Kenmore C970 Series Manuel utilisateur

Use & Care Guide

English

P/N 318205821A (1009)

Sears Canada Inc., Toronto, Ontario,

Canada M5B 2B8

www.sears.ca

TM

Kenmore Elite

®

Slide-in Electric Range

2

Please carefully read and save these instructions

This Use & Care Manual contains general operating instructions for your appliance and feature information for several

models. Your product may not have all the described features. The graphics shown are representative. The graphics on your

appliance may not look exactly like those shown. Common sense and caution must be practiced when installing, operating

and maintaining any appliance.

Printed in Canada

Serial Plate Location

You will ﬁ nd the model and serial

number printed on the serial plate.

The serial plate is located along the

interior side trim and visible when

the oven door is opened.

Remember to record the serial

number for future reference.

Product Record

In this space below, record the date of purchase, model and

serial number of your product. You will ﬁ nd the model and

serial number printed on the serial plate.

Model No. ______________________________________

Serial No. _______________________________________

Date of purchase ________________________________

Save these instructions and your sales receipt for future

reference.

C970.

Serial Plate Location

Table of Contents

Kenmore Elite Warranty .............................................................2

Product Record .............................................................................2

Serial Plate Location ...................................................................2

IMPORTANT SAFETY INSTRUCTIONS ................................ 3-5

Feature at a Glance ....................................................................6

Before Setting Oven Controls ....................................................7

Surface Cookware Recommendations ......................................8

Before Setting Surface Controls ...........................................9-10

Setting Surface Controls ....................................................... 11-13

Oven Control Functions ............................................................ 14

Getting Started ...........................................................................15

Setting Oven Controls ......................................................... 16-24

Warmer Drawer ...................................................................25-26

User Preferences ........................................................................27

Self-Cleaning Cycle .............................................................28-29

Care & Cleaning ..................................................................30-34

Before You Call ....................................................................35-37

Notes ...........................................................................................38

Protection Agreements ..............................................................39

Sears Service ............................................................................. 40

Kenmore Elite Warranty

When installed, operated and maintained according to all instructions supplied with the product, if this appliance fails due to a

defect in material and workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair.

This warranty applies for only 90 days from the date of purchase if this appliance is ever used for other than private family purposes.

This warranty covers only defects in material and workmanship. Sears will NOT pay for:

1. Cracks in a ceramic glass cooktop that are not a result of thermal shock.

2. Stains and scratches on a ceramic glass cooktop resulting from accident or improper operation or maintenance.

3. Expendable items that can wear out from normal use, including but not limited to ﬁ lters, belts, light bulbs, and bags.

4. A service technician to instruct the user in correct product installation, operation or maintenance.

5. A service technician to clean or maintain this product.

6. Damage to or failure of this product if it is not installed, operated or maintained according to the all instructions

supplied with the product.

7. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

8. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

9. Damage to or failure of parts or systems resulting from unauthorized modiﬁ cations made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer’s sole and exclusive remedy under this limited warranty shall be product repair as provided herein. Implied

warranties, including warranties of merchantability or ﬁ tness for a particular purpose, are limited to one year or the shortest

period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not

allow the exclusion or limitation of incidental or consequential damages, or limitation on the duration of implied warranties

of merchantability or ﬁ tness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States or Canada.

This warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from state to state.

Sears Brands Management Corporation, Hoﬀ man Estates, IL 60179 - Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8

3

• Never modify or alter the construction of an

appliance by removing panels, wire covers or

any other part of the product.

• Remove the oven door from any unused

appliance if it is to be stored or discarded.

Stepping, leaning, sitting or pulling

down on the door of this appliance can result in

serious injuries and may also cause damage to

the appliance. Do not allow children to climb or

play around the appliance.

• Storage on Appliance. Flammable materials

should not be stored near surface units. This

includes paper, plastic and cloth items, such

as cookbooks, plasticware and towels, as well

as ﬂ ammable liquids. Do not store explosives,

such as aerosol cans, on or near the appliance.

Flammable materials may explode and result in

ﬁ re or property damage.

Do not use the ovens for storage.

Do not store items of interest to

children in the cabinets above an appliance.

Children climbing on the appliance to reach items

could be seriously injured.

• Do not leave children alone. Children should

not be left alone or unattended in the area

where an appliance is in use. They should never

be allowed to sit or stand on any part of the

appliance.

• DO NOT TOUCH SURFACE UNITS, AREAS

NEAR THESE SURFACES, OVEN HEATING

ELEMENTS OR INTERIOR SURFACES. Surface

units may be hot even though they are dark in

color. Areas near surface units may become hot

enough to cause burns. During and after use,

do not touch, or let clothing or other ﬂ ammable

materials touch these areas until they have had

suﬃ cient time to cool. Among these areas are

the cooktop, surfaces facing the cooktop, the

oven vent openings and surfaces near these

openings, oven door and window.

• Remove all tape and packaging before using

the appliance. Destroy the carton and plastic

bags after unpacking the appliance. Never

allow children to play with packaging material.

• Proper Installation. Be sure your appliance is

properly installed and grounded by a qualiﬁ ed

technician in accordance with National

Electrical Code ANSI/NFPA No.70 (USA) or CSA

C22.1, PART 1 (Canada)-latest edition and local

code requirements. Install only per installation

instructions provided in the literature package

for this appliance.

• In case of an emergency, know how to

disconnect the electrical power to the appliance

at the circuit breaker or fuse box.

• User Servicing. Do not repair or replace

any part of the appliance unless speciﬁ cally

recommended in the manuals. All other

servicing should be done only by a qualiﬁ ed

technician to reduce the risk of personal injury

and damage to the appliance. Sears Parts &

Repair is the recommended repair service for

this appliance.

This manual contains important safety symbols and instructions. Please pay attention to these

symbols and follow all instructions given.

This symbol will help alert you to situations that may cause serious bodily harm,

death or property damage.

This symbol will help alert you to situations that may cause bodily injury or

property damage.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this appliance.

• All appliances can tip.

• Injury to persons could result.

• Install anti-tip bracket packed with

unit.

• See Installation Instructions.

To reduce the risk of tipping, the

appliance must be secured by

properly installed anti-tip bracket

provided with the appliance. To

check if the bracket is installed

properly; grasp the top rear

of the appliance and carefully

attempt to tilt it forward. Refer

to the Installation Instructions

for proper anti-tip bracket

installation.

4

IMPORTANT SAFETY INSTRUCTIONS

• Wear Proper Apparel. Loose-ﬁ tting or hanging

garments should never be worn while using

the appliance. Do not let clothing or other

ﬂ ammable materials contact hot surfaces.

Never use your appliance for

warming or heating the room.

• Do Not Use Water or Flour on Grease Fires.

Smother the ﬁ re with a pan lid, or use baking

soda, a dry chemical or foam-type extinguisher.

• When heating fat or grease, watch it closely. Fat

or grease may catch ﬁ re if allowed to become too

hot.

• Use Only Dry Potholders. Moist or damp

potholders on hot surfaces may result in burns

from steam. Do not let the potholders touch hot

heating surface units. Do not use a towel or other

bulky cloth instead of a potholder.

• Do Not Heat Unopened Food Containers.

Buildup of pressure may cause the container to

burst and result in injury.

IMPORTANT—Do not attempt to operate the

appliance during a power failure. If power fails,

always turn oﬀ the appliance. If the appliance is

not turned oﬀ and the power resumes, it will begin

to operate again. Once the power resumes, reset

the clock and oven function.

IMPORTANT INSTRUCTIONS FOR USING

YOUR COOKTOP

• Know which knob controls each surface

heating unit. Place a pan of food on the unit

before turning it on, and then turn the unit oﬀ

before removing the pan.

• Use proper pan size. This appliance is equipped

with one or more surface units of diﬀ erent sizes.

Select utensils having ﬂ at bottoms large enough

to cover the surface unit. The use of undersized

utensils will expose a portion of the surface

heating unit to direct contact and may result in

ignition of clothing. Proper relationship of utensil

to the surface unit will also improve eﬃ ciency.

• Utensil handles should be turned inward and

not extend over adjacent surface units. To

reduce the risk of burns, ignition of ﬂ ammable

materials, and spillage due to unintentional

contact with the utensil.

• Never leave surface units unattended—

Boilovers cause smoking and greasy

accumulations that may ignite, or a pan that has

boiled dry may melt.

• Glazed cooking utensils—Only certain types of

glass, glass/ceramic, ceramic, earthenware, or

other glazed utensils are suitable for rangetop

service without breaking due to the sudden

change in temperature. Check the manufacturer’s

recommendations for cooktop use.

IMPORTANT INSTRUCTIONS FOR USING

YOUR OVEN

• Use Care When Opening an Oven Door or

a Warmer Drawer—Stand to the side of the

appliance when opening the door of a hot oven.

Let hot air or steam escape before you remove or

replace food in the oven.

• Keep Oven Vent Ducts Unobstructed. The oven is

vented at the at the center trim above the oven.

Touching the surfaces in this area when the oven

is operating may cause severe burns. Also, do

not place plastic or heat-sensitive items near the

oven vent. These items could melt or ignite.

NEVER cover any slots, holes or

passages in the oven bottom or cover an entire

rack with materials such as aluminum foil. Doing

so blocks air ﬂ ow through the oven and may cause

carbon monoxide poisoning. Aluminum foil linings

may trap heat, causing a ﬁ re hazard.

• Placement of Oven Racks. Always place oven

racks in desired location while oven is cool.

Remove all utensils from the rack before removing

rack. If rack must be moved while oven is hot, use

extreme caution. Use pot holders and grasp the

rack with both hands to reposition. Do not let pot

holders contact the hot oven element or interior of

the oven.

• Do not use the broiler pan without its insert. The

broiler pan and grid allow dripping fat to drain

and be kept away from the high heat of the

broiler.

• Do not cover the broiler grid or oven bottom with

aluminum foil. Exposed fat and grease could

ignite.

5

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

• Do not touch a hot oven light bulb with a damp

cloth. Doing so could cause the bulb to break.

Disconnect the appliance or shut oﬀ the power to

the appliance before removing and replacing the

bulb.

• Protective liners—DO NOT USE ALUMINUM

FOIL TO LINE THE OVEN BOTTOM. Only use

aluminum foil as recommended in this manual.

Improper installation of these liners may result in

risk of electric shock, or ﬁ re.

SELF-CLEANING OVEN MODELS

• Clean in the self-cleaning cycle only the parts

of the appliance listed in this Use & Care

Guide. Before using the self-cleaning cycle of

the appliance, remove the broiler pan and any

utensils stored in the appliance.

• Do not clean the oven door gasket. The door

gasket is essential for a good seal. Care should

be taken not to rub, damage or move the gasket.

• Do not use oven cleaners. No commercial oven

cleaner or oven liner protective coating of any

kind should be used in or around any part of the

appliance

The health of some birds is

extremely sensitive to the fumes given oﬀ during

the self-clean cycle of any oven. Move birds to

another well ventilated room.

IMPORTANT INSTRUCTIONS FOR

CLEANING YOUR OVEN

• Clean the appliance regularly to keep all parts

free of grease that could catch ﬁ re. Exhaust fan

ventilation hoods and grease ﬁ lters should be

kept clean. Do not allow grease to accumulate.

Greasy deposits in the fan could catch ﬁ re.

Refer to the hood manufacturer’s instructions for

cleaning.

• Clean Ventilating Hoods Frequently—Grease

should not be allowed to accumulate on the hood

or ﬁ lter. Follow manufacturer’s instructions for

cleaning.

FOR CERAMIC GLASS COOKTOPS

• Do not clean or operate a broken cooktop—If

cooktop should break, cleaning solutions and

spillovers may penetrate the broken cooktop and

create a risk of electric shock. Contact a qualiﬁ ed

technician immediately.

• Clean cooktop glass with caution—If a wet

sponge or cloth is used to wipe spills on a hot

cooking area, be careful to avoid a steam burn.

Some cleaners can produce harmful fumes if

applied to a hot surface.

• Avoid scratching the cooktop glass with sharp

objects.

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to

publish a list of substances known to the state to cause cancer, birth defects or other productive harm,

and requires businesses to warn customers of potential exposure to such substances.

6

Features at a Glance

NOTE: The features of your range may vary according to

model type & color.

2

1

3 4 5

6

10

13

11

14

15

16

17

19

18

21

22

24

25

23

20

12

7 8

9

Your Range includes:

1. Electronic oven control with kitchen timer.

2. Left bridge element size selector.

3. Left bridge element control and electronic display.

4. Left rear element control and electronic display.

5. Warmer drawer control and electronic display.

6. Center rear element control and electronic display.

7. Right rear element control and electronic display.

8. Right front element control and electronic display.

9. Right front element size selector.

10. Self-clean door latch.

11. Oven vent.

12. Broil element.

13. Self-cleaning convection oven interior.

14. Dual convection bake cooking system.

15. Adjustable interior porcelain oven rack(s).

16. Large 1-piece oven door handle.

17. Full width oven door with window.

18. Warmer drawer.

19. 7” single radiant element.

20. 7” single radiant element.

21. 6” single radiant element.

22. Bridge radiant element.

23. 6” / 9”/ 12” triple radiant element.

24. 7” single radiant element.

25. Ceramic glass cooktop.

7

Before Setting Oven Controls

Oven Vent

1 Oven Rack

Multiple Oven Racks

Oven Vent Location

The oven is vented through its upper front frame. When

the oven is on, warm air is released through the vent. This

venting is necessary for proper air circulation in the oven

and good baking results. Do not block oven vent.

Some

models are equipped

with a blower which

runs in baking and

self-cleaning mode

to keep all internal

components at a cool

temperature. The

blower may keep run-

ning even if the oven

has been turned oﬀ ,

until the components

have cooled down.

Arranging Oven Racks

Always use pot holders or oven mitts when

adjusting the oven racks. Wait until the oven has completely

cooled if possible. Oven racks may be HOT and cause burns.

To remove an oven rack, pull the rack forward until it stops.

Lift up front of rack and slide out.

To replace an oven rack, ﬁ t the rack onto the guides on the

oven walls. Tilt the front of the rack upward and slide the

rack back into place.

Air Circulation in the Oven

If using 1 rack, place in center of oven. If using multiple

racks, stagger cookware as shown.

For best air circulation and baking results allow 2-4” (5-10

cm) around the cookware for proper air circulation and be

sure pans and cookware do not touch each other, the oven

door, sides or back of the oven cavity. The hot air must

circulate around the pans and cookware in the oven for even

heat to reach around the food.

Types of Oven Racks

Always use pot holders or oven mitts when

adjusting the oven racks. Wait until the oven has completely

cooled if possible. Oven racks may HOT and cause burns.

Your appliance may be equipped with one or more of the

oven rack types shown; Flat Handle Oven Rack and Flat

Half Oven Rack.

The Flat Oven Handle Rack has an handle to facilitate the

sliding of the rack when large amount of foods weight on it.

Flat Handle Oven Rack

Flat Half Oven Rack

Closed position

The Flat Oven Half Rack has a removable insert that can

provide extra space for larger food items. The right half rack

portion may still be used for other food items like a casserole

dish. To remove the insert, squeeze on the left front insert side

of the rack and tilt out clockwise. To reinstall, insert rear hooks

at back of insert and lay insert down. Make sure both insert

front hooks snap into rack.

Do not use cookware that extends beyond the edge of the Flat

Half Rack. For best results, allow 2 inches between the pan

placed on the rack and oven side or rear walls.

To Remove the Insert

Squeeze on the left front

insert side of the rack and

tilt out clockwise.

To Reinstall

Insert rear hooks at back of insert and

lay insert down. Make sure both insert

front hooks snap into rack.

8

Selecting Surface Cooking Cookware

Figure 2

Figure 1

Cookware should have ﬂ at bottoms that make good contact

with the entire surface heating element. Check for ﬂ atness

by rotating a ruler across the bottom of the cookware (See

Figure 1). Be sure to follow the recommendations for using

cookware as shown in Figure 2.

Note: The size and type of cookware used will inﬂ uence the

setting needed for best cooking results.

Cookware Material types

The cookware material determines how evenly and quickly

heat is transferred from the surface element to the pan

bottom. The most popular materials available are:

ALUMINUM - Excellent heat conductor. Some types of

food will cause it to darken (Anodized aluminum cookware

resists staining & pitting). If aluminum pans slide across the

ceramic glass cooktop, they may leave metal marks which

will resemble scratches. Remove these marks immediately.

COPPER - Excellent heat conductor but discolors easily. May

leave metal marks on ceramic glass (see Aluminum above).

STAINLESS STEEL - Slow heat conductor with uneven

cooking results. Is durable, easy to clean and resists staining.

CAST IRON - A poor heat conductor however will retain

heat very well. Cooks evenly once cooking temperature is

reached. Not recommended for use on ceramic cooktops.

PORCELAIN-ENAMEL on METAL - Heating characteristics

will vary depending on base material. Porcelain-enamel

coating must be smooth to avoid scratching ceramic

cooktops.

GLASS - Slow heat conductor. Not recommended for

ceramic cooktop surfaces because it may scratch the glass.

Surface Cookware Recommendations

Correct Incorrect

Flat bottom and straight •

sides.

Tight ﬁ tting lids.•

Weight of handle does •

not tilt pan. Pan is well

balanced.

Pan sizes match the amount •

of food to be prepared

and the size of the surface

element.

Made of a material that •

conducts heat well.

Easy to clean.•

Always match pot diameter •

to element surface

diameter.

Curved and warped pan •

bottoms.

Pan overhangs element by •

more than one-half inch.

Pan is smaller than •

element.

Heavy handle tilts pan.•

Important note:

Do not place empty aluminum, glass or porcelain-enamel

coated cookware on the ceramic cooktop! The melting point

of cookware made with these materials may be reached

quickly especially if left empty & they may bond to the

ceramic cooktop. If the cookware melts it will damage the

cooktop! Be sure to follow all the cookware manufacturer’s

suggestions when using any type of cookware on the

ceramic cooktop.

9

Before Setting Surface Controls

Figure 1

About the Ceramic Glass Cooktop

The ceramic cooktop has radiant surface elements

located below the surface of the glass. The design of the

ceramic cooktop outlines the area of the surface element

underneath.

Note: (White glass cooktops only) Due to the high intensity

of heat generated by the surface elements, the glass surface

will turn green when the element is ﬁ rst turned oﬀ . This

phenomenon is normal and the glass will come back to its

ori

g

inal white color after it has com

p

letel

y

cooled down.

Heat is transferred up through the surface of the cooktop

to the cookware. Only ﬂ at-bottom cookware should be

used. The type and size of cookware, the number of surface

elements in use and their settings, are all factors that will

aﬀ ect the amount of heat that will spread to areas beyond

the surface elements.

The areas surrounding the elements may

become hot enough to cause burns.

About the Radiant Surface Elements

The element temperature rises gradually and evenly. As the

temperature rises, the element will glow red. To maintain

the selected setting, the element will cycle on and oﬀ . The

heating element retains enough heat to provide a uniform

and consistent heat during the oﬀ cycle.

For eﬃ cient cooking, turn oﬀ the element several minutes

before cooking is complete. This will allow residual heat to

complete the cooking process.

Important notes:

• Radiant elements have a limiter that allows the element

to cycle ON and OFF, even at the HI setting. This helps

to prevent damage to the ceramic cooktop. Cycling at

the HI setting is normal and will occur more often if the

cookware is too small for the radiant element or if the

cookware bottom is not ﬂ at.

• Pressing a cooktop keypad only activates or deactivates

the element but will not start the heating process. Activat-

ing and powering any surface cooking element requires

pressing two keys - the ON/OFF keypad ﬁ rst and then a

power level section must be added before the element

will begin heating.

• Be sure to read the detailed instructions for ceramic glass

cooktop cleaning in the Care & Cleaning and Before You

Call checklist sections of this Use & Care Guide.

Home Canning

Be sure to read and observe all the following points when

home canning with your appliance. Check with the USDA

(United States Department of Agriculture) website and be

sure to read all the information they have available as well

as follow their recommendations for home canning proce-

dures.

• Use only quality ﬂ at bottom canners when home canning.

Use a straight edge to check canner bottom.

• Use only a completely ﬂ at bottom canner with no ridges

that radiate from the bottom center when home canning

using a ceramic cooktop.

• Make sure the diameter of the canner does not exceed 1

inch beyond the surface element markings or burner. It is

recommended to use smaller diameter canners on electric

coil and ceramic glass cooktops.

• Start with hot tap water to bring water to boil more

quickly.

• Use the highest heat seating when ﬁ rst bringing water to

a boil. Once boiling is achieved, reduce heat level to low-

est possible setting to maintain that boil.

• NEVER place or straddle a cooking utensil over two dif-

ferent surface cooking areas at the same time. This will

cause uneven heating results and may cause the ceramic

cooktop to fracture.

10

Before Setting Surface Controls

Fig. 1

Fig. 5

Fig. 8

Fig. 9

Fig. 10

Fig. 6 Fig. 7

Fig. 2 Fig. 3 Fig. 4

Cooktop Display Windows

The cooktop controls provide a digital display for each of

the radiant surface elements located on the cooktop. Power

levels and messages are easily monitored and adjusted

using the corresponding control keypads in combination with

the window displays.

The Available Power Level Settings

The cooktop control will display heat levels ranging from Hi

(Figure 1) to Lo (Figure 6) and OFF (Figure 7). The settings

between 9.5 (Figure 2) and 3.0 (Figure 3) decrease or

increase in increments of .5 (1/2). The settings between

2.8 (Figure 4) and 1.2 (Figure 5) are Simmer settings which

decrease or increase in increments of .2 (1/5) to Lo (Figure

6; lowest Simmer setting) for more precise settings at lower

heat levels.

Hot Element Indicator Message (HE)

After using any of the radiant element positions the cooktop

will become very hot. Even after setting the controls to OFF,

the cooktop will remain hot for some time. The cooktop

control monitors the temperature of the cooktop and

displays the message “HE” (hot element) warning when the

cooktop is still too hot to touch (Figure 8). If the HE message

appears in the window, the control can still be turned on

again for use.

Power Failure (PF) Message

The PF message (Figure 9) will be displayed whenever there

has been a power interruption to the appliance. The PF

message will disappear by itself after a few seconds.

Sabbath Feature (Sb) Message

The cooktop display windows will show the Sb message

whenever the Sabbath feature is active (Figure 10). When

activated, the Sabbath feature works for both the oven

and cooktop together. Once the Sabbath feature is active,

changes to the heat levels for the cooktop heating elements

will not show in the displays. The cooktop will react slower

to heat level changes. See Sabbath feature section for

complete instructions.

Fig. 12

Fig. 11

Cooktop Lockout (--)

Use the Cooktop Lockout to lock all surface elements from

being accidentally turned ON (including Warmer Zone). This

feature will only lockout the cooktop features.

To turn the Cooktop Lockout feature ON:

1. Be sure all surface element controls are OFF.

2. Press and hold Cooktop Lockout keypad until acceptance

tone sounds (about 3 seconds).

When the cooktop is locked, the cooktop locked indicator

icon will appear in the oven control display window (Fig. 11).

The (--) message will appear in the cooktop display windows

whenever the Cooktop Lockout feature is active (See Fig. 12).

If a triple beep sounds (entry error tone) instead, check

and be sure all surface elements are turned OFF before

activating the Cooktop Lockout feature.

To turn the Cooktop Lockout feature OFF:

Press and hold Cooktop Lockout keypad until acceptance

tone sounds (about 3 seconds). The cooktop locked indicator

light will turn OFF and the cooktop may be used for normal

cooking operations.

Important notes:

• If Cooktop Lockout is active and a power failure occurs,

when power is restored the cooktop will remember the

setting and remain locked.

• Starting a Flex Clean cycle will automatically turn ON the

Cooktop Lockout feature. The cooktop will remain locked

until the Flex Clean cycle is ﬁ nished and the oven door

has unlocked.

11

Hot Element Indicator Message

After using any of the radiant element positions the cooktop

will become very hot. Even after setting the controls to OFF,

the cooktop will remain hot for some time. The cooktop

control monitors the temperature of the cooktop and

displays the message “HE” (hot element) warning when the

cooktop is still too hot to touch. If the HE message appears

in the window, the control can still be turned on again for

use.

Setting Surface Controls

To Operate the Single Radiant Surface Elements:

1. Place correctly sized cookware on the radiant surface

element.

2. Touch and hold the

pad for the desired element

position until a beep is heard. The display will show “--”.

Note: If no further pads are touched within 10 seconds

the request to power the element ON will clear.

3. Touch Hi pad once to turn ON the power level to HI.

Touch Lo pad once for Lo power level.

4. Each touch of the Hi or Lo pad will decrease or increase

the power level from 9.0 through 3.0 by .5 increments.

Simmer power levels between 3.0 and 1.2 will decrease

or increase by .2 increments. Lo is the lowest power level

available.

Note: The power level may be adjusted at any time

while the element is ON.

5. When cooking has been completed touch the

pad

once to turn the element OFF.

Radiant surface elements may appear to

have cooled after they have been turned oﬀ . The glass

surface may still be hot and burns may occur if the glass

surface is touched before it has cooled suﬃ ciently.

Do not place aluminum foil, plastic items

such as salt and pepper shakers, spoon holders or plastic

wrappings on top of the range when it is in use. These

items could melt or ignite. Potholders, towels or wooden

spoons could catch ﬁ re if placed too close to the surface

elements.

Single Radiant Element

The cooktop provides single

radiant element located as

illustrated. Use the following

instructions when operating these

elements.

The suggested power level settings shown in Fig. 1 are based

on cooking with medium sized aluminum pans with lids. Be

sure to make any further setting adjustments for best surface

cooking results.

Suggested radiant element power level settings table

Setting Type of cooking

High (8.0 - Hi) Start most foods, bring water to a

boil, pan broiling.

Medium high

(5.0-8.0)

Continue a rapid boil, fry, deep fat

fry.

Medium (3.0 - 5.0) Maintain a slow boil, thicken sauces

and gravies or steam vegetables.

Medium low

(2.0 - 3.0)

Keep foods cooking, poach, stew

(2.8 or lower is a simmer setting).

Low (Lo - 2.0) Keep warm, melt, simmer (2.8 or

lower is a simmer setting).

Fig. 1

Important notes:

• Start most cooking operations on a higher setting and

then turn to a lower setting to ﬁ nish cooking.

• For eﬃ cient cooking, turn the surface element OFF

several minutes before cooking is complete. This will allow

residual heat to complete the cooking process.

• A glowing red surface heating area extending beyond the

bottom edge of the cookware indicates the cookware is

too small for the surface heating area.

• Radiant elements have a limiter that allows the radiant

heating element to cycle ON and OFF, even at the

HI setting. This helps prevent damage to the ceramic

cooktop. Cycling at the HI setting is normal and will occur

more often if the cookware is too small for the radiant

element or if the cookware bottom is not ﬂ at.

12

Setting Surface Controls

Triple Radiant Element

The cooktop provides a triple

radiant element located as

illustrated. Use the following

instructions when operating these

elements.

Use the SIZE keypad (Fig. 1) to select which portions of the

triple element are needed for heating. The triple element

size may be changed anytime the element is ON.

To Operate the Triple Radiant Element:

1. Place correctly sized cookware on the triple radiant

element.

2. To activate press and hold the

keypad for the triple

element until acceptance tone sounds.

3. Press SIZE keypad and toggle to select the single (Fig. 2),

double (Fig. 3) or triple (Fig. 4) element size setting.

4. To set power level press Hi or Lo keypad and if needed

toggle the Hi or Lo keypads to adjust to the desired

power level setting. Each touch of the Hi or Lo key pad

will decrease or increase the power level by 1/2 from 9.0

through 3.0. Simmer power levels between 3.0 and 1.2 will

decrease or increase by .2 increments. Hi (Fig. 5) is the

highest power level. Lo (Fig. 6) is the lowest power level

available.

5. Once cooking is ﬁ nished, press

keypad to turn the

triple element OFF (Fig. 7).

Hot Element Indicator Message

After using any of the radiant element positions the cooktop

will become very hot. Even after setting the controls to OFF,

the cooktop will remain hot for some time. The cooktop

control monitors the temperature of the cooktop and

displays the message “HE” (hot element) warning when the

cooktop is still too hot to touch. If the HE message appears

in the window, the control can still be turned on again for

use.

Radiant surface elements may appear to

have cooled after they have been turned oﬀ . The glass

surface may still be hot and burns may occur if the glass

surface is touched before it has cooled suﬃ ciently.

Do not place aluminum foil, plastic items

such as salt and pepper shakers, spoon holders or plastic

wrappings on top of the range when it is in use. These

items could melt or ignite. Potholders, towels or wooden

spoons could catch ﬁ re if placed too close to the surface

elements.

Fig. 1

Fig. 2

Fig. 5

Fig. 3

Fig. 6

Fig. 4

Fig. 7

Important notes:

• If no element size is chosen when the triple element is

turned ON, only the inner coil will heat by default.

• Start most cooking operations on a higher setting and

then turn to a lower setting to ﬁ nish cooking.

• For eﬃ cient cooking, turn the surface element OFF

several minutes before cooking is complete. This will allow

residual heat to complete the cooking process.

• A glowing red surface heating area extending beyond the

bottom edge of the cookware indicates the cookware is

too small for the surface heating area.

• Radiant elements have a limiter that allows the radiant

heating element to cycle ON and OFF, even at the

HI setting. This helps prevent damage to the ceramic

cooktop. Cycling at the HI setting is normal and will occur

more often if the cookware is too small for the radiant

element or if the cookware bottom is not ﬂ at.

13

Setting Surface Controls

Bridge Radiant Element

The cooktop provides a bridge

radiant element located as

illustrated. The bridge can be used

when cooking with rectangular

(like a griddle) or oval shaped

cookware.

The element will maintain an even temperature setting

across all portions of the Bridge. If needed for normal

cookware, the Bridge element can work like a single element

without the Bridge (Fig. 2).

Use the SIZE keypad (Fig. 1) to select which portions of the

bridge element are needed for heating. The bridge element

size may be changed anytime the element is ON.

To Operate the Bridge Radiant Element:

1. Place correctly sized cookware on the bridge radiant

element.

2. To activate press and hold the

keypad for the bridge

element until acceptance tone sounds.

3. Press SIZE keypad and toggle to select the front portion

(Fig. 2), both front and middle portions (Fig. 3) or all three

portions (Fig. 4).

4. To set power level press Hi or Lo keypad and if needed

toggle the Hi or Lo keypads to adjust to the desired

power level setting. Each touch of the Hi or Lo key pad

will decrease or increase the power level by 1/2 from 9.0

through 3.0. Simmer power levels between 3.0 and 1.2 will

decrease or increase by .2 increments. Hi (Fig. 5) is the

highest power level. Lo (Fig. 6) is the lowest power level

available.

5. Once cooking is ﬁ nished, press

keypad to turn the

bridge element OFF (Fig. 7).

Hot Element Indicator Message

After using any of the radiant element positions the cooktop

will become very hot. Even after setting the controls to OFF,

the cooktop will remain hot for some time. The cooktop

control monitors the temperature of the cooktop and

displays the message “HE” (hot element) warning when the

cooktop is still too hot to touch. If the HE message appears

in the window, the control can still be turned on again for

use.

Radiant surface elements may appear to

have cooled after they have been turned oﬀ . The glass

surface may still be hot and burns may occur if the glass

surface is touched before it has cooled suﬃ ciently.

Do not place aluminum foil, plastic items

such as salt and pepper shakers, spoon holders or plastic

wrappings on top of the range when it is in use. These

items could melt or ignite. Potholders, towels or wooden

spoons could catch ﬁ re if placed too close to the surface

elements.

Fig. 1

Fig. 2

Fig. 5

Fig. 3

Fig. 6

Fig. 4

Fig. 7

Important notes:

• If no element size is chosen when the bridge element is

turned ON, only the front portion will heat by default.

• Start most cooking operations on a higher setting and

then turn to a lower setting to ﬁ nish cooking.

• For eﬃ cient cooking, turn the surface element OFF

several minutes before cooking is complete. This will allow

residual heat to complete the cooking process.

• A glowing red surface heating area extending beyond the

bottom edge of the cookware indicates the cookware is

too small for the surface heating area.

• Radiant elements have a limiter that allows the radiant

heating element to cycle ON and OFF, even at the

HI setting. This helps prevent damage to the ceramic

cooktop. Cycling at the HI setting is normal and will occur

more often if the cookware is too small for the radiant

element or if the cookware bottom is not ﬂ at.

14

Oven Control Functions

Minimum & maximum

control settings

All of the features listed below have

minimum and maximum time or

temperature settings that may be

entered into the control. An ENTRY

acceptance beep will sound each

time a control pad is touched (the

Oven Lockout pad is delayed 3

seconds).

An ENTRY ERROR tone (3 short

beeps) will sound if the entry of the

temperature or time is below the

minimum or above the maximum

settings for the feature.

Feature Min. Temp. or time Max. temp. or time

PreHeat 170°F/77°C 550°F/288°C

Bake 170°F/77°C 550°F/288°C

Broil 400°F/205°C 550°F/288°C

Timer 0:01 Min. 11:59 Hr./Min.

Flex Clean 2 hours 4 hours

Conv Bake 170°F/77°C 550°F/288°C

Conv Convert 170°F/77°C 550°F/288°C

Conv Roast 170°F/77°C 550°F/288°C

Slow Cook Lo (225°F/180°C) Hi (225°F/180°C)

Cook Time 0:01 Min. 11:59 Hr./Min.

Delay Time 12 Hr. 1:00 Hr./Min. 12:59 Hr./Min.

Delay Time 24 Hr. 0:00 Hr./Min. 23:59 Hr./Min.

Oven Control Keypads

1. Timer - Used to set or cancel Timer.

2. Add 1 Minute - Used to add additional minutes to Timer.

3. Cook Time- Used to enter the length of the cook time

desired.

4. Delay Start - Used with Bake, Conv Bake, Conv Convert

and Flex Clean functions to program a delay start time

or delay start self-cleaning cycle.

5. Slow Cook - Used to select the Slow Cook function.

6. Warm - Used to set the Warm & Hold function.

7. Preheat - Used to pre-condition the oven.

8. Cakes & Breads - Used to select the cakes and breads.

9. Conv Convert - Used to select the Convection Convert

function.

10. Clean - Used to set a 2 to 4 hours Self-Clean cycle.

11. Conv Bake - Used to select the Convection Bake feature.

12. Bake - Used to enter the normal bake feature.

13. START - Used to start oven functions.

14. Broil - Used to select Broil feature.

15. Conv Roast - Used to select the Convection Roast

function.

16. Cooktop Lockout - Used to lock the cooktop functions.

17. Oven Light - Used to turn oven light ON and OFF.

18. STOP - Used to cancel any oven function previously

entered except Clock and Timer.

19. Clock Set - Used to set the time of day.

20. Oven Lockout - Used to lock oven functions and door.

0 thru 9 number - Used to enter temperature and times.

For satisfactory use of your oven, become familiar with the various features and functions of the oven.

1

4

7

10

2

5

8

11

3

6

9

13 14

18

15

1916 2017

12

15

Getting Started

Setting Clock at Power Up

You will be prompted to enter the time of day in the event

of a power failure or when you ﬁ rst provide electric power

to your appliance.

• When your appliance is ﬁ rst powered up, 12:00 will ﬂ ash

in the display.

• Enter the time of day using the numeric key pads and

press START to set.

If an invalid time of day is entered, the control will triple

beep. Re-enter a valid time of day and press START. If

STOP is pressed your clock will start with the time set for

12:00.

Select the CLOCK

key to modify the time of day during

other situations such as day light savings.

To Set Add 1 Minute Feature

The ADD 1 MINUTE pad is used to set the Add 1 Minute

feature. When the pad is pressed, 1 minute is added to the

Timer feature if this feature is already active. If the Timer

feature is not active and the pad is pressed, the Timer

feature will become active and will begin counting down

from 1 minute. For further information on how to set the

Timer feature see Timer instructions above.

Setting Timer

See example below to set the timer for 5 minutes:

NOTE: The timer(s) will not aﬀ ect the cooking process.

The timer provided with the oven control serve as extra

reminders in the kitchen. When the timer reaches less than 1

minute the display will start to count down in seconds. When

the time runs out the active timer will beep, and “End” will be

displayed.

The following time settings apply to the timers:

• Min. time: 1 minute

• Max. time: 11 hours 59 minutes

To cancel or end the timer, press the TIMER key again.

1. Press TIMER

2. Enter 5 minutes

3. Press START

Setting Oven Lockout

The Oven Lockout feature automatically locks the oven door

and prevents the oven from being turned on. It does not

disable the clock, Timer or the interior oven lights.

See example below to lock the oven.

DOOR LOCKED will ﬂ ash in the display until the door has

ﬁ nished locking. Once the door has been locked the door

lock indicator will turn on. DOOR LOCKED will then stay

displayed.

Do not attempt to open the oven door while the door lock

indicator is ﬂ ashing.

To lock, press and hold OVEN

for 3 seconds.

To unlock, press and hold OVEN for 3 seconds.

The preheat temperature display is available with the

following cooking modes:

• Bake

• Conv Bake

Preheat Temperature Display

Once a cooking feature has been started, the control will

display the actual oven temperature while preheating. Once

the oven reaches the oven set temperature, only the oven set

temperature will be displayed.

16

Setting Oven Controls

Pan position for two rack

baking.

Pan position for one rack

baking.

See example below to set a preheat to start immediately at

the default temperature.

Setting preheat

For best baking performance use the Preheat feature. The

Preheat feature will bring the oven up to the set cooking

temperature. A reminder tone will sound indicating when

the set temperature is reached and to place the food in the

oven. Preheating is not necessary when roasting or cooking

casseroles.

The following temperature settings apply to the preheat

feature:

• Auto-suggest (default) setting: 350°F/177°C

• Min. bake setting: 170°F / 77°C

• Max. bake setting: 550°F / 288°C

Preheat

1. Press PREHEAT

If needed, use numeric keypads to enter a diﬀ erent oven

temperature.

2. Press START

When the oven is ﬁ nished preheating, the controls will beep

to remind you to place food in the oven. The preheat feature

will perform like the Bake feature and continue to maintain

the oven set temperature until cancelled.

"PRE" and the actual oven temperature shown in the display

will alternate as the oven heats and reaches set temperature.

NOTE

To cancel the function, you may press • STOP at any time

when setting the control or during the cooking process.

To change the set temperature while the oven is already •

heating, follow the same procedure described above.

During the preheating, the convection fan will be activated •

to allow the oven to reach its target temperature faster.

The Bake, Broil and Convection elements will also cycle for

a better heat distribution.

See example below to set a bake to start immediately at

the default temperature.

Once START is pressed the oven will begin heating. The

oven display shows the temperature rising.

After the oven reaches set temperature a beep will indicate

the oven is ready. The oven will continue to maintain this

temperature until the cooking feature is canceled.

NOTE

To cancel the function, you may press STOP at any time

when setting the control or during the cooking process.

To change the set temperature while the oven is already

heating, follow the same procedure described above.

During the preheating, the convection fan will be activated

to allow the oven to reach its target temperature faster.

The Bake, Broil and Convection elements will also cycle for

a better heat distribution.

Setting bake

Use the bake feature to cook most food items that require

normal cooking temperatures.

The following temperature settings apply to the bake

feature:

• Auto-suggest (default) setting: 350°F/177°C

• Min. bake setting: 170°F / 77°C

• Max. bake setting: 550°F / 288°C

• As much as possible, use only one rack on position 2 or

3 and center the pans. If using two racks, place the oven

racks in position 2 and 4.

• When placing multiple food items in the oven allow 2-4”

(5-10cm) of space between the food items for proper air

circulation.

• Dark or dull pans absorb more heat than shiny bakeware

resulting in dark or overbrowning of foods. It may be

necessary to reduce the oven temperature or cook time

to prevent overbrowning of some foods. Dark pans are

recommended for pies. Shiny pans are recommended for

cakes, cookies and muﬃ ns.

For best results

Bake

1. Press BAKE

If needed, use numeric keypads to enter a diﬀ erent oven

temperature.

2. Press START

17

Setting Oven Controls

FOOD POISONING HAZARD. Do not let food sit for more than one hour before or after cooking. Doing so can result in

food poisoning or sickness. Foods that can easily spoil such as milk, eggs, ﬁ sh, meat or poultry, should be chilled in the

refrigerator ﬁ rst. Even when chilled, they should not stand in the oven for more than 1 hour before cooking begins, and

should be removed promptly when ﬁ nished cooking.

Cook Time

Adding a cook duration when baking is beneﬁ cial when a

recipe requires a speciﬁ c temperature and period of time to

cook. Following the recipe cook time helps insure the best

possible results.

Cook time may be set with the following features:

• Preheat

• Bake

• Conv Bake

• Conv Roast

• Slow Cook

See example below to set the oven for bake, starting

immediately with preheating to the auto-suggest (default)

setting of 350°F (177°C) and then to automatically turn oﬀ

after 30 minutes:

Once START is pressed the oven will cook and after 30

minutes automatically shut-oﬀ .

1. Press BAKE

2. Press START

3. Press COOK TIME

4. Enter 30 minutes

5. Press START

NOTE

To cancel the function, you may press• STOP at any time

when setting the control or during the cooking process.

The maximum Cook Time setting is 11 hours and 59 •

minutes.

After the Cook Time feature has been activated, the •

display will go back to showing the hour of day. Press the

COOK TIME keypad to display any remaining cook time.

• Dark or dull pans absorb more heat than shiny bakeware

resulting in dark or overbrowning of foods. It may be

necessary to reduce the oven temperature or cook time

to prevent overbrowning of some foods. Dark pans are

recommended for pies. Shiny pans are recommended for

cakes cookies or muffins

When the Cook Time ﬁ nishes:

1. "End" and the time of day will show in display. The oven

will shut oﬀ automatically.

2. The control will beep 3 times. The control will continue to

beep 3 times every 30 seconds until STOP is pressed.

Delay Start (with cook time)

NOTE

When setting the • DELAY START option be sure the correct

time of day is set.

You may press • STOP any time when setting the control or

during the cooking process.

You may also choose to use • DELAY START with no COOK

TIME.

Delay Start may be set using a 24 hour clock. See Setting 12 •

or 24 hour display modes for more information.

Adding a cook duration along with a speciﬁ c start time

gives the same beneﬁ ts as the cook time option in addition

to controlling exactly when the cooking process will begin

and end.

Delay start may be set with the following features:

• Bake

• Conv Bake

• Conv Roast

• Slow Cook

• Flex Clean

See example below to set the oven with preheating for bake

at 375°F (191°C) for 50 minutes and to automatically start

at 5:30:

Once START is pressed, the oven will calculate the start time

at which the oven will begin heating.

The oven will continue to maintain this temperature for the

selected time or until the cooking feature is canceled.

1. Press BAKE

2. Enter 375°F

3. Press START

4. Press COOK TIME

5. Enter 50 minutes

6. Press START

7. Press DELAY START

8. Enter 5:30

9. Press START

18

Pan position for two rack baking.

Pan position for one rack baking.

Convection air ﬂ ow

Setting Oven Controls

Convection Bake uses a fan to circulate the oven heat evenly

and continuously. The improved heat distribution allows for

even cooking with excellent results. Multiple rack cooking

may slightly increase cook times for some foods, but the

overall result is time saved.

Convection Bake

Beneﬁ ts of convection bake:

• Superior multiple oven rack performance.

• Some foods cook up 25 to 30% faster, saving time and

energy.

• No special pans or bakeware required.

See the example below to set conv bake, starting

immediately with the default setting of 350°F (177°C):

After the oven reaches set temperature, a beep will indicate

the oven is ready. The oven will continue to maintain this

temperature until the cooking feature is canceled.

Conv Bake may be set with the following options:

• Conv Convert

• Cook Time and/or Delay Start

The following temperature settings apply to the conv bake

feature:

• Auto-suggest (default) setting: 350°F / 177°C

• Min. bake setting : 170°F / 77°C

• Max. bake setting: 550°F / 288°C

• When baking with a single rack use rack positions 2 or 3.

When using 2 racks use rack positions 2 & 4. When using

3 racks use rack positions 1, 3 & 4.

• Cookies and biscuits should be baked on pans with no

sides or very low side to allow heated air to circulate

around the food.

• Food baked on pans with a dark ﬁ nish will cook faster.

• When placing multiple food items in the oven allow 2-4”

(5-10cm) of space between the food items for proper air

circulation.

For best results

The Conv Bake feature should ONLY be used when your

recipe instructions have been written for use with convection

baking.

If your recipe instructions are for normal baking and

you wish to use convection bake, follow the Convection

Convert option instructions. The convection convert option

will automatically adjust the oven temperature so that

convection baking may provide the best possible results.

1. Press CONV BAKE

If needed, use numeric keypads to enter a diﬀ erent oven

temperature.

2. Press START

NOTE

You may press STOP any time when setting the control or

during the cooking process.

19

Setting Oven Controls

The conv convert option allows you to convert any normal

baking recipe using the convection bake feature. The control

uses the normal recipe settings and adjusts to a lower

temperature for convection baking. Conv convert must be

used with Conv Bake feature.

Convection Convert

NOTE

You may press STOP any time when setting the control or

during the cooking process.

Beneﬁ ts of conv bake using conv convert option:

• Superior multiple oven rack performance.

• Some foods cook up 25 to 30% faster, saving time and

energy.

• No special pans or bakeware required.

• Place food items using the recommended rack positions.

When baking with a single rack use rack positions 2 or 3.

When using 2 racks use rack positions 2 & 4. When using

3 racks use rack positions 1, 3 & 4.

• Cookies and biscuits should be baked on pans with no

sides or very low side to allow heated air to circulate

around the food.

• Food baked on pans with a dark ﬁ nish will cook faster.

• When placing multiple food items in the oven allow 2-4”

(5-10cm) of space between the food items for proper air

circulation.

For best results

After the oven reaches the converted set temperature, a

beep will indicate the oven is ready.

The added conv convert option will automatically lower the

set temperature you set from the bake recipe to an adjusted

conv bake temperature.

When conv convert is used with cook time “CF” (Check

Food) will be displayed when the cook time is 75%

complete. The control will also beep at regular intervals until

baking has ﬁ nished. For the Check Food function to operate,

the cook time must be entered before the Conv Convert pad

is pressed.

See the example below to set conv bake, starting

immediately with the auto-suggest (default) setting of 350°F

(177°C) and adding the conv convert option.

1. Press CONV BAKE

If needed, use numeric keypads to enter a diﬀ erent oven

temperature.

2. Press CONV CONVERT

3. Press START

20

Setting Oven Controls

Convection roast combines a cook cycle with the convection

fan and element to rapidly roast meats and poultry. Heated

air circulates around the meat from all sides, sealing in

j

uices and ﬂ avors. Meats cooked with this feature are crispy

brown on the outside while staying moist on the inside. In

addition, there is no need to reduce the oven temperature

when using convection roast.

Convection roast may be set with the following options:

• Cook time or cook time with delay start

The following temperature settings apply to convection

roast:

• Factory auto-start default: 350°F/177°C

• Minimum: 170°F / 77°C

• Maximum: 550°F / 288°C

Beneﬁ ts of convection roast:

• Superior multiple oven rack performance.

• Some foods cook up 25 to 30% faster, saving time and

energy.

• No special pans or bakeware required.

See example below to set convection roast to start

immediately with the auto-suggest (default) setting:

• Preheating is not necessary for most meats and poultry.

• Be sure to carefully follow your recipe’s temperature and

time recommendations or refer to the convection roast

chart for additional information.

• Do not cover foods when dry roasting - this will prevent

the meat from browning properly.

• Since Conv Roast cooks food faster, reduce the cook time

by 25% from the recommended cook time of your recipe

(check the food at this time). If necessary, increase cook

time until the desired doneness is obtained.

For best results

Once START is pressed the oven will begin heating.

1. Press CONV ROAST

If needed, use numeric keypads to enter a diﬀ erent oven

temperature.

2. Press START

* For beef: med rare 145°F, med 160°F, well done 170°F

** Stuﬀ ed turkey requires additional roasting time. Shield legs and breast with foil to prevent overbrowning and drying of the skin.

Roasting rack instructions

The broil pan, its insert and the roasting rack are available

via the mail order card. When preparing meats for

convection roasting, you may use the broiler pan, insert and

the roasting rack supplied with your appliance. The broiler

pan will catch grease spills and the insert will help prevent

grease splatters. The roasting rack ﬁ ts on top of the insert

allowing the heated air to circulate under the food for even

cooking and helps to increase browning on the underside.

1. Place oven rack on bottom or next to the bottom oven

rack position.

2. Place the insert on the broiler pan.

3. Make sure the roasting rack is securely seated on top of

the insert. Do not use the broiler pan without the insert.

Do not cover the insert with aluminum foil.

4. Position food (fat side up) on the roasting rack. -Fig. 1-

5. Place prepared food on oven rack in the oven.

Roasting rack

Insert

Broil pan

Meat Weight Oven temp Internal temp Minute per lb.

Beef

Standing rib roast 4 to 6 lbs. 350°F * 25-30

Rib eye roast 4 to 6 lbs. 350°F * 25-30

Tenderloin roast 2 to 3 lbs. 400°F * 15-25

Poultry

Turkey, whole** 12 to 16 lbs. 325°F 180°F 8-10

Turkey, whole** 16 to 20 lbs. 325°F 180°F 10-15

Turkey, whole** 20 to 24 lbs. 325°F 180°F 12-16

Chicken 3 to 4 lbs. 350°F - 375°F 180°F 12-16

Pork

Ham roast, fresh 4 to 6 lbs. 325°F 160°F 30-40

Shoulder blade roast 4 to 6 lbs. 325°F 160°F 20-30

Loin 3 to 4 lbs. 325°F 160°F 20-25

Pre-cooked ham 5 to 7 lbs. 325°F 160°F 30-40

Convection Roast

NOTE

You may press STOP any time when setting the control or

during the cooking process.

La page charge ...

Kenmore C970 Series Manuel utilisateur

Kenmore C970 Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents