HEATSTAR, Inc., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 866-447-2194
WARNING:
— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
— An LP cylinder not connected for use shall not be stored in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light appliance.
• Extinguish any open flame.
• Shut off gas to appliance.
— Service must be performed by a qualified service agency.
This is an un-vented gas-fired portable heater. It uses air (oxygen) from the area in which it is used.
Adequate combustion and ventilation must be provided. Refer to pages 4 & 5.
FORCED-AIR SINGLE-FUEL
NOMAD HEATER
If the information in this manual is not followed exactly, a fire or explosion
may result, causing property damage, personal injury or loss of life.
HS115SF
HS190SF
HS250SF
OPERATING INSTRUCTIONS
AND OWNER’S MANUAL
READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe place
for future reference. Do not allow anyone who has not read these instructions to assemble, light, adjust
or operate the heater.
Model #
LANGUAGES INCLUDED
•ENGLISH
•FRENCH
•SPANISH
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
2
Forced-Air Single-Fuel NOMAD Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
CONTENTS
WARNINGS ..........................................................................2
SPECIFICATIONS ..................................................................3
OPERATING PRECAUTIONS ..................................................4
SAFETY PRECAUTIONS ........................................................4
ODOR FADE WARNING .......................................................5
ASSEMBLY AND PREPARATION FOR OPERATION ................6
HOSE AND REGULATOR INFORMATION ..............................6
RATE SELECTION .................................................................7
OPERATION .........................................................................7
USING THE ACCESSORIES ...................................................8
SHUT DOWN AND STORAGE ...............................................9
MAINTENANCE ....................................................................9
PROPANE TANK SIZE SELECTION .......................................10
TROUBLESHOOTING ..........................................................11
WIRING DIAGRAM ............................................................12
PARTS LISTS AND EXPLODED VIEWS .................................14
WARRANTY INFORMATION ...............................................20
This NOMAD Forced-Air Single-Fuel construction
heater was Assembled in the U.S.A. by:
Enerco Group Inc. 4560 West 160th Street
Cleveland, Ohio 44135
For Questions and Inquiries Contact us at:
CALL: 866-447-2194
FAX: 800-321-0552
VISIT: HEATSTARBYENERCO.COM
Office hours are:
Monday - Friday 8:00am - 5:00pm
60706
WARNING:
YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS,
SO PLEASE READ THESE INSTRUCTIONS BEFORE YOU
OPERATE THIS HEATER.
GENERAL HAZARD WARNING:
FAILURE TO COMPLY WITH THE PRECAUTIONS AND
INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN
RESULT IN DEATH, SERIOUS BODILY INJURY AND
PROPERTY LOSS OR DAMAGE FROM HAZARDS OF
FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON
MONOXIDE POISONING, AND/OR ELECTRICAL SHOCK.
ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW
THE INSTRUCTIONS SHOULD USE OR SERVICE THIS
HEATER.
IF YOU NEED ASSISTANCE OR HEATER INFORMATION
SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC.
CONTACT THE MANUFACTURER.
WARNING:
FIRE, BURN, INHALATION, AND EXPLOSION HAZARD.
KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING
MATERIALS, PAPER, OR CARDBOARD, A SAFE DISTANCE
AWAY FROM THE HEATER. AS RECOMMENDED BY THE
INSTRUCTIONS NEVER USE THE HEATER IN SPACES
WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE
COMBUSTIBLES, OR PRODUCTS SUCH AS GASOLINE,
SOLVENTS, PAINT THINNER, DUST PARTICLES OR
UNKNOWN CHEMICALS.
WARNING:THIS PRODUCT CAN EXPOSE
YOU TO CHEMICALS INCLUDING LEAD AND LEAD
COMPOUNDS, WHICH ARE KNOWN TO THE STATE
OF CALIFORNIA TO CAUSE CANCER AND BIRTH
DEFECTS OR OTHER REPRODUCTIVE HARM. FOR MORE
INFORMATION VISIT WWW.P65WARNINGS.CA.GOV
WARNING: Fuels used in liquefied propane
gas appliances, and the products of combustion of such
fuel, can expose you to chemicals including benzene, which
is known to the State of California to cause cancer and
cause birth defects or other reproductive harm, for more
information go to www.P65Warnings.ca.gov
WARNING:
NOT FOR HOME OR RECREATIONAL VEHICLE USE
Operating Instructions and Owner’s Manual
3
Forced-Air Single-Fuel NOMAD Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
MODEL# (Stock#) HS115SF (F109200) HS190SF (F109210) HS250SF (F109220)
INPUT RATE
HIGH [BTU/HR (kW)] 110,485 (32.4) 190,200 (55.7) 248,403 (72.8)
LOW [BTU/HR (kW)] 76,500 (22.4) 127,100 (37.2) 179,536 (52.6)
FUEL REQUIREMENTS
FUEL TYPE LP (Propane) Gas Only LP (Propane) Gas Only LP (Propane) Gas Only
OPERATING GAS PRESSURE
MAX SUPPLY ["W.C. (kPa)]* 14 (3.5) 14 (3.5) 14 (3.5)
MIN SUPPLY ["W.C. (kPa)]* 7.1 (1.8) 7.6 (1.9) 8.4 (2.1)
MANIFOLD PRESSURE ["W.C. (kPa)] 6.5 (1.6) 6.5 (1.6) 6.5 (1.6)
DUCT PRESSURE
MAXIMUM STATIC PRESSURE [”W.C. (kPa)] 0.35 (0.087) 0.65 (0.162) 0.87 (0.216)
FUEL CONSUMPTION
HIGH [LBS/HR (kg/HR)] 5.15 (2.34) 8.86 (4.02) 11.58 (5.25)
LOW [LBS/HR (kg/HR)] 3.74 (1.70) 5.92 (2.69) 8.37 (3.80)
ELECTRICAL SPECIFICATIONS
ELECTRICAL SUPPLY
(Voltage / Frequency / Phase) 115 V / 60 Hz / 1 Ø 115 V / 60 Hz / 1 Ø 115 V / 60 Hz / 1 Ø
CONTINUOUS AMPERAGE 3.6 A 5.5 A 9.1 A
MOTOR HORSEPOWER 1/3 hp 1/2 hp 3/4 hp
MOTOR WATTAGE 220 W 500 W 800 W
MOTOR R.P.M. 1100 1100 1035
WEIGHTS & DIMENSIONS
HEATER WEIGHT 91 LBS (41.3 kg) 159 LBS (72.1 kg) 165 LBS (74.8 kg)
HEATER DIMENSIONS
LxWxH [in. (cm)]
30" x 23.75" x 15"
(76.2 x 60.3 x 38.1)
35.75" x 34.75" x 20.25"
(90.8 x 88.3 x 51.4)
35.75" x 34.75" x 20.25"
(90.8 x 88.3 x 51.4)
CARTON WEIGHT 102 LBS (46.3 kg) 176 LBS (79.8 kg) 182 LBS (82.6 kg)
CARTON DIMENSIONS
LxWxH [in. (cm)]
34.5" x 25.75" x 20"
(87.6 x 65.4 x 50.8)
39" x 36.75" x 24.25"
(99.1 x 93.3 x 62.1)
39" x 36.75" x 24.25"
(99.1 x 93.3 x 62.1)
*GAS PRESSURE REGULATED TO 11” W.C. (2.7 kPa) WHEN USING THE INCLUDED HOSE AND REGULATOR.
SPECIFICATIONS
TOP SIDES BACK OUTLET
HS115SF 12" (30.5 cm) 12" (30.5 cm) 12" (30.5 cm) 72" (183 cm)
HS190SF 12" (30.5 cm) 12" (30.5 cm) 12" (30.5 cm) 72" (183 cm)
HS250SF 12" (30.5 cm) 12" (30.5 cm) 12" (30.5 cm) 72" (183 cm)
CLEARANCE TO COMBUSTIBLES
4
Forced-Air Single-Fuel NOMAD Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
OPERATING PRECAUTIONS
This is a propane, direct-fired, forced-air heater. It's intended
use is primarily temporary heating of buildings under
construction, alteration or repair.
Propane is heavier than air. If the fuel leaks from a
connection or fitting, it sinks to the floor, collecting there
with the surrounding air, forming a potentially explosive
mixture. Obviously, fuel leaks should be avoided, so set up
the fuel supply with utmost care. Read the Odor Fade and
Propane warnings included in this manual for additional
information about detecting gas leaks. Leak check new
connections or re-connections with a soap and water
solution and follow all connection instructions herein. Also,
ask your propane dealer for advice on the heater application
and supply installation and ask him to check it if there are
any questions.
This heater was designed and certified for use as a
construction heater in accordance with ANSI Standard
Z83.7/CSA 2.14. Check with your local fire safety authority
if you have any questions about your applications. Other
standards govern the use of fuel gases and heat producing
products in specific applications. Your local authority can
advise you about these.
Direct-Fired means that all of the combustion products enter
the heated space. Even though this heater operates very
close to 100 percent combustion efficiency, it still produces
small amounts of carbon monoxide. Carbon monoxide
(called CO) is toxic. We can tolerate small amounts but not a
lot. CO can build up in a heated space and failure to provide
adequate ventilation could result in death. The symptoms of
inadequate ventilation are:
• headache
• dizziness
• burning eyes and nose
• nausea
• dry mouth or sore throat
So, be sure to follow advice about ventilation in these
operating instructions.
"Forced-air" means that a blower or fan pushes the air
through the heater. Proper combustion depends upon this
air flow; therefore, the heater must not be revised, modified
or operated with parts removed or missing. Likewise, safety
systems must not be circumvented or modified in order to
operate the heater.
When the heater is to be operated in the presence of other
people the user is responsible for properly acquainting those
present with the safety precautions and instructions, and of
the hazards involved.
SAFETY PRECAUTIONS
1. Check the heater thoroughly for damage. DO NOT
operate a damaged heater.
2. DO NOT modify the heater or operate a heater which has
been modified from its original condition.
3. Use only the fuel type for which the heater has been
certified (propane).
4. Use only VAPOR WITHDRAWAL type propane supply. If
there is any question about vapor withdrawal, ask your
propane dealer.
5. Mount the propane cylinders vertically (shutoff valve
up). Secure them from falling or being knocked over and
protect them from damage.
6. Locate propane containers at least (USA) 7 ft. (2.13m),
(Canada) 10 ft. (3m) from the heater and do not direct
exhaust toward containers.
7. IMPORTANT Use only the hose and regulator assembly
provided with the heater. Inspect hose assembly before
each use of the heater. If there is excessive abrasion or
wear, or hose is cut, replace with hose assembly listed on
parts list in this manual before using heater.
8. For indoor or outdoor use where adequate ventilation has
been provided. Minimum openings of 1/2 sq. ft. (.046
m²) near the floor and 1/2 sq. ft. (.046 m²) near the
ceiling (also see "Operating Precautions").
9. If at any time gas odor is detected, IMMEDIATELY
DISCONTINUE operation until the source of gas has been
located and corrected. Read enclosed Odor fade and
Propane information for additional information about
detecting propane leaks.
10. While this heater is designed to withstand a reasonable
about of harsh weather. It is best to install the heater such
that it is not directly exposed to water spray, rain and/or
dripping water.
11. Maintain minimum clearance from normal combustible
material like paper, canvas, plastic tarpaulins or similar
coverings and secure them to prevent flapping or
movement due to wind action.
12. Due to the high surface and exhaust temperatures, adults
and children must observe clearances to avoid burns or
clothing ignition.
13. Operate only on a stable, level surface.
14. For use with only approved duct lengths and materials.
15. Use only the electrical power specified. The electrical
connection and grounding must comply with National
Electrical Code - ANSI/NFPA 70 (USA) and CSA C22.1
Canadian Electrical Code, Part 1 (Canada).
16. Use only a properly grounded 3-prong receptacle or
extension cord (6 ft (1.83m) in length minimum).
17. Do not move, handle or service while hot or burning.
18. Use only in accordance with local codes or, in the absence
of local codes, with the Standard for the Storage and
Handling of Liquefied Petroleum Gases ANSI/NFPA 58 and
CSA B149.1, Natural Gas and Propane Installation Code.
Operating Instructions and Owner’s Manual
5
Forced-Air Single-Fuel NOMAD Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
FUEL GAS ODOR
LP gas has man-made odorants added specifically for
detection of fuel gas leaks.
If a gas leak occurs you should be able to smell the
fuel gas. Since this fuel is heavier than air you should
smell for the gas odor low to the floor. ANY GAS
ODOR IS YOUR SIGNAL TO GO INTO IMMEDIATE
ACTION!
• Do not take any action that could ignite the fuel gas.
Do not operate any electrical switches. Do not pull
any power supply or extension cords. Do not light
matches or any other source of flame. Do not use your
telephone.
• Get everyone out of the building and away from the
area immediately.
• Close all propane (LP) gas tank or cylinder fuel supply
valves.
• Propane (LP) gas is heavier than air and may settle in
low areas. When you have reason to suspect a propane
leak, keep out of all low areas.
• Use your neighbor’s phone and call your fuel gas
supplier and your fire department. Do not re-enter the
building or area.
• Stay out of the building and away from the area until
declared safe by the firefighters and your fuel gas
supplier.
• FINALLY, let the fuel gas service person and the
firefighters check for escaped gas. Have them air out
the building and area before you return. Properly
trained service people must repair any leaks, check for
further leakages, and then relight the appliance for you.
ODOR FADING - NO ODOR DETECTED
• Some people cannot smell well. Some people cannot
smell the odor of the man-made chemical added to
propane (LP) gas. You must determine if you can smell
the odorant in these fuel gases.
• Learn to recognize the odor of propane (LP) gas. Local
propane (LP) gas dealers will be more than happy
to give you a scratch and sniff pamphlet. Use it to
become familiar with the fuel gas odor.
• Smoking can decrease your ability to smell. Being
around an odor for a period of time can affect your
sensitivity to that particular odor. Odors present in
animal confinement buildings can mask fuel gas odor.
• The odorant in propane (LP) gas is colorless and
the intensity of its odor can fade under some
circumstances.
• If there is an underground leak, the movement of gas
through the soil can filter the odorant.
• Propane (LP) gas odor may differ in intensity at
different levels. Since Propane (LP) gas is heavier than
air, there may be more odor at lower levels.
• Always be sensitive to the slightest gas odor. If
you continue to detect any gas odor, no matter how
small, treat it as a serious leak. Immediately go into
action as discussed previously.
ATTENTION - CRITICAL POINTS TO REMEMBER
• Propane (LP) gas has a distinctive odor. Learn to
recognize these odors. (Reference Fuel Gas Odor and
Odor Fading sections above.
• Even If you are not properly trained in the service and
repair of the heater, ALWAYS be consciously aware of
the odors of propane (LP) gas.
• If you have not been properly trained in repair and
service of propane (LP) gas then do not attempt to
light heater, perform service or repairs, or make any
adjustments to the heater on the propane (LP) gas fuel
system.
• A periodic sniff test around the heater or at the
heater’s joints; i.e. hose, connections, etc., is a good
safety practice under any conditions. If you smell even
a small amount of gas, CONTACT YOUR FUEL GAS
SUPPLIER IMMEDIATELY. DO NOT WAIT!
UNPACKING (Tools needed: Box cutter)
Remove heater and all components from cardboard
container. Thoroughly inspect all packing material for
pieces that are not garbage. Next check the unit for
possible shipping damage. If any is found immediately
notify the factory.
ODOR FADE WARNING
WARNING- ASPHYXIATION HAZARD
Do not use this heater for heating human living quarters.
• Do not use in unventilated areas.
• The flow of combustion and ventilation air must not be obstructed.
• Proper ventilation air must be provided to support the combustion air requirements of the heater being used.
• Refer to the specification section of the heater’s manual, heater data-plate, or contact the Factory to determine
combustion air ventilation requirements of the heater.
• Lack of proper ventilation air will lead to improper combustion.
• Improper combustion can lead to carbon monoxide poisoning leading to serious injury or death. Symptom of carbon
monoxide poisoning can include headaches dizziness and difficulty in breathing.
6
Forced-Air Single-Fuel NOMAD Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
Assembly
INSTALLING THE WHEELS & FOOT (Tools needed: Pliers)
Most units will be completely assembled. However if for
any reason you do need to assemble these components
follow the these instructions. Using the cardboard that
your heater was shipped in turn your heater on to one
of it sides or its top so that the bottom of the heater is
accessible. First, take the axel and insert it into one of the
wheels supplied. Then on the outside of the wheel place
the large washer over the axle. You can then insert one
of the cotter pins into the hole in the end of the axle and
bend over one or both of the tails of the pin so that it
cannot be removed. Then on the inside of that wheel run
one of the spacers over the other end of the axel so that
it is pressed against the back of the wheel. Then slide the
axle into the holes along the bottom edge of the heater.
Then install the other spacer followed by the other wheel
and washer. You can then insert and bend the other
cotter pin. Finally you can press the rubber hub caps over
the end of the axle. It is designed to press over the washer
to hold the cap in place once you are sure you have the
wheels and axle installed on your heater in the order
shown in figure 1.
INSTALLING THE HANDLE
Most units will be completely assembled. However if for
any reason you do need to assemble these components
follow the these instructions. First locate the metal "U"
shaped handle that was packed with your heater. (Does
not apply to model # HS115SF, If this is your model move
to hose and regulator setup). Next locate the two handle
bolts included in your hardware package. Then, while
looking at the outlet side of the heater open the access
panel opposite the control panel side by removing the
screws that hold it in place around its perimeter. Just
FIGURE 1
above the top edge of the door opening you should see
two holes close to the top edge of the heater. Align the threaded
holes in the handle up to the holes in the cover of the heater.
Then thread the two supplied bolts through the case into the
handle from inside of the case. Using a socket wrench tighten
down the bolts. Be sure not to over tighten.
Hose and Regulator setup
Whenever joining a male threaded pipe to female threaded
pipe, apply a pipe dope compound or PTFE tape to male
threads prior to assembly. Leave the first two threads bare.
SETUP FOR GAS CONNECTION
First locate the hose and regulator assembly included with
your heater. Inspect the hose for cracks, breaks and any
signs of damage. If any damage is found, contact the factory
for a replacement. The regulator end is equipped with a
standard POL connection designed to fit most vertical vapor
draw propane tanks. Note: This is a reverse "left hand"
thread. Next attach the P.O.L. to an appropriately sized tank
for your application. This is a flared fitting and this type of
connection does not require any additional sealant or thread
tape. Check all connections with a mixture of soap and
water for leaks. Mix water and a small amount of dish soap
in a spray bottle and apply the solution on all connections,
looking for small bubbles to appear. If you see bubbles that
is an indication of a leak. Tighten your connection until the
bubble are eliminated. For proper tank sizing, refer to the
sizing chart in the trouble shooting section of this manual.
(page 10)
RATE SELECTION
Your Nomad heater is equipped with multi-rate
technology. During setup of your area to be heated you
have the option to use the heater on either the high or
low setting. In order to bring the heat in your space up
to your desired temperature as quickly as possible set the
heater on its high setting (refer to figure 2). Once you
have your space heated to the desired temperature, you
can then turn your setting to the low position to maintain
your desired temperature resulting in dramatic cost savings
from the lower fuel consumption during the entire heating
project.
1
2
3
5
2
3
4
4
# DESCRIPTION QTY
1 WHEELS 2
2 COTTER PINS 2
3 RETAINER WASHERS 2
4 WHEEL SPACERS 2
5 AXLE 1 FIGURE 2
80K
LOW | RÉGLAGE BAS
AJUSTE DE BAJA
110K
HIGH | ÉLEVÉ
ALTO 60788
Operating Instructions and Owner’s Manual
7
Forced-Air Single-Fuel NOMAD Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
OPERATION (NO THERMOSTAT)
Plug in your unit using an appropriately sized properly
grounded three pronged extension cord. Attach the small
length of power cord on the heater to your extension
cord. Once power is supplied to the heater you should
see the green indicator light above the switch light up.
Before you turn on your heater you will want to ensure
that you make your rate selection. Refer to the "Rate
Selection" section for more information. You can now
flip your power switch to the ON position. After a few
seconds your heater will light and you should feel hot
air begin to emit from the outlet of the heater. With this
setup the heater will run continuously until the operator
flips the switch to the off position. If you would like your
heater to cycle on and off based on the temperature
of the space, you will need to use the supplied remote
thermostat.
OPERATION (WITH THERMOSTAT)
To operate your Nomad heater with a thermostat you will
need to place the thermostat in the environment to be
heated and turn the dial to the lowest temperature. Take
the "Piggy-Back" style plug end that was factory installed
on the thermostat and attach it to the small length of
power cord attached to the heater (located near the
power switch). The male plug end of the heater will
go inside the female receptacle on the thermostat plug
end. Next plug in your properly grounded three pronged
extension cord into the other side of the thermostat
plug. You can now switch on your heater and return to
where you have your thermostat located and set the
temperature at which you would like your heater to cycle
on and off at. Once the temperature in the space to be
heated drops below the point at which your thermostat
is set, the green indicator light above the switch will
illuminate and the heat sequence will begin. The unit
will continue to run until the setting of the thermostat
is satisfied. If your heater shuts down for any reason
other than the operator turns it off or the thermostat
is satisfied, refer to the troubleshooting portion of this
manual on page 11.
INCLUDED THERMOSTAT
Cord to heater Extension cored to power
source
Cord to the
Thermostat
THERMOSTAT HOOKUP
PIGGY BACK PLUG
Part # 00618 FIGURE 3
FIGURE 4
8
Forced-Air Single-Fuel NOMAD Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
heated is needed or required. To use this setup you will
need the end diffuser and the 10' specially designed
ducting. To assemble attach one end of the 10' length of
duct to the duct adapter and the other to the end Diffuser.
Then place the end diffuser in the space to be heated.
USING NOMAD HEATER ACCESSORIES
The Nomad line of forced-air heaters is designed to be
used as a stand alone gas fired heating appliance. It is
also designed and certified to be used with a collection
of useful accessories. For information on any additional
accessories that may be available for your model refer
to the list of accessories in this booklet or visit www.
heatstarbyenerco.com.
USING NOMAD HEATERS WITH DUCT & DIFFUSERS
When using this heater to heat a party tent or construction
environment from out side of the space you will need to
employ the help of a few different diffuser attachments.
Direct Diffuser & Duct Adapter
A direct diffuser allows
the user to duct the heat
being produced by the
Nomad heater into a space
needing heat without
having the heater in that
space. To do this you will
need a duct adapter. The
duct adapter attaches to
special connection points
on the heater that match up to the connectors on the
adapter. Align the tabs on the adapter to the holes on
the heater and turn clock wise to lock them in place. Next
you will need the flexible duct transition piece. The duct
transition is a short piece of special silicone lined ducting
that attaches the adapter to the End diffuser. With the
duct adapter attached to the heater, place the transition
duct piece over the outside of the adapter ring and
tighten down the strap. The other end of the Duct is then
attached to the diffuser see Figure 6. The diffuser is an
accessory designed to help direct the air being discharged
from the heater. The air comes out of the diffuser and
spreads out in multiple directions to better fill the space
and heat more evenly. The channel on top of the diffuser
is designed to hold the tent material from falling in front
of the diffuser. The heater can be used without the
diffuser but it is recommended for more effective and
efficient use.
Long Duct & Diffuser
Nomad heaters are also designed to be used with 10'
of flexible duct for when distance from the area to be
FIGURE 6
DIFFUSER
12" X 10' SILICONE LINED
FLEXIBLE HEATING DUCT
F109108
12" X 30" TRANSITION DUCT F109107 12" DUCT ADAPTER F109106
16" DUCT ADAPTER F10911616" X 30" TRANSITION DUCT F109117
16" X 10' SILICONE LINED
FLEXIBLE HEATING DUCT
F109118
12" UNIVERSAL DIFFUSER
F109105
16" UNIVERSAL DIFFUSER
F109115
FITS HS115SF
FITS HS115SF
FITS HS190SF & HS250SF
FITS HS115SF
FITS HS190SF & HS250SF
FITS HS190SF & HS250SF
DUCT ADAPTER
FIGURE 5
FIGURE 7
FIGURE 8
Operating Instructions and Owner’s Manual
9
Forced-Air Single-Fuel NOMAD Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
SHUTDOWN, STORAGE, & MAINTENANCE
When your Nomad heater is no longer needed there are
a few steps you should take to ensure it is ready and in
working condition the next time you need it.
SHUTDOWN
While the heater is running, turn off the gas supply to
the heater and allow the fuel left in the system and in
the hose and regulator to burn off. This should only take
a few seconds. Then at the heater, flip the switch to the
middle or OFF position. You should allow your heater
to completely cool before placing your heater in storage
or before you
perform any
service or
maintenance.
Once the unit
has cooled verify
that the gas has
been shut off.
Then disconnect
the hose and
regulator from
the fuel source.
Next disconnect
the hose from
the inlet fitting
on the heater
and neatly wrap
up your hose
assembly. You
can then place your hose into storage until it is needed
again. On the HS190SF and HS250SF Nomad units you
can use the optional top mounted storage box to store
your heater hose and regulator along with any other
accessories or tools needed for setup and tear down.
Next unplug the unit and wrap up the thermostat and
return it to storage. Your heater can now be stored.
STORAGE & MAINTENANCE
Before and after extended storage or if the heater was
used in dusty conditions you should thoroughly clean
the heater. With the heater unplugged, use soap, water
and a soft cloth to clean off any loose dust or dirt. While
your Nomad heater is certified to be used outdoor and
can withstand wet weather, water should not be used.
This can cause water to be forced into components
where it should not be. To clean off the inside, you will
need a standard flat head screwdriver to open the access
panel. To clean do not use water, use compressed air
to blow dust and debris from the insides. Once the unit
is again clean shut the door and secure the latch with
the screwdriver used to open it. You can now store your
heater until it is needed again. Be sure to make note of
the storage "Do's and Do Not's" listed on this page. At
least once a year or the heater has been used in a dusty
environment, it is recommended that the blower wheel
be thoroughly cleaned. Start by removing the access
panel cover on the blower side of the heater. There are
8 screws on the HS115SF and 14 Screws on the larger
HS190SF and HS250SF (4 and 7 on each side respectively)
holding the panel in place.
Once you have access to the blower motor mounting
plate remove the motor and wheel then use compressed
air to blow off the wheel. If a more aggressive cleaning
method is required to get the wheel clean you can
remove the wheel from the motor by loosening the set
screw. Water solvents and cleaners can then be utilized to
complete the cleaning. Re install the blower in the reverse
it was removed.
DO NOT....
• Do not store the unit outside.
• Do not lose the components shipped with your
heater.
• Do not store your heater in an area prone to rodents.
They can damage internal wiring and the nesting
material is a fire hazard. Always open and inspect
your heater for signs of insect and rodents before
use especially after long bouts of storage.
STORAGE UNIT AVAILABLE FOR THE HS190SF
& HS250SF
1
2
3
4
5
6
7
8
9
8 SCREWS
4 ON EACH SIDE
11
22
33
44
FIGURE 9
FIGURE 10
FIGURE 11
10
Forced-Air Single-Fuel NOMAD Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
PROPANE TANK SIZE SELECTION
Below are a few quick points of reference for when you
need to select propane cylinders for your applications.
There are two major points to consider. What is the
temperature outside? & What are the BTU requirements
of the heater I will be using. While 20lb, 40lb and 100lb
tanks are the most common tank sizes, there are various
other options available. Contact you propane supplier for
details.
LBS OF LP IN THE CYLINDER
MAXIMUM CONTINUOUS BTU OUTPUT PER HOUR
@ VARIOUS TEMPERATURES
0°F (-18°C) 20°F(-7°C) 40°F (4°C)
200 (2 x 100's) 226,000 334,000 428,000
100 113,000 167,000 214,000
80 (2 x 40's) 94,000 137,000 180,000
40 55,000 79,000 105,000
20 36,000 51,000 69,000
PROPANE TANK SELECTION @ 20°F (-7°C)
HIGH SETTING LOW SETTING
HS115SF 110,833 BTU/HR 80,612 BTU/HR
2 X 40LB TANKS 1 X 40LB TANK
HS190SF 190,200 BTU/HR 127,100 BTU/HR
2 X 100LB TANKS 2 X 40LB TANKS
HS250SF 248,625 BTU/HR 181,119 BTU/HR
2 X 100LB TANKS 2 X 100LB TANKS
EXAMPLE TANK SELECTION
20LBS 40LBS 100LBS
18”
29”
48”
12.5”
12.5”
14.5”
SERVICE & REPAIR
A hazardous condition may result if a heater is used that
has been modified or is not functioning properly.
When the heater is working properly:
• The flame is contained within the heater.
• The flame is essentially blue with perhaps some
yellow tipping.
• There is no strong disagreeable odor, eye burning or
other physical discomfort.
• There is no smoke or soot internal or external to the
heater.
• There are no unplanned or unexplained shut downs
of the heater.
• The parts lists and wiring diagram show the heater
as it was constructed. Do not use a heater which is
different from that shown. In this regard, use only
the hose, regulator and cylinder connection fitting
(called a POL fitting) supplied with the heater.
• (3) of the four lights on the side of the heater should be
illuminated (Heat, Power, Fan Running) per Figure 12.
For this heater, the regulator must be set as shown in
“SPECIFICATIONS”. If there is any uncertainty about the
regulator setting, have it checked. A heater which is not
working right must be repaired, but only by a trained,
experienced service person. The heater is equipped with
a 1 year Limited Warranty, for full warranty information
please read page 20. Please include a brief statement
indicating date, place of purchase, the nature of the
problem and proof of purchase for warranty inquiries.
Out-of-warrranty products can be repaired with a charge
for parts and labor. Contact customer service for a list of
certified repair centers near you.
FIGURE 12
Operating Instructions and Owner’s Manual
11
Forced-Air Single-Fuel NOMAD Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
Symptom Troubleshooting
Blower does not come on 1. Make sure the switch is either in the "POWER ON" or "FAN
ONLY" positions.
2. Verify the extension cord being used is not too long.
3. Check power source is 110 V.
4. Verify the setting on the thermostat is higher than the
temperature in the space to be heated.
Blower runs but the burner does not ignite 1. Make sure the switch is in the "POWER ON" position and
not in the "FAN ONLY" position.
2. Verify that the fuel connected to the unit is turned on and
flowing. It may take a few cycles to get all the air out of
the lines.
3. Make sure the rate selection valve is in the desired position
for the setting (HI or LO) that you desire.
Unit producing little heat or no heat. 1. Make sure the switch is in the "POWER ON" position and
not the "FAN ONLY" position.
2. Make sure the rate selection valve is in the desired position
for the setting (HI or LO) that you desire.
3. Verify that the fuel pressure being supplied to the heater is
adequate. Refer to the specification table in this manual for
required pressures.
4. Make sure the factory supplied hose and regulator are
being used.
Heater will not shut down 1. Verify the switch is in the "POWER OFF" position and not in
the "POWER ON" or "FAN ONLY" positions.
2. Check current setting on the thermostat. Is it set to a
temperature higher than the space being heated?
3. Heater will only cycle on and off when optional thermostat
is installed.
Unit will not turn on with thermostat installed 1. Verify that the thermostat is installed correctly. Heater will
only cycle on and off when the optional thermostat is
installed.
2. Verify the setting on the thermostat is higher than the
temperature in the space to be heated.
3. Check that the power switch is in the "POWER ON"
position. The thermostat will only cycle on and off if the
power switch is in the "POWER ON" position.
Unit will not turn off with thermostat installed. 1. Verify the setting of the thermostat is lower than the
temperature in the space being heated.
2. Verify that the thermostat is installed correctly, the unit
may just be on the on position.
3. Heater may be undersized or for the space being heated.
Red HLS fault light is on (Figure 12) 1. Verify that the path of heat is not obstructed.
2. Check for blockage in the duct and at the end diffuser
FOR FURTHER ASSISTANCE
If after you have reviewed the trouble shooting in this
manual and you still require assistance please use any of
the following methods to contact our technical service
department. We will do our absolute best to resolve any
issues or problems that arise. Most problems can be solved in
just a few minutes.
HOURS ARE: Monday- Friday 8:00am until 5:00pm
CALL: 866-447-2194
FAX: 800-321-0552
VISIT: HEATSTARBYENERCO.COM
INQUIRIES IN CANADA ONLY
PLEASE CALL: 877-477-3353
VISIT IPSPOWER.COM
12
Forced-Air Single-Fuel NOMAD Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
WIRING DIAGRAM-ALL UNITS
SW1
L
1
2
2A
1B
1A
2B
ign
n/c
n/c
6
5
4
3
2
1
G
VP
N
L
N
led 2
chassis
ground
G
T1
24vac
sail
switch
led 5
Gas
Valve
GV1
Chassis wiring is stranded 18 AWG / 105 C / @ 600 Volts
Igniter wiring is16 AWG / 25KVDC / 10 KVAC
(replace with same ratings)
(all quick connects fully insulated)
SW3
M
M1
led 1
SW4
hls
led 4
Operating Instructions and Owner’s Manual
13
Forced-Air Single-Fuel NOMAD Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
WARNING
Air Quality Hazard
• Do not use this heater for heating human living quarters.
• Use of direct-fired heaters in the construction environment can result in exposure to levels of CO, CO2, and NO2 considered
to be hazardous to health and potentially life threatening.
• Do not use in unventilated areas.
• Know the signs of CO and CO2 poisoning.
• Headaches, stinging eyes
• Dizziness, disorientation
• Difficulty breathing, feels of being suffocated
• Proper ventilation air exchange (OSHA 29 CFR 1926.57) to support combustion and maintain acceptable air quality shall be
provided in accordance with OSHA 29 CFR Part 1926.154, ANSI A10.10 Safety Requirements for Temporary and Portable
Space Heating Devices and Equipment used in the Construction Industry or the Natural Gas and Propane Installation Codes
CSA B149.1.
• Periodically monitor levels of CO, CO2 and NO2 existing at the construction site – at the minimum at the start of the
shift and after 4 hours.
• Provide ventilation air exchange, either natural or mechanical, as required to maintain acceptable indoor air quality.
USA 8-Hr Time weighted average
(OSHA 29 CFR 1926.55 App A)
Canada 8-hr time weighted average
WorkSafe BC OHS Guidelines Part 5.1
and Ontario Workplaces Reg 833
CO 50 ppm 25 ppm
CO25000 ppm 5000 ppm
NO23 ppm (Reg 833)
USA – Ceiling Limit
(Short Term Exposure Limit = 15 minutes)
Canada STEL (15 minutes Reg 833/1 hour
WSBC) WorkSafe BC OHS Guidelines Part
5.1 and Ontario Workplaces Reg 833
CO 100 ppm
CO2
15000 ppm (WSBC)
30000 ppm (Reg 833)
NO25 ppm 1.0 ppm (WorkSafeBC)
5.0 ppm (Reg 833)
• Ensure that the flow of combustion and ventilation air exchange cannot become obstructed.
• As the building ‘tightens up’ during the construction phases ventilation may need to be increased.
Installation of this appliance at altitudes above 2000 ft (610 m) shall be in accordance with local codes, or in the absence of local
codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or National Standard of Canada, Natural Gas and Propane Installation
Code, CSA B149.1
14
Forced-Air Single-Fuel NOMAD Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
1
2
511
4
9
10
8
6
11
7
12
13
14
15
16
17
19
18
20
22
21
23
24
25
26
27
29
28
41
42
34
35
33
38
36
37
32
40
39
43
# P/N PART DESCRIPTION QTY
1 60801 HEATER FOOT 2
2 60800 HEATER BASE 1
4 60818 COMBUSTION CHAMBER -RIGHT 1
5 60820 COMBUSTION CHAMBER -BACK 1
6 60817 COMBUSTION CHAMBER -LEFT 1
7 60819 COMBUSTION CHAMBER -TOP 1
8 60822 COMBUSTION CHAMBER -UPPER FLANGE 1
9 60821 COMBUSTION CHAMBER -LOWER FLANGE 1
10 60823 LOWER BURNER COVER 1
11 60824 COMBUSTION CHAMBER - HEAT SHIELD 2
12 60813 INSIDE BLOWER PANEL 1
13 60815 BLOWER TUBE 1
14 60816 115 BLOWER WHEEL 1
15 60812 OUTSIDE BLOWER PANEL 1
16 60814 MOTOR MOUNTING PLATE 1
17 60843 115 MOTOR - 1/3HP 1
18 00613 SAIL SWITCH 1
19 00613 SAIL SWITCH BRACKET 1
20 60958 HIGH LIMIT SWITCH 1
21 60833 HEATER COVER 1
22 60835 MOTOR DOOR 1
23 60834 CONTROLS DOOR 1
# P/N PART DESCRIPTION QTY
24 60837 DOOR HINGE 1
25 60839 D-RING LATCH/LOCK 1
26 60847 24V RED LED LAMP - FAULT INDICATOR 1
27 60846 24V GREEN LED LAMP - GAS VALVE ON INDICATOR 1
28 60845 120V LED LAMP - GREEN 2
29 60841 MAIN POWER ROCKER SWITCH 1
32 27808 FLAME CONTROL BOARD 1
33 60810 115 BURNER 1
34 60827 115 IGNITER BURNER PLATE-FRONT 1
35 60729 IGNITER/FLAME SENSE ASSY. 1
36 60831 115 BURNER R CLAMP 1
37 60832 115 BURNER CLAMP BASE 1
38 60826 115 IGNITER BURNER PLATE-BLACK 1
39 00620 GAS TRAIN ASSY, HS115SF 1
40 60129 GAS VALVE 1
41 60784 SECONDARY ORIFICE/VALVE, HS115SF 1
42 60809 ORIFICE HOLDER 1
43 60781 MAIN ORIFICE, HS115SF 1
** 60969 HOSE,ASSY,NOMAD,15',1/2"MP,1/2"FF 1
** 00617 REGULATOR W/ POL 1
** 00618 THERMOSTAT ASSEMBLY W/ CORD 1
EXPLODED VIEW HS115SF
** NOT SHOWN
Operating Instructions and Owner’s Manual
15
Forced-Air Single-Fuel NOMAD Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
17
29
16
38
36
35
32
34
33
31
11
10
28
27
13
14
12
19
22
24
23
25
26
18
30
21 20
2
6
7
8
1 9
3
45
15
37
# P/N PART DESCRIPTION QTY
1 60973 190 COVER 1
2 60904 ELECTRICAL DOOR 1
3 60905 MOTOR DOOR 1
4 60906 FIXED PIECE HANDLE MOUNT 1
5 60908 HANDLE 1
6 60916 DOOR HANDLE 1
7 60913 DOOR HANDLE SPACER 1
8 60917 DOOR LATCH 1
9 60915 HOIST RINGS 4
10 60884 BASE 1
11 60901 BASE FOOT 1
12 27808 FLAME CONTROL BOARD 1
13 40940 WHEEL 2
14 60902 AXEL 1
15 28787 WHEEL HARDWARE KIT 1
16 60851 SAIL SWITCH 1
17 60938 SAIL SWITCH BRACKET 1
18 60922 COMBUSTION CHAMBER-TOP 1
19 60891 COMBUSTION CHAMBER-LEFT 1
20 60890 COMBUSTION CHAMBER-RIGHT 1
21 60923 COMBUSTION CHAMBER-RIGHT HEAT SHIELD 1
22 90924 COMBUSTION CHAMBER-LEFT HEAT SHIELD 1
# P/N PART DESCRIPTION QTY
23 60892 COMBUSTION CHAMBER-TOP FLANGE 1
24 60893 COMBUSTION CHAMBER-BOTTOM FLANGE 1
25 60925 BURNER STAND-OFF 1
26 60885 COMBUSTION CHAMBER-LOWER HEAT SHIELD 1
27 60974 BLOWER SHELF 1
28 60975 BLOWER SHELF SUPPORT 1
29 60899 HIGH LIMIT SWITCH 1
30 60894 COMBUSTION CHAMBER SUPPORT 2
31 60977 HOUSING RIGHT SIDE 1
32 60978 BLOWER TUBE 1
33 60981 HOUSING DEFLECTOR ATTACHMENT 1
34 60980 HOUSING INLET ADAPTER 1
35 60976 HOUSING LEFT SIDE 1
36 60979 MOTOR MOUNT 1
37 60998 190 BLOWER WHEEL 1
38 60971 1/2HP MOTOR, 190 1
** 60928 IGNITER BURNER PLATE-FRONT, HS190SF/HS250SF 1
** 60729 IGNITER/FLAME SENSE ASSY 1
** 60969 HOSE,ASSY,NOMAD,15',1/2"MP - 1/2"FF 1
** 00617 REGULATOR W/ POL 1
** 00618 THERMOSTAT ASSEMBLY W/ CORD 1
EXPLODED VIEW HS190SF
** NOT SHOWN
16
Forced-Air Single-Fuel NOMAD Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
NOTES:
Operating Instructions and Owner’s Manual
17
Forced-Air Single-Fuel NOMAD Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
EXPLODED VIEW HS250SF
# P/N PART DESCRIPTION QTY
1 60903 250 COVER 1
2 60904 ELECTRICAL DOOR 1
3 60905 MOTOR DOOR 1
4 60906 FIXED PIECE HANDLE MOUNT 1
5 60908 HANDLE 1
6 60916 DOOR HANDLE 1
7 60913 DOOR HANDLE SPACER 1
8 60917 DOOR LATCH 1
9 60915 HOIST RINGS 4
10 60900 BASE 1
11 60901 BASE FOOT 1
12 27808 FLAME CONTROL BOARD 1
13 40940 WHEEL 2
14 60902 AXEL 1
15 28787 WHEEL HARDWARE KIT 1
16 00673 SAIL SWITCH 1
17 60938 SAIL SWITCH BRACKET 1
18 60922 COMBUSTION CHAMBER-TOP 1
19 60919 COMBUSTION CHAMBER-LEFT 1
20 60918 COMBUSTION CHAMBER-RIGHT 1
21 60923 COMBUSTION CHAMBER-RIGHT HEAT SHIELD 1
22 60924 COMBUSTION CHAMBER-LEFT HEAT SHIELD 1
# P/N PART DESCRIPTION QTY
23 60920 COMBUSTION CHAMBER-TOP FLANGE 1
24 60921 COMBUSTION CHAMBER-BOTTOM FLANGE 1
25 60925 BURNER STAND-OFF 1
26 60885 COMBUSTION CHAMBER-LOWER HEAT SHIELD 1
27 60930 BLOWER SHELF 1
28 60931 BLOWER SHELF SUPPORT 1
29 60958 HIGH LIMIT SWITCH 1
30 60894 COMBUSTION CHAMBER SUPPORT 2
31 60933 HOUSING RIGHT SIDE 1
32 60934 BLOWER TUBE 1
33 60937 HOUSING DEFLECTOR ATTACHMENT 1
34 60936 HOUSING INLET ADAPTER 1
35 60932 HOUSING LEFT SIDE 1
36 60935 MOTOR MOUNT 1
37 60940 250 BLOWER WHEEL 1
38 60960 3/4 HP MOTOR, 250 1
** 60928 IGNITER BURNER PLATE-FRONT, HS190SF/HS250SF 1
** 60729 IGNITER/FLAME SENSE ASSY 1
** 60969 HOSE,ASSY,NOMAD,15',1/2"MP - 1/2"FF 1
** 00617 REGULATOR W/ POL 1
** 00618 THERMOSTAT ASSEMBLY W/ CORD 1
194
5
3
7
6
2
8
21
20
18
26
23
24
19
2227
28
12 14
13 11
10
31
34
32
35
16
17
29
37
36
33
30
15
38
** NOT SHOWN
18
Forced-Air Single-Fuel NOMAD Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
NOTES:
Operating Instructions and Owner’s Manual
19
Forced-Air Single-Fuel NOMAD Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
# P/N PART DESCRIPTION QTY
1 60129 HONEYWELL GAS VALVE 1
2-A 60785 SECONDARY ORIFICE/VALVE, HS190SF 2
2-B 60786 SECONDARY ORIFICE/VALVE, HS250SF 1
3 60948 ORIFICE HOLDER 1
# P/N PART DESCRIPTION QTY
4-A 60782 MAIN ORIFICE, HS190SF 1
4-B 60783 MAIN ORIFICE, HS250SF 1
5-A 00650 GAS TRAIN ASSY, HS190SF 1
5-B 00680 GAS TRAIN ASSY, HS250SF 1
WARNING:
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY
OTHER PARTS COULD CAUSE INJURY OR DEATH. REPLACEMENT
PARTS ARE ONLY AVAILABLE DIRECT FROM THE FACTORY AND
MUST BE INSTALLED BY A QUALIFIED SERVICE AGENCY.
FOR SERVICE OR PARTS INQUIRIES
PLEASE CALL: 866-447-2194 OR 216-916-3000
VISIT: WWWHEATSTARBYENERCO.COM
INQUIRIES IN CANADA ONLY
PLEASE CALL: 877-477-3353
VISIT IPSPOWER.COM
COROPORATE ADDRESS
HEATSTAR BY ENERCO
4560 WEST 160TH STREET
CLEVELAND, OHIO 44135
OUR OFFICE HOURS ARE 8:00 AM - 5:00 PM EST MONDAY-FRIDAY
WHEN CONTACTING US:
PLEASE HAVE YOUR SERIAL NUMBER AND MODEL NUMBER HANDY.
THESE CAN BOTH BE LOCATED ON THE RATING LABEL LOCATED ON
THE INSIDE OF THE ACCESS PANEL.
RETAIN THIS MANUAL FOR FUTURE REFERENCE.
Gas Train for HS190SF & HS250SF
1
2
3
4
5
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
WARNING:
USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS
COULD CAUSE INJURY OR DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE DIRECT
FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE AGENCY.
PARTS ORDERING INFORMATION:
PURCHASING: Accessories may be purchased at any HEAT STAR local dealer or direct
from the factory
FOR INFORMATION REGARDING SERVICE
Please call Toll-Free 866-447-2194 • HEATSTARBYENERCO.COM
Our office hours are 8:00 AM – 5:00 PM, EST, Monday through Friday.
Please include the model number, date of purchase, and description of problem in all
communication.
LIMITED WARRANTY
The company warrants this product to be free from imperfections in material or
workmanship, under normal and proper use in accordance with instructions of
The Company, for a period of one year from the date of delivery to the buyer. The
Company, at its option, will repair or replace products returned by the buyer to the
factory, transportation prepaid within said one year period and found by the Company
to have imperfections in material or workmanship.
If a part is damaged or missing, call our Technical Support Department at 866-447-2194.
Address any Warranty Claims to the Service Department, HEAT STAR Group, Inc.,
4560 W. 160th St., Cleveland, Ohio 44135. Include your name, address and telephone
number and include details concerning the claim. Also, supply us with the purchase
date and the name and address of the dealer from whom you purchased our product.
The foregoing is the full extent of the responsibility of the Company. There are no
other warranties, express or implied. Specifically there is no warranty of fitness for a
particular purpose and there is no warranty of merchantability. In no event shall the
Company be liable for delay caused by imperfections, for consequential damages, or
for any charges of the expense of any nature incurred without its written consent. The
cost of repair or replacement shall be the exclusive remedy for any breach of warranty.
There is no warranty against infringement of the like and no implied warranty arising
from course of dealing or usage of trade. This warranty will not apply to any product
which has been repaired or altered outside of the factory in any respect which in our
judgment affects its condition or operation.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This Warranty gives
you specific legal rights, and you may have other rights which vary from state to state.
HEAT STAR Group, Inc. reserves the right to make changes at any time, without notice or
obligation, in colors, specifications, accessories, materials and models.
OPERATING INSTRUCTIONS
AND OWNER’S MANUAL
READ INSTRUCTIONS CAREFULLY: Read and follow all instructions. Place instructions in a safe
place for future reference. Do not allow anyone who has not read these instructions to assemble,
light, adjust or operate the heater.
Model #
PRODUCT REGISTRATION: Thank you for your purchase.
Please log in to HEATSTARBYENERCO.COM to register your product.
HS115SF
HS190SF
HS250SF
ENERCO GROUP, INC., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 1-866-447-2194
Heatstar is a registered trademarks of Heatstar, Inc.
© 2020, Heatstar. All rights reserved
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
HeatStar HS115SF Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: HeatStar HS115SF Owner's manual
- español: HeatStar HS115SF El manual del propietario
Documents connexes
-
HeatStar HS115TC Le manuel du propriétaire
-
-
-
-
-
-
-
Autres documents
-
Mr. Heater MH38QFA Le manuel du propriétaire
-
Power Fist 8677486 Le manuel du propriétaire
-
DeWalt DXH125FAVHC Guide d'installation
-
-
-
-
Empire Heating Systems Vented Counterflow Wall Furnace (FAW40) Le manuel du propriétaire
-
-
WilTec 60317 Manuel utilisateur