Pioneer VSX-324-K-P Manuel utilisateur

Register your product on

http://www.pioneerelectronics.com (US)

http://www.pioneerelectronics.ca (Canada)

http://www.pioneerelectronics.com (États-unis)

http://www.pioneerelectronics.ca (Canada)

•

Protect your new investment

The details of your purchase will be on file for reference in the event of an

insurance claim such as loss or theft.

•

Improve product development

Your input helps us continue to design products that meet your needs.

•

Receive a free Pioneer newsletter

Registered customers can opt in to receive a monthly newsletter.

•

Receive free tips, updates and service bulletins on

your new product

Home Theater Package

Ensemble de Cinéma Maison

Paquete de Home Theater

HTP-072

AV Receiver

Récepteur AV

Receptor AV

VSX-324-K-P

Operating Instructions

Mode d’emploi

Manual de instrucciones

VSX-324-K-P_CMXESM.book 1 ページ２０１３年２月１３日　水曜日　午前９時１７分

2

En

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

CAUTION:

TO PREVENT THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT

D3-4-2-1-1b_A1_En

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

D8-10-1-2_A1_En

Information to User

Alterations or modifications carried out without appropriate authorization may invalidate the user’s right to operate

the equipment.

D8-10-2_A1_En

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 20 cm at top, 10 cm at rear, and 10 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

Caution

To prevent fire hazard, the Class 2 Wiring Cable

should be used for connection with speaker, and

should be routed away from hazards to avoid damage

to the insulation of the cable.

D3-7-13-67*_A1_En

Anki

XXX

VSX-324-K-P_CMXESM.book 2 ページ２０１３年２月１３日　水曜日　午前９時１７分

3

En

English

Français

Español

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s

instructions.

Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong. The wide blade or the third

prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

1)

2)

3)

4)

5)

6)

7)

8)

9)

10)

Only use attachments/accessories specified by

the manufacturer.

Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

Unplug this apparatus during lightning storms

or when unused for long periods of time.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

D3-7-13-69_En

11)

12)

13)

14)

CAUTION

The STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

These symbols are only valid

in the European Union.

K058c_A1_En

(Symbol examples for batteries)

Pb

This Class B digital apparatus complies with

Canadian ICES-003.

D8-10-1-3_A1_En

CAUTION

This product satisfies FCC regulations when shielded

cables and connectors are used to connect the unit

to other equipment. To prevent electromagnetic

interference with electric appliances such as radios

and televisions, use shielded cables and connectors

for connections.

D8-10-3a_A1_En

IMPORTANT NOTICE

THE MODEL NUMBER AND SERIAL NUMBER OF

THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.

RECORD THESE NUMBERS ON YOUR ENCLOSED

WARRANTY CARD AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

D36-AP9-1_A1_En

WARNING: Handling the cord on this product or

cords associated with accessories sold with the

product may expose you to chemicals listed on

proposition 65 known to the State of California and

other governmental entities to cause cancer and

birth defect or other reproductive harm.

D36-P5_B1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

WARNING

Store small parts out of the reach of children and

infants. If accidentally swallowed, contact a doctor

immediately.

D41-6-4_A1_En

VSX-324-K-P_CMXESM.book 3 ページ２０１３年２月１３日　水曜日　午前９時１７分

4

En

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you

have finished reading the instructions, put them away in a safe place for future reference.

Contents

Before you start

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Checking what’s in the box . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Flow of settings on the receiver

. . . . . . . . . . . . . . 5

01 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Loading the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operating range of remote control . . . . . . . . . . . . . . . . . 9

02 Connecting your equipment

Placing the speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Hints on the speaker placement. . . . . . . . . . . . . . . . . . 10

Connecting the speakers. . . . . . . . . . . . . . . . . . . . . . . . . 11

Making cable connections . . . . . . . . . . . . . . . . . . . . . . . 12

HDMI cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

About HDMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Analog audio cables. . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Digital audio cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Standard RCA video cables . . . . . . . . . . . . . . . . . . . . . 13

About video outputs connection . . . . . . . . . . . . . . . . . . . 13

Connecting a TV and playback components . . . . . . . . . . 14

Connecting using HDMI . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting your component with no HDMI terminal . . 15

Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using external antennas . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting an iPod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting a USB device . . . . . . . . . . . . . . . . . . . . . . . . 17

Plugging in the receiver . . . . . . . . . . . . . . . . . . . . . . . . . 17

03 Basic playback

Playing a source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Selecting the audio input signal . . . . . . . . . . . . . . . . . 18

Playing an iPod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Playing back files stored on an iPod . . . . . . . . . . . . . . 20

Basic playback controls. . . . . . . . . . . . . . . . . . . . . . . . 20

Switches between the iPod controls and the receiver

controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Playing a USB device . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Basic playback controls. . . . . . . . . . . . . . . . . . . . . . . . 21

Compressed audio compatibility . . . . . . . . . . . . . . . . . 21

Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Improving FM sound . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Saving station presets . . . . . . . . . . . . . . . . . . . . . . . . . 22

Listening to station presets . . . . . . . . . . . . . . . . . . . . . 22

Naming preset stations . . . . . . . . . . . . . . . . . . . . . . . . 22

04 Listening to your system

Choosing the listening mode . . . . . . . . . . . . . . . . . . . . . 23

Auto playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Listening in surround sound . . . . . . . . . . . . . . . . . . . . 23

Using the Advanced surround . . . . . . . . . . . . . . . . . . 23

Using Stream Direct . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Using the Sound Retriever . . . . . . . . . . . . . . . . . . . . . . . 24

Better sound using Phase Control . . . . . . . . . . . . . . . . . 24

Setting the Audio options . . . . . . . . . . . . . . . . . . . . . . . . 25

05 Home menu

Using the Home menu . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Manual speaker setup . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Speaker Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

X.Over . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Channel Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Speaker Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

The Input Assign menu. . . . . . . . . . . . . . . . . . . . . . . . . . 29

The Auto Power Down menu . . . . . . . . . . . . . . . . . . . . . 29

The HDMI Setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . 30

06 Additional information

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Important information regarding the HDMI

connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

iPod messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

USB messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

About iPod/iPhone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Resetting the main unit . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

VSX-324-K-P_CMXESM.book 4 ページ２０１３年２月１３日　水曜日　午前９時１７分

5

En

English

Français

Español

Before you start

Checking what’s in the box

Please check that you’ve received the following supplied

accessories:

• Remote control

• AAA size IEC R03 dry cell batteries (to confirm system

operation) x2

• AM loop antenna

• FM wire antenna

•SPEAKER CAUTION Sheet (English only)

• These operating instructions

Installing the receiver

• When installing this unit, make sure to put it on a level

and stable surface.

Don’t install it on the following places:

– on a color TV (the screen may distort)

– near a cassette deck (or close to a device that gives off a

magnetic field). This may interfere with the sound.

– in direct sunlight

– in damp or wet areas

– in extremely hot or cold areas

– in places where there is vibration or other movement

– in places that are very dusty

– in places that have hot fumes or oils (such as a kitchen)

Flow of settings on the

receiver

The unit is a full-fledged AV receiver equipped with an

abundance of functions and terminals. It can be used easily

after following the procedure below to make the connections

and settings.

The colors of the steps indicate the following:

Required setting item

Setting to be made as necessary

1

Connecting the speakers

Where you place the speakers will have a big effect on the

sound.

• Placing the speakers (page 10)

• Connecting the speakers (page 11)



2

Connecting the components

For surround sound, you’ll want to hook up using a digital

connection from the Blu-ray Disc/DVD player to the

receiver.

• About video outputs connection (page 13)

• Connecting a TV and playback components (page 14)

• Connecting antennas (page 16)

• Plugging in the receiver (page 17)



3

Power On

Make sure you’ve set the video input on your TV to this

receiver. Check the manual that came with the TV if you

don’t know how to do this.



4

The Input Assign menu (page 29)

(When using connections other than the recommended

connections.)

The HDMI Setup menu (page 30)

(When the connected TV supports the HDMI Audio

Return Channel function.)



5

Basic playback (page 18)

• Selecting the audio input signal (page 18)

• Playing an iPod (page 19)

• Playing a USB device (page 20)

• Choosing the listening mode (page 23)



6

Adjusting the sound as desired

• Using the Sound Retriever (page 24)

• Better sound using Phase Control (page 24)

• Setting the Audio options (page 25)

• Manual speaker setup (page 27)

VSX-324-K-P_CMXESM.book 5 ページ２０１３年２月１３日　水曜日　午前９時１７分

01

Controls and displays

6

En

Chapter 1:

Controls and displays

Front panel

1 INPUT SELECTOR dial

Selects an input source (page 18).

2 Receiver control buttons

SPEAKERS – Use to change the speaker system on or off.

When the SP OFF is selected, no sound is output from the

speakers connected to this receiver.

DIMMER – Dims or brightens the display. The brightness

can be controlled in four steps.

DISPLAY – Switches the display of this unit. The listening

mode, sound volume, input name can be checked by

selecting an input source.

3 Character display

See Display on page 7.

4 Tuner control buttons

BAND – Switches between AM, FM ST (stereo) and FM

MONO radio bands (page 21).

TUNER EDIT – Use with TUNE /, PRESET / and

ENTER to memorize and name stations for recall

(page 21).

TUNE / – Used to find radio frequencies (page 21).

PRESET / – Use to select preset radio stations

(page 22).

5 Remote sensor

Receives the signals from the remote control (see Operating

range of remote control on page 9).

6 HDMI indicator

Blinks when connecting an HDMI-equipped component;

lights when the component is connected (page 14).

7 iPod iPhone indicator

Lights when an iPod/iPhone is connected and iPod/USB

input is selected (page 19).

8 MASTER VOLUME dial

9

 STANDBY/ON

10 PHONES jack

Use to connect headphones. When the headphones are

connected, there is no sound output from the speakers. The

listening mode when the sound is heard from the headphone

can be selected only from PHONES SURR, STEREO or

STEREO ALC mode.

11 Listening mode buttons

AUTO SURROUND/STREAM DIRECT – Switches

between Auto surround mode (page 23) and Stream

Direct playback (page 24).

ALC/STANDARD SURR – Press for standard decoding

and to switch between the modes of 2 Pro Logic and

NEO:6, and the Auto level control stereo mode (page 23).

ADVANCED SURROUND – Switches between the

various surround modes (page 23).

AV RECEIVER

MASTER

VOLUME

5V 1A

STANDBY/ ON

INPUT

SELECTOR

ECO

iPod iPhone

DIRECT CONTROL

ADVANCED

SURROUND

PHONES

SPEAKERS DIMMER DISPLAY BAND TUNER EDIT TUNE PRESET ENTER

iPod iPhone

VSX

-324

HDMI

ALC/

STANDARD SURR

AUTO SURROUND

/

STREAM DIRECT

1 34

9 10 1312 1411

6

7285

15 16 17 18 19 17

22 23 24 25 25 26

20

21

VSX-324-K-P_CMXESM.book 6 ページ２０１３年２月１３日　水曜日　午前９時１７分

01

Controls and displays

7

En

English

Français

Español

12 ECO

Switches between ECO Mode 1/ECO Mode 2. When ECO

Mode is turned ON, the display will go dark

(page 23).

13 iPod iPhone DIRECT CONTROL

Change the receiver’s input to the iPod and enable iPod

operations on the iPod

(page 20).

14

iPod/iPhone

terminal

Use to connect your Apple iPod or USB mass storage

device as an audio source

(page 16).

Display

15 PHASE

Lights when the Phase Control is switched on (page 24).

16 AUTO

Lights when the Auto Surround feature is switched on

(page 23).

17 Tuner indicators

ST – Lights when a stereo FM broadcast is being received

in auto stereo mode (page 21).

TUNE – Lights when a normal broadcast channel.

PRESET – Shows when a preset radio station is registered

or called.

MEM – Blinks when a radio station is registered.

kHz/MHz – Lights when the character display is showing

the currently received AM/FM broadcast frequency.

18 Speaker indicators

Shows if the speaker system is on or not (page 6).

SPA means the speakers are switched on.

SP means the speakers are switched off.

19 Sleep timer indicator

Lights when the receiver is in sleep mode (page 8).

20 PRESET information or input signal indicator

Shows the preset number of the tuner or the input signal

type, etc.

21 Character display

Displays various system information.

22 DTS indicators

DTS – Lights when a source with DTS encoded audio

signals is detected.

HD – Lights when a source with DTS-EXPRESS or DTS-

HD encoded audio signals is detected.

96/24 – Lights when a source with DTS 96/24 encoded

audio signals is detected.

NEO:6 – When one of the NEO:6 modes of the receiver is

on, this lights to indicate NEO:6 processing (page 23).

23 Dolby Digital indicators

2D – Lights when a Dolby Digital encoded signal is

detected.

2D+ – Lights when a source with Dolby Digital Plus

encoded audio signals is detected.

2HD – Lights when a source with Dolby TrueHD

encoded audio signals is detected.

2PLII – Lights to indicate 2 Pro Logic II decoding (see

Listening in surround sound on page 23 for more on this).

24 ADV.S.

Lights when one of the Advanced Surround modes has been

selected (see Using the Advanced surround on page 23 for

more on this).

25 SIGNAL SELECT indicators

DIGITAL – Lights when a digital audio signal is selected.

Blinks when a digital audio signal is selected and

selected audio input is not provided.

HDMI – Lights when an HDMI signal is selected. Blinks

when an HDMI signal is selected and selected HDMI

input is not provided.

26 DIR.

Lights when the DIRECT or PURE DIRECT mode is switched

on (page 24).

VSX-324-K-P_CMXESM.book 7 ページ２０１３年２月１３日　水曜日　午前９時１７分

01

Controls and displays

8

En

Remote control

As for operating other devices, the remote control codes for

the Pioneer products are preset. The settings cannot be

changed.

1 SLEEP

Press to change the amount of time before the receiver

switches into standby (30 min – 60 min – 90 min – Off). You

can check the remaining sleep time at any time by pressing

SLEEP once.

2

 RECEIVER

Switches the receiver between standby and on.

3

Switches the remote to control the receiver (used to select

the white commands above the number buttons

(MIDNIGHT, etc)). Also use this button to set up surround

sound (page 27) or Audio parameters (page 25).

4 INPUT SELECT

Use to select the input source (page 18).

5 Input function buttons

Use to select the input source to this receiver (page 18). This

will enable you to control other Pioneer components with the

remote control.

6 SIGNAL SEL

Press to select the audio input signal of the component

to play back

(page 18).

7 Sound control buttons

Acous.EQ – Cannot use for this unit.

S.RETRIEVER – Press to restore CD quality sound to

compressed audio sources (page 24).

PHASE – Press to switch on/off Phase Control (page 24).

8 Listening mode and component control buttons

AUTO/DIRECT – Switches between Auto surround mode

(page 23) and Stream Direct playback (page 24).

STEREO – Press to select stereo playback (page 23).

ALC/STANDARD – Press for standard decoding and to

switch between the modes of 2 Pro Logic II and NEO:6,

and the Auto level control stereo mode (page 23).

ADV SURR – Switches between the various surround

modes (page 23).

ECO –

Switches between ECO Mode 1/ECO Mode 2.

When ECO Mode is turned ON, the display will go

dark

(page 23).

9 Receiver and component control buttons

The following button controls can be accessed after you have

selected the corresponding input function button (BD, DVD,

etc.).

Press first to access:

AUDIO PARAMETER – Use to access the Audio options

(page 25).

HOME MENU – Press to access the Home Menu

(page 27).

RETURN – Confirm and exit the current menu screen.

Press BD, DVD first to access:

TOP MENU – Displays the disc ‘top’ menu of a Blu-ray

Disc/DVD.

HOME MENU – Displays the HOME MENU screen.

RETURN – Confirm and exit the current menu screen.

MENU – Displays the TOOLS menu of Blu-ray Disc player.

Press TUNER first to access:

TOOLS – Memorizes stations for recall, also used to

change the name (page 22).

BAND – Switches between AM, FM ST (stereo) and FM

MONO radio bands (page 21).

Press iPod/USB first to access:

iPod CTRL – Switches between the iPod controls and the

receiver controls (page 20).

10

///

(TUNE

/

, PRESET

/

), ENTER

Use the arrow buttons when setting up your surround sound

system (page 27). Also used to control Blu-ray Disc/DVD

menus/options.

Use TUNE / can be used to find radio frequencies and

PRESET / can be used to select preset radio stations

(page 22).

BD DVD

INPUT SELECT

SOURCESLEEP

TV

CONTROL

DIMMER

CD

INPUT

1

4

7

MIDNIGHT

CH

RECEIVER

TUNER

iPod/USB

SAT/CBL

GAME

TV

SIGNAL SEL

Acous.EQ

PHASE

S.RETRIEVER

ENTER

ADV SURR

ECO

AUTO/

DIRECT

VOL

+

10

2

5

8

SPEAKERS

LEV

SB CH

DISP

CLR

3

6

9

0

ENTER

CH

CH SELECT

MUTE

RETURN

AUDIO

PARAMETER

TOOLS

MENU

VOLUME

BAND

HOME

MENU

iPod CTRL

PTY

TRE

BASS

TOP

MENU

RECEIVER

T

U

N

E

T

U

N

E

P

R

E

S

E

T

P

R

E

S

E

T

RECEIVER

ALC/

STANDARD

STEREO

1

2

13

14

15

16

17

3

4

6

5

7

8

9

10

12

11

RECEIVER

VSX-324-K-P_CMXESM.book 8 ページ２０１３年２月１３日　水曜日　午前９時１７分

01

Controls and displays

9

En

English

Français

Español

11 Component control buttons

The main buttons (, , etc.) are used to control a

component after you have selected it using the input function

buttons.

The controls above these buttons can be accessed after you

have selected the corresponding input function button (BD,

DVD and CD). These buttons also function as described

below.

Press first to access:

BASS –/+, TRE –/+ – Use to adjust Bass or Treble.

• These controls are disabled when the listening mode is

set to DIRECT or PURE DIRECT.

• When the front speaker is set at SMALL in the Speaker

Setting and the X.over is set above 150 Hz, the

subwoofer channel level will be adjusted by pressing

BASS –/+ (page 28).

12 Number buttons and other component controls

Use the number buttons to directly select a radio frequency

(page 21) or the tracks on a CD, etc. There are other buttons

that can be accessed after is pressed. (For

example MIDNIGHT, etc.)

SB CH– Cannot use for this unit.

CH SELECT – Press repeatedly to select a channel, then

use LEV +/– to adjust the level (page 28).

LEV +/– – Use to adjust the channel level.

MIDNIGHT – Switches to Midnight or Loudness listening

(page 25).

SPEAKERS – Use to change the speaker system on or off.

When the SP OFF is selected, no sound is output from the

speakers connected to this receiver.

DIMMER – Dims or brightens the display. The brightness

can be controlled in four steps.

13

 SOURCE

Turns on or off the power of the Pioneer DVD/DVR units when

BD, DVD or CD is selected using the input function buttons.

14 TV CONTROL buttons

These buttons can control only be used with Pioneer TVs.

 – Use to turn on/off the power of the TV.

INPUT – Use to select the TV input signal.

CH +/– – Use to select channels.

VOL +/– – Use to adjust the volume on your TV.

15 VOLUME +/–

Use to set the listening volume.

16 MUTE

Mutes/unmutes the sound.

17 DISP

Switches the display of this unit. The listening mode, sound

volume or input name can be checked by selecting an input

source.

Loading the batteries

The batteries included with the unit are to check initial

operations; they may not last over a long period. We

recommend using alkaline batteries that have a longer life.

CAUTION

• Incorrect use of batteries may result in such hazards as

leakage and bursting. Observe the following precautions:

-

Never use new and old batteries together.

-

Insert the plus and minus sides of the batteries properly

according to the marks in the battery case.

-

Batteries with the same shape may have different

voltages. Do not use different batteries together.

-

When disposing of used batteries, please comply with

governmental regulations or environmental public

institution

’s rules that apply in your country/area.

-

When inserting the batteries, make sure not to damage the

springs on the battery’s (–) terminals. This can cause

batteries to leak or overheat.

WARNING

Do not use or store batteries in direct sunlight or other

excessively hot place, such as inside a car or near a

heater. This can cause batteries to leak, overheat, explode

or catch fire. It can also reduce the life or performance of

batteries.

Operating range of remote control

The remote control may not work properly if:

• There are obstacles between the remote control and the

receiver’s remote sensor.

• Direct sunlight or fluorescent light is shining onto the

remote sensor.

• The receiver is located near a device that is emitting

infrared rays.

• The receiver is operated simultaneously with another

infrared remote control unit.

RECEIVER

30°

7 m (23 ft.)

30°

VSX-324-K-P_CMXESM.book 9 ページ２０１３年２月１３日　水曜日　午前９時１７分

02

Connecting your equipment

10

En

Chapter 2:

Connecting your equipment

Placing the speakers

By connecting the left and right front speakers (

L

/

R

), the center speaker (

C

), the left and right

surround speakers (

SL

/

SR

), and the subwoofer (

SW

), a 5.1 ch surround system can be enjoyed.

To achieve the best possible surround sound, install your speakers as shown below.

Hints on the speaker placement

Where you put your speakers in the room has a big effect on the quality of the sound. The

following guidelines should help you to get the best sound from your system.

• The subwoofer can be placed on the floor. Ideally, the other speakers should be at about

ear-level when you’re listening to them. Putting the speakers on the floor (except the

subwoofer), or mounting them very high on a wall is not recommended.

• Speakers installed to the right and left should be separated by about 1.8 m to 2.7 m (6 ft.

to 8.9 ft.) distance. They should be installed at equal distances from the television, and at

equal heights from the floor.

• If you’re going to place speakers around your CRT TV, place the speakers at a sufficient

distance from your CRT TV.

• If you’re using a center speaker, place the front speakers at a wider angle. If not, place

them at a narrower angle.

• Place the center speaker above or below the TV so that the sound of the center channel is

localized at the TV screen. Also, make sure the center speaker does not cross the line

formed by the leading edge of the front left and right speakers.

• It is best to angle the speakers towards the listening position. The angle depends on the

size of the room. Use less of an angle for bigger rooms.

• Surround speakers should be positioned 60 cm to 90 cm (2 ft. to 3 ft.) higher than your ears

and titled slight downward. Make sure the speakers don’t face each other. For DVD-Audio,

the speakers should be more directly behind the listener than for home theater playback.

• Try not to place the surround speakers farther away from the listening position than the

front and center speakers. Doing so can weaken the surround sound effect.

CAUTION

• Make sure that all speakers are securely installed. This not only improves sound quality,

but also reduces the risk of damage or injury resulting from speakers being knocked over

or falling in the event of external shocks such as earthquakes.

120

SL

L

SW

C

R

SR

5.1 channel surround system:

VSX-324-K-P_CMXESM.book 10 ページ２０１３年２月１３日　水曜日　午前９時１７分

02

Connecting your equipment

11

En

English

Français

Español

Connecting the speakers

The receiver will work with just two stereo speakers (the front speakers in the diagram) but

using at least three speakers is recommended, and a complete setup is best for surround

sound.

Make sure you connect the speaker on the right to the right (R) terminal and the speaker on

the left to the left (L) terminal. Also make sure the positive and negative (+/–) terminals on the

receiver match those on the speakers.

You can use speakers with a nominal impedance between 6



and 16



.

Be sure to complete all connections before connecting this unit to the AC power source.

Bare wire connections

CAUTION

• These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of electric

shock when connecting or disconnecting the speaker cables, disconnect the power cord

before touching any uninsulated parts.

• Make sure that all the bare speaker wire is inserted fully into the speaker terminal. If any

of the bare speaker wire touches the back panel it may cause the power to cut off as a

safety measure.

1 Push open the tabs and insert exposed

wire.

2 Release the tabs.

12

HDMI

VIDEO AUDIO

COAXIAL

SPEAKERS

ANTENNA

OPTICAL

ASSIGNABLEASSIGNABLE

ASSIGNABLE

OUTIN IN

A

(

CD

)

MONITOR

OUT

DVD IN

ANALOG IN

(CD)

SAT/CBL

IN

DVD SAT/CBL GAME BD

(

TV

)

IN

1

IN

1

FM UNBAL

75

AM LOOP

FRONT CENTER

SURROUND SUBWOOFER

RLRL

RL

Center

Surround right

Front right

Front left

Subwoofer

Surround left

VSX-324-K-P_CMXESM.book 11 ページ２０１３年２月１３日　水曜日　午前９時１７分

02

Connecting your equipment

12

En

Making cable connections

Make sure not to bend the cables over the top of this unit (as

shown in the illustration). If this happens, the magnetic field

produced by the transformers in this unit may cause a

humming noise from the speakers.

Important

• Before making or changing connections, switch off the

power and disconnect the power cord from the AC outlet.

• Before unplugging the power cord, switch the power into

standby.

HDMI cables

Both video and sound signals can be transmitted

simultaneously with one cable. If connecting the player and

the TV via this receiver, for both connections, use HDMI

cables.

Be careful to connect the terminal in the proper direction.

Note

• Set the HDMI parameter in Setting the Audio options on

page 25 to THRU (THROUGH) and set the input signal in

Selecting the audio input signal on page 18 to HDMI, if you

want to hear HDMI audio output from your TV (no sound

will be heard from this receiver).

• If the video signal does not appear on your TV, try

adjusting the resolution settings on your component or

display. Note that some components (such as video game

units) have resolutions that may not be displayed. In this

case, use a (analog) composite connection.

• When the video signal from the HDMI is 480i, 480p, 576i

or 576p, Multi Ch PCM sound and HD sound cannot be

received.

About HDMI

The HDMI connection transfers uncompressed digital video,

as well as almost every kind of digital audio that the

connected component is compatible with, including DVD-

Video, DVD-Audio, SACD, Dolby Digital Plus, Dolby TrueHD,

DTS-HD Master Audio (see below for limitations), Video CD/

Super VCD and CD.

This receiver incorporates High-Definition Multimedia

Interface (HDMI

®

) technology.

This receiver supports the functions described below through

HDMI connections.

• Digital transfer of uncompressed video (contents

protected by HDCP (1080p/24, 1080p/60, etc.))

•3D signal transfer

• Deep Color signal transfer

• x.v.Color signal transfer

• Audio Return Channel (see The HDMI Setup menu on

page 30)

• Input of multi-channel linear PCM digital audio signals

(192 kHz or less) for up to 8 channels

• Input of the following digital audio formats:

– Dolby Digital, Dolby Digital Plus, DTS, High bitrate

audio (Dolby TrueHD, DTS-HD Master Audio), DVD-

Audio, CD, SACD (DSD 2 ch only), Video CD, Super VCD.

• 4K signal transfer

–This may not operate properly, depending on the

connected equipment.

– 4K 24p, 4K 25p and 4K 30p signals are supported.

Note

• Use a High Speed HDMI

®/

™ Cable. If HDMI cable other

than a High Speed HDMI

®/

™ Cable is used, it may not

work properly.

• When an HDMI cable with a built-in equalizer is

connected, it may not operate properly.

• 3D, Deep Color, x.v.Color, 4K signal transfer and Audio

Return Channel are only possible when connected to a

compatible component.

• HDMI format digital audio transmissions require a longer

time to be recognized. Due to this, interruption in the

audio may occur when switching between audio formats

or beginning playback.

• Turning on/off the device connected to this unit’s HDMI

OUT terminal during playback, or disconnecting/

connecting the HDMI cable during playback, may cause

noise or interrupted audio.

The terms HDMI and HDMI High-Definition Multimedia

Interface, and the HDMI Logo are trademarks or registered

trademarks of HDMI Licensing, LLC in the United States and

other countries.

“x.v.Color” and are trademarks of Sony

Corporation.

HDMI

®

VSX-324-K-P_CMXESM.book 12 ページ２０１３年２月１３日　水曜日　午前９時１７分

02

Connecting your equipment

13

En

English

Français

Español

Analog audio cables

Use stereo RCA phono cables to connect analog audio

components. These cables are typically red and white, and

you should connect the red plugs to R (right) terminals and

white plugs to L (left) terminals.

Digital audio cables

Commercially available coaxial digital audio cables or optical

cables should be used to connect digital components to this

receiver.

Note

• When connecting optical cables, be careful when

inserting the plug not to damage the shutter protecting

the optical socket.

• When storing optical cable, coil loosely. The cable may be

damaged if bent around sharp corners.

• You can also use a standard RCA video cable for coaxial

digital connections.

Standard RCA video cables

These cables are the most common type of video connection

and are used to connect to the composite video terminals.

The yellow plugs distinguish them from cables for audio.

About video outputs connection

This receiver is not loaded with a video converter. When you

use HDMI cables for connecting to the input device, the

same cables should be used for connecting to the TV.

The signals input from the analog (composite) video inputs of

this unit will not be output from the HDMI OUT.

L

R

AUDIO

White (Left)

Red (Right)

COAXIAL

IN

OPTICAL

IN

Coaxial digital

audio cable

Optical cable

VIDEO

Yellow

VIDEO

IN

HDMI

MONITOR

OUT

HDMI

OUT

Terminal for connection with

source device

Terminal for connection

with TV monitor

Playback component

TV

Video signals can be output.

The OSD will

not appear.

VSX-324-K-P_CMXESM.book 13 ページ２０１３年２月１３日　水曜日　午前９時１７分

02

Connecting your equipment

14

En

Connecting a TV and playback components

Connecting using HDMI

If you have an HDMI or DVI (with HDCP) equipped component (Blu-ray Disc player, etc.), you

can connect it to this receiver using a commercially available HDMI cable.

• The following connection/setting is required to listen to the sound of the TV over this

receiver.

-

If the TV does not support the HDMI Audio Return Channel function, Connect the receiver

and TV with audio cables (as shown).

-

If the TV supports the HDMI Audio Return Channel function, the sound of the TV is input

to the receiver via the HDMI terminal, so there is no need to connect an audio cable. In

this case, set ARC at HDMI Setup to ON (see The HDMI Setup menu on page 30).

Important

• If the receiver is connected to a TV using an HDMI cable, the on-screen display (OSD) will

not be displayed. Be sure to use a standard RCA analog video cable to connect. In this

case, switch the TV input to analog to see the OSD screen (for setup, etc.) on the TV.

• When the ARC function is ON and the receiver is connected to a compatible TV with an

HDMI cable, and you switch the input of the TV to composite, the input of the receiver may

automatically switch to TV. If this happens, switch the receiver’s input back to the original

input, or turn OFF the ARC function (see The HDMI Setup menu on page 30).

Note

• In order to listen to the audio from the TV that is connected to this receiver using an analog

audio cables, set-up for analog audio input is required (see The Input Assign menu on

page 29).

HDMI

VIDEO AUDIO

COAXIAL

SPEAKERS

ANTENNA

OPTICAL

ASSIGNABLEASSIGNABLE

ASSIGNABLE

OUTIN IN

A

(

CD

)

MONITOR

OUT

DVD IN

ANALOG IN

(CD)

SAT/CBL

IN

DVD SAT/CBL GAME BD

(

TV

)

IN

1

IN

1

FM UNBAL

75

AM LOOP

FRONT CENTER

SURROUN

D

RLRL

RL

HDMI IN

HDMI OUT HDMI OUT HDMI OUT

RL

DIGITAL AUDIO OUTANALOG AUDIO OUT

OPTICAL

VIDEO IN

Select one

DVD player,

HDD/DVD recorder

Set-top box

Game console

Blu-ray Disc player,

Blu-ray Disc recorder

HDMI/DVI-compatible TV

This connection is

necessary in order to

see the OSD of the

unit on the TV.

HDMI/DVI-compatible components

If the TV does not support

the HDMI Audio Return

Channel function, this

connection is required to

listen to the TV sound

over the receiver.

VSX-324-K-P_CMXESM.book 14 ページ２０１３年２月１３日　水曜日　午前９時１７分

02

Connecting your equipment

15

En

English

Français

Español

Connecting your component with no HDMI terminal

This diagram shows connections of a TV and DVD player (or other playback component) with

no HDMI terminal to the receiver.

Note

• In order to listen to the audio from the TV that is connected to this receiver using a analog

audio cables, set-up for analog audio input is required (see The Input Assign menu on

page 29).

• You can only connect one component to the optical input terminal. If connecting other

devices, please use a different method to connect the audio.

In order to listen to the audio from the source component that is connected to this receiver

using an optical cable, first, switch to the DVD (DVD player) or SAT/CBL (set-top box), then

press SIGNAL SEL to choose the audio signal O1 (OPTICAL1) (see Selecting the audio input

signal on page 18).

• You can only connect one component to the coaxial input terminal. If connecting other

devices, please use a different method to connect the audio. In order to listen to the audio

from the source component that is connected to this receiver using a coaxial cable, first,

switch to the DVD (DVD player) or SAT/CBL (set-top box), then press SIGNAL SEL to

choose the audio signal C1 (COAXIAL1) (see Selecting the audio input signal on page 18).

In order to listen to the audio from the DVD player that is connected to this receiver using

a coaxial cable, first, switch to the DVD input, then press SIGNAL SEL to choose the audio

signal C1 (COAXIAL1) (see Selecting the audio input signal on page 18).

HDMI

VIDEO AUDIO

COAXIAL

SPEAKERS

ANTENNA

OPTICAL

ASSIGNABLEASSIGNABLE

ASSIGNABLE

OUTIN IN

A

(

CD

)

MONITOR

OUT

DVD IN

ANALOG IN

(CD)

SAT/CBL

IN

DVD SAT/CBL GAME BD

(

TV

)

IN

1

IN

1

FM UNBAL

75

AM LOOP

FRONT CENTER

SURROUND

RLRL

RL

OPTICAL

RL

DIGITAL AUDIO OUTANALOG AUDIO OUT

OPTICAL

RL

DIGITAL AUDIO OUTANALOG AUDIO OUT

COAXIAL

VIDEO IN

VIDEO OUT

RL

DIGITAL AUDIO OUTANALOG AUDIO OUT

OPTICAL

COAXIAL

VIDEO OUT

Select one

TV

DVD player

This connection is

required in order to

listen to the sound of

the TV over the

receiver.

Select one

Set-top box

Select one

VSX-324-K-P_CMXESM.book 15 ページ２０１３年２月１３日　水曜日　午前９時１７分

02

Connecting your equipment

16

En

Connecting antennas

Connect the AM loop antenna and the FM wire antenna as

shown below. To improve reception and sound quality,

connect external antennas (see Using external antennas

below).

1 Push open the tabs, then insert one wire fully into each

terminal, then release the tabs to secure the AM antenna

wires.

2 Fix the AM loop antenna to the attached stand.

To fix the stand to the antenna, bend in the direction

indicated by the arrow (fig. a) then clip the loop onto the

stand (fig. b).

3 Place the AM antenna on a flat surface and in a direction

giving the best reception.

4 Connect the FM wire antenna into the FM antenna

socket.

For best results, extend the FM antenna fully and fix to a wall

or door frame. Don’t drape loosely or leave coiled up.

Using external antennas

To improve FM reception

Use a F connector (not supplied) to connect an external FM

antenna.

To improve AM reception

Connect a 5 m to 6 m (16 ft. to 20 ft.) length of vinyl-coated

wire to the AM antenna terminal without disconnecting the

supplied AM loop antenna.

For the best possible reception, suspend horizontally

outdoors.

Connecting an iPod

This receiver has a dedicated iPod/iPhone terminal that will

allow you to control playback of audio content from your iPod

using the controls of this receiver.

Note

• An iPod/iPhone can be connected to the receiver. For details

on supported models and versions of the respective products,

see Playing an iPod on page 19.

1 Switch the receiver into standby, and then use the iPod

cable to connect your iPod to the iPod/iPhone terminal on

the front panel of this receiver.

• For the cable connection, also refer to the operating

instructions for your iPod.

• When connecting an iPhone to this unit, keep the iPhone

at least 20 cm away from this unit. If the iPhone is kept

closer to this unit and a telephone call is received by the

iPhone, noise may be output from this device.

• iPod recharging occurs whenever an iPod is connected to this

unit. (Recharging is enabled only when the unit’s power is

turned on.)

ANTENNA

FM UNBAL

75

AM LOOP

2

1

3

4

fig. a

fig. b

ANTENNA

FM UNBAL

75

F connector

ANTENNA

AM LOOP

Outdoor

antenna

5 m to 6 m

(16 ft. to 20 ft.)

Indoor antenna

(vinyl-coated wire)

VSX-324-K-P_CMXESM.book 16 ページ２０１３年２月１３日　水曜日　午前９時１７分

02

Connecting your equipment

17

En

English

Français

Español

• For instructions on playing the iPod, see Playing an iPod on

page 19

.

Note

• When the ARC function is ON and the receiver is

connected to a compatible TV with an HDMI cable, and

you switch the input of the TV when the receiver’s

selection is iPod/USB input, the receiver may

automatically switch to TV. If this happens, switch the

receiver's input back to the original input, or turn OFF the

ARC function (see The HDMI Setup menu on page 30).

Connecting a USB device

It is possible to listen to two-channel audio using the USB

interface on the front of this receiver.

1 Switch the receiver into standby then connect your USB

device to the iPod/iPhone terminal on the front panel of

this receiver.

• This receiver does not support a USB hub.

• For instructions on playing the USB device, see Playing a

USB device on page 20.

Plugging in the receiver

Only plug in after you have connected all your components to

this receiver, including the speakers.

1 Plug the AC power cord into a convenient AC power

outlet.

CAUTION

• Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power cord

when your hands are wet as this could cause a short

circuit or electric shock. Do not place the unit, a piece of

furniture, etc., on the power cord, or pinch the cord.

Never make a knot in the cord or tie it with other cords.

The power cords should be routed such that they are not

likely to be stepped on. A damaged power cord can cause

a fire or give you an electrical shock. Check the power

cord once in a while. When you find it damaged, ask your

nearest PIONEER authorized service center or your dealer

for a replacement.

• The receiver should be disconnected by removing the

mains plug from the wall socket when not in regular use,

e.g., when on vacation.

Note

• After this receiver is connected to an AC outlet, a 2

second to 10 second HDMI initialization process begins.

You cannot carry out any operations during this process.

The HDMI indicator in the front panel display blinks

during this process, and you can turn on this receiver

once it has stopped blinking. When you set ARC at HDMI

setup to OFF, you can skip this process. For details, see

The HDMI Setup menu on page 30.

AV RECEIVER

MASTER

VOLUME

ET ENTER

iPod iPhone

VSX

-324

HDMI

5V 1A

USB cable that comes

with the iPod

This receiver

iPod/iPhone

AV RECEIVER

MASTER

VOLUME

E

TENTER

iPod iPhone

VSX

-324

HDMI

5V 1A

USB mass

storage device

This receiver

VSX-324-K-P_CMXESM.book 17 ページ２０１３年２月１３日　水曜日　午前９時１７分

Basic playback

18

En

03

Chapter 3:

Basic playback

Playing a source

Here are the basic instructions for playing a source (such as

a DVD disc) with your home theater system.

1 Switch on your system components and receiver.

Start by switching on the playback component (for example a

DVD player), your TV and subwoofer (if you have one), then

the receiver (press  RECEIVER).

• Make sure the setup microphone is disconnected.

2 Switch the TV input to the input that connects this

receiver.

For example, if you connected this receiver to the VIDEO

jacks on your TV, make sure that the VIDEO input is now

selected.

3 Press input function buttons to select the input function

you want to play.

• The input of the receiver will switch over, and you will be

able to operate other components using the remote

control. To operate the receiver, first press on

the remote control, then press the appropriate button to

operate.

• The input source can also be selected by using INPUT

SELECT buttons on the remote control, or by

using the front panel INPUT SELECTOR dial. In this case,

the remote control won’t switch operational modes.

If you selected the proper input source and there is still no

sound, select the audio input signal for playback (see

Selecting the audio input signal below).

4 Press AUTO/DIRECT to select ‘AUTO SURROUND’ and

start playback of the source.

If you’re playing a Dolby Digital or DTS surround sound DVD

disc, with a digital audio connection, you should hear

surround sound. If you’re playing a stereo source or if the

connection is an analog audio connection, you will only hear

sound from the front left/right speakers in the default

listening mode.

It is possible to check on the front panel display whether or

not surround sound playback is being performed properly.

If the display does not correspond to the input signal and

listening mode, check the connections and settings.

Note

• You may need to check the digital audio output settings

on your DVD player or digital satellite receiver. It should

be set to output Dolby Digital, DTS and 88.2 kHz/96 kHz

PCM (2 channel) audio, and if there is an MPEG audio

option, set this to convert the MPEG audio to PCM.

• Depending on your DVD player or source discs, you may

only get digital 2 channel stereo and analog sound. In this

case, the receiver must be set to a multichannel listening

mode if you want multichannel surround sound.

5 Use VOLUME +/– to adjust the volume level.

Turn down the volume of your TV so that all sound is coming

from the speakers connected to this receiver.

Selecting the audio input signal

The audio input signal can be selected for each input source.

Once it is set, the audio input that was selected will be

applied whenever you select the input source using the input

function buttons.

1 Press SIGNAL SEL to select the audio input signal

corresponding to the source component.

Each press cycles through the following:

• H – Selects an HDMI signal. H can be selected for BD,

DVD, SAT/CBL and GAME input. For other inputs, H

cannot be selected.

-

When the HDMI option in Setting the Audio options on

page 25 is set to THRU, the sound will be heard through

your TV, not from this receiver.

• A – Selects the analog inputs.

• C1/O1 – Selects the digital input. The coaxial 1 input is

selected for C1, and the optical 1 audio input is selected

for O1.

When H (HDMI) or C1/O1 (digital) is selected and the

selected audio input is not provided, A (analog) is

automatically selected.

Except BD, DVR/BDR input.

Note

• BD and GAME inputs are fixed to H (HDMI). It cannot

be changed.

• For the TV input, only A (analog) or C1/O1 (digital) can

be selected. However, if the ARC at

HDMI Setup is set

to ON, the input is fixed to H (HDMI) and cannot be

changed.

•When set to H (HDMI) or C1/O1 (digital), 2 lights when

a Dolby Digital signal is input, and DTS lights when a DTS

signal is input.

•When the H (HDMI) is selected, the A and DIGITAL

indicators are off (see page 7).

BD DVD

INPUT SELECT

SOURCESLEEP

TV

CONTROL

CD

INPUT

CH

RECEIVER

TUNER

iPod/USB

SAT/CBL

GAME

TV

SIGNAL SEL

RECEIVER

ENTER

ADV SURR

ECO

AUTO/

DIRECT

MUTE

RETURN

AUDIO

PARAMETER

TOOLS

MENU

VOLUME

BAND

HOME

MENU

iPod CTRL

PTY

TOP

MENU

T

U

N

E

T

U

N

E

P

R

E

S

E

T

P

R

E

S

E

T

ALC/

STANDARD

STEREO

RECEIVER

CH

TUNER

iPod/USB

SAT/CBL

GAME

TV

SIGNAL SEL

Acous.EQ

PHASE

S.RETRIEVER

VOL

VSX-324-K-P_CMXESM.book 18 ページ２０１３年２月１３日　水曜日　午前９時１７分

Basic playback

19

En

03

English

Français

Español

• When digital input (optical or coaxial) is selected, this

receiver can only play back Dolby Digital, PCM (32 kHz to

96 kHz) and DTS (including DTS 96 kHz/24 bit) digital

signal formats. The compatible signals via the HDMI

terminals are: Dolby Digital, DTS, SACD (DSD 2ch only),

PCM (32 kHz to 192 kHz sampling frequencies), Dolby

TrueHD, Dolby Digital Plus, DTS-EXPRESS, DTS-HD

Master Audio and DVD Audio (including 192 kHz). With

other digital signal formats, set to A (analog).

• You may get digital noise when a LD or CD player

compatible with DTS is playing an analog signal. To

prevent noise, make the proper digital connections

(page 13) and set the signal input to C1/O1 (digital).

• Some DVD players don’t output DTS signals. For more

details, refer to the instruction manual supplied with your

DVD player.

Playing an iPod

This receiver has a dedicated iPod/iPhone terminal that will

allow you to control playback of audio content from your iPod

using the controls of this receiver.

Important

• Pioneer cannot under any circumstances accept

responsibility for any direct or indirect loss arising from

any inconvenience or loss of recorded material resulting

from the iPod failure.

Note

• This receiver is compatible with the audio of the iPod

touch (1st/2nd/3rd/4th/5th generation), iPod classic, iPod

nano (3rd/4th/5th/6th/7th generation), iPhone 3G, iPhone

3GS, iPhone 4, iPhone 4S, iPhone 5 and iPad mini.

However, that some of the functions may be restricted for

some models.

• This receiver has been developed and tested for the

software version of iPod/iPhone indicated on the website

of Pioneer (http://pioneer.jp/homeav/support/ios/na/).

• Installing software versions other than indicated on the

website of Pioneer to your iPod/iPhone may result in

incompatibility with this receiver.

• iPod and iPhone are licensed for reproduction of

noncopyrighted materials or materials the user is legally

permitted to reproduce.

• Features such as the equalizer cannot be controlled using

this receiver, and we recommend switching the equalizer

off before connecting.

• No sound will come from the headphone even when the

headphone is connected to the PHONES jack, when the

iPod is connected.

• Make sure the receiver is in standby when disconnecting

the iPod/iPhone.

1 Switch on the receiver and your TV.

See Connecting an iPod on page 16.

2 Switch the TV input so that it connects to the receiver.

• Switch the TV input to the input that connects this

receiver to the TV through the corresponding composite

cable.

Tip

• In order to enjoy the picture and/or sound from devices

connected to each terminal, select the input by doing the following.

HDMI

VIDEO AUDIO

COAXIAL

SPEAKERS

ANTENNA

OPTICAL

ASSIGNABLEASSIGNABLE

ASSIGNABLE

OUTIN IN

A

(

CD

)

MONITOR

OUT

DVD IN

ANALOG IN

(CD)

SAT/CBL

IN

DVD SAT/CBL GAME BD

(

TV

)

IN

1

IN

1

FM UNBAL

75

AM LOOP

FRONT CENTER

SURROUND

RLRL

RL

SAT/CBL GAME BD

TUNER

TV

DVD

CD

SAT/CBL TVDVD

DVDSAT/CBL

CD

TV

1.

A

SIGNAL SEL

DVD

SAT/CBL

A

SIGNAL SEL

O1

2.

SIGNAL SEL

C1

SIGNAL SEL

Audio Audio

Audio

Video/Audio (HDMI)

Video

Other than TV input

(TV input)

Audio

ANALOG IN1 audio

input terminal is

assigned to CD under

factory settings. If you

want to change this to

TV input, please

change the settings in

the Input Assign menu

(page 29).

VSX-324-K-P_CMXESM.book 19 ページ２０１３年２月１３日　水曜日　午前９時１７分

Basic playback

20

En

03

3 Press iPod/USB to switch the receiver to the iPod/USB

input.

The front panel display shows Loading while the receiver

verifies the connection and retrieves data from the iPod.

4 Use TOP MENU to display iPod Top menu.

When the display shows Top Menu you’re ready to play

music from the iPod.

• If after pressing iPod/USB the display shows NO DEVICE,

try switching off the receiver and reconnecting the iPod to

the receiver.

• The controls of your iPod will be inoperable when

connected to this receiver.

Playing back files stored on an iPod

To navigate songs on your iPod, you can take advantage of

the OSD of your TV connected to this receiver. You can also

control all operations for music in the front panel display of

this receiver.

• Note that non-roman characters in the title are displayed

as ‘*’.

• This feature is not available for photos or video clips on

your iPod.

Finding what you want to play

When your iPod is connected to this receiver, you can browse

songs stored on your iPod by playlist, artist, album name,

song name, genre or composer, similar to using your iPod

directly.

1Use

/

to select a category, then press ENTER to

browse that category.

• To return to the previous level any time, press RETURN.

2Use

/

to browse the selected category (e.g., albums).

•Use / to move to previous/next levels.

3 Continue browsing until you arrive at what you want to

play, then press



to start playback.

• If you’re in the song category, you can also press

ENTER

to start playback.

• You can play all of the songs in a particular category by

selecting the All item at the top of each category list. For

example, you can play all the songs by a particular artist.

Basic playback controls

This receiver’s remote control buttons can be used for

basic playback of files stored on an iPod.

• Press iPod/USB to switch the remote control to the iPod/

USB operation mode.

• During Audiobook playback, press / to switch the

playback speed: Faster Normal Slower

Switches between the iPod controls and the

receiver controls

This allows you to switch between performing iPod

operations via the receiver remote control or on the iPod

itself.

1 Press iPod CTRL to switch to the iPod controls.

• Press iPod CTRL again to switch back to the receiver

controls when you’re done.

Tip

• Change the receiver’s input to the iPod in one action by

pressing iPod iPhone DIRECT CONTROL on the front

panel to enable iPod operations on the iPod.

Playing a USB device

It is possible to listen to two-channel audio using the USB

interface on the front of this receiver.

Important

• Pioneer cannot guarantee compatibility (operation and/or

bus power) with all USB mass storage devices and

assumes no responsibility for any loss of data that may

occur when connected to this receiver.

Note

• This includes playback of WMA/MP3/MPEG-4 AAC files

(except files with copy-protection or restricted playback).

• Compatible USB devices include external magnetic hard

drives, portable flash memory (particularly keydrives) and

digital audio players (MP3 players) of format FAT16/32. It

is not possible to connect this receiver to a personal

computer for USB playback.

• With large amounts of data, it may take longer for the

receiver to read the contents of a USB device.

• If the file selected cannot be played back, this receiver

automatically skips to the next file playable.

• When the file currently being played back has no title

assigned to it, the file name is displayed in the OSD

instead; when neither the album name nor the artist

name is present, the row is displayed as a blank space.

• Note that non-roman characters in the playlist are

displayed as ‘*’.

• Make sure the receiver is in standby when disconnecting

the USB device.

1 Switch on the receiver and your TV.

See Connecting a USB device on page 17.

2 Switch the TV input so that it connects to the receiver.

• Switch the TV input to the input that connects this

receiver to the TV through the corresponding composite

cable.

3 Press iPod/USB

on the remote control to switch the

receiver to the

iPod/USB input.

Loading appears in the OSD as this receiver starts

recognizing the USB device connected. After the recognition,

a playback screen appears in the OSD and playback starts

automatically.

ENTER

ECO

MUTE

RETURN

AUDIO

PARAMETER

TOOLS

MENU

VOLUME

BAND

HOME

MENU

iPod CTRL

PTY

TOP

MENU

T

U

N

E

T

U

N

E

P

R

E

S

E

T

P

R

E

S

E

T

1

4

7

MIDNIGHT

2

5

8

SPEAKERS

LEV

SB CH

DISP

3

6

9

CH

CH SELECT

MUTE

TRE

BASS

VSX-324-K-P_CMXESM.book 20 ページ２０１３年２月１３日　水曜日　午前９時１７分

La page est en cours de chargement...

Pioneer VSX-324-K-P Manuel utilisateur

Ce manuel convient également à

Pioneer VSX-324-K-P Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents