Frigidaire CFEF2422RS Manuel utilisateur

Marque: Frigidaire

Modèle: CFEF2422RS

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

CFEF2411RW

Electric Range

All about the

of your

www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352

Use & Care

808575803 Rev C (March 2015)

TABLE OF CONTENTS

Important Safety Instructions . . . . . . . . . . . . . . . . . 3

Before Setting Surface Controls . . . . . . . . . . . . . . . 8

Setting Surface Controls . . . . . . . . . . . . . . . . . . . . 11

Before Setting Oven Controls . . . . . . . . . . . . . . . . 12

Setting Oven Controls . . . . . . . . . . . . . . . . . . . . . . 13

Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 22

Before You Call . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Need Help? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . .2

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . 3

Before Setting Surface Controls. . . . . . . . . . . . . . . . . . 8

Setting Surface Controls . . . . . . . . . . . . . . . . . . . . . . 11

Before Setting Oven Controls . . . . . . . . . . . . . . . . . . . 12

Setting Oven Controls . . . . . . . . . . . . . . . . . . . . . . . . . 13

Setting Bake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Setting Broil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Setting Convection Bake . . . . . . . . . . . . . . . . . . . . . .18

Setting Roast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Setting Convection Broil . . . . . . . . . . . . . . . . . . . . . .21

Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Removing and Replacing the Oven Door . . . . . . . . .27

Before You Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Need Help?

Visit the Frigidaire web site at www.frigidaire.com

Before you call for service, there are a few things you can

do to help us serve you better.

Read this Use & Care Guide

This manual contains instructions to help you use and

maintain your appliance properly.

If You Received a Damaged Appliance...

Immediately contact the dealer (or builder) that sold you the

appliance.

Save Time and Money

Check “Solutions to Common Problems:” on page 30. This

section helps step you through some common problems

that might occur.

If you do need service, help is only a phone call away. Call

Frigidaire customer services at 1-800-944-9044.

Product Registration

Registering your product with Frigidaire enhances our

ability to serve you. You can register online at http://

www.frigidaire.com or by dropping your product registra-

tion card in the mail.

Record model and serial numbers here

Purchase Date: _______________________________

Frigidaire model number: _______________________

Frigidaire serial number: ________________________

Serial Plate Location

PRODUCT RECORD AND REGISTRATION

Questions?

For toll-free telephone support in the U.S. and Canada call

1-800-944-9044

For online support and Internet production information visit

http://www.frigidaire.com.

Thank you for choosing Frigidaire.

This Use & Care Guide is part of our commitment to

customer satisfaction and product quality throughout the

service life of your new appliance. We view your purchase

as the beginning of a relationship. To ensure our ability to

continue serving you, please use this page to record

important product information.

CAUTIONS AND WARNINGS

Read all instructions before using this appliance.

This manual contains important safety symbols and

instructions. Please pay attention to these symbols

and follow all instructions given.

Do not attempt to install or operate your appliance

until you have read the safety precautions in this

manual. Safety items throughout this manual are

labeled with a WARNING or CAUTION statement

based on the risk type.

DEFINITIONS

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety message that follow this symbol to avoid

possible injury or death.

Indicates a potentially hazardous situation which, if

not avoided, may result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

Indicates installation, operation, maintenance, or

valuable information that is not hazard related.

Indicates a short, informal reference-something

written down to assist the memory or for future refer-

ence.

WARNING

CAUTION

IMPORTANT

NOTE

Storage In or On Appliance—Flammable materials

should not be stored in an oven, near surface

burners, or in the warmer drawer (if equipped). This

includes paper, plastic, and cloth items, such as

cookbooks, plastic ware, and towels, as well as

flammable liquids. Do not store explosives, such as

aerosol cans, on or near the range.

Save these instructions for future use.

WARNING

NOTE

WARNING

Tip Over Hazard

• A child or adult can tip

the range and be killed.

• Verify the anti-tip device

has been installed to floor

or wall.

• Ensure the anti-tip device is

re-engaged to floor or wall when the

range is moved.

• Do not operate the range without the

anti-tip device in place and engaged.

• Failure to follow these instructions can

result in death or serious burns to

children and adults.

Range

leveling

leg

Anti-tip

bracket

To check if the anti-tip bracket is installed

properly, use both arms to grasp the rear edge

of the range back. Carefully attempt to tilt

range forward. When properly installed, the

range should not tilt forward.

Refer to the anti-tip bracket installation instruc-

tions supplied with your range for proper

installation.

IMPORTANT SAFETY INSTRUCTIONS

• Do Not Leave Children Alone - Children should

not be left alone or unattended in the area where

appliance is in use. They should never be

allowed to sit or stand on any part of the appli-

ance, including the storage drawer, lower broiler

drawer, warmer drawer, or lower double oven.

• Stepping, leaning, or sitting on the door or

drawers of this appliance can result in serious

injuries and also cause damage to the appliance.

Do not allow children to climb or play around the

appliance. The weights of a child on an open

over door may cause the appliance to tip,

resulting in serious burns or other injury. An open

drawer when hot may cause burns.

• Never cover any slots, holes, or passages in the

oven bottom or cover an entire oven rack with

materials, such as aluminum foil. Aluminum foil

linings may trap heat, causing a fire hazard.

Important Safety Notice - The California Safe

Drinking Water and Toxic Enforcement Act requires

the governor of California to publish a list of

substances known to cause cancer, birth defects, or

other reproductive harms, and requires businesses

to warn customers of potential exposures to such

substances.

Cold temperatures can damage the electronic

control. When using this appliance for the first time,

or when the appliance has not been used for an

extended period of time, be sure the appliance has

been in temperatures above 32ºF (0ºC) for at least 3

hours before turning on the power to the appliance.

Do not attempt to operate the appliance during a

power failure. If the power fails, always turn off the

unit. If the unit is not turned off and the power

resumes, the appliance will not operate and 12:00

will be displayed. Once the power resumes, reset

the clock and the oven function.

WARNING

IMPORTANT

• When heating fat or grease, watch it closely.

Grease may catch fire if it becomes too hot.

• Do not use water or flour on grease fires.

Smother fire or flame or use dry chemical or

foam-type extinguisher. Cover the fire with a pan

lid or use baking soda.

• Use dry potholders. Moist or damp potholders on

hot surfaces may result in burns from steam. Do

not let potholders touch hot cooking areas. Do

not use towels or other bulky cloths.

• Do Not Heat Unopened Food Containers - Build-

up of pressure may cause container to burst and

result in injury.

• Wear Proper Apparel - Loose-fitting or hanging

garments should never be worn while using the

appliance. Do not let clothing or other flammable

materials contact hot surfaces.

• Do not touch surface heating units or surface

cooking elements, areas near these units or

elements, interior surface of the oven, or the

warmer drawer (if equipped). Surface heating

areas and oven heating elements may be hot

even though they appear cool. Areas near

surface cooking units may become hot enough

to cause burns. During and after use, do not

touch, or let clothing or other flammable

materials touch these areas until they are cool.

These areas may include the cooktop, surfaces

facing the cooktop, oven vent areas, oven door,

and oven window.

• Do not store items of interest to children in the

cabinets above a range. Children climbing on the

range to reach items could be seriously injured.

Do not use oven or warmer drawer (if equipped) for

storage. Never use your appliance as a space

heater to heat or warm the room.

CAUTION

WARNING

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT INSTRUCTIONS FOR USING YOUR

COOKTOP

• Know which knob or key controls each surface

heating area. Place cookware with food on the

cooking area before turning it on. Turn the cooking

area off before removing the cookware.

• Use proper pan size. This appliance is equipped

with one or more surface units of different sizes.

Select cookware with flat bottoms that match the

surface unit heating element. The use of under-

sized cookware may expose a portion of the

heating element to direct contact and may result in

the ignition of clothing or other items. Using the

proper cookware on the cooking zone will improve

efficiency.

• To reduce the risk of burns, ignition of flammable

materials, and spills due to unintentional contact

with the utensil, the utensil handles should be

turned inward and not extend over other cooking

areas.

• Never leave surface elements unattended. Boil-

overs may cause smoking and greasy spills may

ignite. A pan that has boiled dry could be damaged

and may damage the cooktop.

• Improper cookware may break due to sudden

changes in temperature. Check the cookware

manufacturer’s recommendations for cooktop use.

• When you are flaming foods under a ventilating

hood, turn on the fan.

• Glazed Cooking Utensils—Only certain types of

glass, glass/ceramic, ceramic, earthenware, or

other glazed utensils are suitable for cooktop

service without breaking due to the sudden change

in temperature. Check the manufacturer’s recom-

mendations for cooktop use.

• Do Not Use Decorative Surface Burner Covers. If

an element is accidentally turned on, the decora-

tive cover will become hot and possibly melt.

Burns will occur if the hot covers are touched.

Damage may also be done to the cooktop.

• Do not use Searing grill on the cooktop. The

Searing grill is not designed for use on the

cooktop. Doing so may result in a fire.

Read and follow the below instructions and precau-

tions for unpacking, installing, and servicing your

appliance:

• Remove all tape and packaging before using the

appliance. Destroy the carton and plastic bags

after unpacking the appliance. Never allow

children to play with packaging material. Do not

remove the wiring label and other literature

attached to the range. Do not remove model/

serial number plate.

• Proper Installation—Be sure your appliance is

properly installed and grounded by a qualified

technician in accordance with the National Elec-

trical Code ANSI/NFPA No. 70 latest edition and

local electrical code requirements. In Canada,

install in accordance with CSA Standard C22.1,

Canadian Electrical code, Part 1-latest edition,

and local electrical code requirements. Install

only per installation instructions provided in the

literature package for this range.

• User Servicing—Do not repair or replace any

part of the appliance unless specifically recom-

mended in the manuals. All other servicing

should be done only by a qualified technician.

This reduces the risk of personal injury and

damage to the oven.

• Ask your dealer to recommend a qualified techni-

cian and an authorized repair service. Know how

to disconnect the power to the appliance at the

circuit breaker or fuse box in case of an emer-

gency.

• Never modify or alter the construction of an oven

by removing the leveling legs, panels, wire

covers, anti-tip brackets/screws, or any other

part of the oven.

• Remove the oven door from any unused oven if

it is to be stored or discarded.

• Be sure to have an appropriate foam-type fire

extinguisher available, visible, and easily acces-

sible located near the appliance.

IMPORTANT

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT INSTRUCTIONS FOR USING YOUR

OVEN

• Use care when opening oven door, lower oven

door, or warmer drawer (some models). Stand to

the side of the appliance when opening the door of

a hot range. Let hot air or steam escape before

you remove or replace food in the oven.

• Keep oven vent ducts unobstructed. Touching

surfaces in this area when the oven is on may

cause severe burns. Do not place plastic or heat-

sensitive items on or near the oven vent. These

items can melt or ignite.

• Placement of Oven Racks - Always place oven

racks in desired location while oven is cool. If rack

must be moved while oven in hot, do not let

potholder contact hot heating element in oven. Use

potholders and grasp the rack with both hands to

reposition. Do not let potholders contact the hot

heating elements in the oven. Remove all

cookware and utensils before moving the rack.

• Do not use a broiler pan without its insert. Broiler

pans and inserts allow dripping fat to drain away

from the high heat of the broiler. Do not cover the

broiler insert with aluminum foil; exposed fat and

grease could ignite.

• Protective Liners—Do not use aluminum foil to line

oven bottom or any other part of the appliance.

Only use aluminum as recommended for baking if

used as a cover placed on the food. Any other use

of protective liners or aluminum foil may result in a

risk of electric shock or fire or a short circuit.

• Do not cook food on the oven bottom. Always cook

in proper cookware and always use the over racks.

GLASS COOKTOP MODELS

• Do Not Clean or Operate a Broken Cooktop. If cooktop

should break, cleaning solutions and spillovers may

penetrate the broken cooktop and create a risk of

electric shock. Contact a qualified technician immedi-

ately.

• Clean Cooktop Glass with Caution. If a wet sponge or

cloth is used to wipe spills on a hot cooking area, be

careful to avoid a steam burn. Some cleaners can

produce harmful fumes if applied to a hot surface.

• Avoid Scratching the cooktop glass with sharp objects.

IMPORTANT INSTRUCTIONS FOR CLEANING

YOUR OVEN

• Clean the range regularly to keep all parts free of

grease that could catch fire. Pay particular

attention to the area around each surface element.

Do not allow grease to accumulate. Greasy

deposits in the fan could catch fire. Follow the

manufacturer’s instructions for cleaning hoods.

• Always follow the manufacturer’s recommended

directions for use of kitchen cleaners and aerosols.

Be aware that excess residue from cleaners and

aerosols may ignite causing damage and injury.

• Clean ventilating hoods frequently. Grease should

not be allowed to accumulate on the hood or filter.

Follow the manufacturer’s instructions for cleaning

hoods.

• Do not touch a hot oven light bulb with a damp

cloth. Doing so could cause the bulb to break.

Disconnect the appliance or shut off the power to

the appliance before removing and replacing the

bulb.

• Do not clean the oven door gasket. The door

gasket is essential for a good seal. Care should be

taken not to rub, damage, or move the gasket.

• Children should be supervised to ensure that they

do not play with the appliance.

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory,

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervi-

sion or instruction concerning use of the appliance

by a person responsible for their safety.

Before manually cleaning any part of the appliance,

be sure all controls are turned off and the range is

cool. Cleaning a hot oven can cause burns.

CAUTION

IMPORTANT SAFETY INSTRUCTIONS

COIL COOKTOP MODELS

• Make Sure Reflector Pans or Drip Bowls Are in

Place—Absence of these pans or bowls during

cooking may subject wiring or components under-

neath to damage.

• Protective Liners—Do not use aluminum foil to line

surface unit drip bowls, or reflector pans. Only use

aluminum foil as recommended in this manual.

Improper installation of these liners may result in

risk of electric shock, or fire. Improper installation

of these liners may result in risk of electric shock,

or fire.

GROUNDING INSTRUCTIONS

For models factory-equipped with a power cord:

For personal safety, this appliance must be properly

grounded. For maximum safety, the power cord must

be plugged into an electrical outlet that is the correct

voltage, is correctly polarized and properly grounded

in accordance with local codes.

It is the personal responsibility of the consumer to have the

appropriate outlet with the correct, properly grounded wall

receptacle installed by a qualified electrician.

See the installation instructions packaged with this

appliance for complete installation and grounding

instructions.

Do not attempt to operate any part of this appliance

during a power failure. If the power fails, always turn

off the unit. If the unit is not turned off and the power

resumes, some parts of the appliance may begin to

operate again. The clock must be set manually after

the power resumes.

IMPORTANT

Avoid fire hazard or electrical shock. Failure to

follow this warning may cause serious injury, fire, or

death.

Figure 1: Grounding plug and receptacle

Avoid fire hazard or electrical shock. Do not use an

adapter plug, use an extension cord, or remove

grounding prong from the power cord. Failure to

follow this warning may cause serious injury, fire, or

death.

WARNING

240V grounded

wall receptacle

Power supply

cord with 4-prong

grounding plug

WARNING

Using Proper Cookware

Check for flatness by rotating a ruler across the bottom of

the cookware (Figure 2). Cookware should have flat

bottoms that make good contact with the entire surface

heating element (Figure 3). For detailed information about

the ceramic cooktop, refer to the“Glass Cooktop Cleaning”

on page 25.

Cookware Material Types

The cookware material determines how evenly and quickly

heat is transferred from the surface element to the pan

bottom. The most popular materials available are:

Aluminum - Excellent heat conductor. Some types of food

will cause it to darken (Anodized aluminum cookware

resists staining and pitting). If aluminum pans slide across

the ceramic cooktop, they may leave metal marks which will

resemble scratches. Remove these marks immediately.

Copper - Excellent heat conductor but discolors easily (See

Aluminum).

Stainless - Slow heat conductor with uneven cooking

results. Is durable, easy to clean and resists staining.

Cast Iron - A slow heat conductor however will retain heat

very well. Cooks evenly once cooking temperature is

reached. Not recommended for use on ceramic cooktops.

Porcelain-enamel on metal - Heating characteristics will

vary depending on base material. Porcelain-enamel coating

must be smooth to avoid scratching ceramic cooktops.

Glass - Slow heat conductor. Not recommended for ceramic

cooktop surfaces because it may scratch the glass.

The size and type of

cookware used will influ-

ence the radiant element

power level setting

needed for best cooking

results. Be sure to follow

the recommendations for

using proper cookware

as illustrated in Figure 2

and Figure 3.

Figure 2: Testing cookware

Figure 3: Proper cookware placement

• Flat bottom and straight

sides.

• Tight ﬁtting lids.

• Weight of handle does

not tilt pan. Pan is well

balanced

• Pan sizes match the

amount of food to be

prepared and the size

of the surface element.

• Made of material that

conducts heat well.

• Easy to clean.

• Always match pot

diameter to element

size.

• Curved and warped pans.

• Cookware larger than

cooking area marked on

cooktop by more than

one-half inch or 12mm.

• Heavy handle tilts pan.

• Pan is smaller than the

heating area marked on

cooktop.

Do not place empty aluminum, glass or porcelain-enamel

coated cookware on the ceramic cooktop! The melting

point of cookware made with these materials may be

reached quickly especially if left empty, and they may

bond to the ceramic cooktop. If the cookware melts it will

damage the cooktop! Be sure to follow all the cookware

manufacturer’s suggestions when using any type of

cookware on the ceramic cooktop.

The cooktop should not be used as a cutting board or

work surface. Dropping heavy or hard objects on the

cooktop may crack it. Pans with rough bottoms may

scratch the cooktop surface. Placing food directly on the

smoothtop surface (without cooking utensil) is not recom-

mended as difficult cleaning will result and foods may

smoke and cause potential fire hazard. Never use the

griddle or similar cooking sheet on the ceramic glass

cooktop.

IMPORTANT

CAUTION

BEFORE SETTING SURFACE CONTROLS

About Surface Elements

For efficient cooking, turn off the element several minutes

before cooking is complete. This will allow residual heat to

complete the cooking process.

The type and size of cookware, the number of surface

elements in use and their settings are all factors that will

affect the amount of heat that will spread to areas beyond

the surface elements. The areas surrounding the elements

may become hot enough to cause burns.

About the Ceramic Glass Cooktop

The ceramic cooktop has radiant surface elements located

below the surface of the glass. The design of the ceramic

cooktop outlines the area of the surface element under-

neath. Be sure to match the pan size with the diameter of

the element outline on the cooktop and only flat-bottomed

cookware should be used.

The element temperature rises gradually and evenly. As the

temperature rises, the element will glow red. To maintain

the selected setting the element will cycle on and off. The

heating element retains enough heat to provide a uniform

and consistent heat during the off cycle.

Hot Surface Indicator Light

Your appliance is equipped with a radiant surface control

indicator light, which is located on the control panel

(Figure 4).

The hot surface indicator light will glow when any surface

cooking area heats up and will remain on until the glass

cooktop has cooled to a moderate level (Figure 5).

Radiant elements have a limiter that allows the element to

cycle on and off, even at the HI setting. This helps to

prevent damage to the ceramic smooth top. Cycling at the

HI setting is normal and can occur if the cookware is too

small for the radiant element or if the cookware bottom is

not flat.

For detailed information about the ceramic cooktop, refer

to the “Glass Cooktop Cleaning” on page 25.

Do not allow aluminum foil, or any material that can melt,

to make contact with the ceramic glass cooktop. If these

items melt on the cooktop, they will damage the ceramic

cooktop.

NOTE

CAUTION

Figure 4: Hot surface indicator light location

Figure 5: Cooking zone distribution (ceramic glass

cooktop)

The glass surface may still be hot and burns may occur if

the glass surface is touched before the indicator light has

turned off.

180 mm

140 mm

CAUTION

BEFORE SETTING SURFACE CONTROLS

Home Canning

‘

Be sure to read and observe all the following points when

home canning with your appliance. Check with the USDA

(United States Department of Agriculture) Web site and be

sure to read all the information they have available as well

as follow their recommendations for home canning proce-

dures.

• Use only quality flat bottom canners when home

canning. Use a straight-edge to check canner bottom.

• Use only a completely flat bottom canner with no ridges

that radiate from the bottom center when home

canning. Heat is spread more evenly when the bottom

surface is flat.

• Make sure the diameter of the canner does not exceed

1 inch beyond the surface element markings or burner.

It is recommended to use smaller diameter canners on

electric coil and ceramic glass cooktops and to center

canners on the burner grates.

• Start with hot tap water to bring water to boil more

quickly.

• Use the highest heat seating when first bringing the

water to a boil. Once boiling is achieved, reduce heat to

lowest possible setting to maintain that boil.

• Use tested recipes and follow instructions carefully.

Check with your local Cooperative Agricultural

Extension Service or a manufacturer of glass jars for

the latest canning information.

• It is best to can small amounts and light loads.

• Do not leave water bath or pressure canners on high

heat for an extended amount of time.

• Alternate surface units between each batch to allow the

units and surrounding surfaces to cool down. Try to

avoid canning on the same burner unit all day.

Canning can generate large amounts of steam. Use

extreme caution to prevent burns. Always raise the lid to

vent steam away from you. Safe canning requires that

harmful micro-organisms are destroyed and the jars are

sealed completely. When canning in a water bath canner,

a gentle but steady boil must be maintained continuously

for the required time.

CAUTION

Surface Cooking Elements and Settings

The cooktop has four single radiant or coil surface

elements, depending upon your appliance.

The size and type of utensil used, and the amount and type

of food being cooked will influence the surface element

power level setting needed for best cooking results.Use

Table 1 to determine the correct setting for the type of food

you are preparing.

To Operate the Surface Elements:

1. Place correctly sized cookware on the radiant or coil

surface element.

2. Push in and turn the surface control knob in either

direction to the desired setting (Figure 7). Start most

cooking operations on a higher setting and then turn to

a lower setting to finish cooking. Each surface element

provides a constant amount of heat at each setting. A

glowing red surface heating area extending beyond the

bottom edge of the cookware indicates the cookware is

too small for the surface heating area.

3. When cooking has completed, turn the surface control

knob to OFF before removing the cookware.

Surface Cooking Tips:

• For efficient cooking, turn off the element several

minutes before cooking is complete. This will allow

residual heat to complete the cooking process.

• The surface Element On indicator lights will glow when

one or more elements are turned on. A quick glance at

these indicator lights when cooking is finished is an

easy check to be sure all surface elements are turned

off.

Figure 6: Surface control knobs

Figure 7: Control knob shown is typical only

Table 1: Recommended settings for surface elements

Setting Type of Cooking

HIGH (HI) Start most foods; bring water to a boil and

pan broiling.

MEDIUM

HIGH (8-10)

Continue a rapid boil; frying, deep fat

frying

MEDIUM (6) Maintain a slow boil; thicken sauces and

gravies; steaming vegetables

Medium

LOW (2-4)

Keep foods cooking; poaching and

stewing

LOW (LO) Keep warm, melting and simmering

Radiant surface elements may appear to have cooled

after they have been turned off. The indicator light will

turn on and will continue to glow until the glass cooktop

has cooled down to a moderate level. The glass surface

may still be hot and burns may occur if the glass surface

is touched before the indicator light has turned off.

Do not allow aluminum foil, empty glass/porcelain

cookware or any material that can melt to make contact

with the ceramic cooktop. If these items melt on the

cooktop they may damage the ceramic cooktop.

Do not place plastic items such as salt and pepper

shakers, spoon holders or plastic wrappings on top of the

range when it is in use. These items could melt or ignite.

Potholders, towels or wooden spoons could catch fire if

placed too close to the surface elements.

CAUTION

SETTING SURFACE CONTROLS

Oven Vent Location

The oven vent is located under the control panel. When the

oven is on, warm air passes through this vent. This venting

is necessary for proper air circulation in the oven and good

baking results. Do not block oven vent. Never close off the

openings with aluminum foil or any other material. Steam or

moisture may appear near the oven vent. This is normal.

The Cooling Fan

The cooling fan operates during cooking. Air is expelled

through the vents between the oven door and the control

panel, as shown in Figure 8.

Removing, Replacing, and Arranging Racks

This appliance comes with two flat racks.

To arrange - Always arrange the oven racks when the oven

is cool (prior to operating the oven).

To remove - Pull the oven rack straight forward until it

reaches the stop position. Lift up front of oven rack slightly

and slide out.

To replace - Place the oven rack on the rack guides on both

sides of oven walls. Tilt the front of oven rack upward

slightly and slide the oven rack back into place. Be sure

oven racks are level before using.

Flat Oven Rack

Air Circulation in the Oven

The rack has a special shape in the rear which helps with

the heat circulation.

Do not push the baking tray all the way to the back wall of

the cavity. This prevents the heat from circulating around

the tray. The food may be burnt, especially in the rear part

of the tray.

For best air circulation when baking, allow a space of 2

inches (5 cm) around the cookware for proper air circula-

tion. Be sure pans and cookware do not touch each other,

the oven door, sides, or back of the oven cavity.

Hot air must be able to circulate around cookware for even

heat to reach the food.

Figure 8: Oven vent location

Always use pot holders or oven mitts when using the

oven. When cooking, the oven interior and exterior, oven

racks, and cooktop will become very hot which can cause

burns.

Figure 9: Removing, replacing, and arranging racks

CAUTION

Protective Liners — Do not use aluminum foil to line the

oven bottom. Only use aluminum foil as recommended in

this manual. Improper installation of these liners may

result in risk of electric shock or fire.

Figure 10: Flat oven rack

WARNING

BEFORE SETTING OVEN CONTROLS

Oven Control Features

1. Up / Down arrows - Use to adjust and set the appli-

ance’s timer functionality.

2. Timer on-off - Use to set or cancel the minute timer.

The minute timer does not start or stop any cooking

function.

3. Oven temp knob - Use to select the desired cooking

temperature.

4. Oven indicator light - Glows each time the oven cycles

on to maintain the set oven temperature.

5. Oven light - Use this switch to turn the internal oven

light on or off.

6. Bake - Use to enter the normal baking mode tempera-

ture and start a normal baking function.

7. Broil - Use to set the broil function.

8. Roast- Use to select the roasting function, best for

cooking tender cuts of beef, lamb, pork, and poultry.

9. Conv bake - Use to select convection baking, which is

used to obtain the best culinary results when baking

with multiple pans and racks at any temperature.

10. Conv broil - Use to select the convection broil function,

best for thicker cuts of meat, fish and poultry. Convec-

tion broiling gently browns the exterior and seals in the

juices.

Operating the Oven Light

Setting the Time

You must set the time before you operate the oven. When

you connect the appliance to the electrical supply or after a

power outage, the display flashes automatically.

To set the time:

1. Press timer on-off. The timer activate symbol will come

on.

2. Use and to set the correct time of day. After

approximately five seconds, the flashing stops and the

display shows the time of day you set.

To change the time:

1. When the appliance is active, press and hold and

at the same time.

2. When the dot between the hour and minutes flashes,

use and to set the new time.

Press the oven light switch located on the

control panel to turn the interior oven light

on and off. The light is located in the rear

of the oven interior. To replace the interior

oven light, see “Replacing the Oven Light”

on page 28.

Figure 11: Oven light switch

On some models, the time of day is a 24-hour clock and

cannot be changed to 12 hours.

NOTE

SETTING OVEN CONTROLS

Timer Functions

This appliance is equipped with three timer options: minute

countdown timer, cook time (dur), and end time (END).

Display Indicators

•A: Duration and End time indicator

•B: Time display

•C: Timer active indicator

•D: Minute timer indicator

To set a timer function:

1. For Duration (dur) and END (end), use the oven temp

and oven mode knobs to set an oven function and

cooking temperature. (This is not necessary for .)

2. Press timer on-off until the desired function option

appears, indicated by the bell symbol, dur, or END, and

starts to flash.

3. Press or to set the desired timer function. The

timer function activates, and the corresponding

indicator will appear in the display. For End and dur, A

will also appear in the display.

4. When the time ends, the function’s indicator on the

display will start flashing and an signal will sound for two

minutes. Press any button to stop the signal.

To cancel the timer function:

1. Press timer on-off until the desired function option

appears.

2. Press and hold and at the same time. The

timer function will go out after several seconds.

To change the acoustic signal:

1. To hear the current signal, press and hold .

2. Repeatedly press to change the signal.

3. Release . The last tone you heard will be the new

signal.

4. Wait five seconds for the setting to be confirmed.

Table 2: Timer Functions

Function Application

Minute Timer ( ) Use to track your cooking times without interfering with the cooking process. The timer

may be set from a minimum time of 1 minute to a maximum of 23 hours and 59 minutes.

Cook Time Duration (dur) Use to set the cooking time of the oven, from 1 minute to 10 hours.

End Time (END) Use to program the oven when to stop cooking, from 1 minute to 10 hours.

Figure 12: Clock display functions

Duration and End time may be used at the same time if

you want the appliance to activate and deactivate auto-

matically. First, set Duration. Then, set End.

ABC D

NOTE

With the Duration and End functions, the appliance will

stop cooking automatically.

When the appliance is disconnected from the outlet or

after a power outage, the signal tone will be set back to

the default tone.

IMPORTANT

NOTE

SETTING OVEN CONTROLS

Setting Bake

Use the bake feature whenever the recipe calls for baking

using normal temperatures.

To set bake:

1. Arrange oven racks while the oven is still cool.

2. Allow oven to preheat for 8-to-10 minutes before

baking. Preheating is not necessary when roasting,

cooking casseroles, or broiling most foods.

3. Turn the oven mode knob to the bake position

(Figure 13).

4. Turn the oven temp knob to the desired temperature

position (Figure 14).

5. To cancel the baking function, turn the oven mode and

oven temp knobs to the OFF positions.

Always use pot holders or oven mitts when using the

oven. When cooking the oven interior, oven racks,

and cooktop will become very hot which can cause

burns.

Do not bake foods directly on the oven bottom. To

avoid damaging the oven interior and surfaces,

always bake foods in the oven using bakeware posi-

tioned on an oven rack.

Figure 13: Oven mode knob

CAUTION

Figure 14: Oven temp knob

Incorrect operation of the appliance or defective compo-

nents can cause dangerous overheating. To prevent this,

this appliance has a safety thermostat which interrupts

the power supply. The appliance activates again automat-

ically when the temperature drops.

Figure 15: Oven rack positions

WARNING

SETTING OVEN CONTROLS

Single Rack Baking

If you choose to use a single rack while cooking, then

radiant baking is preferred.

• For best results when baking with one oven rack, place

racks in positions 2 or 3 (Figure 15).

• When baking using one oven racks, position bakeware

as shown in Figure 16. Allow at least 2 inches (5 cm) of

space between bakeware for proper air circulation.

Multi-Rack Baking

If you choose to use multiple rack while cooking, then

Convection baking is preferred.

• For best results when baking cakes or cookies using

two oven racks, place racks in positions 1 and 3

(Figure 15) and place pans as shown in Figure 17.

• Allow at least 2 inches (5 cm) of space between

bakeware for proper air circulation.

General Baking Tips:

• Preheat the oven 8-10 minutes before baking items like

cookies, biscuits, cakes, and breads.

• Dark or dull pans absorb more heat than shiny

bakeware, resulting in dark or over browning of foods. It

may be necessary to reduce the oven temperature or

cook time to prevent over browning of some foods. Dark

pans are recommended for pies. Shiny pans are recom-

mended for cakes, cookies, and muffins.

• Do not open the oven door too often. Opening the door

will reduce the temperature in the oven.

• Glass bakeware is a slow heat conductor. May require

reducing oven temperature.

Figure 16: Baking with a single rack

For this appliance, single rack radiant bake is the recom-

mended bake function for best results for batter and

dough-based baked goods such as cakes, pastries, and

breads.

The single rack baking image is correct, but it’s also for

presentation purposes. You may also bake with the left

pan in the front and the right pan in the back. Either

position for either pan bakes correctly.

IMPORTANT

NOTE

Figure 17: Baking with multiple levels & racks

When baking using two oven racks, the pans on each

rack must be swapped half way through the cook time for

best results.

IMPORTANT

SETTING OVEN CONTROLS

Setting Broil

Use to cook meats that require direct exposure to radiant

heat for optimum browning results. Position the rack as

suggested in Table 3.

To set broil

1. Arrange the oven rack while oven is still cool. Turn the

oven mode knob to the broil position (Figure 13).

2. Turn the oven temp knob to the desired temperature

position (Figure 14). For optimum results, preheat broil

for 2-to-5 minutes before adding food.

3. Place the insert on the broil pan (if equipped), then

place the food on the broil pan insert (if using a broiler

pan and insert). To purchase a broiling pan and insert,

visit frigidaire.com

4. Place the broiler pan and insert on the oven rack.

Center the broiler pan directly under the broiler element.

Broil on one side until food is browned. Always pull the

oven rack out to the stop position before turning or

removing food. Turn and broil food on the second side.

5. To cancel the broiling function, turn the oven mode and

oven temp knobs to the OFF positions.

Keep the oven door closed when broiling. The escaping

heat could damage appliance knobs and controls.

NOTE

Figure 18: Broil accessories

Should an oven fire occur, keep oven door closed and

turn off the oven. If the fire continues, throw baking soda

on the fire or use a fire extinguisher. Do not put water or

flour on the fire. Flour may be explosive and water can

cause a grease fire to spread and cause personal injury.

The broiler pan and the insert allow grease to drain and

be kept away from the high heat of the broiler. Do not use

the pan without the insert. Do not cover the insert with

aluminum foil; the exposed grease could ignite.

Always use pot holders or oven mitts when using the

oven. When cooking, the oven interior, oven racks, and

cooktop will become very hot which can cause burns.

Searing

Grill

Broiler

Pan

Broiler Pan

& Insert

Broiler

Insert

WARNING

CAUTION

Table 3: Broil recommendations

Food item Rack Position Temperature Cook time in minutes

1st side 2nd side

Doneness

Steak 1” thick 3rd

4th

480°F

7:00

8:00

6:00

7:00

Rare

Medium

Pork Chops 3/4 “thick 3rd or 4th 480°F 8:00 6:00 Well

Chicken - Bone In 3rd 450°F 20:00 10:00 Well

Chicken Boneless 3rd or 4th 450°F 8:00 6:00 Well

Fish 3rd 480°F 13:00 -- Well

Shrimp 3rd 480°F 5:00 -- Well

Hamburger 1” thick 3rd

3rd or 4th

480°F

7:00

9:00

6:00

7:00

Rare

Medium

a.The U.S. Department of Agriculture states, “Rare fresh beef is popular, but you should know that cooking it to only 140°F (60°C) means some food poisoning organisms may

survive.” (Source: Safe Food Book, Your Kitchen Guide, USDA Rev. June 1985.) The lowest temperature recommended by the USDA is 145°F (63°C) for medium rare fresh

beef. For beef medium 160°F, well done 170°F.

SETTING OVEN CONTROLS

Setting Convection Bake

Convection functions use a fan to circulate the oven's heat

uniformly and continuously around the oven (Figure 19).

This improved heat distribution allows for fast, even baking

and browning results. It also gives better baking results

when using two oven racks at the same time. Heated air

flows around the food from all sides, sealing in juices and

flavors. Breads and pastry brown more evenly. Most foods

baked in a standard pan will bake faster and more evenly

with the convection feature. Multiple rack baking may

slightly increase bake time for some foods, but the overall

result is time saved.

Benefits of Convection Bake:

• Superior multiple oven rack performance

• Foods bake more evenly

• Foods can bake up to 25 to 30% faster.

To set convection bake:

1. Arrange oven racks while the oven is still cool.

2. Allow oven to preheat the oven for 8-to-10 minutes

before baking. Preheating is not necessary when

roasting, cooking casseroles, or broiling most foods.

3. Turn the oven mode knob to the conv bake position

(Figure 20).

4. Turn the oven temp knob to the desired temperature

position (Figure 21).

When using convection bake, decrease your normal

cooking times. Adjust the cook time for desired doneness

as needed. Time reductions will vary depending on the

amount and type of food to be cooked.

Be aware that the convection fan will continue to run

after the door is opened. This is normal. Use caution

when reaching inside of the oven. Hot air will be

pushed out of the appliance.

Figure 19: Air movement using convection

IMPORTANT

CAUTION

Always use pot holders or oven mitts when using the

oven. When cooking the oven interior, oven racks,

and cooktop will become very hot which can cause

burns.

Do not bake foods directly on the oven bottom. To

avoid damaging the oven interior and surfaces,

always bake foods in the oven using bakeware posi-

tioned on an oven rack.

Figure 20: Oven mode knob

Figure 21: Oven temp knob

CAUTION

SETTING OVEN CONTROLS

5. To cancel the baking function, turn the oven mode and

oven temp knobs to the OFF positions.

Single Rack Baking

• For best results when baking with one oven rack, place

racks in positions 2 or 3 (Figure 22).

• When baking using one oven rack, position bakeware

as shown in Figure 23. Allow at least 2 inches (5 cm) of

space between bakeware for proper air circulation.

• The single rack baking image is correct, but it’s also for

presentation purposes. You may also bake with the left

pan in the front and the right pan in the back. Either

position for either pan bakes correctly.

• If you choose to use a single rack while cooking, then

radiant baking is preferred. If you choose to use multiple

rack while cooking, then Convection baking is preferred.

Multi-Rack Baking

If you choose to use multiple rack while cooking, then

Convection baking is preferred.

• For best results when baking cakes or cookies using

two oven racks, place racks in positions 1 and 3

(Figure 22) and place pans as shown in Figure 24.

• Allow at least 2 inches (5 cm) of space between

bakeware for proper air circulation.

General Baking Tips:

• When using convection, use bakeware with low sides.

This allows the air to circulate around the food evenly.

• Because most food items will cook faster and more

evenly with the convection feature, it is advisable to

reduce recipe’s recommended temperature by 25° for

best results. Follow the recipe’s instructions using the

minimum recommended cook time.

• When using Conv Bake, cook time reductions may vary

depending on the amount and type of food being

cooked.

• Fully preheat the oven for 8-10 minutes before baking

items like cookies, biscuits and breads.

• Dark or dull pans absorb more heat than shiny

bakeware, resulting in dark or over browning of foods. It

may be necessary to reduce the oven temperature or

cook time to prevent over browning of some foods. Dark

pans are recommended for pies. Shiny pans are recom-

mended for cakes, cookies, and muffins.

• Do not open the oven door too often. Opening the door

will reduce the temperature in the oven.

• Glass bakeware is a slow heat conductor. May require

reducing oven temperature.

Incorrect operation of the appliance or defective compo-

nents can cause dangerous overheating. To prevent this,

this appliance has a safety thermostat which interrupts

the power supply. The appliance must be manually

activated after the temperature drop, restoring the timer.

Figure 22: Oven rack positions

Figure 23: Baking with a single rack

For this appliance, single rack radiant bake is the recom-

mended bake function for best results for batter and

dough-based baked goods such as cakes, pastries, and

breads.

WARNING

IMPORTANT

Figure 24: Baking with multiple levels & racks

When baking using two oven racks, the pans on each

rack must be swapped half way through the cook time for

best results. The top rack should go on the bottom rack

and the bottom to the top.

IMPORTANT

SETTING OVEN CONTROLS

Setting Roast

Use the roast function to roast meats and poultry. Meats

cooked using the roast function will be juicier and poultry

will be crisp on the outside while staying tender and moist

on the inside.

Suggestions for roast:

• The broiler pan will catch grease drippings, and the grid

will help prevent splatters. The roasting rack will hold

the meat.

• Do not cover foods when dry roasting as this will

prevent the meat from browning properly.

• It is not recommended to roast chicken on a roasting

rack. Use a deep pan instead.

• Use a deep pan for fatty food to prevent the oven from

stains that can be permanent.

To set roast:

1. Arrange oven racks while the oven is still cool.

2. Preheat the oven if desired, but preheating is not

necessary when roasting and cooking casseroles.

Preheating is necessary when broiling.

3. Turn the oven mode knob to the roast position

(Figure 25).

4. Turn the oven temp knob to the desired temperature

setting (Figure 26).

5. To cancel the roasting function, turn the oven mode

and oven temp knobs to the OFF positions.

Always use pot holders or oven mitts when using the

oven. When cooking the oven interior, oven racks,

and cooktop will become very hot which can cause

burns.

Do not bake foods directly on the oven bottom. To

avoid damaging the oven interior and surfaces,

always bake foods in the oven using bakeware posi-

tioned on an oven rack.

CAUTION

Figure 25: Oven mode knob

Figure 26: Oven temp knob

Incorrect operation of the appliance or defective compo-

nents can cause dangerous overheating. To prevent this,

this appliance has a safety thermostat which interrupts

the power supply. The appliance must be manually

activated after the temperature drop, restoring the timer.

WARNING

La page charge ...

Frigidaire CFEF2422RS Manuel utilisateur

Marque: Frigidaire

Modèle: CFEF2422RS

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

CFEF2411RW

Télécharger le PDF

rapport

dans d''autres langues

English: Frigidaire CFEF2422RS User manual

Frigidaire CFEF2422RS Manuel utilisateur

Ce manuel convient également à

Frigidaire CFEF2422RS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents