RIDGID R692BBN Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
10 in. TABLE SAW
SCIE À TABLE de 254 mm (10 po)
SIERRA DE MESA de 254 mm (10 pulg.)
R4512
Cette scie a été conçue et fabriquée conformément aux strictes
normes de fiabilité, simplicité d’emploi et sécurité d’utilisation.
Correctement entretenu, cet outil vous donnera des années de
fonctionnement robuste et sans problème.
AVERTISSEMENT :
Pour réduire les risques de blessures, l’utilisateur
doit lire et veiller à bien comprendre le manuel
d’utilisation avant d’employer ce produit.
Su sierra ha sido diseñado y fabricado de conformidad con
nuestras estrictas normas para brindar fiabilidad, facilidad de
uso y seguridad para el operador. Con el debido cuidado, le
brindará muchos años de sólido funcionamiento y sin problemas.
ADVERTENCIA:
Para reducir el riesgo de lesiones, el usuario debe
leer y comprender el manual del operador antes de
usar este producto.
CONSERVER CE MANUEL POUR
FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL PARA
FUTURAS CONSULTAS
SAVE THIS MANUAL FOR FUTURE REFERENCE
Your saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
To register your RIDGID
product, please visit:
http://register.RIDGID.com
Pour enregistrer votre
produit de RIDGID,
s’il vous plaît la visite:
http://register.RIDGID.com
Para registrar su producto
de RIDGID, por favor visita:
http://register.RIDGID.com
45
2
Introduction ......................................................................................................................................................................2
Introduction / Introducción
General Safety Rules .....................................................................................................................................................3-4
Règles de sécurité générales / Reglas de seguridad generales
Specific Safety Rules .....................................................................................................................................................4-5
Règles de sécurité particulières / Reglas de seguridad específicas
Symbols ............................................................................................................................................................................ 6
Symboles / Símbolos
Electrical ........................................................................................................................................................................7-8
Caractéristiques électriques / Aspectos eléctricos
Glossary of Terms ............................................................................................................................................................. 9
Glossaire / Glosario de términos
Features .....................................................................................................................................................................10-12
Caractéristiques / Características
Tools Needed ..................................................................................................................................................................13
Outils nécessaires / Herramientas necesarias
Loose Parts ...............................................................................................................................................................14-15
Pièces détachées / Piezas sueltas
Assembly ...................................................................................................................................................................16-27
Assemblage / Armado
Operation ................................................................................................................................................................... 28-44
Utilisation / Funcionamiento
Adjustments ...............................................................................................................................................................45-48
Réglages / Ajustes
Maintenance ..............................................................................................................................................................49-50
Entretien / Mantenimiento
Troubleshooting .........................................................................................................................................................51-52
Dépannage / Solución de problemas
Warranty ......................................................................................................................................................................... 53
Garantie / Garantía
Parts Ordering and Service ...............................................................................................................................Back page
Commande de pièces et réparation / Pedidos de piezas y servicio
INTRODUCTION
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
* * *
Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la
conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à
utiliser et à entretenir.
* * *
Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto
se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
TABLE OF CONTENTS
3 - English
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read the operator’s manual
carefully. Learn the saw’s applications and limitations as
well as the specific potential hazards related to this tool.
GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH GROUNDED
SURFACES. For example, pipes, radiators, ranges,
refrigerator enclosures.
KEEP GUARDS IN PLACE and in good working order.
REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
KEEP WORK AREA CLEAN. Cluttered areas and benches
invite accidents. DO NOT leave tools or pieces of wood
on the saw while it is in operation.
DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe distance
from work area. Do not let visitors contact tool or extension
cord while operating.
MAKE WORKSHOP CHILDPROOF with padlocks and
master switches, or by removing starter keys.
DON’T FORCE TOOL. It will do the job better and safer
at the feed rate for which it was designed.
USE RIGHT TOOL. Don’t force the tool or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. Use only a
cord heavy enough to carry the current your product
will draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating. A wire
gauge size (A.W.G.) of at least 14 is recommended for an
extension cord 25 feet or less in length. If in doubt, use
the next heavier gauge. The smaller the gauge number,
the heavier the cord.
DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
are recommended when working outdoors. Also wear
protective hair covering to contain long hair.
ALWAYS WEAR EYE PROTECTION WITH SIDE
SHIELDS MARKED TO COMPLY WITH ANSI Z87.1.
Failure to do so could result in objects being thrown into
your eyes, resulting in possible serious injury.
SECURE WORK. Use clamps or a vise to hold work when
practical. It’s safer than using your hand and frees both
hands to operate tool.
DON’T OVERREACH. Keep proper footing and balance
at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for better and safer performance. Follow instructions
for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before servicing,
or when changing attachments, blades, bits, cutters, etc.,
all tools should be disconnected.
AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in any tool.
USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may risk injury.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of rotation of blade
or cutter only.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
THE POWER OFF. Don’t leave tool until it comes to a
complete stop.
PROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
DO NOT ABUSE CORD. Never yank cord to disconnect
from receptacle. Keep cord from heat, oil, and sharp
edges.
WHEN OPERATING A POWER TOOL OUTSIDE, USE
AN OUTDOOR EXTENSION CORD MARKED “W-A” OR
“W”. These cords are rated for outdoor use and reduce
the risk of electric shock.
ALWAYS KEEP THE BLADE GUARD AND RIVING KNIFE
(SPLITTER) IN PLACE and in working order.
KEEP BLADES CLEAN, SHARP, AND WITH SUFFICIENT
SET. Sharp blades minimize stalling and kickback.
KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from blades. Do not reach underneath work
or around or over the blade while blade is rotating. Do not
attempt to remove cut material when blade is moving.
4 - English
GENERAL SAFETY RULES
SPECIFIC SAFETY RULES
BLADE COASTS AFTER BEING TURNED OFF.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal
sparking of the motor could ignite fumes.
INSPECT TOOL CORDS PERIODICALLY. If damaged,
have repaired by a qualified service technician at an
authorized service facility. The conductor with insulation
having an outer surface that is green with or without yellow
stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to a
live terminal. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating blade.
INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole electrical
receptacle.
CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely
understood or if in doubt as to whether the tool is properly
grounded.
USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool’s plug.
DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
USE ONLY CORRECT BLADES. Do not use blades with
incorrect size holes. Never use blade washers or blade
bolts that are defective or incorrect. The maximum blade
capacity of your saw is 10 in. (254 mm).
BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS
ARE SECURE.
BE SURE BLADE PATH IS FREE OF NAILS. Inspect for
and remove all nails from lumber before cutting.
NEVER TOUCH BLADE or other moving parts during
use.
NEVER START A TOOL WHEN ANY ROTATING
COMPONENT IS IN CONTACT WITH THE WORKPIECE.
DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
WHEN SERVICING use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are not
listed may cause the risk of personal injury. Instructions for
safe use of accessories are included with the accessory.
DOUBLE CHECK ALL SETUPS. Make sure blade is tight
and not making contact with saw or workpiece before
connecting to power supply.
FIRMLY BOLT THE SAW TO A WORK BENCH OR LEG
STAND at approximately hip height.
DO NOT OPERATE THE SAW WITHOUT THE STAND
ON THE FLOOR.
GUARD AGAINST KICKBACK. Kickback occurs when
the blade stalls rapidly and workpiece is driven back
towards the operator. It can pull your hand into the blade
resulting in serious personal injury. Stay out of blade path
and turn switch off immediately if blade binds or stalls.
USE RIP FENCE. Always use a fence or straight edge
guide when ripping.
SUPPORT LARGE PANELS. To minimize risk of blade
pinching and kickback, always support large panels.
REMOVE ALL FENCES AND AUXILIARY TABLES before
transporting saw. Failure to do so can result in an accident
causing possible serious personal injury.
ALWAYS USE BLADE GUARD, RIVING KNIFE, AND
ANTI-KICKBACK PAWLS on all “through-sawing”
operations. Through-sawing operations are those in
which the blade cuts completely through the workpiece
as in ripping or cross cutting. Keep the blade guard down,
the anti-kickback pawls down, and the riving knife in
place.
ALWAYS SECURE WORK firmly against rip fence, miter
fence, or miter gauge.
ALWAYS USE A PUSH STICK FOR RIPPING NARROW
STOCK. A push stick is a device used to push a
workpiece through the blade instead of using your hands.
Size and shape can vary but the push stick must always
be narrower than the workpiece to prevent the push stick
from contacting the saw blade. When ripping narrow
stock, always use a push stick, or the jig mentioned in the
How to Make A Jig (For Rip Cutting Narrow Workpiece)
section of this manual, so your hand does not come close
to the saw blade. Use a featherboard and push blocks
for non-through cuts.
5 - English
SPECIFIC SAFETY RULES
WHEN MAKING NON-THROUGH RIP CUTS, always
use a push stick, push block, and/or featherboard so your
hands do not come within 3 inches of the saw blade.
WHEN RIPPING NARROW STOCK, always use a push
stick, push block, jig ( designed for narrow ripping), or
featherboard.
NEVER perform any operation “freehand” which means
using only your hands to support or guide the workpiece.
Always use either the rip fence or miter fence to position
and guide the work.
NEVER stand or have any part of your body in line with
the path of the saw blade.
NEVER reach behind, over, or within three inches of the
blade or cutter with either hand for any reason.
ALWAYS REMOVE THE RIP FENCE from the saw when
cross cutting.
DO NOT USE THE MITER GAUGE AND RIP FENCE
during the same operation.
NEVER use rip fence as cutoff gauge when cross
cutting.
NEVER attempt to free a stalled saw blade without first
turning the saw OFF and disconnecting the saw from the
power source.
PROVIDE ADEQUATE SUPPORT to the rear and sides
of the saw table for wide or long work pieces.
AVOID KICKBACKS (work thrown back toward you) by:
a) Keeping blade sharp.
b) Keeping rip fence parallel to the saw blade.
c) Keeping riving knife, anti-kickback pawls, and blade
guard in place and operating.
d) Not releasing the work before it is pushed all the way
past the saw blade using a push stick.
e) Not ripping work that is twisted or warped or does
not have a straight edge to guide along the fence.
IF THE POWER SUPPLY CORD IS DAMAGED, it must
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause your hand
to move into the cutting tool.
USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are not
listed may cause the risk of personal injury. Instructions for
safe use of accessories are included with the accessory.
MAKE SURE THE WORK AREA HAS AMPLE LIGHTING
to see the work and that no obstructions will interfere with
safe operation BEFORE performing any work using the
table saw.
ALWAYS TURN OFF SAW before disconnecting it, to
avoid accidental starting when reconnecting to power
supply.
ONLY USE BLADES within the thickness range stamped
on the riving knife.
THIS TOOL should have the following markings:
a) Wear eye protection.
b) Use saw blade guard and riving knife for every operation
for which it can be used, including all through sawing.
c) Keep hands out of the line of saw blade.
d) Use a push stick when required.
e) Pay particular attention to instructions on reducing
risk of kickback.
f) Do not perform any operation freehand.
g) Never reach around or over the saw blade.
NEVER CUT MORE THAN ONE PIECE OF MATERIAL
AT A TIME.
SAVE THESE INSTRUCTIONS. Refer to them frequently
and use to instruct other users. If you loan someone this
tool, loan them these instructions also.
CALIFORNIA PROPOSITION 65
WARNING:
This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities
may contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after handling.
Some examples of these chemicals are:
lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products and,
arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce
your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
6 - English
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection
Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Wet Conditions Alert Do not expose to rain or use in damp locations.
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
min Minutes Time
Alternating Current Type of current
n
o
No Load Speed Rotational speed, at no load
Class II Construction Double-insulated construction
.../min Per Minute Revolutions, strokes, surface speed, orbits, etc., per minute
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates important information not related to an
injury hazard, such as a situation that may result in property damage.
7 - English
ELECTRICAL
EXTENSION CORDS
Use only 3-wire extension cords that have 3-prong grounding
plugs and 3-pole receptacles that accept the tool's plug.
When using a power tool at a considerable distance from
the power source, use an extension cord heavy enough
to carry the current that the tool will draw. An undersized
extension cord will cause a drop in line voltage, resulting in
a loss of power and causing the motor to overheat. Use the
chart provided below to determine the minimum wire size
required in an extension cord. Only round jacketed cords
listed by Underwriter's Laboratories (UL) should be used.
**Ampere rating (on tool faceplate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
When working with the tool outdoors, use an extension cord
that is designed for outside use. This is indicated by the
letters “W-A” or “W” on the cord’s jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
WARNING:
Keep the extension cord clear of the working
area. Position the cord so that it will not get
caught on lumber, tools or other obstructions
while you are working with a power tool. Failure
to do so can result in serious personal injury.
WARNING:
Check extension cords before each use. If
damaged replace immediately. Never use
product with a damaged cord since touching
the damaged area could cause electrical shock
resulting in serious injury.
ELECTRICAL CONNECTION
This product is powered by a precision built electric motor.
It should be connected to a power supply that is 120 V, AC
only (normal household current), 60 Hz. Do not operate
this product on direct current (DC). A substantial voltage
drop will cause a loss of power and the motor will overheat.
If the saw does not operate when plugged into an outlet,
double check the power supply.
SPEED AND WIRING
The no-load speed of this tool is approximately 3,450 rpm.
This speed is not constant and decreases under a load or
with lower voltage. For voltage, the wiring in a shop is as
important as the motor’s horsepower rating. A line intended
only for lights cannot properly carry a power tool motor. Wire
that is heavy enough for a short distance will be too light for
a greater distance. A line that can support one power tool
may not be able to support two or three tools.
GROUNDING INSTRUCTIONS
This product must be grounded. In the event of a malfunction
or breakdown, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock. This
tool is equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug must be
plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
WARNING:
Improper connection of the grounding plug can
result in a risk of electric shock. When repair
or replacement of the cord is required, do not
connect the grounding wire to either flat blade
terminal. The wire with insulation having an
outer surface that is green with or without yellow
stripes is the grounding wire.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is for use on a nominal 120 volt circuit and has
a grounding plug similar to the plug illustrated in figure 1.
Only connect the product to an outlet having the same
configuration as the plug. Do not use an adapter with this
product.
Fig. 1
GROUNDING
PIN
120 V GROUNDED
OUTLET
8 - English
ELECTRICAL
WARNING:
To prevent possible electrical hazards, have a
qualified electrician check the line if you are not
certain that it is properly wired.
CHANGING MOTOR VOLTAGE
See Figures 2 - 4.
WARNING:
Electric shock can kill. To reduce the risk of
serious personal injury, never connect plug
to power source until all assembly steps are
completed.
NOTE: The table saw is prewired at the factory for 120 V,
60 Hz. Use the following procedures to change motor voltage
from 120 V to 240 V. This is an optional procedure to be
completed after the saw has been fully assembled.
Unplug the saw.
Remove the 6 screws that secure the rear panel of the
saw. Remove the panel.
Lower the motor to its lowest point.
Located on the top of the motor is the junction box.
Remove the phillips screw at the back of the junction
box then lift off the cover.
Remove and discard the electrical tape from the wire
connectors. Remove wire connectors.
Reconnect the leads.
Reinstall the wire connectors and wrap each wire with
two layers of new UL listed electrical tape.
Recheck your wiring with the wiring diagrams.
Reinstall the junction box cover using the phillips screw.
Cut off the 120 volt power cord plug and replace it with
a 3-prong 240 volt, 15 amp. UL listed plug.
Connect the power cord white and black leads,
respectively, to the “hot” plug blade terminals. Connect
the power cord green grounding wire to the plug ground
prong terminal.
Reinstall the rear panel.
Plug your table saw into a 220-240 V, 15 amp., 3-prong
receptacle. Make certain the receptacle is connected to
a 240 V, AC power supply through a 240 V branch circuit
having at least a 15 amp capacity and protected by a
15 amp time-delay fuse or circuit breaker.
Fig. 4
BLACK WHITEGREEN
L1
L2
G
1
2 3
4
RED BLACK
WHITE
YELLOW
240V
Fig. 3
GROUNDING
PIN
COVER OF
GROUNDED
OUTLET BOX
L2
L1
G
1
3
2
4
RED BLACK
BLACK
WHITE
WHITEGREEN
YELLOW
FOR USE WITH 220-240 VOLT
Fig. 2
9 - English
GLOSSARY OF TERMS
Pilot Hole (drill presses and scroll saws)
A small hole drilled in a workpiece that serves as a guide
for drilling large holes accurately or for insertion of a scroll
saw blade.
Push Blocks (jointer planers)
Device used to feed the workpiece over the jointer planer
cutterhead during any operation. This aid helps keep the
operator’s hands well away from the cutterhead.
Push Blocks and Push Sticks (table saws)
Devices used to feed the workpiece through the saw blade
during cutting operations. When making a narrow rip cut
without a jig or similar cutting aid, always use a push stick
(not a push block). A push block can be used for narrow
ripping operations, if a jig or similar cutting aid is used.
These aids help keep the operator’s hands well away from
the blade.
Rabbet
A non-through cut positioned on the end or edge of the
workpiece which produces a square, two-sided notch or
trough in the workpiece.
Resaw (table saws and band saws)
A cutting operation to reduce the thickness of the workpiece
to make thinner pieces.
Resin
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one
minute.
Ripping or Rip Cut (table saws)
A cutting operation along the length of the workpiece and
typically in the direction of the grain.
Riving Knife/Spreader/Splitter (table saws)
A metal piece, slightly thinner than the blade, which helps
keep the kerf open and also helps to prevent kickback.
Saw Blade Path
The area over, under, behind, or in front of the blade. As it
applies to the workpiece, that area which will be or has been
cut by the blade.
Snipe (planers)
Depression made at either end of a workpiece by cutter
blades when the workpiece is not properly supported.
Taper Cut
A cut where the material being cut has a different width at
the beginning of the cut from the end.
Through Sawing
Any cutting operation where the blade extends completely
through the thickness of the workpiece. This type of cut will
separate a single workpiece into two pieces.
Workpiece or Material
The item on which the operation is being done.
Worktable
Surface where the workpiece rests while performing a
cutting, drilling, planing, or sanding operation.
Anti-Kickback Pawls (radial arm and table saws)
A device which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Arbor
The shaft on which a blade or cutting tool is mounted.
Bevel Cut
A cutting operation made with the blade at any angle other
than 90° to the table surface.
Chamfer
A cut removing a wedge from a block so the end (or part of
the end) is angled rather than at 90°.
Compound Cut
A cross cut made with both a miter and a bevel angle.
Cross Cut
A cutting or shaping operation made across the grain or the
width of the workpiece.
Cutter Head (planers and jointer planers)
A rotating cutterhead with adjustable blades or knives. The
blades or knives remove material from the workpiece.
Dado Cut (table saws and compound sliding miter saws)
A non-through cut which produces a square, three-sided
notch or trough in the workpiece.
Featherboard (table saws)
A device used to help control the workpiece by guiding
it securely against the table or fence during any ripping
operation.
FPM or SPM
Feet per minute (or strokes per minute), used in reference
to blade movement.
Freehand
Performing a cut without the workpiece being guided by a
fence, miter fence, or other aids.
Gum
A sticky, sap-based residue from wood products.
Heel
Alignment of the blade to the fence.
Kerf
The material removed by the blade in a through cut or the
slot produced by the blade in a non-through or partial cut.
Kickback
A hazard that can occur when the blade binds or stalls,
throwing the workpiece in the direction of the spinning blade.
Miter Cut
A cutting operation made with the workpiece at any angle
to the blade other than 90°.
Non-Through Cuts (table saws and compound sliding
miter saws)
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece. This is a
cut where the blade will not cut the workpiece into two pieces.
10 - English
FEATURES
PRODUCT SPECIFICATIONS
Blade Arbor ...............................................................5/8 in.
Blade Diameter ...........................................................10 in.
Blade Tilt ..................................................................0˚ - 45˚
Rating ............................ 120/240 V ~, 13/6.5 Amps, 60 Hz
No Load Speed .....................................3,450 r/min. (RPM)
Cutting Depth at 0º: ............................................... 3-1/4 in.
Cutting Depth at 45º: ............................................. 2-1/4 in.
45
Fig. 5
MITER
GAUGE
TABLE
EXTENSION
MITER
GAUGE
GROOVE
SAW
BLADE
BLADE GUARD
ASSEMBLY
FRONT
RAIL
RIP FENCE
SCALE
LOCKING
HANDLE
SWITCH
ASSEMBLY
BEVEL
ADJUSTING
HANDWHEEL
BEVEL
LOCK KNOB
HEIGHT
LOCK
KNOB
BEVEL
SCALE
RIP
FENCE
RIVING KNIFE
RIP FENCE
STORAGE
BRACKETS
ANTI-KICKBACK
PAWLS
HEIGHT
ADJUSTING
HANDWHEEL
BLADE AND
WRENCH
STORAGE
MITER GAUGE
STORAGE
PUSH
STICK
MITER
GAUGE
GROOVE
11 - English
FEATURES
KNOW YOUR TABLE SAW
See Figure 5.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
ANTI-KICKBACK PAWLS - Kickback is a hazard in which
the workpiece is thrown back toward the operator. The teeth
on the removable anti-kickback pawls point away from the
workpiece. If the workpiece should be pulled back toward
the operator, the teeth dig into the wood to help prevent or
reduce the possibility of kickback.
BEVEL ADJUSTING HANDWHEEL/BEVEL LOCK KNOB -
The bevel adjusting handwheel, located on the side of the
cabinet, is used to adjust the bevel angle of the blade.The
bevel lock knob locks the angle setting of the blade.
BEVEL SCALE - The easy-to-read scale on the front of the
cabinet shows the exact blade angle.
BLADE - For maximum performance, it is recommended
that you use the 10 in. carbide tipped combination blade
provided with your saw. The blade is raised and lowered with
the height adjusting handwheel. Bevel angles are locked with
the bevel lock knob. Additional blade styles of the same high
quality are available for specific operations such as ripping.
Your local dealer can provide you with complete information.
Blade kerf width must be within the limits stamped on the
riving knife.
WARNING:
Do not use blades rated less than the speed of
this tool. Failure to heed this warning could result
in personal injury.
BLADE GUARD - Always keep the removable blade guard
down over the saw blade for through-sawing cuts.
HEIGHT ADJUSTING HANDWHEEL/ HEIGHT LOCK
KNOB - The height adusting handwheel, located on the
front of the cabinet, is used to lower and raise the blade for
height adjustments or blade replacement. The height lock
knob locks the height setting of the blade.
MITER GAUGE - The miter gauge aligns the wood for a cross
cut. The easy-to-read indicator shows the exact angle for a
miter cut, with adjustable stops at 90° and 45°.
MITER GAUGE GROOVES - The miter gauge rides in the
grooves on the saw table.
RIP FENCE - A sturdy metal fence guides the workpiece and
is secured with the locking handle. Grooves run along the
top and sides of the rip fence for use with optional clamps
and accessories.
RIVING KNIFE - A removable metal piece of the blade
guard assembly, slightly thinner than the saw blade, which
helps keep the kerf open and prevent kickback. When in the
through sawing, or “up” position, it is higher than the saw
blade. When in the non-through sawing, or “down” position,
it is below the saw blade teeth.
RIP SCALE - Located on the front rail, the easy-to-read rip
scale provides precise measurements for rip cuts.
SWITCH ASSEMBLY - This saw has an easy access switch
assembly located below the front rail. To lock the switch in
the OFF position, remove the switch key from the switch.
Place the key in a location that is inaccessible to children
and others not qualified to use the tool.
TABLE EXTENSION - Located on each side of the saw table,
the table extensions give the operator additional support
when cutting wide workpieces.
12 - English
FEATURES
WARNING:
ALWAYS make sure your workpiece is not in
contact with the blade before operating the
switch to start the tool. Failure to heed this
warning could cause the workpiece to be kicked
back toward the operator and result in serious
personal injury.
WARNING:
To reduce the risk of accidental starting, always
make sure the switch is in the OFF ( O ) position
before plugging tool into the power source.
OPERATING COMPONENTS
The upper portion of the blade projects up through the table
and is surrounded by an insert called the throat plate. The
height of the blade is set with a handwheel on the front of the
cabinet. Detailed instructions are provided in the Operation
section of this manual for the basic cuts: cross cuts, miter
cuts, bevel cuts, and compound cuts.
The rip fence is used to position work for lengthwise cuts.
A scale on the front rail shows the distance between the rip
fence and the blade.
It is very important to use the blade guard assembly for
all through-sawing operations. The blade guard assembly
includes: riving knife, anti-kickback pawls, and blade guard.
SWITCH ASSEMBLY
See Figure 6.
This saw is equipped with a switch assembly that has a
built-in locking feature. This feature is intended to prevent
unauthorized and possible hazardous use by children and
others.
TO TURN YOUR SAW ON:
With the switch key inserted into the switch, lift the switch
button to turn ON ( l ).
TO TURN YOUR SAW OFF:
Press the switch button down to turn OFF ( O ).
TO LOCK YOUR SAW:
Press the switch button down.
Remove the switch key from the switch and store in a
safe, secure location.
WARNING:
Always remove the switch key when the tool is
not in use and keep it in a safe place. In the event
of a power failure, turn the switch OFF ( O ) and
remove the key. This action will prevent the tool
from accidentally starting when power returns.
Fig. 6
SWITCH KEY
REMOVED
SWITCH
OFF
SWITCH
ON
SWITCH
COVER
NOTE: For clarity, the cover is not shown
in the illustrations below.
NOTE: The cover does not need to be removed
to remove the switch key.
13 - English
TOOLS NEEDED
The following tools (not included or drawn to scale) are needed for assembly and adjustments:
Fig. 7
FRAMING SQUARE
PHILLIPS
SCREWDRIVER
FLATHEAD
SCREWDRIVER
WRENCH
4 mm, 8 mm, 10 mm, 13 mm, 14 mm
SOCKET WRENCH
(8 mm, 13 mm SOCKET)
C-CLAMPS
COMBINATION
SQUARE
14 - English
LOOSE PARTS
Fig. 8
The following items are included with the table saw:
A. Blade Guard .............................................................. 1
B. Anti-Kickback Pawls ................................................. 1
C. Miter Gauge ............................................................... 1
D. Rip Fence .................................................................. 1
E. Height Adjusting Handwheel, Washer, and Knob ..... 1
F. Bevel Adjusting Handwheel, Washer, and Knob ....... 1
G. Push Stick ................................................................. 1
H. Blade Wrench, open end ........................................... 1
I. Blade Wrench, closed end ........................................ 1
J. Hex Keys (3 mm, 4 mm, 5 mm, 6 mm, 8 mm)........... 1
K. Rear Rail .................................................................... 2
L. Front Rail ................................................................... 2
M. Rail Connector Bar .................................................... 3
N. Table Extensions ....................................................... 2
O. Spreader Bar ............................................................. 1
P. Dust Chute ................................................................ 1
Q. Throat Plate ............................................................... 1
R. Front End Cap (left and right) .................................... 2
S. Back End Cap (left and right) .................................... 2
Not shown:
T. Fastener Pack - Large (contents noted on pack) ...... 1
U. Fastener Pack - Small (contents noted on pack) ...... 1
V. Caster Fastener Bag - Small ..................................... 1
A
R
S
O
B
P
C
J
D
K
K
Q
E, F
L
M
G
N
L
H
I
15 - English
LOOSE PARTS
A. Leg Stand Side Sections ........................................... 2
B. Leg Stand Front and Back ......................................... 2
C. Outer Corners ............................................................ 4
D. Caster Assembly........................................................ 1
E. Center Support .......................................................... 1
Fig. 9
A
H
B
I
C
D
E
F
G
F. Rear Axle Assembly ................................................... 1
G. Front Axle .................................................................. 1
H. Rip Fence Storage Brackets ...................................... 2
I. Foot ........................................................................... 4
16 - English
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully lift the saw from the carton and place on a level
work surface.
NOTE: This tool is heavy. To avoid back injury, keep your
knees bent and lift with your legs, not your back, and get
help when needed.
WARNING:
Do not use this product if any parts on the
Loose Parts List are already assembled to
your product when you unpack it. Parts on this
list are not assembled to the product by the
manufacturer and require customer installation.
Use of a product that may have been improperly
assembled could result in serious personal injury.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the tool.
NOTE: A box containing some of the Loose Parts is
inside the saw cabinet. Also, remove the foam block from
between the saw’s housing and the motor.
The saw is factory set for accurate cutting. After assembling
it, check for accuracy. If shipping has influenced the
settings, refer to specific procedures explained in this
manual.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
WARNING:
If any parts are damaged or missing, do not
operate this tool until the parts are replaced. Use
of this product with damaged or missing parts
could result in serious personal injury.
WARNING:
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly
is complete. Failure to comply could result in
accidental starting and possible serious personal
injury.
WARNING:
Do not lift the saw without help. Hold it close
to your body. Keep your knees bent and lift
with your legs, not your back. Ignoring these
precautions can result in back injury.
WARNING:
Never stand directly in line with the blade or allow
hands to come closer than 3 in. to the blade. Do
not reach over or across the blade. Failure to
heed this warning can result in serious personal
injury.
WARNING:
To avoid serious personal injury, never operate
the saw if it is not mounted to the supplied leg
stand. NEVER operate the saw on the floor.
17 - English
ASSEMBLY
TABLE
EXTENSION
TABLE
EXTENSION
BOARDS
FLAT
WASHER
LOCK
WASHER
BOLT
BOLT
SAW
TABLE
SAW
TABLE
LEG STAND
SECTION
OUTER
CORNER
Fig. 10
Fig. 11
Fig. 12
INSTALLING THE TABLE EXTENSIONS
See Figures 10 - 11.
NOTE: It is helpful to place two inch-thick boards on the floor
before lifting the saw table and motor housing from the box.
This will make it easier to assemble parts, and to move the
saw and set it upright.
Lift the saw table and motor housing from the box and
position it on the boards as shown.
Loosen the plastic wrap from the table and lift each side
to remove the wrapping.
From the large fastener pack, locate the following parts:
6 Bolts (M10 x 25)
6 Lock washers (M10)
6 Flat washers (M10)
With the table saw in the upside down position, place a
table extension against the table top, on the same side as
the power cord. The larger holes in the extension should
be aligned with the holes in the saw table.
Make sure the edges of the table extensions are aligned
with the edges of the table.
Insert a lock washer and flat washer over a bolt. Thread
the bolt into the holes in the table extension and saw
table. Repeat for the two remaining holes.
Repeat above step on the other table extension.
Using an 8 mm socket, tighten the socket head bolts. Do
not tighten completely.
ASSEMBLING THE LEG STAND
See Figure 12.
Locate the following parts:
4 Leg stand sections
4 Outer corners
From the small fastener pack, locate the following parts:
24 Bolts (M6 x 10)
Place an outer corner outside a leg stand section.
NOTE: The top of the outer corner has a bent tab and
hole for assembly to the saw cabinet.
Insert a bolt into each of the three holes and finger tighten.
Repeat with remaining corners and leg stand sections.
Using a 4 mm hex key, tighten all bolts securely.
NOTE: The front of the stand is the section with the
English WARNING label attached.
18 - English
ASSEMBLY
ASSEMBLING THE LEG STAND ONTO THE
SAW CABINET
See Figures 13 - 14.
WARNING:
Only install the dust chute when using a four
inch dust collection system. Failure to heed this
warning could result in serious personal injury or
death. Clean saw dust from the cabinet regularly.
NOTE: Make sure the foam block has been removed before
installing the dust chute.
Place the dust chute on top of the saw cabinet. The word
“FRONT” and the arrow should align with front panel of
the saw and the registration ridges should align with the
grooves.
Place the assembled leg stand over the dust chute as
shown.
Locate the following from the small fastener pack:
4 Flat washers
4 Lock washers
4 Bolts
Slide a lock washer and a flat washer over each bolt.
Thread a bolt into each of the 4 holes at the corners of
the leg stand.
Using a 6mm hex key, securely tighten the bolts.
ASSEMBLING THE CASTER SET
See Figures 15 - 16.
Remove the bolts and nuts from the caster assembly and
the front axle assembly.
NOTE: Use a 13 mm wrench and a 14 mm wrench for the
nuts and the bolts.
Attach the caster to the front axle by sliding the bolt
through the holes and placing the nut over the bolt.
Securely tighten the nut.
Remove the bolts and nuts from the rear and front axle
assemblies.
NOTE: Use a 6 mm hex wrench to hold the bolt and a
13 mm wrench to loosen the nut.
Position the front and rear axles as shown.
Attach the center support to the front axle assembly.
Slide the bolt through the hole in the axle center piece
and thread the nut over the bolt. Tighten the nut.
Attach the center support to the rear axle.
Fig. 13
Fig. 15
Fig. 16
DUST CHUTE
FLAT
WASHER
CASTER
REAR AXLE
ASSEMBLY
FRONT AXLE
ASSEMBLY
FRONT AXLE
ASSEMBLY
NUT
NUT
NUT
LOCK
WASHER
CENTER
SUPPORT
BOLT
BOLT
BOLT
Fig. 14
19 - English
ASSEMBLY
INSTALLING THE CASTER SET TO THE LEG
STAND
See Figure 17.
Slide the caster set into the leg stand, aligning the holes
in the caster assembly with the holes in the leg stand.
NOTE: Position the pedal as shown, so that it will be on
the left of the saw when the saw is upright.
Locate the following from the small fastener pack:
8 Bolts (M8 x 16)
Insert the bolts into the holes in the leg stand and through
the holes in each caster.
Using a 5 mm hex key, securely tighten the bolts.
Position the feet on the stand by pressing them into place.
INSTALLING RIP FENCE STORAGE BRACKETS
See Figure 18.
Remove the pre-installed bolt and nut from each bracket.
Insert a bolt through the hole in each bracket, aligning it
as shown with the hole in the stand.
Thread the nut over the bolt. Using a 5 mm hex key,
securely tighten each bolt.
SETTING THE SAW UPRIGHT
See Figure 19.
NOTE: The saw is heavy and requires several people for
this procedure.
Tilt the saw until it rests on the back side of the cabinet.
Raise saw carefully until it sits upright.
To raise the saw table, step down on the pedal until it
locks.
Roll the table saw to the desired location making sure
the surface is firm and level.
Pull up on the pedal to slowly lower the table saw.
Fig. 18
Fig. 19
SOCKET
HEAD BOLT
CASTER
ASSEMBLY
BOLT
BRACKET
NUT
PEDAL
FEET
Fig. 17
TO LOWER
20 - English
ASSEMBLY
Fig. 20
INSTALLING THE HEIGHT ADJUSTING
HANDWHEEL
See Figure 20.
NOTE: The height adjusting handwheel knob and the bevel
adjusting handwheel knob act as locks. To lock the wheel for
operation, turn the knob clockwise until it is securely tightened.
Slide the handwheel over the bolt above the bevel adjustment
scale on the front of the saw.
Slide the washer over the bolt.
Screw the knob securely onto the bolt.
INSTALLING THE BEVEL ADJUSTING
HANDWHEEL
See Figure 21.
Slide the bevel adjusting handwheel over the bolt on the
side of the saw.
Slide the washer over the bolt.
Screw the knob securely onto the bolt.
ACCESSORY STORAGE
See Figure 22.
Storage for the blade, blade wrench and miter gauge is
located on the side of the saw. The miter gauge may be
stored by sliding it into the slots.
The push stick contains a magnet. When not in use, the push
stick may be stored at a convenient location on the saw.
HEIGHT
ADJUSTING
HANDWHEEL
BEVEL
ADJUSTING
HANDWHEEL
BOLT
BOLT
KNOB
WASHER
WASHER
KNOB
KNOB
Fig. 21
Fig. 22
MITER GAUGE
STORAGE
BLADE AND
WRENCH
STORAGE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156

RIDGID R692BBN Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur

dans d''autres langues