WAGNER WideShot Le manuel du propriétaire

Marque: WAGNER

Modèle: WideShot

Catégorie: Systèmes de pulvérisation fine Power

Taper: Le manuel du propriétaire

Ce manuel convient également à

Wideshot Power Painter

English

Owner

’

s manual:

Read this manual for complete instructions

1-800-328-8251

Wagner Technical Service

1770 Fernbrook Lane, Plymouth, MN 55447

http://www.wagnerspraytech.com

Visit us on the world wide web!

Table of Contents

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Parts and Components

. . . . . . . . . . . . . . . . . . . . . . . . . .3

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Fluid Container Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Suction Extension Setup . . . . . . . . . . . . . . . . . . . . . . . . .6

Backpack Kit Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Speed Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Flow Control Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Testing the Spray Pattern . . . . . . . . . . . . . . . . . . . . . . . .9

Priming with the Suction Extension . . . . . . . . . . . . . . .10

Overspray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

How to Spray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Using the quick-clean feature (fluid container) . . . . . . . . .12

Using the quick-clean feature (suction extension) . . . . . .13

Cleanup for oil-based materials (fluid container) . . . . . . .14

Cleanup for oil-based materials (suction extension) . . . . .15

Cleaning the Components / Reassembly . . . . . . . . . . .16

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Replacement Parts

. . . . . . . . . . . . . . . . . . . . . . . . . . . .17

roubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Parts List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Need Help? Call us first for answers

fast. Call Wagner Spray Tech toll-free if you

have any comments or problems with this product.

1006 • Form No. 0518803F

Technical service hours: Monday through Friday, 8:00 am to 4:30 pm Central Time

4-Speed

English

Important Safety Information • Read all safety information before

operating the equipment. Save these instructions

HAZARD: INJECTION INJURY

A high pressure stream of paint produced by this equipment

can pierce the skin and underlying tissues, leading to serious

injury and possible amputation.

DO NOT TREAT AN INJECTION INJURY AS A SIMPLE CUT! Injection

can lead to amputation. See a physician immediately.

NOTE TO PHYSICIAN:

Injection into the skin is a traumatic injury. It is important to treat the

injury surgically as soon as possible. DO NOT delay treatment to

research toxicity. Toxicity is a concern with some coatings injected

directly into the blood stream. Consultation with a plastic surgeon or

reconstructive hand surgeon may be advisable.

PREVENTION:

• NEVER aim the gun at any part of the body.

• Do not aim the gun at, or spray any person or animal.

• NEVER allow any part of the body to come in contact with the fluid

stream.

• NEVER put your hand in front of the gun. Wear gloves. Gloves will

not provide protection against an injection injury.

• Keep hands and other body parts away from the discharge. For

example, do not try to stop leaks with any part of the body.

• Always unplug the spray gun before servicing, cleaning tip guard,

changing tips, or leaving unattended.

• ALWAYS use the nozzle tip guard. Do not spray without nozzle tip

guard in place.The tip guard provides some protection against injection

injuries but is mainly a warning device. Only use a nozzle tip specified

by Wagner.

HAZARD: EXPLOSION OR FIRE

Solvent and paint fumes can explode or ignite, causing property

damage and/or severe injury.

PREVENTION:

• Exhaust and fresh air introduction must be provided to keep the air

within the spray area free from accumulation of flammable vapors.

•

void all ignition sources such as static electricity sparks,

open flames, pilot lights, hot objects, cigarettes, and sparks

from connecting and disconnecting power cords or working

light switches.

• Fire extinguishing equipment must be present and in good working

order.

•

Follow the material and solvent manufacturer's safety precautions and

warnings.

• Do not spray flammable or combustable materials near an open flame

or sources of ignition such as cigarettes, motors, and electrical

equipment.

• Know the contents of the paints and solvents being sprayed. Read all

Material Safety Data Sheets (MSDS) and container labels provided

with the paints and solvents. Follow the paint and solvent

manufacturer’s safety instructions.

HAZARD: EXPLOSION HAZARD DUE TO INCOMPATIBLE MATERIALS

ill cause property damage or severe injury

PREVENTION:

• Do not use bleach.

• Do not use halogenated hydrocarbon solvents such as methylene

chloride and 1,1,1 - trichloroethane.

They are not compatible with

aluminum and may cause an explosion. If you are unsure of a

material’s compatibility with aluminum, contact your coating supplier.

HAZARD: HAZARDOUS VAPORS

Paints, solvents, insecticides, and other materials can be harmful

if inhaled or come in contact with the body. Vapors can cause

severe nausea, fainting, or poisoning.

PREVENTION:

• Use a respirator or mask if vapors can be inhaled. Read all

instructions supplied with the mask to be sure it will provide the

ecessary protection.

• Wear protective eyewear.

• Wear protective clothing as required by coating

manufacturer.

HAZARD: GENERAL

Can cause severe injury or property damage.

PREVENTION:

• Read all instructions and safety precautions for equipment and spray

material before operating any equipment.

• Comply with all appropriate local, state, and national codes governing

ventilation, fire prevention, and operation.

• Keep sprayer out of the reach of children.

• Hearing protection is recommended for extended use.

• Always wear appropriate gloves, eye protection and a respirator or

mask when painting.

• Do not operate or spray near children. Keep children away from

equipment at all times.

• Do not overreach or stand on an unstable support. Keep effective

footing and balance at all times.

• Stay alert and watch what you are doing.

• Do not operate the unit when fatigued or under the influence of drugs

or alcohol.

HAZARD: ELECTRIC SHOCK HAZARD

May cause severe injury.

PREVENTION:

• Keep electrical cord plug and spray gun trigger free from paint and

other liquids. Never hold cord at plug connections to support cord.

Failure to observe may result in an electrical shock.

• Never immerse electrical parts in water or any other liquid. Wipe the

exterior of the sprayer with a damp cloth for cleaning. Always make

sure the sprayer is unplugged before taking it apart for cleaning.

NOTE - Use only a 3-wire extension cord that has a 3-blade grounding

plug and a 3-slot receptacle that will accept the plug on the product.

Make sure your extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to carry the current

your product will draw. For lengths less than 50 feet, use a No. 18

WG extension cord. For lengths more than 50 feet, use a No. 14 or

No. 16 AWG extension cord. An undersized cord will cause a drop in

line voltage resulting in loss of power and overheating.

Wagner Spray Tech accessory extension cords recommended:

P/N 0090241

20 foot extension cord

P/N 0090242 35 foot extension cord

To reduce the risks of fire or explosion, electrical shock and the injury to persons, read and understand all instructions included in

this manual. Be familiar with the controls and proper usage of the equipment.

Minimum gauge for extension cords

Cord length (feet)Voltage

Ampere

rating

range

2 - 3

120V

25-50

100 150 200 250 300 400 500

16 14 14 12 12 10 10

(a)

(k)

(l)

(p)

(e)

(f)

(g)

(h)

(i)

(j)

(b)

(c)

(d)

(q)

(n)

(o)

(m)

(q)

(1)

(2)

(3)

(5)

(4)

Grounding Instructions

his product must be grounded. In the event of an electrical short

circuit, grounding reduces the risk of electric shock by providing an

scape wire for the electric current. This product is equipped with a

cord having a grounding wire with an appropriate grounding plug.

he plug must be plugged into an outlet that is properly installed

and grounded in accordance with all local codes and ordinances.

Danger! Improper installation of the grounding plug can result

in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not

connect the green grounding wire to either flat blade terminal. The

wire with insulation having a green outer surface with or without

yellow stripes is the grounding wire and must be connected to the

grounding pin.

WARNING

Check with a qualified electrician or serviceman if the grounding

instructions are not completely understood, or if you are in doubt as

to whether the product is properly grounded. Do not modify the

plug provided. If the plug will not fit the outlet, have the proper

outlet installed by a qualified electrician.

This product is for use on a nominal 120 volt circuit and has a

grounding plug that looks like the plug illustrated below. Make sure

hat the product is connected to an outlet having the same

configuration as the plug.

No adapter should be used with this

product.

Grounded Outlet

Grounding Pin

Cover for grounded outlet box

English

Important Safety Information • Read all safety information before

operating the equipment. Save these instructions

Parts and Components

a) Sprayer assembly

b) Lock-N-Go™ release buttons

c) Spray tip

d) 1 1/2 quart fluid container

e) Speed control switch

f) Flow control knob

g) Trigger

h) Pump housing assembly

1) Piston

2) Spring

3) Pump housing

4) Pump housing ring

5) Swirl valve (2)

i) Extendable handle*

j) Suction set

k) Dual hose set

l) Dual hose fitting

m) Container clip

n) Quick-clean cap

o) Cleaning brush

p) Cleaner / Lubricant**

q) Back pack kit

**included in some models

*Extendable Handle

When you are using the larger, 1 1/2

quart cup, pull out the handle extension.

English

The wide angle tip produces a wide pattern that can be adjusted

horizontally or vertically.

To adjust:

1. Make sure the sprayer is unplugged. Loosen the wide angle

tip by turning the tip counterclockwise 1/4 turn.

2. Turn the adjusting arm so that it is pointing down for a

horizontal pattern

(a). Turn the adjusting arm so that it is

pointing to the side for a vertical pattern

(b).

Tighten the tip firmly by hand.

(a) (b)

Wide Angle Tip (Wide Shot™)

The round tip produces a round pattern. Use a round tip if the

surface you are spraying is too small for use with the wide angle tip.

A round tip is an option included with some models and is available

at your local retailer. Use the size that works best for the type of

aterial you are spraying. The color of the tip center indicates its

size:

Blue (light materials) - .023 inch (0.6mm) opening. This

size works best for oil-based materials.

Pink (medium materials) - .031 inch (0.8mm) opening. This

all purpose size works best for latex materials.

Green (heavy materials) - .039 inch (1.0mm) opening. This

size works best for hard to spray, coarse materials such as

thick latex.

The stain tip is an option included with some models. It has a

specially designed opening for use with thin materials such as thin

stains, sealers and waterproofers, and can be adjusted to reduce

overspray. If you did not receive a stain tip and will be spraying one

of these materials, the tip can be purchased at your local retailer.

The stain tip pattern is round with a fine spray. To adjust the spray

pattern size and coarseness, turn the tip slightly counterclockwise to

narrow the pattern and make the spray more coarse. Turn the tip

slightly clockwise to widen the pattern and make the spray more fine.

Stain Tip

Round Tip

IMPORTANT - Make sure to tighten all spray tips firmly by hand. If the spray tip is not tightened firmly enough, the sprayer could

leak or the tip could be damaged. Do not use a tool to tighten the spray tip. If the tip is too tight, it may be damaged.

•

It is important to mix the material thoroughly before you begin. Do not shake the material to mix it.

Always stir the material

gently but thoroughly before use.

• Remove any skin that has formed on the top of the material. Do not mix the skin into the material. The skin can break up

and clog the sprayer. Older paint may need to be strained.

•

The swirl valve that comes with your sprayer has a clear base. It is to be used with latex and oil-based paints only

• If you will be spraying lacquers, make sure to use the optional swirl valve designed for lacquers, available for purchase by

calling our toll free number. It has a gray base (look in

Accessories for part number).

Selecting the Proper Tip:

Important Preparation Tips:

It is important that you use the proper spray tip based on your type of spraying job and the type of material you plan to spray..

Read below for details.

Important - Before You Begin

English

. Remove the material container from the pump housing by

turning the pump housing locking ring

counterclockwise.

. Press the Lock-N-Go™ buttons on both sides of the

sprayer with one hand, grab the cup with your other hand,

and slide the spray cartridge out.

4. Place a few drops of household oil down the intake (a)

and return openings (b) in the pump housing.

3. Fill the container with the material to be used.

(a) (b)

6. Line up the tab (c) on the pump housing with the notch

(d) on the material container. Twist the pump ring to

thread the cup onto the pump. Plug in the sprayer.

5. Insert the suction set into the intake opening.

7. Take cartridge and slide the rear of the piston into the spray gun. Make sure the pegs (e) on the cartridge line up with the

guides (f) at the bottom of the sprayer. Press cartridge up until it locks into place.

(e)

(f)

Fluid Container Setup

English

2. Remove the material container from the pump housing by

urning the pump housing locking ring

ounterclockwise.

1. Unplug the sprayer. Press the Lock-N-Go™ buttons on

oth sides of the sprayer with one hand, grab the pump

with your other hand, and slide the cartridge out.

Push the dual hose fitting

return openings on the

bottom of the pump

housing. The fitting with

the ridge

(d) goes into the

return opening. Twist the

pump housing ring

(e)

clockwise to tighten the

dual hose fitting into place.

Place a few drops of household oil down the intake

(a)

and return openings (b) in the pump housing.

(a) (b)

(d)

(c)

(e)

6. Push the suction hose set onto the intake and return ports

of the dual hose fitting. The the larger hose

(h) goes onto

the intake (i) port.

5. Take cartridge and slide the rear of the piston into the

spray gun. Make sure the pegs (f) on the cartridge line

up with the guides (g) at the bottom of the sprayer. Press

cartridge up until it locks into place.

(i)

(h)

8. Submerge the suction set assembly into the material

container and attach the container clip (n) to the side to

hold it securely. Make certain that the return line (o) is

inside the container.

7. Slide the intake hose [(j), the larger hose] through the

container clip (k). You may need to pull the hoses slightly

apart.

(k)

(j)

(l)

(m)

(o)

(n)

Push the intake hose

onto the suction set

assembly so that it is

flush with the ridge

(l). Make certain that

the intake filter (m) is

in place on the

suction set.

Suction Extension Setup (optional)

(f)

(g)

English

1. Lay cord seal (a) in backpack lid groove (b). Overlap the

nds of the cord seal by approximately 1/2 inch. Cut off

remaining seal. Lift seal and butt edges together and

ress excess seal into groove.

(a)

(b)

Assemble strap hooks to container using same hole as lid

clip. Adjust strap to fit user.

2. Snap suction tube

bottom of backpack lid. Assemble

backpack kit as shown and secure clip

onto suction hose

(d). When backpack

kit is assembled, follow steps 1-6 in

Suction Extension Setup (previous

age) to attach the kit to the sprayer.

(c)

6. Place lid on container and press firmly into place. Secure

with the tabs

(f).

5. Pour material into back pack to fill line.

Do not fill above

the indicated fill line (e).

(e)

(f)

7. Back pack can either be back- or shoulder-mounted as

shown. Adjust straps to fit user.

Backpack Kit Setup (optional)

(d)

4. If you want to use a backpack liner, install as shown.

English

Speed Control / Flow Control Knob

Your sprayer offers you four speed levels (1 being

lowest, 4 being highest). The lower the speed level, the

closer you can get to your work and the less overspray

you will have.

The spray pattern is controlled by the Flow Control Knob

on the rear of the sprayer, and by the thickness of the

material being sprayed.

8 - 12 inches Medium flow

4 - 8 inches Low to medium flow

6 - 10 inches Medium flow

12 inches

Medium to maximum

flow

NOTE - Do not get the speed control wet or the sprayer could be damaged. Be careful during use and cleanup.

Speed Control:

Flow Control Knob:

Lower speed levels give you greater control but require

more time to cover an area. Depending upon the

thickness of the material or conditions, the settings may

need to be adjusted. Refer to the chart on the right.

To adjust the speed setting, press the button on the

speed control until the light indicates your desired

speed.

SPEED

CONTROL

Turning the flow knob COUNTERCLOCKWISE increases

the amount of material flow. Turning the flow knob

CLOCKWISE decreases the amount of material flow.

English

Testing the Spray Pattern

1. Turn the flow knob fully counterclockwise to maximum

and speed control to 4.

2. Point the sprayer at a scrap piece of wood or cardboard,

and pull the trigger to prime the sprayer. Release trigger

when material sprays evenly from the spray gun.

3. To adjust for your particular spray project, press the

switch on the top of the gun until the sprayer is set at the

desired speed.

4. Turn the flow knob

clockwise until you have a good spray

pattern.

The instructions below will tell you how to achieve the optimum spray pattern by using each of the features illustrated

on the previous page.

5. A poor spray pattern (a) will concentrate the paint in the center of the spray pattern and go on blotchy. A good spray pattern

(b) has an even amount of material throughout the pattern and will go on smoothly.

• Always practice spraying on a piece of scrap wood or

cardboard to test your spray pattern.

•

If you adjust the flow knob and still cannot get a good

pattern, you may need to thin the material you are

using. Always test spraying without thinning the

material. Thin as required to achieve optimum

spraying performance (refer to #5).

•

If you are spraying a material that needs to be thinned,

make sure to follow the manufacturer

’

recommendations.

SPEED

CONTROL

English

Priming with the Suction Extension

• The time needed to prime will vary from 30 seconds to 3 minutes depending upon the thickness of the material you

re spraying.

• If your sprayer is properly cleaned and oiled and it takes longer than three minutes to prime, your piston and/or

pump housing may be worn and will need to be replaced before using your suction set.

• Using the suction extension will decrease the material flow, so it will take longer to apply the same amount of

aterial to the surface being sprayed.

1. If you are using the suction extension, you will need to

prime the sprayer by removing air from the system. To

prime:

Make sure the sprayer is plugged in, and turn the flow

control knob counterclockwise to maximum.

2. Hold the sprayer below the level of the paint. This will

speed up the priming.

3. Aim the sprayer at a piece of scrap wood or cardboard. Squeeze the trigger and hold until all air is out of the system and

material is flowing freely out of the sprayer tip. This could take up to three minutes.

NOTE - The suction set must remain completely submerged

in the material. If it is not completely submerged and air is

sucked into the system, the piston could seize. If the

piston seizes, the sound the gun makes will change to a low

hum and the gun will quickly become hot to the touch.

Never run the sprayer when the piston is seized. Should

this happen, clean the piston and the pump housing

thoroughly using the cleanup procedures found in this

manual.

Overspray

Important

Some sprayed materials create a cloud of paint. Some of that cloud will spray past your intended object and also bounce off of it.

Wind and air currents may cause this cloud to drift onto surfaces not intended to be sprayed. You can control the amount of

overspray and bounce-back by adjusting your flow and moving the sprayer closer to the work piece, but always make sure that

you have a good spray pattern. Always test your pattern on a scrap piece of wood or cardboard, and make sure that you have

drop cloths protecting anything not being sprayed.

ANYTHING YOU DON'T WANT PAINTED THAT IS IN THE AREA OF YOUR SPRAYING SURFACE SHOULD BE COVERED

OR REMOVED.

English

How To Spray

1. Keep your arm moving at constant speed and keep the

sprayer at a constant distance from the surface. The

sprayer should be triggered at the beginning of the stroke

and released at the end of the stroke.

2. Keep the sprayer at right angles to the surface. This

means moving your entire arm back and forth rather than

just flexing your wrist.

eep stroke

even

stroke

tart

stroke

ull

trigger

elease

trigger

ove steadily

proximately

10 to 14 inches

Heavy Coat

Do not flex

wrist while

spraying.

Light Coat Light Coat

NOTE - If material is leaking from the threads of the spray

tip, turn off the sprayer immediately or the sprayer could

be damaged. The sprayer will leak from behind the spray

tip if the swirl valve is not seated properly. If you notice

material leaking from this area:

Never tip the sprayer at more than a 45º angle

when spraying overhead. Material could get

into the motor housing and cause an electric

shock.

3. Unplug the sprayer immediately. Remove the spray tip

by turning it counterclockwise.

4. Remove the swirl valve and see if it needs to be cleaned

or replaced (see page 17). Also check the pump housing

opening for any dirt or other obstruction and clean if

necessary.

Put the swirl valve back in place, making sure it can seat

properly without any obstruction.

Thread on the spray tip by turning it clockwise and tighten

firmly by hand.

English

Using the Quick-clean feature (latex materials only)

Cleaning the Fluid Container

ou will need a garden hose to complete the steps below. If you do not have a garden hose available, or if you used oil-

based materials, follow the Cleanup for Oil-Based Materials

instructions on pages 14-15.

1. Unplug the sprayer. Press the

Lock-N-Go™ buttons on both

ides of the sprayer with one

hand, grab the cup with your

ther hand, and slide the spray

cartridge out.

2. Remove container from pump assembly. Pour the

emaining material back into the original container.

Remove the suction set.

3. Remove all parts from the pump housing assembly.

Place all removed parts (except the pump housing

assembly) into the fluid container. Fit the quick-clean cap

into place on the pump housing ring as shown.

5. SLOWLY turn the garden hose on. Let the water run for

30 seconds. Turn the water off, remove the garden hose

and quick-clean cap from the small container and properly

dispose of the cleaning solution.

BE CAREFUL NOT TO LOSE

ANY OF THE PARTS THAT

ARE STILL IN THE SMALL

CONTAINER!

1545

6. Depending upon the thickness of the material, some

residue may remain on the sprayer parts. Remove any

remaining residue with the cleaning brush and the

appropriate cleaning solution.

7. NOTE - Make sure to completely remove all material

from the inside of the piston chamber by scrubbing

with the brush. Even a small amount of material can

dry like glue and keep the piston from moving,

causing damage to the sprayer.

4. Thread the quick-clean cap and ring onto the container.

Thread a garden hose into the quick-clean cap, and place

entire container and cap into an empty bucket.

8. NOTE - Make sure to keep the vent hole (a) on the

pump housing clean and unblocked or a vacuum can

build up in the container and cause damage to the

sprayer

. A toothpick or straightened paper clip can

be used to clean it.

(a)

NOTE - An empty bucket is needed because water will flow

from the side port (a) of the quick-clean cap when the hose

is turned on.

(a)

Move on to

Reassembly,

page 16.

English

Using the Quick-clean feature (latex materials only)

Cleaning the Suction Extension

ou will need a garden hose to complete the steps below. If you do not have a garden hose available, or if you used oil-

based materials, follow the Cleanup for Oil-Based Materials

instructions on pages 14-15.

1. To purge any remaining material

left in the suction hose, remove the

uction set from the material

container and place into a waste

ontainer.

3. Unplug the sprayer. Press the

Lock-N-Go™ buttons on both sides

of the sprayer with one hand, grab

he pump with your other hand, and

slide the spray cartridge out.

2. Point sprayer into the side of the

waste container. Trigger the

sprayer until nothing more comes

rom the spray tip.

4. Remove piston, spring, spray tip

and swirl valve from the pump

housing assembly. Place all

removed parts into the fluid

container.

6. Fit the quick-clean cap into place on

the pump housing ring as shown.

5. Unlock dual hose fitting (with hoses

still attached) from pump assembly

ring.

7. Push the dual hose fitting

(a) into

the intake and return openings on

the bottom of the quick-clean cap.

The fitting with the ridge

(b) goes

into the return opening.

(a)

(b)

9. SLOWLY turn on the garden hose.

Let the water run for approximately

30 seconds. Turn the water off.

1545

8. Thread a garden hose into the quick-

clean cap. Place hoses (with suction

set attached) into an empty bucket.

10.

Remove the dual hose fitting from the

quick-clean cap.

12. Perform steps 4-8 in Cleaning the

Fluid Container (previous page) in

order to clean the components of

your sprayer

(a)

11. Remove the suction set and dual

hose fitting from the suction hoses.

Place suction set into the fluid

container

English

Title

. Unplug the sprayer. Pour the remaining material back

into the original container.

2. Fill the container half full of the cleaning solution

appropriate to the type of material you sprayed (warm,

soapy water for latex materials, mineral spirits for oil-

based materials).

Move on to

Cleaning the Components

, page 16.

3. Reattach the container and plug in the sprayer. Squeeze

the trigger until the solution comes though the sprayer for

several seconds.

4. Unplug the sprayer. Press the Lock-N-Go™ buttons on

both sides of the sprayer with one hand, grab the cup or

pump with your other hand, and slide the spray cartridge

out.

5. Remove the container and properly dispose of the

remaining solution.

Cleanup for oil-based materials (fluid container)

6. Remove the suction set.

English

Title

. Make sure the sprayer is unplugged.

2. Remove the suction set from the material container and

submerge into a container of the solvent appropriate to

the type of material you sprayed.

Move on to

Cleaning the Components

, page 16.

3. Plug in the sprayer, and squeeze the trigger and spray

into a second container until the solvent coming through

the sprayer is free of material. Unplug the sprayer.

4. Unplug the sprayer. Press the Lock-N-Go™ buttons on

both sides of the sprayer with one hand, grab the cup or

pump with your other hand, and slide the spray cartridge

out.

5. Remove the suction set from the cleaning solution.

Unlock dual hose fitting (with hoses still attached) from

pump assembly ring.

6. Remove the suction set and dual hose fitting from the

suction hoses.

Cleanup for oil-based materials (suction extension)

English

Title

1. Remove all parts from the pump housing assembly.

3. Clean all parts thoroughly with the brush provided using a

solution appropriate to the type of material you sprayed.

Reassembly (all materials)

1. Place the pump housing ring over the piston chamber.

Slide the spring onto the front end of the piston. Insert

the piston into the rear of the piston chamber.

2. Insert swirl valve into front of the piston chamber. Thread

the spray tip onto the pump housing.

3. Line up the tab on the pump housing with the notch in the

material container. Twist the ring to thread the cup onto

the pump.

4. Take spray cartridge and slide the rear of the piston into the spray gun. Make sure the pegs (a) on the cartridge line up with

the guides (b) at the bottom of the sprayer

. Press cartridge up until it locks into place. Pull on the container to make sure

assembly is locked into place.

3. NOTE - Make sure to completely remove all material

from the inside of the piston chamber by scrubbing

with the brush. Even a small amount of material can

dry like glue and keep the piston from moving,

causing damage to the sprayer.

4. NOTE - Make sure to keep the vent hole (a) on the

pump housing clean and unblocked or a vacuum can

build up in the container and cause damage to the

sprayer. A toothpick or straightened paper clip can

be used to clean it.

(a)

(b)

Cleaning the components (oil-based materials)

English

Title

. Turn the sprayer upside-down while the fluid container is

removed. Squeeze a small amount of standard

household oil into both the intake

(a) and return (b)

openings on the pump housing.

(a) (b)

2. Plug in the sprayer. Aim at piece of scrap wood or

cardboard and squeeze the trigger of the sprayer for 2 to

seconds while sprayer is still inverted.

3. Replace the suction set.

Lubricating your sprayer prior to storage is important to prolong the life of the pump housing components.

4. Replace the fluid container.

Replacement Parts

The swirl valve is shaped to cause the material to spin as it

comes out of the sprayer. The spinning breaks the material

up into a fine spray. As more material goes through the swirl

valve, it wears out the valve and the shape of the valve

changes. When it changes too much to produce a good

spray pattern, the valve needs to be replaced.

2 3

Front view of a good swirl valve.

Front view of a swirl valve after spraying 7-10 gallons of

latex paint. Replace.

Front view of a swirl valve after spraying 7-10 gallons of

latex stain. Replace.

Swirl Valve

The average life of a piston and spring will vary depending on

the types of material being sprayed.

Replace the piston if the sprayer takes longer than 15

seconds with the suction set or 3 minutes with the suction

extension to prime when well lubricated, or if there is an

excess amount of material leaking, refer to the

troubleshooting suggestions listed in this manual. Replace

the spring if you notice that it is broken when you clean the

sprayer.

To replace either the swirl valve or the piston and spring,

follow steps 1-3 in Cleaning the Components

(page 16),

and replace the old parts with new ones. When replaced,

follow steps 1-3 in Reassembly

(page 16).

iston and Spring

• Parts of your sprayer wear out with use and require regular replacement. They include the swirl valve, piston and

spring. These parts are not covered by your sprayer warranty.

• More abrasive materials such as latex paints and stains cause these parts to wear out faster than less abrasive

materials such as oil-based paints and stains, thin stains and sealers.

Maintenance

English

TitleTroubleshooting

Problem

Motor will not run.

Motor has a low hum and does

ot spray.

Motor operates properly but does

not spray.

Material spitting or globbing.

Excessive fogging.

Runs and sags in paint.

Material drips from spray tip

guard.

No display on power module

Spraying erratic, module won’t

adjust

Motor overheats.

Material leaking from between

spray tip and locking nut.

Spray cartridge will not lock into

place.

Cause

1. No power at wall outlet. Electrical problem

or defective motor.

1. Control knob turned in too far.

. Seized piston.

1. Failure to prime with 5 ft suction extension.

2.Loose or damaged suction tube.

3. Plugged or worn swirl valve.

4. Swirl valve missing.

5. Material too thick.

6. Plugged spray tip.

7. Intake filter plugged.

8. Control knob needs adjusting.

9. Worn piston.

1. Low on paint.

2. Paint too thick.

oose suction set drawing in air.

4. Worn swirl valve.

5. Worn spray tip.

6. Control knob needs adjusting.

7. Worn piston.

1. Pressure too high.

2. Holding sprayer too far from work surface.

1. Arm movement too slow, holding spray gun

too close to work surface or applying too

much paint at one time.

1. Guard is for safety and cannot be removed.

Some dripping is unavoidable with some

paints.

1. No power.

2. Module defective.

1. Module defective.

1. Seized piston.

2. Extension cord too long.

3. Operating continously

Spray tip is loose.

2. Swirl valve not positioned properly.

Worn swirl valve.

4. Eroded pump housing

1. Piston seized.

Locking mechanism defective.

Solution

1. Try new wall outlet. Take to Authorized Service

Center for repair.

1. Turn control knob counterclockwise.

. Disassemble sprayer and clean.

1. Thin paint. Hold sprayer below level of paint can.

Oil intake opening.

2. Tighten or replace.

3. Clean or replace as needed.

4. Put in swirl valve.

5. Thin material.

6. Clean tip.

7. Clean intake filter.

8. Adjust.

9. Clean and oil or replace.

1. Refill container.

2. Thin paint.

lean and insert firmly in intake opening on pump

housing.

4. Replace swirl valve.

5. Replace if worn.

6. Adjust.

7. Replace or clean and oil.

1. Turn flow control knob

clockwise to reduce

pressure and flow.

2. Hold sprayer closer to work surface.

1. See section on spraying (page 11).

1. Use a small brush on drips that fall on surface

being sprayed. Use a drop cloth.

1. Check to see if plugged in.

2. Take to Authorized Service Center for repair.

1. Take to Authorized Service Center for repair.

1. Clean piston.

2. Replace with proper size.

3. Release trigger at end of pass, allow to cool

ighten securely.

2. Unplug the sprayer, remove the spray tip and

reposition the swirl valve.

Replace.

4. Replace pump housing

1. Clean entire pump assembly thoroughly.

ake to

Authorized Service Center for repair

Additional Repairs

If you have any problems that are not solved by the

troubleshooting section of this manual, please call Wagner

Technical Service at 1-800-328-8251 Monday through Friday

between 8:00 AM and 4:30 PM Central time. If you suspect that

you have a problem with the electrical system, or have any other

problems not solved by the routine maintenance described in this

manual, take your sprayer to the nearest authorized service

center.

Product Registration Card

Send in your product registration card or register online at

www.wagnerspraytech.com. Proper registration will serve as

proof of purchase in the event your original receipt becomes

misplaced or lost. Returning this card will expedite the

processing of your warranty. Be sure you write your unit’s

date code on the card before sending it. The date code is

located at the base of the handle (for example, T087R). The

additional information will also help us to develop new

products that best meet your needs and desires.

ARNING -

Any attempt to open the motor housing or repair any electrical parts within the unit by anyone other than an

authorized repair technician could cause serious injury and will void the warranty

EnglishFrançaisEspañol

Title

a) ---------- Sprayer assembly Pulvérisateur Rociador 1

b) 0518236 Wide Shot™ Spray tip Embout à pulvériser Punta de Wide Shot™

de Wide Shot™ 1

c) 0518231 1 1/2 quart container Réservoir de liquide de Contenedor de 1 1/2 cuarto

1,42 l (48 oz) de galón 1

d) 0518201 Pump housing Corps de pompe Caja de la bomba 1

e) 0518382 Pump housing ring Anneau du corps de pompe Anillo de la caja de la bomba 1

f) 0518235 Suction set Dispositif d’aspiration Unidad de succión 1

g) 0272909 Piston repair kit Trousse de réparation Juego de la reparación del émbolo

de piston 1

h) 0518428 Quick-clean cap Capuchon de nettoyage Tapa de limpieza rápida

rapide 1

i) 0518307 Dual hose fitting Raccord pour tuyau Conexiòn de dos mangueras 1

souple double

j) 0518361 Dual hose set Tuyau souple double Conjunto de dos mangueras 1

k) 0514209 Cleaning brush Brosse de nettoyage Cepillo de limpieza 1

l) 0280353 Container clip Pince pour contenant Gancho del envase 1

m) 0280113 Cleaner / lubricant* Trousse de produits Paquete de limpiador 1

nettoyants/lubrifiants* y lubricante*

n) 0518243 Backpack assembly Ensamble à dos Conjunto de mochila 1

o) 0518448 Suction tube (backpack) Tube d’aspiration (dos) Tube de succión (mochila) 1

p) 0518225

Strap kit Ensemble de courroies Kit de correas 1

Item

Article

Articulo

Part No.

Nº de piéce

Pieza No.

English -

Description

Français -

Description

Español -

Descripción

Quantity

Quantite

Cantidad

Parts list • Liste de pièces • Lista de piezas

(

(b)

(c)

(f) (h)

(

(m)

(i) (k) (l)(j)

(

(e)

(n)

see Optional Accessories for cartridge kits

*voir les Accessoires Optionnels pour des

ensemble de cartouche.

vea los Accesorios Opcionales para los kits

del cartucho.

(o)

(p)

0272117 Lacquer swirl valve Soupape rotative pour produits de laques Válvula en espiral para lacas

0272904 Replacement swirl valves (2) Soupapes rotative de remplacement (2) Válvula en espiral de repuesto (2)

0280113 Cleaner / Lubricant Trousse de produits nettoyants/lubrifiants Paquete de limpiador y lubricante

0272909 Piston repair kit Trousse de réparation de piston Juego de la reparación del émbolo

0272912G

Wide Shot™ spray tip Embout à Wide Shot™ Punta de Wide Shot™

0280037

Stain tip

Embout de teinture

Punta para tinte

0272900

Round tip (blue)

Buse ronde (bleue)

Punta redonda (azul)

0272902

Round tip (pink)

Buse ronde (rose) Punta redonda (rosa)

0272903 Round tip (green) Buse ronde (verte) Punta redonda (verde)

0518119 Six foot suction set Tube d’aspiration de 2 m Tubo de succión de 6 pies (2 m)

0272130 Back pack liners (5) Doublures de sac à dos (5) Cubiertas para mochila (5)

0518112 Wide Shot™ spray cartridge Cartouche de pulvérisation Wide Shot™ Cartucho de rociado Wide Shot™

0518113 Round tip (pink) spray Cartouche de pulvérisation Cartucho de rociado para

cartridge

à buse ronde (rose)

punta redonda (rosa)

05181

14 Stain spray cartridge Cartouche de pulvérisation pour teinture Cartucho para rociado de tinte

Part No.

Nº de piéce

Pieza No.

English -

Description

Français -

Description

Español -

Descripción

Optional Accessories • Accessoires Optional • Accessorios Opciónal

*available in some

models

*disponible dans quelques

modèles

*disponible en algunos

modelos

English

Title

Français Español

Warranty • Garantie • Garantía

GARANTíA LIMITADA POR UN AÑO - Manténgala archivada

Este producto, fabricado por Wagner Spray Tech Corporation (Wagner), está garantizado contra defectos de materiales y de mano de obra por un año a partir de la fecha de compra, si

se utiliza de acuerdo con las instrucciones y recomendaciones especificadas por Wagner. Esta garantía no cubre daños producidos por uso indebido, accidentes, negligencia del usuario

o desgaste normal del producto. Tampoco cubre defectos o daños producidos por reparaciones o mantenimiento no realizados por un Centro de servicio autorizado de Wagner.

CUALQUIER GARANTÍA IMPLÍCITA DE COMERCIALIZACIÓN O DE BUEN ESTADO PARA PROPÓSITOS ESPECÍFICOS ESTÁ LIMITADA POR UN AÑO A PARTIR DE LA FECHA

DE COMPRA. ESTE PRODUCTO SÓLO HA SIDO DISEÑADO PARA USO DOMÉSTICO. SI SE LE DA USO PROFESIONAL Y DE RENTA, ESTA GARANTÍATIENE UNA DURACIÓN

DE 30 DÍAS A PARTIR DE LA FECHA DE COMPRA. BAJO NINGUNA CIRCUNSTANCIA WAGNER SE RESPONSABILIZARÁ POR CUALQUIER DAÑO ACCIDENTAL O COMO

CONSECUENCIA DEL USO DEL PRODUCTO, YA SEA POR LA VIOLACIÓN DE ESTA GARANTÍA O POR CUALQUIER OTRA RAZÓN. ESTA GARANTÍA NO INCLUYE LOS

ACCESORIOS.

Si cualquier producto presentara defectos de materiales y/o de mano de obra durante el período válido, devuélvalo con el recibo de compra y el flete pagado a cualquier Centro de servicio

autorizado de Wagner (este producto viene con una lista de los Centros de servicio). El Centro de servicio autorizado de Wagner reparará o reemplazará el producto (de acuerdo a su

criterio) y se lo devolverá haciendo uso de los gastos de flete ya pagados.

Garantía vitalicia de la boquilla rociadora

La boquilla rociadora que usted ha adquirido con su equipo rociador de pintura Wagner está garantizada contra desgaste por el tiempo que dure su rociador. La garantía de la boquilla no

cubre daños producidos por uso indebido, accidentes o negligencia del usuario.

Si la boquilla falla, debido a desgaste, devuélvala con franqueo pagado a Wagner Spray Tech Corporation, Spray Tip Replacement, 1770 Fernbrook Lane Minneapolis, Minnesota 55447.

Por favor, junto con la boquilla, incluya su nombre, su dirección completa y su número de teléfono. La boquilla se le devolverá en de 6 a 8 semanas.

ALGUNOS EST

ADOS NO PERMITEN LIMIT

ACIONES DE

TIEMPO A LAS GARANTÍAS IMPLÍCITAS NI TAMPOCO LA EXCLUSIÓN DE DAÑOS ACCIDENTALES O COMO

CONSECUENCIA DEL USO DEL PRODUCTO, POR LO QUE ES POSIBLE QUE LA LIMITACIÓN ANTERIOR NO SE APLIQUE A SU CASO PARTICULAR.

EST

A GARANTÍA LE OTORGA CIERTOS DERECHOS LEGALES ESPECÍFICOS Y TAMBIÉN PUEDE ACCEDER A OTROS DERECHOS QUE VARÍAN DE UN ESTADO A OTRO.

GARANTIE LIMITÉE D’UN AN - À conserver

Ce produit, fabriqué par Wagner Spray Tech Corporation (Wagner), est garantit contre les défauts de matériaux et de fabrication pendant un an suivant la date d’achat, s’il

st utilisé conformément aux recommandations et directives imprimées par Wagner. Cette garantie ne couvre pas les dégâts qui résulteraient d’une mauvaise utilisation,

les accidents, la négligence de l’utilisateur ou l’usure normale. Cette garantie ne couvre aucun dégât dû des opérations de maintenance effectuées par tout autre qu’un

réparateur appouvé par Wagner.

OUTE GARANTIE IMPLICITE DE QUALITÉ MARCHANDE OU DE CONFORMITÉ À UN USAGE PARICULIER EST LIMITÉE À UN AN À PARTIR DE LA DATE D’ACHAT. CE

PRODUIT N’EST CONÇU QUE POUR UNE UTILISATION PRIVÉE. D

ANS LE CAS DE LOCATION OU AUTRES APPLICATIONS PROFESSIONNELLES, CETTE GARANTIE SE

LIMITE À

30 JOURS À PARTIR DE LA DATE D’ACHAT. WAGNER NE POURRA EN AUCUN CAS ÊTRE TENUE RESPONSABLE DE DOMMAGES-INTÉRÊTS INDIRECTS OU

CONSÉCUTIFS, QUE CE SOIT POUR UNE RUPTURE DE CETTE GARANTIE OU TOUTE AUTRE RAISON. CETTE GARANTIE NE S’APPLIQUE PAS AUX ACCESSOIRES

Si un produit est défectueux, au niveau des matériaux ou de la fabrication, au cours de la durée applicable de la garantie, le renvoyer avec une preuve d’achat, port payé, à l’un des

centres de service autorisé par Wagner. (Une liste des adresses de ces centres accompagne tous les produits). Le centre de service autorisé réparera ou remplacera le produit (au

choix de Wagner) et le renverra, port payé, et utilisateur.

Garantie à vie de l’embout du pulvérisateur

L’embout livré avec ce produit Wagner est garanti contre l’usure pour toute la durée utile de l’appareil. Cette garantie ne couvre pas les dégâts résultant d’une mauvaise utilisation du

produit, d’accidents ou d’une négligence de l’utilisateur.

Si l’embout du pulvérisateur s’use, le renvoyer, port payé, à Wagner Spray Tech Corporation, Spray Tip replacement, 1770 Fernbrook Lane Minneapolis, Minnesota 55447 (USA).

Prière de joindre le nom, l’adresse et le numéro de téléphone de l’utilisateur. Compter un délai de livraison de 6 à 8 semaines.

CERTAINS ÉTATS OU PROVINCES NE PERMETTENT PAS LA LIMITATIONS DE LA DURÉE DE LA GARANTIE IMPLICITE OU L’EXCLUSION DES DOMMAGES-INTÉRÊTS

INDIRECTS OU ACCESSOIRES, LES RESTRICTIONS APPARAISSANT AUX PRÉSENTES POURRAIT DONC NE PAS S’APPLIQUER À UTILISATEUR.

LA PRÉSENTE GARANTIE CONFÈRE DES DROITS PRÉCIS À UTLISATEUR, MAIS CELUI-CI POURRAIT AVOIR D’AUTRES DROITS EN VERTU DES LÉGISLATIONS LOCALES..

WAGNER ONE-YEAR LIMITED WARRANTY - Keep on File

his product, manufactured by Wagner Spray Tech Corporation (Wagner) is warranted against defects in material and workmanship for one year following date of purchase

f operated in accordance with Wagner’s printed recommendations and instructions. This warranty does not cover damage resulting from improper use, accidents, user’s

negligence or normal wear. This warranty does not cover any defects or damages caused by service or repair performed by anyone other than a Wagner Authorized

ervice Center.

NY IMPLIED WARRANTY OF MERCHANTABlLITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO ONE YEAR FOLLOWING DATE OF PURCHASE.

THIS PRODUCT IS DESIGNED FOR HOME USAGE ONLY. IF USED FOR COMMERCIAL OR RENTAL PURPOSES, THIS WARRANTY APPLIES ONLY FOR 30 DAYS

FROM DATE OF PURCHASE. WAGNER SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER

OR BREACH OF THIS WARRANTY OR ANY OTHER REASON. THIS WARRANTY DOES NOT APPLY TO ACCESSORIES.

If any product is defective in material and/or workmanship during the applicable warranty period, return it with proof of purchase, transportation prepaid, to any Wagner

Authorized Service Center. (A listing of Service Center locations is enclosed with this product.) Wagner’s Authorized Service Center will either repair or replace the product

(

at Wagner’s option) and return it to you, postage prepaid.

pray Tip Lifetime Warranty

The spray tip you have purchased with your Wagner Power Painter is warranted against wear for the life of the Power Painter. The spray tip warranty does not cover

amage resulting from improper use, accidents or user’s negligence.

If the spray tip fails due to wear, return it, postage prepaid, to Wagner Spray Tech Corporation, Spray Tip Replacement, 1770 Fernbrook Lane, Minneapolis, MN 55447.

Please include your name, complete address and telephone number with the spray tip. Allow 6 to 8 weeks for delivery.

OME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL

AMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

whole or in part, in any form.

Wagner Spray Tech Corporation

1770 Fernbrook Lane

Plymouth, MN 55447

Telephone 1-800-328-8251

Warranty • Garantie • Garantía