sound (MCACC) . . . . . . . . . . . . . . . . . . . . . . 29

Other problems when using the Auto

MCACC Setup. . . . . . . . . . . . . . . . . . . . . . . 31

05 Listening to your system

Basic playback . . . . . . . . . . . . . . . . . . . . . . . 32

Auto playback . . . . . . . . . . . . . . . . . . . . . . . . 33

Listening in surround sound . . . . . . . . . . . . . 33

Using the Advanced surround effects. . . . . 34

Listening in stereo. . . . . . . . . . . . . . . . . . . . . 35

Using Front Stage Surround Advance . . . . . . 35

Using Stream Direct . . . . . . . . . . . . . . . . . . . 36

Using the Sound Retriever. . . . . . . . . . . . . . . 36

Better sound using Phase Control. . . . . . . . . 36

Listening with Acoustic Calibration EQ . . . . . 37

Using surround back channel processing. . . 37

Setting the Up Mix function. . . . . . . . . . . . . . 38

Setting the Audio options . . . . . . . . . . . . . . . 38

Choosing the input signal . . . . . . . . . . . . . . . 41

Using the headphone . . . . . . . . . . . . . . . . . . 41

06 The System Setup menu

Using the System Setup menu . . . . . . . . . . . 42

Manual speaker setup. . . . . . . . . . . . . . . . . . 43

Speaker Setting . . . . . . . . . . . . . . . . . . . . . 43

Crossover Network . . . . . . . . . . . . . . . . . . . 45

Channel Level . . . . . . . . . . . . . . . . . . . . . . . 45

Speaker Distance . . . . . . . . . . . . . . . . . . . . 46

The Input Assign menu . . . . . . . . . . . . . . . . . 46

The Pre Out Setting . . . . . . . . . . . . . . . . . . . . 47

07 Using the tuner

Listening to the radio. . . . . . . . . . . . . . . . . . . 48

Improving FM stereo sound . . . . . . . . . . . . 48

Saving station presets . . . . . . . . . . . . . . . . . . 48

Listening to station presets. . . . . . . . . . . . . 49

Naming preset stations. . . . . . . . . . . . . . . . 49

An introduction to RDS . . . . . . . . . . . . . . . . . 50

Searching for RDS programs . . . . . . . . . . . 50

Displaying RDS information . . . . . . . . . . . . 51

VSX-820_SYXCN_En.book 4 ページ２０１０年４月１２日　月曜日　午後６時５２分

English Italiano Français

Nederlands

EspañolDeutsch

English

Français

Deutsch

Nederlands

Italiano

Español

5

En

08 Making recordings

Making an audio or a video recording . . . . . . 52

09

Controlling the rest of your system

Setting the remote to control other

components . . . . . . . . . . . . . . . . . . . . . . . . . 53

Selecting preset codes directly . . . . . . . . . . . 53

Clearing all the remote control settings. . . . . 54

Controls for TVs . . . . . . . . . . . . . . . . . . . . . . . 55

Controls for other components . . . . . . . . . . . 56

Preset Code List . . . . . . . . . . . . . . . . . . . . . . 57

10 Other connections

Connecting an iPod. . . . . . . . . . . . . . . . . . . . 66

Connecting your iPod to the receiver . . . . . 66

iPod playback . . . . . . . . . . . . . . . . . . . . . . . 67

Watching photos and video content . . . . . . 68

About iPod . . . . . . . . . . . . . . . . . . . . . . . . . 68

Connecting a USB device . . . . . . . . . . . . . . . 69

Connecting your USB device to the

receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Basic playback controls . . . . . . . . . . . . . . . 69

Compressed audio compatibility. . . . . . . . . 70

Bluetooth® ADAPTER for Wireless

Enjoyment of Music. . . . . . . . . . . . . . . . . . . . 71

Wireless music play . . . . . . . . . . . . . . . . . . 71

Connecting Optional Bluetooth

ADAPTER . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Pairing Bluetooth ADAPTER and

Bluetooth wireless technology device . . . . . 72

Listening to Music Contents of

Bluetooth wireless technology device

with Your System . . . . . . . . . . . . . . . . . . . . 72

11 Additional information

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 74

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Important information regarding the

HDMI connection . . . . . . . . . . . . . . . . . . . . 78

iPod messages . . . . . . . . . . . . . . . . . . . . . . 78

USB messages . . . . . . . . . . . . . . . . . . . . . . 79

Resetting the main unit. . . . . . . . . . . . . . . . . 79

Specifications . . . . . . . . . . . . . . . . . . . . . . . . 80

Cleaning the unit. . . . . . . . . . . . . . . . . . . . . . 80

VSX-820_SYXCN_En.book 5 ページ２０１０年４月１２日　月曜日　午後６時５２分

6

En

Flow of settings on the receiver

The unit is a full-fledged AV receiver equipped

with an abundance of functions and terminals.

It can be used easily after following the

procedure below to make the connections and

settings.

The colors of the steps indicate the following:

Required setting item

Setting to be made as necessary

1

Before you start

• Checking what’s in the box (page 7)

• Loading the batteries (page 7)



2

Connecting the speakers

Where you place the speakers will have a big

effect on the sound. Place your speakers as

shown below for the best surround sound effect.

• Placing the speakers (page 16)

• Connecting the speakers (page 18)

• Connect the surround back or front height

speakers (page 19)

You can connect only one of either the surround back

speaker or the front height speaker.



3

Connecting the components

For surround sound, you’ll want to hook up

using a digital connection from the BD/DVD

player to the receiver.

• About video outputs connection (page 22)

• Connecting a TV and playback components

(page 23)

• Connecting antennas (page 27)

• Plugging in the receiver (page 28)



Front

Left (L)

*Front Height

Left (FHL)

*Front Height

Right (FHR)

Surround

Left (SL)

*Surround Back

Left (SBL)

*Surround Back

Right (SBR)

Surround

Right (SR)

Center (C)

Subwoofer (SW)

Listening

position

Front

Right (R)



4

Power On

Make sure you’ve set the video input on your TV to

this receiver. Check the manual that came with

the TV if you don’t know how to do this.



5

The Pre Out Setting (page 47)

(When connecting the front height speakers.)

The Input Assign menu (page 46)

(When using connections other than the

recommended connections.)



6

Use the on-screen automatic MCACC

setup to set up your system

• Automatically setting up for surround sound

(MCACC) (page 29)



7

Basic playback (page 32)



8

Adjusting the sound as desired

•Using the various listening modes

• Using the Sound Retriever (page 36)

• Better sound using Phase Control (page 36)

• Listening with Acoustic Calibration EQ

(page 37)

• Using surround back channel processing

(page 37)

• Setting the Up Mix function (page 38)

• Setting the Audio options (page 38)

• Choosing the input signal (page 41)

• Manual speaker setup (page 43)



9

Making maximum use of the remote

control

• Setting the remote to control other

components (page 53)

VSX-820_SYXCN_En.book 6 ページ２０１０年４月１２日　月曜日　午後６時５２分

Before you start 01

7

En

English

Français

Deutsch

Nederlands

Italiano

Español

Chapter 1:

Before you start

Checking what’s in the box

Please check that you’ve received the following

supplied accessories:

• Setup microphone

• Remote control

• Dry cell batteries (AAA size IEC R03) x2

• AM loop antenna

•FM wire antenna

• iPod cable

•Power cord

• Warranty card

• These operating instructions

Loading the batteries

The batteries included with the unit are to

check initial operations; they may not last over

a long period. We recommend using alkaline

batteries that have a longer life.

CAUTION

Incorrect use of batteries may result in such

hazards as leakage and bursting. Observe the

following precautions:

• Never use new and old batteries together.

• Insert the plus and minus sides of the

batteries properly according to the marks

in the battery case.

• Batteries with the same shape may have

different voltages. Do not use different

batteries together.

• When disposing of used batteries, please

comply with governmental regulations or

environmental public instruction’s rules

that apply in your country or area.

• Do not use or store batteries in direct

sunlight or other excessively hot place,

such as inside a car or near a heater. This

can cause batteries to leak, overheat,

explode or catch fire. It can also reduce

the life or performance of batteries.

Installing the receiver

• When installing this unit, make sure to put

it on a level and stable surface.

Don’t install it on the following places:

– on a color TV (the screen may distort)

– near a cassette deck (or close to a device

that gives off a magnetic field). This may

interfere with the sound.

– in direct sunlight

– in damp or wet areas

– in extremely hot or cold areas

– in places where there is vibration or other

movement

– in places that are very dusty

– in places that have hot fumes or oils (such as

a kitchen)

VSX-820_SYXCN_En.book 7 ページ２０１０年４月１２日　月曜日　午後６時５２分

Before you start01

8

En

Ventilation

When installing this unit, make sure to leave

space around the unit for ventilation to improve

heat dispersal (at least 40 cm at the top). If not

enough space is provided between the unit and

walls or other equipment, heat will build up

inside, interfering with performance and/or

causing malfunctions.

Slot and openings in the cabinet are provided

for ventilation and to protect the equipment

from overheating. To prevent fire hazard, do not

place anything directly on top of the unit, make

sure the openings are never blocked or covered

with items (such as newspapers, table-cloths

and curtains), and do not operate the

equipment on thick carpet or a bed.

Receiver

40 cm

VSX-820_SYXCN_En.book 8 ページ２０１０年４月１２日　月曜日　午後６時５２分

Controls and displays 02

9

En

English

Français

Deutsch

Nederlands

Italiano

Español

Chapter 2:

Controls and displays

Front panel

1

 STANDBY/ON

2

INPUT SELECTOR

dial

Selects an input source.

3

MCACC

indicator

Lights when Acoustic Calibration EQ (page 37)

is on (Acoustic Calibration EQ is automatically

set to on after the Auto MCACC Setup

(page 29)).

4 Remote sensor

Receives the signals from the remote control

(see Operating range of remote control on

page 10).

5

SPEAKERS

Use to change the speaker system (page 20).

DIMMER

Dims or brightens the display. The

brightness can be controlled in four steps.

DISPLAY

Switches the display of this unit. The

listening mode, sound volume, Pre Out

setting or input name can be checked by

selecting an input source.

1

6 Character display

See Display on page 11.

7 Tuner control buttons

BAND

Switches between AM, FM ST (stereo) and

FM MONO radio bands (page 48).

TUNE /

Used to find radio frequencies (page 48).

TUNER EDIT

Use with TUNE /, PRESET / and

ENTER to memorize and name stations for

recall (page 48, 49).

SPEAKERS

AUTO/DIRECT STEREO/ ALC STANDARD

LISTENING MODE

ADV SURROUND DIRECT CONTROL

iPod iPhone

DIMMER DISPLAY BAND TUNE TUNER EDIT PRESET ENTER

PHONES

INPUT

SELECTOR

STANDBY/ON

PHASE

CONTROL

MASTER

VOLUME

MCACC

SETUP MIC

AUDIO/ VIDEO MULTI-CHANNEL RECEIVER

VSX

-820

VIDEO INPUT

AUDIOLRVIDEO

iPod

iPhone

USB

1 27854 63

9

1110 141312

Note

1 The Pre Out setting may or may not be displayed, depending on the input source you have selected.

VSX-820_SYXCN_En.book 9 ページ２０１０年４月１２日　月曜日　午後６時５２分

Controls and displays02

10

En

PRESET /

Use to select preset radio stations

(page 49).

8

MASTER VOLUME

dial

9

PHONES

jack

Use to connect headphones. When the

headphones are connected, there is no sound

output from the speakers (page 41).

10 Listening mode buttons

AUTO/DIRECT

Switches between Auto surround mode

(Auto playback on page 33) and Stream

Direct playback. Stream Direct playback

bypasses the tone controls for the most

accurate reproduction of a source

(page 36).

STEREO/ALC

Switches between stereo playback, Auto

level control stereo mode (page 35) and

Front Stage Surround Advance modes

(page 35).

STANDARD

Press for Standard decoding and to switch

between the various 2 Pro Logic II, 2 Pro

Logic IIx, 2 Pro Logic IIz and NEO:6

options (page 32).

ADV SURROUND

Switches between the various surround

modes (page 34).

11

iPod iPhone DIRECT CONTROL

Change the receiver’s input to the iPod and

enable iPod operations on the iPod (page 68).

12

iPod iPhone/USB

terminal

Use to connect your Apple iPod or USB mass

storage device as an audio source (page 66

and page 69).

13

AUDIO/VIDEO

input

See Connecting to the front panel video terminal

on page 28.

14

MCACC SETUP MIC

jack

Use to connect a microphone when

performing Auto MCACC setup.

Operating range of remote control

The remote control may not work properly if:

• There are obstacles between the remote

control and the receiver’s remote sensor.

• Direct sunlight or fluorescent light is

shining onto the remote sensor.

• The receiver is located near a device that is

emitting infrared rays.

• The receiver is operated simultaneously

with another infrared remote control unit.

30°

7 m

30°

VSX-820_SYXCN_En.book 10 ページ２０１０年４月１２日　月曜日　午後６時５２分

Controls and displays 02

11

En

English

Français

Deutsch

Nederlands

Italiano

Español

Display

1PHASE

Lights when the Phase Control is switched on

(page 36).

2AUTO

Lights when the Auto Surround feature is

switched on (see Auto playback on page 33).

3RDS

Lights when an RDS broadcast is received

(page 50).

4ST

Lights when a stereo FM broadcast is being

received in auto stereo mode.

5TUNE

Lights when a normal broadcast channel is

being received.

6 Speaker indicators

Lights to indicate the current speaker system,

A and/or B (page 20).

7 Sleep timer indicator

Lights when the receiver is in sleep mode

(page 13).

8 Tuner preset indicators

PRESET

Shows when a preset radio station is

registered or called.

MEM

Blinks when a radio station is registered.

9 PRESET information or input signal

indicator

Shows the preset number of the tuner or the

input signal type, etc.

10 Character display

Displays various system information.

11 DTS indicators

DTS

Lights when a source with DTS encoded

audio signals is detected.

HD

Lights when a source with DTS-EXPRESS

or DTS-HD encoded audio signals is

detected.

ES

Lights to indicate DTS-ES decoding.

96/24

Lights when a source with DTS 96/24

encoded audio signals is detected.

NEO:6

When one of the NEO:6 modes of the

receiver is on, this lights to indicate NEO:6

processing (page 33).

12 Dolby Digital indicators

2D

Lights when a Dolby Digital encoded signal

is detected.

1 2 3 4 5 6 7 8

11 12 13 14 14 1615

9

10

VSX-820_SYXCN_En.book 11 ページ２０１０年４月１２日　月曜日　午後６時５２分

Controls and displays02

12

En

2D+

Lights when a source with Dolby Digital

Plus encoded audio signals is detected.

2HD

Lights when a source with Dolby TrueHD

encoded audio signals is detected.

EX

Lights to indicate Dolby Digital EX

decoding.

2PLll(x)

Lights to indicate 2 Pro Logic II / 2 Pro

Logic IIx decoding. Light will go off during

2 Pro Logic IIz decoding (see Listening in

surround sound on page 33 for more on

this).

13 ADV.S.

Lights when one of the Advanced Surround

modes has been selected (see Using the

Advanced surround effects on page 34 for more

on this).

14 SIGNAL SELECT indicators

DIGITAL

Lights when a digital audio signal is

selected.

Blinks when a digital audio signal is

selected and selected audio input is not

provided.

HDMI

Lights when an HDMI signal is selected.

Blinks when an HDMI signal is selected

and selected HDMI input is not provided.

15 Up Mix/DIMMER indicator

Lights when the Up Mix function is set to ON

(see page 37). Also, lights when DIMMER is set

to off.

16 DIR.

Lights when the DIRECT or PURE DIRECT

mode is switched on (page 36).

VSX-820_SYXCN_En.book 12 ページ２０１０年４月１２日　月曜日　午後６時５２分

Controls and displays 02

13

En

English

Français

Deutsch

Nederlands

Italiano

Español

Remote control

1

SLEEP

Press to change the amount of time before the

receiver switches into standby (30 min – 60

min – 90 min – Off). You can check the

remaining sleep time at any time by pressing

SLEEP once.

2

 RECEIVER

Switches the receiver between standby and on.

3

Switches the remote to control the receiver

(used to select the white commands above the

number buttons (MIDNIGHT, etc)). Also use

this button to set up surround sound (page 42)

or Audio parameters (page 38).

4

INPUT SELECT

Use to select the input source.

5

MULTI CONTROL

buttons

Press to select control of other components

(see

Controlling the rest of your system on

page 53

).

6

S.RETRIEVER

Press to restore CD quality sound to

compressed audio sources (page 36).

7

SIGNAL SEL

Use to select an input signal (page 41).

8 Listening mode buttons

AUTO/DIRECT

Switches between Auto surround mode

(Auto playback on page 33) and Stream

Direct playback. Stream Direct playback

bypasses the tone controls for the most

accurate reproduction of a source

(page 36).

STEREO/A.L.C.

Switches between stereo playback, Auto

level control stereo mode (page 35) and

Front Stage Surround Advance modes

(page 35).

STANDARD

Press for Standard decoding and to switch

between 2 Pro Logic II options (page 33).

ADV SURR

Switches between the various surround

modes (page 34).

Press BD first to access:

BD MENU*

Displays the disc menu of Blu-ray Discs.

BD DVD

INPUT SELECT

SOURCESLEEP

TV

CONTROL

DIMMER

TV

INPUT

1

4

7

MIDNIGHT

HDD

CH

RECEIVER

DVR CD

CD-R

ADAPTER iPod USB

VIDEO

TUNER

S.RETRIEVER

SIGNAL SEL

BD MENU

ENTER

STANDARD

ADV SURR

STEREO/

A.L.C.

AUTO/

DIRECT

VOL

+

10

2

5

8

SPEAKERS

LEV

SB CH

DISP

CLR

EQ

PHASE

DVD

3

6

9

0

ENTER

CH

CH SELECT

VCR

SHIFT

MUTE

RETURN

AUDIO

PARAMETER

TUNER EDIT

TOOLS

MASTER

VOLUME

iPod

CTRL

PTY SEARCH

BAND

MENU

HOME

MENU

SETUP

DTV/

TV

/

TRE

BASS

TOP

MENU

RECEIVER

T

U

N

E

T

U

N

E

P

R

E

S

E

T

P

R

E

S

E

T

RECEIVER

1

2

13

14

15

16

17

3

4

5

6

7

8

9

10

11

12

18

RECEIVER

VSX-820_SYXCN_En.book 13 ページ２０１０年４月１２日　月曜日　午後６時５２分

Controls and displays02

14

En

9 System Setup and component control

buttons

The following button controls can be accessed

after you have selected the corresponding

MULTI CONTROL button (BD, DVD, etc.).

Press first to access:

AUDIO PARAMETER

Use to access the Audio options (page 38).

SETUP

Press to access the System Setup menu

(page 42).

RETURN

Confirm and exit the current menu screen.

Press BD, DVD or DVR first to access:

TOP MENU

Displays the disc ‘top’ menu of a BD/DVD.

HOME MENU

Displays the HOME MENU screen.

RETURN

Confirm and exit the current menu screen.

MENU

Displays the TOOLS menu of Blu-ray Disc

player.

Press TUNER first to access:

TUNER EDIT

Memorizes/names stations for recall

(page 48 and 49).

BAND

Switches between AM, FM ST (stereo) and

FM MONO radio bands (page 48).

PTY SEARCH

Use to search for RDS program types

(page 50).

Press iPod USB first to access:

iPod CTRL

Switches between the iPod controls and

the receiver controls (page 68).

10



(

TUNE /

,

PRESET

/

),

ENTER

Use the arrow buttons when setting up your

surround sound system (page 42). Also used to

control BD/DVD menus/options.

Use the TUNE / buttons can be used to

find radio frequencies (page 48) and the

PRESET / buttons can be used to select

preset radio stations (page 49).

11 Component control buttons

The main buttons (, , etc.) are used to

control a component after you have selected it

using the input source buttons.

The controls above these buttons can be

accessed after you have selected the

corresponding input source button (BD, DVD,

DVR and CD). These buttons also function as

described below.

Press first to access:

BASS –/+

Use to adjust Bass

1

TRE –/+

Use to adjust Treble

1

Press TV first to access:

DTV/TV

Switches between the DTV and analog TV

input modes for Pioneer TVs.

12 Number buttons and other component

controls

Use the number buttons to directly select a

radio frequency (page 48) or the tracks on a

CD, etc. There are other buttons that can be

accessed after the button is

pressed. (For example MIDNIGHT, etc.)

HDD*, DVD*, VCR*

These buttons switch between the hard

disk, DVD and VCR controls for HDD/DVD/

VCR recorders.

RECEIVER

Note

1 The tone controls are disabled when the listening mode is set to DIRECT or PURE DIRECT.

RECEIVER

VSX-820_SYXCN_En.book 14 ページ２０１０年４月１２日　月曜日　午後６時５２分

Controls and displays 02

15

En

English

Français

Deutsch

Nederlands

Italiano

Español

SB CH

Press to select ON, AUTO, OFF the

surround back channel.

CH SELECT

Press repeatedly to select a channel, then

use LEV +/– to adjust the level (page 45).

LEV +/–

Use to adjust the channel level.

EQ

Press to switch on/off Acoustic Calibration

EQ setting (page 37).

MIDNIGHT

Switches to Midnight or Loudness

listening (page 39).

SPEAKERS

Use to change the speaker system

(page 20).

PHASE

Press to switch on/off Phase Control

(page 36).

DIMMER

Dims or brightens the display. The

brightness can be controlled in four steps.

13

 SOURCE

Press to turn on/off other components

connected to the receiver (see page 56 for

more on this).

14

TV CONTROL

buttons

These buttons are dedicated to control the TV

assigned to the TV button. Thus if you only

have one TV to hook up to this system assign it

to the TV button (see page 55 for more on this).



Use to turn on/off the power of the TV.

INPUT

Use to select the TV input signal.

CH +/–

Use to select channels.

VOL +/–

Use to adjust the volume on your TV.

15

MASTER VOLUME

+/–

Use to set the listening volume.

16

MUTE

Mutes/unmutes the sound.

17

DISP

Switches the display of this unit. The listening

mode, sound volume, Pre Out setting or input

name can be checked by selecting an input

source.

1

18

SHIFT

Press to access the ‘boxed’ commands (above

the buttons) on the remote. These buttons are

marked with an asterisk (* ) in this section.

Note

1 The Pre Out setting may or may not be displayed, depending on the input source you have selected.

VSX-820_SYXCN_En.book 15 ページ２０１０年４月１２日　月曜日　午後６時５２分

Connecting your equipment03

16

En

Chapter 3:

Connecting your equipment

Placing the speakers

By connecting the left and right front speakers (L/R), the center speaker (C), the left and right

surround speakers (SL/SR), and the subwoofer (SW), a 5.1 ch surround system can be enjoyed.

Further, by using an external amplifier, you can connect the left and right surround back speakers

(

SBL

/

SBR

) and the left and right front height speaker (

FHL

/

FHR

) to boost your system up to a 7.1 ch

surround system.

• You can also connect one surround back speaker (SB) and enjoy a 6.1 ch surround system.

To achieve the best possible surround sound, install your speakers as shown below.

a. This layout is available only when the additional amplifier is connected to the unit and the surround back

or front height speakers are connected to the amplifier. For details, see Connect the surround back or front height

speakers on page 19.

120

SL

L

SW

C

R

SR

120

SL

L

SW

C

R

SR

SB

120

SL

L

FHL

FHR

SW

C

R

SR

90

60

SL

L

SW

C

R

SR

SBL

SBR

5.1 channel surround system:

7.1 channel surround

(Surround back) system:

a

7.1 channel surround

(Front height) system:

a

6.1 channel surround

(Surround back) system:

a

VSX-820_SYXCN_En.book 16 ページ２０１０年４月１２日　月曜日　午後６時５２分

Connecting your equipment 03

17

En

English

Français

Deutsch

Nederlands

Italiano

Español

Hints on the speaker placement

Where you put your speakers in the room has a

big effect on the quality of the sound. The

following guidelines should help you to get the

best sound from your system.

• The subwoofer can be placed on the floor.

Ideally, the other speakers should be at

about ear-level when you’re listening to

them. Putting the speakers on the floor

(except the subwoofer), or mounting them

very high on a wall is not recommended.

• For the best stereo effect, place the front

speakers 2 m to 3 m apart, at equal

distance from the TV.

• If you’re going to place speakers around

your CRT TV, use shielded speakers or

place the speakers at a sufficient distance

from your CRT TV.

• If you’re using a center speaker, place the

front speakers at a wider angle. If not, place

them at a narrower angle.

• Place the center speaker above or below

the TV so that the sound of the center

channel is localized at the TV screen. Also,

make sure the center speaker does not

cross the line formed by the leading edge

of the front left and right speakers.

• It is best to angle the speakers towards the

listening position. The angle depends on

the size of the room. Use less of an angle

for bigger rooms.

• Surround and surround back speakers

should be positioned 60 cm to 90 cm

higher than your ears and titled slight

downward. Make sure the speakers don’t

face each other. For DVD-Audio, the

speakers should be more directly behind

the listener than for home theater

playback.

• If the surround speakers cannot be set

directly to the side of the listening position

with a 7.1-channel system, the surround

effect can be enhanced by turning off the

Up Mix function (see Setting the Up Mix

function on page 38).

• Try not to place the surround speakers

farther away from the listening position

than the front and center speakers. Doing

so can weaken the surround sound effect.

• Place the left and right front height

speakers at least one meter directly above

the left and right front speakers.

CAUTION

• Make sure that all speakers are securely

installed. This not only improves sound

quality, but also reduces the risk of

damage or injury resulting from speakers

being knocked over or falling in the event

of external shocks such as earthquakes.

Important

• To connect the surround back or front

height speakers, an additional amplifier is

required. Connect the additional amplifier

to the PRE OUT SURR BACK/FRONT

HEIGHT outputs of this unit and connect

the surround back or front height speakers

to the additional amplifier (see Connect

the surround back or front height speakers

on page 19).

The Pre Out setting must be set if the above

connections are performed. Select

SURR.BACK if the surround back speaker

is connected and HEIGHT if the front

height speaker is connected (If neither the

surround back speaker nor the front height

speaker is connected, either setting will

suffice) (see The Pre Out Setting on

page 47).

VSX-820_SYXCN_En.book 17 ページ２０１０年４月１２日　月曜日　午後６時５２分

Connecting your equipment03

18

En

Connecting the speakers

The receiver will work with just two stereo

speakers (the front speakers in the diagram)

but using at least three speakers is

recommended, and a complete setup is best

for surround sound.

Make sure you connect the speaker on the

right to the right (R) terminal and the speaker

on the left to the left (L) terminal. Also make

sure the positive and negative (+/–) terminals

on the receiver match those on the speakers.

You can use the speakers connected to the B

speaker terminals to listen to stereo playback

in another room. See Switching the speaker

system on page 20 for the listening options

with this setup.

You can use speakers with a normal

impedance between 6 Ω and 16 Ω.

However, note that only the front speakers are

set to a value between 12 Ω and 16 Ω if you

select SPAB in Switching the speaker system

on page 20.

Be sure to complete all connections before

connecting this unit to the AC power source.

AC IN

SURR BACK /

FRONT

HEIGHT

L

(

Single

)

R

L

IN

R

L

IN

OUT

IN

CD

TV/SAT

DVD BD

DVR/VCR

MONITOR OUT

P

R

P

B

Y

RL

DVD IN BD IN

OUT

MONITOR

COMPONENT VIDEO

TV/SAT

IN

DVR/VCR

OUT IN

FRONT

RL

CD-R/TAPE

DVR/VCR

CD-R/TAPE

PRE OUT

E

AUDIO

ADAPTER PORT

VIDEO

(

OUTPUT 5 V 100 mA MAX

)

(

BD

)

IN

1

(

DVD

)

IN

2

ASSIGNABLE

SPEAKERS

1

B

SPEAKERS

A

2

ANTENNA

FM

UNBAL

75

AM

LOOP

VOLTAGE SELECTOR

110-127 V 220-240 V

SUBWOOFER

PRE OUT

CENTER

SURROUND

RL

SW

L

C

RSLSR

LR

Center speaker

Surround speakers

Front speakers

Powered subwoofer

Speaker system B

VSX-820_SYXCN_En.book 18 ページ２０１０年４月１２日　月曜日　午後６時５２分

Connecting your equipment 03

19

En

English

Français

Deutsch

Nederlands

Italiano

Español

Bare wire connections

A-Speaker terminals:

1 Twist exposed wire strands together.

2 Loosen terminal and insert exposed wire.

3 Tighten terminal.

B-Speaker terminals:

1 Twist exposed wire strands together.

2 Push open the tabs and insert exposed

wire.

3 Release the tabs.

CAUTION

• These speaker terminals carry

HAZARDOUS LIVE voltage. To prevent

the risk of electric shock when connecting

or disconnecting the speaker cables,

disconnect the power cord before touching

any uninsulated parts.

• Make sure that all the bare speaker wire is

twisted together and inserted fully into the

speaker terminal. If any of the bare speaker

wire touches the back panel it may cause

the power to cut off as a safety measure.

Connect the surround back or front

height speakers

Connect the PRE OUT outputs of the unit and

additional amplifier to add a surround back or

front height speaker.

• If the surround back speaker or the front

height speaker is connected, set the Pre

Out setting (see The Pre Out Setting on

page 47).

• You can use the additional amplifier on the

surround back channel pre-outs for a

single speaker as well. In this case plug the

amplifier into the left (L (Single)) terminal

only.

123

10 mm

12 3

10 mm

IN BD

SURR BACK /

FRONT

HEIGHT

L

(

Single

)

R

L

IN

R

L

IN

OUT

IN

CD

TV/SAT

DVD BD

DVR/VCR

M

CD-R/TAPE

DVR/VCR

CD-R/TAPE

PRE OUT

DVD

TV/SAT

COAXIAL

OPTICAL

(

CD

)

IN

ASSIGNABLE

OUT

HDMI

DVR/VCR

1

(

CD-R/TAPE

)

IN

AUDIO

ADAPTER

(

OUTPUT 5 V 1

1

1 2

IN

2

SUBWOOFER

PRE OUT

ANTENNA

FM

UNBAL

75

AM

LOOP

INPUT

LR

ANALOG

SBL/FHL SBR/FHR

Surround back or

front height speakers

Surround back or

front height

channel amplifier

VSX-820_SYXCN_En.book 19 ページ２０１０年４月１２日　月曜日　午後６時５２分

Connecting your equipment03

20

En

Switching the speaker system

Three speaker system settings are possible

using the SPEAKERS button.

• Use the SPEAKERS button on the front

panel to select a speaker system setting.

1

Press repeatedly to choose a speaker system

option:

• SPA – Sound is output from the speakers

connected to the A speaker terminals and

PRE OUT SURR BACK/FRONT HEIGHT

(multichannel playback is possible).

• SPB – Sound is output from the two

speakers connected to speaker system B

(only stereo playback is possible).

• SPAB – Sound is output from speaker

system A, the two speakers in speaker

system B, and the subwoofer.

Multichannel sources are downmixed only

when the STEREO or ALC mode is selected

for stereo output from speaker systems A

and B.

2

• SP – No sound is output from the

speakers.

Making cable connections

Make sure not to bend the cables over the top

of this unit (as shown in the illustration). If this

happens, the magnetic field produced by the

transformers in this unit may cause a

humming noise from the speakers.

Important

• Before making or changing connections,

switch off the power and disconnect the

power cord from the AC outlet.

• Before unplugging the power cord, switch

the power into standby.

HDMI cables

Both video and sound signals can be transmitted

simultaneously with one cable.

If connecting the

player and the TV via this receiver, for both

connections, use HDMI cables.

3

Be careful to connect the terminal in the

proper direction.

Note

1 The subwoofer output depends on the settings you made in Speaker Setting on page 43. However, if SPB is selected above,

no sound is heard from the subwoofer (the LFE channel is not downmixed).

2 You can use speakers with a normal impedance between 6 Ω and 16 Ω. However, be aware that only the front speakers are set

to a value between 12 Ω and 16 Ω when you select SPAB.

SPEAKERS DIMMER DISPLAY

3 • Set the HDMI parameter in Setting the Audio options on page 38 to THRU (THROUGH) and set the input signal in Choosing

the input signal on page 41 to HDMI, if you want to hear HDMI audio output from your TV (no sound will be heard from this

receiver).

• If the video signal does not appear on your TV, try adjusting the resolution settings on your component or display. Note that

some components (such as video game units) have resolutions that may not be displayed. In this case, use a (analog)

composite connection.

• When the video signal from the HDMI is 480i, 480p, 576i or 576p, Multi Ch PCM sound and HD sound cannot be received.

HDMI cable

VSX-820_SYXCN_En.book 20 ページ２０１０年４月１２日　月曜日　午後６時５２分

La page charge ...

Pioneer VSX-820-S Silver Manuel utilisateur

Pioneer VSX-820-S Silver Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents