Ohaus ST3100-B Manuel utilisateur

STARTER 3100

Bench pH Meter

Instruction Manual

Manual de instrucciones

del pHmetro de mesa

STARTER 3100

PH-mètre de laboratoire

Manuel d’instructions

STARTER 3100

Medidor de pH de Bancada

Manual de Instruções

TABLE OF CONTENTS

1 INTRODUCTION ................................................................... 1

1.1 Definition of Signal Warnings and Symbols ...................................... 1

1.2 Safety Precautions ............................................................................ 2

1.3 Display and controls .......................................................................... 3

2 INSTALLATION ..................................................................... 5

2.1 Package contents .............................................................................. 5

2.2 Installing the stand-alone electrode holder ....................................... 6

2.3 Installing the power adapter .............................................................. 6

2.4 Connect the pH electrodes ................................................................ 7

2.5 Meter stand for adjusting view angle ................................................. 7

2.6 Attached quick guide ......................................................................... 7

3 SETUP ................................................................................... 8

3.1 Set temperature unit and MTC value ................................................ 8

3.2 Selecting a predefined buffer group .................................................. 8

4 STARTER 3100 OPERATION ............................................... 9

4.1 Calibration ......................................................................................... 9

4.1.1 Buffer group ................................................................................... 9

4.1.2 Performing 1-point calibration ..................................................... 10

4.1.3 Performing 2-point calibration ...................................................... 11

4.2 Sample measurement ..................................................................... 12

4.2.1 pH measurement ......................................................................... 12

4.2.2 mV measurement ........................................................................ 12

4.3 Temperature measurement ............................................................. 12

4.4 Using the memory ........................................................................... 12

4.4.1 Storing a reading ......................................................................... 12

4.4.2 Recalling from memory ............................................................... 12

4.4.3 Clearing the memory ................................................................... 13

4.5 Printing ............................................................................................ 13

5 MAINTENANCE .................................................................. 15

5.1 Error message ................................................................................. 15

5.2 Meter maintenance.......................................................................... 15

5.3 Electrode maintenance ................................................................... 16

5.4 Self-diagnosis .................................................................................. 16

5.5 Recover factory settings .................................................................. 16

6 TECHNICAL DATA .............................................................. 17

6.1 Specifications .................................................................................. 17

6.2 Compliance ..................................................................................... 18

7 BUFFER GROUP ................................................................ 19

STARTER 3100 Bench pH Meter EN-1

1 INTRODUCTION

Thank you for choosing OHAUS.

Please read the manual completely before using the STARTER 3100 bench pH meter to ensure

proper setup, operation and maintenance.

STARTER 3100 has an excellent performance/price ratio and is designed with many useful features

including a stand-alone electrode holder and a beeper for error alert. Other accessories such as

pH electrodes and buffer solutions are also available.

STARTER 3100 offers many practical features and functions such as:

 Large backlit LCD with Quick Guide attached under the meter to assist with user operation

 Stand-alone electrode holder for maximum flexibility

 Electrode condition icon automatically showing you the health of your pH electrode

 RS232 port and memory to store up to 99 measurements

1.1 Definition of Signal Warnings and Symbols

Safety notes are marked with signal words and warning symbols. These show safety issues and

warnings. Ignoring the safety notes may lead to personal injury, damage to the instrument,

malfunctions and false results.

Signal Words

WARNING For a hazardous situation with medium risk, possibly resulting in

injuries or death if not avoided.

CAUTION For a hazardous situation with low risk, resulting in damage to the

device or the property or in loss of data, or injuries if not avoided.

Attention For important information about the product.

Note For useful information about the product

Warning Symbols

General hazard

Explosion hazard

Corrosive hazard



Alternating current



Direct current

EN-2 STARTER 3100 Bench pH Meter

1.2 Safety Precautions

CAUTION: Read all safety warnings before installing, making connections, or servicing this

equipment. Failure to comply with these warnings could result in personal injury and/or property

damage. Retain all instructions for future reference.

 Verify that the input voltage range printed on the data label and the plug type matches the

local AC power to be used.

 Make sure that the power cord does not pose a potential obstacle or tripping hazard.

 Use the equipment only in dry locations.

 Dry off any liquid spills immediately. The instrument is not watertight.

 When using chemicals and solvents, comply with the instructions of the chemical producer

and the general lab safety rules.

 Use only approved accessories and peripherals.

 Operate the equipment only under ambient conditions specified in these instructions.

 Disconnect the equipment from the power supply when cleaning.

 Do not operate the equipment in hazardous or unstable environments.

 Service should only be performed by authorized personnel.

STARTER 3100 Bench pH Meter EN-3

1.3 Display and controls

Displays

1

Electrode condition

Slope: more than 95%

and offset: ± (0-15) mV

Electrode condition is good

Slope: 90-95%

or offset: ± (15-35) mV

Electrode condition is

acceptable

Slope: less than 90%

or offset: ± (35-60) mV

Electrode condition is not

good or needs cleaning

2

Endpoint stability icon ; Auto endpoint icon

3

Measurement icon - ; means measurement or calibration is running when blinks

4

Calibration icon - ; means calibration in progress when display

5

Setup icon - ; instrument is in the setup mode, can set temperature(MTC), buffer group

etc.

6

pH/mV reading or slope in calibration process

7

Calibration point / Buffer group /Memory number / Error index

8

Auto temperature compensation - ATC ; Manual temperature compensation - MTC

9

Temperature during measurement or offset (mV) in calibration process

2

3

4

1

5

7

8

9

1

2

3

4

5

6

EN-4 STARTER 3100 Bench pH Meter

Controls

Button

Press & release

Press & hold

for 3 seconds

- Start or finish measurement

- Confirm setting, store entered

value

- Turn auto endpoint on / off

,

- Start calibration

- Recall the latest calibration

data : slope and offset

- Meter turn on

- Exit and return to measurement

screen

- Meter turn off

- Store current reading to memory

- Increase value during setting

- Scroll up through the memory

- Recall stored data

- Print current memory data

- Switch between pH and mV

- Decrease value during setting

- Scroll down through the memory

- Enter setup mode

- Start self-diagnosis

Turn on/turn off the backlight

of the LCD

STARTER 3100 Bench pH Meter EN-5

2 INSTALLATION

Carefully unpack the box.

2.1 Package contents

The model ST3100-B (basic package) has the following items:

In addition to ST3100-B content, the ST3100-F package also includes the following:

In addition to ST3100-B content, the ST3100-H package also includes the following:

Each pH buffer powder should be dissolved in 250ml pure water or deionized water in a

volumetric flask.

Additional electrodes available include the following:

Model

Description

P/N

ST310

3-in-1 plastic refillable pH Electrode

83033965

ST210

2-in-1 plastic refillable pH Electrode

83033966

ST320

3-in-1 plastic gel pH Electrode(no need to fill)

83033967

ST230

2-in 1 glass muddy sample pH Electrode

83033968

STORP1

Gel plastic ORP electrode

30038555

STORP2

Refillable glass ORP electrode

30038553

STTEMP30

Temperature Electrode

83033970

ST3100-B

Units

STARTER 3100

1

Stand-alone electrode holder

1 set

In use cover

1

12V Power supply

1 set

pH Buffer Powder Set (4.01, 7.00, 10.01)

1 set

ST310 3-in-1 refillable pH electrode

1

pH Buffer Powder Set (4.01, 7.00, 10.01)

1 set

ST320 3-in-1 gel pH electrode

1

EN-6 STARTER 3100 Bench pH Meter

Buffers and Accessories:

Buffer powder set (4.01; 7.00; 10.00)

83033971

Buffer pH1.68 250ml

30100424

Buffer pH4.01 250ml

30100425

Buffer pH7.00 250ml

30100427

Buffer pH10.01 250ml

30100429

Buffer pH12.45 250ml

30100430

Electrode holder stand alone (3100/3100C)

30058733

In use cover

30058734

2.2 Installing the stand-alone electrode holder

Install the electrode arm on the base,

After adjusting the tension knob to some extent, you can move the upper arm up and down.

When the pH electrode is installed on the arm, the storage bottle of pH electrode fits into the

base hole.

2.3 Installing the power adapter

Insert the right adapter clip into the power adapter slot. The Ohaus balance power supply is also

12V which could also be used for the pH meter.

STARTER 3100 Bench pH Meter EN-7

2.4 Connect the pH electrodes

There are 3 sockets for electrode. “pH” socket (BNC); “TEMP.” Socket (Cinch) and “REF” Socket

(2mm banana).

For ST310 electrode connect to the BNC and Cinch socket. For 2-in-1 pH electrode (e.g. ST210)

you only need to connect the BNC.

REF socket is for separate reference electrode. (e.g.STREF1)

2.5 Meter stand for adjusting view angle

One unique design of the STARTER 3100 is the meter stand, which can be used to adjust the view

angle of the display in case of working on high table.

2.6 Attached quick guide

Another unique design of the STARTER 3100 is the attached quick guide, the quick guide is

attached into the bottom housing of the meter.

EN-8 STARTER 3100 Bench pH Meter

3 SETUP

3.1 Set temperature unit and MTC value

Please note:

If a temperature electrode is used, Automatic Temperature Compensation (ATC) and the sample

temperature are displayed on the screen. You may then choose to skip MTC setup (below).

If the meter does not detect a temperature electrode or one is not used, the meter automatically

switches to Manual Temperature Compensation (MTC) mode and MTC appears on the screen.

MTC can be set as follows:

 Power the meter on by pressing .

 Press and hold until the setup icon appears on the display and the current

temperature unit blinks (°C or °F).

 Press or to switch between °C and °F.

 Press to confirm your selection.

Then

 Continue with MTC temperature setting by using or to adjust temperature

compensation accordingly

 Press to confirm the setting

 Press to return to the measurement screen.

The default MTC temperature value setting is 25°C (77°F).

Note: °C = 5/9 (°F - 32)

3.2 Selecting a predefined buffer group

After confirming the MTC compensation temperature value, make the buffer group selection. Use

or to select a buffer group among 3 buffer groups (4.1.1). Press to

confirm the setting or press to leave to return to the measurement screen.

The default buffer group is b1.

b1

1.68

4.01

7.00

10.01

STARTER 3100 Bench pH Meter EN-9

4 STARTER 3100 OPERATION

Standard procedure of pH measurement is as follows:

a) pH electrode preparation

b) buffer preparation and pH electrode calibration

c) sample preparation

d) pH measurement

e) Record measurement results or print

f) Rinse the pH electrode and properly store

pH electrode preparation: pH electrode should be rinsed with pure water before and after using.

Check if the electrode is physically damaged. (Be careful with the glass bulb)

The pH electrode should be stored in the storage bottle; the solution in the bottle is 3M KCl

solution. After placing the pH electrode into the sample or buffer solution, user should stir several

seconds then wait 30 to 60 seconds for the signal to stabilize, and then press the button to

operate (Calibration or measurement).

WARNING Do not operate the equipment in hazardous environments. The

equipment is not explosion protected.

WARNING When using chemicals and solvents, comply with the instructions of the

chemical producer and the general lab safety rules.

4.1 Calibration

4.1.1 Buffer group

STARTER 3100 can perform 1-, 2- or 3- point calibrations.

There are 3 buffer groups in the meter, you can select the buffer group you prefer (see 4.3),

default buffer is b1 US standards; the buffer value will be automatically recognized during

calibration. The 3 predefined buffer groups are (at 25°C):

STARTER 3100 automatically corrects for the temperature dependence of the buffer pH values

given in the following table - buffer group b1.

This means, if the buffer solutions’ temperature is 15°C, the calibration value you will get should

be pH1.67 (buffer 1.68), pH4.00 (buffer 4.01), pH7.04(buffer 7.00) and pH10.12 (buffer 10.01).

b1

1.68

4.01

7.00

10.01

b2

2.00

4.01

7.00

9.21

11.00

b3

1.68

4.00

6.86

9.18

12.46

EN-10 STARTER 3100 Bench pH Meter

Calibration: pH electrodes need to be calibrated with pH standard buffer solution before a proper

pH measurement can be made. Calibration is to display the right pH value when meter receive

the mV value signal from the pH electrode.

Slope: the linear coefficient between mV and pH according to theoretical value (e.g. -

59.16mV/pH @ 25 °C which means 100% slope);

Offset: the mV value when pH value is 7.00. (Theoretical value is 0 mV);

4.1.2 Performing 1-point calibration

When performing calibration, Ohaus recommends using Auto End Point Mode. After powering

the meter on, be sure the top of the screen shows to ensure the meter is in Auto End point

Mode.

Auto or Manual End point Mode:

o Press and hold to change the End Point Mode.

o When in Manual Mode, to manually reach a pH measurement or calibration value,

you need to press button- when reading is stable and displays :

then the sample reading or calibration value freezes, blinks 3 times and

freezes on the display.

o When in Auto End Point Mode, the meter determines when the reading is stable

then displays and locks the reading or calibration value automatically, the reading

freezes and blinks 3 times then disappears; blinks 3 times and freezes

on the display.

Note: With the 1-point calibration only the offset is adjusted. If the sensor was previously

calibrated with multi-point calibration the previously stored slope will remain. Otherwise theoretical

100% slope (-59.16 mV / pH) will be used.

5 °C

1.67

4.01

7.09

10.25

10 °C

1.67

4.00

7.06

10.18

15 °C

1.67

4.00

7.04

10.12

20 °C

1.68

4.00

7.02

10.06

25 °C

1.68

4.01

7.00

10.01

30 °C

1.68

4.01

6.99

9.97

35 °C

1.69

4.02

6.98

9.93

40 °C

1.69

4.03

6.97

9.89

45 °C

1.70

4.05

6.97

9.86

50 °C

1.71

4.06

6.96

9.83

STARTER 3100 Bench pH Meter EN-11

When STARTER 3100 is in pH measurement mode (see 4.2); place the pH electrode in a

calibration buffer, stir 5 seconds, wait for 30 seconds, then:

 Press “Cal 1” displays on the bottom left of the screen and “Cal ” is blinking.

and appear on the top of the screen, is blinking during calibration.

 The meter reaches endpoint automatically according to the preselected auto-endpoint

mode, the calibration point pH value (e.g. 7.00) with the temperature display on the screen.

The 1-point calibration is finished; There are now 3 options (OHAUS recommends conducting at

least a 2 point calibration);

1. Press to do the 2-point calibration.

2. Press to store the 1-point calibration and exit, the offset and the slope are

shown on the display for 3 seconds then return to the measurement screen.

3. Press to reject the calibration, return to the measurement screen.

4.1.3 Performing 2-point calibration

 Perform 1-point calibration as described above.

 Rinse the pH electrode with pure water and wipe off with tissue.

 Place the electrode in the next calibration buffer, stir and wait, then press , “Cal 2”

displays on the bottom left of the screen and “Cal ” is blinking. On the top of the screen

and appear, is blinking during calibration.

 The meter reaches endpoint according to the endpoint mode, the calibration point pH value

(e.g. 4.01) with the temperature display on the screen.

The 2-point calibration is finished. There are 3 options:

1. Press to do the 3-point calibration.

2. Press to store the 2-point calibration and exit, the offset and slope are

shown on the display for 3 seconds then return to the measurement screen.

3. Press to reject the calibration, return to the measurement screen.

Note: To perform a 3 point calibration, follow the instructions for performing a 2 point calibration

using a third buffer.

EN-12 STARTER 3100 Bench pH Meter

4.2 Sample measurement

4.2.1 pH measurement

 Place the pH electrode in the sample. Stir for 5 seconds; wait for 30 seconds.

 Press to start the pH measurement, appears on the display. is blinking during

measurement.

 When meter reaches endpoint, the pH value with the temperature display on the screen.

4.2.2 mV measurement

 Press to switch between pH measurement mode and mV measurement mode.

 Follow the same procedure as for pH measurement to perform mV measurement.

4.3 Temperature measurement

For better accuracy, we recommend to use either a built-in or a separate temperature electrode.

 If a temperature electrode is used, ATC and the sample temperature are displayed.

 If the meter does not detect a temperature electrode, it automatically switches to the manual

temperature compensation mode and MTC appears. MTC temperature should be set.

Note: STARTER 3100 accepts NTC 30 kΩ temperature sensor. ATC (Auto Temperature

Compensation) or MTC (Manual Temperature Compensation), the Temperature Compensation

only corrects for the change in the output of the electrode, not for the change in the actual solution.

This means the meter corrects the signal(mV) from the electrode to get a more accurate pH value

according to the real temperature.

4.4 Using the memory

4.4.1 Storing a reading

The STARTER 3100 can store up to 99 endpoint results.

 Press button when the measurement reaches endpoint. M01 indicates that one result

has been stored.

If you press when M99 is displayed, FUL displays to indicate the memory is full. To store

further data you will have to clear the memory. (See 4.4.3)

4.4.2 Recalling from memory

 Press and hold to recall the stored values from memory when the current

measurement reaches endpoint.

STARTER 3100 Bench pH Meter EN-13

 Press button or to scroll through the stored results. R01 to R99 indicates which

result is being displayed.

 Press to exit.

4.4.3 Clearing the memory

 Pressing or to scroll through the stored results until “MRCL” appears.

 Press , CLr blinks;

There are now 2 options:

 Press to confirm the deletion of all the stored data.

 Press to return to the measurement mode without deleting the memory.

4.5 Printing

If the printer is connected to the STARTER 3100(e.g. SF-F40A, green light means connection

success; printer baud rate 9600bps; 8 data bit; none parity bit; 1 stop bit), a print-out is

automatically generated after each end pointed measurement or calibration.

The format for the print-out following a pH measurement is:

End Point, Value, Temp., ATC/MTC

Auto EP, 4.01pH, 25.0 °C, MTC

The details for the second line are:

Auto EP, 4.01pH, 25.0 °C , MTC

| | | |---- Manual Temperature Compensation

| | |---------------- Temperature value and unit ºC

| |------------------------- pH value

|---------------------------------------- Auto End Point

The format for the print-out following a mV measurement is:

End Point, Value, Temp., ATC/MTC

Manual EP, 182mV, 23.2 °C, ATC

The print-out in case of an error message is:

End Point, Value, Temp., ATC/MTC

Error3

The print-out for a 2-point calibration is:

Buffer1: 4.01pH

mV1: 178mV

Temp.1: 25.0 °C

Buffer2: 7.00pH

mV2: 3mV

Temp.2: 25.0 °C

EN-14 STARTER 3100 Bench pH Meter

Slope: 99%

Offset: 5mV

ATC/MTC: MTC

The print-out for a 3-point calibration is:

Buffer1: 4.01pH

mV1: 178mV

Temp.1: 25.0 °C

Buffer2: 7.00pH

mV2: 0mV

Temp.2: 25.0 °C

Buffer3: 9.21pH

mV3: -130mV

Temp.3: 25.0 °C

Slope: 100%

Offset: 0mV

ATC/MTC: ATC

Printing from memory: When scrolling through the memory you can print the entry that is currently

viewed by pressing and holding (3 seconds) the . The printout format is as follows:

Recall 01:

End Point, Value, Temp., ATC/MTC

Manual EP, 4.01pH, 35.6 °C, ATC

STARTER 3100 Bench pH Meter EN-15

5 MAINTENANCE

5.1 Error message

Error 0

Memory access error

Reset to factory settings

Error 1

Self-diagnosis failed

Repeat the self-diagnosis procedure and make

sure that you finish pressing all five keys within

two minutes.

Error 2

Measured values out of range

Check if the electrode is properly connected and

placed in the sample solution.

Error 3

Measured buffer temperature

out of range (<5 or >40 °C)

Keep the pH buffer temperature within the range

for calibration

Error 4

Offset out of range

offset > 60mV or < - 60 mV

Make sure the pH buffer is correct and fresh;

Clean or replace the pH electrode.

Error 5

Slope out of range

Make sure the buffer is correct and fresh; Clean

or replace the pH electrode.

Error 6

Meter cannot recognize the

buffer

Make sure the buffer is correct and fresh; check if

the buffer has not been used more than once.

Error 9

The current data set has

already been stored once

An endpoint reading can only be stored once.

Perform a new measurement to store.

Error 10

The sample temperature out

of range

Check the sample temperature, the temperature

sensor.

If an error happens, the meter will also beep 3 times to alert.

For further technical support please contact Ohaus. (US please contact 1-800-672-7722).

5.2 Meter maintenance

Never unscrew the two halves of the housing!

The STARTER 3100 series instruments do not require any maintenance other than occasional wipe

with a damp cloth and the replacement of depleted batteries.

The housing is made of acrylonitrile butadiene styrene (ABS). This material is attacked by some

organic solvents, such as toluene, xylene and methyl ethyl ketone (MEK). Any spillage should be

immediately wiped off.

EN-16 STARTER 3100 Bench pH Meter

5.3 Electrode maintenance

Make sure the electrode is filled with electrolyte solution. Always store the electrode according to

the electrode instruction manuals and do not allow it to dry out.

If the electrode response becomes sluggish or the slope is not acceptable, try the following:

o Soak the electrode in 0.1M HCl for at least 8 hours.

o For fat or oil contaminant, degrease the membrane with cotton wool soaked in either

acetone or a soap solution.

After electrode treatment, a new calibration should be performed. If the electrode slope is still not

acceptable, the electrode might need to be replaced.

5.4 Self-diagnosis

 When the meter is on, press and hold and simultaneously until the

meter displays the full screen. Each icon blinks one after the other.

This way you may check whether all icons are correctly shown. The next step is to check that the

keys are functioning correctly. This requires user interaction.

When b blinks, five icons are displayed.

 Press the five keys in any order. Each time you press a key an icon disappears from the

screen, continue to press the other keys until all the icons have disappeared.

When the self-diagnosis has been completed successfully, PAS appears. If self-diagnosis fails,

error message Err 1 appears.

Note: You have to finish pressing all five keys within 2 minutes, otherwise Err 1 appears and you

will have to repeat the procedure.

5.5 Recover factory settings

 When the meter is off, press and hold & & together for 3

seconds, the screen displays and blinks, this means “Reset”. There are 2 options:

 Press to reset factory settings (MTC, slope and offset, etc.), display

then restart the meter.

 Or press to quit the setting, display then turn off the meter.

STARTER 3100 Bench pH Meter EN-17

6 TECHNICAL DATA

6.1 Specifications

Ambient conditions

 Indoor use only

 Altitude: Up to 2000 m

 Specified Temperature range: 5 °C to 40 °C

 Humidity: maximum relative humidity 80 % for temperatures up to 30 °C decreasing linearly to

50% relative humidity at 40 °C

 Mains supply voltage fluctuations: up to ±10% of the nominal voltage

 Installation category II

 Pollution degree: 2

 Operability is assured at ambient temperatures between 5 °C to 40 °C

Model

ST3100

Measuring range

-2.00…16.00 pH

–1999…1999 mV

-5 °C…110 °C

Resolution

0.01 pH

1 mV

0.1 °C

Error limits

± 0.01 pH

± 1 mV

± 0.5 °C

Calibration

3 points

3 predefined buffer groups

Memory

99 measurements

The last calibration data

Power supply

AC Adapter Input: 100-240V ~ X.XA 50/60 Hz

AC Adapter Output: 12V  X.XA

Size/weight

220 W x 175 D x 78 H mm / 0.75 kg

Display

Liquid crystal with backlight

Input

BNC, impedance > 10e+12 Ω

Cinch, NTC 30 kΩ

Reference input

2mm banana socket

Temperature-compensation

ATC & MTC

Housing

ABS

La page charge ...

Ohaus ST3100-B Manuel utilisateur

Ce manuel convient également à

Ohaus ST3100-B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents