Krups XP228050 Manuel utilisateur

Marque: Krups

Modèle: XP228050

Catégorie: Cafetières

Taper: Manuel utilisateur

Français

www.krups.com

NC00026071-01

English . . . . . . . . . . . . . . . . . . p. 1

Français . . . . . . . . . . . . . . . . . p. 19

Español . . . . . . . . . . . . . . . . . p. 37

Espresso Coffee

Auto

Prog

Auto

eject

C D

open

Réalisation : Espace Graphique

WWW.KRUPS.COM

XP2280

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:54 PageC1

Auto

fig. 6

fig. 1 fig. 2

fig. 3

fig. 5

fig. 11

fig. 7

fig. 10

fig. 8 fig. 9

fig. 4

fig. 12

fig. 20

fig. 16.2

fig. 18.1 fig. 18.2

fig. 17

uto

rog

uto

fig. 13

fig. 15

fig. 19

fig.21

fig. 14

fig. 16.3

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:54 PageC4

fig. 27

fig. 25

uto

fig. 26

fig. 28

fig. 22

fig. 23

. 2

fig. 24

fig. 23

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 PageC7

English

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to

reduce the risk of fire, electric shock, and/or injury to persons including the following :

1. Read all instructions prior to first use.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against fire, electric shock and injury to persons, do not immerse cord,

plugs or machine in water or other liquid.

4. Not intented for use by children.

5. Close supervision is necessary when any machine is used near children. Keep

machine out of reach of children.

6. This appliance is not designed to be used by people (including children) with a

physical, sensory or mental impairment, or people without knowledge or experience,

unless they are supervised or given prior instructions concerning the use of the

appliance by someone responsible for their safety.

7. Children must be supervised to ensure that they do not play with the appliance.

8. Burns can occur from touching hot plate, hot water or steam. Exercise caution.

9. Exercise caution when using the steam nozzle as steam can cause scalding.

10. Unplug machine from outlet when not in use and when cleaning. Allow to cool before

putting on or taking off parts, before cleaning the machine, and before storing.

11. All machines are subject to stringent quality control. Practical tests using machines

taken at random are conducted and this may explain any slight marks or coffee

residue prior to use.

12. Do not operate any machine with a damaged cord or plug or after the machine

malfunctions, or has been damaged in any manner. Return machine to the nearest

Krups Service Center for examination, repair or adjustment or your respective

countries Consumer Service Department.

13. To reduce the risk of injury do not drape cord over the counter top or table top where

it can be pulled on by children or tripped over accidentally.

14. Do not let cord hang over edge of table or counter, or touch hot surfaces.

15. The use of accessory attachments not recommended by Krups may result in fire,

electric shock or injury to persons.

16. Do not use outdoors.

17. Do not place on or near a hot gas or electric burner, or in a heated oven.

18. To disconnect the machine, turn the control to “off” then remove plug from wall outlet.

Do not yank cord, instead grasp plug and pull to disconnect.

19. Do not use the machine for other than intended use.

20. Do not pour liquids other than water and descaling solutions specified in this manual

into the water tank.

21. Protect the machine against humidity and freezing.

22. This machine is for household use only.

SAVE THESE INSTRUCTIONS

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page1

English

CAUTION

This machine is intended for household use only. Any servicing other than cleaning and

user maintenance should be performed by the nearest authorized Krups Service Center.

Visit our website at www.krupsusa.com in the USA or www.krups.ca in Canada or

contact your respective country's Consumer Service department for the service center

nearest to you.

To reduce the risk of fire or electric shock, do not attempt to disassemble the machine.

Repair should be done by an authorized Krups Service Center only.

SHORT CORD INSTRUCTIONS

A.We do not recommend using an extension cord with this device.

B.If an extension cord is absolutely necessary,

1) the marked electrical rating of the extension cord should be at least as great

as the electrical rating of the machine,

2) the longer cord should be arranged so that it will not drape over the counter

top or table top where it can be pulled on by children or tripped over.

C.This machine has a polarized plug (one blade is wider than the other). To reduce

the risk of electric shock, this plug is intended to fit into a polarized outlet only

one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does

not fit, contact a qualified electrician. Do not attempt to modify the plug in any

way.

In the interest of improving products, Krups reserves the right to change specifications

without prior notice.

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page2

English

DESCRIPTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 4

TECHNICAL INFORMATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 4

ESPRESSO PART

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 5

TIPS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 5

1. USING FOR THE FIRST TIME

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 5

2. MAKING AN ESPRESSO

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 6

3. STEAM FUNCTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p. 8

4. CLEANING AND MAINTENANCE OF THE APPLIANCE . . . . . . . . . . . . . . . p. 9

5. DESCALING

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.10

6. PROBLEMS, PROBABLE CAUSES AND CORRECTIVE ACTIONS

. . . . . p.12

FILTER COFFEE MAKER PART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.15

BEFORE USING FOR THE FIRST TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p 15

MAKING COFFEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.15

SETTING THE TIME FOR A PREPROGRAMMED START . . . . . . . . . . . . . . . . p.15

PREPROGRAMMED START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.15

CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.15

DESCALING THE FILTER COFFEE MAKER . . . . . . . . . . . . . . . . . . . . . . . . . . . p.16

IN CASE OF PROBLEM: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.16

END OF LIFE ELECTRICAL AND ELECTRONIC PRODUCT . . . . . . . . . . . . . . . p 16

TABLE OF CONTENTS

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page3

English

n Pump: 15 bars

n KTS: Krups Tamping System, for an automatic and optimal tamping of ground coffee

n Filter holder with coffee grounds ejection system. Compatible with ground coffee and all types of

pods (E.S.E. or soft).

n Steam function

n Automatic shutoff.

n Removable tank (capacity: 1.1 litre)

n Power: 1450 W

n Voltage: 120 V - 50/60 Hz

n Overheating safety devices

n Dimensions: H. 320 mm, L. 354 mm, W. 290 mm

IMPORTANT!

Operating voltage: This appliance is designed to operate solely with an alternating

current of 120V.

Type of use: This appliance is designed for DOMESTIC USE ONLY.

TECHNICAL CHARACTERISTICS

ESPRESSO

a- Espresso and coffee maker tank lid

b - Removable water tank

c - Measuring spoon

d - Cup warming plate

f - Control panel

f1 - Espresso on/off button

f2 - 1 cup button

f3 - 2 cups button

f4 - Steam preheating button

g - Steam function knob

h - Brewing head

i - Filter holder

j - Drip tray grid

k - Drip tray with level indicator

l - Steam nozzle

m- Auto-Cappuccino accessory

FILTER COFFEE MAKER

A- Filter holder lid

B - Lid opening button

C - Coffee maker tank

D - Container for “Duo Filter XS1000” water filter

(filter not provided)

E - Filter holder with carrying handle

F - Calibrated water level indicator for the coffee

maker tank

G - Control panel

G1 - Coffee maker on/off button

G2 - "H" hours and "m" minutes buttons for set-

ting the clock

G3 - Button to activate preprogrammed start

G4 - Button to set the time for a preprogrammed

start

G5 - Aroma selector button

H - Calibrated jug

I - Keep-warm hot plate

Espresso

Coffee

DESCRIPTION

Your Krups espresso machine is equipped with a filter-holder that has three patented systems designed to

help you make the perfect espresso at home.

1. KRUPS Precise Tamp: gradual tamping of the espresso ground coffee as the filter-holder is turned en-

sures that coffee is tamped precisely each time.

2. Coffee ejection system under the filter-holder for clean removal of the cake each time.

3. The filter-holder is compatible with all types of pods including E.S.E. and soft pods.

The filter-holder is also removable and can be frequently cleaned to maintain the filter-holder system in per-

fect working order. For your safety, the filter-holder is equipped with a locking system when pressure rises.

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page4

English

ESPRESSO

TIPS

n For an intensely aromatic espresso, we recommend that you use freshly ground special espresso

coffee which is ideal for preparing this type of delicate beverage, as well as cups with a capacity not

exceeding 50 ml.

n Keep the ground coffee in the refrigerator to preserve its aroma longer.

n Do not fill your filter holder to the brim, but use the measuring spoon (1 cup = 1 spoon –2 cups =

2 spoons) (Fig. 5).

n If you do not use the appliance for more than 5 days, rinse and drain the water tank.

n Always remember to turn off the appliance before removing the tank to fill or empty it.

n Make sure you always place the appliance on a flat stable surface.

n To obtain an espresso at exactly the right temperature, we recommend that you preheat your cups.

n To prolong the service life of your appliance, we recommend that you always use a Claris Aqua Filter

System cartridge (reference: F088) and that you descale the appliance at regular intervals.

IMPORTANT!

Before using for the first use, after a prolonged period of inactivity or after descaling,

the appliance must be cleaned as described in paragraph 1: "BEFORE FIRST USE".

Before using your espresso machine, clean all the accessories in soapy water and dry them.

A. SETTING THE TIME (to be done on first use and after a power cut)

n Your XP2280 combo machine has a display making it easy to use and providing a wide range of

settings.

n You must set the clock when you plug in your appliance for the first time or after a power cut.

n You can set the clock in European (24-hour clock) or American (AM-PM) display mode.

n To do this, simultaneously press the "H" and "m" buttons below the display.

n Then set the hours by pressing the "H" button and the minutes by pressing the "m" button.

Make sure the steam knob on the left of the appliance is in 0 position.

If you are not using the Claris cartridge, go directly to paragraph "C. RINSING YOUR

APPLIANCE".

B. INSTALLING THE CLARIS CARTRIDGE (to be done every time the cartridge is replaced)

n Screw the Claris cartridge into the bottom of the tank.

n Fill the tank with water (Fig. 2).

n Replace the tank by positioning it firmly to ensure that water can enter and then close the lid (Fig. 3).

n Place a container under the steam nozzle.

n Turn on the appliance by pressing the button (fig.4).

n As soon as the appliance reaches the right temperature, the LED glows steadily and the

pictograms and are displayed.

n Turn the knob on the side of the appliance to (fig.13).

n At the start, steam will come out through the steam nozzle and the four pictograms in the display and

the LED will begin to flash.

n Turn the knob to "0" position (fig.15).

n Turn off the machine and then turn it on again by pressing the button twice.

n Return to knob to : position: water flows out of the steam nozzle. If water does not flow from the

nozzle, repeat the operation from the start 1 or 2 times.

Espresso

1. BEFORE FIRST USE

Espresso

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page5

English

n Turn the knob to "0" position.

In this manner you can be sure that water is circulating well through the filter cartridge.

IMPORTANT:

This installation procedure must be carried out every time the cartridge is

replaced.

The Claris cartridge needs to be replaced every 2 to 3 months if it is used daily.

C. RINSING YOUR APPLIANCE (to be done on first use and after each cleaning /

descaling operation)

- RINSING OUT THE ESPRESSO CIRCUIT

n Turn on the appliance and fill the water tank (Fig. 1, 2, 3 & 4).

n Insert the filter holder (without ground coffee) in the appliance (Fig. 7).

n Place a container of sufficient volume under the filter holder.

n As soon as the appliance reaches the right temperature, the LED glows steadily and the

pictograms and are displayed.

n Press the button and let the water run out into the container (fig.9).

n Repeat this operation 5 times.

n If necessary, stop the operation by pressing the button to empty the container and then resume

the operation (fig.9).

n Empty the container and unlock the filter holder: press the "OPEN" button on the filter holder and

turn it to the left (fig.10).

RINSING OUT THE STEAM CIRCUIT.

Before using the steam function for the first time, the steam circuit should be cleaned.

n Fill the water tank. Make sure that the steam function dial is in O position.

n Turn the appliance on by pressing the button.

n Place a container underneath the steam nozzle.

n When the light indicator glows, press the button: the light indicator and the pictogram

on the display will begin to blink.

n When they have stopped blinking, turn the dial to the position and allow the water to flow until

steam is generated.

n Keep the steam production going for at least 30 seconds.

Before making an espresso, make sure the steam knob on the left of the appliance is in 0

position.

In order to release all the aromas of the coffee and ensure your complete satisfaction, this machine pre-

brews each coffee. The pump works for 3 seconds, stops the following 3 seconds and then the cycle

continues until the end of the preparation.

PREHEATING THE ACCESSORIES

n For best results, we recommend that you first pre-heat the accessories (filter holder and cups)

without ground coffee. To do this:

n Fill the water tank and turn on the appliance (Fig. 1, 2, 3 and 4).

n Put the filter holder in place and place the cups underneath.

n As soon as the appliance reaches the right temperature, the LED glows steadily and the

pictograms and are displayed.

n Then press the or button (fig.8 ou 9).

n Once the cup(s) are filled with hot water, remove them.

n Unlock the filter holder: press the "OPEN" button by turning the filter holder to the left and remove

it from the appliance.

Espresso

2 . MAKING AN ESPRESSO

Espresso

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page6

English

WITH GROUND COFFEE

The type of ground coffee you use will determine the strength and taste of your espresso.

n Fill the water tank and turn on the appliance (Fig. 1, 2, 3 and 4). During the preheating of the

appliance, the LED flashes.

n Using the measuring spoon, place the ground coffee in the filter holder: one measuring spoon (full

to the brim) per cup (Fig. 5).

n Remove any excess ground coffee from the edge of the filter holder.

IMPORTANT:

Do not tamp the ground coffee down into the filter holder. the coffee is

automatically tamped using the KTS "Krups Tamping System".

nInsert the filter holder into the appliance by turning it as far as possible to the right, up to the stop

(Fig. 7).

nPlace one or two cups under the filter holder.

nAs soon as the appliance reaches the right temperature, the LED glows steadily and the

pictograms and are displayed.

nThen press the or button (fig.8 ou 9).

nThe coffee will stop flowing when the preprogrammed volume of 50 ml per cup is reached; to change

this volume, see chapter “Individual programming of the volume of water”.

nWhen the coffee is flowing, the pictograms or show that the cup(s) are being filled.

nOnce the cup(s) are filled, unlock the filter holder: press the "OPEN" button by turning the filter holder

to the left and remove it from the appliance (Fig. 10).

nThrow away the used coffee using the ejection system by pressing the "EJECT" button between the

two coffee outlet nozzles (Fig. 11).

nWash the filter holder under running water, while pressing the "EJECT" button to eliminate the

remnants of ground coffee.

nThe filter holder can now be filled again to prepare more espressos.

Note: You can always stop the coffee flowing by pressing the or button again.

IMPORTANT

If you want a strong or light espresso, vary the quantity of coffee or water (full

spoon for a strong espresso and a less full spoon for a light espresso). But in both

cases, be sure to tighten your filter holder as much as possible.

WITH AN "E.S.E." ESPRESSO POD

"E.S.E." for "Easy Serving Espresso" is a special espresso pod in rigid packaging (44 mm dia-

meter) of 7g of selected coffee, ground and compacted between two paper filters, specially

designed to make Italian style ristretto (tight) espressos.

This system allows an immediate, simple, clean and comfortable use of your machine.

n Fill the water tank and turn on the appliance (Fig. 1, 2, 3 and 4). During the preheating of the

appliance, the LED flashes.

n If necessary, tear the excess pre-cut paper off the pod, put the E.S.E. pod into the filter holder, wtih

the red writing if any facing down (Fig. 6).

n Be sure to place all the paper inside the filter holder, otherwise there might be leaks.

n If the pod is not positioned correctly, the result in the cup will not be satisfactory.

n Never use two pods together.

n Follow the steps in Figures 7 to 11 for preparing an espresso.

Note: Once you have obtained the sufficient amount of coffee, you can stop the flow at any time by

pressing the button (fig.8).

Espresso

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page7

English

WITH A SOFT POD

Your machine is also compatible with soft pods (usually 60 mm in diameter). Given that this

kind of pod is not specifically designed for espresso machines, you will get a less strong es-

presso than with an E.S.E. pod.

n Fill the water tank and turn on the appliance (Fig. 1, 2, 3 and 4). During the preheating of the

appliance, the LED flashes.

n Place a soft pod in the filter holder. Never use two pods together.

n Be sure to place all the paper inside the filter holder, otherwise there might be leaks.

n If the pod is not positioned correctly, the result in the cup will not be satisfactory.

n Follow the steps in Figures 7 to 11 for preparing an espresso.

Note: Once you have obtained the sufficient amount of coffee, you can stop the flow at any time by

pressing the button (fig.8).

INDIVIDUAL PROGRAMMING OF THE VOLUME OF WATER:

To change the preprogrammed amount of water (50 ml per cup is the factory setting), proceed as fol-

lows:

n Fill the water tank and turn on the appliance (Fig. 1, 2, 3 and 4).

n Put a spoonful of coffee in the filter holder using the measuring spoon or use an E.S.E. or soft pod.

n Put the filter holder in place by turning it to the right as far as possible, up to the stop (Fig. 7).

n Place a cup under the filter holder.

n Hold down the button ( > 3 sec) until the pictogram flashes quickly. The coffee flows out.

n When the desired amount of espresso is obtained, press the . button. This amount will then be

saved automatically.

n The next time you press the , button, you will obtain the most recently recorded amount.

n You can program for 2 cups in the same manner, by pressing the button ( > 3 sec).

n Steam is used to foam up the milk (for example, to make a cappuccino or a cafe latte).

n To produce steam, the pump works by emitting an intermittent noise.

n After using the steam function, the appliance cools automatically by pumping cold water

through the heating system. During the pumping cycles, the excess steam in the heating system is

released with the hot water into the drip tray.

n The release of steam and the accompanying noise are required for the appliance to cool

down.

WARNING:

During and after using the appliance, the metal parts of the steam nozzle can

become very hot.

USING THE STEAM NOZZLE TO FROTH MILK

n Fill the water tank and turn on the appliance (fig.1, 2, 3 et 4).

n After a few moments, the button glows steadily

n Press the button (fig. 12). During the pre-heating, the LED and the pictogram flash.

n Move the steam nozzle towards the outside of the appliance.

n Pour 60 to 100 ml of semi-skimmed milk in a narrow container of about 1/2 litre and which can pass

under the steam nozzle. The milk (UHT or pasteurised) and its container should be quite cold.

n As soon as the appliance reaches the right temperature, the LED and the pictogram glow

steadily.

n Immerse the steam nozzle into the milk and turn the knob to

position

(fig.13).

Espresso

3 . STEAM FUNCTION

Espresso

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page8

English

n The LED and the pictogram remain steady when the steam begins to be produced and can

flash after a few moments.

n For best results, hold the nozzle towards the bottom of the container for about 25 seconds while the

milk heats up (without however touching the bottom of the container). Then, bring the container down

gradually so that the nozzle moves up towards the surface (without the nozzle coming out of the milk)

(Fig. 14).

n Once the froth has been formed, turn the knob to "0" position (Fig. 15). The appliance will now

automatically cool down by launching intermittent pumping cycles. Once this automatic operation is

complete, you can make a coffee.

IMPORTANT : To prevent the steam nozzle from being clogged, the milk foam must

never reach the black plastic upper part.

It is important to clean the steam nozzle after each use to prevent the milk from drying on the inside of the

nozzle. To do this:

n Place the steam nozzle in a container with water and repeat the milk frothing operation for 30 seconds.

WARNING!

The steam nozzle will be hot!

USING THE AUTO-CAPPUCCINO ACCESSORY TO FROTH MILK

The auto-cappuccino accessory makes it easy to prepare a cappuccino or a caffe latte. It comprises a

special dual-position nozzle and a pipe.

n Fill the water tank and turn on the appliance (Fig. 1, 2, 3 and 4).

n Attach the auto-cappuccino accessory firmly to the articulated arm.

n Place a cup under the auto-cappuccino accessory.

n Pour about 100 ml of cold semi-skimmed milk into a container.

n Immerse the pipe into the container, or directly into the carton of milk.

Warning:

Assemble the pipe firmly on the cappuccino accessory (fig.24).

n Turn the accessory’s switch to “cappuccino” or “latte” position.

n Press the “steam preheating” button (Fig. 12). During the pre-heating, the LED and the

pictogram flash.

n As soon as the appliance reaches the right temperature, the LED and the pictogram glow

steadily. Turn the knob to position (Fig. 13). The milk is transferred from the container to the cup.

n Once the froth has been formed, turn the knob to “0” position (Fig. 15). The appliance will now

automatically cool down by launching intermittent pumping cycles. Once this automatic operation is

complete, you can make a coffee.

n To clean the auto-cappuccino accessory, please repeat the procedure for frothing milk, but this time with

100 ml of water instead of 100 ml of milk.

n For more thorough cleaning of the auto cappuccino accessory, please refer to the section “Cleaning and

Maintenance”.

Do not wash your espresso machine accessories in the dishwasher.

Espresso

4 . CLEANING AND MAINTENANCE

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page9

English

CLEANING YOUR APPLIANCE

n Unplug the power supply before cleaning and let the appliance cool down.

n Clean the outside of the appliance from time to time with a damp cloth. After use, the water tank must

be emptied.

n Rinse the inside of the tank regularly.

n When a thin white layer starts to form in the tank, carry out a descaling operation (see paragraph 5.

"DESCALING").

CLEANING THE DRIP TRAY

n The drip tray must be emptied after each time the appliance is used. Lift it up slightly and remove it

from the appliance.

n If multiple espressos are prepared one after the other, it should be emptied from time to time (every

7 to 8 espressos approximately) (Fig. 19 & 20).

n The presence of water is normal and is not the sign of a leak.

n If necessary, clean the drip tray and its grid with water and a small amount of gentle washing-up

liquid, rinse and dry. When reassembling the components, make sure everything is in the right place.

CLEANING THE BREWING HEAD AND FILTER HOLDER

n The brewing head and filter holder must be cleaned after each use. Simply wipe a damp cloth over

the brewing head (Fig. 21) and clean the filter holder with clean water and a small amount of gentle

washing-up liquid.

n Do not use alcohol- or solvent-based cleaning products.

n For best results, you can press the "EJECT" button several times during rinsing.

We recommend that you shake the filter holder thoroughly in order to remove all the water.

n Rinse and dry.

n When not using your espresso machine, do not leave the filter holder fitted in the appliance in order

to avoid wear to the seal.

For more thorough cleaning, the filter holder can be dismantled fully:

n You can remove the black plastic part where the coffee outlets and the "EJECT" button are found:

turn it to the left and pull sharply (Fig. 22).

n Clean the various components with clean water and a small amount of gentle washing-up liquid.

n Rinse and dry.

n Replace the black plastic part in the metal holder, turn it to the right until the two arrows on each

component line up.

n If the brewing head is clogged, unscrew the grid using a screwdriver, clean it and refit it tightening

it firmly (Fig. 23).

CLEANING THE STEAM NOZZLE

n This accessory consists of 2 parts: one part which is the plastic support and the other which is the

metal protection cylinder.

n Before cleaning, unlock the nozzle from the articulated arm by turning it to the left (fig.16, 16.2).

n Then slide the metal cylinder along the plastic support (fig.16.3).

n Clean these two parts with tap water and some mild washing-up liquid (fig.17).

n Rinse and dry.

n Once the parts have been properly cleaned, put the metal cylinder back on the support.

n Make sure that you don’t damage the silicone seal which makes the nozzle watertight (fig.16.3).

n Insert the nozzle on the articulated arm then lock to the right (fig.18.1, 18.2).

CLEANING THE AUTO CAPPUCCINO ACCESSORY

n For more thorough cleaning, the auto cappuccino accessory can be dismantled into four separate

parts.

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page10

English

n Clean it with water, a little gentle washing-up liquid and a small brush. Rinse and dry it before putting

it back in place.

n Note the direction in which the pipe is inserted (fig.24)

The guarantee does not cover appliances which become faulty because they have not been descaled

regularly.

Descale your espresso machine using white vinegar or a sachet of commercial citric or sulfamic acid.

We recommend that you use the Krups descaling accessory, reference F054, available in Krups

authorized service centres (to Krupsonlinestore.ca for Canadian residents only). In addition to two des-

caling sachets, this accessory includes a water hardness tape tester to assess the frequency with which

your appliance should be descaled, in normal use. The amount of scale depends on the hardness of the

water but also the level of use.

The frequency of descaling given by the F054 accessory is therefore purely indicative.

If in doubt, it is recommended to descale every month

DESCALING THE STEAM AND ESPRESSO CIRCUIT

n Empty the tank and put it back in place.

n If your appliance is fitted with our Claris - Aqua Filter System F088 cartridge, please remove this

cartridge before the descaling operation.

n Fill the tank with a mixture composed of three parts of water for one part of white vinegar or a mixture

of 1/2 litre of water and a sachet of commercial descaling agent.

n Insert the filter holder (without ground coffee) into the appliance and lock it by turning it to the right,

up to the stop.

n Place a container under the steam nozzle.

n Press the . button. During the preheating of the appliance, the LED flashes.

n Once it becomes steady, turn the knob to position and let 100 ml of this mixture flow through (the

equivalent of a mug) and then turn the knob back to "0" position.

n Place a container of sufficient volume under the filter holder.

n When the LED becomes steady, press the , button and let the water flow through before

repeating this operation.

n Turn off the appliance by pressing the button immediately after this second cycle.

n After 15 minutes, turn the appliance back on.

n Press the button. During the preheating of the appliance, the LED flashes. When it

becomes steady, make the rest of the mixture run through into a container by pressing the

button several times.

RINSING

IMPORTANT !

After descaling, perform 2-3 rinsing operations with clean water (without

espresso ground coffee), as described in paragraph 1 "Before first use".

Remember to rinse the steam circuit by following the instructions below:

n Place a container under the steam nozzle.

5. DESCALING

DESCALING FREQUENCY

Av. number of

coffees per week

Soft water

(<19°th)

Hard water

(19-30°th)

Very hard water

( 30°t)

Less than 7 Once a year Every 8 months Every 6 months

From 7 to 20 Every 4 months Every 3 months Every 2 months

Over 20 Every 3 months Every 2 months Every month

EspressoEspresso

Espresso

EspressoEspresso

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page11

English

n Press the button (fig.4).

n Once the LED becomes steady, turn the knob to position and let 100 ml of water flow through

the nozzle and then turn it back to "0" position

n The appliance is descaled and ready to be used again.

Espresso

6. TROUBLESHOOTING

Problems Possible causes Solutions

The espresso is not

hot enough.

The cups and the filter

holder are cold.

Preheat the accessories: cups and filter holder

(see paragraph 6).

The LED and

the pictograms

and flash and

the appliance does

not work.

Espresso

The knob has been turned

to the position.

Turn the knob to the “0” position (fig.15).

The filter holder is

blocked

You forgot to unlock the

filter.

Press the "OPEN" button lightly while turning the

filter holder to the left.

The grounds are not

dry after water has

run through.

You have not tightened the

filter holder properly.

Tighten the filter holder further by turning it to the

right as far as possible, up to the stop.

The espresso flows

too slowly.

The espresso ground coffee

is too fine, too oily or floury.

The flow rate depends on

the fineness of the coffee

used and can vary when

preparing the espresso

The filter holder is dirty.

The water drip-through grid

is clogged.The water drip-

through grid is clogged.

Choose a slightly coarser espresso ground

coffee

Clean your filter holder (see paragraph 4).

When the appliance has cooled, clean the

brewing head with a damp cloth. (fig.21).

The water does not

run through.

No water in the tank.

Tank poorly fitted.

The filter is clogged. The

espresso ground coffee is

too fine.

Your device is scaled up.

The Claris cartridge has

been replaced but not

primed.

Fill the tank.

Press down firmly on the tank.

Clean the filter holder (see paragraph 4) and try a

less fine espresso grind.

See paragraph 5.

See paragraph 1

Water leaks from

the filter holder after

an espresso has

been made.

Premature formation of

scale due to especially hard

water.

Descale your appliance according to the manual

(see paragraph 5).

Coffee grounds in

the cup.

The filter holder is clogged.

The grind is too fine.

Clean the filter holder with hot water. Press

“EJECT” to eliminate the remnants of the

grounds. Shake to drain the water.

Use a slightly coarser espresso grind.

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page12

English

The water tank leaks

when it is moved.

The valve at the bottom of

the tank is dirty or defective.

The valve is blocked by

scale.

Wash the water tank and operate the valve at the

bottom of the tank with your finger.

Descale the appliance (paragraph 5).

Water leaks under

the appliance.

Internal leak. Check the position of the tank. If the fault persists,

do not use the appliance, contact an approved

service centre.

Water leaks under

the drip tray

Water can be present

and/or flow when you

remove the drip tray.This is

not a sign of a leak.

Crackles are heard

in the filter holder.

Normal phenomenon:

the filter holder security

lock.

The pump is

abnormally noisy or

the LED and the

pictograms ,

, flash.

Espresso

No water in the tank.

Tank poorly fitted.

The Claris cartridge is not

filled with water.

Stop the appliance, fill the water tank and turn

the machine back on.

Press down firmly on the tank.

Please refer to paragraph 1.

The cups are not

filled equally.

The filter holder is clogged. Clean the filter holder (see paragraph 4).

Lots of water on the

ground coffee, in the

filter holder.

Coffee insufficiently tamped

down.

Insufficient amount of

coffee.

Tighten the filter holder as far as it will go, up to

the stop (fig.7).

Add more espresso ground coffee.

The espresso leaks

on the sides of the

filter holder.

The filter holder has not

been properly positioned.

The edge of the filter holder

is clogged by ground

coffee.

Pod poorly positioned in the

filter.

The brewing head seal is

dirty.

The brewing head seal is

defective.

Put the filter holder in place and lock it (by

turning it to the right as far as it will go, up to the

stop).

Remove excess coffee.

Place all the paper inside the filter holder.

Clean the seal with a damp cloth.

Contact a Krups approved service centre.

Problems Possible causes Solutions

Your espresso

tastes bad.

After descaling, the rinsing

was not performed properly.

Rinse the appliance according to the manual

(see paragraph 5).

Your espresso has

no cream (froth).

Coffee grounds too coarse,

stale or too dirty.

Try fresher or finer espresso coffee grounds.

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page13

English

Problems Possible causes Solutions

The steam nozzle

does not froth the

milk.

The steam nozzle is blocked

or scaled up

The milk is too hot.

The shape of the container

is not appropriate.

You are using skimmed milk.

The steam nozzle is not

properly clipped onto the

articulated arm.

The auto cappuccino

accessory is assembled

incorrectly

Descale the steam nozzle (see paragraph 5) or

unblock it using a needle.

Use cold milk.

Use a small jug.

Preferably use whole or semi-skimmed milk.

Use very cold, very fresh milk. Try using a

different brand of milk.

Clip it firmly onto the articulated arm (Fig. 18.1,

18.2).

Insert it firmly into the articulated arm

The appliance does

not work

The pump was unprimed

due to lack of water.

The Claris cartridge has

been replaced but not

primed.

The removable water tank is

not properly clicked in

place.

Fill the water tank and reprime the pump (see

paragraph 1). Avoid completely emptying the

tank.

See paragraph 1

Click the tank into place by pressing firmly.

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page14

English

FILTER COFFEE MAKER

Before first use

n Operate the coffee maker for the first time with 1 litre of water, without coffee ground, by filling the

tank and pressing the button on the filter coffee maker.

IMPORTANT

The quality of the water you use determines the taste of your coffee.

You must ensure that the water is freshly drawn from the tap (so that it has not

had the time to stagnate in the air), that it does not smell of chlorine and that it is

relatively cold.

We recommend that you filter your water using a Krups Duo Filter, reference XS 1000, avai-

lable in shops, to be placed in the container provided (D) which is fitted in the coffee maker

water tank.

n Use a no. 4 paper filter.

n Fill the water tank depending on the number of cups you want (Fig. 25).

n Do not exceed the maximum capacity of the water tank as shown by the water level indicator.

n Lift the lid by pressing the OPEN button (Fig. 26).

n Place a paper filter in the filter holder and fill it with ground coffee using the measuring spoon at the

rate of one spoon per cup of coffee (Fig. 27).

n Your appliance is equipped with an aroma selector: this system allows you to obtain a normal coffee

or a more strongly flavoured coffee . Press the button to select the strength of the coffee in

preprogrammed mode or for immediate use (Fig.28).

n Press the button on the coffee maker, the LED glows, and the cycle starts.

n The cycle is complete and your coffee is ready when you hear 3 beeps.

n The coffee maker is fitted with a drip-stop device, allowing you to serve coffee before the water has

finished running through. If you serve yourself a coffee during the cycle, replace the jug quickly to

avoid overflow.

n The jug and its lid can be used for warming up coffee in the microwave.

n Never put the empty jug in the microwave.

n Press the "PROG" button

n The pictogram

flashes; you must set your coffee start time using the "H" and "m" button within 5

seconds; otherwise press the "PROG" button again.

When the time is set, press the "PROG" button to confirm the setting.

Your selection is confirmed, and the display switches back to "clock" mode.

Press the "PROG" button at any time to check the time you have programmed.

n To activate this function, press the "AUTO" button; the cycle will start automatically at the

programmed time.

n You will hear 3 beeps when the cycle is complete.

n To dispose of the used grounds, lift the filter holder out of the coffee maker

n Unplug the appliance.

n Do not clean the appliance while hot.

Coffee

MAKING COFFEE

CoffeeCoffee

SETTING THE TIME FOR A PREPROGRAMMED START

PREPROGRAMMED START

CLEANING

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page15

English

n Clean it with a damp cloth or sponge.

n Never immerse the appliance in water or put it under running water.

n The glass coffee jug, the lid and the filter holder can be washed in the dishwasher.

Descaling

To descale your coffee maker, you can use:

- either a sachet of commercial descaling agent diluted in 250 ml of water

- or 250 ml of white vinegar.

n Pour the descaling agent or vinegar into the tank and start the coffee maker (without filter and without

coffee grounds).

n Allow half the mixture to run into the coffee jug, then turn off the by pressing the button.

n Leave to work for 1 hour.

n Restart the coffee maker by pressing the button and allow the rest of the mixture to run through.

n Rinse the coffee maker by running it twice with a tank of clean water.

The guarantee does not cover coffee makers that fail or work badly due to scale.

DESCALING THE FILTER COFFEE MAKER

Coffee

IN THE EVENT OF A PROBLEM:

Number of cycles between 2 descaling operations

Without duo filter With duo filter

Soft water 60 120

Hard water 40 80

Problems Solutions

The coffee maker does not come on: Check the appliance is properly connected.

There seems to be a leak:

Check if the water tank has been filled above the maxi-

mum level.

The water takes too long to run through

or the appliance makes excessive

noise:

Descale your appliance.

Your appliance still does not work? Contact a Krups approved service center.

END OF LIFE ELECTRICAL AND ELECTRONIC PRODUCT

Environmental protection first!



Your appliance contains a lot of recoverable or recyclable material.



When disposing of it, take it to a collection point or an approved service centre.

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page16

English

: www.krups.com

With a strong commitment to the environment, most of Krups products are

repairable during and after the warranty period. Before returning any defective

products to the point of purchase, please call Krups consumer service directly

at the phone number below for repair options.

Your help to sustain the environment is appreciated!

The Warranty

This product is guaranteed by Krups for a period of 2 years against any manufacturing defect

in materials or workmanship, starting from the initial date of purchase.

The manufacturer's warranty by Krups is an extra benefit which does not affect consumer's

Statutory Rights.

The Krups warranty covers all costs related to restoring the proven defective product so that it

conforms to its original specifications, through the repair or replacement of any defective part

and the necessary labor. At Krups’s choice, a replacement product may be provided instead of

repairing a defective product. Krups’s sole obligation and your exclusive resolution under this

warranty are limited to such repair or replacement.

Conditions & Exclusions

The Krups warranty only applies within USA, Canada & Mexico, and is valid only on presentation

of a proof of purchase. The product can be taken directly in person to an authorized

service centre or must be adequately packaged and returned, by recorded delivery (or equivalent

method of postage), to a Krups authorized service centre. Full address details for each country’s

authorized service centre are listed on the Krups website (www.krups.com

) or by calling the

appropriate telephone number listed below to request the appropriate postal address.

Krups shall not be obliged to repair or replace any product which is not accompanied by a valid

proof of purchase.

This warranty will not cover any damage which could occur as a result of misuse, negligence,

failure to follow Krups instructions, use on current or voltage other than as stamped on the

product, or a modification or unauthorized repair of the product. It also does not cover normal

tear and wear, maintenance or replacement of consumable parts, and the following:

-using the wrong type of water

-scaling (any de-scaling must be carried out according to the instructions for use);

-ingress of water, dust or insects into the product;

-mechanical damages, overloading

-damages or bad results due to wrong voltage or frequency

-accidents including fire, flood, lightning, etc

-professional or commercial use

-damage to any glass or porcelain ware in the product

MANUFACTURER'S WARRANTY

KR_XP2280_NAFTA_NC00026071-01 17/11/11 17:55 Page17

La page charge ...

Krups XP228050 Manuel utilisateur

Marque: Krups

Modèle: XP228050

Catégorie: Cafetières

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Krups XP228050 User manual
español: Krups XP228050 Manual de usuario

Krups XP228050 Manuel utilisateur

Krups XP228050 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents