RIDGID R692BBN Manuel utilisateur

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

10 in. TABLE SAW

SCIE À TABLE de 254 mm (10 po)

SIERRA DE MESA de 254 mm (10 pulg.)

R4512

Cette scie a été conçue et fabriquée conformément aux strictes

normes de fiabilité, simplicité d’emploi et sécurité d’utilisation.

Correctement entretenu, cet outil vous donnera des années de

fonctionnement robuste et sans problème.

AVERTISSEMENT :

Pour réduire les risques de blessures, l’utilisateur

doit lire et veiller à bien comprendre le manuel

d’utilisation avant d’employer ce produit.

Su sierra ha sido diseñado y fabricado de conformidad con

nuestras estrictas normas para brindar fiabilidad, facilidad de

uso y seguridad para el operador. Con el debido cuidado, le

brindará muchos años de sólido funcionamiento y sin problemas.

ADVERTENCIA:

Para reducir el riesgo de lesiones, el usuario debe

leer y comprender el manual del operador antes de

usar este producto.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator

safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING:

To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.

To register your RIDGID

product, please visit:

http://register.RIDGID.com

Pour enregistrer votre

produit de RIDGID,

s’il vous plaît la visite:

http://register.RIDGID.com

Para registrar su producto

de RIDGID, por favor visita:

http://register.RIDGID.com

45

2

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 General Safety Rules .....................................................................................................................................................3-4

Règles de sécurité générales / Reglas de seguridad generales

 Specific Safety Rules .....................................................................................................................................................4-5

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ............................................................................................................................................................................ 6

Symboles / Símbolos

Electrical ........................................................................................................................................................................7-8

Caractéristiques électriques / Aspectos eléctricos

Glossary of Terms ............................................................................................................................................................. 9

Glossaire / Glosario de términos

 Features .....................................................................................................................................................................10-12

Caractéristiques / Características

 Tools Needed ..................................................................................................................................................................13

Outils nécessaires / Herramientas necesarias

 Loose Parts ...............................................................................................................................................................14-15

Pièces détachées / Piezas sueltas

 Assembly ...................................................................................................................................................................16-27

Assemblage / Armado

 Operation ................................................................................................................................................................... 28-44

Utilisation / Funcionamiento

 Adjustments ...............................................................................................................................................................45-48

Réglages / Ajustes

 Maintenance ..............................................................................................................................................................49-50

Entretien / Mantenimiento

Troubleshooting .........................................................................................................................................................51-52

Dépannage / Solución de problemas

 Warranty ......................................................................................................................................................................... 53

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back page

Commande de pièces et réparation / Pedidos de piezas y servicio

INTRODUCTION

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

TABLE OF CONTENTS

3 - English

GENERAL SAFETY RULES

WARNING:

Read and understand all instructions. Failure to

follow all instructions listed below, may result in

electric shock, fire and/or serious personal injury.

READ ALL INSTRUCTIONS

 KNOW YOUR POWER TOOL. Read the operator’s manual

carefully. Learn the saw’s applications and limitations as

well as the specific potential hazards related to this tool.

 GUARD AGAINST ELECTRICAL SHOCK BY

PREVENTING BODY CONTACT WITH GROUNDED

SURFACES. For example, pipes, radiators, ranges,

refrigerator enclosures.

 KEEP GUARDS IN PLACE and in good working order.

 REMOVE ADJUSTING KEYS AND WRENCHES. Form

habit of checking to see that keys and adjusting wrenches

are removed from tool before turning it on.

 KEEP WORK AREA CLEAN. Cluttered areas and benches

invite accidents. DO NOT leave tools or pieces of wood

on the saw while it is in operation.

 DO NOT USE IN DANGEROUS ENVIRONMENTS. Do

not use power tools in damp or wet locations or expose

to rain. Keep the work area well lit.

 KEEP CHILDREN AND VISITORS AWAY. All visitors

should wear safety glasses and be kept a safe distance

from work area. Do not let visitors contact tool or extension

cord while operating.

 MAKE WORKSHOP CHILDPROOF with padlocks and

master switches, or by removing starter keys.

 DON’T FORCE TOOL. It will do the job better and safer

at the feed rate for which it was designed.

 USE RIGHT TOOL. Don’t force the tool or attachment to

do a job it was not designed for. Don’t use it for a purpose

not intended.

 USE THE PROPER EXTENSION CORD. Make sure

your extension cord is in good condition. Use only a

cord heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating. A wire

gauge size (A.W.G.) of at least 14 is recommended for an

extension cord 25 feet or less in length. If in doubt, use

the next heavier gauge. The smaller the gauge number,

the heavier the cord.

 DRESS PROPERLY. Do not wear loose clothing, gloves,

neckties, or jewelry. They can get caught and draw you

into moving parts. Rubber gloves and nonskid footwear

are recommended when working outdoors. Also wear

protective hair covering to contain long hair.

 ALWAYS WEAR EYE PROTECTION WITH SIDE

SHIELDS MARKED TO COMPLY WITH ANSI Z87.1.

Failure to do so could result in objects being thrown into

your eyes, resulting in possible serious injury.

 SECURE WORK. Use clamps or a vise to hold work when

practical. It’s safer than using your hand and frees both

hands to operate tool.

 DON’T OVERREACH. Keep proper footing and balance

at all times.

 MAINTAIN TOOLS WITH CARE. Keep tools sharp and

clean for better and safer performance. Follow instructions

for lubricating and changing accessories.

 DISCONNECT TOOLS. When not in use, before servicing,

or when changing attachments, blades, bits, cutters, etc.,

all tools should be disconnected.

 AVOID ACCIDENTAL STARTING. Be sure switch is off

when plugging in any tool.

 USE RECOMMENDED ACCESSORIES. Consult the

operator’s manual for recommended accessories. The

use of improper accessories may risk injury.

 NEVER STAND ON TOOL. Serious injury could occur if

the tool is tipped or if the cutting tool is unintentionally

contacted.

 CHECK DAMAGED PARTS. Before further use of the

tool, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment

of moving parts, binding of moving parts, breakage of

parts, mounting and any other conditions that may affect

its operation. A guard or other part that is damaged must

be properly repaired or replaced by an authorized service

center to avoid risk of personal injury.

 USE THE RIGHT DIRECTION OF FEED. Feed work into

a blade or cutter against the direction of rotation of blade

or cutter only.

 NEVER LEAVE TOOL RUNNING UNATTENDED. TURN

THE POWER OFF. Don’t leave tool until it comes to a

complete stop.

 PROTECT YOUR LUNGS. Wear a face or dust mask if

the cutting operation is dusty.

 PROTECT YOUR HEARING. Wear hearing protection

during extended periods of operation.

 DO NOT ABUSE CORD. Never yank cord to disconnect

from receptacle. Keep cord from heat, oil, and sharp

edges.

 WHEN OPERATING A POWER TOOL OUTSIDE, USE

AN OUTDOOR EXTENSION CORD MARKED “W-A” OR

“W”. These cords are rated for outdoor use and reduce

the risk of electric shock.

 ALWAYS KEEP THE BLADE GUARD AND RIVING KNIFE

(SPLITTER) IN PLACE and in working order.

 KEEP BLADES CLEAN, SHARP, AND WITH SUFFICIENT

SET. Sharp blades minimize stalling and kickback.

 KEEP HANDS AWAY FROM CUTTING AREA. Keep

hands away from blades. Do not reach underneath work

or around or over the blade while blade is rotating. Do not

attempt to remove cut material when blade is moving.

4 - English

GENERAL SAFETY RULES

SPECIFIC SAFETY RULES

 BLADE COASTS AFTER BEING TURNED OFF.

 NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal

sparking of the motor could ignite fumes.

 INSPECT TOOL CORDS PERIODICALLY. If damaged,

have repaired by a qualified service technician at an

authorized service facility. The conductor with insulation

having an outer surface that is green with or without yellow

stripes is the equipment-grounding conductor. If repair

or replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to a

live terminal. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating blade.

 INSPECT EXTENSION CORDS PERIODICALLY and

replace if damaged.

 GROUND ALL TOOLS. If tool is equipped with three-

prong plug, it should be plugged into a three-hole electrical

receptacle.

 CHECK WITH A QUALIFIED ELECTRICIAN or service

personnel if the grounding instructions are not completely

understood or if in doubt as to whether the tool is properly

grounded.

 USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire

extension cords that have 3-prong grounding plugs and

3-pole receptacles that accept the tool’s plug.

 DO NOT MODIFY the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified

electrician.

 KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND

GREASE. Always use a clean cloth when cleaning. Never

use brake fluids, gasoline, petroleum-based products, or

any solvents to clean tool.

 STAY ALERT AND EXERCISE CONTROL. Watch what

you are doing and use common sense. Do not operate

tool when you are tired. Do not rush.

 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT

ON AND OFF. Have defective switches replaced by an

authorized service center.

 USE ONLY CORRECT BLADES. Do not use blades with

incorrect size holes. Never use blade washers or blade

bolts that are defective or incorrect. The maximum blade

capacity of your saw is 10 in. (254 mm).

 BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS

ARE SECURE.

 BE SURE BLADE PATH IS FREE OF NAILS. Inspect for

and remove all nails from lumber before cutting.

 NEVER TOUCH BLADE or other moving parts during

use.

 NEVER START A TOOL WHEN ANY ROTATING

COMPONENT IS IN CONTACT WITH THE WORKPIECE.

 DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY

MEDICATION.

 WHEN SERVICING use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

 USE ONLY RECOMMENDED ACCESSORIES listed in

this manual or addendums. Use of accessories that are not

listed may cause the risk of personal injury. Instructions for

safe use of accessories are included with the accessory.

 DOUBLE CHECK ALL SETUPS. Make sure blade is tight

and not making contact with saw or workpiece before

connecting to power supply.

 FIRMLY BOLT THE SAW TO A WORK BENCH OR LEG

STAND at approximately hip height.

DO NOT OPERATE THE SAW WITHOUT THE STAND

ON THE FLOOR.

 GUARD AGAINST KICKBACK. Kickback occurs when

the blade stalls rapidly and workpiece is driven back

towards the operator. It can pull your hand into the blade

resulting in serious personal injury. Stay out of blade path

and turn switch off immediately if blade binds or stalls.

 USE RIP FENCE. Always use a fence or straight edge

guide when ripping.

 SUPPORT LARGE PANELS. To minimize risk of blade

pinching and kickback, always support large panels.

 REMOVE ALL FENCES AND AUXILIARY TABLES before

transporting saw. Failure to do so can result in an accident

causing possible serious personal injury.

 ALWAYS USE BLADE GUARD, RIVING KNIFE, AND

ANTI-KICKBACK PAWLS on all “through-sawing”

operations. Through-sawing operations are those in

which the blade cuts completely through the workpiece

as in ripping or cross cutting. Keep the blade guard down,

the anti-kickback pawls down, and the riving knife in

place.

 ALWAYS SECURE WORK firmly against rip fence, miter

fence, or miter gauge.

 ALWAYS USE A PUSH STICK FOR RIPPING NARROW

STOCK. A push stick is a device used to push a

workpiece through the blade instead of using your hands.

Size and shape can vary but the push stick must always

be narrower than the workpiece to prevent the push stick

from contacting the saw blade. When ripping narrow

stock, always use a push stick, or the jig mentioned in the

How to Make A Jig (For Rip Cutting Narrow Workpiece)

section of this manual, so your hand does not come close

to the saw blade. Use a featherboard and push blocks

for non-through cuts.

5 - English

SPECIFIC SAFETY RULES

 WHEN MAKING NON-THROUGH RIP CUTS, always

use a push stick, push block, and/or featherboard so your

hands do not come within 3 inches of the saw blade.

 WHEN RIPPING NARROW STOCK, always use a push

stick, push block, jig ( designed for narrow ripping), or

featherboard.

 NEVER perform any operation “freehand” which means

using only your hands to support or guide the workpiece.

Always use either the rip fence or miter fence to position

and guide the work.

 NEVER stand or have any part of your body in line with

the path of the saw blade.

 NEVER reach behind, over, or within three inches of the

blade or cutter with either hand for any reason.

 ALWAYS REMOVE THE RIP FENCE from the saw when

cross cutting.

 DO NOT USE THE MITER GAUGE AND RIP FENCE

during the same operation.

 NEVER use rip fence as cutoff gauge when cross

cutting.

 NEVER attempt to free a stalled saw blade without first

turning the saw OFF and disconnecting the saw from the

power source.

 PROVIDE ADEQUATE SUPPORT to the rear and sides

of the saw table for wide or long work pieces.

 AVOID KICKBACKS (work thrown back toward you) by:

a) Keeping blade sharp.

b) Keeping rip fence parallel to the saw blade.

c) Keeping riving knife, anti-kickback pawls, and blade

guard in place and operating.

d) Not releasing the work before it is pushed all the way

past the saw blade using a push stick.

e) Not ripping work that is twisted or warped or does

not have a straight edge to guide along the fence.

 IF THE POWER SUPPLY CORD IS DAMAGED, it must

be replaced only by the manufacturer or by an authorized

service center to avoid risk.

 AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause your hand

to move into the cutting tool.

 USE ONLY RECOMMENDED ACCESSORIES listed in

this manual or addendums. Use of accessories that are not

listed may cause the risk of personal injury. Instructions for

safe use of accessories are included with the accessory.

 MAKE SURE THE WORK AREA HAS AMPLE LIGHTING

to see the work and that no obstructions will interfere with

safe operation BEFORE performing any work using the

table saw.

 ALWAYS TURN OFF SAW before disconnecting it, to

avoid accidental starting when reconnecting to power

supply.

 ONLY USE BLADES within the thickness range stamped

on the riving knife.

 THIS TOOL should have the following markings:

a) Wear eye protection.

b) Use saw blade guard and riving knife for every operation

for which it can be used, including all through sawing.

c) Keep hands out of the line of saw blade.

d) Use a push stick when required.

e) Pay particular attention to instructions on reducing

risk of kickback.

f) Do not perform any operation freehand.

g) Never reach around or over the saw blade.

 NEVER CUT MORE THAN ONE PIECE OF MATERIAL

AT A TIME.

 SAVE THESE INSTRUCTIONS. Refer to them frequently

and use to instruct other users. If you loan someone this

tool, loan them these instructions also.

CALIFORNIA PROPOSITION 65

WARNING:

This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities

may contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products and,

• arsenic and chromium from chemically treated lumber.

Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce

your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are

specially designed to filter out microscopic particles.

6 - English

SYMBOLS

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the tool better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

No Hands Symbol

Failure to keep your hands away from the blade will result in

serious personal injury.

Wet Conditions Alert Do not expose to rain or use in damp locations.

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

min Minutes Time

Alternating Current Type of current

n

o

No Load Speed Rotational speed, at no load

Class II Construction Double-insulated construction

.../min Per Minute Revolutions, strokes, surface speed, orbits, etc., per minute

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

7 - English

ELECTRICAL

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong grounding

plugs and 3-pole receptacles that accept the tool's plug.

When using a power tool at a considerable distance from

the power source, use an extension cord heavy enough

to carry the current that the tool will draw. An undersized

extension cord will cause a drop in line voltage, resulting in

a loss of power and causing the motor to overheat. Use the

chart provided below to determine the minimum wire size

required in an extension cord. Only round jacketed cords

listed by Underwriter's Laboratories (UL) should be used.

**Ampere rating (on tool faceplate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25' 16 16 16 16 14 14

50' 16 16 16 14 14 12

100' 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

When working with the tool outdoors, use an extension cord

that is designed for outside use. This is indicated by the

letters “W-A” or “W” on the cord’s jacket.

Before using an extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

WARNING:

Keep the extension cord clear of the working

area. Position the cord so that it will not get

caught on lumber, tools or other obstructions

while you are working with a power tool. Failure

to do so can result in serious personal injury.

WARNING:

Check extension cords before each use. If

damaged replace immediately. Never use

product with a damaged cord since touching

the damaged area could cause electrical shock

resulting in serious injury.

ELECTRICAL CONNECTION

This product is powered by a precision built electric motor.

It should be connected to a power supply that is 120 V, AC

only (normal household current), 60 Hz. Do not operate

this product on direct current (DC). A substantial voltage

drop will cause a loss of power and the motor will overheat.

If the saw does not operate when plugged into an outlet,

double check the power supply.

SPEED AND WIRING

The no-load speed of this tool is approximately 3,450 rpm.

This speed is not constant and decreases under a load or

with lower voltage. For voltage, the wiring in a shop is as

important as the motor’s horsepower rating. A line intended

only for lights cannot properly carry a power tool motor. Wire

that is heavy enough for a short distance will be too light for

a greater distance. A line that can support one power tool

may not be able to support two or three tools.

GROUNDING INSTRUCTIONS

This product must be grounded. In the event of a malfunction

or breakdown, grounding provides a path of least resistance

for electric current to reduce the risk of electric shock. This

tool is equipped with an electric cord having an equipment-

grounding conductor and a grounding plug. The plug must be

plugged into a matching outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet,

have the proper outlet installed by a qualified electrician.

WARNING:

Improper connection of the grounding plug can

result in a risk of electric shock. When repair

or replacement of the cord is required, do not

connect the grounding wire to either flat blade

terminal. The wire with insulation having an

outer surface that is green with or without yellow

stripes is the grounding wire.

Check with a qualified electrician or service personnel if the

grounding instructions are not completely understood, or if

in doubt as to whether the tool is properly grounded.

Repair or replace a damaged or worn cord immediately.

This product is for use on a nominal 120 volt circuit and has

a grounding plug similar to the plug illustrated in figure 1.

Only connect the product to an outlet having the same

configuration as the plug. Do not use an adapter with this

product.

Fig. 1

GROUNDING

120 V GROUNDED

OUTLET

8 - English

ELECTRICAL

WARNING:

To prevent possible electrical hazards, have a

qualified electrician check the line if you are not

certain that it is properly wired.

CHANGING MOTOR VOLTAGE

See Figures 2 - 4.

WARNING:

Electric shock can kill. To reduce the risk of

serious personal injury, never connect plug

to power source until all assembly steps are

completed.

NOTE: The table saw is prewired at the factory for 120 V,

60 Hz. Use the following procedures to change motor voltage

from 120 V to 240 V. This is an optional procedure to be

completed after the saw has been fully assembled.

 Unplug the saw.

 Remove the 6 screws that secure the rear panel of the

saw. Remove the panel.

 Lower the motor to its lowest point.

 Located on the top of the motor is the junction box.

Remove the phillips screw at the back of the junction

box then lift off the cover.

 Remove and discard the electrical tape from the wire

connectors. Remove wire connectors.

 Reconnect the leads.

 Reinstall the wire connectors and wrap each wire with

two layers of new UL listed electrical tape.

 Recheck your wiring with the wiring diagrams.

 Reinstall the junction box cover using the phillips screw.

 Cut off the 120 volt power cord plug and replace it with

a 3-prong 240 volt, 15 amp. UL listed plug.

 Connect the power cord white and black leads,

respectively, to the “hot” plug blade terminals. Connect

the power cord green grounding wire to the plug ground

prong terminal.

 Reinstall the rear panel.

 Plug your table saw into a 220-240 V, 15 amp., 3-prong

receptacle. Make certain the receptacle is connected to

a 240 V, AC power supply through a 240 V branch circuit

having at least a 15 amp capacity and protected by a

15 amp time-delay fuse or circuit breaker.

Fig. 4

BLACK WHITEGREEN

L1

L2

G

1

2 3

4

RED BLACK

WHITE

YELLOW

240V

Fig. 3

GROUNDING

COVER OF

GROUNDED

OUTLET BOX

L2

L1

G

1

3

2

4

RED BLACK

BLACK

WHITE

WHITEGREEN

YELLOW

FOR USE WITH 220-240 VOLT

Fig. 2

9 - English

GLOSSARY OF TERMS

Pilot Hole (drill presses and scroll saws)

A small hole drilled in a workpiece that serves as a guide

for drilling large holes accurately or for insertion of a scroll

saw blade.

Push Blocks (jointer planers)

Device used to feed the workpiece over the jointer planer

cutterhead during any operation. This aid helps keep the

operator’s hands well away from the cutterhead.

Push Blocks and Push Sticks (table saws)

Devices used to feed the workpiece through the saw blade

during cutting operations. When making a narrow rip cut

without a jig or similar cutting aid, always use a push stick

(not a push block). A push block can be used for narrow

ripping operations, if a jig or similar cutting aid is used.

These aids help keep the operator’s hands well away from

the blade.

Rabbet

A non-through cut positioned on the end or edge of the

workpiece which produces a square, two-sided notch or

trough in the workpiece.

Resaw (table saws and band saws)

A cutting operation to reduce the thickness of the workpiece

to make thinner pieces.

Resin

A sticky, sap-based substance that has hardened.

Revolutions Per Minute (RPM)

The number of turns completed by a spinning object in one

minute.

Ripping or Rip Cut (table saws)

A cutting operation along the length of the workpiece and

typically in the direction of the grain.

Riving Knife/Spreader/Splitter (table saws)

A metal piece, slightly thinner than the blade, which helps

keep the kerf open and also helps to prevent kickback.

Saw Blade Path

The area over, under, behind, or in front of the blade. As it

applies to the workpiece, that area which will be or has been

cut by the blade.

Snipe (planers)

Depression made at either end of a workpiece by cutter

blades when the workpiece is not properly supported.

Taper Cut

A cut where the material being cut has a different width at

the beginning of the cut from the end.

Through Sawing

Any cutting operation where the blade extends completely

through the thickness of the workpiece. This type of cut will

separate a single workpiece into two pieces.

Workpiece or Material

The item on which the operation is being done.

Worktable

Surface where the workpiece rests while performing a

cutting, drilling, planing, or sanding operation.

Anti-Kickback Pawls (radial arm and table saws)

A device which, when properly installed and maintained,

is designed to stop the workpiece from being kicked back

toward the front of the saw during a ripping operation.

Arbor

The shaft on which a blade or cutting tool is mounted.

Bevel Cut

A cutting operation made with the blade at any angle other

than 90° to the table surface.

Chamfer

A cut removing a wedge from a block so the end (or part of

the end) is angled rather than at 90°.

Compound Cut

A cross cut made with both a miter and a bevel angle.

Cross Cut

A cutting or shaping operation made across the grain or the

width of the workpiece.

Cutter Head (planers and jointer planers)

A rotating cutterhead with adjustable blades or knives. The

blades or knives remove material from the workpiece.

Dado Cut (table saws and compound sliding miter saws)

A non-through cut which produces a square, three-sided

notch or trough in the workpiece.

Featherboard (table saws)

A device used to help control the workpiece by guiding

it securely against the table or fence during any ripping

operation.

FPM or SPM

Feet per minute (or strokes per minute), used in reference

to blade movement.

Freehand

Performing a cut without the workpiece being guided by a

fence, miter fence, or other aids.

Gum

A sticky, sap-based residue from wood products.

Heel

Alignment of the blade to the fence.

Kerf

The material removed by the blade in a through cut or the

slot produced by the blade in a non-through or partial cut.

Kickback

A hazard that can occur when the blade binds or stalls,

throwing the workpiece in the direction of the spinning blade.

Miter Cut

A cutting operation made with the workpiece at any angle

to the blade other than 90°.

Non-Through Cuts (table saws and compound sliding

miter saws)

Any cutting operation where the blade does not extend

completely through the thickness of the workpiece. This is a

cut where the blade will not cut the workpiece into two pieces.

10 - English

FEATURES

PRODUCT SPECIFICATIONS

Blade Arbor ...............................................................5/8 in.

Blade Diameter ...........................................................10 in.

Blade Tilt ..................................................................0˚ - 45˚

Rating ............................ 120/240 V ~, 13/6.5 Amps, 60 Hz

No Load Speed .....................................3,450 r/min. (RPM)

Cutting Depth at 0º: ............................................... 3-1/4 in.

Cutting Depth at 45º: ............................................. 2-1/4 in.

45

Fig. 5

MITER

GAUGE

TABLE

EXTENSION

MITER

GAUGE

GROOVE

SAW

BLADE

BLADE GUARD

ASSEMBLY

FRONT

RAIL

RIP FENCE

SCALE

LOCKING

HANDLE

SWITCH

ASSEMBLY

BEVEL

ADJUSTING

HANDWHEEL

BEVEL

LOCK KNOB

HEIGHT

LOCK

KNOB

BEVEL

SCALE

RIP

FENCE

RIVING KNIFE

RIP FENCE

STORAGE

BRACKETS

ANTI-KICKBACK

PAWLS

HEIGHT

ADJUSTING

HANDWHEEL

BLADE AND

WRENCH

STORAGE

MITER GAUGE

STORAGE

PUSH

STICK

MITER

GAUGE

GROOVE

11 - English

FEATURES

KNOW YOUR TABLE SAW

See Figure 5.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

ANTI-KICKBACK PAWLS - Kickback is a hazard in which

the workpiece is thrown back toward the operator. The teeth

on the removable anti-kickback pawls point away from the

workpiece. If the workpiece should be pulled back toward

the operator, the teeth dig into the wood to help prevent or

reduce the possibility of kickback.

BEVEL ADJUSTING HANDWHEEL/BEVEL LOCK KNOB -

The bevel adjusting handwheel, located on the side of the

cabinet, is used to adjust the bevel angle of the blade.The

bevel lock knob locks the angle setting of the blade.

BEVEL SCALE - The easy-to-read scale on the front of the

cabinet shows the exact blade angle.

BLADE - For maximum performance, it is recommended

that you use the 10 in. carbide tipped combination blade

provided with your saw. The blade is raised and lowered with

the height adjusting handwheel. Bevel angles are locked with

the bevel lock knob. Additional blade styles of the same high

quality are available for specific operations such as ripping.

Your local dealer can provide you with complete information.

Blade kerf width must be within the limits stamped on the

riving knife.

WARNING:

Do not use blades rated less than the speed of

this tool. Failure to heed this warning could result

in personal injury.

BLADE GUARD - Always keep the removable blade guard

down over the saw blade for through-sawing cuts.

HEIGHT ADJUSTING HANDWHEEL/ HEIGHT LOCK

KNOB - The height adusting handwheel, located on the

front of the cabinet, is used to lower and raise the blade for

height adjustments or blade replacement. The height lock

knob locks the height setting of the blade.

MITER GAUGE - The miter gauge aligns the wood for a cross

cut. The easy-to-read indicator shows the exact angle for a

miter cut, with adjustable stops at 90° and 45°.

MITER GAUGE GROOVES - The miter gauge rides in the

grooves on the saw table.

RIP FENCE - A sturdy metal fence guides the workpiece and

is secured with the locking handle. Grooves run along the

top and sides of the rip fence for use with optional clamps

and accessories.

RIVING KNIFE - A removable metal piece of the blade

guard assembly, slightly thinner than the saw blade, which

helps keep the kerf open and prevent kickback. When in the

through sawing, or “up” position, it is higher than the saw

blade. When in the non-through sawing, or “down” position,

it is below the saw blade teeth.

RIP SCALE - Located on the front rail, the easy-to-read rip

scale provides precise measurements for rip cuts.

SWITCH ASSEMBLY - This saw has an easy access switch

assembly located below the front rail. To lock the switch in

the OFF position, remove the switch key from the switch.

Place the key in a location that is inaccessible to children

and others not qualified to use the tool.

TABLE EXTENSION - Located on each side of the saw table,

the table extensions give the operator additional support

when cutting wide workpieces.

12 - English

FEATURES

WARNING:

ALWAYS make sure your workpiece is not in

contact with the blade before operating the

switch to start the tool. Failure to heed this

warning could cause the workpiece to be kicked

back toward the operator and result in serious

personal injury.

WARNING:

To reduce the risk of accidental starting, always

make sure the switch is in the OFF ( O ) position

before plugging tool into the power source.

OPERATING COMPONENTS

The upper portion of the blade projects up through the table

and is surrounded by an insert called the throat plate. The

height of the blade is set with a handwheel on the front of the

cabinet. Detailed instructions are provided in the Operation

section of this manual for the basic cuts: cross cuts, miter

cuts, bevel cuts, and compound cuts.

The rip fence is used to position work for lengthwise cuts.

A scale on the front rail shows the distance between the rip

fence and the blade.

It is very important to use the blade guard assembly for

all through-sawing operations. The blade guard assembly

includes: riving knife, anti-kickback pawls, and blade guard.

SWITCH ASSEMBLY

See Figure 6.

This saw is equipped with a switch assembly that has a

built-in locking feature. This feature is intended to prevent

unauthorized and possible hazardous use by children and

others.

TO TURN YOUR SAW ON:

 With the switch key inserted into the switch, lift the switch

button to turn ON ( l ).

TO TURN YOUR SAW OFF:

 Press the switch button down to turn OFF ( O ).

TO LOCK YOUR SAW:

 Press the switch button down.

 Remove the switch key from the switch and store in a

safe, secure location.

WARNING:

Always remove the switch key when the tool is

not in use and keep it in a safe place. In the event

of a power failure, turn the switch OFF ( O ) and

remove the key. This action will prevent the tool

from accidentally starting when power returns.

Fig. 6

SWITCH KEY

REMOVED

SWITCH

OFF

SWITCH

ON

SWITCH

COVER

NOTE: For clarity, the cover is not shown

in the illustrations below.

NOTE: The cover does not need to be removed

to remove the switch key.

13 - English

TOOLS NEEDED

The following tools (not included or drawn to scale) are needed for assembly and adjustments:

Fig. 7

FRAMING SQUARE

PHILLIPS

SCREWDRIVER

FLATHEAD

SCREWDRIVER

WRENCH

4 mm, 8 mm, 10 mm, 13 mm, 14 mm

SOCKET WRENCH

(8 mm, 13 mm SOCKET)

C-CLAMPS

COMBINATION

SQUARE

14 - English

LOOSE PARTS

Fig. 8

The following items are included with the table saw:

A. Blade Guard .............................................................. 1

B. Anti-Kickback Pawls ................................................. 1

C. Miter Gauge ............................................................... 1

D. Rip Fence .................................................................. 1

E. Height Adjusting Handwheel, Washer, and Knob ..... 1

F. Bevel Adjusting Handwheel, Washer, and Knob ....... 1

G. Push Stick ................................................................. 1

H. Blade Wrench, open end ........................................... 1

I. Blade Wrench, closed end ........................................ 1

J. Hex Keys (3 mm, 4 mm, 5 mm, 6 mm, 8 mm)........... 1

K. Rear Rail .................................................................... 2

L. Front Rail ................................................................... 2

M. Rail Connector Bar .................................................... 3

N. Table Extensions ....................................................... 2

O. Spreader Bar ............................................................. 1

P. Dust Chute ................................................................ 1

Q. Throat Plate ............................................................... 1

R. Front End Cap (left and right) .................................... 2

S. Back End Cap (left and right) .................................... 2

Not shown:

T. Fastener Pack - Large (contents noted on pack) ...... 1

U. Fastener Pack - Small (contents noted on pack) ...... 1

V. Caster Fastener Bag - Small ..................................... 1

A

R

S

O

B

P

C

J

D

K

Q

E, F

L

M

G

N

L

H

I

15 - English

LOOSE PARTS

A. Leg Stand Side Sections ........................................... 2

B. Leg Stand Front and Back ......................................... 2

C. Outer Corners ............................................................ 4

D. Caster Assembly........................................................ 1

E. Center Support .......................................................... 1

Fig. 9

A

H

B

I

C

D

E

F

G

F. Rear Axle Assembly ................................................... 1

G. Front Axle .................................................................. 1

H. Rip Fence Storage Brackets ...................................... 2

I. Foot ........................................................................... 4

16 - English

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully lift the saw from the carton and place on a level

work surface.

NOTE: This tool is heavy. To avoid back injury, keep your

knees bent and lift with your legs, not your back, and get

help when needed.

WARNING:

Do not use this product if any parts on the

Loose Parts List are already assembled to

your product when you unpack it. Parts on this

list are not assembled to the product by the

manufacturer and require customer installation.

Use of a product that may have been improperly

assembled could result in serious personal injury.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the tool.

NOTE: A box containing some of the Loose Parts is

inside the saw cabinet. Also, remove the foam block from

between the saw’s housing and the motor.

 The saw is factory set for accurate cutting. After assembling

it, check for accuracy. If shipping has influenced the

settings, refer to specific procedures explained in this

manual.

 If any parts are damaged or missing, please call

1-866-539-1710 for assistance.

WARNING:

If any parts are damaged or missing, do not

operate this tool until the parts are replaced. Use

of this product with damaged or missing parts

could result in serious personal injury.

WARNING:

Do not attempt to modify this tool or create

accessories not recommended for use with this

tool. Any such alteration or modification is misuse

and could result in a hazardous condition leading

to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly

is complete. Failure to comply could result in

accidental starting and possible serious personal

injury.

WARNING:

Do not lift the saw without help. Hold it close

to your body. Keep your knees bent and lift

with your legs, not your back. Ignoring these

precautions can result in back injury.

WARNING:

Never stand directly in line with the blade or allow

hands to come closer than 3 in. to the blade. Do

not reach over or across the blade. Failure to

heed this warning can result in serious personal

injury.

WARNING:

To avoid serious personal injury, never operate

the saw if it is not mounted to the supplied leg

stand. NEVER operate the saw on the floor.

17 - English

ASSEMBLY

TABLE

EXTENSION

TABLE

EXTENSION

BOARDS

FLAT

WASHER

LOCK

WASHER

BOLT

SAW

TABLE

SAW

TABLE

LEG STAND

SECTION

OUTER

CORNER

Fig. 10

Fig. 11

Fig. 12

INSTALLING THE TABLE EXTENSIONS

See Figures 10 - 11.

NOTE: It is helpful to place two inch-thick boards on the floor

before lifting the saw table and motor housing from the box.

This will make it easier to assemble parts, and to move the

saw and set it upright.

Lift the saw table and motor housing from the box and

position it on the boards as shown.

Loosen the plastic wrap from the table and lift each side

to remove the wrapping.

From the large fastener pack, locate the following parts:

6 Bolts (M10 x 25)

6 Lock washers (M10)

6 Flat washers (M10)

With the table saw in the upside down position, place a

table extension against the table top, on the same side as

the power cord. The larger holes in the extension should

be aligned with the holes in the saw table.

Make sure the edges of the table extensions are aligned

with the edges of the table.

Insert a lock washer and flat washer over a bolt. Thread

the bolt into the holes in the table extension and saw

table. Repeat for the two remaining holes.

 Repeat above step on the other table extension.

Using an 8 mm socket, tighten the socket head bolts. Do

not tighten completely.

ASSEMBLING THE LEG STAND

See Figure 12.

Locate the following parts:

4 Leg stand sections

4 Outer corners

From the small fastener pack, locate the following parts:

24 Bolts (M6 x 10)

Place an outer corner outside a leg stand section.

NOTE: The top of the outer corner has a bent tab and

hole for assembly to the saw cabinet.

Insert a bolt into each of the three holes and finger tighten.

Repeat with remaining corners and leg stand sections.

Using a 4 mm hex key, tighten all bolts securely.

NOTE: The front of the stand is the section with the

English WARNING label attached.

18 - English

ASSEMBLY

ASSEMBLING THE LEG STAND ONTO THE

SAW CABINET

See Figures 13 - 14.

WARNING:

Only install the dust chute when using a four

inch dust collection system. Failure to heed this

warning could result in serious personal injury or

death. Clean saw dust from the cabinet regularly.

NOTE: Make sure the foam block has been removed before

installing the dust chute.

Place the dust chute on top of the saw cabinet. The word

“FRONT” and the arrow should align with front panel of

the saw and the registration ridges should align with the

grooves.

Place the assembled leg stand over the dust chute as

shown.

Locate the following from the small fastener pack:

4 Flat washers

4 Lock washers

4 Bolts

Slide a lock washer and a flat washer over each bolt.

Thread a bolt into each of the 4 holes at the corners of

the leg stand.

Using a 6mm hex key, securely tighten the bolts.

ASSEMBLING THE CASTER SET

See Figures 15 - 16.

Remove the bolts and nuts from the caster assembly and

the front axle assembly.

NOTE: Use a 13 mm wrench and a 14 mm wrench for the

nuts and the bolts.

Attach the caster to the front axle by sliding the bolt

through the holes and placing the nut over the bolt.

Securely tighten the nut.

Remove the bolts and nuts from the rear and front axle

assemblies.

NOTE: Use a 6 mm hex wrench to hold the bolt and a

13 mm wrench to loosen the nut.

Position the front and rear axles as shown.

Attach the center support to the front axle assembly.

Slide the bolt through the hole in the axle center piece

and thread the nut over the bolt. Tighten the nut.

Attach the center support to the rear axle.

Fig. 13

Fig. 15

Fig. 16

DUST CHUTE

FLAT

WASHER

CASTER

REAR AXLE

ASSEMBLY

FRONT AXLE

ASSEMBLY

FRONT AXLE

ASSEMBLY

NUT

LOCK

WASHER

CENTER

SUPPORT

BOLT

Fig. 14

19 - English

ASSEMBLY

INSTALLING THE CASTER SET TO THE LEG

STAND

See Figure 17.

Slide the caster set into the leg stand, aligning the holes

in the caster assembly with the holes in the leg stand.

 NOTE: Position the pedal as shown, so that it will be on

the left of the saw when the saw is upright.

Locate the following from the small fastener pack:

 8 Bolts (M8 x 16)

Insert the bolts into the holes in the leg stand and through

the holes in each caster.

Using a 5 mm hex key, securely tighten the bolts.

Position the feet on the stand by pressing them into place.

INSTALLING RIP FENCE STORAGE BRACKETS

See Figure 18.

Remove the pre-installed bolt and nut from each bracket.

Insert a bolt through the hole in each bracket, aligning it

as shown with the hole in the stand.

Thread the nut over the bolt. Using a 5 mm hex key,

securely tighten each bolt.

SETTING THE SAW UPRIGHT

See Figure 19.

NOTE: The saw is heavy and requires several people for

this procedure.

 Tilt the saw until it rests on the back side of the cabinet.

 Raise saw carefully until it sits upright.

 To raise the saw table, step down on the pedal until it

locks.

 Roll the table saw to the desired location making sure

the surface is firm and level.

 Pull up on the pedal to slowly lower the table saw.

Fig. 18

Fig. 19

SOCKET

HEAD BOLT

CASTER

ASSEMBLY

BOLT

BRACKET

NUT

PEDAL

FEET

Fig. 17

TO LOWER

20 - English

ASSEMBLY

Fig. 20

INSTALLING THE HEIGHT ADJUSTING

HANDWHEEL

See Figure 20.

NOTE: The height adjusting handwheel knob and the bevel

adjusting handwheel knob act as locks. To lock the wheel for

operation, turn the knob clockwise until it is securely tightened.

 Slide the handwheel over the bolt above the bevel adjustment

scale on the front of the saw.

 Slide the washer over the bolt.

 Screw the knob securely onto the bolt.

INSTALLING THE BEVEL ADJUSTING

HANDWHEEL

See Figure 21.

 Slide the bevel adjusting handwheel over the bolt on the

side of the saw.

 Slide the washer over the bolt.

 Screw the knob securely onto the bolt.

ACCESSORY STORAGE

See Figure 22.

Storage for the blade, blade wrench and miter gauge is

located on the side of the saw. The miter gauge may be

stored by sliding it into the slots.

The push stick contains a magnet. When not in use, the push

stick may be stored at a convenient location on the saw.

HEIGHT

ADJUSTING

HANDWHEEL

BEVEL

ADJUSTING

HANDWHEEL

BOLT

KNOB

WASHER

KNOB

Fig. 21

Fig. 22

MITER GAUGE

STORAGE

BLADE AND

WRENCH

STORAGE

La page charge ...

RIDGID R692BBN Manuel utilisateur

RIDGID R692BBN Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents