Pioneer SC-LX73 Le manuel du propriétaire

SC-LX83

SC-LX73

Quick Start Guide

Guide rapide

Kurzanleitung

SC-LX83_73_QuickGuideSY.book Page 1 Thursday, March 25, 2010 6:12 PM

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1_A1_En

D3-4-2-1-2-2*_A1_En

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified

service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug. Should

the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to

BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug

must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of

safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in

your plug, proceed as follows;

The wire which is coloured BLUE must be connected to the terminal which is marked with the

letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the

letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs

according to country or region. Be sure that the

power supply voltage of the area where this unit

will be used meets the required voltage (e.g., 230 V

or 120 V) written on the rear panel.

D3-4-2-1-4*_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

SC-LX83_73_QuickGuideSY.book Page 2 Thursday, March 25, 2010 6:12 PM

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Pb

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 20 cm at top, 10 cm at rear, and 20 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

If the AC plug of this unit does not match the AC

outlet you want to use, the plug must be removed

and appropriate one fitted. Replacement and

mounting of an AC plug on the power supply cord of

this unit should be performed only by qualified

service personnel. If connected to an AC outlet, the

cut-off plug can cause severe electrical shock. Make

sure it is properly disposed of after removal.

The equipment should be disconnected by removing

the mains plug from the wall socket when left unused

for a long period of time (for example, when on

vacation).

D3-4-2-2-1a_A1_En

CAUTION

The

STANDBY/ON

switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

SC-LX83_73_QuickGuideSY.book Page 3 Thursday, March 25, 2010 6:12 PM

4

En

Thank you for buying this pioneer product.

This Quick Start Guide includes instructions for basic

connections and operations to allow simple use of the

receiver. For detailed descriptions of the receiver, see the

“Operating Instructions” provided on the included CD-

ROM. The operating instructions can also be downloaded

from the Pioneer website (http://www.pioneer.eu).

See below for instructions on handling the CD-ROM.

Operating Environment

This CD-ROM can be used with Microsoft® Windows®

XP/Vista/7 and Apple Mac OS X 10.4.

Adobe Reader (Version 4.0 or later) is required to read

this CD-ROM.

Precautions For Use

This CD-ROM is for use with a personal computer. It

cannot be used with a DVD player or music CD player.

Attempting to play this CD-ROM with a DVD player or

music CD player can damage speakers or cause

impaired hearing due to the large volume.

License

Please agree to the “Terms of Use” indicated below

before using this CD-ROM. Do not use if you are

unwilling to consent to the terms of its use.

Terms of Use

Copyright to data provided on this CD-ROM belongs to

Pioneer Corporation. Unauthorized transfer, duplication,

broadcast, public transmission, translation, sales,

lending or other such matters that go beyond the scope

of “personal use” or “citation” as defined by Copyright

Law may be subject to punitive actions. Permission to

use this CD-ROM is granted under license by Pioneer

Corporation.

General Disclaimer

Pioneer Corporation does not guarantee the operation of

this CD-ROM with respect to personal computers using

any of the applicable OS. In addition, Pioneer

Corporation is not liable for any damages incurred as a

result of use of this CD-ROM and is not responsible for

any compensation. The names of private corporations,

products and other entities described herein are the

registered trademarks or trademarks of their respective

firms.

* When Using a Mac OS:

Place this CD-ROM in a CD drive and then double-click

on the CD-ROM icon to start up the application.

===============================================================

Contents

01 Before you start

Checking what’s in the box. . . . . . . . . . . . . . . . . . . . . . 6

Loading the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operating range of remote control unit for

infrared (IR) signal transmission . . . . . . . . . . . . . . . . . 7

Using the RF communications function

(SC-LX83 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Flow for operating the receiver with RF two-way

communications (SC-LX83 only) . . . . . . . . . . . . . . . . . . 8

Remote control (In case of SC-LX83). . . . . . . . . . . . . . . 8

Remote control (In case of SC-LX73). . . . . . . . . . . . . . 11

02 Connecting your equipment

Determining the speakers’ application . . . . . . . . . . . . 13

Placing the speakers . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting the speakers . . . . . . . . . . . . . . . . . . . . . . 15

Installing your speaker system . . . . . . . . . . . . . . . . . . 16

Selecting the Speaker system. . . . . . . . . . . . . . . . . . . 18

About the audio connection . . . . . . . . . . . . . . . . . . . . 18

About the video converter. . . . . . . . . . . . . . . . . . . . . . 18

About HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Connecting your TV and playback components . . . . . 20

Connecting an HDD/DVD recorder, BD recorder

and other video sources . . . . . . . . . . . . . . . . . . . . . . . 23

Connecting a satellite/cable receiver or other

set-top box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Connecting the multichannel analog inputs. . . . . . . . 25

Connecting other audio components . . . . . . . . . . . . . 26

Connecting AM/FM antennas. . . . . . . . . . . . . . . . . . . 27

MULTI-ZONE setup. . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Connecting to the network through

LAN interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Plugging in the receiver . . . . . . . . . . . . . . . . . . . . . . . 29

03 Basic Setup

Automatically conducting optimum sound tuning

(Full Auto MCACC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

04 Basic playback

Playing a source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Listening in surround sound. . . . . . . . . . . . . . . . . . . . 33

Using Auto surround, ALC, Optimum surround and

Stream Direct modes . . . . . . . . . . . . . . . . . . . . . . . . . 34

Playing an iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Playing a USB device . . . . . . . . . . . . . . . . . . . . . . . . . 36

Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . 36

Listening to Internet radio stations (SC-LX73 only) . . . 37

Playback with HOME MEDIA GALLERY inputs

(SC-LX83 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Bluetooth® ADAPTER for Wireless Enjoyment of

Music. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

SC-LX83_73_QuickGuideSY.book Page 4 Thursday, March 25, 2010 6:12 PM

5

En

Flow of settings on the receiver

The unit is a full-fledged AV receiver equipped with an abundance of functions and terminals. It can be used easily

after following the procedure below to make the connections and settings.

The colors of the steps indicate the following:

Required setting item (These items are included in this Quick Start Guide.)

Setting to be made as necessary (These items are explained in the “Operating Instructions” provided on the

included CD-ROM.)

1 Before you start

• Checking what’s in the box (page 6)

• Loading the batteries (page 6)



2

Determining the speakers’ application (page

13)

• 9.1 channel surround system (Front height)

• 9.1 channel surround system (Front wide)

• 7.1 channel surround system & Speaker B

connection

• 5.1 channel surround system & Front Bi-amping

connection (High quality surround)

• 5.1 channel surround system & ZONE 2 connection

(Multi Zone)



3 Connecting the speakers

• Placing the speakers (page 15)

• Connecting the speakers (page 15)

• Installing your speaker system (page 16)

• Bi-amping your speakers (page 17)



4 Connecting the components

• About the audio connection (page 18)

• About the video converter (page 18)

• Connecting your TV and playback components

(page 20)

• Connecting AM/FM antennas (page 27)

• Plugging in the receiver (page 29)



5Power On



6 Changing the OSD display language (OSD

Language)



7 MCACC speaker settings

• Automatically conducting optimum sound tuning

(Full Auto MCACC) (page 30)



8 The Input Setup menu

(When using connections other than the

recommended connections)



9 Basic playback (page 33)



10 Switching the HDMI output



11 Adjusting the sound and picture quality as desired

• Using the various listening modes

• Better sound using Phase Control

• Better sound using Phase Control and Full Band

Phase Control (SC-LX83 only)

• Measuring the all EQ type

(SYMMETRY/ALL CH ADJ/FRONT ALIGN)

• Changing the channel level while listening

• Switching on/off the Acoustic Calibration EQ,

Sound retriever or Dialog Enhancement

• Setting the PQLS function

• Setting the Audio options

(Tone, Loudness or Sound delay, etc.)

• Setting the Video options



12 Other optional adjustments and settings

• Control with HDMI function

• The Advanced MCACC menu

• The System Setup and Other Setup menus



13 Making maximum use of the remote control

SC-LX83:

• Operating multiple receivers

• Setting the remote to control other components

• Using the RF communications function

SC-LX73:

• Operating multiple receivers

• Setting the remote to control other components

SC-LX83_73_QuickGuideSY.book Page 5 Thursday, March 25, 2010 6:12 PM

Before you start

01

6

En

Chapter 1:

Before you start

Checking what’s in the box

Please check that you’ve received the following supplied

accessories:

In case of SC-LX83

• Setup microphone (cable: 5 m)

• Omni-directional remote control (CU-RF100)

•RF adapter

•IR blaster cable x2

• AA/LR6 dry cell batteries x4

• AM loop antenna

•FM wire antenna

• iPod cable

• Bluetooth ADAPTER (AS-BT100)

•Power cord

• Warranty card

• Operating instructions (CD-ROM)

• These quick start guide

In case of SC-LX73

• Setup microphone (cable: 5 m)

• Remote control unit

• AAA size IEC R03 dry cell batteries

(to confirm system operation) x2

• AM loop antenna

•FM wire antenna

• iPod cable

• Bluetooth ADAPTER (AS-BT100)

•Power cord

• Warranty card

• Operating instructions (CD-ROM)

• These quick start guide

Loading the batteries

In case of SC-LX83

In case of SC-LX73

The batteries included with the unit are to check initial

operations; they may not last over a long period.

We recommend using alkaline batteries that have a

longer life.

CAUTION

Incorrect use of batteries may result in such hazards as

leakage and bursting. Observe the following precautions:

• Never use new and old batteries together.

• Insert the plus and minus sides of the batteries

properly according to the marks in the battery case.

• Batteries with the same shape may have different

voltages. Do not use different batteries together.

• When disposing of used batteries, please comply

with governmental regulations or environmental

public instruction’s rules that apply in your country or

area.

• WARNING

Do not use or store batteries in direct sunlight or

other excessively hot place, such as inside a car or

near a heater. This can cause batteries to leak,

overheat, explode or catch fire. It can also reduce the

life or performance of batteries.

SC-LX83_73_QuickGuideSY.book Page 6 Thursday, March 25, 2010 6:12 PM

Before you start

01

7

En

Operating range of remote control unit

for infrared (IR) signal transmission

The remote control may not work properly if:

• There are obstacles between the remote control and

the receiver’s remote sensor.

• Direct sunlight or fluorescent light is shining onto the

remote sensor.

• The receiver is located near a device that is emitting

infrared rays.

• The receiver is operated simultaneously with another

infrared remote control unit.

Tip

• By connecting an RF adapter to the RS-232C and CU-

RF100 terminals (SC-LX83) / EXTENSION terminals

(SC-LX73), the CU-RF100 omni-directional remote

control can be used for RF two-way communications

with the receiver.

1

For details, see Using the RF

communications function (SC-LX83 only) below.

Using the RF communications function

(SC-LX83 only)

With RF two-way communications, the information of the

receiver’s display can be displayed on the remote control

in your hands and the remote control can be operated

without worrying about obstacles or the direction in

which the remote control is pointing.

2

For details, see

Flow for operating the receiver with RF two-way

communications (SC-LX83 only) on page 8.

Note

1 The RF adapter and CU-RF100 omni-directional remote control are included with the SC-LX83, sold separately with the SC-LX73.

7 m

30°

2 The maximum line-of-sight distance for RF two-way communications is about 10 meters. This line-of-sight communications distance is a rough

indication, and may differ according to the surrounding environment.

CONTROL

IN

OUT

RS-232C

Y

ANTENNA

FM UNBAL 75 AM LOOP

P

R

P

B

CU-RF100

I

R

IN

OU

T

1

2

(

OUTPUT 5 V

150 mA MAX

)

Remote control operation

RF Adapter

Receiver

Operation of the receiver or

other components placed in a

rack is possible

Operation is possible in any

direction the remote control is

pointed (360°)

SC-LX83_73_QuickGuideSY.book Page 7 Thursday, March 25, 2010 6:12 PM

Before you start

01

8

En

Flow for operating the receiver with RF

two-way communications

(SC-LX83 only)

This remote control unit is set for operations using

infrared signals upon shipment from the factory. To set it

for RF operations, take the steps below (See the

Operating Instructions in CD-ROM for detail).

Remote control (In case of SC-LX83)

This section explains how to operate the remote control

for the receiver.

1 Connecting the RF adapter to the RS-232C and CU-

RF100 terminals.

See Using the RF communications function (SC-

LX83 only) on page 7.



2

Setting the ‘

RF Remote Setup

’ to ‘ON’ with the

receiver.

1 Switch on the receiver.

2 Push gently on the lower third portion of the

receiver’s front panel, then press HOME MENU.

3 Use / to select System Setup

, then press

ENTER

.

4 Use / to select Other Setup

, then press

ENTER

.

5 Use / to select RF Remote Setup

, then press

ENTER

.

6 Use / to select ON

, then press

HOME

MENU

.



3 Pairing the RF adapter and remote control.

1 Press the SETTING button on the front of the RF

adapter.

RF adapter’s LED blinks red.

2 While pressing MULTI OPERATION, press

VIDEO PARAMETER on the remote control.

The remote display shows PAIRING.

3 Press ENTER on the remote control.

When pairing is successful, SUCCESS is displayed and

pairing is completed. RF adapter’s LED lights green.



4

Setting ‘RECEIVER MAIN’ to ‘

RF MODE

’ for the

remote control unit’s ‘

IR/RF SELECT

’ setting.

1 While pressing MULTI OPERATION, press

HOME MENU.

The remote display shows SETUP MENU.

2 Use / to select IR/RF SELECT, then press

ENTER.

3 Use / to select

RECEIVER MAIN

, then press

ENTER.

4 Use / to select RF MODE, then press

ENTER.

5 Press and hold MULTI OPERATION for a couple

of seconds

to exit and store the operation

.

DVD

RECEIVER SOURCE

MAIN

MULTI

OPERATION

AUDIO

PARAMETER

TOP MENU

BAND

iPod CTRL

PTY SEARCH

CATEGORY

LIST

TOOLS

HOME

MENU

STATUS

THX PQLSMPX MEMORY

PHASE CTRL CH LEVEL

T.EDIT

GUIDE

VIDEO

PARAMETER

ZONE2

SOURCE

TV

RECEIVER

3

iPod

USB

OPTION

MULTI CH

ADAPTER

NET RADIO

INPUT SELECT LIGHT

CD

PHONO

AUX

INPUT MUTE

TUNE

PRESET PRESET

MUTE

PGM MENU

VOL

TV CONTROL

CH

VIDEO

CD-R

STEREO

SIGNAL SEL SLEEP AUDIO

INFO

DIMMER

A.ATT

CLR

SBch MCACC

HDMI OUT

D.ACCESS

ENTER

CLASS

DISP

CH

AUTO/ALC/

DIRECT

STANDARD ADV SURR

IN

TUNER

HMG

BD

TV

HDMIDVR

BDR

12

ENTER

RETURN

1

2

3

4

7

8

9

10

5

6

11

12

13

14

SC-LX83_73_QuickGuideSY.book Page 8 Thursday, March 25, 2010 6:12 PM

Before you start

01

9

En

The remote has been conveniently color-coded according

to component control using the following system:

• White – Receiver control, TV control

• Blue – Other controls (see the Operating Instructions

in CD-ROM for detail)

1 MULTI-ZONE operation selector switch

Switch to perform operations in the main zone, ZONE 2

and ZONE 3.

2

 RECEIVER

This switches between standby and on for this receiver.

3

MULTI OPERATION

Use this button to perform multi operations.

4 Input function buttons

Press to select control of other components. There is no

AUX input on this receiver, so the AUX button cannot be

used.

5

INPUT SELECT

Use to select the input function.

6 Character display

This display shows information when transmitting

control signals. The remote screen’s display differs when

operating the receiver by sending infrared signals from

the remote control and when operating it by RF two-way

communications. For details, see Remote control display

on page 10.

7

TV CONTROL

buttons

These buttons are dedicated to control the TV assigned to

the TV operation selector switch.

8 Receiver setting buttons

Set the remote control operation selector switch to

RECEIVER first to access:

AUDIO PARAMETER – Use to access the Audio

options.

VIDEO PARAMETER – Use to access the Video

options.

HOME MENU – Use to access the Home Menu.

RETURN – Press to confirm and exit the current

menu screen.

9

///

/

ENTER

Use the arrow buttons when setting up your surround

sound system and the Audio or Video options.

10 Receiver Control buttons

Set the remote control operation selector switch to

RECEIVER first to access:

STATUS – Press to check selected receiver settings.

PHASE CTRL – Press to switch on/off Phase Control

or Full Band Phase Control.

CH LEVEL – Press repeatedly to select a channel,

then use / to adjust the level.

THX – Press to select a Home THX listening mode.

PQLS – Press to select the PQLS setting.

AUTO/ALC/DIRECT – Switches between Auto

Surround (page 34), Auto Level Control, Optimum

Surround mode and Stream Direct mode (page 34).

STEREO – Switches between stereo playback and

Front Stage Surround Advance modes.

STANDARD – Press for Standard decoding and to

switch various modes (2 Pro Logic, Neo:6, etc.)

(page 33).

ADV SURR – Use to switch between the various

surround modes (page 34).

SIGNAL SEL – Use to select an input signal.

SLEEP – Use to put the receiver in sleep mode and

select the amount of time before sleep.

DIMMER – Dims or brightens the display.

A.ATT – Attenuates (lowers) the level of an analog

input signal to prevent distortion.

SBch – With this receiver, SBch cannot be used.

MCACC – Press to switch between MCACC presets.

HDMI OUT – Switch the HDMI output terminal.

11

LIGHT

Press to turn on/off the illumination for the buttons.

1

12 Remote control operation selector switch

Set to RECEIVER to operate the receiver, TV or SOURCE

to operate the TV or the source device.

When this switch is set to RECEIVER, the receiver can be

controlled (used to select the white commands). Also use

this switch to set up surround sound.

13

VOL +/–

Use to set the listening volume.

14

MUTE

Mutes the sound or restores the sound if it has been

muted (adjusting the volume also restores the sound).

Note

1 Press and hold in the LIGHT button for 5 seconds to change the illumination mode 1 or 2. When set to LIGHT MODE 2 (default), the

illumination only lights when the remote control LIGHT button is pressed. When switched to LIGHT MODE 1, the illumination lights whenever

buttons are operated. Setting LIGHT MODE 1 will shorten the service life of the batteries.

SC-LX83_73_QuickGuideSY.book Page 9 Thursday, March 25, 2010 6:12 PM

Before you start

01

10

En

Remote control display

1

Remote control display for infrared signal

transmission (default)

Remote control display for RF two-way

communications

2

1 Remote control operating zone indicator

This indicates which zone the remote control is currently

set to operate. The display indicates the setting of the

MULTI-ZONE operation selector switch.

Only when RF two-way communications:

The box display here indicates the communication status

between this remote control unit and the receiver.

(White box with black letters): Two-way

communications are established and the receiver’s

power is on.

(Gray box with black letters): Two-way

communications are established and the receiver’s

power is off.

(White letters only): Two-way communications are

not working well. In this case, the area indicating the

receiver’s status (12) is not displayed.

2 Remote control code sending indicator

This appears when signals are sent from the remote

control.

3 Remote control code sending mode indicator

This indicates whether remote control codes are being

sent by infrared (IR) signal or RF communications.

4 Remote control operation indicator

This indicates which operation mode the remote control

is currently set to. The display indicates the setting of the

remote control operation selector switch.

5 Input function and sending code indicator

This indicates what input function can currently be

operated with the remote control. Also, when a button is

pressed and its operation code is sent, the name of that

code is displayed.

6 Area indicating the remote control's status

7 Nothing displayed

Nothing is displayed here when the remote control code

sending mode is set to IR.

8 Scroll indicators

Light when there are more selectable items when making

the various settings.

9 Receiver input indicator

This indicates the input function currently selected for

the receiver’s zone.

10 Receiver display

The same information as on the receiver’s display is

displayed here.

11 Master volume display

This indicates the volume of the receiver’s main zone

using, as an icon and in decibels (dB). When the sound

is muted, the icon is displayed.

12 Area indicating the receiver’s status

Note

1 The display lights when a remote control operation is performed, then turns off after 20 seconds if no other operation is performed. When in

the Remote Setup mode, the setup is canceled and the display turns off if no operation is performed for 1 minute.

2 • This is displayed when an RF adapter is connected to the receiver and paired with the remote control. For details, see Using the RF

communications function on the Operating Instructions in CD-ROM.

• Depending on the communications environment, two-way communications may not work well and the remote control display may not reflect

the receiver’s status.

MAIN SOURCEIR

iPod/USB

1 2 3 4

5

6

7

MAIN

VIDEO

RCV CTRLRF

AV RECEIVER

1. Adv MCACC

+12.0dB

1 2 3 4

56

89

10 11 12

MAIN

SC-LX83_73_QuickGuideSY.book Page 10 Thursday, March 25, 2010 6:12 PM

Before you start

01

11

En

Remote control (In case of SC-LX73)

This section explains how to operate the remote control

for the receiver.

The remote has been conveniently color-coded according

to component control using the following system:

• White – Receiver control, TV control

• Blue – Other controls (see the Operating Instructions

in CD-ROM for detail)

1  RECEIVER

This switches between standby and on for this receiver.

2

MULTI OPERATION – Use to perform multi

operations.

R.SETUP – Use to input the preset code when making

remote control settings and to set the remote control

mode.

3 Input function buttons

Press to select control of other components.

Use INPUT SELECT to select the input function.

4

TV CTRL

Set the preset code of your TV’s manufacturer when

controlling the TV.

5

TV CONTROL

buttons

These buttons are dedicated to control the TV assigned to

the TV CTRL button.

6 Receiver setting buttons

Press first to access:

AUDIO PARAMETER – Use to access the Audio

options.

VIDEO PARAMETER – Use to access the Video

options.

HOME MENU – Use to access the Home Menu.

RETURN – Press to confirm and exit the current

menu screen.

7

///

/

ENTER

Use the arrow buttons when setting up your surround

sound system and the Audio or Video options.

8 Receiver Control buttons

Press first to access:

AUTO/ALC/DIRECT –

Switches between Auto

Surround (

page 34

), Auto Level Control mode and

Stream Direct mode (

page 34

)

.

STEREO – Switches between stereo playback and

Front Stage Surround Advance modes.

STANDARD – Press for Standard decoding and to

switch various modes (2 Pro Logic, Neo:6, etc.)

(page 33).

ADV SURR – Use to switch between the various

surround modes (page 34).

THX – Press to select a Home THX listening mode.

PHASE CTRL – Press to switch on/off Phase Control.

STATUS – Press to check selected receiver settings.

PQLS – Press to select the PQLS setting.

HDMI OUT – Switch the HDMI output terminal.

SIGNAL SEL – Use to select an input signal.

MCACC – Press to switch between MCACC presets.

RECEIVER

ZONE 2 ZONE 3 LIGHT

AUTO

/

ALC

/

DIRECT

D.ACCESS

CH

LEVEL A.ATT DIMMER

SIGNAL SEL

MCACC SLEEP

HDMI OUT

TV

/

DTV MPX PQLS

PHASE

CTRL STATUSTHX

PGM

STEREO

iPod CTRL

HOME

MENU

TUNE

TOOLS

LIST

CH

TV CONTROL

INPUT

SELECT TV CTRL

iPod

USB TUNER VIDEO CD-R

ADAPTERNET RADIO

CDTV

BD DVD

R.SETUP

SOURCERECEIVER

MULTI

OPERATION

DVR/BDR HDMI

RECEIVER

MUTE

MASTER

VOLUME

VOL

PRESET

TOP MENU

BAND GUIDE

T.EDIT

VIDEO

PARAMETER

AUDIO

PARAMETER

ENTER

PRESET

RETURN

PTY

SEARCH

MEMORY

STANDARD

MENU

ADV SURR

AUDIO

INFO

CLASS

ENTER

DISP

HDD DVD

546

8

0

79

213

/

CLR

CH

1

2

3

4

8

9

5

6

7

10

11

12

13

14

RECEIVER

SC-LX83_73_QuickGuideSY.book Page 11 Thursday, March 25, 2010 6:12 PM

Before you start

01

12

En

SLEEP – Use to put the receiver in sleep mode and

select the amount of time before sleep.

CH LEVEL – Press repeatedly to select a channel,

then use / to adjust the level.

A.ATT – Attenuates (lowers) the level of an analog

input signal to prevent distortion.

DIMMER – Dims or brightens the display.

9

MULTI-ZONE

select buttons

Switch to perform operations in ZONE 2 and ZONE 3.

10 Remote control LED

Lights when a command is sent from the remote control.

11

Switches the remote to control the receiver (used to

select the white commands).

Switch to perform operations in the main zone.

Also use this button to set up surround sound.

12

MASTER VOLUME +/–

Use to set the listening volume.

13

MUTE

Mutes the sound or restores the sound if it has been

muted (adjusting the volume also restores the sound).

14

Press to turn on/off the illumination for the buttons. The

way the buttons light can be selected from four modes

(see the Operating Instructions in CD-ROM for detail).

RECEIVER

SC-LX83_73_QuickGuideSY.book Page 12 Thursday, March 25, 2010 6:12 PM

Connecting your equipment

02

13

En

Chapter 2:

Connecting your equipment

This receiver provides you with many connection

possibilities, but it doesn’t have to be difficult. This

chapter explains the kinds of components you can

connect to make up your home theater system.

Important

• Illustration shows the SC-LX83, however connections

for the SC-LX73 are the same except where noted.

CAUTION

• Before making or changing the connections, switch

off the power and disconnect the power cord from the

power outlet. Plugging in should be the final step.

Determining the speakers’ application

This unit permits you to build various surround systems,

in accordance with the number of speakers you have.

• Be sure to connect speakers to the front left and right

channels (L and R).

• It is also possible to only connect one of the surround

back speakers (SB) or neither.

Choose one from Plans [A] to [E] below.

[A] 9.1 channel surround system (Front height)

*Default setting

• Speaker System setting: Normal(SB/FH)

A 9.1 ch surround system connects the left and right

front speakers (L/R), the center speaker (C), the left and

right front height speakers (FHL/FHR), the left and right

surround speakers (SL/SR), the left and right surround

back speakers (SBL/SBR), and the subwoofer (SW).

This surround system produces a more true-to-life sound

from above.

[B] 9.1 channel surround system (Front wide)

• Speaker System

setting: Normal(SB/FW)

This plan replaces the left and right front height speakers

shown in [A] with the left and right front wide speakers

(FWL/FWR).

This surround system produces a true-to-life sound over

a wider area.

[C] 7.1 channel surround system & Speaker B

connection

• Speaker System setting: Speaker B

With these connections you can simultaneously enjoy

5.1-channel surround sound in the main zone with stereo

playback of the same sound on the B speakers. The same

connections also allow for 7.1-channel surround sound

in the main zone when not using the B speakers.

SL

L

FHL

SW

C

R

FHR

SR

SBL

SBR

FWR

FWL

SL

L

SW

C

R

SR

SBL

SBR

SL

L

SW

C

R

SR

SBL

SBR

L

R

Speaker B

SC-LX83_73_QuickGuideSY.book Page 13 Thursday, March 25, 2010 6:12 PM

Connecting your equipment

02

14

En

[D] 5.1 channel surround system & Front Bi-

amping connection (High quality surround)

• Speaker System setting: Front Bi-Amp

Bi-amping connection of the front speakers for high

sound quality with 5.1-channel surround sound.

[E] 5.1 channel surround system & ZONE 2

connection (Multi Zone)

• Speaker System setting: ZONE 2

With these connections you can simultaneously enjoy

5.1-channel surround sound in the main zone with stereo

playback on another component in ZONE 2. (The

selection of input devices is limited.)

Important

•The Speaker System setting must be made if you

use any of the connections shown above other than

[A] (see Speaker system setting on Operating

Instructions in CD-ROM).

• Sound does not come through simultaneously from

the front height, front wide, speaker B and surround

back speakers. Output speakers are different

depending on the input signal or listening mode.

Other speaker connections

• Your favorite speaker connections can be selected

even if you have fewer than 5.1 speakers (except front

left/right speakers).

• When not connecting a subwoofer, connect speakers

with low frequency reproduction capabilities to the

front channel. (The subwoofer’s low frequency

component is played from the front speakers, so the

speakers could be damaged.)

•

After connecting, be sure to conduct the Full Auto

MCACC (speaker environment setting) procedure.

See Automatically conducting optimum sound tuning

(Full Auto MCACC) on page 30.

L

R

SL

SW

C

SR

Front Bi-Amp

L

R

SL

SW

C

SR

Main zone

Sub zone

ZONE 2

SC-LX83_73_QuickGuideSY.book Page 14 Thursday, March 25, 2010 6:12 PM

Connecting your equipment

02

15

En

Placing the speakers

Refer to the chart below for placement of the speakers

you intend to connect.

• Place the surround speakers at 120º from the center.

If you, (1) use the surround back speaker, and, (2)

don’t use the front height speakers / front wide

speakers, we recommend placing the surround

speaker right beside you.

• If you intend to connect only one surround back

speaker, place it directly behind you.

• Place the left and right front height speakers at least

one meter directly above the left and right front

speakers.

Connecting the speakers

Each speaker connection on the receiver comprises a

positive (+) and negative (–) terminal. Make sure to

match these up with the terminals on the speakers

themselves.

CAUTION

• These speaker terminals carry HAZARDOUS LIVE

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Make sure that all the bare speaker wire is twisted

together and inserted fully into the speaker terminal.

If any of the bare speaker wire touches the back panel

it may cause the power to cut off as a safety measure.

Bare wire connections

1 Twist exposed wire strands together.

(fig. A)

2 Loosen terminal and insert exposed wire.

(fig. B)

3 Tighten terminal.

(fig. C)

Important

• Please refer to the manual that came with your

speakers for details on how to connect the other end

of the speaker cables to your speakers.

• Use an RCA cable to connect the subwoofer. It is not

possible to connect using speaker cables.

CAUTION

• Make sure that all speakers are securely installed.

This not only improves sound quality, but also

reduces the risk of damage or injury resulting from

speakers being knocked over or falling in the event of

external shocks such as earthquakes.

L

SW

C

FHL

FWL

SL

SBL

SBR

SB

SR

FWR

R

FHR

30 30

60

120 120

fig. A fig. B fig. C

10 mm

SC-LX83_73_QuickGuideSY.book Page 15 Thursday, March 25, 2010 6:12 PM

Connecting your equipment

02

16

En

Installing your speaker system

At the very least, front left and right speakers only are necessary. Note that your main surround speakers should always

be connected as a pair, but you can connect just one surround back speaker if you like (it must be connected to the

left surround back terminal).

Standard surround connection

RS-232C

HDMI

ASSIGNABLE

COAXIAL

COMPONENT VIDEO

ASSIGNABLE

OPTICAL

ASSIGNABLEASSIGNABLE

MONITOR OUT

ZONE 2 OUT

IN

Y

CD-R/TAPE

ANTENNA

FM UNBAL 75 AM LOOP

AC IN

IN

CD

IN

VIDEO

MONITOR

OUT

ZONE2

OUT

ZONE3

OUT

DVD

IN

TV/SAT

IN

VIDEO

IN

DVR/BDR PHONO

IN

OUT IN

P

R

P

B

1

INBD

IN

1

IN

2

IN

3

OUT 1

(

CONTROL

)

OUT 2

1 4

(

DVD

)

IN

2

(

DVR/BDR

)

IN

3

(

VIDEO

)

IN

1

(

DVD

)

IN

1

(

TV/SAT

)

IN

2

(

DVR/BDR

)

IN

OUT

FRONT CENTER SURROUND SURR BACK

(Single)

FH/FW

3

(

VIDEO

)

IN

2

(

CD

)

IN

3

(

CD-R

)

CONTROL

CU-RF100

IR 12 V

TRIGGER

IN

OUT

1

2

1

2

(OUTPUT

12 V

TOTAL

150 mA MAX)

SUBWOOFER

IN

4

LAN

(

10/100

)

(

OUTPUT 5 V

100 mA MAX

)

ADAPTER PORT

PRE OUT

(

OUTPUT 5 V

150 mA MAX

)

SPEAKERS

MULTI CH IN

SIGNAL

GND

FRONT CENTER

SUBWOOFER

SURROUND SURR BACK

L

R

CAUTION:

SPEAKER IMPEDANCE 6 Ω - 16 Ω .

ATTENTION:

ENCEINTE D'IMPEDANCE DE 6 Ω - 16 Ω .

A

SURROUND BACK

(Single)

B

R

FRONT HEIGHT/WIDE/

LR L R L R L

SURROUND FRONT CENTER

SEE INSTRUCTION

MANUAL

SELECTABLE

VOIR LE MODE

D'EMPLOI

SELECTABLE

LINE LEVEL

INPUT

Front left

Subwoofer

Center

Surround right

Not connectedNot connected

Front right

Surround left

The surround back terminals can also be

used for ZONE 2.

5.1 ch surround setting

Surround back

Not connected

Surround back left

ZONE 2 setting

ZONE 2 - Right

ZONE 2 - Left

6.1 ch surround setting

Surround back right

7.1 ch surround setting

Speaker B - leftSpeaker B - right

Speaker B setting

Front wide left

Front wide right

Front height left

Front height setting

Front height right

The front height terminals can also be used

for the front wide and Speaker B speakers.

Front wide setting

SC-LX83_73_QuickGuideSY.book Page 16 Thursday, March 25, 2010 6:12 PM

Connecting your equipment

02

17

En

Bi-amping your speakers

Bi-amping is when you connect the high frequency driver

and low frequency driver of your speakers to different

amplifiers for better crossover performance. Your

speakers must be bi-ampable to do this (having separate

terminals for high and low) and the sound improvement

will depend on the kind of speakers you’re using.

CAUTION

• Most speakers with both High and Low terminals

have two metal plates that connect the High to the

Low terminals. These must be removed when you are

bi-amping the speakers or you could severely

damage the amplifier. See your speaker manual for

more information.

• If your speakers have a removable crossover network,

make sure you do not remove it for bi-amping. Doing

so may damage your speakers.

Bi-wiring your speakers

Your speakers can also be bi-wired if they support bi-

amping.

• With these connections, the Speaker System setting

makes no difference.

• To bi-wire a speaker, connect two speaker cords to

the speaker terminal on the receiver.

CAUTION

• Don’t connect different speakers from the same

terminal in this way.

• When bi-wiring as well, heed the cautions for bi-

amping shown at the left.

RS-232C

HDMI

ASSIGNABLE

COAXIAL

COMPONENT VIDEO

ASSIGNABLE

OPTICAL

ASSIGNABLEASSIGNABLE

MONITOR OUT

ZONE 2 OUT

IN

Y

CD-R/TAPE

ANTENNA

FM UNBAL 75 AM LOOP

AC IN

IN

CD

IN

VIDEO

MONITOR

OUT

ZONE2

OUT

ZONE3

OUT

DVD

IN

TV/SAT

IN

VIDEO

IN

DVR/BDR PHONO

IN

OUT IN

P

R

P

B

1

INBD

IN

1

IN

2

IN

3

OUT 1

(

CONTROL

)

OUT 2

1 4

(

DVD

)

IN

2

(

DVR/BDR

)

IN

3

(

VIDEO

)

IN

1

(

DVD

)

IN

1

(

TV/SAT

)

IN

2

(

DVR/BDR

)

IN

OUT

FRONT CENTER SURROUND SURR BACK

(Single)

FH/FW

3

(

VIDEO

)

IN

2

(

CD

)

IN

3

(

CD-R

)

CONTROL

CU-RF100

IR 12 V

TRIGGER

IN

OUT

1

2

1

2

(OUTPUT

12 V

TOTAL

150 mA MAX)

SUBWOOFER

IN

4

LAN

(

10/100

)

(

OUTPUT 5 V

100 mA MAX

)

ADAPTER PORT

PRE OUT

(

OUTPUT 5 V

150 mA MAX

)

SPEAKERS

MULTI CH IN

SIGNAL

GND

FRONT CENTER

SUBWOOFER

SURROUND SURR BACK

L

R

CAUTION:

SPEAKER IMPEDANCE 6 Ω - 16 Ω .

ATTENTION:

ENCEINTE D'IMPEDANCE DE 6 Ω - 16 Ω .

A

SURROUND BACK

(Single)

B

R

FRONT HEIGHT/WIDE/

L RLRLRL

SURROUND FRONT CENTER

SEE INSTRUCTION

MANUAL

SELECTABLE

VOIR LE MODE

D'EMPLOI

SELECTABLE

High

Low

High

Low

Front left

Subwoofer

Center

Surround right

Front right

Surround left

Bi-amp compatible

speaker

Bi-amp compatible

speaker

SC-LX83_73_QuickGuideSY.book Page 17 Thursday, March 25, 2010 6:12 PM

Connecting your equipment

02

18

En

Selecting the Speaker system

The front height terminals can be used for front wide and

Speaker B connections, in addition to for the front height

speakers. Also, the surround back terminals can be used

for bi-amping and ZONE 2 connections, in addition to for

the surround back speakers. Make this setting according

to the application.

Front height setup

*Default setting

1 Connect a pair of speakers to the front height

speaker terminals.

See Standard surround connection on page 16.

2 If necessary, select ‘

Normal(SB/FH)

’ from the

Speaker System

menu.

See Speaker system setting on Operating Instructions in

CD-ROM to do this.

Front wide setup

1 Connect a pair of speakers to the front height

speaker terminals.

See Standard surround connection on page 16.

2 Select ‘

Normal(SB/FW)

’ from the

Speaker System

menu.

See Speaker system setting on Operating Instructions in

CD-ROM to do this.

Speaker B setup

You can listen to stereo playback in another room.

1 Connect a pair of speakers to the front height

speaker terminals.

See Standard surround connection on page 16.

2 Select ‘

Speaker B

’ from the

Speaker System

menu.

See Speaker system setting on Operating Instructions in

CD-ROM to do this.

Bi-Amping setup

Bi-amping connection of the front speakers for high

sound quality with 5.1-channel surround sound.

1 Connect bi-amp compatible speakers to the front

and surround back speaker terminals.

See Bi-amping your speakers on page 17.

2 Select ‘

Front Bi-Amp

’ from the

Speaker System

menu.

See Speaker system setting on Operating Instructions in

CD-ROM to do this.

ZONE 2 setup

With these connections you can simultaneously enjoy

5.1-channel surround sound in the main zone with stereo

playback on another component in ZONE 2.

1 Connect a pair of speakers to the surround back

speaker terminals.

See Standard surround connection on page 16.

2 Select ‘

ZONE 2

’ from the

Speaker System

menu.

See Speaker system setting on Operating Instructions in

CD-ROM to do this.

About the

audio connection

• With an HDMI cable, video and audio signals can be

transferred in high quality over a single cable.

About the video converter

The video converter ensures that all video sources are

output through all of the MONITOR VIDEO OUT jacks.

The only exception is HDMI: since this resolution cannot

be downsampled, you must connect your monitor/TV to

the receiver’s HDMI video outputs when connecting this

video source.

1

Types of cables and

terminals

Transferable audio

signals

Sound signal priority 

HDMI HD audio

Digital (Coaxial) Conventional digital audio

Digital (Optical)

RCA (Analog)

(White/Red)

Conventional analog audio

Note

1 • If the video signal does not appear on your TV, try adjusting the resolution settings on your component or display. Note that some

components (such as video game units) have resolutions that may not be converted. In this case, try switching Digital Video Conversion (in

Setting the Video options on Operating Instructions in CD-ROM) OFF.

• The signal input resolutions that can be converted from the component video input for the HDMI output are 480i/576i, 480p/576p, 720p and

1080i. 1080p signals cannot be converted.

• Only signals with an input resolution of 480i/576i can be converted from the component video input for the composite MONITOR OUT

terminals.

SC-LX83_73_QuickGuideSY.book Page 18 Thursday, March 25, 2010 6:12 PM

Connecting your equipment

02

19

En

If several video components are assigned to the same

input function (see The Input Setup menu on Operating

Instructions in CD-ROM), the converter gives priority to

HDMI, component, then composite (in that order).

• For optimal video performance, THX recommends

switching Digital Video Conversion (in Setting the

Video options on Operating Instructions in CD-ROM)

OFF.

About HDMI

1

The HDMI connection transfers uncompressed digital

video, as well as almost every kind of digital audio.

This receiver incorporates High-Definition Multimedia

Interface (HDMI

®

) technology.

This receiver supports the functions described below

through HDMI connections.

2

• Digital transfer of uncompressed video (contents

protected by HDCP (1080p/24, 1080p/60, etc.))

• 3D signal transfer

3

• Deep Color signal transfer

3

• x.v.Color signal transfer

3

• Audio Return Channel

3

• Input of multi-channel linear PCM digital audio

signals (192 kHz or less) for up to 8 channels

• Input of the following digital audio formats:

4

– Dolby Digital, Dolby Digital Plus, DTS, High bitrate

audio (Dolby TrueHD, DTS-HD Master Audio, DTS-

HD High Resolution Audio), DVD-Audio, CD, SACD

(DSD signal), Video CD, Super VCD

• Synchronized operation with components using the

Control with HDMI function (see Control with HDMI

function on Operating Instructions in CD-ROM).

HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing, LLC in the United States and other countries.

“x.v.Color” and x.v.Color logo are trademarks of Sony

Corporation.

VIDEO IN

VIDEO

MONITOR OUT

COMPONENT

VIDEO IN

Y

P

B

P

R

YP

B

P

R

COMPONENT VIDEO

MONITOR OUT

HDMI IN HDMI OUT

High picture quality

Terminal for connection

with source device

Terminal for connection

with TV monitor

Video signals can be output

This product incorporates copyright protection technology that is

protected by U.S. patents and other intellectual property rights.

Use of this copyright protection technology must be authorized by

Rovi Corporation, and is intended for home and other limited

viewing uses only unless otherwise authorized by Rovi

Corporation. Reverse engineering or disassembly is prohibited.

Note

1 • An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High Bandwidth Digital Content

Protection (HDCP). If you choose to connect to a DVI connector, you will need a separate adaptor (DVIHDMI) to do so. A DVI connection,

however, does not support audio signals. Consult your local audio dealer for more information.

• If you connect a component that is not compatible with HDCP, an HDCP ERROR message is displayed on the front panel display. Some

components that are compatible with HDCP still cause this message to be displayed, but so long as there is no problem with displaying video

this is not a malfunction.

• Depending on the component you have connected, using a DVI connection may result in unreliable signal transfers.

• This receiver supports SACD, Dolby Digital Plus, Dolby TrueHD and DTS-HD Master Audio. To take advantage of these formats, however,

make sure that the component connected to this receiver also supports the corresponding format.

2 • Use a High Speed HDMI

®

cable. If an HDMI cable other than a High Speed HDMI

®

cable is used, it may not work properly.

• When an HDMI cable with a built-in equalizer is connected, it may not operate properly.

3 Signal transfer is only possible when connected to a compatible component.

4 • HDMI format digital audio transmissions require a longer time to be recognized. Due to this, interruption in the audio may occur when

switching between audio formats or beginning playback.

• Turning on/off the device connected to this unit's HDMI OUT terminal during playback, or disconnecting/connecting the HDMI cable during

playback, may cause noise or interrupted audio.

SC-LX83_73_QuickGuideSY.book Page 19 Thursday, March 25, 2010 6:12 PM

Connecting your equipment

02

20

En

Connecting your TV and playback components

Connecting using HDMI

If you have an HDMI or DVI (with HDCP) equipped component (Blu-ray disc player (BD), etc.), you can connect it to

this receiver using a commercially available HDMI cable.

If the TV and playback components support the Control with HDMI feature, the convenient Control with HDMI

functions can be used (see Control with HDMI function on Operating Instructions in CD-ROM).

• When connecting to an HDMI/DVI-compatible

monitor using the HDMI OUT 2 terminal, switch the

HDMI output setting to HDMI OUT 2 or HDMI OUT

ALL. See Switching the HDMI output on Operating

Instructions in CD-ROM.

• For input components, connections other than HDMI

connections are also possible (see Connecting your

DVD player with no HDMI output on page 21).

• If you want to listen to the sound of the TV over the

receiver, connect the receiver and TV with audio

cables.

1

RS-232C

HDMI

ASSIGNABLE

COAXIAL

COMPONENT VIDEO

ASSIGNABLE

OPTICAL

ASSIGNABLEASSIGNABLE

MONITOR OUT

ZONE 2 OUT

IN

Y

CD-R/TAPE

ANTENNA

FM UNBAL 75 AM LOOP

IN

CD

IN

VIDEO

MONITOR

OUT

ZONE2

OUT

ZONE3

OUT

DVD

IN

TV/SAT

IN

VIDEO

IN

DVR/BDR PHONO

IN

OUT IN

P

R

P

B

1

INBD

IN

1

IN

2

IN

3

OUT 1

(

CONTROL

)

OUT 2

1 4

(

DVD

)

IN

2

(

DVR/BDR

)

IN

3

(

VIDEO

)

IN

1

(

DVD

)

IN

1

(

TV/SAT

)

IN

2

(

DVR/BDR

)

IN

O

FRONT CENTER SURROUND SURR BACK

(Single)

FH/FW

3

(

VIDEO

)

IN

2

(

CD

)

IN

3

(

CD-R

)

CONTROL

CU-RF100

IR 12 V

TRIGGER

IN

OUT

1

2

1

2

(OUTPUT

12 V

TOTAL

150 mA MAX)

SUBWOOFER

IN

4

LAN

(

10/100

)

(

OUTPUT 5 V

100 mA MAX

)

ADAPTER PORT

PRE OUT

(

OUTPUT 5 V

150 mA MAX

)

SPEAKERS

SIGNAL

GND

FRONT CE

N

SUB

W

CAUTION:

SPEAKER IMPEDANCE 6 Ω - 16 Ω .

ATTENTION:

ENCEINTE D'IMPEDANCE DE 6 Ω - 16 Ω .

SURROUND BACK

(Single)

B

R

FRONT HEIGHT/WIDE/

LR L R L

SURROUND

SEE INSTRUCTION

MANUAL

SELECTABLE

VOIR LE MODE

D'EMPLOI

SELECTABLE

DIGITAL OUT

COAXIAL OPTICAL

ANALOG

RL

AUDIO OUT

HDMI INHDMI OUTHDMI OUT

Other HDMI/DVI-

equipped component

HDMI/DVI-compatible

Blu-ray disc player

HDMI/DVI-compatible

monitor

Select one

This connection is

required in order to

listen to the sound of

the TV over the

receiver.

1

Note

1 When the TV and receiver are connected by HDMI connections, if the TV supports the HDMI Audio Return Channel function, the sound of the

TV is input to the receiver via the HDMI terminal, so there is no need to connect an audio cable. In this case, set TV Audio at HDMI Setup to

via HDMI (see HDMI Setup on Operating Instructions in CD-ROM).

SC-LX83_73_QuickGuideSY.book Page 20 Thursday, March 25, 2010 6:12 PM

La page est en cours de chargement...

Pioneer SC-LX73 Le manuel du propriétaire

Pioneer SC-LX73 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents