Jensen Car Stereo System MPX6411 Manuel utilisateur

Marque: Jensen

Modèle: Car Stereo System MPX6411

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Ce manuel convient également à

MPX6411

Instruction Manual

Manual de Instrucciones

Guide d'instructions

MPX6411

TABLE OF CONTENTS

Introduction ..............................................................................................1

Preparation ..............................................................................................2

Wiring .......................................................................................................3

Installation ................................................................................................4

Operation .................................................................................................6

Tuner Operation .......................................................................................9

Radio Operation ............................................................................10

CD Player Operation ..............................................................................11

MP3/WMA Operation .............................................................................12

CD Changer Operation ..........................................................................14

JPORT Operation ..................................................................................14

Remote Control ......................................................................................15

Care and Maintenance ...........................................................................15

Troubleshooting .....................................................................................16

Specifications .........................................................................................16

12-Month Limited Warranty ....................................................................17

CONTENIDO

Introducción ...........................................................................................19

Preparación ............................................................................................20

Cableado ................................................................................................21

Instalación ..............................................................................................22

Operación ..............................................................................................24

Operación de la Radio ...........................................................................27

Operation de la Radio XM

® ......................................................................................28

Operación del Reproductor de CD .........................................................29

Operación de MP3/WMA .......................................................................30

Operación del Cambiador de CD ...........................................................32

Operación del JPORT ............................................................................32

Control Remoto ......................................................................................33

Cuidado y Mantenimiento ......................................................................33

Corrección de Problemas ......................................................................34

Especificationes .....................................................................................34

Garantia Limitade de 12 Meses .............................................................35

TABLE DES MATIÈRES

Introduction ............................................................................................37

Préparation ............................................................................................38

Câblage .................................................................................................38

Installation ..............................................................................................40

Opération ...............................................................................................42

Fonctionnement de la radio ...................................................................45

Fonctionnement de la radio XM

® .......................................................................... 46

Fonctionnement du lecteur CD ..............................................................47

Fonctionnement de MP3/WMA ..............................................................48

Opération de changeur de CD ...............................................................50

Opération JPORT ..................................................................................50

Prêt à être télécommandé .....................................................................51

Soin et entretien .....................................................................................51

Dépannage ............................................................................................52

Specifications .........................................................................................52

Garantie limitée de 12 mois ...................................................................53

MPX6411

INTRODUCTION

Congratulations on your purchase of the Jensen MPX6411 Mobile Receiver. It’s a good idea to

read all of the instructions before beginning the installation. We recommend having your

Jensen MPX6411 installed by a reputable installation shop.

Features

XM READY

• Requires Terk XMD1000 Tuner Box (Sold Separately)

• Requires Terk XMDJEN100 or Jensen JXMC XM Cables (Sold Separately)

• Advanced display shows the artist and song title

• Direct Channel entry

• XM channel and category at a glance

MP3 / WMA

• MP3 / WMA- CD-R/RW compatible

•ID3 tag compatible

• MP3 / WMA quick file search via rotary volume knob

• MP3 / WMA song surfing

• MP3 / WMA file search by title, artist or folder

• MP3 / WMA direct track access

• Supports up to 32 characters for file or folder names

• MP3 / WMA “loaded/inserted” icon

• High-speed audible fast forward/rewind

• MP3 100-second ESP - Electronic Skip Protection

• WMA 200-second ESP - Electronic Skip Protection

• 16MB SDRAM buffer

• Last position memory

• Random/repeat/intro

• High-speed audible track search

• 1-Bit D/A converter

• Anti-shock mechanism

• 40-second ESP - Electronic Skip Protection

AM/FM Tuner

• World Tuner

• 30 station presets (18 FM/12AM)

• JENSEN Plus Tuner II

• Auto station store

• Preset scan

• One-touch memory

• Auto stereo/mono

• Manual local/distance

• Manual tuning up/down

• Auto seek tuning up/down

• 5-second Scan tuning

Chassis

• Motorized Swing-down detachable faceplate

• 1.0 DIN

• Import ISO/DIN mountable

• 20-pin power harness

General

• PTM - Personal Text Message

• Allows up to 32 character personal message

• User friendly setup menu

• LCD contrast control

• LCD dimmer control

•Clock

• Selectable display priority

• Switchable Bi-color illumination – Red or Blue

• Infrared remote control (included)

• IR30 steering wheel remote control ready (sold separately)

• High contrast positive Liquid Crystal Display (LCD)

• Electronic volume, bass, treble, balance, fader

• Rotary encoder audio control

• Programmable turn-on volume

• Multi-button power on

• Keyless CD eject

• 2-Pair Front / Rear pre-amp outputs

• 5V Peak / 2V RMS RCA pre-amp output voltages

• 200-ohm low impedance preamp output

• 1-Subwoofer pre-amp output (RCA) (adjustable level control)

• 200Hz low pass subwoofer crossover

• 1-Pair rear RCA auxiliary input

• Flex-Fader

• iEQ5 – instant EQ

• 5-selectable iEQ curves – Beat, Jazz, Classic, Pop and Rock

• iX-Bass – instant eXtended bass

•Mute

• Hard carry case

Optional Accessories

iAUX READY (Sold Separately)

• Can connect to any portable media device or multimedia device using a standard 3.5mm

plug

• Converts 3.5mm auxiliary input to RCA stereo outputs for easy connection to the radios

Aux inputs

JPORT READY (Sold Separately)

• Controls all iPod’s except “Shuffle” (audio only)

• CD changer pass-thru input

• Plug both the iPod and CD changer in at the same time (operates independently)

• APPLE® approved iPod interface cable (Included with jPort Adapter Module)

MPX6411

PREPARATION

Tools and Supplies

The following tools and supplies are needed to install the radio.

• Torx type, flathead and Philips screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screwdriver, socket wrench set or other tools)

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16-18 gauge speaker wire

SPEAKER REQUIREMENTS: Only connect speakers rated in the load impedance of 4

ohms. Speakers with a load impedance less than 4 ohms could damage the unit.

Pre-installation

1. Disconnect Battery

Before you begin, always disconnect the battery negative terminal.

2. Remove Transport Screws

3. Remove Radio from Sleeve

Lift latches on both sides of sleeve to remove half-sleeve from radio.

TRANSPORT

SCREWS

HALF

SLEEVE

MPX6411

WIRING

Wiring with a Wiring

Adapter (Purchased

Separately)

Connect Wires

You can make all these

connections without even being

in the vehicle.

1. Splice or crimp wires.

2. Attach wiring adapter to the

car wiring harness.

Wiring Diagram / Color Codes

1. Power Antenna (dark blue

wire) - Connect to the power

antenna or a amplifier. If not

used, tape the bare end of

wire.

2. Ground (black wire) -

Connect to the ground

terminal or a clean,

unpainted part of the

chassis.

3. Memory/Battery (yellow

wire) - Connect to the

battery or to a 12 volt power

source that is always alive.

The radio will not work if this

wire is not connected.

4. Accessory/Ignition (red wire)

- Connect to the existing

radio wire or radio fuse.

5. Left front speaker

6. Right front speaker

7. Left rear spearker

8. Right rear speaker

9. RCA Outputs to Amplifier

10. Auxiliary Input Cable

(yellow)

11. Antenna

12. XM

Direct Connect Cable

13. XM

Audio Input (black RCA)

14. Subwoofer Output (blue)

15. CD Changer/JPORT connector - Use this 8-pin DIN socket to connect an optional CD

Changer or JPORT (sold separately).

*TERK XMDJEN100 cables sold separately.

**TERK XMD1000 Direct Tuner and antenna sold separately.

NOTE: The amplifier in this radio is only designed for use with four speakers. Never

combine (bridge) outputs for use with two speakers. Never ground negative speaker

leads to chassis ground. Failure to wire exactly as shown may cause electrical damage

to the radio.

MPX6411

Fuses

When replacing a fuse, make sure the new fuse is the correct type and amperage. Using an

incorrect fuse could damage the radio. The MPX6411 uses one 15 amp fuse located below the

wiring connector (15 amp fast blow ATO).

Reconnect Battery

When wiring is complete, reconnect the battery negative terminal.

Technical Assistance

If you require assistance, contact Technical Support at 1-800-323-4815 from 8:30am to

7:00pm EST Monday through Friday and from 9:00am to 5:00pm EST on Saturday.

Connecting the Satellite Radio Receiver (optional)

Before you can listen to XM

satellite radio, you must install the XM

Direct Receiver and

antenna (purchased separately). The XM

Direct Receiver is the central data receiving

equipment required to process the satellite signals from the external antenna. It is typically

installed in the dash, under the seat, or in the trunk or rear of the vehicle. Do not mount the

Direct Receiver near a heater vent or where it can be exposed to extreme temperatures.

In addition, when running the wire for the external antenna do not kink or pinch the antenna

cable. A sharp 90 degree bend or slight "nick" to the outer cable sheath will cause signal

degradation. The wiring diagram on page 3 will help you identify the proper connections.

INSTALLATION

This unit is designed for installation in cars, trucks and vans with an existing radio opening. In

many cases, a special installation kit will be required to mount the radio to the dashboard.

These kits are available at electronics supply stores and car stereo specialty shops. Always

check the kit application before purchasing to make sure the kit works with your vehicle. If you

have trouble locating a kit or need installation assistance, contact Technical Support at 1-800-

323-4815 from 8:30am to 7:00pm EST Monday through Friday and from 9:00am to 5:00pm

EST on Saturday.

Universal Installation Using Mounting Sleeve

1. Remove the detachable front panel, if it is attached to the chassis, by pushing the

“Release” button.

2. Slide the mounting sleeve off of the chassis if it has not already been removed. If it is

locked into position, use the removal keys (supplied) to disengage it. The removal keys

are depicted on page 5.

3. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is

not large enough, carefully cut or file as necessary until the sleeve easily slides into the

opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that

there will be sufficient space behind the dashboard for the radio chassis.

4. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.

With the sleeve fully inserted into the dashboard opening, bend as many of the tabs

outward as necessary to firmly secure the sleeve to the dashboard.

MPX6411

5. Place the radio in front of the dashboard opening so the wiring can be brought through the

mounting sleeve.

6. Follow the wiring diagram carefully and make certain all connections are secure and

insulated with crimp connectors or electrical tape to ensure proper operation.

7. After completing the wiring connections, attach the front panel and turn the unit on to

confirm operation (vehicle ignition switch must be on). If the unit does not operate,

recheck all wiring until the problem is corrected. Once proper operation is achieved, turn

the ignition switch off and proceed with final mounting of the chassis.

8. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is

fully seated and the spring clips lock it into place.

9. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of

the chassis using the hex nut provided. Fasten the other end of the perforated strap to a

secure part of the dashboard either above or below the radio using the screw and hex nut

provided. Bend the strap, as necessary, to position it. CAUTION: The rear of the radio

must be supported with the strap to prevent damage to the dashboard from the weight of

the radio or improper operation due to vibration.

10. Re-attach the front panel to the chassis and test radio operation by referring to the

operating instructions for the unit.

NOTE: For proper operation of the CD player, the chassis must be mounted within 20° of

horizontal. Make sure the unit is mounted within this limitation.

Kit Installation

If your vehicle requires the use of an installation kit to mount this radio, follow the instructions

included with the installation kit to attach the radio to the mounting plate supplied with the kit.

1. Wire and test the radio as outlined in the Universal Installation instructions.

2. Install the radio/mounting plate assembly to the sub-dashboard according to the

instructions in the installation kit.

3. Attach the support strap to the radio and dashboard as described in the Universal

Installation instructions.

4. Replace the dashboard trim panel.

ISO Installation

This unit has threaded holes in the chassis side

panels which may be used with the original factory

mounting brackets of some vehicles to mount the

radio to the dashboard. Please consult with your

local car stereo shop for assistance on this type of

installation.

1. Remove the existing factory radio from the

dashboard or center console mounting. Save all

hardware and brackets as they will be used to

mount the new radio.

2. Carefully unsnap the plastic frame from the

front of the new radio chassis. Remove and discard the frame.

3. Remove the factory mounting brackets and hardware from the existing radio and attach

them to the new radio. Do not exceed M5 x 9 MM maximum screw size. Longer screws

may damage components inside the chassis.

4. Wire the new radio to the vehicle as outlined in the Universal Installation instructions.

5. Mount the new radio assembly to the dashboard or center console using the reverse

procedure of step 1.

Remove Radio

To remove the radio after installation, remove the

trim ring by lifting in the center and pulling it off

from either side. Insert the removal keys straight

back until they lock, and then pull the radio out. If

removal keys are inserted at an angle, they will

not lock properly to release the unit.

REMOVAL KEYS

MPX6411

OPERATION

Power

Press the power button (1) or any other button on the front of the radio (except Eject) to turn

the unit on. Press the power button again to turn the unit off.

Mode

Press MODE (2) to select a different mode of operation, as indicated on the display panel.

Available modes include tuner (F1, F2, F3, AM1, AM2), XM Radio, CDP and auxiliary (AUX).

CD mode appears in the menu only if a CD is present in the CD player.

Audio Mute

Press the mute button (3) to silence the audio volume. “Mute” flashes in the display. Press

mute again to restore volume to the previous setting.

Volume / Audio Control

To increase the volume, rotate the volume control (4) clockwise. To decrease the volume,

rotate the volume control counter-clockwise. When volume is adjusted, the volume level will be

shown on the display panel as a number ranging from “0” (lowest) to “46” (highest).

Press the volume control repeatedly to step through the following audio functions: volume

(VOL), bass (BAS), treble (TRB), balance (BAL), fader (FAD) and back to volume. The unit

automatically exits audio control mode after five seconds of inactivity.

Bass

To adjust the bass level from “-6” to “+6”, press the volume control until “BAS” appears in the

display. Rotate the control clockwise to increase or counter-clockwise to decrease the bass.

“0” represents a flat response.

Treble

To adjust the treble level from “-6” to “+6”, press the volume control until “TRB” appears in the

display. Rotate the control clockwise to increase or counter-clockwise to decrease the treble.

“0” represents a flat response.

Balance

To adjust the balance from “L12” (full left) to ”R12” (full right), press the volume control until

“BAL” appears in the display. Rotate the control clockwise or counter-clockwise to adjust the

balance between the left and right speakers. “C00” represents a center balance.

Fader

To adjust the fader from “F12” (full front) to “R12” (full rear), press the volume control and

rotate it clockwise or counter-clockwise to adjust the fader between the front and rear

speakers. “C00” represents a center fader level.

iX-Bass

Press iX-BASS (5) to activate the iX-BASS feature. When listening to music at low volume

levels, this feature will boost the bass and treble ranges to compensate for the characteristics

of human hearing. When this feature is activated, “iX-BASS On” will appear in the display.

Press iX-BASS again to select “iX-BASS Off”. The iXBS icon will appear and remain in the

display when the iX-BASS feature is activated.

Equalizer Selector

The equalizer function applies preset sound effects to the unit’s audio output signal. Press

IEQ5 (6) to step through the following equalizer options: “Pop”, “Jazz”, “Classic”, “Beat”,

“Rock”, and “Off”. The equalizer options appear in the display as they are accessed.

When the equalizer function is activated, the most recently selected bass/treble levels cannot

be adjusted. When the equalizer function is not active, the unit will return to the most recently

selected bass and treble levels.

Liquid Crystal Display (LCD)

The liquid crystal display (LCD) panel (8) displays the frequency, time and activated functions

of the unit, including a combination audio level/disc indicator, which appears as dual disc icons

with circular bar graphs depicting the audio signal. In addition, the display contains a receive

signal indicator that depicts the relative strength of the incoming broadcast frequency.

NOTE: LCD panels may take longer to respond when subjected to cold temperatures for

an extended period of time. In addition, the visibility of the numbers on the LCD may

decrease slightly. The LCD display will return to normal when the temperature increases

to a normal range.

VOL

BAS

TRB

BAL

FAD

MPX6411

Display Options

Press DISPLAY/MENU (7) to navigate through the following options:

• Tuner: FREQ > Spectrum > PTM Message

• CDP/MP-3/WMA: Elapsed Time > Spectrum > PTM Message

• XM mode: Category Name > Artist Name > Song Title > Spectrum > PTM Message >

Channel Name

Menu Operation

A second function of the DISPLAY / MENU button (7) is to access a menu of radio options.

Press DISPLAY / MENU for more than three seconds to access the menu. “Menu” will appear

in the display. Navigate the menu by pressing DISPLAY / MENU momentariiy to move forward

to the next option. The menu can also be navigated by using the UP TUNING (10) or DOWN

TUNING (11) button to move to the next or previous option. Once the desired option appears in

the display, adjust that option by rotating the volume control within five seconds.

The following options are adjusted through this menu feature:

Contrast

The contrast level of the display is set at “CONTRAST 05” by default. Rotate the volume

control to adjust the contrast level from “00” to “10”.

Dimmer

The dimmer feature of the display is set to “DIMMER High” by default. Rotate the volume

control to turn the dimmer to the low setting.

XM Scroll

This option determines whether or not the XM display text scrolls continuously across the

screen. The default setting is “OFF”. Select “ON” to make the display text scroll continuously.

When set to off, you can view the display information by continuously pressing the DISPLAY

button (7).

NOTE: The XM Scroll option only appears when an XM box is connected.

Clock Format

This option allows selection of a 12 hour or 24 hour clock format. “CLK FORMAT 12H” is the

default setting. Rotate the volume control to change to the 24 hour clock format.

Time Set

The time on the clock will be set to “12:00” as the default. Program the current time by rotating

the volume control clockwise to adjust the minutes and counter-clockwise to adjust the hours.

Local / Distance Selector

This feature is used to designate the strength of the signals at which the radio will stop during

automatic tuning. “Distant” is the default, allowing the radio to stop at a broader range of

signals. To set the unit to select only strong local stations during automatic tuning, rotate the

volume control to select “Local”. “LOC” appears in the display.

Frequency Spacing

This option allows the selection of the frequency spacing appropriate for your area. “AREA

U.S.A.” is the default setting. Rotate the volume control to select the “Latin”, “Europe” or “Oirt”

options.

Programmable Turn-on Volume

Use the “VOL PGM” option to select the default volume the radio will assume when first turned

on. To program a specific start-up volume level, rotate the volume control to select the desired

level.

Beep Tone

The beep tone feature allows the selection of an audible beep tone to be heard each time a

button is pressed on the face of the radio. “BEEP TONE On” is the default display. Rotate the

volume control to select the “BEEP TONE Off” option.

Illumination Color

The “COLOR” option allows selection between two colors for the backlight illumination of the

unit. “COLOR 1” is the default display and will illuminate the unit in blue backlight. Rotate the

volume control to select “COLOR 2”, which will illuminate the display in red backlight.

Selectable Clock Display

When the selectable clock display (CLK ON LCD) feature is activated, the clock and default

greeting note will appear in the display when the radio is turned off but still connected to the

ignition wire. “CLK ON LCD On” is the default display for this option. To select that the clock

and greeting not be displayed when the unit is powered off, rotate the volume control to select

“CLK ON LCD Off”.

Key Light On/Off

When the key light feature is activated (ON) the preset buttons and the rest of the front panel

function buttons remain lit when the unit is turned off, but the ignition key remains on. Turn the

volume control to select “Key Light Off” if you would prefer the buttons not remain illuminated

when the unit is off.

Personal Text Message

The personal text message (PTM) feature allows you to enter a personal message up to 20

characters (including spaces) using the letters A-Z, the numbers 0-9 and the symbols “_”, “+”,

“-” and “!”. Press in on the volume control to access this option from the menu, then rotate the

volume control to select the first character for your message. Once you have selected your first

MPX6411

character, press in on the volume control to move to the next space and select the next

character. To leave a blank space, press the volume control again.

Greeting Note

When the unit is powered on, one of three greetings is displayed based on the time of day:

“Good Morning”, “Good Afternoon” or “Good Evening”. When the unit is powered off with the

ignition on, the LCD scrolls through the following messages (if the selectable clock display

feature is activated): “Radio Off”, “Visit us at Jensen.com”, “Enjoy Driving and Have a Safe

Trip”.

Front Panel Release

The front panel release button (9) releases the mechanism that holds the front panel to the

chassis.

Detaching the Front Panel

To detach the front panel, first press the front panel release button to release the left side of the

panel. Next, grasp the released side and pull it off the chassis. After removing the front panel,

store it in the supplied carrying case to protect it from dirt and damage.

Re-attaching the Front Panel

To re-attach the front panel, make sure the electrical terminals on the back of the panel are

free of dust and dirt, as debris could cause intermittent operation or other malfunctions.

Position the right side of the panel in place so that it is correctly engaged, then lightly press the

left side of the panel until the mechanism locks it into place.

Reset Button

The reset button is located on the front of the chassis and can only be accessed with the front

panel removed. The reset circuitry protects the microprocessor circuitry. Since resetting the

unit will erase the time and preset memories, it should only be activated upon initial installation

after all wiring is complete or if there is a malfunction of any of the switches on the unit. In these

circumstances, pressing the reset button will clear the system and return the unit to normal

operation.

Theft Deterrent LED

A light-emitting diode (LED) is located on the chassis behind the front panel and will flash when

the panel is removed. The flashing light serves as a visual warning to the would-be thief that

the unit has been disabled by removal of the front panel.

REMOVE FRONT PANEL

MPX6411

TUNER OPERATION

The MPX6411 comes equipped with a World Tuner, allowing you to receive channels in USA,

EUROPE, LATIN, & OIRT (Russia). See “Frequency Spacing” on page 7 to learn how to

change the World Tuner options.

Select a Band

Press BAND (19) to change between three FM bands and two AM bands. Each band stores up

to six preset stations.

Tuning

Manual Tuning

Press the UP TUNING (10) or DOWN TUNING (11) button for more than three seconds to

enter manual tuning mode, then press the UP TUNING or DOWN TUNING buttons to move the

radio frequency number up or down one step.

Auto Seek Tuning

Press the UP TUNING (10) or DOWN TUNING (11) button for less than three seconds to move

to next station automatically.

Scan

Press SCAN (20) to scan through strong stations in the current band. The radio pauses for five

seconds at each strong station. Press SCAN again to listen to the current station.

Preset Stations

Six numbered preset buttons store and recall stations for each band.

Store a Station

Select a band (if needed), then select a station. Hold a preset button (12-17) for three seconds.

The preset number will appear in the display.

Recall a Station

Select a band (if needed). Press a preset button (12-17) to select the corresponding stored

station.

Automatically Store / Preset Scan

Automatically Store

Automatically select six strong stations and store them in the current band. Select a band (if

needed). Press AS/PS (21) for more than three seconds. The new stations replace any

stations already stored in that band.

Preset Scan

Scan stations stored in the current band. Select a band (if needed). Press AS/PS (21) for less

than three seconds. The unit will pause for ten seconds at each preset station. Press AS/PS

again to stop scanning when the desired station is reached.

Stereo

The unit will automatically pick up a stereo signal, when available. When in stereo mode, the

“ST” icon (18) appears in the display. When no stereo signal is available, the unit will

automatically revert to mono operation, and no icon will be displayed.

MPX6411

RADIO OPERATION

Listeners can subscribe to XM

Radio on the Web by visiting www.xmradio.com, or by

calling (800) 967-2346. Customers should have their Radio ID ready (see “Displaying the

Identification (ID) Code”). Customers can receive a limited number of free-to-air

channels without activation.

Accessing XM

Radio Mode

To switch to XM

Radio mode, press MODE (2) until “XM RADIO” appears on the display.

Displaying the Identification (ID) Code

Before you listen to XM

Radio, you must subscribe to the service using your radio’s

identification number. To display the radio ID, press the DOWN TUNING (|<<) button (11) to

access channel 000. The screen displays “RADIO ID” followed by an 8-figure ID number.

Selecting a Station

Press the UP TUNING (>>|) or DOWN TUNING (|<<) button (10 and 11) to change to another

station.

Preset Stations

Press BAND (19) to change between three XM

Radio bands. Each band stores up to six

preset stations. You can store and recall a total of 18 preset stations.

Store a Station

1. Select a band (if needed), then select a station.

2. Hold a preset button (12 – 17) for three seconds. The preset number appears in the

display.

Recall a Station

1. Select a band (if needed).

2. Press a preset button (12 – 17) to select the corresponding stored station.

Preset Scan

1. Press AS/PS (21) for < 3 seconds. The unit pauses for 5 seconds at each preset station

for all three bands (XM-1, XM-2, and XM-3).

2. Press AS/PS again to stop scanning when the desired station is reached.

Tuner Modes

Press DISPLAY (7) to change the tuner mode to the following options in the order listed.

• Channel Name

• Genre (News, Sports, Hits, Kids, etc.)

• Artist name

• Song Name

• 11 Bar Spectrum Indicator

• PTM (Animated Message)

Display Information

If the selected channel name, artist, or title exceeds eight characters, the display information

will scroll twice upon selection.

Category Mode

To select stations in a specific category, perform the following steps.

1. Press and hold the BAND button (19) until “Direct-T” appears.

2. Press BAND again to display “CATEGORY”.

3. Turn the rotary encoder to move through the available categories.

4. Press the AS/PS button (21) to select the displayed category.

5. Once a category is selected, press the UP TUNING (>>|) or DOWN TUNING (|<<) button

(10 and 11) to select stations in the current category.

To change the category while in category mode, press the AS/PS button. “CATEGORY” will

flash in the display, allowing you to use the 5 and 6 buttons to select a different category.

Direct Tuning Mode

To enter a station directly, perform the following steps.

1. Press and hold the BAND button (19) until “Direct-T” appears.

2. Turn the rotary encoder to display XM CH 0 _ _.

3. Turn the rotary encoder again to select the first digit of the desired channel (0, 1, or 2).

4. Press the ENTER button (rotary encoder) to enter the first number and move to the

second position.

5. Turn the rotary encoder again to select the second digit of the desired channel (0 - 9).

6. Press the ENTER button (rotary encoder) to enter the second number and move to the

third position.

NOTE: Use the UP TUNING (>>|) or DOWN TUNING (|<<) button (10 and 11) to move

between the first and third positions.

7. Turn the rotary encoder again to select the third digit of the channel you want to tune to (0

- 9).

8. Press the ENTER button (rotary encoder) to enter the third number and access the

channel.

NOTE: If the channel is unauthorized or invalid, “CH Unavail” appears on the LCD and

return to the input interface after 2 seconds.

MPX6411

CD PLAYER OPERATION

Insert and Eject CD

Press the eject button (22) and let the motorized front panel swing-down to display the CD slot.

Insert a CD label side up. After inserting a CD, the front panel will close automatically. To stop

CD play and eject the CD, press the eject button. After ejecting the CD, the unit will close

automatically after 10 seconds or you can close the front panel immediately by pressing the

eject button again.

NOTE: The unit is designed for play of standard 5” (12 cm.) compact discs only. Do not

attempt to use 3” (8 cm.) CD singles in this unit, either with or without an adaptor, as

damage to the player and/or the disc may occur. Such damage will not be covered by

the warranty on this product.

Pause

Press the pause button (12) to suspend disc play. Press the pause button again to resume disc

play.

Track Select

Press the UP TUNING (10) or DOWN TUNING (11) button for less than one second to

advance to the next track on the CD. The selected track number will appear on the display.

Press and hold the UP TUNING (10) or DOWN TUNING (11) button for more than one second

to fast forward or fast reverse through the disc. CD play starts when the button is released.

Intro Scan (SCN)

During disc play, press SCN (13) to play the first 10 seconds of each track on the disc. When

the desired track is reached, press SCN again to end the scan and play the selected track.

Repeat (RPT)

Press RPT (14) during disc play to continuously repeat the track. Press RPT again to stop

repeating.

Random (RDM)

Press RDM (15) during disc play to play all tracks on a CD in random, shuffled order. Press

RDM again to stop random play.

Display CD Text

Press AS/PS (21) to display any text encoded on the CD (song title, artist, etc.).

CD Player Error Codes

If a problem should develop while operating the CD player, an error code (ER-1, ER-2, etc.)

may appear on the display panel. This can indicate a number of problems with the unit,

including a mechanical error or an error in the microprocessor control of the player. If an error

code should appear, try ejecting and reloading the disc into the player. While the disc is out of

the unit, make sure it is clean and undamaged, and then load it correctly. If this does not solve

the problem, pressing the reset button may help, but will erase the time and preset memory. If

the suggested measures do not solve the problem, contact an approved warranty station near

you for further assistance.

MPX6411

MP3/WMA OPERATION

MP3 and WMA (Windows Media Audio) music files are digital audio files that are compressed

to allow more files on a single CD. This unit can play MP3/WMA directly from files contained on

a CD-R/RW using the buttons on the receiver (or optional remote) as described below. Many

types of software are available for converting audio files into MP3/WMA formats. Jensen

recommends Nero, MusicMatch Jukebox or Roxio Easy CD Creator. Depending on the media

type and recording method, some CD-R/RW's may be incompatible with this unit. The unit

supports playback of MP3/WMA and CDDA (CDA), Mixed-Mode CDs and CD-Extra (including

multi-session discs), but discs on which the session has not been closed will not play.

Notes on MP3/WMA Play

This unit can play MP3 (MPEG1, 2, 2.5 Audio Layer 3). However, the MP3 recording media

and accepted formats are limited. When writing MP3/WMA, pay attention to the following

restrictions.

Acceptable Media

The MP3/WMA recording media acceptable to this unit are CD-ROM, CD-R and CD-RW.

When using CD-RW, use full format rather than quick format to prevent malfunction.

Acceptable Medium Formats

The following formats are available for the media used in this unit. The maximum number of

characters used for file name including the delimiter (".") and three-character extension are

indicated in parentheses.

• ISO 9660 Level 1 (11 characters)

• ISO 9660 Level 2 (31 characters)

• Joliet (31 characters)

• Romeo (31 characters)

Up to 200 characters can be displayed in the long file name format. For a list of available

characters, see the instruction manual of the writing software and the section “Entering File

and Folder Names” below. The media reproducible on this unit has the following limitations:

• Maximum number of nested folders: 8

• Maximum number of files per disc: 999

• Maximum number of folders per disc: 255

MP3/WMA written in formats other than those listed above will not play successfully and their

file names or folder names will not be display properly.

MP3/WMA Encoder and CD Writer Settings

Use the following settings when compressing audio data in MP3 data with the MP3 encoder.

• Transfer bit rate : 8 - 320 kbps

• Sampling frequency : 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz

When using a CD writer to record MP3/WMA up to the maximum disc capacity, disable

additional writing. To record an empty disc up to the maximum capacity at once, select the

“disc at once” option.

Entering ID3 Tag

This unit supports ID3 tag versions 1.0 and 1.1.

For the character codes, refer to the table to the

right. The unit also supports CD-TEXT encoded

discs for Album, Track and Artist Title

information.

Entering File and Folder Names

Names using the code list characters are the only

file names and folder names that can be entered

and displayed. Using any other character will

cause the file and folder names to be displayed

incorrectly. The unit recognizes and plays only

files with the MP3/WMA extension.

NOTE: A file name entered with characters not on the code list may not play correctly.

Writing Files into a Medium

When a medium containing MP3/WMA data is loaded, the unit checks all data. If the medium

contains many folders or non-MP3/WMA files, MP3/WMA play will be delayed, it may take time

for the unit to move to the next file, and searches may not be performed smoothly. Loading

such a medium may produce loud noise and cause damage to the speakers. Do not attempt

to play a medium containing a non-MP3/WMA file with the MP3/WMA extension or a

medium containing non MP3/WMA files.

Electronic Shock Protection

• 40 seconds for CDDA (CDA)

• 120 seconds for MP3 recorded at 44.1kHz, 128kbps

• 200 seconds for WMA recorded at 44.1kHz, 128kbps

Bit Rates

The unit supports bit rates from 32 - 320 kbps.

MP3 Playing Order

When selected for play, files and folders (Folder Search, File Search or Folder Select) are

accessed in the order they were written by the CD writer. As a result, the order in which they

are expected to be played may not match the order in which they are actually played. You may

be able to set the order in which MP3/WMA are to be played by writing them onto a medium

such as a CD-R with their file names beginning with play sequence numbers such as "01" to

"99".

MPX6411

For example, a medium with the following folder/file hierarchy is subject to Folder Search, File

Search or Folder Select as shown below.

Languages

The unit supports playback of the following seven languages: English, French, German,

Portuguese, Spanish, Italian and Dutch.

Loading an MP3/WMA Disc

Press the eject button (22) to lower the front panel, then Insert an MP3/WMA disc. After the

disc is loaded, the track number and elapsed time will appear, then the display will scroll

through any ID3 Tag information while the file is playing.

Pause

Press the pause button (12) to suspend disc play. Press the pause button again to resume disc

play.

Accessing the ID3 Tag

Press AS/PS (21) repeatedly during MP3/WMA play to access the ID3 information manually.

The display will show any of the following information that is programmed on the disc: Folder

Name, File Name, Album Title, Track Title, Artist Title.

Track Select

Press the UP TUNING (10) or DOWN TUNING (11) button for less than one second to

advance to the next track on the disc, or for more than one second to fast forward or fast

reverse through the disc. Disc play starts when the button is released.

Navigating Folders

Press the Folder Down (16) button (also the “5” button) to skip to the next folder, or press the

Folder Up (17) button (also the “6” button) to return to the previous folder.

Intro Scan (SCN)

During disc play, press SCN (13) to play the first 10 seconds of each track on the disc. When

the desired track is reached, press SCN again to end the scan and play the selected track.

Press SCN for more than three seconds to play the first 10 seconds of each track in the current

folder. When the desired track is reached, press SCN again for more than three seconds to

end the scan and play the selected track.

Repeat (RPT)

Press RPT (14) to repeatedly play the current file. Press RPT again to resume normal play.

Press RPT for more than three seconds to repeatedly play all files in the current folder. Press

RPT again for more than three seconds to resume normal play.

Random (RDM)

Press RDM (15) to randomly play all files on the disc. Press RDM again to resume normal play.

Press RDM for more than three seconds to randomly play all files in the current folder. Press

RDM again for more than three seconds to resume normal play.

MP3/WMA File or Folder Search

The unit offers three methods of searching for files or folders on a disc:

Direct File Number Search

Press BAND (19). The LCD will display "Number", and the illumination around the select knob

(4) will blink. Rotate the knob to select the desired track number, then press in on the knob to

confirm and play the selected file.

Navigation Search

Press BAND (19) twice. The LCD will display "Navigate", and the illumination around the select

knob (4) will blink. Rotate the knob to navigate through all folders and sub-folders on the disc.

The folder names will be displayed on the LCD. Press the select knob for more than three

seconds to play the first file in the folder. Press the select knob for less than three seconds to

access the sub-folders or files. Rotate the select knob to navigate, then press the select knob

to confirm and begin file play. During navigation search, press AS/PS or rotate the select knob

counter-clockwise to move back to the last upper level of a folder.

Direct Alphabet Search

Press BAND (19) three times. The LCD will display "Alphabet", and the illumination around the

select knob (4) will blink. Rotate the select knob to choose a character, including letters A-Z,

numbers 0-9 and the symbols “_”, “-”, “+” and “!”. Press the select knob to confirm entry and

move to the next character space. The unit will also search for matching file or folder names

when only the first few characters are entered. Rotate the select knob to navigate the files or

folders, then press the select knob to confirm and play file.

MPX6411

CD CHANGER OPERATION

Please call Jensen technical support at 1-800-323-4815 for a complete list of CD changers

compatible with this unit. The following Jensen CD Changers are compatible with this unit:

JCH10RF and CH1001.

After the CD changer has been installed and properly connected, press the Reset button to

initialize the installation. Refer to the owner’s manual included with the CD changer for

instructions on installing, loading and using the CD magazine.

CD Changer Mode

Press MODE (2) during radio or disc play to select operation of the CD changer. “CDC” will

appear in the display. Disc play will begin, and the disc and track numbers will be shown in the

display. If a new magazine has been loaded into the changer, play will begin from the first track

of the first disc. If a magazine was already in the changer, play will resume where it ended.

Disc Select (UP/DN)

To select a disc for play, use the UP (17) button to advance to a higher disc or the DN (16) button to move

back to a lower disc. The number of the disc in play appears on the display.

Other Features

The Play/Pause, Scan, Repeat, Shuffle, Track Select and Fast Forward/Fast Reverse features

for CD changer play are accessed in the same methods as for regular disc play. Refer to the

CD Player Operation section of this manual for details.

CD Changer Error Codes

If problems arise during CD changer operation, the following error codes may appear in the

display:

ER-1: No magazine loaded in the CD changer. ER-2: Problem in the disc loading function.

ER-3: Error in the disc loading function. ER-4: Error in the disc unloading function.

ER-5: Error in the magazine position. ER-6: Error in the laser pickup position.

ER-7: Error in the laser focus on the disc.

To resolve any of the above problems, eject the magazine from the changer and verify that the

discs are clean, undamaged and loaded correctly. Pressing the reset button may help, but will

erase the time and preset memories. If the suggested measures do not solve the problem,

contact an approved warranty station near you for further assistance.

JPORT OPERATION

After the JPORT has been installed and connected, press the RESET button to initialize the

installation. The JPORT can be used to control your iPod and an optional CD Changer. Refer

to the owner’s manual included with the JPORT for instructions regarding the operation

of external devices attached to your JPORT.

MPX6411

REMOTE CONTROL

The remote control will allow you to control the basic functions of the MPX6411.

The remote control sensor is at the top left of the IX-BASS (18) button.

CARE AND MAINTENANCE

CD Player

The following guidelines will help you extend the life of your CD player:

1. When cleaning the vehicle interior, do not get water or cleaning fluids on the unit.

2. The CD player will not operate properly in extreme hot/cold or under damp conditions. In

case of such conditions, wait until the vehicle interior reaches a normal temperature or

any condensation on the disc player lens has evaporated before using the player.

3. Never insert anything other than round 5” CDs into the player. Attempting to insert CDs of

other sizes (even with an adaptor) will cause damage not covered by the warranty.

4. Always remove the CD when the player is not is use.

5. The unit is designed with a vibration dampening CD mechanism to minimize interruption

of disc play due to normal vibration in a moving vehicle. However, occasional sound skips

may occur when driving on very rough roads. This will not scratch or damage the disc,

and normal play will resume when the rough conditions cease.

Compact Discs

CD-R and CD-RW Capability

Depending on media type and method of "recording/burning", some CD-R/RWs may be

incompatible with this unit. After "recording/burning", the session must be closed. Please refer

to your software's recommended procedures for closing a disc/session. Review your recording

software to familiarize yourself with the correct "recording/burning" procedures. We

recommend using the latest versions of ROXIO

or NERO

burning software.

In addition, this unit will only recognize the CDDA (Compact Disc Digital Audio), .MP3 and

.WMA formats "recorded / burned" onto a CD-R/RW. This unit does not support .WAV, .OGG

or other formats.

CD Care and Handling

Dirt, dust, scratches and warpage can cause skips in the playback and deterioration of sound

quality. Please follow these guidelines to take care of your compact discs.

1. Carefully wipe fingerprints, dust and dirt from the disc’s playing surface with a soft cloth.

Wipe in a straight motion from the inside to the outside of the disc.

2. Never use chemicals such as record sprays or household cleaners to clean CDs, as they

can irreparably damage the disc’s surface.

3. Discs should be kept in their storage cases when not in use.

4. Do not expose discs to direct sunlight, high temperatures or high humidity for long

periods.

5. Do not stick paper, tape or labels on disc surfaces.

MPX6411

TROUBLESHOOTING SPECIFICATIONS

CEA Power Ratings

Power Output . . . . . . . . . . . . . . . .16 watts RMS X 4 channels into 4-ohms @ < 1% THD+N

Signal to Noise Ratio. . . . . . . . . . . . . . 90dBA below reference. (Reference: 1 watt, 4-ohms)

Dynamic Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Watts @ 4-Ohms all channels driven

Frequency Response . . . . .20Hz to 20kHz (-3dB), Auxiliary input used as source reference

Reference Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14.4VDC

CD Player

Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>90dBA

Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz to 20kHz, -3dB

Channel Separation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 55dB @ 1kHz

D/A converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-Bit/Ch

FM Tuner

Tuning Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5MHz - 107.9MHz

Mono Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12dBf

50dB Stereo Quieting Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16dBf

Stereo Separation @ 1kHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>30dB

Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Hz to 14kHz, -3dB

AM Tuner

Tuning Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530kHz - 1720kHz

Sensitivity @ 20dB Signal to Noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30uV

Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Hz - 2kHz, -3dB

Auxiliary Input

Input Sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . .400mV RMS for 1 watt RMS into 4-ohms

Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Hz to 20kHz, -3dB

Input Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10k-ohms

General

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 to 16VDC, negative ground

Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 amp, ATO type

Wire Harness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-pin quick-disconnect

DIN chassis dimensions . . . . . . . . . . . . . . . . . . . . . 2” X 7" X 7" (51mm x 178mm x 178mm)

Specifications subject to change without notice.

Problem Cause Corrective Action

Does not operate

(display does not

light)

No power to yellow wire;

no power to red wire

Check connection with test light;

check vehicle fuse with test light.

Inline fuse blown Replace fuse.

No power to unit Inline fuse blown Check/replace fuse.

No speakers oper-

ate (display lights

normally)

Speaker harness not con-

nected

Connect speaker harness; check

speaker wires.

Not all speakers

operate

Incorrect splices or con-

nections

Check all splices and connec-

tions.

Speaker wires shorting to

chassis ground or to each

other

Check splices, insulate all bare

wires.

Blows fuses Power wire shorting to

ground

Make sure wire is not pinched.

Speaker wires shorting to

ground

Make sure wire is not pinched.

Incorrect fuse/fuse too

small

Install fuse of correct rating.

CD skips too much Receiver mount is not

solid or backstrap is not

secure

Check mounting and backstrap,

tighten if needed.

La page charge ...

Jensen Car Stereo System MPX6411 Manuel utilisateur

Marque: Jensen

Modèle: Car Stereo System MPX6411

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Jensen Car Stereo System MPX6411 User manual
español: Jensen Car Stereo System MPX6411 Manual de usuario

Jensen Car Stereo System MPX6411 Manuel utilisateur

Ce manuel convient également à

Jensen Car Stereo System MPX6411 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents