Krups AUTOMATIC XP52 Series Manuel utilisateur

Marque: Krups

Modèle: AUTOMATIC XP52 Series

Catégorie: Cafetières

Taper: Manuel utilisateur

Ce manuel convient également à

www.krups.com

NC00026257-01

English . . . . . . . . . . . . . . . . . . p. 1

Français . . . . . . . . . . . . . . . . . p. 17

Español . . . . . . . . . . . . . . . . . p. 33

Réalisation : Espace Graphique

WWW.KRUPS.COM

XP52 AUTOMATIC

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:03 PageC1

fig. 6

fig. 1 fig. 2

fig. 5

fig. 11

fig. 3

fig. 4

ig. 4fig. 4

fig. 8

fig. 9

fig. 12

fig. 10

fig. 7

fig. 16.2

fig. 18.1 fig. 18.2

fig. 17

fig. 20

fig. 19

fig. 14

fig. 13

fig. 15

fig.21

fig. 16.3

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:03 PageC4

fig. 22

fig. 24fig. 23

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 PageC7

Filter-holder position for 1 cup

Position du porte-filtre pour 1 tasse

Posición del portafiltro para 1 taza

Filter-holder position for 2 cups

Position du porte-filtre pour 2 tasses

Posición del portafiltro para 2 tazas

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 PageC9

English

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to

reduce the risk of fire, electric shock, and/or injury to persons including the following :

1. Read all instructions prior to first use.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against fire, electric shock and injury to persons, do not immerse cord,

plugs or machine in water or other liquid.

4. Not intented for use by children.

5. Close supervision is necessary when any machine is used near children. Keep

machine out of reach of children.

6. This appliance is not designed to be used by people (including children) with a

physical, sensory or mental impairment, or people without knowledge or experience,

unless they are supervised or given prior instructions concerning the use of the

appliance by someone responsible for their safety.

7. Children must be supervised to ensure that they do not play with the appliance.

8. Burns can occur from touching hot plate, hot water or steam. Exercise caution.

9. Exercise caution when using the steam nozzle as steam can cause scalding.

10. Unplug machine from outlet when not in use and when cleaning. Allow to cool before

putting on or taking off parts, before cleaning the machine, and before storing.

11. All machines are subject to stringent quality control. Practical tests using machines

taken at random are conducted and this may explain any slight marks or coffee

residue prior to use.

12. Do not operate any machine with a damaged cord or plug or after the machine

malfunctions, or has been damaged in any manner. Return machine to the nearest

Krups Service Center for examination, repair or adjustment or your respective

countries Consumer Service Department.

13. To reduce the risk of injury do not drape cord over the counter top or table top where

it can be pulled on by children or tripped over accidentally.

14. Do not let cord hang over edge of table or counter, or touch hot surfaces.

15. The use of accessory attachments not recommended by Krups may result in fire,

electric shock or injury to persons.

16. Do not use outdoors.

17. Do not place on or near a hot gas or electric burner, or in a heated oven.

18. To disconnect the machine, turn the control to “off” then remove plug from wall outlet.

Do not yank cord, instead grasp plug and pull to disconnect.

19. Do not use the machine for other than intended use.

20. Do not pour liquids other than water and descaling solutions specified in this manual

into the water tank.

21. Protect the machine against humidity and freezing.

22. This machine is for household use only.

SAVE THESE INSTRUCTIONS

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page1

English

CAUTION

This machine is intended for household use only. Any servicing other than cleaning and

user maintenance should be performed by the nearest authorized Krups Service Center.

Visit our website at www.krupsusa.com in the USA or www.krups.ca in Canada or

contact your respective country's Consumer Service department for the service center

nearest to you.

To reduce the risk of fire or electric shock, do not attempt to disassemble the machine.

Repair should be done by an authorized Krups Service Center only.

SHORT CORD INSTRUCTIONS

A.We do not recommend using an extension cord with this device.

B.If an extension cord is absolutely necessary,

1) the marked electrical rating of the extension cord should be at least as great

as the electrical rating of the machine,

2) the longer cord should be arranged so that it will not drape over the counter

top or table top where it can be pulled on by children or tripped over.

C.This machine has a polarized plug (one blade is wider than the other). To reduce

the risk of electric shock, this plug is intended to fit into a polarized outlet only

one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician. Do not attempt to modify the plug in any

way.

In the interest of improving products, Krups reserves the right to change specifications

without prior notice.

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page2

1. DESCRIPTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 4

2. TECHNICAL INFORMATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 4

3. TIPS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 4

4. USING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 5

5. MAKING AN ESPRESSO

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 6

6. STEAM FUNCTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 7

7. CLEANING AND MAINTENANCE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 9

8. DESCALING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 10

9. PROBLEMS, PROBABLE CAUSES AND CORRECTIVE ACTIONS

. . . . . . . p. 11

10. DISPOSING OF YOUR MACHINE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 13

KRUPS MANUFACTURER's WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .p. 14

English

TABLE OF CONTENTS

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page3

English

a Water tank lid

b Removable water tank

c Measuring spoon

d Cup tray

e Control panel

e1. On/off button

e2. 1 cup button

e3. 2 cups button

e4. Steam preheating position

f Steam production knob

g Brewing head

h Filter holder with grounds or pod ejection

system and gradual coffee tamping system:

KPT "Krups Precise Tamp": Compatible with

ground coffee (1 or 2 cups) and ESE or soft

pods

i Drip tray grid

j Drip tray with overflow indicator

k Steam nozzle

l Auto-cappuccino accessory

1. DESCRIPTION

Your Krups espresso machine is equipped with a filter-holder that has three patented systems designed

to help you make the perfect espresso at home.

1. KRUPS Precise Tamp: gradual tamping of the espresso ground coffee as the filter-holder is turned

ensures that coffee is tamped precisely each time.

2. Coffee ejection system under the filter-holder for clean removal of the cake each time.

3. The filter-holder is compatible with all types of pods including E.S.E. and soft pods.

The filter-holder is also removable and can be frequently cleaned to maintain the filter-holder system in

perfect working order. For your safety, the filter-holder is equipped with a locking system when pressure

rises.

n Pump: 15 bars

n Filter-holder with grounds or pod ejection system. Compatible with espresso ground coffee and all

types of pods including E.S.E. and soft pods.

n Steam function

n Automatic shutoff.

n Removable water tank (capacity: 1.1 litres).

n Power: 1450 W

n Voltage: 120V – 60Hz

n Anti overheating safety mechanisms

n Dimensions: 11-3/4” x 9” x 11” (h x l x d)

IMPORTANT!

Operating voltage: This device is designed to work only at alternating current 120V.

Type of use: This machine is designed EXCLUSIVELY for household use only. Any

non-residential use including commercial purposes will void the warranty.

n For an espresso with intense flavor, we recommend using freshly ground espresso coffee which is ideal for

the delicacy of this type of coffee, along with cup capacity that does not exceed 50 ml.

n Keep the espresso ground coffee in the refrigerator, in an air-tight container as it retains its flavor longer.

n Do not fill your filter holder to the brim, but use the measuring spoon (1 cup = 1 spoon and 2 cups =

2 spoons).

n If you do not use the appliance for more than 5 days, rinse and drain the water tank.

2. TECHNICAL INFORMATION

3. TIPS

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page4

English

n Before removing the water tank to fill or empty it, always turn the appliance off.

n Always place the unit on a flat, stable, heat-resistant work surface.

n To obtain an espresso at exactly the right temperature, we recommend that you preheat your cups.

n To prolong the life of your appliance, we recommend you always use a Claris Aqua Filter System cartridge

(reference: F088) and that you descale the appliance at regular intervals

IMPORTANT!

Before using for the first time, after a prolonged period of inactivity or after

descaling, the machine must be cleaned as described in paragraph 4: “USING”.

Before using your espresso machine for the first time, clean all accessories using warm water and a gentle

dishwashing liquid, and rinse well before replacing.

Make sure the steam knob on the right of the appliance is in the 0 position.

If you are not using the Claris cartridge, please refer to the paragraph below “RINSING OF

YOUR APPLIANCE”.

A. INSTALLING THE CLARIS CARTRIDGE (to be done every time the cartridge is replaced)

n Screw the Claris filter into the bottom of the water tank.

n Fill the water tank with water and replace it (fig.2 and 3).

n Place a container under the steam nozzle.

n Turn the machine on by pressing the "On / Off" button (fig.4).

n As soon as the machine reaches the required temperature, the "on/off" button stops flashing and the

1 cup and 2 cups buttons light up.

n Turn the knob to the “steam” position (fig. 13).

n At the beginning, steam comes out of the steam nozzle and the four buttons flash.

n Turn the knob to the “0” position (fig. 15). The machine automatically starts 2 or 3 cycles of intermittent

pumping.

n The four buttons begin to flash again.

n Turn the knob to the “steam” position: water comes out of the steam nozzle. If water does not flow from

the nozzle, repeat the operation from the beginning.

n Turn the knob to the “0” position (fig. 15).

n In this manner you can be sure that water is circulating through the filter cartridge.

IMPORTANT:

This installation procedure must be carried out every time the cartridge is

replaced.

The Claris cartridge needs to be replaced every 2 to 3 months if it is used daily.

B. RINSING YOUR APPLIANCE (to be done before the first use and after each cleaning /

descaling operation)

- RINSING OUT THE ESPRESSO CIRCUIT

n Turn the machine on and fill the water tank (fig. 1, 2, 3 and 4).

n Insert the filter holder (without espresso ground coffee) in the appliance (fig.7).

n Place a container of sufficient volume under the filter holder.

n As soon as the appliance reaches the right temperature, the “on/off” light will stop blinking and the “1

cup” and “2 cup” buttons will light up.

4. USING

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page5

English

n Press the “2 cups” button and let the water run out into a container (fig.9). Repeat this operation 5

times.

n If necessary, stop the operation by pressing the "2 cups" button (fig.9) to empty the container and

resume the operation.

n Empty the container and unlock the filter holder: press the "OPEN" button on the filter holder and turn

it to the left (fig.10).

RINSING OUT THE STEAM CIRCUIT.

Before using the steam function for the first time, the steam circuit should be cleaned.

n Fill the water tank

n Turn the appliance on by pressing the button.

n Place a recipient underneath the steam nozzle.

n Press the button, it starts to flash.

n When the button has stopped flashing, turn the steam switch to position and let the water run until

steam is formed.

n Keep the steam production going for at least 30 seconds.

In order to extract the maximum flavor from the beans, this machine pre-infuses each cup. The pump works

for 3 seconds, pauses for 3 seconds, and then continues until the cup is finished.

PREHEATING THE ACCESSORIES

For the best results, we recommend that you preheat the accessories (filter holder and cups) without

espresso ground coffee. To do so:

n Fill the water tank and turn the machine on. (fig.1, 2, 3 and 4).

n Put the filter holder in place, place the cups below.

As soon as the appliance reaches the required temperature, the "on/off" light stops flashing and the "1

cup" and "2 cups" buttons light up.

n Then press the "1 cup" or "2 cups" button (fig. 8 or 9).

n Once the cup or cups are filled with hot water, remove them.

n Unlock the filter holder: press "OPEN" while turning the filter holder to the left and remove it from the

machine. (fig.10).

WITH GROUND COFFEE

The type of coffee you choose will determine the strength and taste of your espresso. Always

use espresso ground coffee. Do not use instant coffee, cafetiere coffee or filter coffee.

n Fill the water tank and turn the machine on (fig. 1, 2, 3 and 4). During the preheating of the appliance,

the light flashes.

n Using the measuring spoon, place the espresso ground coffee in the filter holder: one spoon (full to the

brim) per cup (fig.5).

n Remove any excess espresso ground coffee from the edge of the filter.

Important: Do not tamp the coffee down in the filter holder. The coffee is automatically

tamped using the KTS “Krups Tamping System”.

n Insert the filter holder in the device by turning it to the right as far as it will go, up to the stop

(fig.7).

n Put one or two cups under the filter holder.

As soon as the appliance reaches the required temperature, the "on/off" light stops flashing and the "1

cup" and "2 cups" buttons light up.

n Then press the "1 cup" or "2 cups" button (fig. 8 or 9).

5. MAKING AN ESPRESSO

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page6

English

n Once the cup or cups are filled, unlock the filter holder press “OPEN” while turning the filter holder to

the left and remove it from the machine (fig. 10).

n Remove the used espresso coffee grounds using the ejection system by pressing the "EJECT" button

located between the two coffee outlet nozzles (fig.11). Wash the filter under running water, pressing

"EJECT" to eliminate the remnants of grounds.

The filter holder can now be filled again to prepare other espressos.

Note: It is always possible to stop the coffee flowing by pressing the "1 cup" or "2 cups" button again.

IMPORTANT: If you want a strong or light espresso, vary the amount of coffee or water (a full

spoon for a strong espresso and a less full spoon for a light espresso). But in both cases, be

sure to tighten your filter holder as much as possible.

WITH AN “E.S.E." ESPRESSO POD

“ESE” for “Easy Serving Espresso" is a packaged pod (44 mm diameter) of 7g of selected

coffee, ground and compacted between two paper filters, specially designed to make Italian

style ristretto (tight) espressos.

This system allows for simple and clean use of your machine.

n Fill the water tank and turn the machine on (fig. 1, 2, 3 and 4). During the pre-heating phase, the

indicator light will flash.

n If necessary, tear the excess pre-cut paper off the pod, put the E.S.E. pod in the filter holder, with the

red writing facing down, if any (fig.6).

n Be sure to place all the paper inside the filter holder, otherwise there might be leaks.

n If the pod is not positioned correctly, the result in the cup will not be satisfactory.

n Never use two pods together.

n Then, follow steps of pictures 7 to 11 for preparing an espresso.

n NB: Once you have obtained the sufficient amount of coffee, you can stop the flow at any time by

pressing the "1 cup" button (fig.8).

WITH A SOFT POD

Your machine is also compatible with soft pods, which are usually smaller in diameter than

E.S.E. pods. However since soft pods are not specifically designed for use with espresso

machines, you will get a less flavorful espresso than with an E.S.E. pod.

n Fill the water tank and turn the machine on (fig. 1, 2, 3 and 4). During the pre-heating phase, the

indicator light will flash.

n Place a soft pod in the filter holder. Never use two pods together.

n Be sure to place all the paper inside the filter holder, otherwise there might be leaks. If the pod

is not positioned correctly, the result in the cup will not be satisfactory.

n Then, follow steps of pictures 7 to 11.

NB: Once you have obtained the sufficient amount of coffee, you can stop the flow at any time by pressing

the "1 cup" button (fig.8).

INDIVIDUAL PROGRAMMING OF THE VOLUME OF WATER DISPENSED

To change the pre-programmed amount of water (50 ml per cup is the factory setting), proceed as follows:

n Fill the water tank and turn the machine on (fig. 1, 2, 3 and 4).

n Put a spoonful of coffee in the filter by using a measuring spoon or use an E.S.E. or soft pod.

n Put the filter holder in place and lock it by turning it to the right as far as it will go, up to the stop (fig. 7).

n Place a cup under the filter holder.

n Hold down the "1 cup" button (> 3 sec) until the "1 cup" light flashes quickly. The coffee flows out.

n When the desired amount of espresso is obtained, press the "1 cup" button. This amount will be saved

automatically.

n The next time when you press the "1 cup" button, you will obtain the most recently recorded amount.

Programming for 2 cups uses the same method, by pressing the "2 cups" button (> 3 sec).

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page7

English

Steam is used to foam milk (for example to make a cappuccino or a cafe latte).

To produce steam, the pump works by emitting an intermittent noise.

After using the steam function, the appliance cools automatically by pumping cold water through

the heating system. During the pumping cycles, the excess steam in the heating system is released with

the hot water into the drip tray. The steam and noise that accompany this phase are important for

cooling the appliance.

Warning: during and after using the appliance, the metal parts of the steam nozzle can become very hot.

USING THE STEAM NOZZLE TO FROTH MILK

n Fill the water tank and turn the machine on (fig. 1, 2, 3 and 4).

n After a few moments, the "on/off" light stops flashing and the "1 cup" and "2 cups" buttons light up.

n Press the “steam pre-heating” button. During preheating, the "on/off" and "steam pre-heating" lights

flash and the "1 cup" and "2 cups" lights go off (fig.12).

n Move the steam nozzle towards the outside of the appliance.

n Pour 60 to 100ml of cold fresh fat-free, low fat or whole milk in a small container that is about ½ litre

and can pass under the steam nozzle. The milk (UHT or pasteurised) and its container should be quite

cold.

n As soon as the device reaches the required temperature, the "on/off" and "steam pre-heating" lights

stop flashing.

n Place the steam nozzle in the milk and turn the knob to the “steam” position (fig. 13). The "steam pre-

heating" light will flash while steam is being produced.

n For a good result, hold the nozzle towards the bottom of the container for about 25 seconds while the

milk heats (without however touching the bottom of the container). Then, bring the container down

gradually so that the nozzle moves up towards the surface (without the nozzle coming out of the milk)

(fig.14).

n Once the froth has been formed, turn the knob to the “0” position (fig.15). The appliance will now

automatically cool itself by launching 3 intermittent pumping cycles. Once this automatic operation is

complete, you can make a coffee.

Important: To prevent the steam nozzle holes from being clogged, the milk foam must not reach the black

plastic upper part.

It is important to clean the steam nozzle after each use to prevent the milk from drying on the inside of the

nozzle. To do so:

n Place the steam nozzle in a container with water and repeat the milk frothing operation for 30 seconds.

WARNING!

The steam nozzle will be hot!

USING THE KRUPS XS-6000 AUTO-CAPPUCCINO SET TO FROTH MILK

The auto-cappuccino accessory makes it easier to make a cappuccino or a caffe latte. It is made up of a

special dual-position nozzle and a pipe.

n Fill the water tank and turn the machine on (fig. 1, 2, 3 and 4).

n Attach the auto-cappuccino accessory firmly to the arm.

n Place a cup under the self-cappuccino accessory.

n Pour approximately 100 ml of fresh, cold, fat-free, low fat or whole milk in a container.

n Immerse the pipe into the container, or directly into the carton of milk.

Note: Assemble the pipe firmly on the cappuccino accessory (fig.24).

n Turn the accessory's switch to the “cappuccino” or "latte" position.

n Press the “steam pre-heating” button. During preheating, the "on/off" and "steam pre-heating" lights

flash and the "1 cup" and "2 cups" lights go off (fig.12).

6. STEAM FUNCTION

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page8

English

n As soon as the device reaches the required temperature, the "on/off" and "steam pre-heating" lights stop

flashing. Turn the knob to the “steam” position (fig. 13). The milk is transferred from the container to the cup.

n Once the milk has been frothed, turn the knob to the “0” position (fig.15). The appliance will now

automatically cool itself by launching a number of intermittent pumping cycles. Once this automatic

operation is complete, you can make a coffee.

n To clean the auto-cappuccino device, please repeat the milk foaming procedure by replacing the 100ml

of milk with 100ml water.

n For thorough cleaning of the cappuccino accessory, see the paragraph "Cleaning and Maintenance".

n IMPORTANT: Your espresso machine accessories are not dishwasher-safe. Do not wash the spoon,

the drip tray, the filter holder and the water tank in the dishwasher.

CLEANING OF THE MACHINE

n Unplug the power supply before cleaning and let the appliance cool down.

n Clean the outside of the appliance from time to time with a damp cloth. After use, the water tank must

be emptied.

n Rinse inside the tank regularly.

n When a thin white layer starts to form in the tank, carry out a descaling operation (see paragraph 9

"DESCALING").

CLEANING OF THE DRIP TRAY

The drip tray must be emptied after each time the appliance is used. Lift up slightly and remove it from the

appliance.

If multiple espressos are prepared one after the other, it should be emptied from time to time (every 7 to

8 espressos approximately) (fig.19 and 20). The presence of water is normal and is not the sign of a leak.

If necessary, clean the drip tray and its grid with water and a little gentle washing-up liquid, rinse and dry.

When reassembling the components, make sure everything is in the right place.

CLEANING OF THE BREWING HEAD AND FILTER HOLDER

n They must be cleaned after each use. Simply wipe a damp cloth over the percolation head (fig. 21)

and clean the filter holder under running water and use a small amount of gentle washing-up liquid.

n Do not use alcohol or solvent-based cleaning products.

n For best results, you can activate the "EJECT" button several times during rinsing. We recommend that

you shake the filter holder thoroughly in order to remove all the water.

n Rinse and dry.

n When not using your espresso coffee maker, do not leave the filter holder fitted in the appliance, in

order to avoid wear to the seal

For more thorough cleaning, the filter holder can be dismantled:

n You can remove the black plastic part where the coffee outlets and the "EJECT" button are to be found:

turn it to the left and pull sharply (fig. 22).

n Clean the various components under running water and a little gentle washing-up liquid.

n Rinse and dry.

n Replace the black plastic part in the metal holder, turn it to the right until the two arrows on each

component line up.

If the percolation head is heavily clogged up, unscrew the grid using a screw-driver, clean it and refit it,

pressing down firmly (fig.23).

7. CLEANING AND MAINTENANCE

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page9

English

CLEANING OF THE STEAM NOZZLE

n This accessory consists of 2 parts: one part which is the plastic support and the other which is the

metal protection cylinder.

n Before cleaning, unlock the nozzle from the articulated arm by turning it to the left. (fig.16, 16.2)

n Then slide the metal cylinder along the plastic support (fig.16.3).

n Clean these two parts with tap water and some mild washing-up liquid (fig.17).

n Rinse and dry.

n Once the parts have been properly cleaned, put the metal cylinder back on the support.

n Make sure that you don’t damage the silicone seal which makes the nozzle watertight (fig.16.3).

n Insert the nozzle on the articulated arm then lock to the right (fig.18.1, 18.2).

CLEANING OF THE AUTO-CAPPUCCINO ACCESSORY

n For more thorough cleaning, the filter holder can be dismantled into 4 separate parts.

n Use water and a little gentle washing-up liquid and a small brush. Rinse it and dry it and then put it back

together.

n Note the direction in which the tube in inserted (fig.24).

The warranty does not cover machines which have become faulty because descaling was not periodically

performed.

Descale your espresso machine regularly using , available from Krups authorized service centers.

In addition to two packets of descaling powder, the kit also includes a water hardness tester to help you

determine the proper schedule for descaling your machine in normal use. The amount of scale that

develops depends on the hardness of the water used, but also the level of use. The schedule indicated

by the water hardness tester is a general guideline only. Keep in mind that you may have to descale more

frequently than indicated.

If in doubt, it is recommended to descale every month.

DESCALING THE MACHINE

n Empty the tank and replace.

n If you are using a Claris cartridge (model F088) in your water tank, remove the cartridge before

descaling.

n Follow the instructions for using the Krups descaling powder inside the kit.

n Then insert the filter holder (without espresso grounds) and lock into place by turning to the right. Place

a container under the steam nozzle to catch the water.

n Press the “on/off” button to turn the machine on. During the pre-heating phase, the indicator light will

flash. Once it stops blinking, turn the knob to the “steam” position (fig.13) and let 3.4 oz of this mixture

drain flow through (the equivalent of a mug) and then turn the knob back to the "0" position (fig.15).

n Place a container of sufficient volume under the filter holder.

n Once the light stops flashing, press the "2 cups" button and let the water flow through before repeating.

n Turn the appliance off by pressing the "On / Off" button immediately after this second cycle.

8. DESCALING

DESCALING FREQUENCY

Ave. number

coffees per week

Soft water

(<19°th)

Hard water

(19-30°th)

Very hard water

(>30°th)

Less than 7 Once a year Every 8 months Every 6 months

From 7 to 20 Every 4 months Every 3 months Every 2 months

Over 20 Every 3 months Every 2 months Every month

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page10

English

n After 15 minutes, turn the machine back on.

n Make the rest of the water run through into a recipient by pressing the "2 cups" button.

RINSING

IMPORTANT!

After descaling, perform 2-3 rinsing operations with clear water (without espresso

ground coffee), as described in paragraph 4 "USING".

Remember to rinse the steam circuit by following the instructions below:

n Place a container under the steam nozzle.

n Press the “on-off” button.

n Once the "on/off" light stops blinking, turn the knob to the “steam” position (fig.13) and let the water

drain through the nozzle until the steam begins to appear and then return it to the "0" position (fig.15).

The appliance is descaled and ready to be used again.

9. PROBLEMS, PROBABLE CAUSES AND CORRECTIVE ACTIONS

Problems Possible causes Solutions

The espresso is not

hot enough.

The cups and the filter

holder are cold.

Preheat the accessories: cups and filter holder (see

Section 5).

The filter holder is

locked.

You forgot to unlock the

filter.

Press “OPEN” while turning the filter holder to the

left.

The grounds are not

dry after water has

run through.

You have not tightened the

filter holder properly.

Tighten the filter holder by turning it to the right as

far as it will go.

The « on/off », « 1

cup » and « 2 cups »

buttons are flashing

and the machine

does not work.

The knob has been turned

the “steam” position.

Turn the knob to the “0” position (fig.15).

The coffee flows too

slowly.

The flow rate depends on

the fineness of the coffee

used and can vary when

preparing the espresso

The ground coffee is too

fine, too oily or floury.

The filter holder is dirty.

The water drip-through grid

is clogged.

Choose a larger grind of coffee. The perfect

espresso grind will feel like fine grains that do not

clump when pressed together.

Clean your filter holder (see Section 7).

When the machine has cooled, clean the brewing

head with a clean damp cloth (fig.21).

The water does not

run through.

No water in the tank.

The tank is not properly in

place.

The filter is clogged. The

ground coffee is too fine.

Your machine needs to be

descaled.

The Claris cartridge has been

replaced but not primed

Fill the tank.

Replace the tank in the correct position.

Clean the filter holder (see Section 7) and try a

larger grind of coffee.

Descale the machine (see Section 8).

See paragraph 4.

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:11 Page11

English

Water leaks from the

filter holder after an

espresso has been

made.

Your machine needs to be

descaled.

Descale the machine (see Section 8).

Coffee grounds in

the cup.

The filter holder is clogged.

The espresso grind is too

fine.

Clean the filter holder with hot water. Press

“EJECT” to eliminate the remnants of the grounds.

Shake to drain the water.

Choose a larger grind of coffee. The perfect

espresso grind will feel like fine grains that do not

clump when pressed together.

The water tank leaks

when it is carried.

The valve at the bottom of

the tank is dirty or defective.

The valve is blocked by lime

scale.

Wash the water tank and push on the valve at the

bottom of the tank to make sure it is not stuck.

Descale the machine (see Section 8).

Water leaks under

the machine.

Internal leak. Check the position of the tank. If the fault persists,

do not use the machine, contact an approved

service centre.

Water leaks under

the drip tray

Water can be present and/or

flow when you remove the

drip tray.This is not a sign of

a leak.

Crackles are heard

in the filter holder.

Normal phenomenon:

the filter holder security

lock.

The pump is

unusually noisy or

the 4 lights flash.

No water in the tank.

Tank poorly fitted.

The Claris cartridge is not

filled with water.

Stop the appliance, fill the water tank and turn the

machine back on.

Press down firmly on the tank.

Please refer to paragraph 4.

The cups are not

filled equally.

The filter holder is clogged. Clean the filter holder (see section 7).

Lots of water on the

ground coffee, in the

filter holder.

Coffee insufficiently tamped

down.

Insufficient amount of coffee.

Tighten the filter holder as far as it will go, up to

the stop (fig.7).

Add more espresso ground coffee.

The machine leaks

on the sides of the

filter holder.

The filter holder has not

been properly positioned.

The edge of the filter holder

is clogged by ground coffee.

Pod poorly positioned in the

filter.

The brewing head seal is

dirty.

The brewing head seal is

defective.

Put the filter holder in place and lock it (by turning

it to the right as far as it will go, up to the stop).

Remove excess coffee.

Place all the paper inside the filter holder.

Clean the seal with a damp cloth.

Contact a Krups approved service centre.

Problems Possible causes Solutions

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:12 Page12

English

Problems Possible causes Solutions

Your espresso

tastes bad.

After descaling, the rinsing

was not performed properly.

Rinse the machine carefully after descaling (see

Section 8).

The espresso has

no froth (crema on

coffee).

Coffee grounds too coarse,

stale or too dirty.

Try fresher or finer espresso coffee grounds.

The appliance does

not work

The pump was unprimed

due to lack of water.

The detachable water

compartment is not properly

clicked in place.

The Claris cartridge has

been replaced but not

primed.

Fill the water tank and reprime the pump (see

paragraph 4). Avoid completely emptying the tank.

Click the tank into place by pressing firmly.

See paragraph 4.

The steam nozzle

does not froth the

milk.

The steam nozzle is

clogged or needs to be

descaled

The milk is not fresh

enough.

The shape of the container

is not appropriate.

The milk is not cold or fresh

enough.

The steam nozzle is not

properly clipped onto the

arm.

The auto-cappuccino

accessory is poorly fitted.

Carefully clean (see Section 7) or descale the

steam nozzle (see Section 8).

Use fresh cold milk.

Use a small stainless steel jug.

Use very cold, very fresh milk. Try using a different

brand of milk.

Clip it firmly onto the arm (fig.18.1,18.2).

Insert it firmly into the articulated arm.

10. DISPOSING OF YOUR MACHINE

Environmental protection first!



Your machine contains a lot of recoverable or recyclable material.



When disposing of your machine, consult your local waste collection agency to determine the

proper method of recycling and/or disposal.

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:12 Page13

English

: www.krups.com

With a strong commitment to the environment, most of Krups products are

repairable during and after the warranty period. Before returning any defective

products to the point of purchase, please call Krups consumer service directly

at the phone number below for repair options.

Your help to sustain the environment is appreciated!

The Warranty

This product is guaranteed by Krups for a period of 2 years against any manufacturing defect

in materials or workmanship, starting from the initial date of purchase.

The manufacturer's warranty by Krups is an extra benefit which does not affect consumer's Sta-

tutory Rights.

The Krups warranty covers all costs related to restoring the proven defective product so that it

conforms to its original specifications, through the repair or replacement of any defective part

and the necessary labor. At Krups’s choice, a replacement product may be provided instead of

repairing a defective product. Krups’s sole obligation and your exclusive resolution under this

warranty are limited to such repair or replacement.

Conditions & Exclusions

The Krups warranty only applies within USA, Canada & Mexico, and is valid only on presenta-

tion of a proof of purchase. The product can be taken directly in person to an authorized

service centre or must be adequately packaged and returned, by recorded delivery (or equiva-

lent method of postage), to a Krups authorized service centre. Full address details for each coun-

try’s authorized service centre are listed on the Krups website (www.krups.com

) or by calling the

appropriate telephone number listed below to request the appropriate postal address.

Krups shall not be obliged to repair or replace any product which is not accompanied by a valid

proof of purchase.

This warranty will not cover any damage which could occur as a result of misuse, negligence,

failure to follow Krups instructions, use on current or voltage other than as stamped on the pro-

duct, or a modification or unauthorized repair of the product. It also does not cover normal tear

and wear, maintenance or replacement of consumable parts, and the following:

-using the wrong type of water

-scaling (any de-scaling must be carried out according to the instructions for use);

-ingress of water, dust or insects into the product;

-mechanical damages, overloading

-damages or bad results due to wrong voltage or frequency

-accidents including fire, flood, lightning, etc

-professional or commercial use

-damage to any glass or porcelain ware in the product

This warranty does not apply to any product that has been tampered with, or to damages in-

curred through improper use and care, faulty packaging by the owner or mishandling by any car-

rier.

KRUPS MANUFACTURER'S WARRANTY

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:12 Page14

The Krups manufacturer's warranty applies only for products purchased and used in USA, Canada

& Mexico. Where a product purchased in one country and then used in another one:

a) The Krups guarantee duration is the one in the country of usage of the product, even if the

product was purchased in another listed country with different guarantee duration.

b) The Krups guarantee does not apply in case of non conformity of the purchased product

with the local standards, such as voltage, frequency, power plugs, or other local technical

specifications

c) The repair process for products purchased outside the country of use may require a lon-

ger time if the product is not locally sold by Krups

d) In cases where the product is not repairable in the new country, the Krups guarantee is li-

mited to a replacement by a similar product or an alternative product at similar cost, where

possible.

Consumer Statutory Rights

This Krups manufacturer's warranty does not affect the statutory rights a consumer may have or

those rights that cannot be excluded or limited, nor rights against the retailer from which the consu-

mer purchased the product. This warranty gives a consumer specific legal rights, and the consu-

mer may also have other legal rights which vary from State to State or Country to Country or

Province to Province. The consumer may assert any such rights at his sole discretion.

Additional information

Accessories, Consumables and end-user replaceable parts can be purchased, if locally available,

as described in Krups internet site.

: www.krups.com

CANADA

GROUPE SEB

CANADA

345 Passmore Avenue

Toronto, ON

M1V 3N8

MEXICO

Groupe SEB MEXICO

S.A. de C.V.

Goldsmith 38 Desp.

401 Col. Polanco

Delegacion Miguel

Hildalgo

11 560 Mexico D.F.

MEXICO

U.S.A.

GROUPE SEB USA

2121 Eden Road

Millville, NJ 08332

1-800-418-3325 01800 1128325 800-526-5377

English

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:12 Page15

English

KR_XP52_AUTOMATIC_NAFTA_NC00026257-01 18/11/11 14:12 Page16

La page charge ...

Krups AUTOMATIC XP52 Series Manuel utilisateur

Marque: Krups

Modèle: AUTOMATIC XP52 Series

Catégorie: Cafetières

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Krups AUTOMATIC XP52 Series User manual
español: Krups AUTOMATIC XP52 Series Manual de usuario

Krups AUTOMATIC XP52 Series Manuel utilisateur

Ce manuel convient également à

Krups AUTOMATIC XP52 Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents